WISM 7.0.235.0 post-upgrade problem?

I upgraded one of our WISM-1 modules from 7.0.98.0 to 7.0.235.0 last night. For some reason, APs don't join with it unless I tell them specifically to do so. We haven't specified primary & secondary controllers on purpose, allowing the APs to determine from DHCP & the controllers' responses and decide on one based on load. This has always worked great for us.
After upgrading, I couldn't get an AP to join the upgraded wism even after I specified the controller in the AP config. So then I changed my 6506 load balancing to src-dst-mac since that is a known (although seldom seen) issue with APs joining a controller for the first time. We usually keep it set at
src-dst-mixed-ip-port. That worked & the AP joined the upgraded wism. Then I reset the load-balancing algorithm on the 6506, removed the specific controller from the AP's config, rebooted the AP, and all is fine. I thought that solved it. Not.
Any other AP that I reboot tries to join the upgraded wism since it has only 1 AP connected, but it fails and the AP joins the other wism running 7.0.98.0. Even if I change the load balancing algorithm to src-dst-mac, src-dst-ip, or src-mac, it won't join unless I specify the upgraded controller, which I don't want to do. I can see the wism responding to the join requests, but the APs still end up on the other controller. It soulds like the years-old load balancing algorithm issue, but that doesn't seem to be the whole answer this time.
I hope this information makes sense to those that are aware of the issues I bring up. Any ideas why the 7.0.235.0 wism isn't getting APs to join it successfully without my specifying that controller? The config hasn't changed, except for what new or changed defaults exist. I suspect it might have to do with one of those.... Or could it be the two different controller versions returning confusing and different responses to the initial query?
Thanks.
Bill

We're not using the built-in DHCP service on the WISMs.
A wise decision.
I've upgrade our WiSM-1's to this version and we don't have any issues.
However, in the past, we use to host our DHCP server for the WAPs and the clients on a plain Linux box and we noticed that the Linux box took a painfully long, long time to dish out IP addresses to around 1k WAPs. We later moved our DHCP server to InfoBlox and the problems go away.
Any other AP that I reboot tries to join the upgraded wism since it has only 1 AP connected, but it fails and the AP joins the other wism running 7.0.98.0. Even if I change the load balancing algorithm to src-dst-mac, src-dst-ip, or src-mac, it won't join unless I specify the upgraded controller, which I don't want to do. I can see the wism responding to the join requests, but the APs still end up on the other controller. It soulds like the years-old load balancing algorithm issue, but that doesn't seem to be the whole answer this time.
Never saw this problem at all.

Similar Messages

SBA 8.0 (Hor) to SBA 8.0 (Ver) Industry Application Post Upgrade Problem!

Hi All,
I am testing out an upgrade from Siebel 8.0 (Horizontal) to Siebel 8.0 (Vertical) version.
Post upgrade after GUI Fixes, i did a full compile of siebel_sia.srf!
But, after i start my Siebel Services & try to access the Sales or High Tech Manufacturing Application, it doesnt come up.
The log file for both says:
"siebsrvr\log\SSEObjMgr_enu_0025_26214410.log 8.0 SIA [20405] ENU
ObjMgrSRFLog Error 1 00000006486b09f4:0 2008-07-02 13:33:39 (cdf.cpp (668)) SBL-DAT-00142: Could not open repository file 'd:\sia80\siebsrvr\objects\enu\siebel_sia.srf'.
File does not exist or may be in use by another process.
ObjMgrCTLog Error 1 00000006486b09f4:0 2008-07-02 13:33:39 (ctxtmgr.cpp (4492)) SBL-SVC-00208: Please login first."
Any idea why this is happening? The SRF file exists on the correct location & i dont see any other application accessing the same.
Regards,
Shalabhsneha

Double-check with Siebel Tools that is the same file.
Check that the new Siebel application is shut down properly and has no "dangling" processes before restart.

Pertaining Watches thread in Post Upgrade Problems Forum

I have posted a question pertaining the watches, I'm not able to see the red indicator nor receiving e-mail.
Justin, sorry for the very late reply.
I didn't see your reply and now the threads are read only, so I had no other choice but to post here.
The threads I watch I am able to see them in the "Watches" in my Control Panel but I do not see the red indicator and I do not receive watches e-mail.
Thanks in Advance for your help.
Regards,
Tony

The watch e-mails have stopped since the first couple of days of the upgrade, back than I thought they were off, so I waited, but noticed no one was talking about it.
I checked my mailbox today and I saw a whole bunch of watch mails, some from Sunday 23 November and dated way back till 27 October, but none for this thread. It's weird, there are watch-mails for some threads and not for others.
Have you guys uploaded anything??
I haven't change the mail address from the control panel, at least not after the upgrade, but I might have edited that profile page to make sure of my handle, there were cases where the e-mail address was showing instead of the handle at post upgrade.
However I would want to change the e-mail where I receive the watch mails as soon as they start working.
oh! one more thing, I still don't see the red indicators for watches on thread list in the forums.
Thanks for your help guys, really appreciate it.
Tony

Post upgrade problem activating technical chains

Hi
After upgrade do version 7.01 I would like to collect and activate technical process chains.
During this proces I got error "Shadow object 0PAK_...... cannot be expanded; chain is inconsistant" and not all Infopackages were collected.
Any sugestion what is cause of this problem.
Adam
THX

Hi Dhanya,
Thanks for your reply.
When activating the process chain, I have selected all infopackages that were collected automatically by the system (with the option "In the Data Flow Before"). I also tried to find these infopackages myself in the Business Content (in ISIP (Infopackage) object type), still no success.
I also thought I could create these infopackages manually, but I have absolutely no idea on what they are expected to do: loading? From where to where? Activating data? Changing attributes? I don't know.
In RSPC I can see these infopackages as a step in the chain, but only with their technical name which does not help me to find out what is the source and target of that loading.
Cheers,
Csaba

10.4.6 Upgrade - post upgrade problems

I have recently upgraded from 10.4.5 t 10.4.6. Since doing so, I have experienced several problems related to my internet connection etc. When Software Update runs, I always get a (-1001) timeout error and 'Software Update can't check for updates because of a network problem.' However, when I run network diagnostics, everything is normal. Similarly, I am having intermittent issues with my internet connection - sometimes it works sometimes it doesn't. When it does work it runs very slowly and sometimes the pages half load and just hang. I have tried using my wireless internet connection with my Windows laptop and everything is fine. I assume the problem therefore is 10.4.6 as nothing else has changed. I am a very frustrated user at the moment. Has anyone any thoughts?

Revert to a hardwire internet connection and see if that fixes the problem. If so, then do a search in these forums for "wireless" or "airport" problems.

7.6.2 post upgrade problems with some users only

Having upgraded to itunes 7.6.2 I am getting some weird problems. My user account itunes seems to work fine, but if my daughter logs onto the machine itunes will not access the store homepage - it just hangs and eventually gives error -50. Exploring a little more and it can be persuaded to get onto the store, but only throught the search page and then not to the music store!
Checking other accounts on the machine reveals the same pattern, one account works fine, the other does not.
It may be relevant that the two accounts that do not work are both childrens accounts with parental controls enabled.

Probably a firewall / parental control issue. If you temporarily disable parental controls, does everything work as it should?

4s contacts post-upgrade problem

So it might be my noob status as an Iphone user but I installed the update to my phone and now the contacts that were on my phone that I had synced from my Mac do not show up when they text and call. So for example all the contacts on my phone (both from mac and ones entered) show up in the address book as normal; however, when one of the ones I added from my mac calls or texts it shows up as just their number as if they are not an existing contact. I tried deleting all the contacts through sync on itunes and reloading them but that doesn't help the situation. What do I do?

I figured it out, it was my bad I had specified the path to include the apex directory which gets created when you unzip apex 3.1.
So I specified the path as apex3.1/apex/ which is APEX_HOME/apex. Instead I needed to specify only the base directory which was apex3.1
(wrong)
@apxldimg.sql /apex3.1/apex
(right)
@apxldimg.sql /apex3.1

Given so many posts about problems, is upgrading to maverick worth it?

Given so many posts about problems, is upgrading to OS X maverick worth it?
I am content using Snow Leopard OS X 10.6.8. But my most recent Garmin GPS map updates returned a message that stated, "Mac OSX 10.6 is an older OSX version that is no longer compatible with modern software. We will be ending support for this operating system soon. To continue using Garmin Express, please upgrade your operating system."
As others have noted, you don't hear from the users who have installed this upgrade successfully. I've read about problems installing the upgrade and then incompatibilities with other applications once it is installed. Would appreciate your experience and thoughts. Thanks.

There are several excellent suggestions here.
What I did was clone my Snow Leopard drive to a second hard drive, then installed Mavericks on the clone.
I now have a working Snow Leopard drive as well as a Mavericks drive. I bounce back and forth between them.
I have symlinks set up so all my documents created on the Mavericks drive go to the Snow Leopard drive, but I have copies of all my applications on both drives. It just seemed easier...
I had to disable App Nap in both Quickeys and Keyboard Maestro, but they both seem to work well, and neither is the latest version. (Well, Quickeys is the latest version, but it's not a recent version.)
I only check email in Snow Leopard, never in Mavericks, so my Inbox is not scattered over both systems.
The Mavericks disk takes longer to boot, and it does occasionally seem sluggish, but it's not a deal-breaker. Like many, I have some legacy software I use, so I don't want to commit to Mavericks full time. But it's nice being able to use both.
I do like using Safari in full-screen mode, but that's the only program I use full-screen for.
Hope this helps.
Andy

ASU-process POST Upgrade Step on SQL database

Hi All,
To check this message in the right format kindly click on reply first then click on quote original icon ("").
I am performing an upgrade from R/3 4.7 to ERP 6.0 SR3, while doing upgrade sapup asking me To perform the manual application specific post upgrade step.
This phase says to run ASU toolbox by using tx /n/asu/upgrade. when i run this tx is show the below list of steps to be performed with showing severity level of some as optional and many as obligatory.
Task List                                                                                Severity     SAP R/3 release frm     SAP R/3 release to
IS-OIL Application Test 600                                                 Optional
KP06xx: Termination SYNTAX_ERROR                                                 Obligatory     470                           500
CGPL: Entries are blank after upgrade                                                Obligatory
Error handling of task group execution                                Optional
Mobile device cannot confirm TO after release upgrade     Obligatory     470                         600
Mobile device doesn't find transfer orders after upgrade     Obligatory     470                          600
Grantee Management - Upgrade from EA-PS 2.00 to ECC 600     Obligatory
Convert customizing for warehouse funds ctr scenarios     Optional
Various problems classification commitment items (class type     Obligatory
Unauthorized error messages udring fiscal year change/reassi     Obligatory
RFFMUDX1 migrates incomplete budgeting tables                          Obligatory
Non-7bit-ASCII character used for BCS key figures             Obligatory
Changes in TKEDR for /ISDFPS/RFFMDISTDERIVALE          Obligatory
BCS - Tool for Deleting Obsolete Derivation Strategies     Obligatory
BCS Syntax Error on Upgrade from EA-PS 2.00 to ECC 600     Obligatory
Migration to ERP 6.0 (EA-PS 6.00)                                         Obligatory
Migration EA-PS 2.00 to ERP 5.0 (EA-PS 5.00)                      Obligatory
Missing initialization of new fields in table ANLZ                  Obligatory     46C                       470
Activating VMC for the Internet Pricing and Configurator     Obligatory
Customer specific BSEG-fields not transferred                  Optional
Conversion of report headers in drilldown-reporting            Optional                                   600
IBase: Upgrade to Release 4.6C and higher                         Optional     46C                         600
ZSAPRCKML_COGS: Upgrade to release 4.7 or higher     Optional     46C                      470
Conversion of CO-Total-Tables                                              Obligatory     46C                      500
Conversion of CO-line-item table COEP                                Obligatory     46C                       600
New General Ledger, problems in CO-documents                 Obligatory                               500
No receivers found in allocations                                          Obligatory     46C                        470
Conversion Of New Process Parameter Long Texts For Search     Optional     110                       600
Migration of process parameters in recipe management     Optional     110                        600
FAQ new depreciation calculation                                        Optional                                600
Upgrading to SAP R/3 47x200 and SAP ECC 500 with RMGMT     Obligatory     100                       500
Reloading Table T512W                                                        Optional
Converting Short Texts                                                         Obligatory
Migrating Data                                                                         Optional     4.7
Activating SAP ECC Extensions                                          Optional
I am not sure about which steps I have to perform, I am a bit confused.. because some are optional and some are not relevant to my release (as target or source release is different from mine). and also few things are not applied in my envirnoment hence those steps are also not relevant.
Please suggest me, how to proceed and what to do. please guide if i skip this step now and later on I apply latest SP than still I need to do all this.
Regards
Vinay

Hi All,
I also faced a similar issue during upgrade. Some useful findings.
1. Only super user can access this /n/ASU/START
2. All the obligatory executable tasks are automatically performed by the system automatically during upgrade.      SAPADM. Only errors (if any) are to be corrected.
3. Some of the tasks are only to go through some SAP notes as a precaution before upgrade.
4. Execute all the checks /n/ASU/UPGRADE
5. This surely can be skipped, but not advisable.
regards,
Amit

Upgrade step ASU-process post upgrade step

Hi All,
To check this message in the right format kindly click on reply first then click on quote original icon ("").
I am performing an upgrade from R/3 4.7 to ERP 6.0 SR3, while doing upgrade sapup asking me To perform the manual application specific post upgrade step.
This phase says to run ASU toolbox by using tx /n/asu/upgrade. when i run this tx is show the below list of steps to be performed with showing severity level of some as optional and many as obligatory.
Task List                                                                                Severity     SAP R/3 release frm     SAP R/3 release to
IS-OIL Application Test 600                                                 Optional
KP06xx: Termination SYNTAX_ERROR                                                 Obligatory     470                           500
CGPL: Entries are blank after upgrade                                                Obligatory
Error handling of task group execution                                Optional
Mobile device cannot confirm TO after release upgrade     Obligatory     470                         600
Mobile device doesn't find transfer orders after upgrade     Obligatory     470                          600
Grantee Management - Upgrade from EA-PS 2.00 to ECC 600     Obligatory
Convert customizing for warehouse funds ctr scenarios     Optional
Various problems classification commitment items (class type     Obligatory
Unauthorized error messages udring fiscal year change/reassi     Obligatory
RFFMUDX1 migrates incomplete budgeting tables                          Obligatory
Non-7bit-ASCII character used for BCS key figures             Obligatory
Changes in TKEDR for /ISDFPS/RFFMDISTDERIVALE          Obligatory
BCS - Tool for Deleting Obsolete Derivation Strategies     Obligatory
BCS Syntax Error on Upgrade from EA-PS 2.00 to ECC 600     Obligatory
Migration to ERP 6.0 (EA-PS 6.00)                                         Obligatory
Migration EA-PS 2.00 to ERP 5.0 (EA-PS 5.00)                      Obligatory
Missing initialization of new fields in table ANLZ                  Obligatory     46C                       470
Activating VMC for the Internet Pricing and Configurator     Obligatory
Customer specific BSEG-fields not transferred                  Optional
Conversion of report headers in drilldown-reporting            Optional                                   600
IBase: Upgrade to Release 4.6C and higher                         Optional     46C                         600
ZSAPRCKML_COGS: Upgrade to release 4.7 or higher     Optional     46C                      470
Conversion of CO-Total-Tables                                              Obligatory     46C                      500
Conversion of CO-line-item table COEP                                Obligatory     46C                       600
New General Ledger, problems in CO-documents                 Obligatory                               500
No receivers found in allocations                                          Obligatory     46C                        470
Conversion Of New Process Parameter Long Texts For Search     Optional     110                       600
Migration of process parameters in recipe management     Optional     110                        600
FAQ new depreciation calculation                                        Optional                                600
Upgrading to SAP R/3 47x200 and SAP ECC 500 with RMGMT     Obligatory     100                       500
Reloading Table T512W                                                        Optional
Converting Short Texts                                                         Obligatory
Migrating Data                                                                         Optional     4.7
Activating SAP ECC Extensions                                          Optional
I am not sure about which steps I have to perform, I am a bit confused.. because some are optional and some are not relevant to my release (as target or source release is different from mine). and also few things are not applied in my envirnoment hence those steps are also not relevant.
Please suggest me, how to proceed and what to do. please guide if i skip this step now and later on I apply latest SP than still I need to do all this.
Regards
Vinay
Edited by: Vinay Paul on Sep 11, 2009 10:11 PM

Hi All,
I also faced a similar issue during upgrade. Some useful findings.
1. Only super user can access this /n/ASU/START
2. All the obligatory executable tasks are automatically performed by the system automatically during upgrade.      SAPADM. Only errors (if any) are to be corrected.
3. Some of the tasks are only to go through some SAP notes as a precaution before upgrade.
4. Execute all the checks /n/ASU/UPGRADE
5. This surely can be skipped, but not advisable.
regards,
Amit

Ipod Touch 3.0 Upgrade problems

Hi there;
I've found a few similar problems out there on the forum, but none that contain a solution that has helped.
Basically I tried to upgrade my 2nd generation ipod touch from software version 2.2 to the new 3.0. On my main box pc, on which I have used Itunes for ages, I first upgraded to Itunes 8.2.0.23 and then I was further prompted to upgrade my ipod software to version 3.0.
The download went fine, but on installing the upgrade the ipod locked on the Apple screen (no progress bar) and I was presented with a window saying the update had failed. When going back to Itunes I was told that my ipod was in recovery mode and needed to be restored. After a further long period staring at an Apple, I get an error saying the Ipod could not be restored (code 1603).
After repeated attempts I decided to use my laptop, which has never had itunes installed as it's only a week old. I installed Itunes, started it and connected the Ipod. Again it said it was in recovery mode, so I asked it to restore it. Interestingly it downloaded v2.2 and restored successfully, although it was blanked back to purchase state. It then told me about the 3.0 upgrade, so (stupidly) figuring that this was a new state ipod on a different machine with a clean, new install of Itunes, I thought ok!
Same result, locks on the Apple screen and eventually tells me the update failed. Now when I restore on the laptop, I believe it's trying to restore the newly downloaded 3.0 instead of the (working) 2.2 and it fails with the error above.
I'm pretty confident that I can use a 3rd pc to restore back to 2.2, but why oh why is this being so problematic? Is 3.0 broken for some ipods out there?
I've tried a few solutions I've found, such as restarting the Apple Mobile Service, and using a different machine is like reinstalling/using different usb's (didn't work anyway as I've tried 2 ports on the laptop now), holding down the power/standby buttons to hard reset it. I'm about to create a new user on Vista32 HP to see if I can get it to restore.
What's going on?!
Many thanks in advance for any help.
Graeme
Btw:m I did pay for the update through Itunes of course. The new laptop install recognised that I'd paid already and downloaded without a further purchase.

RESOLVED
Typically, within 1/2 hour of posting my problem, I tried a random solution and it randomly worked. After quitting itunes, disconnecting the ipod (stuck permanently on the Apple screen after the last update failure, so I held down the power/stby buttons to turn it off). I then dug into the following folder where itunes keeps its update downloads...
c:\users\((username))\AppData\Roaming\Apple Computer\iTunes\iPod Software Updates
... and moved the two update files (one for 2.2 and another for 3.0) to the recycle bin. I ran iTunes, turned on the ipod with a hard reset by using the power/stby buttons together (to get the screen with the usb connector pointing to iTunes), then connected it. Got the screen saying about Recovery mode and needing to restore ... so I restored, got the window saying about 3.0... it downloaded and installed (progress bar and everything) successfully.
Farce complete. I don't think I'll update again!!!
I hope this possibly helps others out there, if they encounter this freakish seemingly rare problem.
Graeme

Post-upgrade tasks for OWB 10g Release 2

Hi,
we're planning to upgrade from OWB 10.1.0.2 to 10.2.x.
Now, I'm trying to get a clear view on what will be the "post-upgrade" tasks, in terms of manual adaptations, corrections, etc. to get everything back up and running after the upgrade ...
E.g. : by means of test al already exported a dimension, and imported it in the 10.2 repository ... Turned out that in the pre-10.2 version, there were no validation problems, but as from 10.2 (although the upgrade and import were successful), I got 19 warnings and 2 errors ... because each level needs to have a business or surrogate key ...
It' s things like that I'm especially interested in, in order to determine the workload after the upgrade ...
So, feel free to share your experiences ; I'm looking forward to read them!
Thanks!
Grtz.

Here are some from my list. I stopped maintaining it a while ago, we have lots more where this came from. Some of it also apply to older versions of OWB.
Key lookup     You are to choose input and output attributes BEFORE being able to choose loookup table, all in a time consuming wizard
Expressions     Copy and paste into expression editor, validation fails for expressions using lowercase (such as "upper" or "substr")
Renaming attributes     Not possible anymore, you need to open details
Adding a table component     You must browse in a tree structure (time consuming), not search functionality anymore
Import     Import converting from 9.2 hangs after 15% in about 10% of all imports
Import     Some mappings are not possible to import, a total rewrite is necessary
Deployment     You can only deploy about 5-10 times before you need to restart OWB
Memory leak     If something goes wrong in OWB, memory is never cleared - JAWAW.exe needs to be removed manually from memory
Import     Importing mappings one by one (as this is sometimes needed due to OWB), the last directory used is OF COURSE not default when importing the next time
OWB GUI / mapping editor     When working with components in the mapping editor, an object hidden behind the object you are actually working with is selected prior to the object in visual focus to the user
BUG!     Urgent: CASE - wrong generated Code
ANSI JOINS     Remove ANSI-SQL from mapping configuration, otherwise (+) outer joins will not work
Transformations     Not possible to enter a transformation such as "sysdate", you must find it in a huge tree structure list (no search available)

Audio Tracks on my iPhone stopped working post upgraded to iOS 5.

Audio Tracks on my iPhone stopped working post upgraded to iOS 5.
Quiet a lot of my tracks do not play on my iPhone 4 after I upgraded to iOS 5. The the seeker bar does not progress and it looks stuck.
Could someone please help.
Regards,
S!d

Hi !
I am currently having the same problem, since I upgraded my iPhone 4 to iOS 5, many tracks don't work. They were working before. Some are working but half isn't.
Tried to restore, remake playlist, delete every tracks et put them back. Same prob.
Please help !
Regards,
Rom

Error on Oracle 11gR2 RAC database Post upgrade step

[Upgrade the Oracle Clusterware Configuration|http://docs.oracle.com/cd/E11882_01/server.112/e23633/afterup.htm] Problem Description:
O.S Version: HP-UX B.11.31 U ia64
It is upgrading of Oracle RAC 2 node database from 11.1.0.7.0 to 11.2.0.3.0
I receive following error while perfoming the post upgrade step
indba1 racdb> srvctl upgrade database -d racdb -o /app/oracle/product/11.2.0.3/db
PRCD-1231 : Failed to upgrade configuration of database racdb to version 11.2.0.3.0 in new Oracle home /app/oracle/product/11.2.0.3/db
PRKC-1136 : Unable to find version for database with name racdb
Actually I am performing the step "Upgrade the Oracle Clusterware Configuration" whill getting the error.
When I tried on below;
indba1 racdbp> srvctl upgrade database -d racdb -o /app/oracle/product/11.2.0.3/db
PRCD-1231 : Failed to upgrade configuration of database racdb to version 11.2.0.3.0 in new Oracle home /app/oracle/product/11.2.0.3/db
PRKC-1136 : Unable to find version for database with name racdb

Output from Oracle 11.1.0.7 Home:
oracle@indba1:/app/oracle/product/11g/db_1 $ srvctl config database -d racdb
PRKR-1001 : cluster database racdb does not exist
PRKO-2005 : Application error: Failure in getting Cluster Database Configuration for: racdb
Output from Oracle 11.2.0.3 Home:
oracle@usfsdba1:/app/oracle/product/11.2.0.3/db $ srvctl config database -d racdb
PRKR-1001 : cluster database racdb does not exist
PRKO-2005 : Application error: Failure in getting Cluster Database Configuration for: racdb

Syntax Error in Web UI component post upgrade

Hi Experts,
We have a enhanced component in IC agent which is giving syntax error post upgrade from 7.0 to EHP2. It seems some attributes have been removed/altered in the new super class.
In this case do we need to delete the component enhancement and re do the effort or is there any way to regenerate the enhanced component ?
Thanks, Please help.
Rohit

Hi Rohit,
I've written a few blogs where I collected the different steps necessary in CRM after an EhP or SP upgrade. Furthermore I described solutions to common problems in these blogs. Please have a look an see if one of the described approaches is suitable for your problem.
http://scn.sap.com/docs/DOC-44983
http://scn.sap.com/docs/DOC-49317
http://scn.sap.com/community/crm/upgrades-and-enhancement-packs/blog/2014/02/21/sap-crm-ehp3-upgrade
Best,
Christian

WISM 7.0.235.0 post-upgrade problem?

Similar Messages

Maybe you are looking for