WISM controller stays "Started KeepAlive"

After an upgrade of both controllers on a WiSM module from 4.1.171.0 to 5.0.148.0 the first stays in
"Operational Status of the Controller : Started KeepAlive"
Even after setting to factory defaults or repowering the module.
Any idea what's problem

the service port is configured to get an IP from the dedicated management vlan where a local dhcp service is provided.
...and in the meantime after several controller and module resets it works without config changes....
So I'm wondering whether this is usable in an productive environement.

Similar Messages

  • Cisco WISM2 started keepalive issue

    Hi all,
    I faced a problem in my WISM2 in 6500 when I issue the command of #show WISM status I found that the status of the wism is "Started KeepAlive "
    not operational 
    please advice if there is a solution except that I reload the WISM.

    Is your WiSM service-vlan configured?
    Steve

  • Service won't stay started!

    I'm running ZFH 5.1.
    The darn service that runs on the windows servers won't stay started.
    It will start up fine, run for about 5 minutes and then stop.
    In the event logs there are no entries to show errors or problems.
    The servers are Windows 2003 or Windows 2000. I've tried it on both versions.
    Any ideas?
    Thanks,
    Cheryl

    Cheryl,
    It appears that in the past few days you have not received a response to your
    posting. That concerns us, and has triggered this automated reply.
    Has your problem been resolved? If not, you might try one of the following options:
    - Do a search of our knowledgebase at http://support.novell.com/search/kb_index.jsp
    - Check all of the other support tools and options available at
    http://support.novell.com.
    - You could also try posting your message again. Make sure it is posted in the
    correct newsgroup. (http://support.novell.com/forums)
    Be sure to read the forum FAQ about what to expect in the way of responses:
    http://support.novell.com/forums/faq_general.html
    If this is a reply to a duplicate posting, please ignore and accept our apologies
    and rest assured we will issue a stern reprimand to our posting bot.
    Good luck!
    Your Novell Product Support Forums Team
    http://support.novell.com/forums/

  • Regulatory domain on WiSM Controller

    Can we change the regulatory domain of the WISM controller. The region I am working in, the max EIRP allowed in on 14 dBm. Is it a right step if I change the regulatpry domain of the WISM controller so that the EIRP of 1524 can be increased?

    The EIRP is observed on AP. The Radio elements ( including Antennae ) are present in AP not controllers. So if AP has been regulated to emit maxm @14dBm , you cannot observe more power beyond that even if you configure it via controllers.

  • Shutdown Second WISM controller in 6509

    We have the task to shutdown our secondary WISM controllers and bring up new 5508 controllers. I'd like to shut down WISM controller 2 and re-use the IP on the new WLC. Is there a way to shut down or disable the second WISM so i can reuse that IP? When i attempt to disable the interface i get the following:
    (WiSM-slot6-2) >config interface ap-manager management disable
    Error - This command is only applicable to dynamic interfaces.
    (WiSM-slot6-2) >show interface summary
    Interface Name                   Port Vlan Id  IP Address      Type    Ap Mgr Guest
    ap-manager                       LAG  untagged 132.189.242.236 Static  Yes    No   
    guest                            LAG  500      192.168.124.33  Dynamic No     No   
    management                       LAG  untagged 132.189.242.232 Static  No     No   
    service-port                     N/A  N/A      192.168.254.4   Static  No     No   
    virtual                          N/A  N/A      1.1.1.1         Static  No     No   
    wireless-users                   LAG  10       10.96.128.13    Dynamic No     No   
    (WiSM-slot6-2) >
    We currently have active wireless clients on WISM Controller 1 in the same chassis.
    Thanks,
    Jay

    Why not just use a different ip initially and move all the access points to the 5508 and then change the management ip to the old WiSM IP address. You can even change the management of the WiSM first and then bring up the new 5508 on the old WiSM IP address also.  You can do what Leo mentioned or even power down the module.  
    -Scott

  • Configure WISM controller Vlan Management

    Anyone can clarify me if is correct or not to confifure the WISM controller on a 6509 management in VLAN1 or is a must to put ( as Cisco Described : http://www.cisco.com/en/US/docs/wireless/technology/wism/technical/reference/appnote.html#wp40841 ) in VLAN 40 or any aother VLAN different by Vlan 1 ?
    This question because now we found a broadcast storm passing through VLAN 1 and through the wirelles network
    Thanks !

    you an use whatever VLAN you wish. If all of your network is managed via VLAN 1, than that is fine. I know that some people recommend not using VLAN 1, but that is a personal call.

  • WiSM Controller 1 is Down

    Dear all,
    I have WiSM WLAN Service Module installed on 6509 core switch, everything was working fine, suddenly the first controller became unavailable and showing the following output
    CoreSwitch# <strong>show wism mod 4 controller 1 status</strong>
    WiSM Controller 1 in Slot 4
    Operational Status of the Controller : Service Port Up
    Service VLAN : 144
    Service Port : 9
    Service Port Mac Address : 0000.0000.0000
    Service IP Address : 0.0.0.0
    Management IP Address : 0.0.0.0
    Software Version :
    Port Channel Number : 289
    Allowed vlan list : empty
    Native VLAN ID : default
    WCP Keep Alive Missed : 0
    Second controller is working fine and showing the following:
    CoreSwitch# show wism mod 4 controller 2 status
    WiSM Controller 2 in Slot 4
    Operational Status of the Controller : Oper-Up
    Service VLAN : 144
    Service Port : 10
    Service Port Mac Address : 001a.6c22.8f62
    Service IP Address : 192.168.100.3
    Management IP Address : 10.41.1.21
    Software Version : 4.2.176.0
    Port Channel Number : 290
    Allowed vlan list : empty
    Native VLAN ID : default
    WCP Keep Alive Missed : 0
    <strong>Anybody can help??</strong>

    yup ... i had that on a install a few months back ... had to do a RMA....
    I would call TAC and get this replaced. Dont waste your time on this one ...

  • Wism controller does not show url redirection spalash page

    Hi 
    Wism controller does not show url redirection/splash page .
    client takes the ip from the  dhcp server. when browsing its not going to the authentication page as usual
    Thank you 

    Can you elaborate on your issue... really hard to follow.  To me, it seems like you want to use a guest splash page.  The client associates to the open guest ssid and get's an ip address.  Now the user has to open a browser to get the portal page correct?  This has nothing to do with the WLC, but the OS on the device.  Some devices can detect if no internet is present after authentication and obtaining an address.  This means the device will automatically open a browser to present the user with the splash page.  Other devices will require the user to open a browser to get the login screen.
    Scott

  • Wism Controller 2 doesn't get service port IP but Controller 1 does

    I followed the documentation for setting up the WiSM. Controller 1 is up and fine. I see in dhcp bindings, that Controller 2 is getting a DHCP address and when I "session slot 9 pro 2" it tries to connect to that dhcp address, but on a "show wism status" the service-port of controller 2 is 0.0.0.0
    Has anyone encountered this problem?
    Thanks

    Hi..
    What about the connectivity?? do we still have the access to the WLC 2?? either from telnet or the GUI?? or will the session to the WLC work?
    Regards
    Surendra

  • Adding HASH keys from one WISM controller to all other controllers

    I have 4 controllers(2 WISMS) on one controller we have ~30 MAC/SSC/KEY HASH
    the other 3 have ~half. How can I copy all the MAC/SSC/KEY HASH to the rest of the controllers. I don't have access to the station that converted the AP's. I would prefernot to have to add each individually.

    Hi, if you have an WCS you can use the AP Authorization Template, you can find it under Configure > Templates > Security > AP Authorization. Use the csv File generated by the Conversion Tool and import it to WCS. Then push the Template to the Controllers. Otherwise you can do it directly on the Controller, under Security > AP Authorization. Insert the AP MAC, Certififcate Type SSC and the RSA Key Hash. Regards, Michael

  • 2K8R2 Domain Controller not Starting when isolated

    Hello. I am having an issue with a 2008 R2 Domain Controller. This DC is not a FSMO role holder. When this DC is fired up off the network, in an isolated environment (switch, couple pc's and the DC) it does not fire up as a DC. DNS and DHCP are non-functional,
    network ID shows as Undefined Network.  Now, if I disable then re-enable the NIC, everything works. Netowrk shows mycompany.com and DNS and DHCP function. DNS in the NIC properties points to itself (actual IP not 127.0.0.1) with no other DNS servers configured
    on the NIC.
    This seems to be a new thing in my environment, as we have done small isolated networks before for brief periods of time.I have also seen this behavior at a branch office when power is lost and the DC starts up before the ipsec tunnel back is established.
    Anyone have any ideas?
    Thanks,
    Jim

    Hi,
    Is there any error in event log?
    Did you have any other DCs replicate with this DC?
    Please refer to the similar thread:
    Isolated Domain Controller Problem                                 
    http://social.technet.microsoft.com/Forums/en-US/5015ec63-ed3c-435d-b27c-4e7ab1f2c824/isolated-domain-controller-problem?forum=winserverDS
    Regards.
    If you have any feedback on our support, please click
    here
    Vivian Wang

  • WISM Controller and 6500 Switch power cycled

    Has anyone come across this issue where if the 6500 switch is reloaded or power cycled that 8 out of 10 interfaces on the WISM become administratively down this does not happen if you reload just the wism or power cycle the controller.
    the softwear loaded on the switch is as follows.
    Supervisor Engine 720 10GE with f/w 8.5(2) and s/w 12.2(33)SXH
    WiSM WLAN Service Module with f/w 12.2(14r)S5 and s/w 12.2(33)SXH
    any suggestions as to how to sort this so it loads all the interfaces as up from the power cycle or reload of the switch would be welcome have already made sure the config is saved but still happens.
    Jeremy

    1. I believe a 6509 can handle 5 WiSMs, though I've found 4 more realistic when considering the need for uplinks and service modules.
    2. Based on 5 WiSMs, you can have 1500 per chassis. Again, I tend to stick with 4, or 1200 APs per chassis.
    3. There is no hard limit that I am aware of. WCS on a VERY high-end server can handle ~2500 APs when running Linux WCS. As with the above, this works well with 1 WCS per 2 chassis if each has 4 WiSMs.

  • OMS won't stay STARTed

    Successful install in re all else, but Oracle Mgt Server starts, then stops. It never starts and runs. The system's event viewer tells me "process termination failed for JRE. %2.", and directs me to the file
    C:\oracle\ora92\sysman\log\oms.nohup
    In that file, there are lots of java.lang.NullPointerExceptions, with the occasional
    oracle.sysman.vxx.vxxo.VxxoNameNotFoundException: VXX-2009 : Could not find service context
    and
    exception VxaInvalidStateException{wstring reason="VXA-3032 : Error in attempting to bind OMS Services over ORB. Shutting down oms";}
    finally leading to
    "Could not start management server. Initialization failure"
    which, of course, I already knew...
    An earlier search of the forums hinted that using the plain old IP address insead of the DHCP name (in lisnerctl.ora and / or tnsnames.ora) but the behavior is unchanged.
    This is a desktop install, on XP Professional V.2002 service pack 1, on a Dell 2.39 GHz pentium, 4cpu, 256MB ram.
    jeez, it should work... HELP?
    Thanks in advance -- Sara Riley

    hi mike,
    i m facing the same problem as me also a beginner...
    what i did is created a database and then created repository for it...
    now i m getting the VTK-1000 error while trying to logon
    login name/pwd/server i m trying is
    sysman/oem_temp/oracleofshome30 or oracleofshome30managementserver
    can u plz help me out on this my e-mailid is
    [email protected]
    <BLOCKQUOTE><font size="1" face="Verdana, Arial, Helvetica">quote:</font><HR>Originally posted by Mike Jensen ([email protected]):
    I'm relatively new to Oracle 8i, and am trying to launch the oracle management service. I've been through all the archives, and not found a good answer. Here's what I've done:
    1 - created a repository in the database of interest. Now in doing so I've setup a username and password equal to one of the users in the DB. I've also tried by creating a new user. Both seem to configure just fine, but...
    2 - When I try to start the NT service, it comes up as started, then if I try connect quickly I get a 'busy initializing' message (must mean I'm talking to the correct OMS), but then the service goes down.
    In attempting to connect I'm providing the same username/password as the repository. I've used the configuration assistant to change the username/password to a couple different options, to no avail.
    Can someone help or point to documentation on how this thing should be setup?
    Thank you in advance for any help you can offer.<HR></BLOCKQUOTE>
    null

  • Can't join AP with WiSM controller

    We have a (brand new) WiSM blade installed in a 6509. The configuration looks ok, but when we try to register (join?) an AP with the controler the process fails. The controler shows the AP in the status display but the AP reboots, claiming that no join-response was received.
    The controler claims that it sent the join-response, however imediatly after that it generates the error "Slot ID 0 is not valid for AP".
    Here is a more complete log:
    Tue Aug 22 16:08:47 2006: sshpmGetOpensslPrivateKeyFromCID: match in row 2
    Tue Aug 22 16:08:47 2006: sshpmPrivateKeyEncrypt: calling RSA_private_encrypt with 236 bytes
    Tue Aug 22 16:08:47 2006: sshpmPrivateKeyEncrypt: RSA_private_encrypt returned 256
    Tue Aug 22 16:08:47 2006: sshpmPrivateKeyEncrypt: calling RSA_private_encrypt with 24 bytes
    Tue Aug 22 16:08:47 2006: sshpmPrivateKeyEncrypt: RSA_private_encrypt returned 256
    Tue Aug 22 16:08:47 2006: sshpmPrivateKeyEncrypt: encrypted bytes: 512
    Tue Aug 22 16:08:47 2006: 00:18:b9:xx:xx:xx Successfully transmission of LWAPP Join-Reply to AP 00:18:b9:xx:xx:xx
    Tue Aug 22 16:08:48 2006: 00:18:b9:xx:xx:xx Slot ID 0 is not valid for AP 00:18:B9:xx:xx:xx
    Tue Aug 22 16:08:48 2006: 00:18:b9:82:29:2a Slot ID 0 is not valid for AP 00:18:B9:xx:xx:xx
    Any thoughts, hints etc. We do have another controler that is working.
    thanks
    Phil

    Turns out the SlotID 0 issue was a red herring. There was a bug in the network topology that prevented the join-reply from reaching the AP.

  • Mac G5 won't stay started

    Here's my current problem: If I boot up my Power Mac G5, I get the gray apple screen and then it just shuts off. I can boot from a CD, and when I use the install CD/Disk Utility to check out the disk, I get this:
    Missing thread record (id=34882)
    Invalid extent entry
    Invalid key length
    Volume check failed
    Error: Filesystem verify or repair failed
    Any ideas what's up with it?

    Hi Thomas Zahler-
    Then you probably are simply suffering a corrupted directory. That is why I suggest trying to repair the drive first.
    DiskWarrior may be your friend: DiskWarrior
    Luck-
    -DaddyPaycheck

Maybe you are looking for