WiSM, unable to see Interface after adding.

We have an up and running WiSM, for about 9 months. It resides in a 6509 chassis.
I needed to add a new interface for another subnet (previous one was getting over ran, and we have a new project)
I went through the process of adding the interface. I ensured it was active.
At present, from the 6509 I am unable to ping the interface's IP, but I am able to ping that networks gateway.
From the WiSM, I am able to ping the interface's IP, but unable to ping the gateway.
I was not the original configurator of the WiSM and the 6509 build. That person is no longer around.
On the 6509 I have ensured that the : show interface trunk shows the VLAN in question.
I have searched numerous times, and I feel like there is just some nefarious item I am missing on the creation of new Interfaces between the WiSM and 6509.
Any input would be appreciated.
Thanks

Have you double checked the vlan tag, subnet mask, etc for the new interface on the WLC? Usually when you cannot ping an interface on the WLC (although pings are the lowest priority) it is a configuration error on the above, or the trunk not allowing that interface, etc.
Thanks,
Lee

Similar Messages

I am unable to see a newly added PC under devices in SCCM2012R2 console

Hi,
I am unable to see a newly added PC under devices in SCCM2012R2 console. Plz help me how to add a system to SCCM2012R2 console

Where and how have you added computers? Computers are added when the ConfigMgr client is installed or by a discovery method.
Torsten Meringer | http://www.mssccmfaq.de

Unable to see interface on ASA 5510 Firewall

Hi All,
I am unable to see 4th interface on my firewall i.e fastether0/3 on my firewall ASA 5510.
Below is the output.
ciscoasa# sh int ip br
Interface                  IP-Address      OK? Method Status                Protocol
Ethernet0/0                x.x.x.x           YES CONFIG up                    up
Ethernet0/1                x.x.x.x           YES CONFIG up                    up
Ethernet0/2                unassigned      YES unset administratively down down
Internal-Control0/0        127.0.1.1       YES unset up                    up
Internal-Data0/0           unassigned      YES unset up                    up
Management0/0              192.168.1.1     YES CONFIG up                    up
Please suggest what could be the reason.
Regards
Pankaj

Hi Ramraj,
Even i have the base license for my ASA 5510 which is showing all the 4 interfaces in sh ver. I don't think so license would be an issue. There should be some IOS code bug that needs to be upgraded. If this goes for an OS upgrade it should get resolved.
Its not showing up in sh ver . As Karsten said he might be running on old IOS version.
fy-a# sh ver
Cisco Adaptive Security Appliance Software Version 8.4(4)1
Device Manager Version 6.4(5)
Compiled on Thu 14-Jun-12 11:20 by builders
System image file is "disk0:/asa844-1-k8.bin"
Config file at boot was "startup-config"
fy-a up 1 day 1 hour
Hardware:   ASA5510, 1024 MB RAM, CPU Pentium 4 Celeron 1600 MHz
Internal ATA Compact Flash, 256MB
BIOS Flash M50FW016 @ 0xfff00000, 2048KB
Encryption hardware device : Cisco ASA-55x0 on-board accelerator (revision 0x0)
                             Boot microcode   : CN1000-MC-BOOT-2.00
                             SSL/IKE microcode: CNLite-MC-SSLm-PLUS-2.03
                             IPSec microcode : CNlite-MC-IPSECm-MAIN-2.06
                             Number of accelerators: 1
0: Ext: Ethernet0/0         : address is 2c54.2d0c.8f1a, irq 9
1: Ext: Ethernet0/1         : address is 2c54.2d0c.8f1b, irq 9
2: Ext: Ethernet0/2         : address is 2c54.2d0c.8f1c, irq 9
3: Ext: Ethernet0/3         : address is 2c54.2d0c.8f1d, irq 9
4: Ext: Management0/0       : address is 2c54.2d0c.8f1e, irq 11
5: Int: Not used            : irq 11
6: Int: Not used            : irq 5
Licensed features for this platform:
Maximum Physical Interfaces       : Unlimited      perpetual
Maximum VLANs                     : 50             perpetual
Inside Hosts                      : Unlimited      perpetual
Failover                          : Disabled       perpetual
VPN-DES                           : Enabled        perpetual
VPN-3DES-AES                      : Enabled        perpetual
Security Contexts                 : 0              perpetual
GTP/GPRS                          : Disabled       perpetual
AnyConnect Premium Peers          : 2              perpetual
AnyConnect Essentials             : Disabled       perpetual
Other VPN Peers                   : 250            perpetual
Total VPN Peers                   : 250            perpetual
Shared License                    : Disabled       perpetual
AnyConnect for Mobile             : Disabled       perpetual
AnyConnect for Cisco VPN Phone    : Disabled       perpetual
Advanced Endpoint Assessment      : Disabled       perpetual
UC Phone Proxy Sessions           : 2              perpetual
Total UC Proxy Sessions           : 2              perpetual
Botnet Traffic Filter             : Disabled       perpetual
Intercompany Media Engine         : Disabled       perpetual
This platform has a Base license.
Serial Number: JMX1AXXXXX
Running Permanent Activation Key: XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX
Configuration register is 0x1
Configuration has not been modified since last system restart.
fy-a#
Ramraj please do correct me if am wrong.
Please do rate if the given information helps.
By
Karthik

I am unable to see text after clicking on a pdf download.I just get a mid grey screen .I can send the pdf to my blackberry and see it -so the file is ok .I recently was at an official site that gave me an Adobe down load /update .Help please .

Why am I suddenly unable to see pdf (on iMac) when I click on them ?There is is just a mid grey blank screen .I have sent pdf to my Blackb and I can read it there ,so the file is OK .I recently tried to down load a recent version of Adobe reader from a government site -could this be the cause?If so ,how do I uninstall it ?

Back up all data.
Triple-click the line of text below to select it, the copy the selected text to the Clipboard (command-C):
/Library/Internet Plug-ins
In the Finder, select
Go ▹ Go to Folder
from the menu bar, or press the key combination shift-command-G. Paste (command-V) into the text box that opens, then press return.
From the folder that opens, remove any items that have the letters “PDF” in the name. You may be prompted for your login password. Then quit and relaunch Safari, and test.
I've seen an unconfirmed report that the "Silverlight" web plugin distributed by Microsoft can also interfere with PDF display in Safari, so you might need to remove it as well, if applicable.
If you still have the issue, repeat with this line:
~/Library/Internet Plug-ins
If you don’t like the results of this procedure, restore the items from the backup you made before you started. Relaunch Safari again.

Not able to to see interfaces after doing export import of the Business sys

Hi Gurus,
I am exporting an business system associated with CRM system from Dev system of XI 3.0 to dev PI 7.1 system client 500. After taking the export from XI 3.0 , when I import the business system in PI7.1 and associate it with the corresponding Technical system I am unbale to see the interface associate with the Business system. Thus I am having a problem of creating the Receiver Determination, Interface Determination etc in the Integration Directory of the PI 7.1 system. Can anyone suggets how to get the interfaces associated with the Business system....
Thanks
Regards
suk4023

Check if this blog helps you: /people/shabarish.vijayakumar/blog/2010/05/13/cant-find-interfaces-in-the-associated-business-system
Regards,
Abhishek.

Unable to see JSF pages in Design View after upgrade to Netbean 6.1

Hi:
I have a Sun Java Studio Creator Update 2 Project and I upgraded to Netbean 6.1 according to Sun's migration guide. It compiles and runs OK, but i can not see any page in design view at all.
Any one has any idea?
thanks

Hi Sriram,
I want to see commit stats on SM50 while background job runs. I unable to see on after upgrade.
all db stats are updated. On Sm50 screen unable to see Database commit count.
Cheers,
Harish

In my MacBook Pro, finder is crashing after logging in. It is showing crash report with Relaunch option, when i click on Relaunch option finder is working properly but i am unable to see top bar(Apple, Date, Wifi). Even in safari address bar not accepting

In my MacBook Pro(10.7.5), finder is crashing after logging in. It is showing crash report with Relaunch option, when i click on Relaunch option finder is working properly but i am unable to see Top bar(Apple logo, Date and Wifi etc... bar). Even in safari address bar, TextEdit not accepting any text means when type something not showing up and also i am unable operate any thing from keyboard. Plz help me…..

One thing that you can try is installing a 'fresh' version of OS X Lion. Boot into your Recovery partition (holding down the command and R keys whilst booting) and elect to install OS X from the Recovery screen. You need not erase your hard drive and you should not lose any of your data.
Oh, and just as a precaution, I would use Disk Utility, once you're in Recovery mode, to verify your hard drive before trying to install the OS again.
Clinton

This sign appeared in my account: "Your payment method was declined. Update your biiling info'. After adding new information about my others cards I see the same sign. Can't understand what the problem is and what should I do. Need help!!!

This sign appeared in my account: "Your payment method was declined. Update your biiling info'. After adding new information about my others cards I see the same sign. Can't understand what the problem is and what should I do. Everything used to be good before.
Do anyone know what I supposed to do in that situation?
Really need help!
Thanks in advance.

Contact iTunes Customer Service and request assistance
Use this Link > Apple Support iTunes Store Contact

Unable to see Active Directory Groups in the User Profile Database after Profile Import

***Major Update - I have finally been able to get the direct attention of the folks responsible for the User Profile Service on the SharePoint Product Team. Long story short, they have reproduced the error and identified as an actual mistake
that needs to be fixed, so it is now officially in the bug pipeline and will be fixed. The current estimate is some time in the summer. They will keep me updated with timeframes, which I am allowed to share as time goes on.
SharePoint Server 2010 Enterprise RTM. W2K8R2 w/multi-server setup:
AD/DNS
SQL 2008
WFE
APP
Claims Mode Web App only using Windows Integrated Auth
So, this was never a problem in 2007, and I didn't even realize it was a problem in 2010 until I started to build a solution that utilized my blog article:
InfoPath - User Roles in Browser-Enabled Forms Using AD Groups. I went to utilize the same web method of the same web service, but I noticed that no data was showing up at all. Typically,
the GetUserMembership/GetCommonMembership methods return the specified user's memberships: AD Security Groups, AD Distribution Lists, and SharePoint Sites (not SharePoint Groups, though).
My user profile sync is working. All AD users are pulled in with the proper profile data.
"Users and Groups" is selected in the Synchronization Entities section of my Sync Settings.
Security groups are working for permissions and audience targeting. Confirmed my users are affected properly by the use of Security Groups.
My query to the GetUserMemberships web method (and GetCommonMemberships) is running (not failing), but it's not returning anything even though my user is in some Security Groups and has explicit membership to multiple sites.
The GetUserProfileByName method of the same UserProfileService.asmx web service
returns all the regular profile data like expected, so the web service works and my profile database is populated
Basically, I'm not seeing my AD groups or any membership data populated in the profile database. I did use MIISCLIENT.exe to see what I could find, and here is what I saw:
Using the Metaverse Search, I searched for the "person" type and saw all of the users in my profile sync connection (single OU)
Using the same tool, I searched for the "group" type and saw nothing, but the message said 4 items were retrieved
I realized that the only column showing was displayName, and they were blank, so I added other columns to be sure
objectGUID, objectType, distinguishedName all showed values, and I could now see all the Security Groups from the OU where I'm doing my profile sync
My "person" objects all have displayNames showing but none of the groups do. In SharePoint, the GetUserMemberships method relies on displayName and accountName, but neither are coming through the profile import
So, it does seem like the groups are coming in with the profile import, but I can't see them. I also can't verify that the groups are being associated with my users in the profile database, because doing a query to the membership methods returns nothing...not
even blank rows.
***Edit: New information! Regular AD Distribution Lists _do_ work properly. I just never bothered testing them until folks on my blog notified me. DLs come through the profile sync, are visible in the profile database, and show up
when using the GetUserMemberships method.
***Edit: Ok, now we're getting somewhere. I checked my last profile sync with the MIISCLIENT, and this is what I found:
Here are the properties of my Distribution List:
Here are the properties of my Security Group:
Notice that the groupType value of the DL is a normal integer (2), but the groupType value of the SG is some crazy negative number. Both types are still lacking DisplayNames for some reason, but when I retrieve the DL via GetUserMemberships, it DOES
show the proper DisplayName despite nothing showing in the MIISCLIENT.
SharePoint Architect || Microsoft MVP ||
My Blog

Hello Clayton,
I have same problem with SP 2010 and now I am testing SP 2013 and seems that the problem still.aa
Probably I have some configuration problem, but all seems work, except this.
SharePoint 2013 has no improvements on this. Until seeing this thread, I thought it was an issue within my farm configuration or AD Service account for User Profile Sync. And I've dug far and wide for any other possible settings which would prevent users
from populating in the site people-picker. This might be flagged as off-topic, but I'll beg differ. How can I expect SharePoint to retrieve AD Users and Groups for accuracy in the sites which rely on this server??? Frustrating. I've spent hours and days on
this! I have 3 SP2013 farms with multiple clients (different OU's/containers and security groups). Testing in a separate QA DEV farm with the same config. NO luck yet!
This is where I'm at with it (posted this as a question recently on SharePoint Stack Exchange):
"Help.... Please.... Users from AD groups are not populating in the site people picker. I've set up a SharePoint 2013 site collection permissions group with only AD groups in it, no users added directly. Whether or not I give this SharePoint group permissions
to the site content, I still get none of the AD users showing up in the people picker. I have done the iisreset after adding the groups.
I've checked all of the people picker properties in stsadm to be sure there are no constraints in effect on the web app or site collections. User profiles are synching and I've tried both AD import and User Profile Sync. The AD groups are security
groups, though not email-enabled. The AD service account has all the special permissions. My web app is claims based. My app pool runs with Network Service account. No policies in place to restrict users, checked CA and the site collection settings.
What am I missing? I've read in multiple places that this is a supported/working config. So why can't I get these users to populate in people picker for things like Assigned To in a tasks list, or attendees of an event? "
There is some pretty good insight here, but no real hope:
User profile
synchronization: importing users and security groups in SharePoint 2010
Other Properties that I checked, before realizing this was an issue with the Profile Import...
stsadm -o getproperty -pn siteuseraccountdirectorypath -url https://URL
stsadm -o getproperty -propertyname peoplepicker-activedirectorysearchtimeout -url https://URL
stsadm -o getproperty -propertyname peoplepicker-distributionlistsearchdomains -url https://URL
stsadm -o getproperty -propertyname peoplepicker-nowindowsaccountsfornonwindowsauthenticationmode -url https://URL
stsadm -o getproperty -propertyname peoplepicker-onlysearchwithinsitecollection -url https://URL
stsadm -o getproperty -propertyname peoplepicker-searchadcustomfilter -url https://URL
stsadm -o getproperty -propertyname peoplepicker-searchadcustomquery -url https://URL
stsadm -o getproperty -propertyname peoplepicker-searchadforests -url https://URL
stsadm -o getproperty -propertyname peoplepicker-serviceaccountdirectorypaths -url https://URL
Hope we find a better answer, as it IS very misleading. User Profile Import specifies Users, or Users and Groups. Nothing is said about Containers or Distribution Groups, worse yet there lacks any clear disclosure about how "Groups" will not
actually import if they are a Global Security Group and the users contained within them exclusively will NOT be included in your profiles,
nor in any compiled Audiences. Which was another BIG bummer!
I'm hoping to see future improvements on the Group imports.

HT2188 Unable to see Wi-Fi status. After Settings General iTunes Wi-Fi Sync it displays "Sync will resume when R300764 AHWR001 is available". This has happened ever since I got my iPhone 3G 3 months ago. Any suggestions? Thanks

Unable to see Wi-Fi status after connecting to power source. After tapping Settings > General > iTunes Wi-Fi Sync, the message reads: Sync will resume when "R300764AHWR001" is available. Could someone tell me how to sync my iPhone 3G to ITunes, please? Thank you. Jan

iPhone 3G doesn't support Wi-Fi sync or IOS 5.1.1. You have to connect to iTunes using the dock connector to sync.
Unless you have a iPhone 3GS or jailbroken.

I am unable to see following SQL Server Analysis Services in central admin services after the SQL 2014 power pivot installations

I am unable to see following SQL Server Analysis Services in central admin services after the SQL 2014 power pivot installations
Ravi

Hi Ravi,
Per my knowledge, there is no Analysis Service in SharePoint.
After running the SQL 2014 setup to install PowerPivot for SharePoint, you need to open the PowerPivot for SharePoint 2013 Configuration tool in Central Admin Server and configure PowerPivot for SharePoint.
After that, you will see new Service Application called "Default PowerPivot Service Application" in Central Administration.
If you have other WFE servers, then you need to install the PowerPivot Add-In on all the other servers in the SharePoint farm.
More references:
http://sridharbabuk.blogspot.jp/2013/02/installing-configuring-analysis-service.html
http://msdn.microsoft.com/en-us/library/jj219067.aspx
Best regards.
Thanks
Victoria Xia
TechNet Community Support

After updating to the newest update when I type messages in Facebook or gmail I am unable to see at what am typing as I am unable to move the message up..is there a fix?

I Have updated to the newest update which is 8.1.2 after updating anytime I try to type up a message in Facebook or gmail I am unable to see my screen where I type my message, so am typing my messages blindly. Is there a fix for this?

The Split Keyboard feature may have been enabled accidentally when you updated.
If the keyboard is up on the middle of the screen, or covering text and the text is not moving up as expected - tap and hold down on the little keyboard and icon and select - Dock
You can turn the split keyboard off in Settings>General>Keyboard>Split Keyboard>Off.

I am unable to merge the call after adding in iphone 4 , can anybody help me ?

Unable to merge call for conference after adding new call . Can anybody help ?

Conference calls With GSM, you can set up a conference call with up to five people at a time, depending on your carrier.
Create a conference call: While on a call, tap Add Call, make another call, then tap Merge Calls. Repeat to add more people to the conference.
Drop one person: Tap Conference, tap next to a person, then tap End Call.
Talk privately with one person: Tap Conference, then tap Private next to the person. Tap Merge Calls to resume the conference.
Add an incoming caller: Tap Hold Call + Answer, then tap Merge Calls. Note: You can’t make a FaceTime video call when you’re on a conference call

Unable to see update iOS 7.1 even after many times install and reboot

Hi All,
I am unable to see my iPhone 4 updated with iOS7.1 even after multiple installs. I found this issue even with the previous version i7.0.X but ignored it as I was ok for going for an update then. But now I am keen to have iOS 7.1 as itseems it is giving performance improvements. Please help/suggest.

this is solved by connecting to itunes.. was not able to do via wifi..thanks all

I unable to see my network messages after upgrading to ios6 on my iphone4,can anyone help me for this issue?

I unable to see my network messages after upgrading to ios6 on my iphone4,can anyone help me for this issue?

Try to perform SMC and PRAM resets:
http://support.apple.com/kb/HT3964
http://support.apple.com/kb/ht1379
Then try a safe boot:
http://support.apple.com/kb/HT1564
Ciao.

WiSM, unable to see Interface after adding.

Similar Messages

Maybe you are looking for