WISM2 states
If it is possible to use two wism2 in two 6513 module in active and active state ? if there any license or something. or we can use it only in standby and active (i mean HA SSO), i think it could be better in load balancing, cause we can use on wism2 for some portion of ap, and second one to another portion
That is my preferred method, but that requires WLC with license. AP SSO doesn't allow for that.
Sent from Cisco Technical Support iPhone App
Similar Messages
-
WiSM2 with 7.4.110.0 & dhcp stats
Hi,
WiSM2 HA with 7.4.110.0 and DHCP proxy enabled. If we run "show dhcp stats" command, only the initially defined dynamic interfaces are showed. All dynamic interfaces are defined in the same way (only VLAN and related IP parameters are different, all interfaces has a external primary DHCP server asigned and proxy mode is global).
Any idea?
Thanks in advance.the gateway ip: 254.0.168.192 was an example.
the gateway ip I get with this configure is: 33.36.168.192
(Cisco Controller) show>interface detailed vlan107
Interface Name................................... vlan107
MAC Address...................................... c8:9c:1d:6a:81:80
IP Address....................................... 192.168.36.10
IP Netmask....................................... 255.255.255.0
IP Gateway....................................... 192.168.36.33
External NAT IP State............................ Disabled
External NAT IP Address.......................... 0.0.0.0
VLAN............................................. 107
Quarantine-vlan.................................. 0
NAS-Identifier................................... SR-WLC-1
Physical Port.................................... 1
DHCP Proxy Mode.................................. Global
Primary DHCP Server.............................. 192.168.250.12
Secondary DHCP Server............................ Unconfigured
DHCP Option 82................................... Disabled
ACL.............................................. Unconfigured
mDNS Profile Name................................ Unconfigured
AP Manager....................................... No
Guest Interface.................................. No
L2 Multicast..................................... Enabled -
AP name is not consistent in APs Join Stats.
hi all,
i have strange issue in my controller (WISM2) AP name is not consistent in APs Join Stats page while the naming is consistent in Wireless status page.as shown below.Thanks,
The problem solved after i cleared the access point from join AP stats. then restart it after that will join with normal name. -
Cisco AP 2702 can't join WiSM2 7.6.130.0
i got these msg log from AP. AP got ip address but can't discover WiSM2. other model 3502/2602 it's ok.
IOS Bootloader - Starting system.
flash is writable
Antigua Board
40MB format
Tide XL MB - 40MB of flash
Xmodem file system is available.
flashfs[0]: 13 files, 2 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 41158656
flashfs[0]: Bytes used: 6153216
flashfs[0]: Bytes available: 35005440
flashfs[0]: flashfs fsck took 9 seconds.
Base Ethernet MAC address: d4:6d:50:f9:eb:00
Ethernet speed is 100 Mb - FULL Duplex
Loading "flash:/ap3g2-rcvk9w8-mx/ap3g2-rcvk9w8-mx"...#########################
File "flash:/ap3g2-rcvk9w8-mx/ap3g2-rcvk9w8-mx" uncompressed and installed, entry point: 0x2003000
executing...
Secondary Bootloader - Starting system.
Antigua Board Pre-Pilot
40MB format
Tide XL MB - 40MB of flash
Xmodem file system is available.
flashfs[0]: 13 files, 2 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 41158656
flashfs[0]: Bytes used: 6153216
flashfs[0]: Bytes available: 35005440
flashfs[0]: flashfs fsck took 10 seconds.
flashfs[1]: 0 files, 1 directories
flashfs[1]: 0 orphaned files, 0 orphaned directories
flashfs[1]: Total bytes: 12257280
flashfs[1]: Bytes used: 1024
flashfs[1]: Bytes available: 12256256
flashfs[1]: flashfs fsck took 0 seconds.
Base Ethernet MAC address: d4:6d:50:f9:eb:00
Boot CMD: 'boot flash:/ap3g2-rcvk9w8-mx/ap3g2-rcvk9w8-xx;flash:/ap3g2-rcvk9w8-mx/ap3g2-rcvk9w8-xx'
Loading "flash:/ap3g2-rcvk9w8-mx/ap3g2-rcvk9w8-xx"...########################
File "flash:/ap3g2-rcvk9w8-mx/ap3g2-rcvk9w8-xx" uncompressed and installed, entry point: 0x1003000
executing...
Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706
Cisco IOS Software, C2700 Software (AP3G2-RCVK9W8-M), Version 15.3(3)JA, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2014 by Cisco Systems, Inc.
Compiled Fri 15-Aug-14 12:27 by prod_rel_team
Antigua Board Pre-Pilot
40MB format
Tide XL MB - 40MB of flash
Initializing flashfs...
flashfs[2]: 13 files, 2 directories
flashfs[2]: 0 orphaned files, 0 orphaned directories
flashfs[2]: Total bytes: 40900608
flashfs[2]: Bytes used: 6153216
flashfs[2]: Bytes available: 34747392
flashfs[2]: flashfs fsck took 11 seconds.
flashfs[2]: Initialization complete.
flashfs[3]: 0 files, 1 directories
flashfs[3]: 0 orphaned files, 0 orphaned directories
flashfs[3]: Total bytes: 11999232
flashfs[3]: Bytes used: 1024
flashfs[3]: Bytes available: 11998208
flashfs[3]: flashfs fsck took 0 seconds.
flashfs[3]: Initialization complete....done Initializing flashfs.
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
[email protected].
cisco AIR-CAP2702E-C-K9 (PowerPC) processor (revision A0) with 376810K/134656K bytes of memory.
Processor board ID FGL1849XBEM
PowerPC CPU at 800Mhz, revision number 0x2151
Last reset from power-on
LWAPP image version 8.0.72.236
1 Gigabit Ethernet interface
32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: D4:6D:50:F9:EB:00
Part Number : 73-15823-03
PCA Assembly Number : 000-00000-00
PCA Revision Number :
PCB Serial Number : FOC18474C56
Top Assembly Part Number : 800-41175-02
Top Assembly Serial Number : FGL1849XBEM
Top Revision Number : A0
Product/Model Number : AIR-CAP2702E-C-K9
% Please define a domain-name first.
ipv6 enable
^
% Invalid input detected at '^' marker.
ipv6 address autoconfig
^
% Invalid input detected at '^' marker.
ipv6 address dhcp
^
% Invalid input detected at '^' marker.
Press RETURN to get started!
*Mar 1 00:00:13.071: APAVC: Initial WLAN Buffers Given to System is 2500
*Mar 1 00:00:13.119: APAVC: WlanPAKs 42878 RadioPaks 42270
*Mar 1 00:00:13.119: Starting Ethernet promiscuous mode
*Mar 1 00:00:13.127: %LWAPP-3-CLIENTERRORLOG: Config load from flash failed. Initialising Cfg
*Mar 1 00:00:15.119: %LINK-6-UPDOWN: Interface GigabitEthernet0, changed state to up
*Mar 1 00:00:15.119: %LINK-6-UPDOWN: Interface GigabitEthernet1, changed state to up
*Mar 1 00:00:15.259: %SYS-5-RESTART: System restarted --
Cisco IOS Software, C2700 Software (AP3G2-RCVK9W8-M), Version 15.3(3)JA, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2014 by Cisco Systems, Inc.
Compiled Fri 15-Aug-14 12:27 by prod_rel_team
*Mar 1 00:00:15.295: %CDP_PD-4-POWER_OK: Full power - HIGH_POWER inline power source
*Mar 1 00:00:15.303: %LWAPP-3-CLIENTERRORLOG: Config load from flash failed. Initialising Cfg
lwapp_crypto_init: MIC Present and Parsed Successfully
*Mar 1 00:00:15.443: %SSH-5-ENABLED: SSH 2.0 has been enabled
*Mar 1 00:00:16.287: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, changed state to up
*Mar 1 00:00:20.083: DPAA Initialization Complete
*Mar 1 00:00:20.083: %SYS-3-HARIKARI: Process DPAA INIT top-level routine exited
*Mar 1 00:00:21.083: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0, changed state to up
*Mar 1 00:00:23.083: %LINK-6-UPDOWN: Interface BVI1, changed state to down
*Mar 1 00:00:24.083: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, changed state to down
*Mar 1 00:00:27.291: %LINK-6-UPDOWN: Interface BVI1, changed state to up
*Mar 1 00:00:28.291: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, changed state to up
*Mar 1 00:00:29.259: %DHCP-6-ADDRESS_ASSIGN: Interface BVI1 assigned DHCP address 10.201.1.184, mask 255.255.255.0, hostname APd46d.50f9.eb00
bridge-group 1 source-learning
^
% Invalid input detected at '^' marker.
%Default route without gateway, if not a point-to-point interface, may impact performance
*Mar 1 00:00:34.123: %LWAPP-3-CLIENTERRORLOG: Config load from flash failed. Initialising Cfg
%Error opening flash:/capwap-saved-config (No such file or directory)
APd46d.50f9.eb00#sh version
Cisco IOS Software, C2700 Software (AP3G2-RCVK9W8-M), Version 15.3(3)JA, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2014 by Cisco Systems, Inc.
Compiled Fri 15-Aug-14 12:27 by prod_rel_team
ROM: Bootstrap program is C2700 boot loader
BOOTLDR: C2700 Boot Loader (AP3G2-BOOT-M) LoaderVersion 15.2(4)JB5m, RELEASE SOFTWARE (fc2)
APd46d.50f9.eb00 uptime is 4 minutes
System returned to ROM by power-on
System image file is "flash:/ap3g2-rcvk9w8-mx/ap3g2-rcvk9w8-xx"
cisco AIR-CAP2702E-C-K9 (PowerPC) processor (revision A0) with 376810K/134656K bytes of memory.
Processor board ID FGL1849XBEM
PowerPC CPU at 800Mhz, revision number 0x2151
Last reset from power-on
LWAPP image version 8.0.72.236
1 Gigabit Ethernet interface
32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: D4:6D:50:F9:EB:00
Part Number : 73-15823-03
PCA Assembly Number : 000-00000-00
PCA Revision Number :
PCB Serial Number : FOC18474C56
Top Assembly Part Number : 800-41175-02
Top Assembly Serial Number : FGL1849XBEM
Top Revision Number : A0
Product/Model Number : AIR-CAP2702E-C-K9
Configuration register is 0xF
================
APd46d.50f9.eb00#show ip interface brief
Interface IP-Address OK? Method Status Protocol
BVI1 10.201.1.184 YES DHCP up up
GigabitEthernet0 unassigned NO unset up up
GigabitEthernet1 unassigned NO unset up down
===============
(WiSM-slot4-1) >show sysinfo
Manufacturer's Name.............................. Cisco Systems Inc.
Product Name..................................... Cisco Controller
Product Version.................................. 7.6.130.0
Bootloader Version............................... 1.0.16
Field Recovery Image Version..................... 7.0.43.32
Firmware Version................................. FPGA 1.6, Env 0.0, USB console 2.2
Build Type....................................... DATA + WPS
System Name...................................... WISM2
System Location..................................
System Contact...................................
System ObjectID.................................. 1.3.6.1.4.1.9.1.1293
Redundancy Mode.................................. Disabled
IP Address....................................... 10.201.255.250
Last Reset....................................... Software reset
System Up Time................................... 1 days 16 hrs 59 mins 28 secs
System Timezone Location......................... (GMT +8:00) HongKong, Bejing, Chongquing
System Stats Realtime Interval................... 5
System Stats Normal Interval..................... 180
Configured Country............................... MY - Malaysia
still got log:
Not in Bound state.
*Mar 1 02:59:49.139: %CAPWAP-3-DHCP_RENEW: Could not discover WLC. Either IP address is not assigned or assigned IP is wrong. Renewing DHCP IP.
*Mar 1 02:59:52.211: %DHCP-6-ADDRESS_ASSIGN: Interface BVI1 assigned DHCP address 10.201.1.184, mask 255.255.255.0, hostname APd46d.50f9.eb00
Not in Bound state.
*Mar 1 03:00:45.639: %CAPWAP-3-DHCP_RENEW: Could not discover WLC. Either IP address is not assigned or assigned IP is wrong. Renewing DHCP IP.
*Mar 1 03:00:48.711: %DHCP-6-ADDRESS_ASSIGN: Interface BVI1 assigned DHCP address 10.201.1.184, mask 255.255.255.0, hostname APd46d.50f9.eb00Hello
we had this problem too. I've figured out that the AP's which came factory preloaded with the
LWAPP image version
PRE { font-family: "Liberation Serif",serif; }P { margin-bottom: 0.08in; }
8.0.72.236 and 15.3(3) JA (without 1)
Version 15.3(3)JA
LWAPP image version 8.0.72.236
remained stuck on
*Mar 1 00:09:24.639: %CAPWAP-3-DHCP_RENEW: Could not discover WLC. Either IP address is not assigned or assigned IP is wrong. Renewing DHCP IP.
*Mar 1 00:09:28.735: %DHCP-6-ADDRESS_ASSIGN: Interface BVI1 assigned DHCP address 192.168.0.60, mask 255.255.255.0, hostname AP881d.fcaf.a71c
Not in Bound state.
*Mar 1 00:10:21.139: %CAPWAP-3-DHCP_RENEW: Could not discover WLC. Either IP address is not assigned or assigned IP is wrong. Renewing DHCP IP.######### ######### ip IP information
In our case we wanted to use the DNS Entry CISCO-CAPWAP-CONTROLLER.domain.name to discover the controller. As older APs (1240) were able to connect I tried with the recovery image (downloaded on Support)
15.3(3)JA1 containing
PRE { font-family: "Liberation Serif",serif; }P { margin-bottom: 0.08in; }
Version Suffix: k9w8-.153-3.JA1 8.0.110.0
Image Name: ap3g2-k9w8-mx.153-3.JA1
Version Directory: ap3g2-k9w8-mx.153-3.JA1
Ios Image Size: 11407872
Total Image Size: 13496832
Image Feature: WIRELESS LAN|LWAPP
Image Family: AP3G2
Wireless Switch Management Version: 8.0.110.0
with this image the AP could join the Controller via DNS.
So If you have an AP preloaded with Image 15.3.JA (without 1) try this:
ping CISCO-CAPWAP-CONTROLLER.localdomain as stated by mykhuzaimi above
OR
capwap ap controller ip address <IP-address> as stated by mykhuzaim above
set option 43
Load image ap3g2-rcvk9w8-tar.153-3.JA1.tar
Unfortunately all workaround require manual interventions......
Saluti Mauro -
AP SSO WISM2 WLC 7.4.121
HI everyone,
I'm currently doing a proof of concept on the AP SSO feature running on WLC 7.4.121.
The first thing I would like be sure is that client SSO is not avalaible in 7.4.X release, i need to upgarde to 7.5.X, Am I right ?
The second thing I would like to share and investigate with you is about AP SSO not currently working in my topology.
I have 2 seperate C6500 (SUP720-3B) switches with 1 WISM2 in each and both switches interconnected trough a 10G port.
I enable AP SSO on both WLC that synchronize themselves trough the 10G port on a special redundancy VLAN.
They both synchronize, and everything is working (both AP database on primary and standby WLC).
What I can't understand is when forcing switchover on the primary (redundancy force-switchover command), the fallback is doing great to the standby WLC but the AP still get into CAPWAP DISCOVER state because of a timeout with the following logging message
*Feb 14 15:36:37.727: %CAPWAP-3-ERRORLOG: Sequence number (0) mismatch in request messageDeleting clients for centrally switched wlan 1Deleting clients for centrally switched wlan 1Sending hreap clients to wlc on HA eventAP1cdf.0f66.90b4#% Cannot enable CDP on this interface, since CDP is not running% Cannot enable CDP on this interface, since CDP is not running., 5)14 15:37:22.934: %CAPWAP-3-ERRORLOG: Retransmission count for packet exceeded max(CAPWAP_WTP_EVENT_REQUEST*Feb 14 15:37:22.934: %CAPWAP-3-ERRORLOG: GOING BACK TO DISCOVER MODE
So the SSID is unavalaible for a certain period of time as it would be with N+1 redundancy.
I also saw that some documentation said that tle WLC needs to be run on a VSS (
http://www.cisco.com/c/en/us/support/docs/wireless/5500-series-wireless-controllers/113681-high-availability-dg-00.html) and some other say the contrary (http://www.cisco.com/c/en/us/products/collateral/wireless/aironet-1130-ag-series/qa_c67-714540.html)
Did you manage to get AP SSO working and did you ever have this issue ?
Thank for you help !HI Max,
The first thing I would like be sure is that client SSO is not avalaible in 7.4.X release, i need to upgarde to 7.5.X, Am I right ?The second thing I would like to share and investigate with you is about AP SSO not currently working in my topology.
Yes you need 7.5 version on WLC for Client SSO.
I never seen this tiype of error, You must contatc TAC and tell them about this issue.
Regards
Dont forget to rate helpful posts -
After enable HA, both WISM2 modules are stay in Maintanance mode.
How can I undo this state.That is a known bug. Have you tried power cycling the WiSM2 modules? You have to maybe shut one down or both to get it out of maintenance mode. I know you have to remove AP SSO also and then re-enable that again. There isn't a good way to do it without powering down the WiSM2.
Sent from Cisco Technical Support iPhone App -
CAPWAP messages WISM2 7.5.102
Hi.
I have a question about a CAPWAP messages in my trap logs after upgrading my WISM2 to 7.5.102.
AP "xxxxxx", MAC: 34...... disassoiated previously due to Link Failure Uptime 4 days , 10 h... Reason: Capwap WTP Event request
My AP environment is 1142N attached thru WS-2960S switches. This message was not in my traplogs before upgarding to 7.5.102.
The switch and WAN environment is the same as before upgarding.
Thanks for any tips.
Regards
Johan LindstrandHi,
Thanks for you reply. I´m not sure if my radio stuck, what looks for me that AP lose conectivity for a brief moment with WLC and then recovery connectivity (flapping).
I have APs(same model) at same site without issues, and APs (same model) in others site with same behavior.
AP model LAP1141N
Below logs are from AP reboot process... however joining erros occurs several times during the day... and association time with controller keeps reseting (example: AP up time 1d / association time 15 min).
That instability to AP association creates WLAN instability, because my authentication is central.
*Mar 1 00:12:38.693: %CAPWAP-3-ERRORLOG: Selected MWAR 'WLC01'(index 0).
*Mar 1 00:12:38.693: %CAPWAP-3-ERRORLOG: Go join a capwap controller
*Dec 20 14:16:42.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 192.168.1.1 peer_port: 5246
*Dec 20 14:16:42.776: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 192.168.1.1 peer_port: 5246
*Dec 20 14:16:42.777: %CAPWAP-5-SENDJOIN: sending Join Request to 192.168.1.1
*Dec 20 14:16:42.786: %CAPWAP-3-ERRORLOG: Invalid event 10 & state 5 combination.
*Dec 20 14:16:42.786: %CAPWAP-3-ERRORLOG: CAPWAP SM handler: Failed to process message type 10 state 5.
*Dec 20 14:16:42.787: %CAPWAP-3-ERRORLOG: Failed to handle capwap control message from controller
*Dec 20 14:16:42.787: %CAPWAP-3-ERRORLOG: Failed to process encrypted capwap packet from 192.168.1.1
*Dec 20 14:16:42.897: Starting Ethernet promiscuous mode
*Dec 20 14:16:43.202: %LWAPP-4-CLIENTEVENTLOG: OfficeExtend Localssid saved in AP flash
*Dec 20 14:16:43.294: ac_first_hop_mac - IP:10.8.2.136 Hop IP:10.8.2.136 IDB:BVI1
*Dec 20 14:16:44.555: %CAPWAP-5-JOINEDCONTROLLER: AP has joined controller WLC01 -
Cisco 3502i AP operation status in downloading in controller wism2
Hello folks,
I have an issue with two APs (3502i) which is associated to controller wism2. Total number of APs are connected to this controller is 422 and once I added two new APs (3502i) to this controller I am unable to see these APs coming up. Getting error messages like wrong primary controller nad secondary controller. When I loggedin to the controller through CLI following are the details I am getting for the APs which is not registering to the controller:, Also for comparison I am attaching the statistics for the AP which is working good and is able to register.
Note: I thought the problem with these two APs and will try replacing them but when i connected the other two APs to different switch and different subnet the same errors we are seeing. This is something urgent to fix and need your assitance to fix this at the earliest. Please let me know if more information needed.
ISSUE with the AP:
show ap config general AB2-4N-AP11
Cisco AP Identifier.............................. 440
Cisco AP Name.................................... AB2-4N-AP11
Country code..................................... US - United States
Regulatory Domain allowed by Country............. 802.11bg:-A 802.11a:-A
AP Country code.................................. -
AP Regulatory Domain............................. Unconfigured
Switch Port Number .............................. 13
MAC Address...................................... 28:94:0f:c9:03:3c
IP Address Configuration......................... DHCP
IP Address....................................... Disabled
Telnet State..................................... Disabled
Ssh State........................................ Disabled
Cisco AP Location................................ AB 2 - Ctrl1/2
Cisco AP Group Name.............................. AB2-3-4
Primary Cisco Switch Name........................ us-ab1-wifi-ctrl1
Primary Cisco Switch IP Address.................. 10.200.44.102
Secondary Cisco Switch Name...................... us-cd3-wifi-ctrl1
Secondary Cisco Switch IP Address................ 10.200.45.102
Tertiary Cisco Switch Name.......................
Tertiary Cisco Switch IP Address................. Not Configured
Administrative State ............................ ADMIN_ENABLED
--More-- or (q)uit
Operation State ................................. DOWNLOADING
Mirroring Mode .................................. Disabled
AP Mode ......................................... Local
Public Safety ................................... Disabled
AP SubMode ...................................... Not Configured
Remote AP Debug ................................. Disabled
Logging trap severity level ..................... informational
Logging syslog facility ......................... kern
S/W Version .................................... 7.2.103.0
Boot Version ................................... 12.4.23.0
Mini IOS Version ................................ 0.0.0.0
Stats Reporting Period .......................... 180
LED State........................................ Disabled
PoE Pre-Standard Switch.......................... Enabled
PoE Power Injector MAC Addr...................... Disabled
Power Type/Mode.................................. Power injector / Normal mode
Number Of Slots.................................. 2
AP Model......................................... AIR-CAP3502I-A-K9
AP Serial Number................................. FTX1602K7LT
AP Certificate Type.............................. Manufacture Installed
AP User Mode..................................... Not Configured
AP User Name..................................... Not Configured
AP Dot1x User Mode............................... Not Configured
--More-- or (q)uit
AP Dot1x User Name............................... Not Configured
Cisco AP system logging host..................... 255.255.255.255
Ethernet Port Duplex............................. Auto
Ethernet Port Speed.............................. Auto
AP Link Latency.................................. Disabled
Rogue Detection.................................. Enabled
AP TCP MSS Adjust................................ Disabled
Good AP for comparison:
show ap config general IL2-4N-AP10
Cisco AP Identifier.............................. 260
Cisco AP Name.................................... AB2-4N-AP10
Country code..................................... US - United States
Regulatory Domain allowed by Country............. 802.11bg:-A 802.11a:-A
AP Country code.................................. US - United States
AP Regulatory Domain............................. 802.11bg:-A 802.11a:-A
Switch Port Number .............................. 13
MAC Address...................................... f8:66:f2:67:69:e5
IP Address Configuration......................... DHCP
IP Address....................................... 10.36.2.70
IP NetMask....................................... 255.255.255.0
Gateway IP Addr.................................. 10.36.2.1
NAT External IP Address.......................... None
CAPWAP Path MTU.................................. 1485
Telnet State..................................... Disabled
Ssh State........................................ Disabled
Cisco AP Location................................ AB 2 - Ctrl1/2
Cisco AP Group Name.............................. AB2-3-4
Primary Cisco Switch Name........................ us-ab1-wifi-ctrl1
Primary Cisco Switch IP Address.................. 10.200.44.102
Secondary Cisco Switch Name...................... us-cd3-wifi-ctrl1
--More-- or (q)uit
Secondary Cisco Switch IP Address................ 10.200.45.102
Tertiary Cisco Switch Name.......................
Tertiary Cisco Switch IP Address................. Not Configured
Administrative State ............................ ADMIN_ENABLED
Operation State ................................. REGISTERED
Mirroring Mode .................................. Disabled
AP Mode ......................................... Local
Public Safety ................................... Disabled
AP SubMode ...................................... Not Configured
Remote AP Debug ................................. Disabled
Logging trap severity level ..................... informational
Logging syslog facility ......................... kern
S/W Version .................................... 7.0.116.0
Boot Version ................................... 12.4.23.0
Mini IOS Version ................................ 7.0.94.21
Stats Reporting Period .......................... 180
LED State........................................ Enabled
PoE Pre-Standard Switch.......................... Disabled
PoE Power Injector MAC Addr...................... Disabled
Power Type/Mode.................................. Power injector / Normal mode
Number Of Slots.................................. 2
AP Model......................................... AIR-CAP3502I-A-K9
AP Image......................................... C3500-K9W8-M
--More-- or (q)uit
IOS Version...................................... 12.4(23c)JA2
Reset Button..................................... Enabled
AP Serial Number................................. FTX1432S2F5
AP Certificate Type.............................. Manufacture Installed
AP User Mode..................................... AUTOMATIC
AP User Name..................................... Not Configured
AP Dot1x User Mode............................... Not Configured
AP Dot1x User Name............................... Not Configured
Cisco AP system logging host..................... 255.255.255.255
AP Up Time....................................... 31 days, 04 h 58 m 37 s
AP LWAPP Up Time................................. 4 days, 11 h 24 m 23 s
Join Date and Time............................... Wed Jun 20 23:36:59 2012
Join Taken Time.................................. 0 days, 00 h 00 m 11 s
Ethernet Port Duplex............................. Auto
Ethernet Port Speed.............................. Auto
AP Link Latency.................................. Disabled
Rogue Detection.................................. Enabled
AP TCP MSS Adjust................................ Disabled
Thanks,
AhmedThe new Cisco 3500 WAP (S/N: FTX1602K7LT) is running WLC version 7.2.103.0 but the older one (S/N: FTX1432S2F5) is running WLC version 7.0.116.0.
You could try by consoling into the new WAP and deleting the CAPWAP image and leave the RCV image alone. -
And/or if statement in rtf templates.
Hi all,
I'm using XML Publisher 4.5.
I have created a word template file (rtf) for my reports. I need to be able to show some content in the template file by using and and/or if statement.
fx. <?if:doc_type='STANDARD'?> OR <?if:doc_type='DEFAULT'?>
How can I do this?
In advance thank you.
Best regards
KennethHi D,
Thank you for your answer.
I have seriously thought about that solution; but I don't think it's a smart way to do it.
If i do it like that, i need to copy the whole table and paste it inside the if statements.
I have two xml elements that I need to make the decisions on. POH_PO_TYPE & CP_RELEASE_NUM.
POH_PO_TYPE can be: STANDARD, RELEASE or BLANKET.
CP_RELEASE_NUM can be: '' or N
If POH_PO_TYPE is RELEASE AND CP_RELEASE_NUM is not ''
OR POH_PO_TYPE is STANDARD
OR POH_PO_TYPE is BLANKET AND CP_RELEASE_NUM is ''
THEN show table (which contains the whole PO).
It shall show the content of the PO in any of these cases.
BR Kenneth -
Hi srinivas bobbala,
Thank you for your response.But I think my quesition was not clear.My ques... is for suppose there is one datafile for importing like.. "datafile_21" Here my intention is it takes file from datafile_21 only but it appears in import statement like datafile_21<<curmon>>.
import database sample.sample data from data_file "c:\\ABC\datafile_21_AUG.txt" using server rules_file datafile on error abort;
In this it takes datafile from datafile_21.But it appears like datafile_21_AUG in import statement.This AUG coming from batch file.
Essmsh c:\\ABC\loadmxl.mxl %curmon%No it is not possible.
I assume the data file "datafile_21" is first renamed to datafile_21_${CurrMth} in the batchscript.
After that this data file *datafile_21_${CurrMth}* is pointed in the import statement.
In the logs you will see this file as datafile_21_Aug. -
Help with if statement in cursor and for loop to get output
I have the following cursor and and want to use if else statement to get the output. The cursor is working fine. What i need help with is how to use and if else statement to only get the folderrsn that have not been updated in the last 30 days. If you look at the talbe below my select statement is showing folderrs 291631 was updated only 4 days ago and folderrsn 322160 was also updated 4 days ago.
I do not want these two to appear in my result set. So i need to use if else so that my result only shows all folderrsn that havenot been updated in the last 30 days.
Here is my cursor:
/*Cursor for Email procedure. It is working Shows userid and the string
You need to update these folders*/
DECLARE
a_user varchar2(200) := null;
v_assigneduser varchar2(20);
v_folderrsn varchar2(200);
v_emailaddress varchar2(60);
v_subject varchar2(200);
Cursor c IS
SELECT assigneduser, vu.emailaddress, f.folderrsn, trunc(f.indate) AS "IN DATE",
MAX (trunc(fpa.attemptdate)) AS "LAST UPDATE",
trunc(sysdate) - MAX (trunc(fpa.attemptdate)) AS "DAYS PAST"
--MAX (TRUNC (fpa.attemptdate)) - TRUNC (f.indate) AS "NUMBER OF DAYS"
FROM folder f, folderprocess fp, validuser vu, folderprocessattempt fpa
WHERE f.foldertype = 'HJ'
AND f.statuscode NOT IN (20, 40)
AND f.folderrsn = fp.folderrsn
AND fp.processrsn = fpa.processrsn
AND vu.userid = fp.assigneduser
AND vu.statuscode = 1
GROUP BY assigneduser, vu.emailaddress, f.folderrsn, f.indate
ORDER BY fp.assigneduser;
BEGIN
FOR c1 IN c LOOP
IF (c1.assigneduser = v_assigneduser) THEN
dbms_output.put_line(' ' || c1.folderrsn);
else
dbms_output.put(c1.assigneduser ||': ' || 'Overdue Folders:You need to update these folders: Folderrsn: '||c1.folderrsn);
END IF;
a_user := c1.assigneduser;
v_assigneduser := c1.assigneduser;
v_folderrsn := c1.folderrsn;
v_emailaddress := c1.emailaddress;
v_subject := 'Subject: Project for';
END LOOP;
END;
The reason I have included the folowing table is that I want you to see the output from the select statement. that way you can help me do the if statement in the above cursor so that the result will look like this:
emailaddress
Subject: 'Project for ' || V_email || 'not updated in the last 30 days'
v_folderrsn
v_folderrsn
etc
[email protected]......
Subject: 'Project for: ' Jim...'not updated in the last 30 days'
284087
292709
[email protected].....
Subject: 'Project for: ' Kim...'not updated in the last 30 days'
185083
190121
190132
190133
190159
190237
284109
286647
294631
322922
[email protected]....
Subject: 'Project for: Joe...'not updated in the last 30 days'
183332
183336
[email protected]......
Subject: 'Project for: Sam...'not updated in the last 30 days'
183876
183877
183879
183880
183881
183882
183883
183884
183886
183887
183888
This table is to shwo you the select statement output. I want to eliminnate the two days that that are less than 30 days since the last update in the last column.
Assigneduser....Email.........Folderrsn...........indate.............maxattemptdate...days past since last update
JIM......... jim@ aol.com.... 284087............. 9/28/2006.......10/5/2006...........690
JIM......... jim@ aol.com.... 292709............. 3/20/2007.......3/28/2007............516
KIM......... kim@ aol.com.... 185083............. 8/31/2004.......2/9/2006............. 928
KIM...........kim@ aol.com.... 190121............. 2/9/2006.........2/9/2006.............928
KIM...........kim@ aol.com.... 190132............. 2/9/2006.........2/9/2006.............928
KIM...........kim@ aol.com.... 190133............. 2/9/2006.........2/9/2006.............928
KIM...........kim@ aol.com.... 190159............. 2/13/2006.......2/14/2006............923
KIM...........kim@ aol.com.... 190237............. 2/23/2006.......2/23/2006............914
KIM...........kim@ aol.com.... 284109............. 9/28/2006.......9/28/2006............697
KIM...........kim@ aol.com.... 286647............. 11/7/2006.......12/5/2006............629
KIM...........kim@ aol.com.... 294631............. 4/2/2007.........3/4/2008.............174
KIM...........kim@ aol.com.... 322922............. 7/29/2008.......7/29/2008............27
JOE...........joe@ aol.com.... 183332............. 1/28/2004.......4/23/2004............1585
JOE...........joe@ aol.com.... 183336............. 1/28/2004.......3/9/2004.............1630
SAM...........sam@ aol.com....183876.............3/5/2004.........3/8/2004.............1631
SAM...........sam@ aol.com....183877.............3/5/2004.........3/8/2004.............1631
SAM...........sam@ aol.com....183879.............3/5/2004.........3/8/2004.............1631
SAM...........sam@ aol.com....183880.............3/5/2004.........3/8/2004.............1631
SAM...........sam@ aol.com....183881.............3/5/2004.........3/8/2004.............1631
SAM...........sam@ aol.com....183882.............3/5/2004.........3/8/2004.............1631
SAM...........sam@ aol.com....183883.............3/5/2004.........3/8/2004.............1631
SAM...........sam@ aol.com....183884.............3/5/2004.........3/8/2004............ 1631
SAM...........sam@ aol.com....183886.............3/5/2004.........3/8/2004............ 1631
SAM...........sam@ aol.com....183887.............3/5/2004.........3/8/2004............ 1631
SAM...........sam@ aol.com....183888.............3/5/2004.........3/8/2004............ 1631
PAT...........pat@ aol.com.....291630.............2/23/2007.......7/8/2008............ 48
PAT...........pat@ aol.com.....313990.............2/27/2008.......7/28/2008............28
NED...........ned@ aol.com.....190681.............4/4/2006........8/10/2006............746
NED...........ned@ aol.com......95467.............6/14/2006.......11/6/2006............658
NED...........ned@ aol.com......286688.............11/8/2006.......10/3/2007............327
NED...........ned@ aol.com.....291631.............2/23/2007.......8/21/2008............4
NED...........ned@ aol.com.....292111.............3/7/2007.........2/26/2008............181
NED...........ned@ aol.com.....292410.............3/15/2007.......7/22/2008............34
NED...........ned@ aol.com.....299410.............6/27/2007.......2/27/2008............180
NED...........ned@ aol.com.....303790.............9/19/2007.......9/19/2007............341
NED...........ned@ aol.com.....304268.............9/24/2007.......3/3/2008............ 175
NED...........ned@ aol.com.....308228.............12/6/2007.......12/6/2007............263
NED...........ned@ aol.com.....316689.............3/19/2008.......3/19/2008............159
NED...........ned@ aol.com.....316789.............3/20/2008.......3/20/2008............158
NED...........ned@ aol.com.....317528.............3/25/2008.......3/25/2008............153
NED...........ned@ aol.com.....321476.............6/4/2008.........6/17/2008............69
NED...........ned@ aol.com.....322160.............7/3/2008.........8/21/2008............4
MOE...........moe@ aol.com.....184169.............4/5/2004.......12/5/2006............629
[email protected]/27/2004.......3/8/2004............1631
How do I incorporate a if else statement in the above cursor so the two days less than 30 days since last update are not returned. I do not want to send email if the project have been updated within the last 30 days.
Edited by: user4653174 on Aug 25, 2008 2:40 PManalytical functions: http://download-west.oracle.com/docs/cd/B10501_01/server.920/a96540/functions2a.htm#81409
CASE
http://download.oracle.com/docs/cd/B10501_01/appdev.920/a96624/02_funds.htm#36899
http://download.oracle.com/docs/cd/B10501_01/appdev.920/a96624/04_struc.htm#5997
Incorporating either of these into your query should assist you in returning the desired results. -
I have a Y9 Computer Science Exam next week and I know that this will probably be one of the questions on it so I need to know the answer. What is the difference?
An If statement executes once IF the statement is true:
If 1 = 2/2 Then
Textwindow.writeline("True")
EndIf
A While statement executes WHILE the statement is true:
While 4 = 2+2
'Will keep looping while it is true
EndWhile
A For statement loops a number in increment:
For i = 1 to 10
'Every time through, i gets bigger by one until it equals 10
EndFor
It is written: "'As surely as I live,' says the Lord, 'every knee will bow before me; every tongue will acknowledge God.'" Romans 14:11 -
regarding the following sql:
SELECT a.lname, a.fname, a.user_id, c.address, c.city,
c.zip, c.addresstypeid, d.descriptor as state
FROM users a, address c, maintstatetype d
WHERE a.user_id = c.user_id(+)
AND c.statetypeid = d.statetypeid(+)
AND c.addresstypeid in (1,2,3,4)
I have a database of users and addresses. Each user can
have multiple addresses and the addresses are
designated by addresstypeid. In plain english, what I want
to pull is "If they have an addresstypeid of 1, pull that one
only, if not, check if they have a 2 and use that, if not, check
for a 3, etc..".
Any help with this?What you want, then, is to pull the address with the minimum addresstypeid ..
SELECT a.lname, a.fname, a.user_id, c.address, c.city,
c.zip, c.addresstypeid, d.descriptor as state
FROM users a, address c, maintstatetype d
WHERE a.user_id = c.user_id(+)
AND c.statetypeid = d.statetypeid(+)
AND c.addresstypeid =
(select min(c2.addresstypeid)
from address c2
where c2.userid=a.userid
I'm not sure what this will do to your outerjoin, though. You might have to get funky with a union ...
SELECT a.lname, a.fname, a.user_id, c.address, c.city,
c.zip, c.addresstypeid, d.descriptor as state
FROM users a, address c, maintstatetype d
WHERE a.user_id = c.user_id
AND c.statetypeid = d.statetypeid
AND c.addresstypeid =
(select min(c2.addresstypeid)
from address c2
where c2.userid=a.userid
Union all
SELECT a.lname, a.fname, a.user_id, to_char(null), to_char(null),
to_char(null), to_char(null), to_char(null)
FROM users a
WHERE not exists
(select 1
from address c
where c.userid=a.userid
) -
'IF' statement in a select statment?
I have the following cursor in a package specification;
cursor c_sales_code is
select sales_condition||' MC '||sales_option
from sales;This will return something like: 'T300 MC 9'
MC means 'multiple choice' for when there are multiple options. Although, sales_option is sometimes null and in this case I just want 'T300' to be returned, not 'T300 MC'.
How would I go about doing this?
Thanks,
fakelvisUse
CASE and DECODE
to add the functoinality of Conditional Statements in Your SQL Statements..
These two CASE / DECODE will help you to get your desired output -
I need to choose between value1 and value2 within a select statement.
TableA
Flag (char)
Value1
Value2
ItemDesc
pseudo code
select ItemDesc, (if Flag = 'y' then Value1 else Value2) as Price from TableA;
How can this be done?select itemdesc,
sum (case
when flag = 'y'
then (case
when value1 < 10
then value1 * 1.2
else value1
end)
else value2
end
) as price
from tablea
group by itemdesc;
Maybe you are looking for
-
How to get keynote presentation to play all day on apple tv via iPad
Hello, I currently have an iPad (1st Gen iPad Mini) at my shop that I would like to use for playing a keynote presentation in my lobby throughout the day. My presentation plays on a loop about 5 or 6 times then keynote shuts down. Any ideas on what I
-
IE 9 incorrectly encoding Unicode characters in URIs to ISO-8859-1 instead of UTF8
Lets take the example word präsentation In Firefox, if I specify that as a CGI parameter, on the receiving end, I recieve: pr\\303\\244sentation which decoded as UTF-8 gives me: pr{U+00E4}sentation or my submitted word präsentation. What does IE give
-
Why is my itunes in THAI language? how do i set it back to english ?
why is my itunes in THAI language? how do i set it back to english ? thanks !
-
please explain the process of getting back my default apps.... Moderator's note: We have provided a subject-related title to help other forum users easily view and respond to this post.
-
Hi, I am trying to achieve something like"Column Labels" in the below link http://www.flexmonster.com/flash/help/index.html?file=Examples/sample_flex/FlexPivot.html I tried using collapsible panel concept but the when the panel opens it is of limited