WITEM GOIN TWICE TO THE FIRST APPROVER for SC APPROVAL

Hello All,
I have implemented the N-level Workflow WS14000133 through the BBP_WFL_APPROV_BADI for SC appropval...now my pro is that teh Witem goes to the first approver twice.....Has anybody come across this????
Currently i have hardcoded the value for Approvers .
Regards,
Disha.

Hi Disha,
I am having the same issue. Can you please let me know if you have resolved it.
Workitem status shows as approved, but it adds the same approver again.
Regards,
Ram.

Similar Messages

How to set up Airport Extreme with Charter ARRIS Modem TM902A for the first time for WIRELESS.

How to set up Airport Extreme with Charter ARRIS Modem TM902A for the first time for WIRELESS.
When Charter Tech goes to your site, have them connect the modem up, but do not connect the modem to your iMAC or MacBook Pro. What you want to do is connect the Airport Extreme to the iMac or MacBook Pro first with the Ethernet Cable. You have to do this to configure via Airport Utility to set up the Base Station Name & Base Station Password.
You will then create/configure a Wireless Network, create your Wireless Password that will be entered on each of your Devices, example, Apple Tv, your iPhone, etc., you want to allow access to your Wireless Network you are creating.
Wireless Security will be -> WPA/WPA2 personal or just WPA2
Enter the Wireless Password you want
Verify the Wireless Password (enter it again)
After it is created you will see it on the Airport Utility window with the name you created for it and to the left, will be a Dot (circle that will be yellow).
Next you then want to unplug the power to the Airport Extreme, and then take the end of the Ethernet cable you unplugged from the iMac or Lap top MacBook Pro and connect it to the back of the Modem.
Next unplug the power cord from the modem and wait about 5 minutes, then plug the power back into the Arris Modem and wait until all lights come back on the modem wait
about 5 minutes, then plug the power cord back to the Airport Extreme and you will see it the light blinking yellow. Wait about 5 to 10 minutes, during this time Restart you IMAC or MacBook Pro, and once it is back up click on the Airport Utility and you should see on the Airport Utility screen.
For INTERNET to the left the light should be green and you should see the Airport Extreme also appear and the light to the left on the screen should also be green. If they are, you then should be able to click on the Wireless Symbol on top of bar of the screen and click to select the Wireless Network Name you created.
If you Do Not See the light (Icon) next to INTERNET turn Green, or if you see the Internet Light Green, but the Light (Icon) next to the Airport Extreme is yellow, unplug the power again to the modem and unplug the power again to the Airport extreme and wait about 15 minutes or up to 30 minutes. Then plug the power cord back to the modem wait till all the lights light up then, plug the power cord back into the Airport Extreme and Restart your iMAC or MacBook Pro.
The Airport Extreme light should change from yellow to green. Open up the Airport Utility to see what the indicators are showing they should both be green. Again select Wireless network you created under the Wireless Icon on the top right of the screen. Open Safari and see if you are able to Route to a web page or the apple site should appear.
WHAT TO DO IF YOUR AIRPORT EXTREME WAS PREVIOUSLY SET UP FOR USE WITH ANOTHER CARRIERS ROUTER OR MODEM.
NOTE: If you already had your Airport Extreme connected for example, I previously had ATT Uverse and the Airport Extreme was connected to the Wireless Router Model 3801HGV, I disabled the Uverse Wireless and used the Airport Extreme for the Wireless signal in bridge mode, as the Airport extreme Signal is much stronger than the Uverse router, and I was able to obtain a Wireless signal with the Airport Extreme way much better with no signal loss which was very very frustrating with the Uverse router.
Anyhow if you had it hooked up like this, now that you will be using it with the Charter ARRIS Modem TM902A, you will need to reset the Airport Extreme to clear out the old data it has in memory, with the previous set up otherwise it will not work. Trust me I spent 6 hours trying to make it work reading all Apple Support Community questions and answers relating to this type issue/problem others have been having trying to get their set up working. I tried all the tips, and I finally decided just to see if by chance I would be able to connect with someone with Charter Tech support who might be familiar with Apple to be able to assist me and by luck I did. He told me why it was not working and was all due the previous configuration with the ATT Uverse router was still in memory with the Airport Extreme. Finally it was 10:30 PM when I decided to call Charter Tech Support and I had been working on this since 3:00 pm pacific. I did not call them earlier as all the post I read said they never received any good help from Charter. After calling them I finished up by 11:00 PM and was able to finally connect Apple Tv, iMac, iPhones and Macbook Pro. We love our Apple Product and Happy all is connected with the new
Internet Provider Charter. I must say the speed is way way much better than it ever was with AT&T Uverse.
THIS IS WHAT YOU WILL NEED TO DO:
First you will need to unplug the Airport Extreme, then by taking the tip of a pen or paper clip end you need to push the reset button on the back of the Airport Extreme and hold it
down and at the same time plug the power cord back into the Airport Extreme count to 5 or 10 then release the reset button. Then once he light in front of the Airport Extreme stops blinking you need to plug the Ethernet cable from the Airport Extreme to your iMAC or Macbook Pro, and restart which ever one you have, then open the Airport Utility once it is back up. If you see airport extreme pop up with the old network name or it shows and yellow triangle click on the Airport Extreme ICON it will not let you configure it but will ask if you want to get rid of it or remove and just do it. Then Again restart your iMAC or MacBook Pro, open up Airport Utility again, and on the top left you should see under “Other Airport Base Stations” the MAC ID for the Airport Extreme.
You will then create/configure a Wireless Network, create your Wireless Password that will be entered on each of your Devices, example, Apple TV, your iPhone, etc., you want to allow access to your Wireless Network you are creating.
Wireless Security will be -> WPA/WPA2 personal or just WPA2
Enter the Wireless Password you want
Verify the Wireless Password (enter it again)
After it is created you will see it on the Airport Utility window with the name you created for it and to the left, will be a Dot (circle that will be yellow).
Next you then want to unplug the power to the Airport Extreme, and then take the end of the Ethernet cable you unplugged from the iMac or Lap top MacBook Pro and connect it to the back of the Modem.
Next unplug the power cord from the modem and wait about 5 minutes, then plug the power back into the Arris Modem and wait until all lights come back on the modem wait
about 5 minutes, then plug the power cord back to the Airport Extreme and you will see it the light blinking yellow. Wait about 5 to 10 minutes, during this time Restart you IMAC or MacBook Pro, and once it is back up click on the Airport Utility and you should see on the Airport Utility screen.
For INTERNET to the left the light should be green and you should see the Airport Extreme also appear and the light to the left on the screen should also be green. If they are, you then should be able to click on the Wireless Symbol on top of bar of the screen and click to select the Wireless Network Name you created.
If you Do Not See the light (Icon) next to INTERNET turn Green, or if you see the Internet Light Green, but the Light (Icon) next to the Airport Extreme is yellow, unplug the power again to the modem and unplug the power again to the Airport extreme and wait about 15 minutes or up to 30 minutes. Then plug the power cord back to the modem wait till all the lights light up then, plug the power cord back into the Airport Extreme and Restart your iMAC or MacBook Pro.
The Airport Extreme light should change from yellow to green. Open up the Airport Utility to see what the indicators are showing they should both be green. Again select Wireless network you created under the Wireless Icon on the top right of the screen. Open Safari and see if you are able to Route to a web page or the apple site should appear.

I just got a Charter Modem. Model TM822. While I was moving, my Airport Extreme was still at my old place.
I have a Linksys WRT320N I used for the initial Charter setup.
I can get my Airport to work here, but the Internet light on the Modem flashes Yellow.
Hasn't caused any issues so far but one thing I did notice.
On the Linksys there were 3 DNS servers listed.
The Airport Extreme only lists 2 and i don't see where I could add another, only change whats already there.
I tried everything above, but light on modem still flashes yellow.
I have the technicians cell phone. Told me "that shouldn't be" and gave the same advice listed above.
I'll break down and call Charter one day, see if it's on their end. NSA tracking may need a reset LMAO.

How can I save the first dept. for an employee in a transport table?

Hi All,
I have created a table to store the transports to an employee from department to another department.
the first department number to every employee is stored at the parent table called employees.
when I insert a new record to the transports table (which is the child for the parent employees) for an employee and the manager agrees for this transport the original value of department number in employees table will be changed to the new one. I done this process through a db trigger on the transport table.
Now the problem is that the original value of the first department number will be lost cause of the db trigger that changes this value after manager agreement!
I looked to solve the problem by adding a new column in employees table to save the first dept. no. for each employee only if Count of records = 1 for that employee like this:
-- Before Update DB Trigger on Transports Table:
DECLARE
pragma autonomous_transaction;
N NUMBER;
BEGIN
SELECT count(EMP_SID) -- emp-sid is the FK referenced from employeess.emp_sid
INTO N
FROM TRANSPORT_TRANS
where emp_sid=:NEW.EMP_SID
GROUP BY EMP_SID;
     IF :NEW.AGREE_FLG = 1 AND N = 1 THEN -- If the manager agrees and this record is the first one for that employee
     UPDATE EMPLOYEESS E
     SET E.FST_AD=E.ADMINISTRATION_SID, -- E.ADMINISTRATION_SID has the oroginal value for admin no. and FST_AD is the new column to save the first value
            E.FST_HE=E.HEADQUARTERS_SID,
            E.ADMINISTRATION_SID = :OLD.ADMIN_SID, -- changing the value with then new one added on the table
            E.HEADQUARTERS_SID = :OLD.HEAD_SID
           WHERE E.EMP_SID = :OLD.EMP_SID;
     ELSIF :NEW.AGREE_FLG = 1 AND N != 1 THEN -- if the manager agrees but the record is not the first record for that employee
     UPDATE EMPLOYEESS E
        SET   E.ADMINISTRATION_SID = :OLD.ADMIN_SID, -- only change the original values
                 E.HEADQUARTERS_SID = :OLD.HEAD_SID
                 WHERE E.EMP_SID = :OLD.EMP_SID;
     END IF;
END;But the form gives me this error if I deleted (pragma autonomous_transaction;) st. :
ORA-04091: table transports is mutating, trigger/function may not see it
But when I keep it, the form gives me this error:
ORA-06519: active autonomous transaction detected and rolled back
Edited by: Dev. Musbah on Aug 18, 2009 2:09 AM

Dev. Musbah,
First make sure that the insert statement executes. And check whether other error messages are getting. Currently you are checking only NO_DATA_FOUND. so change the exception part with
EXCEPTION
     WHEN NO_DATA_FOUND THEN NULL;
     WHEN OTHERS THEN MESSAGE('Some Error Occured');Regards,
Manu.
If this answer is helpful or correct, please mark it. Thanks.

Getting the first row for each group

Hi Everyone,
I have a query which returns a number of rows, all of which are valid. What I need to do is to get the first row for each group and work with those records.
For example ...
client flight startairport destairport stops
A fl123 LGW BKK 2
A fl124 LHR BKK 5
B fl432 LGW XYZ 7
B fl432 MAN ABC 8
.... etc.
I would need to return one row for Client A and one row for Client B (etc.) but find that I can't use the MIN function because it would return the MIN value for each column (i.e. mix up the rows). I also can use the rownum=1 because this would only return one row rather than one row per group (i.e. per client).
I have been investigating and most postings seem to say that it needs a second query to look up the first row for each grouping. This is a solution which would not really be practical because my query is already quite complex and incorporating duplicate subqueries would just make the whole thing much to cumbersome.
So what I really new is a "MIN by group" or a "TOP by group" or a "ROWNUM=1 by group" function.
Can anyone help me with this? I'm sure that there must be a command to handle this.
Regards and any thanks,
Alan Searle
Cologne, Germany

Something like this:
select *
from (
   select table1.*
   row_number() over (partition by col1, col2 order by col3, col4) rn
   from table1
where rn = 1In the "partition by" clause you place what you normally would "group by".
In the "order by" clause you define which will have row_number = 1.
Edit:
PS. The [url http://download.oracle.com/docs/cd/E11882_01/server.112/e17118/functions004.htm#i81407]docs have more examples on using analytical functions ;-)
Edited by: Kim Berg Hansen on Sep 16, 2011 10:46 AM

Installing applications twice on the same computer for different OS

Hi. I currently have the latest version of Tiger installed on a G5 PowerMac. I'm planning to replace my boot drive w/ a larger drive and partition it, using one partition for Tiger and the 2nd partition for Leopard (10.5.8). As I understand it, applications must be installed on the same partition w/ the OS so I assume I will have to reinstall any applications that I am now using w/ Tiger onto the Leopard partition as well (if I would also like to be able to use them w/ Leopard). This will result in applications being installed twice on the same computer, one installation on the Tiger partition and a 2nd installation on the Leopard partition. Has anyone done this successfully w/ Adobe CS3 applications? I'm not sure if this question might be better suited for an Adobe forum but I was hoping someone here might be able to provide some helpful feedback. I would also like to know if there are any other issues that I should be aware of concerning installing the same application on two different partitions. Thanks for your consideration. (I would also like to be able to do this w/ FCP6.)
Jack

Hi Jack,
First finish 10.4 Install, then clone the 10.4.11 patition to the one you want to use for 10.5...
Get carbon copy cloner to make an exact copy of your old HD to the New one...
http://www.bombich.com/software/ccc.html
Or SuperDuper...
http://www.shirt-pocket.com/SuperDuper/
Or the most expensive one & my favorite, Tri-Backup...
http://www.tri-edre.com/english/tribackup.html
Then Install 10.5 on that partition... it went fine for me.

After shutdown I have to log in twice. The first time it starts to load, then goes black, then gives me login page again. Do you think I have a virus? Or is this Yosemite bug?

Just updated to Yosemite on my MBP. After shutdown now when I login, it starts the process (the bar starts to move), then the screen goes black, then it asks me to login again and this time it is a successful startup. Is this a Yosemite bug or do I have a virus? I also have some funny tiling on the screen at youtube and some other websites. Another bug?

Reinstalling OS X Without Erasing the Drive
Boot to the Recovery HD: Restart the computer and after the chime press and hold down the COMMAND and R keys until the menu screen appears. Alternatively, restart the computer and after the chime press and hold down the OPTION key until the boot manager screen appears. Select the Recovery HD and click on the downward pointing arrow button.
Repair the Hard Drive and Permissions: Upon startup select Disk Utility from the main menu. Repair the Hard Drive and Permissions as follows.
When the recovery menu appears select Disk Utility. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the main menu.
Reinstall OS X: Select Reinstall OS X and click on the Continue button.
Note: You will need an active Internet connection. I suggest using Ethernet if possible because it is three times faster than wireless.
Also see:
Reinstall OS X Without Erasing the Drive
OS X Yosemite- Reinstall OS X
OS X Mavericks- Reinstall OS X
OS X Mountain Lion- Reinstall OS X
OS X Lion- Reinstall Mac OS X
Note: You will need an active Internet connection. I suggest using Ethernet
if possible because it is three times faster than wireless.

Get only the first row for duplicate data

Hello,
I have the following situation...
I have a table called employees with column (re, name, function) where "re" is the primary key.
I have to import data inside this table using an xml file, the problem is that some employees can be repeated inside this xml, that means, I'll have repeated "re"'s, and this columns is primary key of my table.
To workaround, I've created a table called employees_tmp that has the same structed as employees, but without the constraint of primary key, on this way I can import the xml data inside the table employees_tmp.
What I need now is copy the data from employees_tmp to employess, but for the cases where "re" is repeated, I just want to copy the first row found.
Just an example:
EMPLOYEES_TMP
RE NAME FUNCTION
0987 GABRIEL ANALYST
0987 GABRIEL MANAGER
0978 RANIERI ANALYST
0875 RICHARD VICE-PRESIDENT
I want to copy the data to make employees looks like
EMPLOYEES
RE NAME FUNCTION
0987 GABRIEL ANALYST
0978 RANIERI ANALYST
0875 RICHARD VICE-PRESIDENT
How could I do this?
I really appreciate any help.
Thanks

Try,
SELECT re, NAME, FUNCTION
FROM (SELECT re,
               NAME,
               FUNCTION,
               ROW_NUMBER () OVER (PARTITION BY re ORDER BY NAME) rn
          FROM employees_tmp)
WHERE rn = 1G.

How to select the first row for each pair of values ?

Hi guys, am hoping someone can help me here.
If I have 4 tables - Building, Dept, Emp, Text
B D E T
A 1 Z blah1
A 1 X blah2
A 1 W blah3
A 2 V blah4
A 2 G blah5
A 2 H blah6
B 1 K blah7
B 1 L blah8
B 2 E blah9
B 2 F blah0
I need a query that will bring back the first bit of text for each pair of building and dept records.
So the results I would get would be
A 1 blah1
A 2 blah4
B 1 blah7
B 2 blah9
blah2 wouldnt be returned, because we have already had a record from the Building A, dept 1 pairing.
Likewise we wouldnt get blah5 because we have already had a record from the Building A, dept 2 pairing.
Can this be done in 1 query??
Thanks all.
Message was edited by:
Scott Hillier

here you go
SQL> drop table t;
Table dropped.
SQL> create table t(B char(1), D integer, E char(1), T varchar2(5));
Table created.
SQL> insert into t values('A', 1, 'Z', 'blah1');
1 row created.
SQL> insert into t values('A', 1, 'X', 'blah2');
1 row created.
SQL> insert into t values('A', 1, 'W', 'blah3');
1 row created.
SQL> insert into t values('A', 2, 'V', 'blah4');
1 row created.
SQL> insert into t values('A', 2, 'G', 'blah5');
1 row created.
SQL> insert into t values('A', 2, 'H', 'blah6');
1 row created.
SQL> insert into t values('B', 1, 'K', 'blah7');
1 row created.
SQL> insert into t values('B', 1, 'L', 'blah8');
1 row created.
SQL> insert into t values('B', 2, 'E', 'blah9');
1 row created.
SQL> insert into t values('B', 2, 'F', 'blah0');
1 row created.
SQL> select b,d,t
2    from (
3 select row_number() over(partition by b, d order by b,d) rno,b,d,t
4    from t)
5   where rno = 1;
B          D T
A          1 blah1
A          2 blah4
B          1 blah7
B          2 blah9karthick
http://karthickarp.blogspot.com/

Essbase 9.3.1 fails login the first time for both LDAP and Native users

Hi,
Whenever I try to login into Essbase server using AAS or Maxl, it fails for the first time but when I try the second time it works.
Essbase Logs at the time of the error shows:
Local ESSBASE0 Info (1051001) Received client request: Get Log File (from user hadmin )
Local ESSBASE0 Info (1051001) Received client request: Get Server Locale Description (from user hadmin )
Local ESSBASE0 Info (1051164) Received login request from xxx.xxx.xxx.x
Local ESSBASE0 Error (1051293) Login fails due to invalid login credentials
Local ESSBASE0 Warning (1051003) Error 1051293 ~processing request Login - disconnecting
SharedServices9\SystemErr.log
SystemErr R com.hyperion.interop.AuthenticationException: Could not authenticate user 'CSSToken'. Please ensure the username and password is correct.
SystemErr R at com.hyperion.interop.webservices.Security.slideAuthenticate(Unknown Source)
SystemErr R Caused by: java.lang.Exception: Interop Security: Unauthorized
SystemErr R at com.hyperion.interop.webservices.Security.authenticate(Unknown Source)
SystemErr R 1282785593 [WebContainer : 0] WARN security.SecurityFacade - Error Executing cssAuthenticate()
Error Code: -1
com.hyperion.css.CSSTokenNotAcceptedException: Token is invalid. Error Code: 11
And we are using SSL? Help please... Thanks.

I know this wont help but we had the same issue in 9.3.1 and decide to reinstall without SSL as we could not get to the bottom of it.
I suspect there s something wrong with the SSL config but not sure what it is...
Seb

Only the first page for a particular site prints. All other sites are fine.

I'm running Firefox 10.0.2 on Windows 7 SP1 and when I try to print the web page of the affected URL ( http://windows.microsoft.com/en-US/windows-vista/Connect-to-another-computer-using-Remote-Desktop-Connection ), only the first page is printed. It prints fine in IE 9. I tried printing in safe mode and it still only prints the first page. I only tried printing it once, after that I used print preview alone. I used print preview on a dozen other sites and it works fine. By the way, on the web page I'm trying to print you must "Show All" at the bottom to expand all of the text. It's just this one web page. Can someone else with a similar setup try print preview on this page for me? I just want to know. I printed it using IE. Interestingly, if you scale the print preview down enough, all of the text shows up. Thanks...

Well, I've made a little progress. I saved the web page source locally and then added the following HTML snippet to the <head> section:
<style type="text/css">
div
page-break-before:always;
</style>
When I display this, the "Show all" does not work, but the page text is still long enough to do "Print Preview" and expect more than one page. The result is a blank first page (expected) and then ALL of the page text is printed on the next two pages.
But I think you are correct "the-edmeister" in saying that Firefox may have a problem when the DIV tag spans more than one page. The reason is that the third page only contains the footer, so I can't say for sure if the whole DIV block was printed. But at least the footer did show up this time.
If I can get the "Show all" block to expand then maybe that question will be answered. Any thoughts?

How long is the first charge for the first time?

Hello everyone! I've just got the newest iPod Touch and I was wondering for how long does it need to be charged for the first time.
Thank you for your help and best wishes for these holidays.

Just charge it until it is fully charged. Not reason or requirement to charge more.

The first time for MVVM and I got a problem. I need help.

App.cs
#if DEBUG
if (System.Diagnostics.Debugger.IsAttached)
this.DebugSettings.EnableFrameRateCounter = true;
#endif
Frame rootFrame = Window.Current.Content as Frame;
// Do not repeat app initialization when the Window already has content,
// just ensure that the window is active
if (rootFrame == null)
// Create a Frame to act as the navigation context and navigate to the first page
rootFrame = new Frame();
var viewModel = new MainWindowModel();
MainPage main = new MainPage();
main.DataContext = viewModel;
// TODO: change this value to a cache size that is appropriate for your application
rootFrame.CacheSize = 1;
if (e.PreviousExecutionState == ApplicationExecutionState.Terminated)
// TODO: Load state from previously suspended application
// Place the frame in the current Window
Window.Current.Content = rootFrame;
DataAccess.cs
readonly List<Menu> _menu;
public MenuRespository()
if(_menu==null)
_menu = new List<Menu>();
_menu.Add(Menu.CreateMenu("/Photos/Gas-50.png", "t"));
_menu.Add(Menu.CreateMenu("/Photos/Gas-50.png", "t"));
_menu.Add(Menu.CreateMenu("/Photos/Gas-50.png", "t"));
_menu.Add(Menu.CreateMenu("/Photos/Gas-50.png", "t"));
_menu.Add(Menu.CreateMenu("/Photos/Gas-50.png", "t"));
_menu.Add(Menu.CreateMenu("/Photos/Gas-50.png", "t"));
_menu.Add(Menu.CreateMenu("/Photos/Gas-50.png", "t"));
public List<Menu> GetMenu()
return new List<Menu>(_menu);
Menu.cs
public class Menu
public static Menu CreateMenu(string iconthumb, string text)
return new Menu { IconThumb = iconthumb, Text = text };
public string IconThumb { get; set; }
public string Text { get; set; }
MainWindowsModel
public class MainWindowModel :ViewModelBase
readonly MenuRespository _menuRepository;
ObservableCollection<ViewModelBase> _viewModels;
public MainWindowModel()
_menuRepository = new MenuRespository();
//create an instance of our viewmodel add it to our collection
MenuListViewModel viewModel = new MenuListViewModel(_menuRepository);
this.ViewModels.Add(viewModel);
public ObservableCollection<ViewModelBase> ViewModels
get
if(_viewModels==null)
_viewModels = new ObservableCollection<ViewModelBase>();
return _viewModels;
ViewBase
public abstract class ViewModelBase :INotifyPropertyChanged, IDisposable
protected ViewModelBase()
public event PropertyChangedEventHandler PropertyChanged;
protected virtual void OnPropertyChanged(string propertyName)
PropertyChangedEventHandler hander = this.PropertyChanged;
if(hander!=null)
var e = new PropertyChangedEventArgs(propertyName);
hander(this, e);
public void Dispose()
this.Dispose();
protected virtual void OnDispose()
class MenuListViewModel :ViewModelBase
readonly MenuRespository _menuRepository;
public ObservableCollection<Model.Menu> AllMenu
get;
private set;
public MenuListViewModel(MenuRespository menuRepository)
if(menuRepository==null)
throw new ArgumentException("menuRepository");
_menuRepository = menuRepository;
this.AllMenu = new ObservableCollection<Model.Menu>(_menuRepository.GetMenu());
protected override void OnDispose()
//base.OnDispose();
this.AllMenu.Clear();
MenuListBox.xaml into View(show off "
<UserControl
x:Class="MixNokia.View.MenuListBox"
xmlns="http://schemas.microsoft.com/winfx/2006/xaml/presentation"
xmlns:x="http://schemas.microsoft.com/winfx/2006/xaml"
xmlns:local="using:MixNokia.View"
xmlns:d="http://schemas.microsoft.com/expression/blend/2008"
xmlns:mc="http://schemas.openxmlformats.org/markup-compatibility/2006"
mc:Ignorable="d">
<StackPanel>
<ListBox ItemsSource="{Binding AllMenu}">
<ListBox.ItemTemplate>
<DataTemplate>
<StackPanel Orientation="Horizontal">
<Image Source="{Binding IconThumb}" Width="40" Height="40" VerticalAlignment="Center" HorizontalAlignment="Left"></Image>
<TextBlock Text="{Binding Text}" FontSize="15" Foreground="#CCCCCC" VerticalAlignment="Center" HorizontalAlignment="Center"></TextBlock>
</StackPanel>
</DataTemplate>
</ListBox.ItemTemplate>
</ListBox>
</StackPanel>
</UserControl>
The final
<Page
x:Class="MixNokia.MainPage"
xmlns="http://schemas.microsoft.com/winfx/2006/xaml/presentation"
xmlns:x="http://schemas.microsoft.com/winfx/2006/xaml"
xmlns:local="using:MixNokia"
xmlns:d="http://schemas.microsoft.com/expression/blend/2008"
xmlns:mc="http://schemas.openxmlformats.org/markup-compatibility/2006"
xmlns:vm="using:MixNokia.ViewModel"
xmlns:v="using:MixNokia.View"
mc:Ignorable="d">
<Page.DataContext>
<vm:MainWindowModel />
</Page.DataContext>
Mainpages.
<ListBox x:Name="lstMainMenu" SelectionChanged="lstMainMenu_SelectionChanged" Background="Transparent" ItemsSource="{Binding ViewModels}">
I'm developing on universal..
It was showing "mixnokia.viewmodel.menulistviewmodel "

Greg - please tell us exactly what is wrong when you make a post.
Matt Small - Microsoft Escalation Engineer - Forum Moderator
If my reply answers your question, please mark this post as answered.
NOTE: If I ask for code, please provide something that I can drop directly into a project and run (including XAML), or an actual application project. I'm trying to help a lot of people, so I don't have time to figure out weird snippets with undefined
objects and unknown namespaces.

HT4061 I had read that Apple will replace a cracked screen on an iPad the first time for free. Does anyone know if this is true?

I have read that Apple will replace a cracked screen on an iPad the first time it is damaged for free. Does anyone know if this is true?

apple's official policy is: cracked screens = accidental damage
With iPad 1 and 2, accidental damage is not covered by any apple care and a replacement iPad starts at $249 and goes up depending on the model.
iPad3's were eligible for Apple Care + which offers two instances of accidental damage repair for $49 each time
The 'apple store replaced my cracked ipad for free' is largely an urban legend. It's possibly happened, but those that have been on the receiving end were people that happened to get a store manager that defied Apple's official policy. Not to say it hasn't potentially happened, but it's an exception not the rule. And if you happen to be lucky enough to experience it, that's just what it is, luck. Not something to be counted on or expected.

Skype shows busy after the first call for any inco...

Just for the sake of community I am posting this. I have a new Lenovo Yoga 3 which I love. Its running windows 8.1. I have installed MS Office, BitDefender, Google Docs, Chrome, Opera, Dropbox and Skype.
Prior to the new version of Skype 7 I was on version 6.21.104 and it worked fine for a long time. When I switched to the new Skype 7 after buying my Yoga 3 it broke. Now I rely on Skype heavilly for my work. With version 7 after I receive a call, I could no longer receive any further calls I just show a busy banner and hear the error tone when people try. I deinstalled Skype with special tools like revouninstaller. I cleaned the registry of all Skype entries. Removed all files. Did it several times. On this machine Skype 7 has a serious bug.
MY ONLY Solution was to go to an older version of skype .. skype 6.021.104. Works just fine now.
Microsoft -- get your act together. You are famous for putting out buggy software. Skype in particular has been very bad over time -- so pull it together or we will switch to something else and others will follow. By the way I am a software developer

Ok, I've edited the VI you posted to reproduce my error (this time with 8.0).
I added a "master stop" and "start log" button. To demonstrate my problem:
1. Run the VI
2. Click "START LOGGING" - c:\test.txt is created
3. Click "STOP" - c:\test.txt is closed
4. Delete the file c:\test.txt with Windows shell or explorer
5. Click "START LGGING" - a new c:\test.txt file should be created but instead an error is raised in the Write LabVIEW Measurement File function.
Any ideas?
Thanks,
Dave
Attachments:
Write LV Meas File 2.vi ‏96 KB

How to change the first listing for company name in contacts

How do i get the company name to show in the list instead of the persons name.
I can do this with my pc, but my dad only sync's with the cloud & I can't find how to sort showing the company name, ie APPLE instead of John Doe & can't see that he works for Apple unless you select the contact.

That isn't supported on an iPhone. There may be apps that would do this, but not the built-in contacts app. You could, of course, create contact groups on icloud.com for major companies and add the appropriate contacts to these groups, and these groups would sync to your device.

WITEM GOIN TWICE TO THE FIRST APPROVER for SC APPROVAL

Similar Messages

Maybe you are looking for