WL on Soalris and Apache on Linux

Hi
I'm new to WL and I'm in installation phase. Is it possible to install WL on
Solaris and Apache on Linux (intel cpu)?
If possible is it logical to do it like that (performance and security is
very important)?
Regards
Lutfi
[email protected]

It is definitely possible, I have the exact same setup running right now.
From a security and performance perspective, however, you'd be better off
using Solaris on both. The only reason I am using Linux in front is cost.
Lutfi Yunusoglu <[email protected]> wrote in message
news:[email protected]..
Hi
I'm new to WL and I'm in installation phase. Is it possible to install WLon
Solaris and Apache on Linux (intel cpu)?
If possible is it logical to do it like that (performance and security is
very important)?
Regards
Lutfi
[email protected]

Similar Messages

OAS and Linux and Apache

I have successfully installed OAS 4.0.8.1 on Linux RedHat 6.1. The default (oracle) http listner runs fine, after setting it to port 81. I did this because the default http server for Linux (Apache 1.3.9-4) is on 80. I would like to use Apache as my http listner, and have found some documentation on how to do this at http://www.olab.com/doc/books/admin/thirdp.htm, but am a little confused with the instructions. It states that Apache must be compiled with mod_so support. I have verified that this is so with the "httpd -l" command. Before that, it mentions that...
"libapadp.so must be linked into the Apache HTTP Server." Can anyone tell me how this is done, and with which version of Apache should be used? 1.3.6 seems to be a popular one and is mentioned in the Oracle Application Server Installation Guide for Release 4.0.8.1 in Certified Software.
I have tried to move libapadp.so and ndwfapd.so into the /modules subdirectory my Apache install (once again 1.3.9-4) and adding "LoadModule ows_module ndwfapd.so" in my httpd.conf file, but when the server tries to start, I get the error message...
"Cannot load /etc/httpd/modules/ndwfapd.so into server:libapadp.so: cannot open shared object file:No such file or directory"
Has anyone run into this problem? I imagine many people have done this. As I am new to Linux and OAS and Apache, maybe I'm missing something fundamental that I haven't learned yet, but hey, isn't this what learning is all about?
If anyone can help me with this hurdle, I would greatly appreciate it.
Thanks in advance,
Kirby

Hi Guys,
I am pulling my hair out with this one too.
I tried to link the library "libapadp.so" to
apache using the Makefile in the source directory by adding the path and libapadp.so to the EXTRALIBS variable. It works in the
sense that it tried to link the lib but fails because there are a bunch of unresolved dependencies. As somebody else stated, Oracles documentation sucks. I ask for support and got sent here, I guess that they don't know how to make it work either.
Will let you know if I have any success.
Brett.
[email protected]
<BLOCKQUOTE><font size="1" face="Verdana, Arial">quote:</font><HR>Originally posted by Jason Gerry ([email protected]):
I've been working on this problem as well. I haven't got it to work YET, but I'm trying.
Your error message is relating to Apache not being able to find the shared module. You can fix this by telling it explicitly where to find it since it doesn't seem to be in the PATH.
LoadModule ows_module /opt/app/oracle/product/8.0.5/ows/4.0/lib/ndwfapd.so
Your directory structure may be different. In any case, this SHOULD work, my Apache listeners start up, but they don't actually respond to requests and they freeze the machine. Oh well.
Still working on it!
jason
<HR></BLOCKQUOTE>
null

Using UltraSearch and Apache to implement Desktop Search on Linux/Windows

Hi all:
I made this howto for implementing Desktop Search on Linux/Windows using UltraSearch and Apache.
Here the link:
http://www1.exa.unicen.edu.ar/~mochoa/Miscellaneous/My_Desktop_Search-5.pdf
Hope this hack, Marcelo.

>
I have used eclipse to create an executable jar. This is run on the console with commands like
#java -jar myJarFile.jar
Am using linux(OpenSUSE)
How can I create an executable file in search a way that the use just clicks on the icon and the system launches?>There are at least two basic ways you can head.
1) Add a manifest file to the Jar that specifies the main class. The end user can 'double click' it to launch the app.
2) Deploy the Jar using webstart, which can install desktop and menu item shortcuts for a program (plus adding splash screens, automatic update..) while installing it.

WLS 5.1 sp4 on Redhat 6.2 and Apache 1.3.12

The file mod_wl.so for linux should be available from sp3 onwards but I
installed
WLS 5.1 and then sp4 - it does not contain the Apache-Weblogic bridge share
library for linux.
Any pointers... (I looked in lib/linux/ directory)
Should I install each of the service packs????
Hemanth

I was just able to locate it in service pack No. 4. Remember, there are
different versions of the plug-ins for Apache on Solaris vs. Apache on
Linux.
Thanks,
Michael
Michael Girdley
Product Manager, WebLogic Server & Express
BEA Systems Inc
"a" <[email protected]> wrote in message news:[email protected]..
The file mod_wl.so for linux should be available from sp3 onwards but I
installed
WLS 5.1 and then sp4 - it does not contain the Apache-Weblogic bridgeshare
library for linux.
Any pointers... (I looked in lib/linux/ directory)
Should I install each of the service packs????
Hemanth

Configuring tomcat and apache on the same system

i need to configure tomcat and apache on the same system.
first i have configured apache and it is working well.
Next is have configured tomcat and it is working well.
i need to interlink tomcat and apache. so i downloaded jk connector and i have configured it.
i gave an entry in the httpd.conf as
Include /tomcat/conf/auto/mod_jk.conf
i have copied the file mod_jk.so to /usr/local/apache/libexec/
went i start apache after the entry is given it gives the error like this
cannot load /usr/local/apache/libexec/mod_jk.so into server: ld_so.1. /usr/local/apache/bin/httpd: fatal : libgcc_s.so.1 : openfailed : no such file or directory in linux
please help to configure this.
i have done every thing as it is in apache.org documentation. please give the complete configuration. some say that tomcat is not compiled according to apache1.3. but i configure jk connector as --with-apxs=/usr/local/apache/bin/apxs
send me the reply
thankqs in advance

Hi,
I'm working in a linux machine and choose to use also two different users. Of course I'm using two different ORACLE_HOME directories.I think that the best approach.Just a question ,are you keeping the "GROUP" same or different?
Anand

Upgrading to PHP 5 on Tiger and Apache 1.3

I need a little help with configuring php on my local server. I love XHTML/CSS and a bit of php, WordPress, and Rails - but I'm terrible at this server stuff. I'm petrified of screwing my configuration.
I'm running everything from the default OS X Apache server (I'm on Tiger OS X 10.4.10). I prefer using the internal server to all-in-one apps like MAMP and Locomotive. I have phpMyAdmin v2.10.2, MySQL v5.0.24a, and I think I'm running php 4.4.7 (typing php -v whilst in my document root in terminal returns version 4.4.7).
I now want to use the latest version of php. However, I can't remember if I upgraded php when I was installing MySQL etc. If not, is it possible that I installed the latest version, and I'm just not using at the moment (which could be why terminal is saying it's version 4.4.7)? Is there anyway to check for dormant versions of php or to switch over to running a different version?
If I don't have it, I need to install it. Is there an easy way of doing this via an installer? Is there anything I need to watch-out for whilst I'm attempting this feat?
Also, does Leopard bring many advancements on the server front, i.e. Apache 2, php 5, MySQL etc, which might save me some hassle if I just go through the inevitable OS upgrade sooner rather than later?
Any help is much appreciated.

I now want to use the latest version of php. However, I can't remember if I
upgraded php when I was installing MySQL etc. If not, is it possible that I
installed the latest version, and I'm just not using at the moment (which could
be why terminal is saying it's version 4.4.7)? Is there anyway to check for
dormant versions of php or to switch over to running a different version?
Well you could try this in terminal:
<pre style="font-family: monospaced;">locate php</pre>
It should show you nearly everything associated with php. As far as what the php version command lists this only picks up the CLI version of php not necessarily whats running on the web server. throw a php file in your webroot with the following code in it to see what the server is using:
<pre style="font-family: monospaced;"><?php phpinfo(); ?></pre>
That will give you the lowdown on what Apache is configured with. this is goign to depend on what mod_php is being used.
Generally i wouldnt upgrade anything that lives in the system as you never know if it might get overwritten or updated when a system update comes down from apple. A better practice is to install the version you want to use to /usr/local/<dirname> so that the installations are isolated and manageable.
If I don't have it, I need to install it. Is there an easy way of doing this via
an installer? Is there anything I need to watch-out for whilst I'm attempting
this feat?
I generally use the php packages from www.entropy.ch just so i dont have to bother with compiling. My versions of Ruby, Apache 2.0.x and Apache 2.2.x i compiled myself, along with an upgraded version of Python and alot of other libraries.
Then you can jsut make some changes to configuration files to use the versions you want. However if you use the entropy.ch packages of php as i suggested the installer takes care of the configuration changes for you. Jsut make sure you grab the one for the proper version of apache youre going to be using it with.
Additionally you could always get Mac/DarwinPorts - whatever its called now... this is a package manager like apt-get or yum under linux. It fetaches the package for you from a repository, and installs it. I dont use these because they use a different dir structure than standard Darwin - ie. the create the /opt folder and install under this. I dont really like that so i dont use them - but that isnt going to cause you any problems, its jsut a preference thing.
Also, does Leopard bring many advancements on the server front, i.e. Apache 2,
php 5, MySQL etc, which might save me some hassle if I just go through the
inevitable OS upgrade sooner rather than later?
I know it comes with apache 2. I think it may also come with php 5.1.6 (5.2.x is avialable though).. not sure about MySQL at all...

Dreamweaver created website on Apache/Tao Linux host

I was creating a simple 5 page website based on a DW
template, and once I FTP'd the home page ("Index.html") to the web
host, I recieved an Apache setup screen - as if the file I placed
wasn't read or understood. I renamed the original Index.html back
and the site came up as expected. The original file is a very basic
html file - Is there any known issues with Dreamweaver created
files on host sites using Apache & Tao Linux, and if so is
there a method of preparing the web pages for use on such a site?
Thanks,
Tom

> rename your new "homepage" to index.html
to add- to do this in dreamweaver so it maintains/fixes links
when you
change the case of a file or foldername-
use the Files panel.
right-click on Index.html and "rename" to fooindex.html
okay updating links.
rename fooindex.html to index.html
okay updating links.
now upload ALL changed files

Compile problem using TOMCAT 5.0 and Apache ANT

I got some sample from book.
i just follow the step, place it the class file. it work. it run. show all the detail.
but when i wan to compile it from java file, error came out
type Exception report
message
description The server encountered an internal error () that prevented it from fulfilling this request.
exception
javax.servlet.ServletException: Error allocating a servlet instance
     org.apache.catalina.valves.ErrorReportValve.invoke(ErrorReportValve.java:118)
     org.apache.coyote.tomcat5.CoyoteAdapter.service(CoyoteAdapter.java:160)
     org.apache.coyote.http11.Http11Processor.process(Http11Processor.java:799)
     org.apache.coyote.http11.Http11Protocol$Http11ConnectionHandler.processConnection(Http11Protocol.java:705)
     org.apache.tomcat.util.net.TcpWorkerThread.runIt(PoolTcpEndpoint.java:577)
     org.apache.tomcat.util.threads.ThreadPool$ControlRunnable.run(ThreadPool.java:683)
     java.lang.Thread.run(Unknown Source)
root cause
java.lang.NoClassDefFoundError: com/jspbook/HelloWorld (wrong name: HelloWorld)
     java.lang.ClassLoader.defineClass1(Native Method)
     java.lang.ClassLoader.defineClass(Unknown Source)
     java.security.SecureClassLoader.defineClass(Unknown Source)
     org.apache.catalina.loader.WebappClassLoader.findClassInternal(WebappClassLoader.java:1634)
     org.apache.catalina.loader.WebappClassLoader.findClass(WebappClassLoader.java:860)
     org.apache.catalina.loader.WebappClassLoader.loadClass(WebappClassLoader.java:1307)
     org.apache.catalina.loader.WebappClassLoader.loadClass(WebappClassLoader.java:1189)
     org.apache.catalina.valves.ErrorReportValve.invoke(ErrorReportValve.java:118)
     org.apache.coyote.tomcat5.CoyoteAdapter.service(CoyoteAdapter.java:160)
     org.apache.coyote.http11.Http11Processor.process(Http11Processor.java:799)
     org.apache.coyote.http11.Http11Protocol$Http11ConnectionHandler.processConnection(Http11Protocol.java:705)
     org.apache.tomcat.util.net.TcpWorkerThread.runIt(PoolTcpEndpoint.java:577)
     org.apache.tomcat.util.threads.ThreadPool$ControlRunnable.run(ThreadPool.java:683)
     java.lang.Thread.run(Unknown Source)
note The full stack trace of the root cause is available in the Apache Tomcat/5.0.28 logs.in CMD:
set java_home = C:\Program Files\Java\jdk1.5.0_08
set classpath = C:\Program Files\Apache Software Foundation\Tomcat 5.0\common\lib
and Apache tomcat originally dont have servlet.jar but servlet-api.jar, i copy the servlet.jar from my friend
i compile it using Apache ANT
here the build.xml
<?xml version="1.0" ?>
<project name="jspbook" default="build" basedir=".">
<target name="build">
    <echo>Starting Build </echo>
    
    <antcall target="tomcatOff"/>
    
    <antcall target="compile"/>
    
    <antcall target="tomcatOn"/>
    <echo>Build Finished </echo>
</target>
<target name="tomcatOff">
    <echo>Turning Off Tomcat </echo>
    <exec executable="bash" os="Windows">
      <arg value="../../bin/shutdown.bat"/>
    </exec>
    <exec executable="bash" os="Linux">
      <arg value="../../bin/shutdown.sh"/>
    </exec>
</target>
<target name="tomcatOn">
    <echo>Starting Tomcat </echo>
    <exec executable="bash" os="Windows">
      <arg value="../../bin/startup.bat"/>
    </exec>
    <exec executable="bash" os="Linux">
      <arg value="../../bin/startup.sh"/>
    </exec>
</target>
<target name="compile">
    <javac
      srcdir="WEB-INF/classes"
      extdirs="WEB-INF/lib:../../common/lib"
      classpath="../../common/lib/servlet.jar"
      deprecation="yes"
      verbose="no">
      <include name="com/jspbook/**"/>
    </javac>
</target>
</project>compile success, but error in IE
paste the sample class file in,restart tomcat. i work again!
what is the problem!
even i compile the code inside the Jcreator, after set required libraries to servlet.jar or servlet-api.jar
compile it, success then run it in IE, same error!!!.
what should i do.
stil a beginer in servlet and jsp anyway.

and Apache tomcat originally dont have servlet.jar but servlet-api.jar, i copy the servlet.jar from my friend servlet.jar is an OLD version, you should only use servlet-api.jar!
wrong name: HelloWorldPerhaps there is a mistake in the class or packagename of the source file. Post the source here.

Run tomcat and apache together

how can i do that tomcat 4.0.6 and apache work at same time? , it is to say, how get Tomcat to runs application server while leaving your static pages on Apache under standard distribution for linux, and do not uses the port 8080, if not, that jsps runs in the domain, example:
i don't want this:
http://mydomain:8080/index.jsp
i want this:
http://mydomain/index.jsp
thanks in advanced.

i have encountered a similar problem, here's a useful URL:
http://raibledesigns.com/tomcat/index.html

Get Error on AM 7.0 do SSO on MS IIS 6.0 and Apache 2.0x

Hi...
I install AM 7.0/Sun Web 6.1 on Window (Java ES4). And I try to setup SSO between MS IIS 6.0 and Apache 2.0. I don't know how config in the AM by using amserver (web admin).
I already complete install Policy Agent for MS IIS and Apache 2.0 and both of web was protected.
I get the error msg on AM dubug log below :
IIS :
2006-06-26 22:56:18.376 Debug 3876:157ae90 AuthService: HTTP Status = 200 (OK)
2006-06-26 22:56:18.376 Debug 3876:157ae90 AuthService: Http::Response::readAndParse(): No content length in response.
2006-06-26 22:56:18.376 Error 3876:157ae90 AuthService: AuthService::processLoginStatus() Exception message=[Authentication Failed!!] errorCode='107' templateName=login_failed_template.jsp.
2006-06-26 22:56:18.376 Error 3876:157ae90 PolicyEngine: am_policy_evaluate: InternalException in AuthService::processLoginStatus() with error message:Exception message=[Authentication Failed!!] errorCode='107' templateName=login_failed_template.jsp and code:3
2006-06-26 22:56:18.376 Warning 3876:157ae90 PolicyAgent: am_web_is_access_allowed()(http://w2k3.sunth.com:81/index.html, GET) denying access: status = Access Manager authentication service failure
2006-06-26 22:56:18.376 Debug 3876:157ae90 PolicyAgent: am_web_is_access_allowed(): Successfully logged to remote server for GET action by user unknown user to resource http://w2k3.sunth.com:81/index.html.
2006-06-26 22:56:18.376 Info 3876:157ae90 PolicyAgent: am_web_is_access_allowed()(http://w2k3.sunth.com:81/index.html, GET) returning status: Access Manager authentication service failure.
2006-06-26 22:56:18.376 Debug 3876:157ae90 PolicyAgent: HttpExtensionProc(): status after am_web_is_access_allowed = Access Manager authentication service failure (3)
2006-06-26 22:56:18.376 Error 3876:157ae90 PolicyAgent: HttpExtensionProc(): status: Access Manager authentication service failure (3)
Thank you very much for your support
Wut

Hi ,
I was installed and configured policy agent successfully.while i am trying to access the application url i am getting following error.
I am using IIS6.0 and access manager 7.1.
Error 2824:15b9918 AuthService: AuthService::processLoginStatus() Exception message=[Application user ID is not valid.] errorCode='107' templateName=login_failed_template.jsp.
2009-03-10 00:03:05.828 Error 2824:15b9918 PolicyEngine: am_policy_evaluate: InternalException in AuthService::processLoginStatus() with error message:Exception message=[Application user ID is not valid.] errorCode='107' templateName=login_failed_template.jsp and code:3
2009-03-10 00:03:05.828 Warning 2824:15b9918 PolicyAgent: am_web_is_access_allowed()(http://fcs-ylwkuzfoz1q.ramesh.com:99/website.html, GET) denying access: status = Access Manager authentication service failure
2009-03-10 00:03:05.828 Debug 2824:15b9918 PolicyAgent: am_web_is_access_allowed(): Successfully logged to remote server for GET action by user unknown user to resource http://fcs-ylwkuzfoz1q.ramesh.com:99/website.html.
2009-03-10 00:03:05.828 Info 2824:15b9918 PolicyAgent: am_web_is_access_allowed()(http://fcs-ylwkuzfoz1q.ramesh.com:99/website.html, GET) returning status: Access Manager authentication service failure.
2009-03-10 00:03:05.828 Debug 2824:15b9918 PolicyAgent: HttpExtensionProc(): status after am_web_is_access_allowed = Access Manager authentication service failure (3)
2009-03-10 00:03:05.828 Error 2824:15b9918 PolicyAgent: HttpExtensionProc(): status: Access Manager authentication service failure (3)
2009-03-10 00:03:05.828 Debug 2824:15b9918 PolicyAgent: OnSendResponse(): HTTP Status code is 500
can any one please help me to resolve this.
Thanks
Ramesh Kumar GV

Remote desktop and apache

remote desktop and apache.
There are times I feel that someone is looking over my shoulder, and changing my settings and controlling me.
I would like to at least be able to communicate with them so I can ltarn. I also want to be able to monitor and have some say so as to what they are doing to my computer.
Thank you

Thanx for your reply.
I should have stated that this is my personal computer and if any one should be the administrator I would think it would be me.

About path and classpath in linux

How to set classpath and path in Linux.
thank you very much!

The class path can be set using either the -classpath option when calling an SDK tool (the preferred method) or by setting the CLASSPATH environment variable. The -classpath option is preferred because you can set it individually for each application without affecting other applications and without other applications modifying its value.
% sdkTool -classpath path1:path2...
-or-
% setenv CLASSPATH path1:path2...
where:
sdkTool
A command-line tool, such as java, javac, or javadoc. For a listing, see SDK Tools.
path1:path2
Paths to the .jar, .zip or .class files. Each path should end with a filename or directory depending on what you are setting the class path to:
For a .jar or .zip file that contains .class files, the path ends with the name of the .zip or .jar file.
For .class files in an unnamed package, the path ends with the directory that contains the .class files.
For .class files in a named package, the path ends with the directory that contains the "root" package (the first package in the full package name).
Multiple path entries are separated by colons.
The default class path is the current directory. Setting the CLASSPATH variable or using the -classpath command-line option overrides that default, so if you want to include the current directory in the search path, you must include "." in the new settings.
Classpath entries that are not either a directory or an archive (.zip or .jar file) are ignored.

Installing 11i apps on windows xp and Red Hat linux AS 3.0

Hi,
I am a newbie to Oracle E-business suite............i will be very helpful if anybody could help me with the full procedure on how to install Oracle apps on windows on Windows XP and Red Hat linux AS 3.0.........starting with configuring ip.....i would really appreciate if somebody helps me out...........well thanks in advance..waiting for a optmistic reply...
Thanks again,
Virendra

I have done installation on XP and 2000 servers are heres the steps... detailed ones. I also request those who install Oracle Apps 11i to first read the installtion pdf's which helps you understand clearly the prerequisites overall.
You cannot find the Pre installtion steps(such as Mks Toolkit and GNUMake config) in more clear terms from those documents.Which are explained here.
The Must PDF's to refer before installation
1)r1152ins.pdf
2)11iconcepts.pdf
According to the 11iconcepts PDF you can decide your business needs the N-Tier Architecture and Database Server and Application Tier Server File System in a very clear terms.
The installation process can be divided into
Pre Installtion,Installation and Post-Installation stages.
I would caution everyone to concentrate more on Pre Installation stage and which is more critical for a successfull installtion of Oracle Apps and to be free with later cropping up problems.
Further before moving into Installtion stages i have to Explain the Number of CD's and Installtion type's in Oracle App's.
In many places you may need to wait patiently even more than 10 minutes for screens(Dialog Boxes) to appear dont conclude prematurely some problem on system.
In oracle Apps 11.5.1 it consist of 12 CD's.
1) Start Here CD(RAPID Installation Wizard)
2)1-11 CD's
1-3 Application Top information
4th Oracle DB
5-6 IAS and other tools
7-11 Oracle Apps DB.
You have to decide whether you are going to do a Single Node Installation(No Post-Installation Task) or Multi Node Installation. Refer(r1152ins.pdf)
While installing for Multi Node you can see the Installation locations to be mentioned as
Appl_Top,Common_Top,Data_Top etc.Try to install Appl_top and common_Top in one drive and Data_Top in another Drive(Single Node) and in different nodes in Multi Node installation.
Installation Types
Production ==>Real time Env implementation's
Test ==>For test Env Purposes
Vision Demo==>R&D or learning Purposes.
Pre-Installation steps
======================
Space Requirement for types of installtions
Install VC++
How to Download and install MKS tool Kit
How to Download and Configure GNUMAKE
Env path setting
Create Applmgr user in Win2000
Space Requirement for types installtion:
Memory Requirement
1 GB of RAM(512 Fine for initial Installtion)
but planned for more user connections another 1 GB of Ram and according to the number of user's and Application needs you have to Increase the Memory.
HDD capacity
APP_Top(A)
COMMON_TOP(C)
DATA_TOP(D)
Test DB : 22 + 20 GB (60 GB recommended)
Prod DB : 22 + 20 GB (60 GB recommended)
Vision Demo DB: 22 + 35 GB (80 GB recommended).
Plus space for ur staging area.
This are the actuall space required for the Oracle Apps Alone plan for more space for future needs etc.
Softwares on System
Win2000 server with Patch1,Winzip and Acrobat Reader Latest version etc.
Install VC++:
Install a clean installtion of VC++ of Visual Studio Family 6.0
It should be first installed before installing MKS or GNUMAKE
NOTE: When Visual C++ is installed, let the installer register all environment variables. This will allow executables to be linked from the command line.
How to Download and install MKS tool Kit:
Note:Try to purchase the MKS tool kit from the below site.
or try to download the trial version valid for a months time.
http://www.mkssoftware.com/products/tk/ds_tkio.asp
Evaluation copy from
http://www.mkssoftware.com/eval/
Choose "MKS Toolkit for Interoperability " Download it in C:\
Again you have to click the downloaded kit to start the actual download of 38 MB of MKS tollkit Evaluation version.
You will be sent a Demo serial number to your mail id==>copy the same to a Notepad on your desktop.
Now start the installtion of the MKSToolkit on your system by clicking on the MKStoolkit downloaded.
It will prompt you for the Demo serial number which has to be provided.
The MKStoolkit will be successfully installed.
How to Download and Configure GNUMAKE:
1) HOW TO GET AND INSTALL GNUMAKE ON WINDOWS2000
This can be done by performing the following steps:
NOTE: Please, be aware that you must install Visual C++ BEFORE installing GNUMAKE, because its installation process involves linking executables.
1) Before downloading GNUMAKE, you will need to acquire some utilities which will be used for unpacking files. You can obtain the required utilities at the following
URL: ftp://ftp.gnu.org/gnu/windows/emacs/utilities/i386/
The directory contains the following files:
README
djtarnt.exe
gunzip-1.2.4-i386.exe
gzip-1.2.4-i386.exe
tar-1.11.2-i386.exe
tar-1.11.2a.exe
Only two of the files are required:
gunzip-1.2.4-i386.exe and tar-1.11.2a.exe
2) After downloading the above files, rename them as follows:
gunzip-1.2.4-i386.exe => gunzip.exe
tar-1.11.2a.exe => tar.exe
Place them into a directory that you can set in you PATH environment variable.
3) Point your browser to the following
URL: ftp://ftp.gnu.org/gnu/make
The files needed from this directory are:
make-3.77.tar.gz
make-3.78.1.tar.gz
make-3.79.1.tar.gz
make-3.79.tar.gz
Development requires to install version 3.77 or above. Downloading the latest version is perhaps best decision, but there are advantages to downloading the version required by development (3.77). (This document assumes that version 3.77 has been downloaded) (NOTE: AVOID USING SPACES IN
DIRECTORY AND FILE NAMES. GNUMAKE,VISUAL C++, ETC. DO NOT ALWAYS DEAL WELL WITH SPACES)
4) For instance, suppose you have downloaded file make-3.77.tar.gz on a directory called C:\GNUMAKE, unpack this file using gunzip.exe from a Command Prompt Window
Example: C:\GNUMAKE>gunzip make-3.77.tar.gz This last action, will expand file make-3.77.tar.gz and the extension .gz will be removed.
5) On the same Command Prompt Window, you should UnTAR the file, with the following
command: C:\GNUMAKE>tar -xvf make-3.77.tar This will create a new subdirectory called MAKE-3.77 under C:\GNUMAKE, the original directory.
6) In the new subdirectory, there is a batch file
called build_w32.bat; run the batch file to generate GNUMAKE.EXE
Try this from Command Prompt more than once if succesfully not built message appers till you get Generated successfully.
Note:If Possible run all the bat files in the MAKE-3.77 and also config.bat in the sub directory by double clicking it.
WARNING: There is a known issue with this last step, "GNU make fails to build regardless of chosing build_w32 or nmake"
See [NOTE:115937.1]
for work around. RELATED DOCUMENTS ----------------- For Microsoft Visual C++, MKS Toolkit and
GNUMAKE support, you should contact their respective vendors Microsoft Visual C++, MKS Toolkit
and GNUMAKE are registered trademarks.
http://support.microsoft.com/ http://msdn.microsoft.com/ http://www.mks.com/
http://www.gnu.org/ Note:104010.1: Release 11i on NT: Software Requirements
Note:115937.1: GNU Make won't make on windows NT
Important:All the downloaded files from GNU makes web sites shall be put in a single folder called gnumake under c:\ .Try to search for config.bat file inside this folders just click and
run it.
Env path setting:
Try to search make.exe generated in c:\program files\mkstoolkit\mksnt and copy and paste it
c:\gnumake\MAKE-3.77\windebug and c:\gnumake\MAKE-3.77\winRel also paste both this paths in the
My Computers==>Properties==>Advanced==>Environment variables==>Path setting's
After all this check as follows from CMD mode.
1)execute make at c:\>
2)execute gnumake at c:\>
In win2000 it may return error messages or Target wrong ignore it.If it is on Win NT then it will return proper status.
Create Applmgr user in Win2000:
Create a Applmgr user account in win2000 .
Installation:
=============
What here you require is the Patience .
Load the START HERE CD and run the C:\> cd \cdrom\rapidwiz
For Test and Prod it will ask for the location of Appl_Top,Common_Top and Data_Top location. Mention there path and ensure if more than one installtion say eg.Vision and Test or Prod to check the Path in all the tab pages its corresponding values and path's.
In Vision Demo many of the Options are not propmted from the user.
It will then do the system checking for Host Name and other details.All the checking should have been passed or if failed it will mark it in RED cross mark.Rectify the mistake and then onceagain proceed or else you will have problem after installation.
The Installation time takes around 5 to 6 Hrs of time.
For info on Post installation or on Multi Node follow the pdf's i have mentioned above.
The most tedious of all is succesfully crossing the Apps system checking it does for all
installed products it requires without any failure.
The GNUMAKE configuration or steps were nowhere given and it was all our trail and error exp.
This is possibly the most elaborate steps to install Apps on Win. post for further help. email me at [email protected] or [email protected]
Rajeev.

Installing Coldfusion 9 and Apache 2.2 on Windows Server 2008 R2 Standard

I'm having issues getting ColdFusion 9 working with Apache 2.2 on Windows Server 2008 R2 Standard.
The server is brand new and it's a fresh install of Apache and ColdFusion 9.
Having installed Apache, I tested the web server and it was working fine, so I proceeded to install ColdFusion 9. I attempted to restart the Apache server through the Apache Service monitor, only to get the error dialog box 'The requested operation has failed'.
On closer examination of the Windows error log, I saw the following error:
The Apache service named reported the following error: >>>
httpd.exe: Syntax error on line 488 of C:/Program Files (x86)/Apache Software Foundation/Apache2.2/conf/httpd.conf: Cannot load C:/ColdFusion9/runtime/lib/wsconfig/1/mod_jrun22.so into server: The Apache service named is not a valid Win32 application.
I updated the ColdFusion installation to 9.0.1 in case there was an issue with version 9.0 and Apache. Still no joy.
After a bit of research, I thought perhaps there was an issue with the mod_jrun22.so file (since when I commented out the reference to that file from the Apache config file, the Apache HTTP server started without any problem). I tried replacing the mod_jrun22.so with the 32 bit version (extracted from the wsconfig.jar file), but that made no difference either.
I have tried a number of things. I have run wsconfig and uninstalled all web server connectors and then re-created them.
I have to use Apache and IIS is not an option (I use rewrite rules extensively in an existing live installation and have many sites set up in a vhosts file), so please - no suggestions to use IIS instead.
The system requirements on http://www.adobe.com/sea/products/coldfusion/systemreqs/ state that Coldfusion 9 will work with Apache 2.2.17 and later on Windows 64 bit, so why am I having issues with a brand-new installation on a 'virgin' server?
Any help would be much appreciated. I have spent hours trawling the Web for solutions.

I missed an important detail in my opening post. My Coldfusion 9 version is 64 bit - not 32.
OK. Simple solution to this. I'll put it here for other peoples' reference.
To cut a long story short, after phoning Adobe support this morning I was told that you can't run a 64 bit version of ColdFusion with a 32 bit web server. In essence, the web server software and the ColdFusion server software must be the same - either 32 or 64 bit.
Apache is only officially released as a 32 bit version, but there is a 64 bit unofficial version available from http://www.blackdot.be/?inc=apache/binaries, so I downloaded that and installed it, based on the instructions at http://www.elxis.org/guides/developers-guides/64bit-apache-php-mysql-windows.html.
Once I'd installed the 64bit version of Apache, the installation of Coldfusion 9 64 bit went smoothly and all appears to be working just fine now (well, I can get to the ColdFusion Administrator page and I have successfully updated the server software to ColdFusion 9.0.1).
The fact that you can't mix different 'bit' versions of software in this way may be obvious, but it wasn't obvious to me. Having been an early adopter of a 64 bit version of Vista on my own PC, I never experienced these kind of problems before. Software installed itself into the corresponding locations on my PC without any problem and just worked. This is the first time I've run into this problem.
Unfortunately, there doesn't appear to be any information regarding this very important requirement on the system requirements pages, so I suggested to the support engineer that he may want to make the recommendation that the page is amended to clarify the situation: e.g.
IMPORTANT: 64 bit versions of ColdFusion require 64 bit versions of web server software to function. You can not mix 32 bit and 64 bit versions of web servers and ColdFusion server.
Hope this helps someone else out.

Is there any difference in the prompts of UCCX 7 (Windows based) and UCCX 9 (Linux based) ?

Are the prompts for UCCX 7 (windows based) and UCCX 9 (Linux Based) are different ?
There are no default prompts available in the script editor folder of UCCX 9.
I have downloaded some prompts from the internet with .wav format, but those prompts are not working.
Can someone tell me if the prompts are different and if they are really different, where to get those prompts then ?
I have also attached the prompts i have downloaded from the internet.

Nope, there's no difference. UCCX uses either G711 or G729 encoded files. You have to encode them first before you upload them. UCCX will not encode them like CUCM does for MOH files. In fact, you can use CUCM's MOH file encoding to encode your files for use within UCCX.
Also, you will not see the system prompts on your workstation where you installed the script editor.
What is it that you are trying to do?
Anthony Holloway
Please use the star ratings to help drive great content to the top of searches.

WL on Soalris and Apache on Linux

Similar Messages

Maybe you are looking for