WLAN and N80

Hi!
I just bought my new N80 on monday and was very excited about the WLAN feature. (That was the main reason I had when compared to N73)
But.. When I came home and should try the WLAN feature the phone only returned "Internal WLAN Error". If I tried again to connect (or some other functionality too dont remember what) the phone rebooted itself. This happend all the time. I went back to the store with the phone and received a new one today to try, but the same problem with that phone.
Does anyone knows whats wrong? Is there any hidden logs on the phone that can help me further?
My WLAN:
- Netgear WGT624Tv2 (Firmware V4.2.10_1.0.1)
- MAC Restrictions (Yes, my phone is added)
- WPA-PSK (this is a key with localized chars, could that be a problem?)
I give this phone a try until friday, if I don't get it to work by then, I most probarly will change it to an N73 to avoid frustration.
Thanks,
--Rune

Hi! I'd just tested to remove the localized chars and other chars i'd suspected, and yes, the telephone is not reporting Internal WLAN error anymore.. But sadly the story it's not over there
After lots of testing it would still not work.. After some testing the problem appeared as a quite irritating bug in the phone.
When writing *#62209526# to retrieve the mac key the telephone reports wrong!
The telephone reported: **:01:6b:c8:42:**
While the correct was: **:16:bc:84:02:**
(the stars indicates equal numbers)
This is quite a serious bug and cause lots of testing sadly..
But now, when this is discovered the LAN works as expected. So.
My advise:
- Do NOT use localized chars in the WPA-PSK key
- If you relay on MAC control, do not rely on the reported mac from the device.. Run your wlan router/switch without MAC control to retrieve the correct MAC address...
Cheers,
--Rune

Similar Messages

Windows 7 Ultimate (64-Bit) fresh install, only WLAN and video driver installed but EXTREMELY slow internet connection...

I recently checked my internet connection on my Asus G53SW and found that it was extremely slow on both the LAN and WLAN connections. I checked with a different laptop (old HP Pavilion) and I get a steady 74mbps+ connection using the same LAN cable and
also with the WLAN connection. My ISP has checked their side and everything is fine.
To try and resolve the issue I tried uninstalling, disabling and tweaking various software and even tried safe mode with networking, all to no avail. I then decided to do a complete fresh install this afternoon. I have installed Windows 7 Ultimate (64 bit)
successfully onto my SSD and everything went smoothly. I have now only installed Nvidia video drivers and the (only) WLAN driver from the Asus support site.
My WLAN connection remains incredibly slow (amost half what it is on the HP and my MacBook Pro). Clearly this is an issue with either the Asus laptop or Windows but I don't know how to proceed in order to eliminate which it could be other than to try a different
o/s to W7-Ult.
Can anyone help who knows more about this than me? Perhaps someone who has had a similar or the same problem because this is giving me a severe headache!
Thanks in advance to all and for any advice.
<script id="ncoEventScript" type="text/javascript">function DOMContentLoaded(browserID, tabId, isTop, url) { var object = document.getElementById("cosymantecnisbfw"); if(null != object) { object.DOMContentLoaded(browserID,
tabId, isTop, url);} }; function Nav(BrowserID, TabID, isTop, isBool, url) { var object = document.getElementById("cosymantecnisbfw"); if(null != object) object.Nav(BrowserID, TabID, isTop, isBool, url); }; function NavigateComplete(BrowserID, TabID,
isTop, url) { var object = document.getElementById("cosymantecnisbfw"); if(null != object) object.NavigateComplete(BrowserID, TabID, isTop, url); } function Submit(browserID, tabID, target, url) { var object = document.getElementById("cosymantecnisbfw");
if(null != object) object.Submit(browserID, tabID, target, url); }; </script>

Thank you for responding. As I stated in my original post the reason I went through this process was because of an extremely slow internet connection from both the WLAN and LAN connections on my G53SW. At that time I had all of the correct drivers on the
machine. Whilst I would agree that with the machine only having a video and WLAN driver it may well not be working 'optimally', the rationale for doing this was to get the machine working with the minimum of processes to show that it was not anti-virsu software,
Steam or the like causing interference.
I have changed out both of the HDDs this evening (a primary SSD and a secondary 1Tb HDD) for a clean hybrid 1Tb Seagate drive. Once I have installed all of the Asus drivers (and nothing else) I will try the speed test again and report back.
I can now report that with a fresh install of Windows 7 Ultimate SP1 and ONLY Asus drivers as supplied the issue remains. On a connection where I should see around 75mbps I am actually getting around 18mbps, sometimes considerably slower. This only affects
my Asus machine.
<script id="ncoEventScript" type="text/javascript">function DOMContentLoaded(browserID, tabId, isTop, url) { var object = document.getElementById("cosymantecnisbfw"); if(null != object) { object.DOMContentLoaded(browserID,
tabId, isTop, url);} }; function Nav(BrowserID, TabID, isTop, isBool, url) { var object = document.getElementById("cosymantecnisbfw"); if(null != object) object.Nav(BrowserID, TabID, isTop, isBool, url); }; function NavigateComplete(BrowserID, TabID,
isTop, url) { var object = document.getElementById("cosymantecnisbfw"); if(null != object) object.NavigateComplete(BrowserID, TabID, isTop, url); } function Submit(browserID, tabID, target, url) { var object = document.getElementById("cosymantecnisbfw");
if(null != object) object.Submit(browserID, tabID, target, url); }; </script>

I have a dv8t-1000 and the wlan and treble keep going on and off. I loose the wireless connection.

I need to know how to open the laptop to replace the card that controls the wlan and treble. I tried to find a manual to show how to get the laptop open and then be able to get the card number so I can order one. I have removed the screws but can't get it appart. Can you tell me the type of card that I would need to resolve the problem so I don't loose the wireless conection every 5 minutes.
Thanks
highdiver

The Maintenance and Service guide, which you can find here, can show you how to replace your wlan card.
I am an employee of Hewlett Packard.
- - Please mark Accept As Solution if it solves your problem so others can more easily find the answer - -
- - Please click the Kudos star if you would like to say thanks - -

Belle: No WLAN and Packet Data log.Filter options ...

In Nokia N8, with Symbian Anna, WLAN and Packet Data logging wasn't possible, even though there were options in the log filtering settings.
See below:
http://i44.tinypic.com/9kxbfa.png
After updating to Belle, log isn't still working, and both WLAN and Packet Data options were removed from filter options.
http://tinypic.com/r/6dxwgg/5
Will it be implemented in a further time?
Best Regards

Hi,
quick update on this one as we now have a FAQ online.
Q: How can I get a WLAN/Wifi and packet data filter with Nokia Belle?
A: There is no data filter included in Nokia Belle by default, but you can download specific apps from Nokia Store.
BR,
yvonne

Guest WLAN and Web Auth?

Hi Guys,
Maybe someone can help me out?
I just finished setting up a trial "Cisco Virtual Wireless Controller" with nearly the same configuration as our Physical
"Cisco Wireless Controller" with the exception of having 2 ports. Anyhow, I managed to get everything working except for the WEB AUTH on the Guest WLAN. When a client connects, he gets a DHCP address from our ASA but when we try to get to a website, we never reach the WEB AUTH page.
What I tried so far is..
add a DNS Host Name to the virtual interface and assign it to our internal DNS server.dns name was resolving but we were unable to ping 1.1.1.1
changed the virtual ip from 1.1.1.1 to 2.2.2.2 and modified the DNS entrydns name resoved but still could not ping 2.2.2.2(I think this is normal)
changed the virtual IP to a private address of 192.168.102.1 and modified the dns entrysame result
I've attached some screenshots of our configuration.

Troubleshooting Web Authentication
After you configure web authentication, if the feature does not work as expected, complete these
troubleshooting steps:
Check if the client gets an IP address. If not, users can uncheck
DHCP Required
on the WLAN and
give the wireless client a static IP address. This assumes association with the access point. Refer to
the
IP addressing issues
section of
Troubleshooting Client Issues in the Cisco Unified Wireless
Network for troubleshooting DHCP related issues
1.
On WLC versions earlier than 3.2.150.10, you must manually enter
https://1.1.1.1/login.html
in
order to navigate to the web authentication window.
The next step in the process is DNS resolution of the URL in the web browser. When a WLAN client
connects to a WLAN configured for web authentication, the client obtains an IP address from the
DHCP server. The user opens a web browser and enters a website address. The client then performs
the DNS resolution to obtain the IP address of the website. Now, when the client tries to reach the
website, the WLC intercepts the HTTP Get session of the client and redirects the user to the web
authentication login page.
2.
Therefore, ensure that the client is able to perform DNS resolution for the redirection to work. On
Windows, choose
Start > Run
, enter
CMD
in order to open a command window, and do a nslookup
www.cisco.com" and see if the IP address comes back.
On Macs/Linux: open a terminal window and do a nslookup www.cisco.com" and see if the IP
address comes back.
If you believe the client is not getting DNS resolution, you can either:
Enter either the IP address of the URL (for example, http://www.cisco.com is
http://198.133.219.25)
♦
Try to directly reach the controller's webauth page with
https:///login.html. Typically this is http://1.1.1.1/login.html.
♦
Does entering this URL bring up the web page? If yes, it is most likely a DNS problem. It might also
be a certificate problem. The controller, by default, uses a self−signed certificate and most web
browsers warn against using them.
3.
For web authentication using customized web page, ensure that the HTML code for the customized
web page is appropriate.
You can download a sample Web Authentication script from Cisco Software Downloads. For
example, for the 4400 controllers, choose
Products > Wireless > Wireless LAN Controller >
Standalone Controllers > Cisco 4400 Series Wireless LAN Controllers > Cisco 4404 Wireless
LAN Controller > Software on Chassis > Wireless Lan Controller Web Authentication
Bundle−1.0.1
and download the
webauth_bundle.zip
file.
These parameters are added to the URL when the user's Internet browser is redirected to the
customized login page:
4.
ap_mac The MAC address of the access point to which the wireless user is associated.
♦
switch_url The URL of the controller to which the user credentials should be posted.
♦
redirect The URL to which the user is redirected after authentication is successful.
♦
statusCode The status code returned from the controller's web authentication server.
♦
wlan The WLAN SSID to which the wireless user is associated.
♦
These are the available status codes:
Status Code 1: "You are already logged in. No further action is required on your part."
♦
Status Code 2: "You are not configured to authenticate against web portal. No further action
is required on your part."
♦
Status Code 3: "The username specified cannot be used at this time. Perhaps the username is
already logged into the system?"
♦
Status Code 4: "You have been excluded."
♦
Status Code 5: "The User Name and Password combination you have entered is invalid.
Please try again."
♦
All the files and pictures that need to appear on the Customized web page should be bundled into a
.tar file before uploading to the WLC. Ensure that one of the files included in the tar bundle is
login.html. You receive this error message if you do not include the login.html file:
Refer to the Guidelines for Customized Web Authentication section of Wireless LAN Controller Web
Authentication Configuration Example for more information on how to create a customized web
authentication window.
Note:
Files that are large and files that have long names will result in an extraction error. It is
recommended that pictures are in .jpg format.
5.
Internet Explorer 6.0 SP1 or later is the browser recommended for the use of web authentication.
Other browsers may or may not work.
6.
Ensure that the
Scripting
option is not blocked on the client browser as the customized web page on
the WLC is basically an HTML script. On IE 6.0, this is disabled by default for security purposes.
7.
Note:
The Pop Up blocker needs to be disabled on the browser if you have configured any Pop Up
messages for the user.
Note:
If you browse to an
https
site, redirection does not work. Refer to Cisco bug ID CSCar04580
(registered customers only) for more information.
If you have a
host name
configured for the
virtual interface
of the WLC, make sure that the DNS
resolution is available for the host name of the virtual interface.
Note:
Navigate to the
Controller > Interfaces
menu from the WLC GUI in order to assign a
DNS
hostname
to the virtual interface.
8.
Sometimes the firewall installed on the client computer blocks the web authentication login page.
Disable the firewall before you try to access the login page. The firewall can be enabled again once
the web authentication is completed.
9.
Topology/solution firewall can be placed between the client and web−auth server, which depends on
the network. As for each network design/solution implemented, the end user should make sure these
ports are allowed on the network firewall.
Protocol
Port
HTTP/HTTPS Traffic
TCP port 80/443
CAPWAP Data/Control Traffic
UDP port 5247/5246
LWAPP Data/Control Traffic
(before rel 5.0)
UDP port 12222/12223
EOIP packets
IP protocol 97
Mobility
UDP port 16666 (non
secured) UDP port 16667
(secured IPSEC tunnel)
10.
For web authentication to occur, the client should first associate to the appropriate WLAN on the
WLC. Navigate to the
Monitor > Clients
menu on the WLC GUI in order to see if the client is
associated to the WLC. Check if the client has a valid IP address.
11.
Disable the Proxy Settings on the client browser until web authentication is completed.
12.
The default web authentication method is PAP. Ensure that PAP authentication is allowed on the
RADIUS server for this to work. In order to check the status of client authentication, check the
debugs and log messages from the RADIUS server. You can use the
debug aaa all
command on the
WLC to view the debugs from the RADIUS server.
13.
Update the hardware driver on the computer to the latest code from manufacturer's website.
14.
Verify settings in the supplicant (program on laptop).
15.
When you use the Windows Zero Config supplicant built into Windows:
Verify user has latest patches installed.
♦
Run debugs on supplicant.
♦
16.
On the client, turn on the EAPOL (WPA+WPA2) and RASTLS logs from a command window, Start
> Run > CMD:
netsh ras set tracing eapol enable
netsh ras set tracing rastls enable
In order to disable the logs, run the same command but replace enable with disable. For XP, all logs
will be located in C:\Windows\tracing.
17.
If you still have no login web page, collect and analyze this output from a single client:
debug client
debug dhcp message enable
18.
debug aaa all enable
debug dot1x aaa enable
debug mobility handoff enable
If the issue is not resolved after you complete these steps, collect these debugs and use the TAC
Service Request Tool (registered customers only) in order to open a Service Request.
debug pm ssh−appgw enable
debug pm ssh−tcp enable
debug pm rules enable
debug emweb server enable
debug pm ssh−engine enable packet

GPS not available only WLAN and Basestations

Hello,
in my iPhone 4s GPS is not available, only WLAN and Basestations are used to show location on Maps. On my iPhone 4 everything works fine. Both on iOS 6.0.1
Device already reseted.
What else do I have to do.
Best regards
Reiner

I've had limited success using G spot (App from the Apple store) which seems to find my location by using my WIFI which is also registered with Skyhook and then using it to launch maps. Even though G spot works, google maps still doesn't locate me, but luckily G spot will place a pin drop on your location within maps at the touch of a button.
Thus this may be a workaround for now. G spot also seems seems to work with my wifi off, but I don't know if it's just using a cache of my last known location. I haven't tested in places aside from my flat yet, but will do so very shortly and I will report back whether using a third party app, such as G spot works at obtaining your location which can then be feed into google maps.
Gspot is not free (though it's not expensive). Luckily I had it due to the compass it provides. However one can test whether 3rd party apps work for you or not in obtaining your location for free by downloading either of the 'here i am' apps from iTunes and having it email your location to yourself and then opening the link from the email, which launches maps and pin drops your location. Though this will not provide live GPS on the 3G, but it will atleast give you a general location and a map if you're lost until Apple sorts out their ****!

Guest WLAN and a Office WLAN on 1242AG

Hi All,
I have managed to add two WLANS, one for the Office Wireless clients(Staff laptops) and another one for Guests. I have bassicaly created two SSIDs, one broadcasting, other one not(Staff one).
The AP is a 1242AG and is going to connect to a Catalyst 3750 48T, which is connected to Cisco 877. How can I make the DHCP assignments to both Guest WLAN and Staff WLAN and also do I have to create trunk port in the Switch ( I am thinking like this as I got Two VLANs.)
Does anyone know or got a sample running config ( in a Switch and in a similar AP)...really appriciate it. Time is running out for me!!!
Reg
ND

Hi,
here is a config example for exactly you are looking for:
http://www.cisco.com/en/US/tech/tk722/tk809/technologies_configuration_example09186a0080665ceb.shtml.
HTH,
Tiago

Vista x64 drivers for Broadcom BCM4311 wlan and touchpad

Hello!
Where to download a Vista x64 driver for a Broadcom BCM4311 wlan and touchpad for a Lenovo 3000 G410m-mm? A Windows update wlan driver allows a two times slower speed.
Regards,
Dmitry

Try this.
//help will save the world

No wlan and bluetooth after recovery

WLAN and Bluetooth is lost after I took my ipod touch through a receovery procedure

Here is Apple's article for that symptom. You may end up making an appointment at the Genius Bar of an Apple store since sometime the steps do not fix the problem.
Unable to use Wi-Fi or Bluetooth with iPhone or iPod touch because there's no address listed for the device

5530XM disconnecting from WLAN and not showing hom...

My 5530XM is acting up again (v.11 firmware). The symtopms are random disconnects from WLAN and, after doing a soft reset, unable to put shortcuts on the home screen (using the Shortcuts theme).
I really think the problem is with the memory card because I can't turn the phone on with the card inside.
Is there a way to scan/repair problems with the memory card? I really, really want to avoid a hard reset. Last time I did that, I lost all my apps from the memory card (I have the Games Edition).
I can try using PC Suite or Ovi Suite to back up my memory card apps, but I don't trust the suites that much. What I'd like to do is drag and drop my memory card apps to another location in my PC, but I cannot see the memory card apps in Windows Explorer.
Does anyone have any suggestions?
Solved!
Go to Solution.

I backed up my data. Although my dialer shortcut stopped working, doing the red/green/camera trick allowed me to dial *#7370# . By the way, I had removed my memory card prior to dialing *#7370#.
Looks like things are working better (dialer works), but my new concern is that when I put the memory card back in, I get "preparing memory card." This freaks me out because last time I saw that, I lost ALL the games that came preinstalled on the 5530 (Games Edition). I understand that I backed up my files, but I have this weird feeling that the games don't get backed up. I pulled the memory card out, put it inside an SD adapter and there are readable files in there, but the preinstalled games may be hidden.
Where are the preinstalled apps on the memory card? I just want to back them up manually, to have peace of mind.
I used PC Suite, by the way.
Thanks for all the help.

DNS Registration for clients with WLAN and LAN adapters

I have read a number of articles and it seems that there are a number of people who have problems with DNS and workstations with both WLAN and LAN adapters. I haven't however found workable solutions.
Workstation Connection Objective:
To enable DNS discovery and Ip connection to client workstations regardless of whether the client is using the WLAN or LAN. Enabling users to use either Wireless or LAN adapter adhoc. ie they dock their laptops at their desks, and undock to take their laptops
to meetings or consulations with peers. I need to be able to discover and connect to the workstations irrespective of the adapter being used at any time.
Most people seem to try to control which interface is used on the workstations, ie disable WLAN and only use LAN etc. Trying to disable interfaces isn't going to be feasible and its very inflexible.
I believe I can ensure that the workstations use the NICs in our preferred order:
1. LAN
2. WLAN - Our wireless network isn't as fast as the LAN.
By setting specific DHCP metric for the WLAN Router to be higher(ie 2) than the LAN(1). When the LAN isn't connected traffic will route via the WLAN adapter and when the LAN adapter is connected, its router metric will be lower and it will be the preferred
gateway/route.
But how do I solve the DNS resolution for connection to that asset?
If I disable DHCP Server updates into DNS and allow secure updates from the client. It would be really good if DNS client behaved in the following manner
1. The LAN adapter(referred to as primary ie LAN) with the lowest metric(ie 1) registers/auto updates DNS with the ip(both A and PTR). Any other Adapters don't register. - ie the WLAN
2. The Laptop is undocked and the LAN adapter goes offline, the DNS Client then triggers a registration/auto updates its existing DNS entry with the ip from the next adapter(WLAN) with the next lowest gateway metric(2)...hence replacing the first ip registered.
3. The laptop is docked again, and DNS Client triggers a registration/auto updates its existing DNS entry with the IP from the primary adapter(LAN), replacing the WLAN ip.
So there is only ever 1 ipaddress registered for a workstation and it will always be a valid address. Then I don't need to be concerned about whether the user has the wireless turned on and docked.
Being able to discover and communicate with all our workstations in our sites is crucial requirement....
This microsoft article says, http://technet.microsoft.com/en-gb/library/cc771255.aspx
Dynamic updates can be sent for any of the following reasons or events:
    * An IP address is added, removed, or modified in the TCP/IP properties configuration for any one of the installed network connections.
    * An IP address lease changes or renews with the DHCP server any one of the installed network connections. For example, when the computer is started or if the ipconfig /renew command is used.
    * The ipconfig /registerdns command is used to manually force a refresh of the client name registration in DNS.
    * At startup time, when the computer is turned on.
    * A member server is promoted to a domain controller.
However from what I am reading, both adapters(LAN,WLAN), if configured to update DNS, will register their Ip addresses. Which leads to an invalid DNS entry if the laptop is undocked, as the IP for LAN adapter isn't removed.
Has anyone solved this problem for their organizations without
1. Controlling which adapter is used - large management overhead
2. Only allowing one adapter to register with DNS
   - If using LAN adapter for DNS, then anytime the user is using WLAN, their workstation doesn't have a valid DNS entry. Which also impacts Kerberos.
   - If using the WLAN, then we would have to invest a large amount of money into Wireless to provide the necessary bandwidth
3. Setting GPO's to configure dns updates every 30mins on clients
   - Inconsistent results...which I think is sometimes a worse problem
4. Defining separate DNS suffixes for their WLAN networks (I read some people did this)
   - This doesn't remove an invalid DNS entry ie the ip(LAN adapter) DNS entry if the laptop is undocked
   - It also creates problems with kerberos, if the host is registered under a separate DNS suffix from the Active Directory domain name

Hi,
From my point of view, DNS can't be so smart.
As a workaround, please try the steps below,
Disable the DNS register of wireless adapter
Put "ipconfig /regiserdns" in a bat file
Everytime when the wired network is undocked, run the bat file.
If the wired network is docked, wired adapter will register the DNS record.
When the wired network is undocked, run the bat file, then the wireless adapter will register the DNS record.
If the wired network is docked again, wired adapter will register the DNS record automatically.
Best Regards.
Steven Lee
TechNet Community Support

I just started my Macbook air the first time, connected it with my wlan and know it asks me for a password and it does not accept the only password I know, what can I do?

I just started my Macbook air the first time, connected it with my wlan and know it asks me for a password and it does not accept the only password I know, what can I do?

It needs the user password for the wireless router, that would have been set by whomever installed the router, if that was you then try to find the password. If you can not find the password reset the router to factory default and set it up again.

Hi, i bought second hand iphone 3 GS and wanted to switch it free over wlan and over itunes (windows), i tried many times but seems not to be possible.

hi, i bought second hand iphone 3 GS and wanted to switch it free over wlan and over itunes (windows), i tried many times but seems not to be possible.
Under itunes i made also the available tests, the connection always fails with the message that there is no secure connection to the apple server.....
any suggestions? Thks i advance

This Looks as if your phone has been hacked.

Accessing WLAN with N80 failed

Hi all,
I'm trying to let my N80 IE connect to my offices WLAN. While trying to connect I got a "WPA verification failed". Does anyone know the reason for this failure?
Abel
Background:
I have been playing around with the settings. I added a new 'Access Point' for my office, and set its 'WLAN security mode' to WPA/WPA2. Entering the 'WLAN Security sett.' I entered:
- WPA mode: EAP
- EAP plug-in settings: EAP-PEAP (deselected what was already there, and moved EAP-PEAP to the top)
- TKIP encryption: not allowed (we do not use a temporal key)
EAP-PEAP is configured as:
- User certificate: not defined
- CA certicicate: not defined (our certificate is not in the list, we use a private one)
- User name in use: from certificate
- User name: my user name as used on the office domain
- Realm in use: user configured
- Realm: the domain as used in the office
- Allow PEAPv0 .. v1: all yes
EAP-MSCAPv2 is configured as:
- User name: my user name as used on the office domain
- Prompt password: yes
- Password: the password used to log in into the office domain
A colleague checked the log file when I tried to log in, and no entry existed for a mobile trying to access the wlan.

WPA and EAP works great with the N80 - dont worry
I have tested and runs alot og Nokia Phones with WiFi and EAP etc.
I currently uses a N80 fw 4.0707.0.7, and there are a v5 fw also.
I sugguest you get the 4.07
You subject informs about WPA but you have set your Security mode: 802.1x
Change this to:
Security mode: WPA/WPA2
Then you should be good.
Also verify the status: hidden/public this is important
If you can see the SSID in the WLAN Wiz then its public SSID.
Try clearing the username in the certificate setup/PEAP
also try different comination of DOMAIN/USERNAME, DOMAIN\USERNAME, DOMAIN@USERNAME etc
But I would think that you do not need username in the GENERAL page under EAP-PEAP
You need username under EAP page/EAP-MSCHAPv2
I assume you have the certificate installed on the handset.
HTH

Wlan on N80 problems!

Hi! I have noticed some problems with the N80s Wlan capabilities! Sometimes i have no problem what so ever to connect to a Wlan, i just choose the connectionpoint from the list connecting to a webpage and it connects. However, several times now it wont connect. I choose the connection point and it tryes to connect, but after a few seconds i receive a error message where it says something like; the wlan could not be found! This happens both when there is a WEP encryption (and i have the key) and also where there is no encryption. I have tried this on atleast 10 different W-lan networks, the only one that worked was my neighbours, until he put on WEP encryption
The other networks have been in town in different malls and cafe´s and so on and have all been free networks to use. So my question is, is there any easy way to configure the phone to be receptive to most Wlans or do i as a connecting user have to set up each connection point manually, even if i dont know what the settings should be? I could include that i have called nokia about this, and not very surpricingly they told me that they can only inform me about the basic phone settings, everything else such as connecting to a Wlan, have to be done by my self, gahh!
Cheers all!

Just out of curiosity, remove the security from your router and see if the N80 sees it.

WLAN and N80

Similar Messages

Maybe you are looking for