WLAN client dropping problem
My customer is using WLC4400(4.0.179.11) and LAP1130(12.3jx1). Before converting IOS to LWAPP, the WLAN service is not problem.
But after changing to LWAPP based,the customer is complain about disconnecting problem.
Intel centrino and other vendor's wlan cards are dropping, cisco wlan cards are no problem.
After all we have to fall back to IOS version. Is there any Bug report about WLC4400?
There are some issues with the Intel adapters. I would try downloading the latest driver version to see if that helps. You can navigate to the Intel support page and view the documented disconnect issues.
-Mark
Similar Messages
-
WRVS4400N v2 WLAN clients dropping
I purchased a WRVS4400N for my home to replace an older router. Since I started using the Cisco router, WLAN clients drop. I can sometimes get them back after initiating a ping to a static LAN IP, but it takes a few seconds.
This issue impacts Win Vista, Win7, Mac, Android, and Linux machines...so basically anything that does WiFi. There seem to be many complaints here with no resolution. Has anyone fixed this problem in their network? I'd really hate to return this thing, but it's becoming unusable.Mr. Cameron,
Hi, My name is Eric Moyers. I am a Network Support Engineer in the Cisco Small Business Support Center. I am truly sorry to hear about your issue you are having with your router.
Have you called into the Small Business Support Center for help on this? If you have may I have your case number so that I can pull your case and review it to see if there is anything I can do for you.
If you have not called in, I would like to strongly encourage you to call in and get a case created and let one of our agents help you with this issue. THe WRVS4400N is a very good router and I want to make sure that we do everything we can to keep your business.
Thanks
Eric Moyers
Cisco Network Support Engineer
1-866-606-1866 -
Cisco 876w: wlan client - routing problem
I configured a Cisco 876w to connect to an existing WLAN as a client. Now I would like to connect 3 PCs to the 876w which should be able to access the internet via the 876w.
Problem:
Being at the console (ssh) of the 876w, I can ping hosts in the internet (even with their name like www.google.com) but when I'm using a client PC, I can't... What am I missing here? Could it be a NAT problem?
Config:
Internet <---> DSL Router 192.168.1.1 (and WLAN AccessPoint) <---> Cisco 876w (gets IP per DHCP, VLAN1 IP: 10.10.10.1) <---> PC (10.10.10.101)
Current configuration : 9897 bytes
version 12.4
no service pad...dot11 vlan-name wlan-lan vlan 1
dot11 ssid WLAN
vlan 1
authentication open
authentication key-management wpa
wpa-psk ascii 7 0923467F1B2E52789807132F7A202E3D31
no ip source-route
ip dhcp excluded-address 10.10.10.1 10.10.10.9
ip dhcp excluded-address 10.10.10.101 10.10.10.254
ip dhcp pool ccp-pool1
import all
network 10.10.10.0 255.255.255.0
default-router 10.10.10.1
domain-name cisco.test.com
dns-server 208.67.222.222
ip cef
no ip bootp server
ip domain name test.com
ip name-server 208.67.222.222ip ddns update method sdm_ddns1
HTTP
add http://[email protected]/nic/update?system=dyndns&hostname=//[email protected]/nic/update?system=dyndns&hostname=<h>&myip=<a>
remove http://[email protected]/nic/update?system=dyndns&hostname=//[email protected]/nic/update?system=dyndns&hostname=<h>&myip=<a>
no ipv6 cef
multilink bundle-name authenticated
isdn switch-type basic-net3
username admin privilege 15 secret 5 $1$uiouLKjbLIUBlKbj
username service privilege 15 secret 5 $1$LKjblkJNBLKkjlbkm
archive
log config
hidekeys
ip tcp synwait-time 10
ip ssh time-out 60
ip ssh authentication-retries 2
class-map type inspect match-all sdm-cls--1
match access-group name AllowAny
policy-map type inspect sdm-policy-sdm-cls--1
class type inspect sdm-cls--1
inspect
class class-default
drop
zone security wan
zone security lan
zone-pair security sdm-zp-lan-wan source lan destination wan
service-policy type inspect sdm-policy-sdm-cls--1
interface BRI0
description <--
no ip address
ip flow ingress
ip virtual-reassembly
encapsulation ppp
shutdown
dialer pool-member 1
isdn switch-type basic-net3
isdn point-to-point-setup
ppp multilink!
interface ATM0
backup interface BRI0
no ip address
no ip redirects
no ip unreachables
no ip proxy-arp
ip flow ingress
shutdown
no atm ilmi-keepalive
interface ATM0.3 point-to-point
description <--
ip flow ingress
shutdown
pvc 1/32
pppoe-client dial-pool-number 2
interface FastEthernet0
interface FastEthernet1
interface FastEthernet2
interface FastEthernet3
interface Dot11Radio0
description <--
no ip address
no ip proxy-arp
ip flow ingress
ip virtual-reassembly
no ip route-cache cef
no ip route-cache
encryption mode ciphers aes-ccm
encryption vlan 1 mode ciphers aes-ccm
ssid WLAN
speed basic-1.0 basic-2.0 basic-5.5 6.0 9.0 basic-11.0 12.0 18.0 24.0 36.0 48.0 54.0
station-role non-root
no cdp enable
interface Dot11Radio0.1
encapsulation dot1Q 1 native
ip address dhcp
ip nat outside
ip virtual-reassembly
no ip route-cache
no cdp enable
interface Vlan1
description $ETH-SW-LAUNCH$$INTF-INFO-HWIC 4ESW$$ES_LAN$$FW_INSIDE$
ip address 10.10.10.1 255.255.255.0
no ip redirects
no ip unreachables
no ip proxy-arp
ip flow ingress
ip nat inside
ip virtual-reassembly
zone-member security lan
ip tcp adjust-mss 1412
interface Dialer0
ip ddns update hostname blahblah.dnsalias.com
ip ddns update sdm_ddns1
ip address negotiated
ip nat outside
ip virtual-reassembly
zone-member security wan
encapsulation ppp
shutdown
dialer pool 1
dialer idle-timeout 600
dialer string 01919214124
dialer load-threshold 20 outbound
dialer watch-group 1
dialer-group 1
no cdp enable
ppp authentication chap pap callin
ppp chap hostname asfa
ppp chap password 7 128763520
ppp pap sent-username asfa password 7 0302141555
ppp multilink
interface Dialer2
ip ddns update sdm_ddns1
ip address negotiated
ip mtu 1452
ip nat outside
ip virtual-reassembly
zone-member security wan
encapsulation ppp
dialer pool 2
dialer-group 2
no cdp enable
ppp authentication chap pap callin
ppp chap hostname gast
ppp chap password 7 095B239876473F06090A
ppp pap sent-username gast password 7 1239847629873693D
router rip
network 10.0.0.0
ip forward-protocol nd
ip route 0.0.0.0 0.0.0.0 192.168.1.1
ip http server
ip http access-class 23ip http authentication local
ip http secure-server
ip http timeout-policy idle 60 life 86400 requests 10000
ip nat inside source list 105 interface Dialer0 overload
ip nat inside source list 106 interface Dot11Radio0.1 overload
ip access-list extended AllowAny
remark CCP_ACL Category=128
permit ip 10.10.10.0 0.0.0.255 any
ip access-list extended nix
remark tut nix
remark CCP_ACL Category=2
permit tcp any any
permit udp any any
permit icmp any any
permit ip any any
logging trap debugging
access-list 1 remark INSIDE_IF=Vlan1
access-list 1 remark CCP_ACL Category=2
access-list 1 permit 10.10.10.0 0.0.0.255
access-list 100 remark CCP_ACL Category=2
access-list 100 permit ip any any
access-list 101 remark CCP_ACL Category=2
access-list 101 permit ip 10.10.10.0 0.0.0.255 any
access-list 102 remark CCP_ACL Category=2
access-list 102 permit ip 10.10.10.0 0.0.0.255 any
access-list 103 remark CCP_ACL Category=2
access-list 103 permit ip 10.10.10.0 0.0.0.255 any
access-list 105 remark Alles
access-list 105 remark CCP_ACL Category=2
access-list 105 permit ip 10.10.10.0 0.0.0.255 any
access-list 105 permit icmp 10.10.10.0 0.0.0.255 any
access-list 105 permit udp 10.10.10.0 0.0.0.255 any
access-list 105 permit tcp 10.10.10.0 0.0.0.255 any
access-list 106 remark NAT wlan
access-list 106 remark CCP_ACL Category=2
access-list 106 permit ip 10.10.10.0 0.0.0.255 any
access-list 106 permit icmp 10.10.10.0 0.0.0.255 any
access-list 106 permit udp 10.10.10.0 0.0.0.255 any
access-list 106 permit tcp 10.10.10.0 0.0.0.255 any
dialer watch-list 1 ip 208.67.222.222 255.255.255.255
dialer-list 1 protocol ip permit
no cdp run
radius-server attribute 32 include-in-access-req format %h
radius-server vsa send accounting
control-plane
banner exec ^C
% Password expiration warning.
Cisco Configuration Professional (Cisco CP) is installed on this device
and it provides the default username "cisco" for one-time use. If you have
already used the username "cisco" to login to the router and your IOS image
supports the "one-time" user option, then this username has already expired.
You will not be able to login to the router with this username after you exit
this session.
It is strongly suggested that you create a new username with a privilege level
of 15 using the following command.
username <myuser> privilege 15 secret 0 <mypassword>
Replace <myuser> and <mypassword> with the username and password you
want to use.
^C
banner login ^CAuthorized access only!
Disconnect IMMEDIATELY if you are not an authorized user!^C
line con 0
no modem enable
transport output telnet
line aux 0
transport output telnet
line vty 0 4
transport input telnet ssh
scheduler max-task-time 5000
scheduler allocate 4000 1000
scheduler interval 500
end
#sh ip int brief
ndrmedienturm#sh ip int brief
Interface IP-Address OK? Method Status Protocol
FastEthernet0 unassigned YES unset up up
FastEthernet1 unassigned YES unset up down
FastEthernet2 unassigned YES unset up down
FastEthernet3 unassigned YES unset up down
BRI0 unassigned YES NVRAM standby mode/disabled down
BRI0:1 unassigned YES unset administratively down down
BRI0:2 unassigned YES unset administratively down down
Dot11Radio0 unassigned YES TFTP up up
Dot11Radio0.1 unassigned YES DHCP up up
ATM0 unassigned YES NVRAM administratively down down
ATM0.3 unassigned YES unset administratively down down
SSLVPN-VIF0 unassigned NO unset up up
Vlan1 10.10.10.1 YES NVRAM up up
NVI0 unassigned YES unset administratively down down
Dialer0 unassigned YES NVRAM administratively down down
Dialer2 unassigned YES NVRAM up up
Virtual-Dot11Radio0 unassigned YES TFTP up up
Virtual-Dot11Radio0.1 192.168.1.54 YES DHCP up upHi,
Just check it out few things from client are you able to ping the wan interface of the cisco 876w and when you ping the internt address from client pc what is the out put of the nat translation in router.
The command to check the same is show ip nat translation is packet is gettin translated or not.
Hope to Help !!
Ganesh.H -
WLAN Clients unable to access the Gateway when more than 2 clients connect
Hi,
I have a problem with a 2106 WLAN Contoller.
The clients can connect and associate to the WLAN and get their IP details via DHCP from the internal DHCP server. However, only 2 clients can get out through the gateway at any one time. All other clients that connect will get their DHCP addresses(that match the config of the 1st 2 clients), but they cannot get to the gateway. They can ping any client on the WLAN and the controller.Hi,
Please post the IP configuration for your gateway, the working clients and the clients having problems.
Regards,
Kristofer -
Force WLAN client to renew ip on WLC with dynamic interfaces
Hi there
we would like to have a "two tier" authentication for the corporate WLAN clients:
Requirements
1. Machine Authentication
The client gets machine authenticated based on the machine account in the Active Directory with PEAP. At this stage, the client will get a IP from VLAN A. VLAN A has limited access to the corporate infrastructure (DNS, AD, some volumes / shares, and so on). The filtering is done with an IP access list on the layer 3 VLAN interface on the core switches.
2. User Authentication
The users logs in on the client and gets user authenticated based on his user account in the Active Directory with PEAP - only users with a valid Machine Access Restriction (MAR) are allowed to login. Now the client is moved to another VLAN B. VLAN B has full access to the corporate infrastructure, here is no IP access list.
Infrastructure
We have the following:
2 x WLC 5508 with 7.3.101.0
2 x ACS 5.3.0.40.6
Problem
Now we have the problem, that the Windows client sometimes takes up to 3 minutes to connect to the WLAN after the users loggs in. In the debug, I can see that this happens because the client is stuck in DHCP renewal:
1. After the machine has been authenticated it has an IP assigned from VLAN A. This works pretty well if the client gets rebooted.
2. If the user loggs in the first time after the reboot, the users gets connected within 10 seconds, what is pretty good. The client has now an IP in VLAN B.
3. Now the user logs out of Windows and I can see in the debug, that the client is putted into VLAN A (machine authentication) again, but the client still tries to DHCPREQUEST the IP address from VLAN B (user authentication). Because this request is sent out on the wrong dynamic interface on WLC, the DHCPREQUEST is not acknowleged an the client get stuck in this situation.
4. If the user or another users logs in again shortly after the logout, the client still tries to DHCPREQUEST the IP of VLAN B and now the "3 times DHCP failure on WLC" comes into play, because WLC thinks that the DHCP server is not reachable -> but it only does not answer a wrong DHCPREQUEST.
Question
On ISE there is a way to force the client to renew the DHCP address (via CoA, but this has its limitations too --> need to install Active X or Java applet). I think there is now way to force the client to renew its IP with ACS, but my question is, is there a workaround and are there any others, that maybe already solved this problem?
Alternative
If there is now way to bring this to work with two different VLAN's, I could try to realize this with only one VLAN. After the machine authentication I could apply a WLC ACL to restrict access to the corporate infrastructure. If the user authentication happens, I could "remove" this ACL to grant full access for this user / client. But I am still interested in the other solution ;-)
Thanks in advance for any advise and best regards
DominicYour second option is what you should do. Changing the vlan on a client that already has an IP address especially on wireless will not know it has been put in a different vlan and that's why it breaks. If There was a way to change the vlan and send something to the WLC to disassociate the client, that might work.
Sent from Cisco Technical Support iPhone App -
ISE Certificate Chain Not Trusted By WLAN Clients
We are running ISE 1.1.3 using Entrust cert signed by Entrust sub CA L1C, which is signed by Entrust.net 2048, which is in all major OS stores as trusted (Windows, Android, iOS).
We have installed a concatenated PEM file with all of the certificates from the chain, as described in the ISE User Guides. The ISE GUI shows all of the certs in the chain individually after the import (i.e. the chain works and is good). However, we are not sure if the ISE is sending the entire chain to the WLAN clients during EAP authentication or just the ISE cert because of the error message we get on ALL client types which state that the certifiicate is not trusted.
So the question is if the ISE is really sending the whole chain or just its own cert with out the rest of the certs in the chain (which would explain why the WLAN clients complain about the certificate trust.)
Anyone out there know if the ISE code is not up to sending the cert chain in version 1.1.3 yet or if there is some other explanation? Screenshot attached of iPhone prompting for cert verification.Thanks hardiklodhia, your post confirms what we are seeing - the Windows clients have no issue as long as they are set to either NOT validate the EAP server cert or they are set to trust the signing CA cert from the local store by specifically selecting the signing CA (i.e. tick next to "Validate Serverr Certificate" and then another tick next to the signing CA cert in the box below.)
The iOS clients ALWAYS prompt for verification (thanks Apple.)
Note: we are using 1.1.3 and the cert chain import using a concatenated PEM file with ALL of the certs in the chain works fine. We are seeing the whole chain on the clients and the ISE extracts each PEM file into its local store.
The PEM file format is not adequately described in the user guides rather a vague description of cert order is provided.
The file should look like this:
-------------------------Top of page-----------------------------
Root CA PEM FILE
Intermediate CA 1 PEM FILE
Intermediate CA 2 PEM FILE
ETC
ISE CERT PEM FILE
------------------------Bottom of page-------------------------
By "PEM FILE" I mean the actual base64 encoded PEM output from openssl when you convert a .crt or .der file to PEM, including the words "-----BEGIN CERTIFICATE-----" and "-----END CERTIFICATE-----" for each PEM FILE above,
e.g.
-----BEGIN CERTIFICATE-----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-----END CERTIFICATE-----
-----BEGIN CERTIFICATE-----
MIIEnzCCBAigAwIBAgIERp6RGjANBgkqhkiG9w0BAQUFADCBwzELMAkGA1UEBhMC
VVMxFDASBgNVBAoTC0VudHJ1c3QubmV0MTswOQYDVQQLEzJ3d3cuZW50cnVzdC5u
ZXQvQ1BTIGluY29ycC4gYnkgcmVmLiAobGltaXRzIGxpYWIuKTElMCMGA1UECxMc
VeSB0RGAvtiJuQijMfmhJAkWuXAwHwYDVR0jBBgwFoAU8BdiE1U9s/8KAGv7UISX
8+1i0BowGQYJKoZIhvZ9B0EABAwwChsEVjcuMQMCAIEwDQYJKoZIhvcNAQEFBQAD
gYEAj2WiMI4mq4rsNRaY6QPwjRdfvExsAvZ0UuDCxh/O8qYRDKixDk2Ei3E277M1
RfPB+JbFi1WkzGuDFiAy2r77r5u3n+F+hJ+ePFCnP1zCvouGuAiS7vhCKw0T43aF
SApKv9ClOwqwVLht4wj5NI0LjosSzBcaM4eVyJ4K3FBTF3s=
-----END CERTIFICATE-----
-----BEGIN CERTIFICATE-----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-----END CERTIFICATE-----
-----BEGIN CERTIFICATE-----
MIIFKjCCBBKgAwIBAgIETB9GEzANBgkqhkiG9w0BAQUFADCBsTELMAkGA1UEBhMC
VVMxFjAUBgNVBAoTDUVudHJ1c3QsIEluYy4xOTA3BgNVBAsTMHd3dy5lbnRydXN0
Lm5ldC9ycGEgaXMgaW5jb3Jwb3JhdGVkIGJ5IHJlZmVyZW5jZTEfMB0GA1UECxMW
KGMpIDIwMDkgRW50cnVzdCwgSW5jLjEuMCwGA1UEAxMlRW50cnVzdCBDZXJ0aWZp
yhHR/hYfdVM88hBXXypACgrxBv/JFlKzSEDwKydJeT1tcP//nG4jv1WWgLk6O2Mi
0oE0fnGmuf9fTX4+CdapG2gTDFJ29Chv3kavJDNtB85A7CK8oWI8Qav78Rvaz7nA
LiRMLBQ1RkqUrQFL2WHx4mJkCddPXzOeOVJlUTGJ
-----END CERTIFICATE-----
The last PEM output (the one directly above) is the ISE cert in PEM format. The first PEM output (the one at the top) is the Root CA cert in PEM format. The ones in the middle are intermediate signing CAs in order (from root to leaf). -
Problem Syncing Outlook....says outlook sync client encountered problem
I have been syncing outlook calendar and contacts from my PC to my iPhone with no problems. I have version 1.1.2 on my iPhone and 7.5 or whatever the latest is on iTunes software. The syncs were fine until recently and now I cant sync and get an error message that says "outlook sync client encountered problem" What could possibly have happened....I read some posts that say to go back to iTunes 7.3 etc....this has to be a common problem....any suggestions.
Here is an article from the apple support website that might help out.
http://docs.info.apple.com/article.html?artnum=305845 -
Drag and drop problem on Lion... doesn't work
Hi,
I have had a drag and drop problem since I installed Lion on my computer. I grab a file and by the time i try to drop it on a folder it is not released. This happens in all programs and it is really annoying, finder, iphoto, mail, you name it.
I've tried repairing disk permissions directly from lion and then from the repair disk partition and it has been no good.
Any ideas???
I have a MBP 15 in, 2.8 ghz intel core 2 duo. 4 gb ram.
And hey, since i installed lion computer is soooooooooooo slow, any tips will be highly appreciated.drag and drop doesnt work at all, no matter what i try to do it doesnt work.
on desktop i grab a file and then try to drop it on a folder and doesnt drop.
on mail i grab an e-mail and try to place it on a folder and it doesnt drop.
i movie i select some photos, try to drag them to the project area and they dont drop i have to copy/paste in order to transfer them.
itunes i grab a file from my music library and try to drop it to a playlist and it doesnt drop
it is really really annoying.
any ideas???? -
Drag and drop problem from wizard inside another drop
I am using JDK 1.5.0_11 Swing.
I am facing a Drag and Drop problem which is described below:
A drag and drop operation invokes a wizard, from which another wizard is invoked. Within one of the panels of this 2nd wizard, I am trying to do a drag and drop from a JTextarea to a JTree node, but am NOT able to. I am not getting any exceptions. I have written a transfer handler for the JTree node to handle the text transfers from a JTextArea. When I try to do a drag and drop from a JTree node to another JTree node I'm getting the 'InvalidDNDOperation: drag and drop in progress' exception.
When the 2nd wizard is invoked directly, I am able to do the drag and drop from JTextArea to a JTree node and also from a JTree node to another JTree node.
I tried spawning a new thread for the 2nd wizard, but am still unable to initiate drag and drop.
Should I be spawning a new thread for the 1st wizard?
Message was edited by:
sbandyopPlease post Swing questions in the Swing forum: http://forum.java.sun.com/forum.jspa?forumID=57
-
I am facing call drop problem (incoming
I am facing call drop problem in my I phone 5 since morning today, Outgoing & incoming both.
However i switched off the handset & also pull out SIM from the Handset, again insert & reset the functions but it's stilll not working.
Please help.Hi there Kuldeep Mishra,
You may find the troubleshooting steps in the article below helpful.
iPhone: Troubleshooting issues making or receiving calls
https://support.apple.com/kb/TS3406
-Griff W. -
Client deletion Problem - Urjent..
Hi Experts,
There is an existing DEV-QA-PRD environment. There is a need to have a complete Configuration copy of PRD in DEV2 system, which will be used to build another Production Stream (DEV2, QA2, PRD2) for another project.
When we are deleting client ,below Problems we have facing :
1) Production equivalent client (4 TB of data) is taking too much time while deleting tables (step 4 in the diagram below).
2) Of the total 34,882 tables, 34,855 tables took almost 7-8 days to delete.
3) Last 30-35 tables are taking a lot of time to delete, these are probably the largest tables in the system
4) Tables EDIDS and CDCLS are currently being deleted for the last 3-4 days
5) Adding more processes to the Dev2 system is not helping either.
6) At the current rate, these tables will take another 1.5-2 weeks, which seems to be a long time
7) Some more tables which took more time were SWWLOGHIST, IDOCREL, SRRELROLES
Other information:
1) Operating System used for the ECC 5.0 is: Tru64 / HP, Oracle 9i DB (List of Service packs and Patches are attached)
2) Production system has data worth approx. 4TB
3) No Data Archiving has been done since the inception of the system
I need your Suggestions and Comments on this ---its urjent
Points will rewarded for suitable answers
Regards
PrabhuHi Prabhakar
Any other comments Plz...
Ok, you wanted it )) here is mine
so far:
- you copied your huge database (where you don't delete / archive old data) to the new server
- you are now deleting row by row all that data
- you will end up having a still huge but empty database, because the tables / tablespaces won't shrink after the client deletion
This does not make any sense to me, am i missing something :(((
Are there other clients in the prod system, which you keep?
@ Markus: i don't think they have 100+ gb memory to cache their huge tables in the sga
I guess the client deletion has something like a MAX ROWS COMMIT limit to prevent undo overflow. If this number is for example 100'000 rows, then you have to execute 100 delete statements (-> 100 full scans) on a 10mio row table. This of course is taking ages. Even worse it gets slower and slower, because the first delete up to 100'000 rows gets the first blocks, the second scans the same blocks, but they are empty now, so it has to scan further, and so on...
Best regards
Michael
Update: i recall there was a sap note somewhere, i just checked, here it is:
365304 - CC-ADMIN: Reports for deleting tables
Edited by: mho on Jan 8, 2008 2:40 PM -
RLDP enabled on WLC causes client drops?
The release notes for WLC code 4.0.206.0 states, "Enabling RLDP may cause access points connected to the controller to lose connectivity with their
clients for up to 30 seconds." Does anyone have more information about this? I don't like the word "may" in there. I need to enable RLDP but I can't afford to have clients dropping. Is this something that will work differently in a new release?There's no may about it. If clients are on an AP that decides to go rogue-hunting they will be told to "get out of the pool" (de-authenticated) to facilitate their going elsewhere. The same applies to DCA - Dynamic Channel Allocation - part of Auto-RF. If you don't have AP density, clients that use fast roaming, or tolerant apps, you would be best served to turn these features off (or On-Damand).
-
DWCS3 Float Drop Problem?
My site passed the Browser compatibility check in DWCS3, however, after launching site online and viewing it on a IE6 PC computer, the home page does not display correctly: the center section drops down. I checked for a potential float drop problem by adding up my widths including margins and padding: Sidebar left is 170 px, main content area is 370 px (this is the area that drops), sidebar right is 180 px = 720 px. The container is 780 width so I don't understand why the center doesn't fit but drops down because there seems to be 60 px left in the overall width to provide plenty of room. The main content area doesn't have a width specified, just a left and right margins (left set at 170 and right set at 180). I didn't try a conditional comment because I am not that familiar with coding. Any suggestions would be helpful. Also, don't understand why this wasn't flagged in the DWCS3 Browser compatibility check when it scanned for IE6. The address is http://www.eastontroop66.org and it's the home page. Thank you!
My site passed the Browser compatibility check in DWCS3, however, after launching site online and viewing it on a IE6 PC computer, the home page does not display correctly: the center section drops down. I checked for a potential float drop problem by adding up my widths including margins and padding: Sidebar left is 170 px, main content area is 370 px (this is the area that drops), sidebar right is 180 px = 720 px. The container is 780 width so I don't understand why the center doesn't fit but drops down because there seems to be 60 px left in the overall width to provide plenty of room. The main content area doesn't have a width specified, just a left and right margins (left set at 170 and right set at 180). I didn't try a conditional comment because I am not that familiar with coding. Any suggestions would be helpful. Also, don't understand why this wasn't flagged in the DWCS3 Browser compatibility check when it scanned for IE6. The address is http://www.eastontroop66.org and it's the home page. Thank you!
-
In the attached file, I have a series of symbols that have a drag and drop command to change colour at different sections of a bullseye, and that are also text editable (html).
However, some of the symbols get stuck and will not be moved after moving once or at all, and some get stuck once their text has been edited.
I have poured over the code and it appears to be the same for each symbol - can anyone explain as to why this is happening?
I also cannot now edit the text properly on the ipad (it is really fiddly to change between different symbols to edit their text -- is there maybe a better way to do this? A button to change between symbols to then edit their text, can you help with this too?)
THANK YOU SO MUCH!!!
File here:
https://www.dropbox.com/s/g71gnfichjgyehn/NEW%20RISK%20RADAR.zipHi, I think I undertsand what you mean now, so the code is as below, btu I am not sure what a handler is? but some of my risks still get stuck once the text has been changed on them:
// Use for loop for attr
// deleted yepnope since you load with scropt loading
// added pos for each symbol so we can replace them there.
document.ontouchmove = function(e) {
e.preventDefault();
var risk = ;
var Pos = [
{'x':-9,'y':806},
{'x':27,'y':854},
{'x':72,'y':894},
{'x':71,'y':934},
{'x':231,'y':811},
{'x':231,'y':853},
{'x':231,'y':894},
{'x':231,'y':934},
{'x':388,'y':811},
{'x':388,'y':852},
{'x':388,'y':893},
{'x':388,'y':934},
{'x':543,'y':811},
{'x':543,'y':853},
{'x':543,'y':893},
{'x':543,'y':934}
var myText = ;
for (i=0;i<risk.length;i++){
sym.getSymbol(risk[i]).$(risk[i]).attr("contenteditable",true);
sym.$('Quadrant_text').attr("contenteditable",true);
sym.$('Quadrant1_text').attr("contenteditable",true);
sym.$('Quadrant2_text').attr("contenteditable",true);
sym.$('Quadrant3_text').attr("contenteditable",true);
// apply the draggable JQuery UI plugin to the MyDraggableSymbol symbol on your stage
sym.$('Risk1').draggable(,
drag: function(e,ui)
sym.getSymbol("Risk1").stop("Initial");
sym.setVariable("symName","Risk1");
//adding for risk3_orange similarly add for other symbols
sym.$('Risk1').draggable();
sym.getSymbol('Risk1').$("Risk1").bind('click tap',function(ev) {
sym.$('Risk1').draggable('disable');
}).unbind('dblclick tap',function(ev) {
sym.$('Risk1').draggable('enable');
sym.$('Risk2').draggable(,
drag: function(e,ui)
sym.getSymbol("Risk2").stop("Initial");
sym.setVariable("symName","Risk2");
//adding for Risk2 similarly add for other symbols
sym.$('Risk2').draggable();
sym.getSymbol('Risk2').$("Risk2").bind('click tap',function(ev) {
sym.$('Risk2').draggable('disable');
}).bind('dblclick tap',function(ev) {
sym.$('Risk2').draggable('enable');
sym.$('Risk3').draggable(,
drag: function(e,ui)
sym.getSymbol("Risk3").stop("Initial");
sym.setVariable("symName","Risk3");
//adding for Risk3 similarly add for other symbols
sym.$('Risk3').draggable();
sym.getSymbol('Risk3').$("Risk3").bind('click tap',function(ev) {
sym.$('Risk3').draggable('disable');
}).bind('dblclick tap',function(ev) {
sym.$('Risk3').draggable('enable');
sym.$('Risk4').draggable(,
drag: function(e,ui)
sym.getSymbol("Risk4").stop("Initial");
sym.setVariable("symName","Risk4");
//adding for Risk4 similarly add for other symbols
sym.$('Risk4').draggable();
sym.getSymbol('Risk4').$("Risk4").bind('click tap',function(ev) {
sym.$('Risk4').draggable('disable');
}).bind('dblclick tap',function(ev) {
sym.$('Risk4').draggable('enable');
sym.$('Risk5').draggable(,
drag: function(e,ui)
sym.getSymbol("Risk5").stop("Initial");
sym.setVariable("symName","Risk5");
//adding for Risk5 similarly add for other symbols
sym.$('Risk5').draggable();
sym.getSymbol('Risk5').$("Risk5").bind('click tap',function(ev) {
sym.$('Risk5').draggable('disable');
}).bind('dblclick tap',function(ev) {
sym.$('Risk5').draggable('enable');
sym.$('Risk6').draggable(,
drag: function(e,ui)
sym.getSymbol("Risk6").stop("Initial");
sym.setVariable("symName","Risk6");
//adding for Risk6 similarly add for other symbols
sym.$('Risk6').draggable();
sym.getSymbol('Risk6').$("Risk6").bind('click tap',function(ev) {
sym.$('Risk6').draggable('disable');
}).bind('dblclick tap',function(ev) {
sym.$('Risk6').draggable('enable');
sym.$('Risk7').draggable(,
drag: function(e,ui)
sym.getSymbol("Risk7").stop("Initial");
sym.setVariable("symName","Risk7");
//adding for Risk7 similarly add for other symbols
sym.$('Risk7').draggable();
sym.getSymbol('Risk7').$("Risk7").bind('click tap',function(ev) {
sym.$('Risk7').draggable('disable');
}).bind('dblclick tap',function(ev) {
sym.$('Risk7').draggable('enable');
sym.$('Risk8').draggable(,
drag: function(e,ui)
sym.getSymbol("Risk8").stop("Initial");
sym.setVariable("symName","Risk8");
//adding for Risk8 similarly add for other symbols
sym.$('Risk8').draggable();
sym.getSymbol('Risk8').$("Risk8").bind('click tap',function(ev) {
sym.$('Risk8').draggable('disable');
}).bind('dblclick tap',function(ev) {
sym.$('Risk8').draggable('enable');
sym.$('Risk9').draggable(,
drag: function(e,ui)
sym.getSymbol("Risk9").stop("Initial");
sym.setVariable("symName","Risk9");
//adding for Risk9 similarly add for other symbols
sym.$('Risk9').draggable();
sym.getSymbol('Risk9').$("Risk9").bind('click tap',function(ev) {
sym.$('Risk9').draggable('disable');
}).bind('dblclick tap',function(ev) {
sym.$('Risk9').draggable('enable');
sym.$('Risk10').draggable(,
drag: function(e,ui)
sym.getSymbol("Risk10").stop("Initial");
sym.setVariable("symName","Risk10");
//adding for Risk10 similarly add for other symbols
sym.$('Risk10').draggable();
sym.getSymbol('Risk10').$("Risk10").bind('click tap',function(ev) {
sym.$('Risk10').draggable('disable');
}).bind('dblclick tap',function(ev) {
sym.$('Risk10').draggable('enable');
sym.$('Risk11').draggable(,
drag: function(e,ui)
sym.getSymbol("Risk11").stop("Initial");
sym.setVariable("symName","Risk11");
//adding for Risk11 similarly add for other symbols
sym.$('Risk11').draggable();
sym.getSymbol('Risk11').$("Risk11").bind('click tap',function(ev) {
sym.$('Risk11').draggable('disable');
}).bind('dblclick tap',function(ev) {
sym.$('Risk11').draggable('enable');
sym.$('Risk12').draggable(,
drag: function(e,ui)
sym.getSymbol("Risk12").stop("Initial");
sym.setVariable("symName","Risk12");
//adding for Risk12 similarly add for other symbols
sym.$('Risk12').draggable();
sym.getSymbol('Risk12').$("Risk12").bind('click tap',function(ev) {
sym.$('Risk12').draggable('disable');
}).bind('dblclick tap',function(ev) {
sym.$('Risk12').draggable('enable');
sym.$('Risk13').draggable(,
drag: function(e,ui)
sym.getSymbol("Risk13").stop("Initial");
sym.setVariable("symName","Risk13");
//adding for Risk13 similarly add for other symbols
sym.$('Risk13').draggable();
sym.getSymbol('Risk13').$("Risk13").bind('click tap',function(ev) {
sym.$('Risk13').draggable('disable');
}).bind('dblclick tap',function(ev) {
sym.$('Risk13').draggable('enable');
sym.$('Risk14').draggable(,
drag: function(e,ui)
sym.getSymbol("Risk14").stop("Initial");
sym.setVariable("symName","Risk14");
//adding for Risk14 similarly add for other symbols
sym.$('Risk14').draggable();
sym.getSymbol('Risk14').$("Risk14").bind('click tap',function(ev) {
sym.$('Risk14').draggable('disable');
}).bind('dblclick tap',function(ev) {
sym.$('Risk14').draggable('enable');
sym.$('Risk15').draggable(,
drag: function(e,ui)
sym.getSymbol("Risk15").stop("Initial");
sym.setVariable("symName","Risk15");
//adding for Risk15 similarly add for other symbols
sym.$('Risk15').draggable();
sym.getSymbol('Risk15').$("Risk15").bind('click tap',function(ev) {
sym.$('Risk15').draggable('disable');
}).bind('dblclick tap',function(ev) {
sym.$('Risk15').draggable('enable');
sym.$('Risk16').draggable(,
drag: function(e,ui)
sym.getSymbol("Risk16").stop("Initial");
sym.setVariable("symName","Risk16");
//adding for Risk16 similarly add for other symbols
sym.$('Risk16').draggable();
sym.getSymbol('Risk16').$("Risk16").bind('click tap',function(ev) {
sym.$('Risk16').draggable('disable');
}).bind('dblclick tap',function(ev) {
sym.$('Risk16').draggable('enable');
sym.getSymbol("Drop").$('Outer').droppable(
sym.getSymbol("Drop").$('Middle').droppable(
sym.getSymbol("Drop").$('Target').droppable(
sym.$('resetBtn').click(function(){
sym.$('Quadrant_text').html('Quadrant');
sym.$('Quadrant1_text').html('Quadrant');
sym.$('Quadrant2_text').html('Quadrant');
sym.$('Quadrant3_text').html('Quadrant');
for (i=0;i<risk.length;i++){
sym.$(risk[i]).css({"left":Pos[i].x,"top":Pos[i].y,"position":"absolute"})
sym.getSymbol(risk[i]).stop(0);
sym.getSymbol(risk[i]).$(risk[i]).html("Challenge");
But is still doesn't work,
Subject: Re: Pls Help! Drag and Drop problem, identical symbols acting differently - same code! WHY? -
Has any one found a fix for the iOS 5 WI FI dropping problem?
I own an iPhone 4 and when I upgraded to iOS 5.1.1 it began dropping the WI FI connection randomly, usually after only a few minutes of inactivity. The only solution is to re-start my router and it works fine for a while then drops the connection. I am certain the problem is not with the iPhone hardware. It must be a bug in iOS 5.1.1.
I have been an apple user since the beginning and I have owned just about every model of Mac, I hope Apple will address this issue soon, as I can not imagine any way end users can fix the problem. For the record; my iPhone is factory fresh and not hacked in any way.
Thank you in advance for any assistance...I'm not aware of any wifi drop problem, which leads me to believe that your router is the problem (or your wifi carrier). Have you had problems using wifi at a public location, like a coffee shop or any store that provides free wifi?
Maybe you are looking for
-
In the data acquisition, I use one loop to poll data from hardware, another loop to receive the data from polling loop sent by queue. But everytime the size of the transferred data array may not be the same, so the system may assign different array s
-
Forms are not geeting compiled in R12
Hi All, Forms are not getting compiled... as we are getting the the below error FRM-91500: Unable to start/complete the build... Please advise... Regards, Kumar
-
there is no mail in the app and I have already synced it. what do I do?
-
Hide duplicate row and analytic functions
Hi all, I have to count how many customers have two particular product on the same area. Table cols are: AREA PRODUCT_CODE (PK) CUSTOMER_ID (PK) QTA The query is: select distinct area, count(customer_id) over(PARTITION BY area) from all_products wher
-
Space.bar.is.not.responding.
I.was.using.my.keyboard.and.I.think.I.have.hit.a.key.by.mistake.as.suddenly.my.space.bar.stopped.responding.this.is.the.only.way.I.can.type.anything.please.help