WLAN controller 4400 series, use service-port for initial configuration, IP address?

Hi, Everyone,
I just got a new Cisco Wlan controller 4402 from somebody else but I can't find a suitable console cable( DB-9 console on the controller) , I googled everywhere and I read I could use service port to do the initial configuration, the CISCO FAQ says initial IP for service port is 192.168.1.1, I tried use Cross-over cable to connect a PC to the service port directly and use a normal cable with a switch to connect the service port and a PC, both of the connections do not work out: from the PC, I can't ping 192.168.1.1 ( PC IP changed to 192.168.1.20) , nor can I go http://192.168.1.1 . The service port Link is solid GREEN and ACT is solid GREEN, the PC NIC says Connected with 100 Mbps , so I'm wondering the IP address of service port is not 192.168.1.1? Please help.
Any sussgestions and advices are greatly appreciated.

Hi,
plz connect service port to the switch port that should be configured as access.
connect a pc (ip address - as u mentioned) to the other port of the switch. both wlc and pc should be in same vlan (create a temperary vlan).
try https to access the wlc.
Thanks

Similar Messages

Aironet 3600 series and Controller 4400 series

Hi all,
Can Controller 4400 series work with Aironet 3600 series?

Are there any plans to have a 7.1 or 7.2 version for the 4400 controllers or does it not have enough processor/memory to support the 3600's
The 4400 does not have enough "grunt" (CPU power) and memory to support either the 7.1.X and 7.2.X firmware.
Since the announcement of the end-of-sale for the 4400-family, the only thing Cisco will release for the 4400 for engineering releases. Cisco will no longer be releasing new-feature firmware for this hardware.

Problem WLAN controller 4400

There is a WLAN controller 4400 which controls the access points. There is a collapse of all access points from 00:00 to 00:12.
The link is working properly, no problems with the AC, the point is not restarted.
Logging
1. May 24 2010 00:01:08 CAPWAP 3 ECHO_ERR capwap_ac_sm.c:5116 Did not receive heartbeat reply; AP: 00:3a:98:5e:f7:80 *
2. May 24 2010 00:02:38 CAPWAP 3 ECHO_ERR capwap_ac_sm.c:5116 Did not receive heartbeat reply; AP: 00:26:ca:b7:ce:30 *
3. May 24 2010 00:02:49 DOT1X 3 ABORT_AUTH 1x_bauth_sm.c:447 Authentication aborted for client 00:15:70:f1:e4:b4 *
4. May 24 2010 00:03:07 APF 3 INVALID_RADIO_TYPE apf_api.c:27324 Invalid radio type 255 received. *
5. May 24 2010 00:06:50 APF 3 INVALID_RADIO_TYPE apf_api.c:27324 Invalid radio type 255 received. *
6. May 24 2010 00:06:50 APF 3 INVALID_RADIO_TYPE apf_api.c:27337 Invalid radio type 255 received. *
7. May 24 2010 00:06:50 APF 3 INVALID_RADIO_TYPE apf_api.c:27324 Invalid radio type 255 received. *
8. May 24 2010 00:06:50 APF 3 INVALID_RADIO_TYPE apf_api.c:27337 Invalid radio type 255 received. *
9. May 24 2010 00:07:03 APF 3 INVALID_RADIO_TYPE apf_api.c:27324 Invalid radio type 255 received. *
10. May 24 2010 00:07:03 APF 3 INVALID_RADIO_TYPE apf_api.c:27337 Invalid radio type 255 received. *
11. May 24 2010 00:07:10 APF 3 INVALID_RADIO_TYPE apf_api.c:27324 Invalid radio type 255 received. *
12. May 24 2010 00:07:10 APF 3 INVALID_RADIO_TYPE apf_api.c:27337 Invalid radio type 255 received.

If your WLC firmware is 5.X then I would like to recommend you upgrade to 6.X.

I have a Mac OSX version 10.75 with just one Thunderbolt port. and it has been my Thunderbolt port to connect with Blackmagic wear my intensity. and I no longer can use the port for mini-DVI adapter to connect with me. I do not want to ask any other way f

i have a Mac OSX version 10.75 with just one Thunderbolt port. and it has been my Thunderbolt port to connect with Blackmagic wear my intensity. and I no longer can use the port for mini-DVI adapter to connect with me. I do not want to ask any other way for me to use to use my monitor. I monitor LG FLATRON E2041 brand .. PLEASE Helpp ME

i have a Mac OSX version 10.75 with just one Thunderbolt port. and it has been my Thunderbolt port to connect with Blackmagic wear my intensity. and I no longer can use the port for mini-DVI adapter to connect with me. I do not want to ask any other way for me to use to use my monitor. I monitor LG FLATRON E2041 brand .. PLEASE Helpp ME

Using Appliance Ports for NAS

Using Appliance Ports for NAS
Hey all connecting a NAS to UCS. Would like to plug in directly to FI’s using the Appliance Port option.
Are the steps basically
Turn on Ports use as Appliance Ports
Make PIN Group through Appliance Ports (this will only be one port per FI, I am guess Port-Channels can be used if NAS supports that?)
Make VLAN internal to UCS
Make vNIC Template and use newly created VLAN and PIN Group
Boom!
Right?
Thanks!
Craig

I have made port 20 on each 6120 an Appliance Ports.
Each port is assigned to a VLAN made under the Appliances tab.
Cannot seem to make a PIN group using these Appliance ports. They are not a option.
Is there something I am missing?
Thanks!
Craig

How can i write a vi in using parallel port for digital inputs

Dear all,
i am a beginner user of LabVIEW and i want to write a vi in using parallel port for digital I/O. After reading the article "Using the Parallel Port in LabVIEW
" and download the parallel.zip, i know how to write the vi for output, but i still don't know how to write the input one.i've try to use a Inport.vi to test, but nothing change when i set pin2-9 to high. (my computer:win2K & LabVIEW 6.1)
Can anybody teach me how to write it?
Can anyone write the vi for me too?
Thanks all!
p.s.i've already install the "accessHW.exe"

Are you using VISA or the accessHW VIs? You may need to goto the bios and set the parallel port to run in spp mode or standard mode. This is the simpliest configuration and where you should start.
As far as writing the VI goes, just copy the diagram out of the tutorial you mentioned.

Where can i find the "use audio port for" button?

I am a Dj and am trying to record. All instructions I have seen, it says to plug my mixer into the line-in input and go to system preferences>sound>input, then change the "use audio port for" option to "sound input". I am not able to do find the "use audio port for" drop down menu, any help??? I have a MacBook Pro that is about six months old and I am running OS X 10 9 4.

King_Penguin wrote:
What are hoping to achieve via Bluetooth ? On iOS devices it's mainly for headphones and keyboards, not, for example, for copying content between the devices : supported profiles
I was actually hoping to use my computer as a DHCP. I am in Iraq and have a very hard time getting a solid connection. However my computer has no issues. I am usualy able to use Safari but can not get to iMessage or Facetime servers. I have Windows 7 64bit a bluetooth compatibility. Not looking for any file transfers or special stuff. Just a ICS set up.

HT3625 I have a 2012 macBook Pro 13" and the option "Use audio port for" does not appear at all in the sound menu. why is this? im running mountain Lion 10.8.2

I have a 2012 macBook Pro 13" and the option "Use audio port for" does not appear at all in the sound menu. why is this? im running mountain Lion 10.8.2

Because line-in has been removed.
It does allow for an Apple headset with mic., but I don't know if it would work with third-party ones.
You'll need to use a Griffin iMic or similar to use line-in via a USB port.
The same goes for the 15" retina, the newest MBA and the new iMac (whenever it finally arrives).

Using 40GE ports for VPC Peer Link

Hi,
Is it possible to use the native 40GE ports on the N7K-M206FQ-23L module for the VPC Peer Link, or do you have to break these ports out into 10GE ? I have read that 10GE ports must be used for the VPC peer link.
Thanks in advance.

You can use 40GE ports for VPC peer-link. No need to break those to 10G.

Can time capsule be connected wirelessly and still use ethernet ports for other devices?

can time capsule be connected wirelessly and still use ethernet ports for other devices? we have it connected wirelessly but devices connected to the ethernet ports are not working.

Not as an additional router.. the TC will be plugged into the main router via ethernet (or ethernet equivalent)..
Then the TC is setup in bridge mode. It will simply act as a Switch and HDD.
The wireless can be setup in a number of ways.
From your convenience point of view use it in roaming network mode..
you simply give the TC the same Wireless Name as the existing routers SSID.
Same security setting and password. WPA2 Personal = WPA2 AES which is the best.
But they both use different wireless channels.. normally if you leave the TC on auto it will work fine, but I prefer to control the network.. so set the main router to say 1 and the TC to 11.
You can also use a completely different wireless name etc.. that is up to you. It is still a single flat network and the only thing that is important is only having one router.

I want to use Mac Mail for my work email address, which containts multiple outbound options (i.e. hr@, me@ etc). Is there a way to set up Mac Mail to have an account with multiple outbound addresses rather than adding in multiple accounts?

I want to use Mac Mail for my work email address, which containts multiple outbound options (i.e. hr@, me@ etc). Is there a way to set up Mac Mail to have an account with multiple outbound addresses rather than adding in multiple accounts?

This sounds like the age old problem with keychain & Safari. I don't know of a way to solve it without using something like 1Password.
The iOS app has it's own built in browser, so it has more control over what gets autofilled. Safari on OS X has an 1Password extension that handles account selection & autofill etc.
Keychain is great in principle, but it quickly falls down when you need tight integration with many ID's & different use cases (work, home etc).
I'd suggest you submit feedback to Apple about your thoughts. I did so years ago about this issue & this is how far we have come (back to the point where me.com synced passwords) :^)
http://apple.com/feedback/macosx.html
Other tools like lastpass or keypassx may also help if you want to truly segregate password storage, but that doesn't fix autofill, the way around that issue is to dedicate one browser for work.

Controller access using service port

Hi,
We have two 5508 in ha(ap sso) mode. the service port is configured with 192.168.125.1.
Will i be able to access the controller web interface ( https://192.168.125.1 ) if my laptop is directly connected to the controllers service port(SP) using a ethernet cable.
I was able to do this before, but seems after configuring the HA , it is not accessible any more via service port.
Please help on this.

Might want to look at this thread
https://supportforums.cisco.com/thread/2203573
Sent from Cisco Technical Support iPhone App

Issue on Service Ports for outgoing connection

Hi,
My question is regarding to my desktop Mac making outgoing connection to an external IP address 184.84.124.244 using TCP protocol destination port 443 but using 40 Service Ports between 49170 through 49217. This is an automatic outgoing connection by OS X 10.7.3 (I assumed as I did not make that connection). Why such connection required 40 ports to be opened at the same time? Anyone have any idea what might have caused that? Thanks.

There could be lots of outgoing connections when you fire up Safari, as an example, because by default it has many favourites that are RSS feeder. You could have added some new yourself.
How do I find out if those connections stay up indefinitely?
By the way just curious, how did you look up the IP address as who they are?
If you are "Terminal aware" there are some commands that can help you in this direction
host
host is a simple utility for performing DNS lookups. It is normally used to convert names to IP addresses and vice versa. When no arguments or options are given, host prints a short summary of its command line arguments and options.
netstat
show network status
whois
The whois utility looks up records in the databases maintained by several Network Information Centers (NICs).
nslookup
query Internet name servers interactively
dig
dig (domain information groper) is a flexible tool for interrogating DNS name servers. It performs DNS lookups and displays the answers that are returned from the name server(s) that were queried. Most DNS administrators use dig to troubleshoot DNS problems because of its flexibility, ease of use and clarity of output. Other lookup tools tend to have less functionality than dig.
just to name a few.
netstat in particular let you know which connections and their relative status are going on between your computer and the rest of the world

Services port for web access

I would like to change default port for all web services from port 80 to port 8080 and have full access to webmail, iCal, web page, wiki
How can I do that?

Hello Jay!
Take a look at this doc:
http://www.cisco.com/en/US/docs/solutions/Verticals/mstdcmsftex.html#wp609677
RPC requires source ip sticky in order to operate correctly through a loadbalancer. In the doc, they also walk through doing RPC over http/https - however, I have seen configurations where ACE is not L5-L7 that use RPC on port 135 as a L4 rule with sticky and it appears to work ok.
Regards,
Chris Higgins

Using USB port for dial up networking with mobile phone?

I am thinking of using my mobile phone as a dial up modem when i am away from home and it uses a data cable to the USB port. is there a way to use the USB port on a Mac as your source for the internet?
Thanks
Jason

well i dont have the cable yet i just was wondering if that would work. Yes it has bluetooth but i was told you cant use the bluetooth for a modem. Dont know why the phone has the option. How would i set up that option?

WLAN controller 4400 series, use service-port for initial configuration, IP address?

Similar Messages

Maybe you are looking for