WLAN Controller can configure as ACTIVE-ACTIVE

Customer is looking for two numbers WLAN Controller (AIR-AP1242AG-E-K9). And they want to configure as ACTIVE-ACTIVE. I would like to know whether it can be configuring as ACTIVE-ACTIVE.
And Is really require WLAN Controller for AIR-AP1242AG-E-K9 access point ? or it can be configure without WLAN controller ?
Please revert me ASAP
Regards,
Manoj

Hi Manoj,
Although WLC Controllers can be configured in an Active-Active type redundancy, you don't need the WLC for small deployments. The AIR-AP1242AG-E-K9 access point can be setup in Autonomous or Stand-alone mode as well :)
Cisco IOS Software Configuration Guide for Cisco Aironet Access Points 12.3(7)JA
http://www.cisco.com/en/US/docs/wireless/access_point/12.3_7_JA/configuration/guide/i1237sc.html
Cisco Aironet 1200 Series Access Point Hardware Installation Guide
http://www.cisco.com/en/US/docs/wireless/access_point/1200/installation/guide/1200-TD-Book-Wrapper.html
Hope this helps!
Rob

Similar Messages

Wlan controller, can't bring up the gui, please advise

Hi,
I as configuring WLAN controller, I did following configuration but I still couldn't bring up the GUI and I wasn't able to ping WLAN controller interface ip addresses from other devices and visa versa.
Service Interface IP Address Configuration [none][DHCP]: none
Service Interface IP Address: 10.10.10.1
Service Interface Netmask: 255.255.255.0
Enable Link Aggregation (LAG) [yes][NO]: yes
Management Interface IP Address: 192.168.132.1
Management Interface Netmask: 255.255.255.0
Management Interface Default Router: 192.168.132.2
Management Interface VLAN Identifier (0 = untagged):
Management Interface DHCP Server IP Address: 192.168.132.111
AP Manager Interface IP Address: 192.168.132.4
AP-Manager is on Management subnet, using same values
AP Manager Interface DHCP Server (192.168.132.111):
Virtual Gateway IP Address: 10.42.1.230
Mobility/RF Group Name: NapNac
Network Name (SSID): test
Allow Static IP Addresses [YES][no]: yes
Configure a RADIUS Server now? [YES][no]: no
Warning! The default WLAN security policy requires a RADIUS server.
Please see documentation for more details.
Enter Country Code list (enter 'help' for a list of countries) [US]: US
Enable 802.11b Network [YES][no]: yes
Enable 802.11a Network [YES][no]: yes
Enable 802.11g Network [YES][no]: yes
Enable Auto-RF [YES][no]: yes
Configure a NTP server now? [YES][no]: yes
Enter the NTP server's IP address: 10.50.2.3
Enter a polling interval between 3600 and 604800 secs: 4000
Configuration correct? If yes, system will save it and reset. [yes][NO]: yes
>config network webmode enable
>config network secureweb enable
I did above config. but I still couldn't bring up the GUI.
Please advise how do I resolved this.
Thanks...

Hello
You can give your pc ip address 192.168.132.X and connect directly with the management interface (no lag configured)
Possible problems
->Management interface doesn't tag frames while switch does
Management Interface VLAN Identifier: xxx or put 0 and configure it as native vlan on the switch
--> LAG wrong configured on the switch --> ports down
Check if your etherchannel (LAG) on the switch is up
Still not ok
-> Default-gateway is wrong

WLAN Controller basic configuration help needed

Please advise me for the initial config. of wlan controller. if found following parameters needs to be configured for initial config. of wlan controller.
Enable Link Aggregation (LAG) [yes][NO]:
Management Interface IP Address:
Management Interface Netmask:
Management Interface Default Router:
Management Interface VLAN Identifier (0 = untagged):
Management Interface Port Num [1 to 2]:
Management Interface DHCP Server IP Address:
AP Transport Mode [layer2][LAYER3]:
AP Manager Interface IP Address:
AP-Manager is on Management subnet, using same values
AP Manager Interface DHCP Server (192.168.50.3):
Virtual Gateway IP Address:
Please advise me what these parameters mean. I'm new to wlan controller.
Please advise.
Thanks in advance.

Enable Link Aggregation (LAG) [yes][NO]: Yes
Management Interface IP Address: ex - 192.168.1.2
Management Interface Netmask: Ex- 255.255.255.0
Management Interface Default Router: 192.168.1.1
Management Interface VLAN Identifier (0 = untagged):(Hit enter no need to fill this)
Management Interface Port Num [1 to 2]:1
Management Interface DHCP Server IP Address:
AP Transport Mode [layer2][LAYER3]: LAYER 3
AP Manager Interface IP Address: ex - 192.168.1.3 (same subnet that of Management interface)
AP-Manager is on Management subnet, using same values
AP Manager Interface DHCP Server (192.168.50.3):
Virtual Gateway IP Address:1.1.1.1

Cisco 1010AP Can't find 4402 WLAN controller

Hi folks,
I'm running a 4402 WLAN controller running 5.2 code. I've got some 1010APs that don't associate with the WLC. I'm trying to keep the setup basic. The access points are plugged into the same VLAN as the native vlan for port1 on the controller. I've setup a DHCP server in the manner documented. The WLAN controller is configured as a master server. This is the message that I get in the web interface for WLC:
AP with MAC 00:0b:85:6e:4a:90 (AP 1010 #1) is unknown.
Any clues as to what I'm doing wrong?

Hi Daniel,
You won't like this I'm sure, but this is why the 1010 is not working;
**Note: Controller software release 5.0.148.0 or later is not compatible with Cisco Aironet 1000 series access points.
http://www.cisco.com/en/US/docs/wireless/controller/release/notes/crn52.html
Hope this helps!
Rob

WLAN Controller on remote WAN?????

Hi Guys,
In the event of a WLAN controller, can the APs assosiate to a controller a thousand miles away?
The backup controller would be located in the DC where 100% of traffic is destined anyway so bandwidth is not of major concern.
Thanks

no problem - glad to help
if you read this:-
http://www.cisco.com/en/US/docs/wireless/controller/4.0/configuration/guide/c40hreap.html
it will give you alot of good information - but this is for WLC ver 4.0 - in 4.1/4.2 & 5.0 you get more functionality for H-REAP!

WLAN Controller Compatibility

Hi all,
i want to know if CISCO Wlan Controller can support third party Access Point (SENAO ENgenious EAP3660).
thanks in advance

No, only Cisco AP's are supported.

Can't get mobile device to auto configure the active sync server

Hello
I am trying to get my costumer mobile devices to auto configure the active sync server name so they don't have to type it in. I believe I have everything in place Certificates are fine. I populated the external url on the active sync
object in Exchange.
DNS is set up correct. I ran the Exchange Connectivity Analyzer and it runs perfectly. The only test step if fails on is the first attempt to contact the autodiscover service using just the domain name and that is because we have a
record in DNS so our domain name points to our public web server but all the other tests run fine. At the end, it even displays the xml file contents and shows me the external url of the active sync object.
I get a successful run but it first shows SSL certifiate of our public Web site and then hangs on the server config and then prompts me to enter in the server name and domain. My external url in Exchange looks like this:
https://remote.domain.com/Microsoft-Server-ActiveSync
Any Help??
Eddie

Thank you for replaying but there is already internal A record that points to Exchange server. Firewall, DNS external and internal are setup like this:
Firewall:
Port 443 and 25 points to Internal IP of our Exchange 2013 (only mail server in company).
Port 80 not open.
External DNS records:
autodiscover.mydomain.com à points to our WAN IP
remote.mydomain.com à points to our WAN IP
mydomain.com à points to external online webhosting
Internal DNS records:
autodiscover.mydomain.com à points to ours Exchange 2013 internal IP
Remote.mydomain.com à points to ours Exchange 2013 internal IP
mydomain.com à points to external online webhosting
Test form "ExchangeConnectivityTest.com" is Successful but with warnings.
Warnings are about https://mydomain.com/AutoDiscover/AutoDiscover.XML
because
https://mydomain.com is
pointing to website, which is hosted externally.
Eddie

Can Appletalk be active on two network ports for printing?

Here's the core of my question: Can I keep Appletalk active on my Airport network port (in order to print to a wireless print server on an HP Laserjet 2100M) and simultaneously keep it active on my Ethernet port (in order to print to a Brother HL 2700CN networked through my router)?
Nothing I have read gives me to believe I can have Appletalk active on more than one network port. If that is the case, my second question would be:
I there some other way to print to either printer on the network without having to turn off Appletalk manually on the ports not being used?
Here's the configuration I'm facing
G4 Quicksilver 10.3.9
HP Laserjet 2100M with wireless Belkin DP-311P print server
Brother HL-2700CN wired to Belkin Wireless-G router
I would appreciate any help on this, even if it's the simple response, "No, you can't print to both without manually de/activating Appletalk."

for file sharing between computers running 10.4.x and 10.3.x.
actually, not for that either. 10.4 has dropped support for AppleTalk-only File Sharing to make way for Intel Macs and their protocols. 10.4 does still support AppleTalk printing.
AppleTalk would be required to print to older Apple LaserWriters that do not support LPD/LPR printing. In all but two cases, the printers have no Ethernet port, so a Bridge device or software would be required:
Personal LaserWriter NTR
Personal LaserWriter 320
LaserWriter Select 310
LaserWriter Select 360
LaserWriter 4/600 PS
LaserWriter IIf
LaserWriter IIg (Ethernet)
LaserWriter Pro 600
LaserWriter Pro 630 (Ethernet)
Some third-party wireless Access points do not pass AppleTalk packets at all, and cannot be used to print to that class of older LaserWriters.
In 10.3.9 and previous, AppleTalk may still be used for File Sharing with older Macs.
Q840AV,5500,G3 AIO,G3 B&W,G4/867 Other OS and 9.2, 10.3 and Server - LW IIg, LW 4/600, ATalk ImageWriter LQ

How can I copy a PSK from one WLAN Controller to another

I'm trying to replace a WLAN controller with a new one. One WLAN is configured with WPA-PSK. Nobody seems to know the key that was used.
Anyone know if there is a way to extract the encrypted key out of a controller and put it into the new WLAN Controller?
Thanks in advance.

No can do ...
https://supportforums.cisco.com/discussion/11364566/view-psks-wlans-wlc
However, if any users are on a MAC Book and has iCloud enabled you can see the key under the "keys". If you have a windows 7 box and uses the native supplicant you can expose the key on the supplicant ..

DHCP 2012 - Can you mix Active/Active & Active/Passive?

Scenario:
Main site: x thousand users, 100 subnets. 2 DHCP servers running 2012 HA active/active configuration for load balancing.
x satellite sites, < 100 users, < 5 subnets, single DHCP server running 2012.
Question:
Can I add the satellite site subnets to one of the main site DHCP servers in an active/passive configuration when it is already configured as active/active with the other main site DHCP server?
Thanks.
K.

Hi Kevin,
It is be possible and supported to mix and match as long as you don't already have relationships to other dhcp servers in the satellite subnets (in your case).
More information on the topic and supported scenarios can be found on
http://technet.microsoft.com/en-us/library/dn338986.aspx
MCT | MCSE: Private Cloud/Server, Desktop Infrastructure

WLAN controller 4400 series, use service-port for initial configuration, IP address?

Hi, Everyone,
I just got a new Cisco Wlan controller 4402 from somebody else but I can't find a suitable console cable( DB-9 console on the controller) , I googled everywhere and I read I could use service port to do the initial configuration, the CISCO FAQ says initial IP for service port is 192.168.1.1, I tried use Cross-over cable to connect a PC to the service port directly and use a normal cable with a switch to connect the service port and a PC, both of the connections do not work out: from the PC, I can't ping 192.168.1.1 ( PC IP changed to 192.168.1.20) , nor can I go http://192.168.1.1 . The service port Link is solid GREEN and ACT is solid GREEN, the PC NIC says Connected with 100 Mbps , so I'm wondering the IP address of service port is not 192.168.1.1? Please help.
Any sussgestions and advices are greatly appreciated.

Hi,
plz connect service port to the switch port that should be configured as access.
connect a pc (ip address - as u mentioned) to the other port of the switch. both wlc and pc should be in same vlan (create a temperary vlan).
try https to access the wlc.
Thanks

WLAN Controller configuration help needed

Hi,
I need to configure AP with WLAN controller for guest access. we have 2 vlans. vlan 1 - guess vlan (internet only access) and vlan 2 - all access.
while configuring wlan controller. which vlan should i configure as native vlan? I have radius server which would check health of the user and would direct wlan controller to put in user in vlan 1 or 2 depending on its credentials.
please advise how to implement it. what would be initial steps.

Hi,
I have couple of doubts before going further for solution to implement ?
What model of wlan controller & AP , you are using ?
to configure the Controller , initially you need to configure the interface ( which are virtual ) .
You need to connect controller to your existing LAN set-up may be one of the port of your core switch ............
below are the interface which you need to configure in controller .......
1) Management interface with IP ( which will be used to access your controller from lan ... ) this is ip should be able to ping from the network.
2) AP manager IP ( this is again depend on model ) if it is 5500 , this is not required ..
3) Virtual IP : this is should the IP address which is not at all there in your lan eq.1.1.1.1
4) dynamic interface with IP : this is the interface which will map your vlan to WLAN
once you create the mentioned interfaces , you need to create the wlan and map the above dynamic interface with respective wlan.if required you can configure the DHCP pool as well in controller for Wlan.
let me know , whether this information helped you ........................

Why my iphone's iMessage and Facetime can't be activated?

hi, I just bought an iphone4 from the Mississauga apple store two days ago, the iMessage and Facetime can't be activated, so these things are what I tried: (my SIM card matches with my iphone, have a valid carrier, and I paid my bill and have a valid phone number)
1. I connected my iphone to the wifi, and make sure it works,
2. created an account on apple store, and make sure it has been logged on,
3. logged that e-mail account that I used to creat apple account on to my iphone ---> Mail,
4. go to Settings ---> iMessage, and turned it on, and did whatever it told me to do, then it just saying:"Waiting for activation..." for 2 or 3 hours, and told me that activation failed, and the same thing goes with the Facetime.
I tried with each of them 3 times, none of them are working, so I give up, and asked my friend use to working at the ginues bar in an apple store to help me, so:
He download iTunes onto my PC, connected my iphone to my PC, and logged my apple account onto iTunes, then did the PC and iphone thing which I don't really understand, and redo what I did above, and my iMessage and Facetime still can't work, and use he's iphone to call mine with facetime, use mine to call his with facetime, none of the calls worked.
At the end, we even dialed #*5005*7672# to check the SMS service centre number.
***BTW, I CANNOT even send text messages to my friends, I can only call them.
Is there anything else I can try to make the iMessage and facetime working? Or should I just go to the store and ask for an exchange or refund?
T_T, I just can't believe I can't even send out text messages with the iphone which even the unsmart phones can do.
Help me, plzzzzzz
Kate

Hey Bogdannae,
Thanks for using Apple Support Communities.
You might need to user recovery mode since it is staying at the Apple logo.
If you can't update or restore your iOS device
http://support.apple.com/kb/ht1808
Have a nice day,
Mario

Sort Key .... where we can see the activity in GL, Vendor, Customer mater

Hi gurus,
what is the use Sort key,
where we can see that activity. in GL Accounts, Vendor, customer master sort key where we can see effects. what is the use, how it will sort, where i can see.
Thanks for your reply.
Anil

Dear Anil,
Sort key is the one that fills the "Assignment field" of a line item automatically.
For example, for the GR / IR accounts, we normally give the "Purchase Order" as the sort key. This will make the line items in the GR/IR account to be filled with the Purchase order and the Item number.
The automatic clearing (F.13) works with the assignment field. In case the net of two line items (Dr - Cr) is equal to zero and the assignment field of these two lines are the same, then the system will automatically clear these two lines. Hence "Sort key " fills the assignment field and is very useful in automatic clearing
regards
Venkatesh
Assign points if useful

Interface Manager Material Transaction can not be activated

Hi hussein,
One of the interface managers for INVENTORY module can not be activated.
I tried to activated it using:
Navigation: INVENTORY > Setup >Transactions > Interface Managers > Material Transactions
Goto Tools > Launch Manager > Submit Conc. program "Process Transaction Inferface"
Then after the job is completed, I checked the manager but it is still "inactive" status. :(
Its log says:
+---------------------------------------------------------------------------+
Inventory: Version : 11.5.0 - Development
Copyright (c) 1979, 1999, Oracle Corporation. All rights reserved.
INCTCM module: Process transaction interface
+---------------------------------------------------------------------------+
Current system time is 07-DEC-2009 14:57:19
+---------------------------------------------------------------------------+
+---------------------------------------------------------------------------+
Executing request completion options...
Output is not being printed because:
The print option has been disabled for this report.
+------------- 1) PRINT -------------+
+--------------------------------------+
Finished executing request completion options.
+---------------------------------------------------------------------------+
Concurrent request completed successfully
Current system time is 07-DEC-2009 14:57:21
+---------------------------------------------------------------------------+Please help.....
Thanks a lot
msk

Hi yxes;
Navigation: INVENTORY > Setup >Transactions > Interface Managers > Material Transactions
Goto Tools > Launch Manager > Submit Conc. program "Process Transaction Inferface" Related Cm is Up? If yes please follow below and see its helpful:
The print option has been disabled for this report.
Regard
Helios

WLAN Controller can configure as ACTIVE-ACTIVE

Similar Messages

Maybe you are looking for