WLAN disconnects with iOS 8

Since installation of iOS 8 my WLAN disconnects very often with both my iPad Air and my iPhone 5s. Can anyone give advice what to do?
Thanks, MK

Hi mkummer,
If you are having issues with your WiFi connections on your iPad and iPhone after a recent upgrade to iOS 8, you may find the troubleshooting steps outlined in the following article helpful:
iOS: Troubleshooting Wi-Fi networks and connections
Regards,
- Brenden

Similar Messages

  • IOS 8.1 problem: on iPhone 4s WLAN disconnects

    Updating from iOS 8.0 to iOS 8.1 on my iPhone I get a problem with WLAN: on iPhone 4s WLAN disconnects. do you have any solution?

    L.E.
    Limited "space" for an open letter...

  • After entering the Wlan password I can't use the „connect" button. The button is deactivated. Did somebody have a solution? I have an iPad 3 with IOS 8.0.2.

    After entering the Wlan password I can’t use the „connect“ button. The button is
    deactivated. Did somebody have a solution? I have an iPad 3 with IOS 8.0.2.

    Your iPhone's iOS must be same or newer than the one in backups. In your case it is older so you need to update your iPhone and then recover it with backup.

  • My ipod only connects to the wifi when i am in the room of the router. as soon as i go out of the room into some other room it disconnects and doesn't connect again. unless i go to the room of the router. i have an ipod 4 with ios 6.1.6

    my ipod only connects to the wifi when i am in the room of the router. as soon as i go out of the room into some other room it disconnects and doesn't connect again. unless i go to the room of the router. i have an ipod 4 with ios 6.1.6

    Does the iOS device connect to other networks? If yes that tend to indicate a problem with your network.
    Does the iOS device see the network?
    Any error messages?
    Do other devices now have this problem?
    Did the iPod stay connected before?
    Try the following to rule out a software problem:                
    - Reset the iOS device. Nothing will be lost
    Reset iOS device: Hold down the On/Off button and the Home button at the same time for at
    least ten seconds, until the Apple logo appears.
    - Power off and then back on your router
    .- Reset network settings: Settings>General>Reset>Reset Network Settings
    - iOS: Troubleshooting Wi-Fi networks and connections
    - Wi-Fi: Unable to connect to an 802.11n Wi-Fi network      
    - iOS: Recommended settings for Wi-Fi routers and access points
    - Restore from backup. See:
    iOS: How to back up
    - Restore to factory settings/new iOS device.
    If still problem and it does not connect to any networks make an appointment at the Genius Bar of an Apple store since it appears you have a hardware problem. Could be a loose antenna connectin
    http://www.ifixit.com/Guide/iPod+Touch+4th+Generation+Wi-Fi+Antenna+Replacement/ 3640
    Apple Retail Store - Genius Bar

  • IPhone 4S with iOS 6 can't connect to open Wi-Fi network on HP/H3C WX5004 controller

    After upgrading from iOS 5.1.1 to iOS 6, iPhone 4S devices can no longer connect to an open wi-fi network on our campus.
    We have a controller based WLAN from HP/H3C managed by a WX5004 controller with AP models WA2620-AGN and WA2620E-AGN.
    Symptom: In the Wi-Fi dialog on the iPhone, out open campus network with SSID "CampusUniPassau" is displayed. After tapping this SSID, the iPhone tries to connect for a few seconds and then displays the error message 'Unable to join the network "CampusUniPassau'.
    Our WLAN controller logs the following errors:
    *Sep 21 08:40:46:336 2012 ac1 WMAC/7/ERROR : Invalid Extended Capabilities IE length (4).
    *Sep 21 08:40:46:336 2012 ac1 WMAC/7/ERROR :  Error while processing information elements
    #Sep 21 08:40:46:652 2012 ac1 WMAC/4/Station Association Fail: Station Assoc Fail:1.3.6.1.4.1.2011.10.2.75.3.2.0.4<h3cDot11StationAssocFailTrap> StaMac1:68:A8:6D:87:XX:XX StaMac2:68:A8:6D:87:XX:XX StaMac3:68:A8:6D:87:XX:XX Radioid:2 SSIDName:CampusUniPassau Cause:1 Desc:Unknown Failure APID:210235A42MB102000054
    With iOS 5.1.1, all worked well, so this should be an iOS 6 bug. Are there any workarounds until Apple releases a bug fix?
    Thanks in advance for any advice,
       Christian

    HI,
    i am affected by this problem myself. We are also using the H3C WX5004 with WA2620AGN accesspoints.
    Today I got update from H3C and got a new firmware to download.
    HEre is the description:
    The issue of the extended capabilities should be address in 5.20R2308P07  ftp  link below for the WX5004
    The issue was as described below :
    (1)           R2308P06 does not support Extended Capabilities (IE) which is contained in association request from the IPAD 3 IOS6, as below. This has been fixed by  the R2308P07 code.
    Regards
    Florian

  • WiFi problem with iOS 6 and network login screen

    Here is a detail problem description:
    Equipment: iPad 3 with iOS 6
    Environment: corporate network with a login screen that requires login every 24 hours.
    What happens: The very first time I tried to login into the network everything worked fine. The login screen showed up (as always did with iOS 5) as expected. But, the login screen does NOT come after 24 hours (when re-login is required), unless I will reboot the iPad (using the 2 buttons), or I will reset the network settings (which again does a reboot). Switching on-off the WiFi, or any other remedy does NOT work.
    The problem is not related to the network or the particular iPad or iPhone. All iPads and iPhones with iOS 5.2 or earlier work just fine. Only the ones with iOS 6 have this issue.
    I would appreciate any creative idea to resolve the issue. Thank you.

    Look at iOS Troubleshooting Wi-Fi networks and connections  http://support.apple.com/kb/TS1398
    iPad: Issues connecting to Wi-Fi networks  http://support.apple.com/kb/ts3304
    iOS: Recommended settings for Wi-Fi routers and access points  http://support.apple.com/kb/HT4199
    Additional things to try.
    Try this first. Turn Off your iPad. Then turn Off (disconnect power cord for 30 seconds or longer) the wireless router & then back On. Now boot your iPad. Hopefully it will see the WiFi.
    Go to Settings>Wi-Fi and turn Off. Then while at Settings>Wi-Fi, turn back On and chose a Network.
    Change the channel on your wireless router (Auto or Channel 6 is best). Instructions at http://macintoshhowto.com/advanced/how-to-get-a-good-range-on-your-wireless-netw ork.html
    Another thing to try - Go into your router security settings and change from WEP to WPA with AES.
    How to Quickly Fix iPad 3 Wi-Fi Reception Problems
    http://osxdaily.com/2012/03/21/fix-new-ipad-3-wi-fi-reception-problems/
    If none of the above suggestions work, look at this link.
    iPad Wi-Fi Problems: Comprehensive List of Fixes
    http://appletoolbox.com/2010/04/ipad-wi-fi-problems-comprehensive-list-of-fixes/
    Fix iPad Wifi Connection and Signal Issues  http://www.youtube.com/watch?v=uwWtIG5jUxE
    Fix Slow WiFi Issue https://discussions.apple.com/thread/2398063?start=60&tstart=0
    Unable to Connect After iOS Update - saw this solution on another post.
    https://discussions.apple.com/thread/4010130
    Note - When troubleshooting wifi connection problems, don't hold your iPad by hand. There have been a few reports that holding the iPad by hand, seems to attenuate the wifi signal.
    ~~~~~~~~~~~~~~~
    If any of the above solutions work, please post back what solved your problem. It will help others with the same problem.
     Cheers, Tom

  • CVP 7.0.2 Abnormally disconnected with error code 38

    Hi all,
    We have an issue where when called from outbound, it is not possible to reach a certain number. It doesn't even play the dial tone. isdn debug is as follows :
    Feb 15 17:51:01.830: ISDN Se0/2/0:15 Q931: TX -> RELEASE pd = 8  callref = 0xE97B
    Feb 15 17:51:01.846: ISDN Se0/2/0:15 Q931: RX <- RELEASE_COMP pd = 8  callref = 0x697B
    Feb 15 17:51:05.050: ISDN Se0/2/0:15 Q931: RX <- SETUP pd = 8  callref = 0x697D
            Sending Complete
            Bearer Capability i = 0x8090A3
                    Standard = CCITT
                    Transfer Capability = Speech 
                    Transfer Mode = Circuit
                    Transfer Rate = 64 kbit/s
            Channel ID i = 0xA98385
                    Exclusive, Channel 5
            Progress Ind i = 0x8083 - Origination address is non-ISDN 
            Progress Ind i = 0x8A81 - Call not end-to-end ISDN, may have in-band info 
            Calling Party Number i = 0x0081, '02124783464'
                    Plan:Unknown, Type:Unknown
            Called Party Number i = 0xC1, '2751920'
                    Plan:ISDN, Type:Subscriber(local)
    Feb 15 17:51:05.062: ISDN Se0/2/0:15 Q931: TX -> CALL_PROC pd = 8  callref = 0xE97D
            Channel ID i = 0xA98385
                    Exclusive, Channel 5
    Feb 15 17:51:05.066: %HTTPC-6-REQUEST_FAILED: request URI http://ipphone.fw.garanti.com.tr/ipphone/musteribilgiler?source=TLC&call_data=002124783464-800321200 failed
    Feb 15 17:51:05.066: %IVR-3-APP_ERR: Musteri bilgileri serverdan alinamadi - Hata Kodu: error
    Feb 15 17:51:05.210: %HTTPC-6-REQUEST_FAILED: request URI http://10.231.51.141:8000/cvp/VBServlet?MSG_TYPE=PING&CALL_DNIS=2403519900&CALL_ANI=sip:[email protected]:5060&ERROR_CODE=0&RECOVERY_VXML=flash:recovery.vxml&CLIENT_TYPE=IOS&CALL_ID=DE8929A61000013C1771025A0AE7338D&SIP_CALL_ID=[email protected]&CALL_UUI=&VERSION=7.0.2 failed
    Feb 15 17:51:05.226: %HTTPC-6-REQUEST_FAILED: request URI http://10.231.51.141:8000/cvp/VBServlet?MSG_TYPE=PING&CALL_DNIS=2403519900&CALL_ANI=sip:[email protected]:5060&ERROR_CODE=0&RECOVERY_VXML=flash:recovery.vxml&CLIENT_TYPE=IOS&CALL_ID=DE8929A61000013C1771025A0AE7338D&SIP_CALL_ID=[email protected]&CALL_UUI=&VERSION=7.0.2 failed
    Feb 15 17:51:05.230: %HTTPC-6-REQUEST_FAILED: request URI http://10.231.51.141:8000/cvp/VBServlet?MSG_TYPE=PING&CALL_DNIS=2403519900&CALL_ANI=sip:[email protected]:5060&ERROR_CODE=0&RECOVERY_VXML=flash:recovery.vxml&CLIENT_TYPE=IOS&CALL_ID=DE8929A61000013C1771025A0AE7338D&SIP_CALL_ID=[email protected]&CALL_UUI=&VERSION=7.0.2 failed
    Feb 15 17:51:05.238: %HTTPC-6-REQUEST_FAILED: request URI http://10.231.51.141:8000/cvp/VBServlet?MSG_TYPE=PING&CALL_DNIS=2403519900&CALL_ANI=sip:[email protected]:5060&ERROR_CODE=0&RECOVERY_VXML=flash:recovery.vxml&CLIENT_TYPE=IOS&CALL_ID=DE8929A61000013C1771025A0AE7338D&SIP_CALL_ID=[email protected]&CALL_UUI=&VERSION=7.0.2 failed
    Feb 15 17:51:05.246: %IVR-3-APP_ERR:
    **** CVP HANDOFF.TCL: 57080581.76BE11E2.A32B001B.D5293620 abnormally disconnected with code 38. ****
    Feb 15 17:51:05.258: ISDN Se0/2/0:15 Q931: TX -> CONNECT pd = 8  callref = 0xE97D
    Feb 15 17:51:05.290: ISDN Se0/2/0:15 Q931: RX <- CONNECT_ACK pd = 8  callref = 0x697D
    Feb 15 17:51:05.294: %ISDN-6-CONNECT: Interface Serial0/2/0:4 is now connected to 02124783464 N/A
    Feb 15 17:51:07.274: %IVR-3-APP_ERR:  ani: 002124783464 dnis: 800321200 | ev_setup_done ls_000 | ev_disconnected di_016 |
    Feb 15 17:51:07.298: %ISDN-6-CONNECT: Interface Serial0/2/0:4 is now connected to 02124783464 N/A
    Feb 15 17:51:07.298: %ISDN-6-DISCONNECT: Interface Serial0/2/0:4  disconnected from 02124783464 , call lasted 2 seconds
    Feb 15 17:51:07.302: ISDN Se0/2/0:15 Q931: TX -> DISCONNECT pd = 8  callref = 0xE97D
            Cause i = 0x8090 - Normal call clearing
    Feb 15 17:51:07.362: ISDN Se0/2/0:15 Q931: RX <- RELEASE pd = 8  callref = 0x697D
    Feb 15 17:51:07.366: ISDN Se0/2/0:15 Q931: TX -> RELEASE_COMP pd = 8  callref = 0xE97D
    Feb 15 17:51:08.702: ISDN Se0/2/0:15 Q931: RX <- SETUP pd = 8  callref = 0x697E
            Sending Complete
            Bearer Capability i = 0x8090A3
                    Standard = CCITT
                    Transfer Capability = Speech 
                    Transfer Mode = Circuit
                    Transfer Rate = 64 kbit/s
            Channel ID i = 0xA98391
                    Exclusive, Channel 17
            Calling Party Number i = 0x0083, '05336805920'
                    Plan:Unknown, Type:Unknown
            Called Party Number i = 0xC1, '2751935'
                    Plan:ISDN, Type:Subscriber(local)
    Feb 15 17:51:08.714: ISDN Se0/2/0:15 Q931: TX -> CALL_PROC pd = 8  callref = 0xE97E
            Channel ID i = 0xA98391
                    Exclusive, Channel 17
    Feb 15 17:51:08.718: %HTTPC-6-REQUEST_FAILED: request URI http://ipphone.fw.garanti.com.tr/ipphone/musteribilgiler?source=TLC&call_data=005336805920-800321925 failed
    Feb 15 17:51:08.718: %IVR-3-APP_ERR: Musteri bilgileri serverdan alinamadi - Hata Kodu: error
    Feb 15 17:51:08.798: ISDN Se0/2/0:15 Q931: TX -> ALERTING pd = 8  callref = 0xE97E

    Dear
    Code 38 Indicates that the network is not functioning correctly and that the condition is likely to last
    for an extended period.
    to me the GW is not able to make SIP connection and is likely due to incorrect
    IP Address is seen from the GW.I hope to share the configuration.  
    Thank you
    please rate , if this will help

  • ITunes - syncing over WiFi with iOS 7

    Ever since upgrading two phones to iOS 7, iTunes is spamming the console with constant disconnects:
    [date] server iTunes[pid]: Entered:_AMMuxedDeviceDisconnected, mux-device:id
    [date] server iTunes[pid]: Entered:__thr_AMMuxedDeviceDisconnected, mux-device:id
    etc etc
    This goes on for a while, about every 2 minutes, until iTunes hangs.
    Originally, I'd set up these phones to sync over WiFi. After switching this off – only for the devices on iOS 7 – the above errors stop ocurring. Again, this doesn't happen with iOS 6 devices.
    Running a Mac mini with Mac OS X 10.7.5.
    Any ideas beyond switching off WiFi syncing  – which is really inconvenient...

    Thank you very much!

  • Error 4013. my iphone 4s with ios 7 suddenly colllapsed. It appears the apple and turns on and off, always showing the apple.

    error 4013.
    my iphone 4s with ios 7 suddenly colllapsed. It appears the apple and turns on and off, always showing the apple.
    I try to connect it to itunes but when it tries to install the software again it appears error 4013. i tried changing the usb port anda the connecting cable buit it doesnt work. what shall i do??

    Did you already check these suggestions?
    Check USB connections
    If there’s an issue with the USB port, cable, dock, or hub, or if the device becomes disconnected during restore, try troubleshooting the USB connection, then troubleshooting your security software.
    Common errors: 13, 14, 1600-1629, 1643-1650, 2000-2009, 4000, 4005, 4013, 4014, 4016, “invalid response”, and being prompted to restore again after a restore completes.
    To narrow down the issue, you can also change up your hardware:
    Use another USB cable.
    Plug your cable into a different USB port on your computer.
    Try a different dock connector (or no dock).
    Add (or remove) a USB hub between your device and computer.
    Connect your computer directly to your Internet source, with no routers, hubs, or switches.
    If you see your error after changing your USB connections, continue to the next section to troubleshoot your hardware.
    copied from Resolve specific iTunes update and restore errors

  • Safari upload image from camera with iOS 8.1.2

    Hello,
    I'm having trouble try to upload a picture while using Safari on iphone 4s that does not exist in my photo library yet and trying to create one by taking a picture with my camera.
    it doesn't have a problem selecting an existing photo from my library.
    i have also tried to create a simple form with an only input file button and nothing else to verify that its not some script or anything else that is causing the problem
    Steps to reproduce the problem:
    1. open Safari on iphone 4s with iOS 8.1.2
    2. went to www.baldpixel.com/_upload.php
    3. clicked to select a new picture (i.e. not selecting an existing from library)
    4. once taken the picture and pressed on Use Photo safari reloads the form and prompts the message :  A problem occurred with this page so it was reloaded.
    5. closed Safari and tried to open it again, 1 in 3 times i get the message above and the rest of times page reloads.
    same problem has appeared in iphone 6 with the latest version iOS 8.1.2

    Same exact problem as @ropox only I am using iOS v 8.1, iPhone 6.
    I have reports coming in from other testers - they are experiencing the same issue with their iPhones.
    Scenario:
    We have a simple web form with a file upload. in the past, users were able to take a photo with their iphone and upload it via the form upload (simple FILE input). This worked fine in the past, the only difference is the iPhone iOS upgrade to 8.x
    Interesting Update:
    When I connect my iPhone to my mac via a cable and have error reporting going from the iPhone to the Mac's Safari console - hoping to capture some kind of error in the console to figure this out - it works fine! The upload and everything works as expected. As soon as I disconnect the cable and try it again, no dice. I get the web page reloaded with the error: A problem occurred with this page so it was reloaded.

  • Mac Air Mid 2013 w Yosemite 10.10.1 Handoff not working with iPhone 5s with iOS 8.1.1

    I've got a Macbook Air Mid 2013 with Yosemite 10.10.1 and can't get the 2 devices to stay paired via Bluetooth.
    The 2 devices try to pair and after 2-3 sec's they disconnect.
    Both are on the same wireless network and handoff is toggled on.
    Does anyone have any ideas on how to get this handoff working?

    Have you worked through the knowledge base tips in:Get help using Continuity with iOS 8 and OS X Yosemite - Apple Support

  • IPhoto sync with iOS Devices does not work

    I have an 2007 iMac with OS X 10.9.1, iTunes 11.1.3 and iPhoto 9.5.1.
    I have an iPad 2 with iOS 7.0.4 and iPhone 4 with iOS 7.0.4.
    Around the update to OS X 10.9 I have the problem that I can't sync my iPhoto pictures with my iOS devices anymore.
    Beforehand I had no problem. But I can't tell exactly when this problem pop up the first time. (iOS 7, OSX 10.9, iTunes or iPhoto update???)
    The problem is: I can sync all my content with my iOS devices per iTunes without any problemsbut not the fotos from the iPhoto library.
    If I go to the Foto sync page in iTunes I see all my iPhoto Albums, Events, ... I can select and desect all these items. But if I sync this items I see that in the used memory bar no pictures are shown, the foto count do not show any number and on the iOS device all pictures are removed.
    To fix this problem I have tried some options.
    I have disabled the foto sync in iTunes, close iTunes, close iPhoto, remove the iPod cache from the iPhoto library, recreated the iPhoto database, obened iPhot and iTunes again, connectd the iOS device and try to sync some albums from the iPhoto libray again. But no pictuers are synced.
    I have created a new iPhoto library and added some fotos to the new library, created some albums. Then I tried to sync the iOS device with this library. The first sync wored. :-). But then I disconnected the iOS device and later I connected it again and synced another time and all fotos are gone again.
    The only way I can sync my fotos is to switch to folder sync instead of iPhoto library sync. This work, but this is a very bad option!
    What can I do to fix this problem?

    Open the iPhoto Libraray with the Finder as shown in this screenshot
    and locate the folder titled iPod Photo Cache and move it to the Desktop. 
    Close iPhoto, lanuch and try again.
    OT

  • Need help with IOS commands to see wireless printer

    Seems that I'm not asking the question correctly, or providing the right information.
    The problem:
    I've purchased a wireless printer, (an HP 6500a) and I can not see / ping / use the printer on the wireless network.
    Environment:
    Cisco 891 ISR in standalone. Single office - Home-office environment. Nothing spectacular. WLAN connected and operational to the internet.
    The printer is configured to use a static IP of 10.0.0.3 and reports that it is connected to the AP. However, when I ping FROM the command line at the AP, I DO NOT see the printer. (I did previously, but we lost power last night due to a storm and I'm still trying to reconfigure it...) DHCP is configured on the router to exclude the range 10.0.0.1 through 10.0.0.99
    How do I configure the wireless router to allow any connected client to share files / printers etc? Seems that the Cisco router has this shut off
    by default and I've found nothing in the user manual or by asking for help on here how to reverse this so that I can share printers / files on the LAN.
    Please, I'm not stupid, but I'm only casually familiar with IOS and Cisco's networking terms.
    Thanks in advance,
    -Mike
    =============== Begin Wiresless AP config (running-config) ==============
    Current configuration : 3122 bytes
    version 12.4
    no service pad
    service timestamps debug datetime msec
    service timestamps log datetime msec
    no service password-encryption
    hostname (Remnoved)
    enable secret 5 (Removed)
    no aaa new-model
    dot11 syslog
    dot11 ssid (Removed)
       vlan 1
       authentication open
       authentication key-management wpa
       mbssid guest-mode
       wpa-psk ascii 0 (Removed)
    username (removed)
    username (Removed)
    bridge irb
    interface Dot11Radio0
    no ip address
    no ip route-cache
    encryption vlan 1 mode ciphers tkip
    broadcast-key vlan 1 change 30
    ssid (Removed)
    antenna gain 0
    station-role root
    interface Dot11Radio0.1
    encapsulation dot1Q 1 native
    no ip route-cache
    bridge-group 1
    bridge-group 1 subscriber-loop-control
    bridge-group 1 block-unknown-source
    no bridge-group 1 source-learning
    no bridge-group 1 unicast-flooding
    bridge-group 1 spanning-disabled
    interface Dot11Radio1
    no ip address
    no ip route-cache
    encryption vlan 1 mode ciphers tkip
    broadcast-key vlan 1 change 30
    ssid (Removed)
    antenna gain 0
    dfs band 3 block
    channel dfs
    station-role root
    interface Dot11Radio1.1
    encapsulation dot1Q 1 native
    no ip route-cache
    bridge-group 1
    bridge-group 1 subscriber-loop-control
    bridge-group 1 block-unknown-source
    no bridge-group 1 source-learning
    no bridge-group 1 unicast-flooding
    bridge-group 1 spanning-disabled
    interface GigabitEthernet0
    description the embedded AP GigabitEthernet 0 is an internal interface connecting AP with the host router
    no ip address
    no ip route-cache
    interface GigabitEthernet0.1
    encapsulation dot1Q 1 native
    no ip route-cache
    bridge-group 1
    no bridge-group 1 source-learning
    bridge-group 1 spanning-disabled
    interface BVI1
    ip address dhcp client-id GigabitEthernet0
    no ip route-cache
    ip http server
    no ip http secure-server
    ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
    access-list 110 permit icmp any any echo
    access-list 110 permit icmp any any echo-reply
    access-list 110 permit icmp any any source-quench
    access-list 110 permit icmp any any packet-too-big
    access-list 110 permit icmp any any time-exceeded
    bridge 1 route ip
    banner login ^CC
    % Password change notice.
    Default username/password setup on AP is cisco/cisco with privilege level 15.
    It is strongly suggested that you create a new username with privilege level
    15 using the following command for console security.
    username <myuser> privilege 15 secret 0 <mypassword>
    no username cisco
    Replace <myuser> and <mypassword> with the username and password you want to
    use. After you change your username/password you can turn off this message
    by configuring  "no banner login" and "no banner exec" in privileged mode.
    ^C
    line con 0
    privilege level 15
    login local
    no activation-character
    line vty 0 4
    login local
    cns dhcp
    end

    Wireless clients can get on w/o issue. Nobody can ping anyone else or see them.
    No file sharing, no printer.
    Tried using the web-based config which works for some items, but wont access the advanced config.
    I'm on my way into town, so can't post the router config, but it is posted in my earlier question
    of last week. I can login later if you otherwise need it here.
    Thanks,
    -Mike

  • Updated iPhone 4 with IOS 5.1. It gets stuck at step 8.

    Updated iPhone 4 with IOS 5.1. It gets stuck at when syncing on itunes (PC) "waiting for items to copy" step 8, for hours. I disconnected it and now my phone won't stop downloading on it's own. What am I to do please?.

    i have this same problem on my 3gs, but my bar isnt loaded at all. My itunes was not the latest version when I did the update and im wondering if thats anything to do with it? i dont want to restore it because last time i lost all my album artwork which took me ages to do.

  • IPhone 4s with iOS 8.1: Wireless networks not detected

    My iPhone has ceased to detect any wireless networks. When I am trying to turn WLan off and on again, the settings app is extremely slow or hangs or the phone crashes and reboots.
    I have reset the network settings several times with no improvement. I have mad a soft reset with no improvement. Does anyone have any ideas how this might be solved?
    Thank you!

    I had to do a complete reset of my iPhone 4s for another reason (the new iTunes could not access my Phone...). Afterwards wifi networks could be detected more often, even connection was possible sometimes. However this connection still is very unstable and frequently interrupted when used.
    Just now, the iPhone rebootet while I was making a call... These wifi problems are just the top of an iceberg of problems I am having since I've installed iOS 8
    I sincerely hope the announced 8.1.1 solves them (but I don't really believe my iPhone will ever be what it used to be). I doubt an iPhone is the right purchase for my next phone. There are other manufacturers out there who dont' force their customers to use a malfunctioning release of their operating system. I am talking about signing: It isn't even possible to downgrade and install a working os.
    Apple, I loved you so much because you had beautiful products that work seamlessly. With iOS 8 you broke my heart. My iPhone is now a beautiful and useless brick of electronic garbage. From this day forward, I shall regard you as just another hardware manufacturer selling your products at unreasonable prices. Good luck with that. The question if you are able to uphold quality, innovation and design of your products without Steve Jobs has now certainly been answered.

Maybe you are looking for