Wlan doesn't support monitor mode

Hi everybody,
I'm new in the Arch's world and today I installed Arch on my MacBookAir 4.2 and I installed wifite but when I try to change the wl in "monitor mode" the wl crashes and I must restart the wl.
This is a my pc info with this commands:
uname -a
lspci -nnk | grep -iA2 net
lsusb
iwconfig
rfkill list all
lsmod
Linux Arch-MacOSX 4.0.4-1-ARCH #1 SMP PREEMPT Mon May 18 06:43:19 CEST 2015 x86_64 GNU/Linux
02:00.0 Network controller [0280]: Broadcom Corporation BCM43224 802.11a/b/g/n [14e4:4353] (rev 01)
Subsystem: Apple Inc. AirPort Extreme [106b:00e9]
Kernel driver in use: wl
Bus 002 Device 003: ID 05ac:8404 Apple, Inc. Internal Memory Card Reader
Bus 002 Device 002: ID 0424:2513 Standard Microsystems Corp. 2.0 Hub
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 001 Device 003: ID 05ac:850a Apple, Inc. FaceTime Camera
Bus 001 Device 005: ID 05ac:024d Apple, Inc. Internal Keyboard/Trackpad (MacBook Air) (ISO)
Bus 001 Device 008: ID 05ac:821f Apple, Inc. Built-in Bluetooth 2.0+EDR HCI
Bus 001 Device 004: ID 0a5c:4500 Broadcom Corp. BCM2046B1 USB 2.0 Hub (part of BCM2046 Bluetooth)
Bus 001 Device 002: ID 0424:2513 Standard Microsystems Corp. 2.0 Hub
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
wlp2s0 IEEE 802.11abg ESSID:"cvsg1"
Mode:Managed Frequency:2.452 GHz Access Point: 64:66:B3:2D:FF:BD
Bit Rate=52 Mb/s Tx-Power=200 dBm
Retry short limit:7 RTS thr:off Fragment thr:off
Power Management:off
Link Quality=33/70 Signal level=-77 dBm
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0
Module Size Used by
nls_utf8 16384 0
ntfs 204800 0
ppp_deflate 16384 0
bsd_comp 16384 0
ppp_async 20480 1
crc_ccitt 16384 1 ppp_async
l2tp_ppp 24576 0
l2tp_netlink 20480 1 l2tp_ppp
l2tp_core 32768 2 l2tp_ppp,l2tp_netlink
ip6_udp_tunnel 16384 1 l2tp_core
udp_tunnel 16384 1 l2tp_core
pppoe 20480 0
pppox 16384 2 l2tp_ppp,pppoe
ppp_generic 32768 10 l2tp_ppp,pppoe,pppox,bsd_comp,ppp_async,ppp_deflate
slhc 20480 1 ppp_generic
btusb 40960 0
bluetooth 442368 2 btusb
hid_generic 16384 0
wl 6303744 0
coretemp 16384 0
intel_rapl 20480 0
hid_apple 16384 0
iosf_mbi 16384 1 intel_rapl
x86_pkg_temp_thermal 16384 0
intel_powerclamp 20480 0
joydev 20480 0
kvm_intel 155648 0
mousedev 20480 0
kvm 446464 1 kvm_intel
crct10dif_pclmul 16384 0
nls_iso8859_1 16384 1
crc32_pclmul 16384 0
nls_cp437 20480 1
crc32c_intel 24576 0
i915 1024000 8
vfat 24576 1
fat 65536 1 vfat
ghash_clmulni_intel 16384 0
uvcvideo 86016 0
usbhid 49152 0
snd_hda_codec_hdmi 53248 1
hid 110592 3 hid_generic,usbhid,hid_apple
bcm5974 20480 0
applesmc 20480 0
mac_hid 16384 0
iTCO_wdt 16384 0
evdev 24576 13
snd_hda_codec_cirrus 20480 1
iTCO_vendor_support 16384 1 iTCO_wdt
videobuf2_vmalloc 16384 1 uvcvideo
led_class 16384 1 applesmc
aesni_intel 172032 0
snd_hda_codec_generic 65536 1 snd_hda_codec_cirrus
drm_kms_helper 102400 1 i915
input_polldev 16384 1 applesmc
cfg80211 483328 1 wl
aes_x86_64 20480 1 aesni_intel
hwmon 16384 2 applesmc,coretemp
videobuf2_memops 16384 1 videobuf2_vmalloc
lrw 16384 1 aesni_intel
gf128mul 16384 1 lrw
glue_helper 16384 1 aesni_intel
ablk_helper 16384 1 aesni_intel
cryptd 20480 3 ghash_clmulni_intel,aesni_intel,ablk_helper
videobuf2_core 40960 1 uvcvideo
pcspkr 16384 0
snd_hda_intel 28672 3
v4l2_common 16384 1 videobuf2_core
i2c_i801 20480 0
snd_hda_controller 28672 1 snd_hda_intel
snd_hda_codec 114688 5 snd_hda_codec_hdmi,snd_hda_codec_generic,snd_hda_intel,snd_hda_controller,snd_hda_codec_cirrus
videodev 135168 3 uvcvideo,v4l2_common,videobuf2_core
uas 24576 0
media 20480 2 uvcvideo,videodev
sbs 16384 0
snd_hwdep 16384 1 snd_hda_codec
usb_storage 61440 1 uas
rfkill 24576 3 cfg80211,bluetooth
drm 282624 10 i915,drm_kms_helper
sbshc 16384 1 sbs
apple_bl 16384 0
ac 16384 0
snd_pcm 90112 4 snd_hda_codec_hdmi,snd_hda_codec,snd_hda_intel,snd_hda_controller
video 24576 1 i915
battery 20480 0
snd_timer 28672 1 snd_pcm
mei_me 20480 0
button 16384 1 i915
shpchp 36864 0
mei 77824 1 mei_me
intel_gtt 20480 1 i915
snd 69632 14 snd_hwdep,snd_timer,snd_hda_codec_hdmi,snd_pcm,snd_hda_codec_generic,snd_hda_codec,snd_hda_intel,snd_hda_codec_cirrus
i2c_algo_bit 16384 1 i915
lpc_ich 24576 0
i2c_core 53248 7 drm,i915,i2c_i801,drm_kms_helper,i2c_algo_bit,v4l2_common,videodev
soundcore 16384 2 snd,snd_hda_codec
processor 28672 0
sch_fq_codel 20480 3
ext4 512000 3
crc16 16384 2 ext4,bluetooth
mbcache 20480 1 ext4
jbd2 90112 1 ext4
sd_mod 36864 5
ahci 36864 4
libahci 28672 1 ahci
libata 184320 2 ahci,libahci
scsi_mod 147456 4 uas,usb_storage,libata,sd_mod
uhci_hcd 45056 0
ehci_pci 16384 0
ehci_hcd 73728 1 ehci_pci
usbcore 200704 9 uas,btusb,uhci_hcd,uvcvideo,usb_storage,ehci_hcd,ehci_pci,usbhid,bcm5974
usb_common 16384 1 usbcore
0: phy0: Wireless LAN
Soft blocked: no
Hard blocked: no
1: hci0: Bluetooth
Soft blocked: no
Hard blocked: no
How I can use the monitor mode for use wifite?
Thanks for any answer!!!
Last edited by skioda86 (2015-05-22 10:00:45)

As far as i know the wl (proprietary broadcom driver) doesn't support monitor/injection.
But the Mac80211 alternatives might. If they support the wifi chip in your MacBook.
From experience with a friends MBP it didn't yet support his broadcom so had to use WL to get basic network connectivity and used an Dual-band(2.4Ghz/5Ghz) 2x2 11n/ac USB dongle for his monitor/injection needs.

Similar Messages

I recently brought a HD PVR, i put in the disk to install the hard drive and it said " This program doesn't support DOS Mode! how do i get out of DOS Mode?? Please Help

I recently brought a HD PVR, i put in the disk to install the hard drive and it said " This program doesn't support DOS Mode! how do i get out of DOS Mode?? Please Help

What exactly are you trying to do? PVRs are for recording from TV not computers.
Either way, if it's complaining about DOS mode, it's Windows oriented software and not Mac compatible.

MS-DOS.This system doesn't support fullscreen mode in windows server 2008

MS-DOS.This system doesn't support fullscreen mode.Choose close to terminate the application. Unable to open full size screen mode for MS-DOS in virtual windows server 2008

Please anybody could suggest why the MS-DOS does not open full size mode in Windows server 2008. PC cate shell for windows application Is running and alerting this error msg. This system doesn't support fullscreen mode. Choose close to terminate the application.
Please can any body help on this regard.

Solaris 8 looks doesn't support APIC for multi-PCI BUS system

I am Phoenxi BIOS Egnieer
We are testing with Brkdale System(ICH2)
This chipset use PCI0/PCI1/PCI2 for PCI device
With APIC enabled Solaris OS doesn't get the _PRT method on ASL PCI1/2
So PCI slot Network Card Doesn't work on APIC envinment
How Solaris supprt ACPI/APIC envernment
Solaris copy and modify the intel ACPI CA ?
Doesn any issue internally?
Thnanks

As far as i know the wl (proprietary broadcom driver) doesn't support monitor/injection.
But the Mac80211 alternatives might. If they support the wifi chip in your MacBook.
From experience with a friends MBP it didn't yet support his broadcom so had to use WL to get basic network connectivity and used an Dual-band(2.4Ghz/5Ghz) 2x2 11n/ac USB dongle for his monitor/injection needs.

Mode Switcher doesn't support my sound devi

I was unable to switch the modes before, I found the application in the program files, but it tells me that my device is not supported. Any thoughts as to what might cause this?

I just searched for this and saw that X-Fi XtremeAudio doesn't have different modes? That's kind of odd seeing as I have the application for it and the help box tells me I can.

Iwlist scanning gives: Interface doesn't support sc [solved]

When I'm trying to scan for all available networks I get:
# iwlist eth1 scanning
eth1 Interface doesn't support scanning : Operation not supported
My wireless card works fine if I set every parameter manually. I'm currently using the orinoco drivers that came along with ArchLinux.
It seems like that the version of the orinoco drivers installed doesn't support the scan stuff. But building the new orinoco drivers failed with
/usr/local/download/orinoco/orinoco-0.15rc2/orinoco_pci.c: In function `orinoco_ pci_suspend':
/usr/local/download/orinoco/orinoco-0.15rc2/orinoco_pci.c:330: error: too many a rguments to function `pci_save_state'
/usr/local/download/orinoco/orinoco-0.15rc2/orinoco_pci.c: In function `orinoco_ pci_resume':
/usr/local/download/orinoco/orinoco-0.15rc2/orinoco_pci.c:347: error: too many a rguments to function `pci_restore_state'
make[2]: *** [/usr/local/download/orinoco/orinoco-0.15rc2/orinoco_pci.o] Error 1
make[1]: *** [_module_/usr/local/download/orinoco/orinoco-0.15rc2] Error 2
make[1]: Leaving directory `/usr/src/linux-2.6.11.3-ARCH'
make: *** [modules] Error 2
So I did try the wlan-ng26 driver downloaded and installed with pacman.
I remove the orinoco modules with
[root@ArchThinkpad orjanp]# modprobe -r orinoco_pci
But when I try to insert the prism2_pci module, it doesn't exist. Why?
[root@ArchThinkpad orjanp]# modprobe prism2_pci
FATAL: Module prism2_pci not found.
Any heads up on what to do?
This is iwconfig before removing the orinoco modules.
[root@ArchThinkpad orjanp]# iwconfig
lo no wireless extensions.
sit0 no wireless extensions.
eth0 no wireless extensions.
eth1 IEEE 802.11-DS ESSID:"" Nickname:"Prism I"
Mode:Managed Access Point: 00:00:00:00:00:00 Bit Rate:11 Mb/s
Tx-Power=15 dBm Sensitivity:1/3
Retry min limit:8 RTS thr:off Fragment thr:off
Encryption key:off
Power Management:off
Link Quality=0/92 Signal level=-68 dBm Noise level=-122 dBm
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0
This is lspci
[root@ArchThinkpad orjanp]# lspci
00:00.0 Host bridge: Intel Corp. 82845 845 (Brookdale) Chipset Host Bridge (rev 04)
00:01.0 PCI bridge: Intel Corp. 82845 845 (Brookdale) Chipset AGP Bridge (rev 04)
00:1d.0 USB Controller: Intel Corp. 82801CA/CAM USB (Hub #1) (rev 02)
00:1d.1 USB Controller: Intel Corp. 82801CA/CAM USB (Hub #2) (rev 02)
00:1d.2 USB Controller: Intel Corp. 82801CA/CAM USB (Hub #3) (rev 02)
00:1e.0 PCI bridge: Intel Corp. 82801BAM/CAM PCI Bridge (rev 42)
00:1f.0 ISA bridge: Intel Corp. 82801CAM ISA Bridge (LPC) (rev 02)
00:1f.1 IDE interface: Intel Corp. 82801CAM IDE U100 (rev 02)
00:1f.3 SMBus: Intel Corp. 82801CA/CAM SMBus (rev 02)
00:1f.5 Multimedia audio controller: Intel Corp. 82801CA/CAM AC'97 Audio (rev 02)
00:1f.6 Modem: Intel Corp. 82801CA/CAM AC'97 Modem (rev 02)
01:00.0 VGA compatible controller: ATI Technologies Inc Radeon Mobility M7 LW [Radeon Mobility 7500]
02:00.0 CardBus bridge: Texas Instruments PCI1250 PC card Cardbus Controller (rev 01)
02:00.1 CardBus bridge: Texas Instruments PCI1250 PC card Cardbus Controller (rev 01)
02:02.0 Network controller: Harris Semiconductor Prism 2.5 Wavelan chipset (rev 01)
02:08.0 Ethernet controller: Intel Corp. 82801CAM (ICH3) PRO/100 VE (LOM) Ethernet Controller (rev 42)
This is lsmod before removing orinoco.
[root@ArchThinkpad orjanp]# lsmod
Module Size Used by
radeon 78336 1
ohci_hcd 23048 0
ehci_hcd 36488 0
irtty_sir 7552 0
sir_dev 18636 1 irtty_sir
irda 144184 1 sir_dev
crc_ccitt 2432 1 irda
parport_pc 29252 0
parport 38600 1 parport_pc
rtc 13260 0
pcspkr 4044 0
eepro100 32528 0
orinoco_pci 7552 0
orinoco 44172 1 orinoco_pci
hermes 9472 2 orinoco_pci,orinoco
yenta_socket 23560 0
rsrc_nonstatic 11648 1 yenta_socket
pcmcia_core 51488 2 yenta_socket,rsrc_nonstatic
snd_intel8x0m 19396 0
snd_intel8x0 34624 0
snd_ac97_codec 79224 2 snd_intel8x0m,snd_intel8x0
snd_pcm_oss 56224 0
snd_mixer_oss 21120 1 snd_pcm_oss
snd_pcm 98564 4 snd_intel8x0m,snd_intel8x0,snd_ac97_codec,snd_pcm_oss
snd_timer 27268 1 snd_pcm
snd 59492 7 snd_intel8x0m,snd_intel8x0,snd_ac97_codec,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_timer
soundcore 10848 1 snd
snd_page_alloc 10244 3 snd_intel8x0m,snd_intel8x0,snd_pcm
i2c_i801 8972 0
i2c_core 23296 1 i2c_i801
usbhid 47744 0
uhci_hcd 33424 0
usbcore 125560 5 ohci_hcd,ehci_hcd,usbhid,uhci_hcd
shpchp 100996 0
pci_hotplug 34760 1 shpchp
tsdev 8256 0
joydev 10560 0
evdev 9984 0
cpufreq_powersave 2176 0
cpufreq_userspace 5680 0
p4_clockmod 6164 0
speedstep_lib 4868 1 p4_clockmod
freq_table 5008 1 p4_clockmod
e100 37760 0
mii 5760 2 eepro100,e100
nls_cp437 6144 1
vfat 14976 1
fat 41884 1 vfat

orjanp wrote:
Thanks.
I installed the 0.15RC1 version of the Orinoco drivers found here.
I rebooted but I still had the 0.13 version. I did a make and make install as the readme file said.
What do I have to do to update the driver?
do you use a PKGBUILD?
update the driver: if it was copied to the right place and the kernel knows about it (depmod -a) it should work
for a start, check under
ls -la /lib/modules/`uname -r`/kernel/drivers/net/wireless/
that your module is installed under the correct location (the orinoco files should be newer than the other ones)
if this is so, make sure you are depmod -a (as root) ... and if even this is ok, then either you are running the new modules or something strange happened

When does an AP gets to Air-Monitor mode?

Q: When does an AP gets to Air-Monitor mode?
A: In a Mobility-controller AP deployment there are just 3 conditions that an AP can go into an Air-Monitor(AM) Mode:
1. If the am-mode is configured in the "rf dot11a-radio-profile" or "rf dot11g-radio-profile"
To see if it is configured in the radio profile please use this filter in the show running-config command
Example:
(Aruba) #show running-config | begin "rf dot11a-radio-profile"
Building Configuration...
rf dot11a-radio-profile "default"
mode am-mode ------------------------------------------------------------- Indicates that the Airmonitor is Enabled
2. If Mode Aware ARM is turned on in the ARM profile then th ap turns to AM mode when it sees excess power from the neighbor AP
To see if mode aware arm is enabled in the arm profile please use this filter in the show running-config command
(Aruba) #show running-config | begin "rf arm-profile"
Building Configuration...
rf arm-profile "default"
mode-aware ------------------------------------------------- Indicates that the mode aware arm is enabled
3. During the Regulatory mismatch or un-supported
a. When there is no channel available for the AP’s operation for the country defined on the controller.
Use the following command to verify the allowed channels for an AP
(Aruba-7240) #show ap allowed-channels ap-name <name-of-ap>
b. When AP’s has a different country with the controller’s Country.
Compare the country defined on the controller "(Aruba) #show country" to the country defined in the "(Aruba) #show ap regulatory-domain-profile <profile-name>". The ap regulatory-domain-profile will be mapped in the ap-group to which the ap is provisioned to.

Hi Marc,
I have a shop system comprised of two web applications where one is for
maintaining the shop and the other for using the shop. When I do changes
to the shop from the one webapp they do not show up in the second, unless
I call refresh. Also, I have to switch off the cache, it seems and do a
flush on the changed objects. There are some questions now:
a) when I call refresh, is the complete state reread regardless whether
there have been changes or not or does it know, when the state has not
changed in the DB ? it is a performance question, I guess.
b) can I use transactional reads to do the refresh automatically ?
c) I noticed that refresh does not do a deep refresh of all the objects
referenced by the one to be refreshed. Is there a way to do this or do I
have to go thru all the objects ?
I asked some questions some time ago in another thread, which might refer
to. I am sorry, if I am not clear enough.
Best regards
Wolfgang
Marc Prud'hommeaux wrote:
Wolfgang-
I take the question to mean that you are wondering how you can refresh
the state of a persistent instance to reflect changes in the data store.
If that is the case, then you can just call
PersistenceManager.refresh(ob) on the object, and the newer values will
be obtained.
If that doesn't help, can you clarify the question a little?
In article <cj7ris$mhr$[email protected]>, Wolfgang Kundrus wrote:
Do I have to use transactional reads for an object to get the changes done
by another web application ?
Thanks
Wolfgang
Marc Prud'hommeaux
SolarMetric Inc.

Mac mini on a LCD TV which does not support interlace mode

Dear all,
I am going to buy a new Mac mini and I wish to connect it to a Samsung LCD TV 37A656A1F (serie 6.
The TV manual says that it does not support the interlace mode. I then deduce that it supports progressive mode only.
My question: Does it mean that this LCD TV model cannot be used as a monitor for a Mac mini?
Please give a help to me

All computer monitors are progressive mode displays. Therefore all computers, including the mini, are very comfortable running progressive mode. It is their natural state. It is more a problem when a computer has to run interlace mode in order to support a display. That is when there is trouble. So I think you have nothing to worry about if your Samsung runs in progressive mode.

How to enable a dual monitor mode

I have a MSI FX52000 VTD-128 board which suppose to support a dual monitor mode. It has D-Sub analog, DVI and VIVO connectors.
Would it be possible to connest primary monitor to DVI and secondary to analog output or only Video Out can be used for the secondary monitor?

Have you installed the latest "Forceware" Drivers?...I think MSI's 52.70's are great...How you should go about setting up for two displays is to go into NVIDIA Driver Control Panel>trouble shooting>Click on the "Detect Displays" Button after you connect the other monitor ...Sean REILLY875

System freezes when enabling monitor mode for AR9285 on 2.6.36

EDIT: OK, sorry guys, found some more infos on the topic:
https://bbs.archlinux.org/viewtopic.php?pid=863772
Bug report:
https://bugs.archlinux.org/task/21683
I am going to downgrade my kernel to 2.6.35.
Hey all,
I have a severe system failure when trying to set my wlan chipset into monitor mode - works with backtrack 4, which still uses 2.6.30 I guess
reproduce with:
Atheros AR9285 chipset on ArchLinux w/ Kernel 2.6.36 , drivers are standard ath9k which come with Arch Linux
airmon-ng start wlan0 <channel>
"panic occured, switching to console mode.." or something, after a long output, which doesnt get logged, supposedly..
might be related to:
https://bbs.archlinux.org/viewtopic.php?id=104231
although ifconfig wlan0 up works without any problems..
what can I do? downgrading my kernel to 2.6.30, or installing other drivers?
I have to admit I'm not a power user when it comes to kernel and drivers stuff.. but willing to learn.
Thank you
Last edited by domcobb (2010-12-25 22:24:20)

I can't help you, but I had a problem with kernel 2.6.36.1-3, too. I got a kernel panic, when I tried to boot. Only thing I could do was to revert to kernel 2.6.35.x. That happened on my big pc, not on my netbook. Maybe he didn't like my amd cpu, who knows.

Windows 7 Authentication Failures in Monitor Mode on ISE 1.2

Hi Support,
I have a configuration whereby most of my Windows endpoints are not running DOT1x yet. We eventually intend to authenticate them via AD and looking to push out the Windows DOT1x client to all live users soon. Currently users are getting network access due to the fact that all ports have "authentication open" set and the default Authz policy is set to Permit Access (we arent using MAC address endpoint tables to allow MAB etc)
I now have my first test group of users using DOT1x and they match a specific AuthZ policy I have added that checks for their specific AD group on the AD. All is fine.
However I have just added DOT1x to a second test group of users who currently do NOT have any specific matching AuthZ policy (they are on the same AD server but in a diffferent group which I have not defined a policy for yet), and I was expecting they would still join using the default Authz policy. However they do not and on closer observation using "ipconfig" their adapter displays "Media Unauthenticated". I researched this and found that the Windows endpoint can set this condition if you disable the "Fallback to Unauthorized Network" check-box in their dot1x settings. Now I could easily check this box but don't understand why I need to as I surely should be hitting the Default AuthZ policy. However when I debug the switch port I am getting the following:
%DOT1X-5-FAIL: Authentication failed for client (xxxxxxxxxxx) on Interface Gi2/0/26 AuditSessionID 0A540201000064AD8FC27A96
This appears to suggest my AuthC is failing (rather than AuthZ or is the word Authentication a bit vague here?), so here is my question:
1. My AuthC DOT1X policy looks at the Identity Source Sequence that includes the AD server that contains specific groups for BOTH my first test group and my second test group. Users from my first and second test group seem to be hitting this AuthC rule according to ISE.
2. My AuthZ policy contain a specific policy for my first test group ONLY, but the final Default Rule is set to Permit Access. From the ISE persepctive ALL users in my second test group are actually successfully getting this policy. The Authentication Troubleshooting page shows them getting the DOT1X AuthC policy and the Default Rule AuthZ policy. However the message in the switch debug suggests a failure and with my Windows DOT1x client settings as above, the adapter is therefore effecitvely disabled.
3. All this is occuring in Monitor mode, which I thought was harmless provided I dont give additional attributes (VLAN, ACL) to the profiles!
Very confused!
All help welcome
Mark

Please provide us with your Event Viewer administrative logs by following these steps:
Click Start Menu
Type eventvwr into Search programs and files (do not hit enter)
Right click eventvwr.exe and click Run as administrator
Expand Custom Views
Click Administrative Events
Right click Administrative Events
Save all Events in Custom View As...
Save them in a folder where you will remember which folder and save as Errors.evtx
Go to where you saved Errors.evtx
Right click Errors.evtx -> send to -> compressed (zipped) folder
Upload the .zip file to skydrive or a file sharing service and put a link to it in your next post
Wanikiya and Dyami--Team Zigzag

Does the Intel 82579LM NIC on the Portege R830 support Promiscuous mode?

Hi,
I've got a work laptop (Portege R830), which doesn't want to sniff packets. I've got it connected to a Netgear Hub (DS104), along with an older notebook, and then uplink to ADSL.
Running a continuous ping to the default gateway and Wireshark on both devices and the other computer can see the pings from the Toshiba, but not vice-versa.
The Toshiba is running as an Administrator account, has the Windows Firewall disabled, and my Symantec End Point Encryption disabled. I don't have any other AV to my knowledge.
Does anyone have any ideas of services I should disable/enable, or knowledge of the features of this NIC?
According to the Intel site "Yes, all currently marketed Intel PRO/100, Intel PRO/1000, Intel Gigabit, Intel PRO/10 Gigabit, and Intel 10 Gigabit adapters support Promiscuous mode. " But the Intel 82579 Gigabit Ethernet Controller is not in the list that follows on; http://www.intel.com/support/network/sb/CS-004185.htm?wapkw=%28promiscuous%29
Thanks for your time.

Usually the firewall or Internet Security software blocks pings so perhaps try uninstalling Symantec completely. Just disabling it may not disable everything.
Another thing to try is use a Static IP Address instead of DHCP. Disabling IPv6 or installing a newer LAN driver from the Intel website may also help.

Internet plug in that Safari doesn't support

Ouestion. Brand new Mac OSX 10.4 Not able to open Internet programmes,
keep getting Safari doesn't support. Have tried ticking the Rossett box in Safari
with no results. I had no trouble with G4 laptop with Panther. Would appreciate some help , thanks sarsfield

Hi,
You need to install additional plug-ins for Safari to work with RealPlayer or Windows Media video streams.
Flip4Mac (for Windows Media playback)
Real Player (free download link in the top right hand corner)
Note that Flip4Mac is not yet a Universal Binary so you will need to continue running Safari in Rosetta mode for that to work correctly.
If you're still having problems after installing those, please post the website in question so we can take a closer look.
Good luck!

KDL-42W807B doesn't support conversion from 2D to 3D

Hi, i just bought TV model No KDL-42W807B and it doesn't support conversion from 2D to 3D and i need to play my ps4 games in 3D mode so is there is any thing can i do to let my tv convert 2d to 3d or what type of suitable converter to do this job for my ps4

Hi mohands,
The TV model you have provided appears to be not a US model and we are unable to check its specification.
For further assistance regarding your concern, please contact the Sony offices/Sony representative offices nearest to your place of residence in Asia Pacific region http://www.sony-asia.com/countryselector.html?hpid=countryselector:AsiaPacific. Due to proximity, they are in a better position to respond to your questions or concerns.
Thanks,
Jerome
If my post answers your question, please mark it as "Accept as Solution"

Firefox says my operating system doesn't support upgrade. I have MAC OS X 10.5.6

When I tried to download the latest Firefox version, a message said that my operating system doesn't support the upgrade. But the information on download page says MAC OS X 10.5 or better is okay. My system is MAC OS X 10.5.6

Do you have a Intel processor or a PowerPC processor as your user agent suggests and Mach-O would indicate an even older OS X version than 10.5 (possibly OS X 9).
*Mozilla/5.0 (Macintosh; U; PPC Mac OS X Mach-O; en-US; rv:1.8.1.3) Gecko/20070309 Firefox/2.0.0.3
Are running Firefox in some compatibility mode via Rosette?
See:
*https://support.mozilla.com/kb/Websites+or+add-ons+incorrectly+report+incompatible+browser
*http://kb.mozillazine.org/Resetting_your_useragent_string_to_its_compiled-in_default
*Firefox 4 versions and later do not run on a PowerPC Mac.
*Firefox 4 and later require at least OS X 10.5 and an Intel Mac.
* http://www.mozilla.com/firefox/6.0/system-requirements/

Wlan doesn't support monitor mode

Similar Messages

Maybe you are looking for