WLAN & multiple SSIDs
Hello,
I have some problems connecting my iPod touch to my WLAN at work. There are 3 different ssids on one access point. I can connect to each one of them and I get an ip address of the right network. But when I try to go online with the safari or any other webapp nothing happens Any ideas how to solve this problem?
see if this helps then
http://www.everythingicafe.com/forum/wifi/cant-connect-to-wifi-please-help-16221 .html
Similar Messages
-
Single access point with multiple ssids and single channel possible?
Hi everybody.
I have this silly question.
Let say we have three vlans, vlan1,2,3 and they are mapped to wlans as follows:
Vlan 1 ssid1
Vlan 2 ssid2
Vlan3 ssid 3
AP --------trunk------Switchted network.
Our Ap has mobile devices in three wlans, i.e ssid1ssid2 and ssid3
Since AP uses half duplex mode, mobile devices need positive ack from ap before they can send data, therefore once channel let say channel 3( assuming 802.11b is used) can be shared by all mobile devices in three wlans.
Is my understanding correct?
Thanks and have a great weekend.Hii ,
Yes ,that is pretty much possible as suggested by other experts on board. Depending on your access point you will have 1 (2.4 GHz) or both 2.4 & 5GHz radios.
You can configure multiple SSIDs (up to 16 ) known as MBSSID mode in autonomous environment. In Controller based architecture you can configure up to 512 WLAN (SSID) and transmit any 16 of them per AP (using AP group feature). However , it is recommended to keep multiple SSID count below 8 as for each SSID separate beacon will be sent on air which consumes more air time.
Hope this helps
Thanks
Vinay -
Multiple SSID with different Login Web authority pages
Our current setup is one Anchor control and then several WLC’s, I want to know if I can have multiple SSID and use different Web Auth pages form them, so I can have a SSID that requires a password to Authentication access and another SSID that requires pass through Authentication but they would have different web authentication pages and go to different pages once Authenticated.
Is this possible to ?Hi,
If you are running WLC software 4.2 and above then u can do this on per WLAN basis.. here is the link which tells on how to do it..
http://www.cisco.com/en/US/tech/tk722/tk809/technologies_configuration_example09186a008067489f.shtml#A1
Lemme know if this answered ur question and please dont forget to rate the usefull posts!!
Regards
Surendra -
Is it possible to do multiple ssids and encryptions on an autonomous AP without vlans?
I got a customer who just has autonomous APs. They are upgrading from 1210s to 1262s. They are currently running a config that is wide open with no authentication or encryption and using a VPN tunnel on the wireless clients for security. They want to switch to using WPA2/PSK with the new APs. They have existing clients that have to continue to work during the upgrade to the new APs. They run 3 shifts so it is a 24 hr operation with no downtime. What I was thinking would be to configure the 1262 with multiple SSIDs, one with their existing settings and one with the new. Then I could swap the APs one at a time and it would only impact service for a short period of time while I was mounting the new AP. Then once all the new APs are installed I could transition the clients over to the new SSID and encryption then disable the old SSID once all the clients are switched over. I've done this before with a WLC but not with an autonomous APs. The only config examples I can find uses VLANs. This customer is not using VLANs. Is there anyway to use multiple SSIDs with different encryption on a single radio on an autonomous 1262 without VLANs?
The site has about 30 APs and 100 clients. Yes I know a controller would be preferred for a site of this size but that is a question for sales and why they didn't see them a controller. I just get stuck with what they sell them.
thanksHi Don,
Im afraid on the autonmous platform you can not map multiple WLANS to a single vlan.
"Satisfaction does not come from knowing the solution, it comes from knowing why." - Rosalind Franklin
"I'm in a serious relationship with my Wi-Fi. You could say we have a connection." -
How to execute "netsh wlan connect SSID", but SSID has space and quotation marks?
Dear all:
I have a wifi roruter with SSID test "3"
But when I execute following command netsh wlan connect "test \"3\""
the netsh reply: 未將設定檔 "test " 指派給指定的介面。
Sorry my windows7 is chinese version, but as you can see, netsh detect my SSID as
test, not test "3".
Does everybody know how to use netsh to connect to a SSID, and these SSID has space and quotation mark both?
Regards,
JosephHi Joseph,
Firstly, please modify your SSID name to make sure it do not contain spaces or special characters. SSID name is the router setting. please go there to change SSID name.
In addition, If only one SSID is specified in the profile, then the specified SSID is used to connect, and the ssid parameter is not required. If the profile specifies multiple SSIDs, the ssid parameter is required.
Therefore, I would like to suggest you run command as this syntax:
netsh wlan conncet ssid=Your SSID of the unsecured wireless network name=Your current profile name
To do this, please refer to the section “connect” in the following document:
Netsh Commands for Wireless Local Area Network (WLAN) Preliminary
http://technet.microsoft.com/en-us/library/cc755301.aspx#bkmk_wlanConn
Karen Hu
TechNet Community Support -
Hi team,
I have multiple SSID, but want users of a single SSID to be redirected to a HTTP or HTTPS URL (LAN SERVER for authentication)
I am very curious and it is important. I want to see how to achieve this with CISCO WLC !!!http://10.229.3.99/login.html?switch_url=https://1.1.1.1/login.html&ap_mac=e8:40:40:ad:cc:80&wlan=MO-GUEST&redirect=/login.html?switch_url=https://1.1.1.1/login.html&ap_mac=e8:40:40:ad:cc:80&wlan=MO-GUEST&redirect=/login.html?switch_url=https://1.1.1.1/login.html&ap_mac=e8:40:40:ad:cc:80&wlan=MO-GUEST&redirect=/login.html?switch_url=https://1.1.1.1/login.html&ap_mac=e8:40:40:ad:cc:80&wlan=MO-GUEST&redirect=/login.html?switch_url=https://1.1.1.1/login.html&ap_mac=e8:40:40:ad:cc:80&wlan=MO-GUEST&redirect=/login.html?switch_url=https://1.1.1.1/login.html&ap_mac=e8:40:40:ad:cc:80&wlan=MO-GUEST&redirect=/login.html?switch_url=https://1.1.1.1/login.html&ap_mac=e8:40:40:ad:cc:80&wlan=MO-GUEST&redirect=/login.html?switch_url=https://1.1.1.1/login.html&ap_mac=e8:40:40:ad:cc:80&wlan=MO-GUEST&redirect=10.229.3.99/login.html?switch_url=https://1.1.1.1/login.html&ap_mac=e8:40:40:ad:cc:80&wlan=MO-GUEST&redirect=www.geo.tv/
I wanted if someone connects to WLAN "MO-GUEST" automatically the user should be redirected to http://10.229.3.99/login.html and once authenticated by 10.229.3.99 , he/she should be allowed to access anything as normal. [ actually i just want automatic url redirection for the first time for the user of wlan "MO-GUEST"
waiting expert opinions. -
Multiple SSID's on the same subnet?
Can you have Multiple SSID's on the same subnet?
SSID1 authenticates clients via radius.
Our corporation bought printers with wireless cards that only support WPA-PSK so we created SSID2 for the printers. We can connect to both SSID's and ping from SSID1 to SSID2 but we can not perform other functions such as view the printer management interface with a browser. Should it be possibe to communicate between SSID1 and SSID2 on the same subnet?Yes you should have no issue, but the only thing is that you are using a lower security method... so either you put them on different subnets so you can control the traffic via acl's or might as well use the same security method to make it easier. The fact that you can ping sounds like you should be able to http to the device.
-
Using multiple SSID with AP 1100 (standalone mode).
Hi, need to configure 2 SSID on the same 1100 AP: open authentication and WPA2. It's possible to configure these 2 SSID without configuring VLAN's ?
On CCO I've read the following:
http://www.cisco.com/en/US/products/hw/wireless/ps430/products_qanda_item09186a008009483e.shtml
Q. How many service set identifiers (SSIDs) can you have per VLAN?
A. You can have only one SSID per VLAN. The use of multiple SSIDs over a single VLAN is not supported with Aironet APs.
It's also true with the latest IOS release ?Hi Roberto,
Hopefully the attached docs will answer your question:
Cisco Aironet 1100 Series
Using VLANs with Cisco Aironet Wireless Equipment
Deprecated versions of Cisco Aironet software permit binding multiple SSIDs to one VLAN. Current versions do not.
http://www.cisco.com/en/US/products/hw/wireless/ps4570/products_configuration_example09186a00801d0815.shtml#
Cisco IOS Software Configuration Guide for Cisco Aironet Access Points, 12.2(15)JA
Configuring Multiple SSIDs
vlan vlan-id
(Optional) Assign the SSID to a VLAN on your network. Client devices that associate using the SSID are grouped into this VLAN. You can assign only one SSID to a VLAN.
http://www.cisco.com/en/US/products/hw/wireless/ps4570/products_configuration_guide_chapter09186a00802085c4.html
Hope this helps!
Rob
Please remember to rate helpful posts....... -
Hello,
I am attempting to set up three Cisco 1242AG Wireless Access Points with multiple SSID's. I used the web interface and directions online to set up the two networks I want and at least one of the networks work wirelessly.
However, I have two problems:
The first, which is the most important, is that the "management" interface, BVI1, doesn't get an ip address from our DHCP server. I set the VLAN 60 (which you'll see in the documenation below) to be the native VLAN on the device as well as on the switch that the device is connected to as well as other settings in the configeration file below. Because of this, I can only manage the device via the console port which would be a huge pain once all of the devices are mounted.
The second problem is that I am not sure how to get both wireless networks broadcasting their SSID's. I have to manually type in the SSID for the second wireless network I have which I would prefer I don't have to. Anyway I can enable broadcasting on all of the SSID's?
Thank you for your time.
Regards,
Christopher Koeber
Using 7916 out of 32768 bytes
version 12.4
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
hostname AP-18.wesleysem.edu
enable secret {Number Here} {Encrypted Password Here}
enable password {Number Here} {Encrypted Password Here}
aaa new-model
aaa session-id common
dot11 syslog
dot11 vlan-name Kresge vlan 20
dot11 vlan-name Library vlan 30
dot11 vlan-name Public vlan 60
dot11 vlan-name Secure_Public vlan 70
dot11 vlan-name Secure_Seminary vlan 80
dot11 vlan-name Server_Room vlan 1
dot11 vlan-name Straughn vlan 40
dot11 vlan-name Trott vlan 10
dot11 vlan-name Web_Room vlan 50
dot11 ssid (Secure) Wesley Campus
vlan 80
authentication open
authentication key-management wpa version 2
wpa-psk ascii {Number Here} {WPA Key Here}
dot11 ssid Public
vlan 60
authentication open
mobility network-id 60
username Cisco password {Number Here} {Encrypted Password Here}
username admin privilege 15 secret {Number Here} {Encrypted Password Here}!
bridge irb
interface Dot11Radio0
no ip address
no ip route-cache
encryption vlan 80 mode ciphers aes-ccm
ssid (Secure) Campus
ssid Public
mbssid
station-role root
interface Dot11Radio0.1
encapsulation dot1Q 1
no ip route-cache
bridge-group 254
bridge-group 254 block-unknown-source
no bridge-group 254 source-learning
no bridge-group 254 unicast-flooding
bridge-group 254 spanning-disabled
interface Dot11Radio0.10
encapsulation dot1Q 10
no ip route-cache
bridge-group 10
bridge-group 10 subscriber-loop-control
bridge-group 10 block-unknown-source
no bridge-group 10 source-learning
no bridge-group 10 unicast-flooding
bridge-group 10 spanning-disabled
interface Dot11Radio0.20
encapsulation dot1Q 20
no ip route-cache
bridge-group 20
bridge-group 20 subscriber-loop-control
bridge-group 20 block-unknown-source
no bridge-group 20 source-learning
no bridge-group 20 unicast-flooding
bridge-group 20 spanning-disabled
interface Dot11Radio0.30
encapsulation dot1Q 30
no ip route-cache
bridge-group 30
bridge-group 30 subscriber-loop-control
bridge-group 30 block-unknown-source
no bridge-group 30 source-learning
no bridge-group 30 unicast-flooding
bridge-group 30 spanning-disabled
interface Dot11Radio0.40
encapsulation dot1Q 40
no ip route-cache
bridge-group 40
bridge-group 40 subscriber-loop-control
bridge-group 40 block-unknown-source
no bridge-group 40 source-learning
no bridge-group 40 unicast-flooding
bridge-group 40 spanning-disabled
interface Dot11Radio0.50
encapsulation dot1Q 50
no ip route-cache
bridge-group 50
bridge-group 50 subscriber-loop-control
bridge-group 50 block-unknown-source
no bridge-group 50 source-learning
no bridge-group 50 unicast-flooding
bridge-group 50 spanning-disabled
interface Dot11Radio0.60
encapsulation dot1Q 60 native
no ip route-cache
bridge-group 1
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
bridge-group 1 spanning-disabled
interface Dot11Radio0.70
encapsulation dot1Q 70
no ip route-cache
bridge-group 70
bridge-group 70 subscriber-loop-control
bridge-group 70 block-unknown-source
no bridge-group 70 source-learning
no bridge-group 70 unicast-flooding
bridge-group 70 spanning-disabled
interface Dot11Radio0.80
encapsulation dot1Q 80
no ip route-cache
bridge-group 80
bridge-group 80 subscriber-loop-control
bridge-group 80 block-unknown-source
no bridge-group 80 source-learning
no bridge-group 80 unicast-flooding
bridge-group 80 spanning-disabled
interface Dot11Radio1
no ip address
no ip route-cache
shutdown
encryption vlan 80 mode ciphers aes-ccm
dfs band 3 block
channel dfs
station-role root
interface Dot11Radio1.1
encapsulation dot1Q 1
no ip route-cache
bridge-group 254
bridge-group 254 block-unknown-source
no bridge-group 254 source-learning
no bridge-group 254 unicast-flooding
bridge-group 254 spanning-disabled
interface Dot11Radio1.10
encapsulation dot1Q 10
no ip route-cache
bridge-group 10
bridge-group 10 subscriber-loop-control
bridge-group 10 block-unknown-source
no bridge-group 10 source-learning
no bridge-group 10 unicast-flooding
bridge-group 10 spanning-disabled
interface Dot11Radio1.20
encapsulation dot1Q 20
no ip route-cache
bridge-group 20
bridge-group 20 subscriber-loop-control
bridge-group 20 block-unknown-source
no bridge-group 20 source-learning
no bridge-group 20 unicast-flooding
bridge-group 20 spanning-disabled
interface Dot11Radio1.30
encapsulation dot1Q 30
no ip route-cache
bridge-group 30
bridge-group 30 subscriber-loop-control
bridge-group 30 block-unknown-source
no bridge-group 30 source-learning
no bridge-group 30 unicast-flooding
bridge-group 30 spanning-disabled
interface Dot11Radio1.40
encapsulation dot1Q 40
no ip route-cache
bridge-group 40
bridge-group 40 subscriber-loop-control
bridge-group 40 block-unknown-source
no bridge-group 40 source-learning
no bridge-group 40 unicast-flooding
bridge-group 40 spanning-disabled
interface Dot11Radio1.50
encapsulation dot1Q 50
no ip route-cache
bridge-group 50
bridge-group 50 subscriber-loop-control
bridge-group 50 block-unknown-source
no bridge-group 50 source-learning
no bridge-group 50 unicast-flooding
bridge-group 50 spanning-disabled
interface Dot11Radio1.60
encapsulation dot1Q 60 native
no ip route-cache
bridge-group 1
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
bridge-group 1 spanning-disabled
interface Dot11Radio1.70
encapsulation dot1Q 70
no ip route-cache
bridge-group 70
bridge-group 70 subscriber-loop-control
bridge-group 70 block-unknown-source
no bridge-group 70 source-learning
no bridge-group 70 unicast-flooding
bridge-group 70 spanning-disabled
interface Dot11Radio1.80
encapsulation dot1Q 80
no ip route-cache
bridge-group 80
bridge-group 80 subscriber-loop-control
bridge-group 80 block-unknown-source
no bridge-group 80 source-learning
no bridge-group 80 unicast-flooding
bridge-group 80 spanning-disabled
interface FastEthernet0
ip dhcp client update dns
no ip address
no ip route-cache
duplex auto
speed auto
interface FastEthernet0.1
encapsulation dot1Q 1
no ip route-cache
bridge-group 254
no bridge-group 254 source-learning
bridge-group 254 spanning-disabled
interface FastEthernet0.10
encapsulation dot1Q 10
no ip route-cache
bridge-group 10
no bridge-group 10 source-learning
bridge-group 10 spanning-disabled
interface FastEthernet0.20
encapsulation dot1Q 20
no ip route-cache
bridge-group 20
no bridge-group 20 source-learning
bridge-group 20 spanning-disabled
interface FastEthernet0.30
encapsulation dot1Q 30
no ip route-cache
bridge-group 30
no bridge-group 30 source-learning
bridge-group 30 spanning-disabled
interface FastEthernet0.40
encapsulation dot1Q 40
no ip route-cache
bridge-group 40
no bridge-group 40 source-learning
bridge-group 40 spanning-disabled
interface FastEthernet0.50
encapsulation dot1Q 50
no ip route-cache
bridge-group 50
no bridge-group 50 source-learning
bridge-group 50 spanning-disabled
interface FastEthernet0.60
encapsulation dot1Q 60 native
no ip route-cache
bridge-group 1
no bridge-group 1 source-learning
bridge-group 1 spanning-disabled
interface FastEthernet0.70
encapsulation dot1Q 70
no ip route-cache
bridge-group 70
no bridge-group 70 source-learning
bridge-group 70 spanning-disabled
interface FastEthernet0.80
encapsulation dot1Q 80
no ip route-cache
bridge-group 80
no bridge-group 80 source-learning
bridge-group 80 spanning-disabled
interface BVI1
ip address dhcp client-id FastEthernet0
no ip route-cache
ip http server
no ip http secure-server
ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
bridge 1 route ip
line con 0
line vty 0 4
endI am using a third party DHCP server which is our Windows Domain Controller. I have the ip helper-address set for the native vlan of the Access Point through a layer 3 distribution switch (a Catalyst 4506) that the current switch connects to.
I didn't see any event on the logs for the AP.
Let me know if I need to do something else.
Thanks. -
WAP200 and .1x/radius authentication with multiple SSIDs
Apparently it's not possible to define more than a single radius server when using multiple SSIDs with WAP200. Unfortunately WAP200 doesn't add the name of the SSID as a radius attribute, so it's not possible to make distinction whether the user is trying to log in to SSID A or B. Does anyone have any ideas or workarounds for this limitation? Of course the best solution would be if Cisco/Linksys fixed the firmware so that the SSID of the logging in user would be sent to the radius server as an extra attribute or appended to the client mac address.
Security option for an SSID can be unique and can be configured when you configure a SSID or under VLAN . Note that each vlan is uniquely mapped to induvidual SSID.
-
Authentication with Multiple SSIDs AP521G, using Autonomous
I have an AP521G access point that I am trying to setup authentication for multiple SSIDs. One SSID is for domain users with WPA/TKIP authentication to a radius server and the other SSID is for guest to have access to Internet with no authentication. Is there a way to setup both SSIDs on the AP for this configuration?
Security option for an SSID can be unique and can be configured when you configure a SSID or under VLAN . Note that each vlan is uniquely mapped to induvidual SSID.
-
Multiple SSIDS with VLAN ACL seperation
Hi,
I have bought a 887W and I'm new to wireless on a router, I need advice about seperating multiple SSIDs with access list.
I have configured 2 SSIDs one for 'trusted' clients and one for 'guest' clients. I want to prevent the 'guest' SSID obtaining access to the other vlan/SSID using an ACL.
Each SSID is associated with a BVI, the BVI has the IP address, then it's linked to a seperated VLAN interface, then each VLAN.
Thanks if you can help...
DaveSolved my issue, I simply attached the ACLs to the BVI interfaces. Fairly obvious, but I read a Cisco webpage that said this could not be done, although this may have been a temporary bug that has been fixed.
-
Multiple SSIDS and disappearing
We have Cisco 3602i access points for the most part, all of which advertise multiple SSIDs.
Very occasionally we see an SSID completely disappear from view, even though others remain solid (I can't say it's all devices as the majority of people who raise the issue have apple devices, but there are the odd one or two who use Windows laptops).
Also, the RSSI seems to fluctuate wildly.
I should add that we have disabled up to 11mbps data rates on the controller and we're running 7.6.100.0 currently, but plan to upgrade to 7.6.110.0 tonight.
I guess my question is how can an SSID just drop off the client view if others on the same AP are fine?
How does the AP deal with multiple SSIDs and does it prioritise?
I have to add that I've never had this issue and I'm just using a company standard HP laptop with an Intel chipset.Hello,
See my comments:
Also, the RSSI seems to fluctuate wildly.
A: This is often how a device hears the frames. Sometimes in high interference you can epxect this to jump around. I normally like to see if all the devices are doing this or just a select few. Sometimes poor clients jump around more than others.
I should add that we have disabled up to 11mbps data rates on the controller and we're running 7.6.100.0 currently, but plan to upgrade to 7.6.110.0 tonight.
A: I dont think turning off lower rates are bad unless your WiFi cant support the design. Good call get on the latest.
I guess my question is how can an SSID just drop off the client view if others on the same AP are fine?
A: Again, its a client missing frames like beacons.
How does the AP deal with multiple SSIDs and does it prioritise?
A: This SSIDs are virtualized. I blogged how this is done:
http://www.my80211.com/home/2011/5/2/wlc-how-cisco-virtualizes-the-base-radio-mac-address-on-the.html
I have to add that I've never had this issue and I'm just using a company standard HP laptop with an Intel chipset.
A: Again I think if you search you might see this is more around specific devices. I would do a packet capture and see what is going on. Recently had to troubleshoot an Android only to find out it was just bad wifi client. Always sending NULL frames and scanning and not passing traffic -
Multiple SSIDs/VLAN - NPS Authentication
I have recently set up a similar network using Ruckus equipment; however, need to do it now with Cisco...
I have a multiple SSIDs associated to different VLANs broadcasting. I would like to configure a single Radius server pointed to my NPS server and allow for authentication by group to each SSID.
With Ruckus I had to put in a vendor specific custom attribute and then use Roles to allow access by AD Security Group.
Does anyone know how to setup something similar with Cisco? I just need a single group to be able to autheticate to each SSID.
Josh PriceThis is pretty straightforward.
Just create a NPS policy for each SSID.
A simple policy could check 3 conditions.
Windows Groups = DOMAIN\GroupABC
Called Station ID = .*:SSIDNAME$
NAS Port ID = Wireless IEEE or Wireless Other
Just change SSIDNAME to whatever the specific SSID is, and obviously the group that you want mapped. The SSID condition uses regex.
Cheers
Peter -
Hi, I'm looking to set up an Wireless network using Multiple SSID's (Business and Guest) using one airport extreme and three Airport Expresses.
Are the Airport Expresses capable of bridging multiple ssids or extending multiple ssids?
What's the best practice on setting this up?
Regards,
MikeBy default, the AirPort Extreme will provide a simultaneous dual band signal for the "main" network, with both the 2.4 GHz and 5 GHz bands using the same wireless network name. You could think of this as your Business network.
Wireless devices will connect to the 2.4 GHz or 5 GHz band based on their capabilities and distance from the AirPort Extreme.
For example, most iPhones can only connnect to 2.4 GHz, so that is where they will connect. A newer laptop will be able to connect to either 2.4 GHz or 5 GHz.
5 GHz signals are faster, but much weaker than 2.4 GHz signals, so the 5 GHz signals tend to be pretty much a line-of-sight or close proximity type of connection. In other words, if a laptop is in cloxe proximity to the AirPort Extreme, it will likely connect to the 5 GHz band. If the laptop moves a few rooms away, it will likey connect to the 2.4 GHz band.
The AirPort Extreme does have an option to enable a Guest Network......IF.....you plan to connect the AirPort Extreme to a simple modem....not a modem/router or gateway type of device.
If you are not sure what you have, post back with the make and model number of your "modem". If you do not have the right type of modem, you will not be able to configure a Guest Network.
Important.....the Guest Network cannot be extended. The signal will only be produced by the AirPort Extreme.
I assume that you want to use the Express devices to "extend" the signal using wireless only.
Since the AirPort Express models that you have are not simultaneous dual band devices, they will be able to extend one band of the AirPort Extreme's wireless signal. In most cases, the Express will extend the 2.4 GHz band, since it is the stronger signal.
Each AirPort Express connects to the AirPort Extreme's signal, so each AirPort Express will need to be located where it can receive a strong wireless signal from the AirPort Extreme.
It would be better if you could connect each AirPort Express to the AirPort Extreme using a wired Ethernet connection. This would allow you to locate each AirPort Express exactly where it will be needed.
Maybe you are looking for
-
How do you change the first letter of a new line from uppercase to lowercase?
In filling in case sensitive id's and passwords, the iPad automatically capitalizes the first letter---how do you change to lower case?
-
HT4623 update ipad with ios 4.3
how do I update ipad with ios 4.3
-
Back up afte installing 3.0 software
Hi Please can someone help, I am trying to update my iphone with the new 3.0 software, and it started the back yesterday at 10.00 and 24 hours later it isn't even half way, I have delete most of my photo's leaving about 5 and all of my added on apps
-
Newbie Needs direction of where to look
I am new to Jdeveloper 11g and still quite new to Oracle 11g. I have a simple table in Oracle which I have brought into Jdeveloper by creating a Web Fusion Application. Within the App I have created 2 views of the same table. The first View I have bo
-
Slideshow - not displaying external adjustments
when i start a sliding show in aperture, the external adjusted pictures are displayed without adjustements, but those which were adjusted in aperture are shown in the right way. my workflow: importing pics to aperture, adjusting all of them first in