WLAN Profile Name siginificance.

Hi all,
I'm fairly new to the Cisco WLAN architecture and am curious what siginificance the 'Profile Name' associated to an SSID has locally on the WLC?  We have 8 SSIDs all with unique profile names and, I believe, the profile name is only locally siginificant to distinguish between SSIDs that have the same name (with differing L2 security policies).
Is this correct? If not, can anyone tell me what other significance the profile name plays in the authentication/assocation of a client with a particular SSID.
Many Thanks

David,
     you are correct.  the profile name is so you can have a 'migration' ssid, where you use the same SSID, but have different security mechanisms for each one.
Steve

Similar Messages

  • Netsh wlan show profiles name=[profile name] key=clear batch file

    i want to make a bat.file for this command : netsh
    wlan show profiles name=[profile name] key=clear.
    when i start the bat.file, i want to only write in the network name, and just press enter. and then the network key will show.
    can you help me please??
    ps, sorry for bad english...

    i want to make a bat.file for this command : netsh
    wlan show profiles name=[profile name] key=clear.
    when i start the bat.file, i want to only write in the network name, and just press enter. and then the network key will show.
    can you help me please??
    ps, sorry for bad english...
    i think something like this(can't finish, because don't know how), and i dont ewen know if this command is properly written, please edith and share it. :)
    @echo off
    :home
    title net password
    color a
    cls
    echo.
    echo network
    echo=============
    echo.
    echo [1] input ssid
    echo [2] exit
    echo.
    set /p op=
    if %op%==1 goto 1
    if %op%==2 goto 2
    :1
    color a
    cls
    echo network key
    echo ================================
    echo.
    Set /p username=Username:
    netsh wlan show profiles name=[username] key=clear

  • WLAN Profile question

    We happen to have a very large open wireless implementation that uses an external webauth page that authenticates against our RADIUS.  We are also using the Lobby Ambassador for employees that drop in for a week or two at a time, and those users are on the same SSID as everyone else.
    For obvious reasons, we want to secure our SSID with WPA2-802.1x.  When we do this our Lobby Ambassador will no longer function since those temporary usernames and passwords will be in the controllers.
    My question is this:  Is there a way to use WLAN Profiles so that I can have a profile for WPA2 and our Lobby Ambassador under the same SSID?   I understand the Lobby Ambassador users won't be secure and this isn't the best practice, but can it be done?
    Thanks in advance,
    Tim

    /* Style Definitions */
    table.MsoNormalTable
    {mso-style-name:"Table Normal";
    mso-tstyle-rowband-size:0;
    mso-tstyle-colband-size:0;
    mso-style-noshow:yes;
    mso-style-priority:99;
    mso-style-qformat:yes;
    mso-style-parent:"";
    mso-padding-alt:0cm 5.4pt 0cm 5.4pt;
    mso-para-margin:0cm;
    mso-para-margin-bottom:.0001pt;
    mso-pagination:widow-orphan;
    font-size:11.0pt;
    font-family:"Calibri","sans-serif";
    mso-ascii-font-family:Calibri;
    mso-ascii-theme-font:minor-latin;
    mso-fareast-font-family:"Times New Roman";
    mso-fareast-theme-font:minor-fareast;
    mso-hansi-font-family:Calibri;
    mso-hansi-theme-font:minor-latin;}
    Hi Tim
    No, you can’t have different security policy under one SSID. If you enable WPA/WPA2 with 802.1X, all client must use this to authenticate. But there shouldn’t be any problem to have two SSID, one for employees and one for external users, like guests and consultants.
    Kind Regards
    Johan

  • I had renamed my user login name and assumed that there will be no change in the settings and files. When I login with the new profile name everything is gone. How can I get back all my files and settings?

    I had renamed my user login name and assumed that there will be no change in the settings and files. When I login with the new profile name everything is gone. How can I get back all my files and settings? Please help. Thanks.

    You should have asked this before you tried: Changing username or short name- User Account and Short Name- OS X- How to change user account name or home directory name.

  • Significance of profile name in configuration profile

    Hi all experts in SD,
    I am involved in variant configuration. I had a little confusion, for which i had searched the forum but dint find any relevant topic.
    While creating configuration profile with CU41 of a configurable material we need to enter 'profile name' . We can enter many profile names for a single configuration profile. I am confused over it that what exactly is the need for having many profile names for a single configuration profile.
    What i can infer is that with many profile names being provided in the configuration profile the single configurable material material can be used with many names in different scenarios.
    Please do correct me if i am wrong . If at all i m true then also please provide me some more information related to it.
    Thanks in advance for the solution.
    Regards,
    Gaurav Kumar

    u need to check with the sap website

  • Change profile name in iMessage

    how do I change the profile name "jabber" on imessage?

    Hi Simon,
    Happy Holidays!  Are you trying to change the name of the Jabber service on your Mac?  Here's how:
    Mac Basics: Messages helps you chat instantly - Apple Support
    http://support.apple.com/en-us/HT202549
    In Messages select Messages > Preferences.
    Click the Accounts button.
    Select the Jabber account on the left.
    In the Account Information tab, change the Description field to whatever name you want.
    Close the Accounts window (red dot in top-left corner).
    Quit Messages and then launch the application again.
    I hope this information helps ....
    - Judy

  • Determine ICC output profile (name) in PDF/X output intent

    Hi all,
    I have a PDF of which I need to determine the ICC output profile (name) of the PDF/X output intent. This is what I have in the 'content stream':
    <</Metadata 6 0 R/OutputIntents[<</DestOutputProfile 7 0 R/Info(OFCOM. ISO 12647-2:2004 / Amd 1, Offset commercial and specialty printing according to ISO 12647-2, paper type 1 or 2 \(gloss or matte coated offset, 115 g/m2\), screen frequency 60/cm.)/OutputConditionIdentifier(FOGRA39)/RegistryName(http://www.color.org)/S/GTS_PDFX/Type/OutputIntent>>]
    How can I, based on this information, determine what the name of the ICC profile in the PDF/X output intent is? Adobe Acrobat's output preview tells me that is should say / find ''ISO Coated v2 300% (ECI)'.
    Thanks in advance.
    Didier

    Thanks! Thought it would be something in that direction. Any tools or libraries you might know that can be used to extract and parse this kind of information (as part of a preflight process or something else)? Adobe tools for instance?

  • How to get the profile name

    I did not know how to get the profile name in photoshop file using javascript? Kindly help me.

    var myDocProfile = app.activeDocument.colorProfileName;

  • RADIUS/DECODE: parse unknown cisco vsa "profile-name" - IGNORE

    Dear Team,
    I have faced an issue with dot1x mab authorization between cisco switch 3750 and ISE 1.1. I have cisco IP phone connected on port # gig1/0/1 to authenticated through MAB with cisco ISE
    int gig 1/0/1
    switchport mode access
    switchport access vlan 9
    switchport voice vlan 410
    authentication order mab dot1x
    authentication priority dot1x mab
    spanning-tree portfast
    authentication host-mode multi-domain
    authentication port-control auto
    dot1x pae authenticator
    mab
    dot1x timeout tx-period 3
    dot1x max-reauth-req 2
    authentication periodic
    authentication timer reauthenticate server
    I can get authentication successfuly but can't download the authorization profile on the gig1/0/1 port since I can see that everything seems fine from the ISE side. the phone is authenticated and authorized fine. so, I debug the dot1x & radius flows from the switch side and get this result.
    RADIUS/ENCODE(00000043):Orig. component type = Dot1X
    RADIUS(00000043): Config NAS IP: 1.1.1.2
    RADIUS(00000043): Config NAS IPv6: ::
    RADIUS/ENCODE(00000043): acct_session_id: 57
    RADIUS(00000043): sending
    RADIUS(00000043): Sending a IPv4 Radius Packet
    RADIUS(00000043): Send Access-Request to 1.1.1.1:1812 id 1645/72, len 261
    RADIUS:  authenticator 82 94 D8 85 E9 E0 CF 71 - 03 FE C5 BA 76 EC 76 C4
    RADIUS:  User-Name           [1]   14  "00152bd20c19"
    RADIUS:  User-Password       [2]   18  *
    RADIUS:  Service-Type        [6]   6   Call Check                [10]
    RADIUS:  Vendor, Cisco       [26]  31 
    RADIUS:   Cisco AVpair       [1]   25  "service-type=Call Check"
    RADIUS:  Framed-MTU          [12]  6   1500                     
    RADIUS:  Called-Station-Id   [30]  19  "30-F7-0D-CD-5F-01"
    RADIUS:  Calling-Station-Id  [31]  19  "00-15-2B-D2-0C-19"
    RADIUS:  Message-Authenticato[80]  18 
    RADIUS:   90 B9 61 65 CC A6 B2 89 BC C8 3D DC D4 14 03 C5               [ ae=]
    RADIUS:  EAP-Key-Name        [102] 2   *
    RADIUS:  Vendor, Cisco       [26]  49 
    RADIUS:   Cisco AVpair       [1]   43  "audit-session-id=C0A8424200000036001B2AAE"
    RADIUS:  NAS-Port-Type       [61]  6   Ethernet                  [15]
    RADIUS:  NAS-Port            [5]   6   50101                    
    RADIUS:  NAS-Port-Id         [87]  22  "GigabitEthernet1/0/1"
    RADIUS:  Called-Station-Id   [30]  19  "30-F7-0D-CD-5F-01"
    RADIUS:  NAS-IP-Address      [4]   6   1.1.1.2                  
    RADIUS(00000043): Started 5 sec timeout
    RADIUS: Received from id 1645/72 1.1.1.1:1812, Access-Accept, len 297
    RADIUS:  authenticator D5 2C 29 3B AC C8 A7 2F - A4 75 45 F5 51 6D 4F A8
    RADIUS:  User-Name           [1]   19  "00-15-2B-D2-0C-19"
    RADIUS:  State               [24]  40 
    RADIUS:   52 65 61 75 74 68 53 65 73 73 69 6F 6E 3A 43 30  [ReauthSession:C0]
    RADIUS:   41 38 34 32 34 32 30 30 30 30 30 30 33 36 30 30  [A842420000003600]
    RADIUS:   31 42 32 41 41 45            [ 1B2AAE]
    RADIUS:  Class               [25]  50 
    RADIUS:   43 41 43 53 3A 43 30 41 38 34 32 34 32 30 30 30  [CACS:C0A84242000]
    RADIUS:   30 30 30 33 36 30 30 31 42 32 41 41 45 3A 69 73  [00036001B2AAE:is]
    RADIUS:   65 33 2F 31 35 30 33 30 36 35 37 38 2F 33 38 36  [ e3/150306578/386]
    RADIUS:  Termination-Action  [29]  6   1                        
    RADIUS:  Message-Authenticato[80]  18 
    RADIUS:   09 17 84 AB 27 8E B4 E0 F4 A6 93 EE 19 2A A6 34               [ '*4]
    RADIUS:  Vendor, Cisco       [26]  34 
    RADIUS:   Cisco AVpair       [1]   28  "device-traffic-class=voice"
    RADIUS:  Vendor, Cisco       [26]  75 
    RADIUS:   Cisco AVpair       [1]   69  "ACS:CiscoSecure-Defined-ACL=#ACSACL#-IP-PERMIT_ALL_TRAFFIC-4fe7f797"
    RADIUS:  Vendor, Cisco       [26]  35 
    RADIUS:   Cisco AVpair       [1]   29  "profile-name=Cisco-IP-Phone"i
    RADIUS(00000043): Received from id 1645/72
    RADIUS/DECODE: parse unknown cisco vsa "profile-name" - IGNORE
    %MAB-5-SUCCESS: Authentication successful for client (0015.2bd2.0c19) on Interface Gi1/0/1 AuditSessionID C0A8424200000036001B2AAE
    %AUTHMGR-7-RESULT: Authentication result 'success' from 'mab' for client (0015.2bd2.0c19) on Interface Gi1/0/1 AuditSessionID C0A8424200000036001B2AAE
    %DOT1X_SWITCH-5-ERR_VLAN_RSPAN: Attempt to assign RSPAN VLAN 410 to 802.1x port GigabitEthernet1/0/1. 802.1x is incompatible with RSPAN AuditSessionID C0A8424200000036001B2AAE
    RADIUS/ENCODE(00000000):Orig. component type = Invalid
    so, I notice two things :-
    1-" RADIUS/DECODE: parse unknown cisco vsa "profile-name" - IGNORE " on the radius attribute since I beleive that I configure the radius vsa attribute fine as shows
    aaa new-model
    aaa authentication dot1x default group radius
    aaa authorization network default group radius
    aaa accounting dot1x default start-stop group radius
    aaa accounting system default start-stop group radius
    aaa session-id common
    aaa accounting update periodic 5
    aaa server radius dynamic-author
    client 1.1.1.1 server-key 0 cisco
    radius-server attribute 8 include-in-access-req
    radius-server attribute 25 access-request include
    radius-server dead-criteria time 5 tries 3
    radius-server host 1.1.1.1 auth-port 1812 acct-port 1813 key cisco
    radius-server vsa send accounting
    radius-server vsa send authentication
    2- "%DOT1X_SWITCH-5-ERR_VLAN_RSPAN:" since I didn't have any configuration related to RSPAN.
    so, anybody have any idea to fix this issue.
    Regards
    Basel

    It is not the ACL it is ignoring, it's the profile-name, which it should, because it has nothing to use that for. However, you should look into VLAN 410, to check and see if you have any config relating to that vlan, the only actual error i see in your logs is the one regarding assigning vlan 410. Could you please post you entire switch config, see we can see what else you might have configured.
    %DOT1X_SWITCH-5-ERR_VLAN_RSPAN:  Attempt to assign RSPAN VLAN 410 to 802.1x port GigabitEthernet1/0/1.  802.1x is incompatible with RSPAN AuditSessionID  C0A8424200000036001B2AAE - See more at:  https://supportforums.cisco.com/message/3863298#3863298
    %DOT1X_SWITCH-5-ERR_VLAN_RSPAN:  Attempt to assign RSPAN VLAN 410 to 802.1x port GigabitEthernet1/0/1.  802.1x is incompatible with RSPAN AuditSessionID  C0A8424200000036001B2AAE - See more at:  https://supportforums.cisco.com/message/3863298#3863298
    %DOT1X_SWITCH-5-ERR_VLAN_RSPAN:  Attempt to assign RSPAN VLAN 410 to 802.1x port GigabitEthernet1/0/1.  802.1x is incompatible with RSPAN AuditSessionID  C0A8424200000036001B2AAE - See more at:  https://supportforums.cisco.com/message/3863298#3863298
    %DOT1X_SWITCH-5-ERR_VLAN_RSPAN:  Attempt to assign RSPAN VLAN 410 to 802.1x port GigabitEthernet1/0/1.  802.1x is incompatible with RSPAN AuditSessionID  C0A8424200000036001B2AAE - See more at: https://supportforums.cisco.com/message/3863298#3863298
    %DOT1X_SWITCH-5-ERR_VLAN_RSPAN:  Attempt to assign RSPAN VLAN 410 to 802.1x port GigabitEthernet1/0/1.  802.1x is incompatible with RSPAN AuditSessionID  C0A8424200000036001B2AAE - See more at: https://supportforums.cisco.com/message/3863298#3863298
    %DOT1X_SWITCH-5-ERR_VLAN_RSPAN:  Attempt to assign RSPAN VLAN 410 to 802.1x port GigabitEthernet1/0/1.  802.1x is incompatible with RSPAN AuditSessionID  C0A8424200000036001B2AAE - See more at: https://supportforums.cisco.com/message/3863298#3863298
    %DOT1X_SWITCH-5-ERR_VLAN_RSPAN:  Attempt to assign RSPAN VLAN 410 to 802.1x port GigabitEthernet1/0/1.  802.1x is incompatible with RSPAN AuditSessionID  C0A8424200000036001B2AAE - See more at: https://supportforums.cisco.com/message/3863298#3863298
    %DOT1X_SWITCH-5-ERR_VLAN_RSPAN:  Attempt to assign RSPAN VLAN 410 to 802.1x port GigabitEthernet1/0/1.  802.1x is incompatible with RSPAN AuditSessionID  C0A8424200000036001B2AAE - See more at: https://supportforums.cisco.com/message/3863298#3863298
    %DOT1X_SWITCH-5-ERR_VLAN_RSPAN:  Attempt to assign RSPAN VLAN 410 to 802.1x port GigabitEthernet1/0/1.  802.1x is incompatible with RSPAN AuditSessionID  C0A8424200000036001B2AAE - See more at: https://supportforums.cisco.com/message/3863298#3863298

  • Automatic provision of WLAN profiles to cliets through ISE

    Hi All,
    Our customer was using L3 web auth for corporate users . LDAP was integrated directly with WLC for authentication . Now they want to use L2 web authentication WPA2/PEAP for corporate users . As per my understanding for using L2 auth , we need to create the appropriate SSID profile in end user laptops in order to associate with the SSID . Wheras L3 web auth , dont require that . Simply connect -> then open browser -> redirect to captive portal -> authentication. Customer was habituated with that.
    Hence they dont want to manually create the SSID profiles in laptops . They hav got base ISE licnese(only for AAA). So is there any option to provide the WLAN profiles to customer laptops and mobile devices with the help of ISE .
    Thanks,
    Vijay

    Hi Scott ,
    This way users can click on the SSID and use their AD credentials to  connect. Once they connect, the device will creat a profile and store it  on the device.
    So you mean to say , no need of creating the profile manually in laptop ? We have broadcasted test SSID with WPA2/AES . When we connect to the SSID with win 7 laptops its not asking for AD credentials . Simply it gives errror not able to connect. But when we manually configured the SSID in laptop and connect , it asks for credentials and succeed.
    For latest mobiles , when we connect to the test SSID. it asks the credentials directly and succeed. The issue is for laptops only , that we need to create the SSID prfile manualy in laptops.

  • How can one edit a profile name in ACR?

    Both Adobe DNG Profile Utility and the PassPort profile software very nicely create and install profiles in ACR.  A profile name is given at the time of creation. Once installed in ACR, however, how can one edit the name of the profile?
    thanks, grampus45

    http://forums.adobe.com/message/3158961#3158961

  • Change profile name on support form

    Can anyone tell me how do I change my profile name on this support forum?

    Hello,
    You cannot...once created, it is permanent. To change would require admin access...if really necessary, click the "Report Inappropriate Content" link on the left side of any of your posts and ask for the change you desire.
    Good luck!
    Occam's Razor nearly always applies when troubleshooting technology issues!
    If anyone has been helpful to you, please show your appreciation by clicking the button inside of their post. Please click here and read, along with the threads to which it links, for helpful information to guide you as you proceed. I always recommend that you treat your BlackBerry like any other computing device, including using a regular backup schedule...click here for an article with instructions.
    Join our BBM Channels
    BSCF General Channel
    PIN: C0001B7B4   Display/Scan Bar Code
    Knowledge Base Updates
    PIN: C0005A9AA   Display/Scan Bar Code

  • Color space/profile name

    I have some pictures that don't show a thumbnail in iPhoto. The info dialog for them says the Color Space is "Gray" and the Profile name is "Gr?skala - gamma 2,2". If I double-click on of these the enlarged image seems somewhat faded. The picture looks fine if I just view it directly in Preview, or ColorSync Utility. It seems most pictures have a Color Space of RGB, how to I change the Color Space of these files to RGB?

    Justin:
    Download the Automator application "Embed sRGB Profile" from Toad's Cellar and unzip it. Then locate the original files for those problem images and drop them on it. Next launch iPhoto with the Command+Option keys depressed and follow the instructions to rebuild the library and select the first three options. This should get those images compatible with iPhoto.
    Do you Twango?
    TIP: For insurance against the iPhoto database corruption that many users have experienced I recommend making a backup copy of the Library6.iPhoto database file and keep it current. If problems crop up where iPhoto suddenly can't see any photos or thinks there are no photos in the library, replacing the working Library6.iPhoto file with the backup will often get the library back. By keeping it current I mean backup after each import and/or any serious editing or work on books, slideshows, calendars, cards, etc. That insures that if a problem pops up and you do need to replace the database file, you'll retain all those efforts. It doesn't take long to make the backup and it's good insurance.
    I've written an Automator workflow application (requires Tiger), iPhoto dB File Backup, that will copy the selected Library6.iPhoto file from your iPhoto Library folder to the Pictures folder, replacing any previous version of it. You can download it at Toad's Cellar. Be sure to read the Read Me pdf file.

  • HT4314 Please I want my Game Center profile name back I changed it by mistake and when I try to return it it tell me the nickname is already in use!

    Please I want my Game Center profile name back I changed it by mistake and when I try to return it it tell me the nickname is already in use!

    Restore the device from the most recent backup (prior to restoring as new) to put everything back the way it was.

  • How to check on which APs a wlan profile is activated on WLC4402

    Hello,
    we use a wlc4402 and several wlan profiles which are activated on different access-points (wlan override).
    Does anybody know if there is a possibility to see a summary list of the aps on which a certain wlan profile is activated?
    Best Regards,
    Thorsten

    Hello,
    I tested it but did not get the output I am looking for.
    What I am looking for is a list of all wlan profiles and for each wlan profile a list of all ap where it's activated, e.g.:
    wlan profile 1
    ap1
    ap2
    ap3
    wlan profile 2
    ap2
    ap5
    ap7
    Does anybody further know how I can set the cli terminal length to 0 so that there is no page break (as term len 0 in ios)?
    Regards,
    Thorsten

Maybe you are looking for