Wlan rtl8191se causes freeze on arch64

Hello,
i've got a new Toshiba L505-10j with realtek rtl8192se wlanadapter. There is no Linux-support for this one, so I had to install them by myself... I found drivers from realtek in a forum. They where on the official site only for a couple of days. I installed them with "make install". The interface was found after a reboot. After using Wlan-Connection a few seconds my system freezes. I tried networkmanager and wicd with the same effect.
I tried the same with GNU/Linux Mint(also x86_64) and I coud use my network without problems, so it should be a problem of arch/arch64.
I've also tried ndiswrapper, but it only works with 32bit.
uname -a
Linux cyberwinnie 2.6.31-ARCH #1 SMP PREEMPT Tue Nov 10 19:01:40 CET 2009 x86_64 Intel(R) Core(TM)2 Duo CPU P7450 @ 2.13GHz GenuineIntel GNU/Linux
/var/log/kernel.log
ov 24 17:11:04 cyberwinnie kernel: pci 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
Nov 24 17:11:07 cyberwinnie kernel: r8169: eth0: link down
Nov 24 17:11:07 cyberwinnie kernel: ADDRCONF(NETDEV_UP): eth0: link is not ready
Nov 24 17:11:07 cyberwinnie kernel: gen_RefreshLedState first init
Nov 24 17:11:07 cyberwinnie kernel: =================> NIC version : C-cut
Nov 24 17:11:07 cyberwinnie kernel: rtl819xSE 0000:14:00.0: firmware: requesting RTL8192SE/rtl8192sfw.bin
Nov 24 17:11:07 cyberwinnie kernel: ===>rtl8192_SetWirelessMode(), wireless_mode:0x8, support_mode:0x16
Nov 24 17:11:07 cyberwinnie kernel: <===rtl8192_SetWirelessMode(), wireless_mode:10, bEnableHT = 1
Nov 24 17:11:07 cyberwinnie kernel: ===>ieee80211_start_scan_rsl()
Nov 24 17:11:07 cyberwinnie kernel: ADDRCONF(NETDEV_UP): wlan0: link is not ready
Nov 24 17:11:09 cyberwinnie kernel: ====================>haha:IPSEnter()
Nov 24 17:11:09 cyberwinnie kernel: =========>NicIFDisableNIC()
Nov 24 17:11:09 cyberwinnie kernel: PHY_SetRtl8192seRfHalt save BB/RF
Nov 24 17:11:10 cyberwinnie kernel: r8169: eth0: link up
Nov 24 17:11:10 cyberwinnie kernel: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
Nov 24 17:11:13 cyberwinnie kernel: =========>r8192_wx_set_scan(): IPSLeave
Nov 24 17:11:13 cyberwinnie kernel: ===========>NicIFEnableNIC()
Nov 24 17:11:13 cyberwinnie kernel: gen_RefreshLedState first init
Nov 24 17:11:13 cyberwinnie kernel: =================> NIC version : C-cut
Nov 24 17:11:13 cyberwinnie kernel: ===>rtl8192_SetWirelessMode(), wireless_mode:0x10, support_mode:0x16
Nov 24 17:11:13 cyberwinnie kernel: <===rtl8192_SetWirelessMode(), wireless_mode:10, bEnableHT = 1
Nov 24 17:11:17 cyberwinnie kernel: ====================>haha:IPSEnter()
Nov 24 17:11:17 cyberwinnie kernel: =========>NicIFDisableNIC()
Nov 24 17:11:17 cyberwinnie kernel: PHY_SetRtl8192seRfHalt save BB/RF
Nov 24 17:11:21 cyberwinnie kernel: eth0: no IPv6 routers present
Nov 24 17:11:22 cyberwinnie kernel: fuse init (API version 7.12)
Nov 24 17:11:26 cyberwinnie kernel: =========>r8192_wx_set_scan(): IPSLeave
Nov 24 17:11:26 cyberwinnie kernel: ===========>NicIFEnableNIC()
Nov 24 17:11:26 cyberwinnie kernel: gen_RefreshLedState first init
Nov 24 17:11:26 cyberwinnie kernel: =================> NIC version : C-cut
Nov 24 17:11:27 cyberwinnie kernel: ===>rtl8192_SetWirelessMode(), wireless_mode:0x10, support_mode:0x16
Nov 24 17:11:27 cyberwinnie kernel: <===rtl8192_SetWirelessMode(), wireless_mode:10, bEnableHT = 1
Nov 24 17:11:28 cyberwinnie kernel: Linking with Canvas,channel:7, qos:1, myHT:1, networkHT:0, mode:6 cur_net.flags:0x40e
Nov 24 17:11:28 cyberwinnie kernel: ===>ieee80211_associate_procedure_wq(), chan:7
Nov 24 17:11:28 cyberwinnie kernel: ==========>HTSetConnectBwMode():pHTInfo->bCurBW40MHz:0
Nov 24 17:11:28 cyberwinnie kernel: =================>ieee80211_authentication_req():auth->algorithm is 0
Nov 24 17:11:28 cyberwinnie kernel: Linking with Canvas,channel:7, qos:1, myHT:1, networkHT:0, mode:6 cur_net.flags:0x40e
Nov 24 17:11:28 cyberwinnie kernel: ===>ieee80211_associate_procedure_wq(), chan:7
Nov 24 17:11:28 cyberwinnie kernel: ==========>HTSetConnectBwMode():pHTInfo->bCurBW40MHz:0
Nov 24 17:11:28 cyberwinnie kernel: =================>ieee80211_authentication_req():auth->algorithm is 0
Nov 24 17:11:28 cyberwinnie kernel: ===>rtl8192_SetWirelessMode(), wireless_mode:0x6, support_mode:0x16
Nov 24 17:11:28 cyberwinnie kernel: <===rtl8192_SetWirelessMode(), wireless_mode:4, bEnableHT = 0
Nov 24 17:11:28 cyberwinnie kernel: #################ieee80211_sta_send_associnfo(), assocreq_ies_len:57,assocresp_ies_len:42
Nov 24 17:11:28 cyberwinnie kernel: ===>u4bAcParam:a425, ===>u4bAcParam:a449, ===>u4bAcParam:5e431c, ===>u4bAcParam:2f321c,
Nov 24 17:11:28 cyberwinnie kernel: Associated successfully
Nov 24 17:11:28 cyberwinnie kernel: ============>normal associate
Nov 24 17:11:28 cyberwinnie kernel: Using G rates:108
Nov 24 17:11:28 cyberwinnie kernel: Successfully associated, ht not enabled(0, 0)
Nov 24 17:11:28 cyberwinnie kernel: ===========rtl8192se_update_ratr_table: ff5
Nov 24 17:11:28 cyberwinnie kernel: ===>set to B/G mode
Nov 24 17:11:28 cyberwinnie kernel: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
Nov 24 17:11:28 cyberwinnie kernel: EAPOL TranslateHeader(), pTcb->DataRate = 0x2
Nov 24 17:11:28 cyberwinnie kernel: EAPOL TranslateHeader(), pTcb->DataRate = 0x2
Nov 24 17:11:28 cyberwinnie kernel: alg name:TKIP
Nov 24 17:11:28 cyberwinnie kernel: rtl819xSE:EnableHWSecurityConfig8192:, hwsec:1, pairwise_key:2, SECR_value:c
Nov 24 17:11:28 cyberwinnie kernel:
Nov 24 17:11:28 cyberwinnie kernel: rtl819xSE:====>to setKey(), dev:ffff88013c090000, EntryNo:4, KeyIndex:0, KeyType:2, MacAddr00:04:0e:db:8b:da
Nov 24 17:11:28 cyberwinnie kernel:
Nov 24 17:11:28 cyberwinnie kernel: rtl819xSE:=========>after set key, usconfig:8008
Nov 24 17:11:28 cyberwinnie kernel:
Nov 24 17:11:29 cyberwinnie kernel: ========>dm_check_edca_turbo():iot peer is unknown, bssid:00:04:0e:db:8b:da
Nov 24 17:11:30 cyberwinnie kernel: alg name:TKIP
Nov 24 17:11:30 cyberwinnie kernel: rtl819xSE:====>to setKey(), dev:ffff88013c090000, EntryNo:2, KeyIndex:2, KeyType:2, MacAddrff:ff:ff:ff:ff:ff
Nov 24 17:11:30 cyberwinnie kernel:
Nov 24 17:11:30 cyberwinnie kernel: rtl819xSE:=========>after set key, usconfig:800a
Nov 24 17:11:30 cyberwinnie kernel:
Nov 24 17:11:30 cyberwinnie kernel: EAPOL TranslateHeader(), pTcb->DataRate = 0x2
Nov 24 17:11:30 cyberwinnie kernel: ===>DHCP Protocol start tx DHCP pkt src port:68, dest port:67!!
Nov 24 17:11:39 cyberwinnie kernel: wlan0: no IPv6 routers present
Nov 24 17:11:48 cyberwinnie kernel: rtl819xSE:==========>rtl8192_down()
Nov 24 17:11:48 cyberwinnie kernel:
Nov 24 17:11:48 cyberwinnie kernel: ################>notify_wx_assoc_event_rsl(): Tell user space disconnected
Nov 24 17:11:48 cyberwinnie kernel: Save max pwr
Nov 24 17:11:48 cyberwinnie kernel: rtl819xSE:<==========rtl8192_down()
Nov 24 17:11:48 cyberwinnie kernel:
Nov 24 17:11:48 cyberwinnie kernel: ============>r8192_wx_set_essid():driver is not up return
Nov 24 17:15:17 cyberwinnie kernel: usb 2-2.4: new high speed USB device using ehci_hcd and address 5
Nov 24 17:15:17 cyberwinnie kernel: usb 2-2.4: configuration #1 chosen from 1 choice
Nov 24 17:15:17 cyberwinnie kernel: Initializing USB Mass Storage driver...
Nov 24 17:15:17 cyberwinnie kernel: scsi6 : SCSI emulation for USB Mass Storage devices
Nov 24 17:15:17 cyberwinnie kernel: usb-storage: device found at 5
Nov 24 17:15:17 cyberwinnie kernel: usb-storage: waiting for device to settle before scanning
Nov 24 17:15:17 cyberwinnie kernel: usbcore: registered new interface driver usb-storage
Nov 24 17:15:17 cyberwinnie kernel: USB Mass Storage support registered.
Nov 24 17:15:22 cyberwinnie kernel: scsi 6:0:0:0: Direct-Access TOSHIBA USB 3.5"-HDD 100 PQ: 0 ANSI: 2
Nov 24 17:15:22 cyberwinnie kernel: sd 6:0:0:0: Attached scsi generic sg2 type 0
Nov 24 17:15:22 cyberwinnie kernel: usb-storage: device scan complete
Nov 24 17:15:22 cyberwinnie kernel: sd 6:0:0:0: [sdb] 1953525168 512-byte logical blocks: (1.00 TB/931 GiB)
Nov 24 17:15:22 cyberwinnie kernel: sd 6:0:0:0: [sdb] Write Protect is off
Nov 24 17:15:22 cyberwinnie kernel: sd 6:0:0:0: [sdb] Mode Sense: 38 00 00 00
Nov 24 17:15:22 cyberwinnie kernel: sd 6:0:0:0: [sdb] Assuming drive cache: write through
Nov 24 17:15:22 cyberwinnie kernel: sd 6:0:0:0: [sdb] Assuming drive cache: write through
Nov 24 17:15:22 cyberwinnie kernel: sdb: sdb1
Nov 24 17:15:22 cyberwinnie kernel: sd 6:0:0:0: [sdb] Assuming drive cache: write through
Nov 24 17:15:22 cyberwinnie kernel: sd 6:0:0:0: [sdb] Attached SCSI disk
rc.conf
# /etc/rc.conf - Main Configuration for Arch Linux
# LOCALIZATION
# LOCALE: available languages can be listed with the 'locale -a' command
# HARDWARECLOCK: set to "UTC" or "localtime"
# USEDIRECTISA: use direct I/O requests instead of /dev/rtc for hwclock
# TIMEZONE: timezones are found in /usr/share/zoneinfo
# KEYMAP: keymaps are found in /usr/share/kbd/keymaps
# CONSOLEFONT: found in /usr/share/kbd/consolefonts (only needed for non-US)
# CONSOLEMAP: found in /usr/share/kbd/consoletrans
# USECOLOR: use ANSI color sequences in startup messages
LOCALE="de_DE.utf8"
HARDWARECLOCK="UTC"
USEDIRECTISA="no"
TIMEZONE="Europe/Berlin"
KEYMAP="de-latin1"
CONSOLEFONT=
CONSOLEMAP=
USECOLOR="yes"
# HARDWARE
# MOD_AUTOLOAD: Allow autoloading of modules at boot and when needed
# MOD_BLACKLIST: Prevent udev from loading these modules
# MODULES: Modules to load at boot-up. Prefix with a ! to blacklist.
# NOTE: Use of 'MOD_BLACKLIST' is deprecated. Please use ! in the MODULES array.
MOD_AUTOLOAD="yes"
#MOD_BLACKLIST=() #deprecated
MODULES=()
# Scan for LVM volume groups at startup, required if you use LVM
USELVM="no"
# NETWORKING
# HOSTNAME: Hostname of machine. Should also be put in /etc/hosts
HOSTNAME="cyberwinnie"
# Use 'ifconfig -a' or 'ls /sys/class/net/' to see all available interfaces.
# Interfaces to start at boot-up (in this order)
# Declare each interface then list in INTERFACES
# - prefix an entry in INTERFACES with a ! to disable it
# - no hyphens in your interface names - Bash doesn't like it
# DHCP: Set your interface to "dhcp" (eth0="dhcp")
# Wireless: See network profiles below
#Static IP example
#eth0="eth0 192.168.0.2 netmask 255.255.255.0 broadcast 192.168.0.255"
eth0="dhcp"
INTERFACES=(eth0)
# Routes to start at boot-up (in this order)
# Declare each route then list in ROUTES
# - prefix an entry in ROUTES with a ! to disable it
gateway="default gw 192.168.0.1"
ROUTES=(!gateway)
# Enable these network profiles at boot-up. These are only useful
# if you happen to need multiple network configurations (ie, laptop users)
# - set to 'menu' to present a menu during boot-up (dialog package required)
# - prefix an entry with a ! to disable it
# Network profiles are found in /etc/network.d
# This now requires the netcfg package
#NETWORKS=(main)
# DAEMONS
# Daemons to start at boot-up (in this order)
# - prefix a daemon with a ! to disable it
# - prefix a daemon with a @ to start it up in the background
DAEMONS=(syslog-ng !network netfs crond alsa hal fam networkmanager gdm)

I'm sorry, it works at all 32bit distros. It's just the 64x thing..., which doesn't work.

Similar Messages

Windows recognizes iPod, but not iTunes or iPod updater, causes freezing

I'm having some issues with my 60GB iPod Photo. I tried to store my friend's music on my iPod as files. Upon uploading them to my own computer, some files caused freezing, requiring me to disconnect and reconnect the iPod. I finally gave up and deleted all the files stored on my iPod. All of a sudden, although Windows XP Pro recognized that an iPod was plugged in, it would no longer open iTunes automatically. When opening iTunes once the iPod was plugged in, it would cause iTunes to freeze.
I decided to restore my iPod. About halfway through, there was an error message saying my iPod could not be restored. All songs were deleted but my iPod was still not recognized. Now, the iPod updater does not recognize that in iPod is connected, even though Windows does. The updater freezes, inhibiting me from completing my restore. iTunes freezes as well when my iPod is plugged in. My iPod displays "update in progress - do not disconnect," but nothing happens. When my iPod is not connected to the computer, I can navigate through it normally, although it does need to be unfrozen when left unused for a couple of days. I cannot tell if it plays files because they were all removed during my unsuccessful restore.
I have tried reinstalling all my iPod related software and I have tried my iPod on more than one computer with different USB cables, but nothing works.
Help, please!

This is exactly the same problem that I am having I have posted on 14th March on itunes forum. I wish you luck I wait with interest to see what someone says. My ipod was working like a dream until i downloaded the update

Supplied memory card causing freezing???

Hi all,
Right i've had my E72 since oct 10 and during that time i've had a few accounts of freezing when ending applications etc but nothing major. Also i was having the access point menu randomly flashing up. I noticed these issues more (the access point menu entirley) after i updated the software. I was also noticing the keypad not lighting up everytime i used it, it would come on half way through a text.
I took the phone to my local express repair center where they simply hard reset the phone although im not sure if they did anything to the keypad/light sensor. Since getting the phone back its freezing worse than before and the keypad seems to be no better. Through looking on here i've found that memory cards can cause freezing and i've recently swapped my old samsung one for the one supplied with the phone. I also didn't realise about the light sensor (dumb*** ) but the keypad has been unlit in the dark before!
Are the supplied memory cards just bad or is it the handset and has anyone else had issues with there keypad light?
Many Thanks

I have an E73 and no issues with the light sensor...I think. Concerning the supplied memory card, have you tried reformatting it? I recently had a problem with one of my purchased 8 GB cards slowing down. I use the cards for file storage only: pictures, music, podcasts, etc. Saving or deleting files on the card took a very long time, and the application appeared to lock up for roughly 20 (?) seconds with no progress bar. Examining the card with a program like Windows' chkdsk revealed several errors on that chkdsk ultimately couldn't fix. So I backed up all the data, reformatted the card, copied the data back, and it's been working perfectly since. Just like hard drives and other storage, memory cards can fail, but that doesn't necessarily mean they're beyond saving.
On the other hand, I'm sure you've seen threads here about faulty phones. If the phone itself can fail, then the memory card can, too. You never know. Hope that helps.

Safari 6 causing freeze to OSX

Since i upgraded to Mountain Lion and Safari got upgraded too to 6, I started getting this issue especially when i play flash games on facebook or watching a video on youtube, i guess it's related to flash player i don't know. It starts ok and starts the flash content normally but 5 minutes later it freezes and causes freeze to the whole system i can't do anything unless i hit option+command+esc to force quite safari, once i shut it down the system starts working normally like charm! .. I have 2011 15" macbook pro.
I made some reserch on the internet about this issue and all i found is just "reset safari" and deleting some extensions or stuff and that never worked for me!
I check for any updates for flash player or safari almost everyday hoping to get rid of this problem.
btw, I'm using Firefox and it works normally with flash contents and youtube.

Uninstall the currently installed Flash plugin (required for both YouTube and Facebook) then reinstall new.
Uninstall > Troubleshoot Flash Player | Mac OS
Very important to uninstall the old plugin first.
Then reinstall new > http://get.adobe.com/flashplayer/?promoid=JZEFT
Then open System Preferences > Flash Player then select the Advanced tab.
Click: Delete All
Quit and relaunch Safari.
From the Safari menu bar click Safari > Reset Safari
Select: Clear History (also empties the cache)
Deselect the remaining boxes then click Reset.
Try a video.

Can the battery cause freeze ups/ beach balls?

Hello all,
Recently bought a newertech batt replacement that I saw referenced on here and at first all was good. After a day or so though the computer would lock up with browser open and not come back from sleep. The cursor would disappear.
I am wondering if the battery could cause this since it occurred occasionally after it went to sleep (Screensaver)? Perhaps I didn't calibrate the battery correctly?
I did a hardware test with the disk that comes with ibook and all parts passed including new hard drive, although disk permissions won't repair - gets stuck.
thanks,
Al

There may be some other hardware issues at play in
your computer; a new battery if properly calibrated
and the other aspects of the general system are good,
the machine should work.
Have you tried starting the computer in SafeBoot,
then try Disk Utility's 'repair disk permissions'
and then restart normally? Also, if you can't get
'disk permissions' to work, boot from the installer
disc and use that Disk Utility; also 'repair disk.'
Have you used a widget to see if the battery specs
are in the good range, and if it is getting charged
when other indications say that it is? iStat is a good
one. Also Sys Profiler can tell you a thing or two.
A proper reset of the PMU may help, if the issue
is related to charging, power, battery life, etc.
A too full hard disk drive with inadequate free space
for the system to function, and inadequate space for
virtual memory, could cause freeze-ups hangs and
other issues. This would be more likely & critical.
Look into Activity Monitor and see how all things
stack up. Free space vs full space; RAM vs demand;
virtual memory, CPU use, network activity, etc.
You replaced the hard disk drive? Damaged a cable?
Could be if there are read-write errors, the ATA
controller chip on the logicboard may be suspect.
Preventative maintenance and general housekeeping
are like troubleshooting in advance; since you know
the last time several recommended things were done.
How many places did you ask the same questions, btw?
Good luck & happy computing!
edited.

Specific E-mail with links causing freeze using Mail

My wife is getting newsletter style e-mail from Better Homes and Gardens that contain links to pictures and other websites. These pictures only appear if internet access is connected so I believe that they are links that only are active once the mail is selected. If the internet is off, the space for the photos is blank.
I have isolated the problem to these specific e-mail messages that once selected, start some process of internet activity that causes the entire system to freeze and I get the beachball. If I don't click on the message, everything is fine. If I then turn off the internet access and open that message I can read it but there are no pictures or links. And the system continues to work fine. If I leave the internet on and click on the message, it opens with the links and I can see pictures etc., BUT as I continue to read the message the computer will freeze up within 20 seconds. If I try to click on any links within the message the computer freezes almost instantly. Also, if I quickly get out of the message and try to view a different message from any other sender that also contains links, all the links and photos become unavailable. And within a couple seconds the computer is locked up.
From watching my internet access speed monitor and listening to the hard drive it appears that the message is initiating some internet access or hard drive activity that interupts other mail functions and locks up the machine.
Anyone know how to troubleshoot this further? Does it help to look at the message in it's raw coded form? What would I look for?
Thanks,
Curtis

You know, I expected an answer like; "Your parental control can't be used like that. Its just a program, so it will try to block adult sites, or block unsecure connections. Like AOL mail for example. If you want her to access the school mail, then you'll just have to allow unrestricted access to the web. You can still monitor her web browsing. As for gmail, some email sites are able to be accessed even with the parental controls turned on."
I even expected some arrogant replies like Carolyn's. Telling me how to access gmail.
Thanks for nothing!
Message was edited by: TMcClain

Clearing cache and cookies causes freeze

Every time I try to clear my cache or cookies, the systems freezes and crashes on me. This happens on different machines and in different locations. I'm on a MAC. The spinning wheel continues for 20 minutes, I have to force quit and reboot, and I find Why doesn't this ever work? here is the info I found: Please advise soonest.
<pre><nowiki>Application Basics
Name
Firefox
Version
16.0.2
User Agent
Mozilla/5.0 (Macintosh; Intel Mac OS X 10.5; rv:16.0) Gecko/20100101 Firefox/16.0
Profile Folder
Show in Finder
Enabled Plugins
about:plugins
Build Configuration
about:buildconfig
Crash Reports
about:crashes
Memory Use
about:memory
Extensions
Name
Version
Enabled
ID
Firefox Hotfix
20121019.01
false
[email protected]
Important Modified Preferences
Name
Value
browser.cache.disk.capacity
1048576
browser.cache.disk.smart_size.first_run
false
browser.cache.disk.smart_size_cached_value
1048576
browser.history_expire_days.mirror
180
browser.places.smartBookmarksVersion
4
browser.startup.homepage_override.buildID
20121024073032
browser.startup.homepage_override.mstone
16.0.2
extensions.lastAppVersion
16.0.2
network.cookie.prefsMigrated
true
places.database.lastMaintenance
1362757524
places.history.expiration.transient_current_max_pages
53688
places.last_vacuum
1334585658
print.macosx.pagesetup-2
PD94bWwgdmVyc2lvbj0iMS4wIiBlbmNvZGluZz0iVVRGLTgiPz4KPCFET0NUWVBFIHBsaXN0IFBVQkxJQyAiLS8vQXBwbGUvL0RURCBQTElTVCAxLjAvL0VO…
privacy.cpd.offlineApps
true
privacy.cpd.sessions
false
privacy.cpd.siteSettings
true
privacy.sanitize.migrateFx3Prefs
true
privacy.sanitize.timeSpan
0
security.warn_viewing_mixed
false
Graphics
Vendor ID
0x10de
Device ID
0x 393
WebGL Renderer
Blocked for your operating system version.
GPU Accelerated Windows
0
AzureBackend
quartz
JavaScript
Incremental GC
1
Accessibility
Activated
0
Prevent Accessibility
0
Library Versions
Expected minimum version
Version in use
NSPR
4.9.2
4.9.2
NSS
3.13.6.0 Basic ECC
3.13.6.0 Basic ECC
NSS Util
3.13.6.0
3.13.6.0
NSS SSL
3.13.6.0 Basic ECC
3.13.6.0 Basic ECC
NSS S/MIME
3.13.6.0 Basic ECC
3.13.6.0 Basic ECC</nowiki></pre>

This problem can be caused by clearing the cookies via [https://support.mozilla.org/en-US/kb/remove-recent-browsing-search-and-download-history Remove recent browsing, search and download history].
*Firefox/Tools > Options > Privacy > Firefox will: "Use custom settings for history" > [X] Clear history when Firefox closes > Settings
*Firefox > History > Clear Recent History or Tools > Clear Recent History
The Reset Firefox feature can fix many issues by restoring Firefox to its factory default state while saving your essential information.
Note: ''This will cause you to lose any Extensions, Open websites, and some Preferences.''
To Reset Firefox do the following:
#Go to Firefox > Help > Troubleshooting Information.
#Click the "Reset Firefox" button.
#Firefox will close and reset. After Firefox is done, it will show a window with the information that is imported. Click Finish.
#Firefox will open with all factory defaults applied.
Further information can be found in the [[Reset Firefox – easily fix most problems]] article.
Did this fix your problems? Please report back to us!

500 GB Hitatchi Travelstar causes freezing

And I am not talking about temperature.
After installing the 500 Giger from Hitatchi in my 2008 MacBook Aluminum, the computer freezes every few minutes. The spinning beachball starts and it lasts for about 20 seconds.
Do you think this is caused by the Sudden Motion Sensor? Does the Hitatchi suffer from the same issues as the Seagate disks? Would it help to switch of the Sudden Motion Sensor?

I installed the same drive in my wifes 08 Unibody Macbook, and she has never experienced any problems with it. Is this a 7200 or 5400 RPM version? Just curious...
Her is the specs of the drive in profiler:
Model: Hitachi HTS545050B9A300
Revision: PB4OC60G
Serial Number: xxxxxxxxxxxxxxxxxxx
Native Command Queuing: Yes
Queue Depth: 32
Removable Media: No
Detachable Drive: No
BSD Name: disk0
Mac OS 9 Drivers: No
Partition Map Type: GPT (GUID Partition Table)
S.M.A.R.T. status: Verified
Volumes:
Users MacBook:
Capacity: 465.44 GB
Available: 191.62 GB
We've never disabled anything such as SMS.

What is causing freeze on video plybk?

i am trying to view the proj. rvr. pltf. and i would like to know what is causing the freeze on video plybk, is it in the programming and/or designing. if, corrected it will improve the presentation as well, quality. an inquiring mind would like to know; thank you and God bless
Edited by: kermitwilliams on Feb 25, 2011 10:56 PM

You likely have a problem with your optical card and your logic board. Try starting from your install disc and run
Disk Utility
   1. Insert the Mac OS X Install disc that came with your computer, then restart the computer while holding the C key.
   2. When your computer finishes starting up from the disc, choose Disk Utility from the Installer menu. (In Mac OS X 10.4 or later, you must select your language first.)
      Important: Do not click Continue in the first screen of the Installer. If you do, you must restart from the disc again to access Disk Utility.
   3. Click the First Aid tab.
   4. Click the disclosure triangle to the left of the hard drive icon to display the names of your hard disk volumes and partitions.
   5. Select your Mac OS X volume.
   6. Click Repair. Disk Utility checks and repairs the disk.
Please post back with results,

Smart Groups in Contacts OSX 10.8.2 causing Freeze

I am having a problem, similar to a few other threads from the old addressbook, but related to the latest Contacts app.
Previous discussions suggest problems with old smartlists causing crashes, this time it is the new Smart Groups.
This morning, I tried to add a Smart Group using the OSX 10.8.2 Contacts app, but upon hitting OK, the program froze.
Earlier suggested list of steps to remove the offending smartlist begins by exporting the contacts to a separate file. Since, at the moment, the contacts app is unable to load without freezing immediately, the option of exporting the contacts to a file is not available.
Alternate solutions suggested, involve deleting certain group related metadata - but I am unable to locate the files mentioned.
AddressBook-v22.abcddb and the smart group metadata file in ~/Library » Application Support » AddressBook » Metadata
How bout the simple solution of having a program where the Smart Groups simply work? If I create a smart group it should just work! Not result in the freezing of the app! OK now having said that...
Any suggestions for how to Eliminate Smart Groups - ideally without eliminating groups generally! (perhaps using third party apps to clean up the Smart Group mess?).
Thanks

I'll just add that I have one smart group that causes the beachball effect. Can't select or right click it to delete it without the hang happening.
It's my - "contacts that aren't assigned to any other group" group.
Will try to discover how to reset/remove a smart group.

File info - causes freeze up

I'm using CS5 12.0.4 on a Mac 10.6.8
When working on an image and then going to File Info it causes a freeze-up
A blank info window comes up and the application is frozen.
I have to force quit and lose unsaved work.
The first time I left it on overnight and it was in the same state in the morning.
Anyone else see this?

Which of the usual trouble-shooting routines (trashing prefs by keeping command-alt-shift pressed while starting Photoshop, 3rd party plug-ins deactivation, system maintenance like repairing permissions, purging PRAM, font validation, etc.) have you performed so far?

Gaussian blur and Colour Adjust Hue/Saturation cause freeze-up

After using PS Elements 9 for a year, it has started to give me problems, and I can't find a fix for it online. Choosing Gaussian Blur, or Color - Adjust Hue/Saturation causes PSE 9 to freeze up and stop responding. This just started today, and I'm baffled. Some of the other filters have stopped working, but they don't cause a freeze-up. I've done a disk clean and defrag, but I haven't done anything different to my computer in a long time. I can try to uninstall/reinstall, but I'd rather not if there's a simpler solution. I'm on a Toshiba Satelite Notebook, i5 processor, 64-Bit OS Windows Home Premium. I'd appreciate any insight into this issue.

The editor saved prefs often get corrupted. You may need to rebuild the editor preferences to resolve any conflicts.
Hold down the Ctrl+Shift+Alt keys and simultaneously click on the Edit button on the welcome screen. Release the three keys and look behind the welcome screen by closing it. Or hold down the keys whilst double clicking on PhotoshopElementsEditor.exe (in Program Files x86\Adobe)
You should see a pop up box with the words: Delete Adobe Photoshop Elements Settings File?
Click on Yes
Then wait whilst Elements rebuilds the preferences.

Brushes Still Cause Freeze Up

I posted last week about this same problem. I have 11k images in library, the image I'm working on is RAW and 11mb in size. Before making any other changes to the image I make a curves adjustment via curves brick and then click the gear symbol to brush it in and it appears to work fine. If then I make a highlight/shadow adjustment and attempt to brush in, AP3 freezes and I have to force quit. In AP3 preferences I have "new projects automatically generate previews" unchecked and "use embedded jpeg when possible" checked. Any ideas on just why this is happening?

Hi BGreg! Thanks for the Rember site. I ran the test on the RAM (1 pass.) It detected no problems. Card is Kingston/Micron 1GB PC2700 333MHZ 200 pin DDR SODIMM "guaranteed compatible."
I still suspect possible overheating caused by installing (2) 1GB cards under the steel cover. It gets pretty hot. I left this cover off overnight during the Rember test, and continue to leave it off (being careful.) Powerbook hasn't crashed so far.
I wonder if anyone has successfully run (2) 1GB cards in the 1.33 GHz G4PowerPC Powerbook 17 inch without it freezing up after running awhile? If so, did you install a 1GHz card from Apple or another vendor?
Wonder if Apple has itself discovered an overheating problem as it doesn't seem to offer 2GB with this model of Powerbook anymore?
Best regards,
Mike

All print functions cause freezing

Whenever I try to print to my HP OfficeJet 6310, my Mac freezes. If I go to System Preferences to examine the print settings, it also freezes. I tried uninstalling the print driver, but this also causes the Mac to freeze.
I recently enabled Google Cloud Printing in Chrome and wondered if this could be causing the problem since printing was working before I did this. I disabled it and restarted but am still having the same problem.
Any ideas? Thanks!

1974dawgs
Welcome to the HP Community Forum.
Printables can be managed / scheduled through your HP Connected Account.
The Safari browser, in particular, historically does not work to manage the HP Connected Account Printables.
Try installing a Browser OTHER than the Safari browser to manage your Printables from your iPad.
You might find some help here:
HP Mobile Printing
Click the Kudos Thumbs-Up to say Thank You!
And...Click Accept as Solution when my Answer provides a Fix or Workaround!
I am pleased to provide assistance on behalf of HP. I do not work for HP.
Kind Regards,
Dragon-Fur

CC configuration causes freezing and file system corruption

I have received no response for:
http://forums.adobe.com/message/6074118
It is a major issue, can I file an issue/fix request somehow?
Basically it appears that the default configuration when installing the complete product suite causes the OS (OSX Mavericks) to freeze unpredictably and render the system unusable unless shut down and rebooted. This may result in file system corruption and data loss requiring complete reinstall of OS and all products.
Some have mentioned 'drive' is causing this, but I am not familiar with that component and do not see any options to remove or disable such a product in CC.
I do not want any non-essential add-ons (like Bridge?) - just a reliable production configuration so I can get work done.
The risk of having the system 'locked up' or file system corrupted is unacceptable.
Thanks,
Mike

Hi mkrjf,
Please enable root account and try to use Photoshop and let me know if still the same behavior.
Root: http://support.apple.com/kb/PH14281
Regards,
Romit Sinha

Wlan rtl8191se causes freeze on arch64

Similar Messages

Maybe you are looking for