WLAN Security or Misconfiguration problem?? Please Help!

Hello Gurus,
I have a very strange problem and can use some direction on what exactly to do.
Our setup is a little bit over board I thought but it was cost affective. Our set up currently is we have 3 SSIDs being multi casted from 6 AP's (aironet 1200 series) they are being controlled by a Cisco 4400 series Wlan controller. 1 SSID is for our Cisco Wireless Phones, the Other Private, and Public for Patrons.
The Patron SSID uses a Raius Server to authenticate through a device called WAM (its a D-link hot spot gateway) that uses our production server to authenticate through. Patrons connect to the SSID, redirected to web page, put in Card information and password. The problem is that when they connect they will sometimes drop connection BUT most of the time what happens is they connect go to IE and it pulls up error page could not display. Also, some can connect and are fine. This has been driving me crazy and here is the big problems i have found. I brought up some software that i used with my company in the past to my new job called laptop analyzer pro. I ran a scan and checked the Wyse report and found that the error packets where to do with an association table being to full and the clients where being told that they are not allowed to connect due to the table association overflow. Later I found out that the WLAN controller is Web based so I logged into to there to find out some additional information. I checked the monitoring and there where reports of several rogues AP's and one happened to be one that I picked up with the analyzer that was actually a spoofer (MAC Address). I also checked the test on the Radios, you know the test that tells if they pass on the Load Profile and etc. Turns out that 4/6 of the AP's failed the Load Profile test???? We only do about 370+ patrons a month but this does not tell us how many times a single patron connects. Any ideas on what I need to do? If you need additoinal information let me know because our patron are taking the brunt of this and this is a free service we provide because we are a library. Thanks in Advance to any help.

Chadwick
This sounds like my old Laptop with built in wireless never worked reliably, plug in my Cisco or lucent card and it all worked. Finally got a new driver that worked for the builtin wireless and it finaly worked.
Had the same problem with a consumer AP and USB WIFI radio, did not work reliably until I updated both to latest software.
HTH
Bill

Similar Messages

I want to buy an in-app purchase but i don`t remember my security questions and i cant access my recovery email either, what can i do? i have 100$ on my account and cant use it because of that problem, please help URGENT

I want to buy an in-app purchase but i don`t remember my security questions and i cant access my recovery email either, what can i do? i have 100$ on my account and cant use it because of that problem, please help URGENT

If you have a rescue email address on your account then you can use that - follow steps 1 to 5 half-way down this page will give you a reset link on your account : http://support.apple.com/kb/HT5312
If you don't have a rescue email address (you won't be able to add one until you can answer your questions) then you will need to contact Support in your country to get the questions reset : http://support.apple.com/kb/HT5699

I am using firefox 3.6.17 i upgraded it to 4.1.but it does not work properly sometimes it opens every website and most of the time it does not work . so what is the problem please help . thank you

i am using firefox 3.6.17 i upgraded it to 4.1.but it does not work properly sometimes it opens every website and most of the time it does not work . so what is the problem please help . thank you

Did you check your security software (firewall)?
A possible cause is security software (firewall) that blocks or restricts Firefox or the plugin-container process without informing you, possibly after detecting changes (update) to the Firefox program.
Remove all rules for Firefox from the permissions list in the firewall and let your firewall ask again for permission to get full unrestricted access to internet for Firefox and the plugin-container process.
See:
* [[Server not found]]
* [[Firewalls]]

Hi guys i have an ipad 1 and when i plug it in to my macbook pro picasa opens up and show its name but when i open itunes i cant find the name, ive been working my head out to solve the problem please help me:(

hi guys i have an ipad 1 and when i plug it in to my macbook pro picasa opens up and show its name but when i open itunes i cant find the name, ive been working my head out to solve the problem please help me:(

Pay no attention to iinami, the amount of replies to people saying their handsets must have been jailbroken everytime iTunes throws out an error is tremendous. (Clearly you don't need to have any real knowledge to get to level 3 on these forums, let's hope apple's geniuses know a lot more than some of their customers.)
http://support.apple.com/kb/TS3694
Solution below.
Error 9
This error occurs when the device unexpectedly loses its USB connection with iTunes. This can occur if the device is manually disconnected during the restore process. This issue can be resolved by performing USB troubleshooting, using a different USB dock-connector cable, trying another USB port, restoring on another computer, or by eliminating conflicts from third-party security software.

My iphone is on recovery mode and i can´t turn on it, when i try to recover it from itunes i get: "unknown error (36), i´ve tried to do lot of things but i can´t solve my problem. please help!!

my iphone is on recovery mode and i can´t turn on it, when i try to recover it from itunes i get: unknown error (36), i´ve tried to do lot of things but i can´t solve my problem. please help!!

Hi, i had the same problem. Try to find the file "apple" or "itunes" don't know it anymore exactly. Ahm well you need to delet any information or just plug in your iphone into an other computer. important is that your iphone never has been pluged in this computer before. This was what i did, and it worked!

Problem Please help me.....Let me know the area to look for it I am a DBA..

Problem Please help me.....Let me know the area to look for it I am a DBA..Thanks in advance to let me know the cause and the area to look and fix it...
Server Error in '/' Application.
Problem with SAP/BAPI. SAP.Connector.RfcCommunicationException: Connect to message server failed Connect_PM MSHOST=prddb01.lamrc.com, R3NAME=PRD, GROUP=Prod HR PRD LOCATION CPIC (TCP/IP) on local host ERROR service 'sapmsPRD' unknown TIME Wed May 04 08:59:06 2005 RELEASE 620 COMPONENT NI (network interface) VERSION 36 RC -3 MODULE ninti.c LINE 428 DETAIL NiPServToNo SYSTEM CALL getservbyname COUNTER 1 at SAP.Connector.SAPConnection.ThrowRfcException(RFC_ERROR_INFO_EX rfcerrInfo, Encoding encoding, String languangeCode) at SAP.Connector.SAPConnection.Open() at SAP.Connector.SAPClient.RfcInvoke(String method, Object[] methodParamsIn) at SAP.Connector.SAPClient.SAPInvoke(String method, Object[] methodParamsIn) at SoftwareKeySAPG.SAPProxy1.Z_Bapi_Load_Kpi_Region(ZSOFT_KPI_REGIONS_MTable& Kpi_Regions, ZSOFT_PROD_TYPETable& Prod_Type) at SoftwareKeySAPG.SAPGSK.LoadKPIRegion(DataSet dsProduct)
Description: An unhandled exception occurred during the execution of the current web request. Please review the stack trace for more information about the error and where it originated in the code.
Exception Details: System.Web.Services.Protocols.SoapException: Problem with SAP/BAPI. SAP.Connector.RfcCommunicationException: Connect to message server failed Connect_PM MSHOST=prddb01.lamrc.com, R3NAME=PRD, GROUP=Prod HR PRD LOCATION CPIC (TCP/IP) on local host ERROR service 'sapmsPRD' unknown TIME Wed May 04 08:59:06 2005 RELEASE 620 COMPONENT NI (network interface) VERSION 36 RC -3 MODULE ninti.c LINE 428 DETAIL NiPServToNo SYSTEM CALL getservbyname COUNTER 1 at SAP.Connector.SAPConnection.ThrowRfcException(RFC_ERROR_INFO_EX rfcerrInfo, Encoding encoding, String languangeCode) at SAP.Connector.SAPConnection.Open() at SAP.Connector.SAPClient.RfcInvoke(String method, Object[] methodParamsIn) at SAP.Connector.SAPClient.SAPInvoke(String method, Object[] methodParamsIn) at SoftwareKeySAPG.SAPProxy1.Z_Bapi_Load_Kpi_Region(ZSOFT_KPI_REGIONS_MTable& Kpi_Regions, ZSOFT_PROD_TYPETable& Prod_Type) at SoftwareKeySAPG.SAPGSK.LoadKPIRegion(DataSet dsProduct)
Source Error:
An unhandled exception was generated during the execution of the current web request. Information regarding the origin and location of the exception can be identified using the exception stack trace below.
Stack Trace:
[SoapException: Problem with SAP/BAPI.
SAP.Connector.RfcCommunicationException: Connect to message server failed
Connect_PM MSHOST=prddb01.lamrc.com, R3NAME=PRD, GROUP=Prod HR PRD
LOCATION    CPIC (TCP/IP) on local host
ERROR       service 'sapmsPRD' unknown
TIME        Wed May 04 08:59:06 2005
RELEASE     620
COMPONENT   NI (network interface)
VERSION     36
RC          -3
MODULE      ninti.c
LINE        428
DETAIL      NiPServToNo
SYSTEM CALL getservbyname
COUNTER     1
   at SAP.Connector.SAPConnection.ThrowRfcException(RFC_ERROR_INFO_EX rfcerrInfo, Encoding encoding, String languangeCode)
   at SAP.Connector.SAPConnection.Open()
   at SAP.Connector.SAPClient.RfcInvoke(String method, Object[] methodParamsIn)
   at SAP.Connector.SAPClient.SAPInvoke(String method, Object[] methodParamsIn)
   at SoftwareKeySAPG.SAPProxy1.Z_Bapi_Load_Kpi_Region(ZSOFT_KPI_REGIONS_MTable& Kpi_Regions, ZSOFT_PROD_TYPETable& Prod_Type)
   at SoftwareKeySAPG.SAPGSK.LoadKPIRegion(DataSet dsProduct)]
   System.Web.Services.Protocols.SoapHttpClientProtocol.ReadResponse(SoapClientMessage message, WebResponse response, Stream responseStream, Boolean asyncCall) +1503
   System.Web.Services.Protocols.SoapHttpClientProtocol.Invoke(String methodName, Object[] parameters) +218
   SoftwareKeyUI.InstalledBaseDataWS.InstalledBaseData.LoadKPIRegionMulti(DataSet products)
   SoftwareKeyUI.InstalledBaseDataAccess.LoadKPIRegionMulti(DataSet products)
   SoftwareKeyUI.InstalledBase.GetRegionDetails(Int32 userId, String product, String regionType)
   SoftwareKeyUI.FilteredAccess.GetRegionDetails(Int32 userId, String product, String regionType)
   SoftwareKeyUI.search.LoadRegionDetails()
   SoftwareKeyUI.search.regionType_SelectedIndexChanged(Object sender, EventArgs e)
   System.Web.UI.WebControls.ListControl.OnSelectedIndexChanged(EventArgs e) +108
   System.Web.UI.WebControls.DropDownList.System.Web.UI.IPostBackDataHandler.RaisePostDataChangedEvent() +26
   System.Web.UI.Page.RaiseChangedEvents() +115
   System.Web.UI.Page.ProcessRequestMain() +1099

The error is a very basic one - the sapmsPRD service is not known. You will have to go to <NT_ROOT>\system32\drivers\etc and add the entry sapmsPRD 3600 to this file.
This is basically telling the requester at what port to look for the message server.
C

Problem Please help me.....Let me know the area to look for it

Problem Please help me.....Let me know the area to look for it I am a DBA..Thanks in advance to let me know the cause and the area to look and fix it...
Server Error in '/' Application.
Problem with SAP/BAPI. SAP.Connector.RfcCommunicationException: Connect to message server failed Connect_PM MSHOST=prddb01.lamrc.com, R3NAME=PRD, GROUP=Prod HR PRD LOCATION CPIC (TCP/IP) on local host ERROR service 'sapmsPRD' unknown TIME Wed May 04 08:59:06 2005 RELEASE 620 COMPONENT NI (network interface) VERSION 36 RC -3 MODULE ninti.c LINE 428 DETAIL NiPServToNo SYSTEM CALL getservbyname COUNTER 1 at SAP.Connector.SAPConnection.ThrowRfcException(RFC_ERROR_INFO_EX rfcerrInfo, Encoding encoding, String languangeCode) at SAP.Connector.SAPConnection.Open() at SAP.Connector.SAPClient.RfcInvoke(String method, Object[] methodParamsIn) at SAP.Connector.SAPClient.SAPInvoke(String method, Object[] methodParamsIn) at SoftwareKeySAPG.SAPProxy1.Z_Bapi_Load_Kpi_Region(ZSOFT_KPI_REGIONS_MTable& Kpi_Regions, ZSOFT_PROD_TYPETable& Prod_Type) at SoftwareKeySAPG.SAPGSK.LoadKPIRegion(DataSet dsProduct)
Description: An unhandled exception occurred during the execution of the current web request. Please review the stack trace for more information about the error and where it originated in the code.
Exception Details: System.Web.Services.Protocols.SoapException: Problem with SAP/BAPI. SAP.Connector.RfcCommunicationException: Connect to message server failed Connect_PM MSHOST=prddb01.lamrc.com, R3NAME=PRD, GROUP=Prod HR PRD LOCATION CPIC (TCP/IP) on local host ERROR service 'sapmsPRD' unknown TIME Wed May 04 08:59:06 2005 RELEASE 620 COMPONENT NI (network interface) VERSION 36 RC -3 MODULE ninti.c LINE 428 DETAIL NiPServToNo SYSTEM CALL getservbyname COUNTER 1 at SAP.Connector.SAPConnection.ThrowRfcException(RFC_ERROR_INFO_EX rfcerrInfo, Encoding encoding, String languangeCode) at SAP.Connector.SAPConnection.Open() at SAP.Connector.SAPClient.RfcInvoke(String method, Object[] methodParamsIn) at SAP.Connector.SAPClient.SAPInvoke(String method, Object[] methodParamsIn) at SoftwareKeySAPG.SAPProxy1.Z_Bapi_Load_Kpi_Region(ZSOFT_KPI_REGIONS_MTable& Kpi_Regions, ZSOFT_PROD_TYPETable& Prod_Type) at SoftwareKeySAPG.SAPGSK.LoadKPIRegion(DataSet dsProduct)
Source Error:
An unhandled exception was generated during the execution of the current web request. Information regarding the origin and location of the exception can be identified using the exception stack trace below.
Stack Trace:
[SoapException: Problem with SAP/BAPI.
SAP.Connector.RfcCommunicationException: Connect to message server failed
Connect_PM MSHOST=prddb01.lamrc.com, R3NAME=PRD, GROUP=Prod HR PRD
LOCATION CPIC (TCP/IP) on local host
ERROR service 'sapmsPRD' unknown
TIME Wed May 04 08:59:06 2005
RELEASE 620
COMPONENT NI (network interface)
VERSION 36
RC -3
MODULE ninti.c
LINE 428
DETAIL NiPServToNo
SYSTEM CALL getservbyname
COUNTER 1
at SAP.Connector.SAPConnection.ThrowRfcException(RFC_ERROR_INFO_EX rfcerrInfo, Encoding encoding, String languangeCode)
at SAP.Connector.SAPConnection.Open()
at SAP.Connector.SAPClient.RfcInvoke(String method, Object[] methodParamsIn)
at SAP.Connector.SAPClient.SAPInvoke(String method, Object[] methodParamsIn)
at SoftwareKeySAPG.SAPProxy1.Z_Bapi_Load_Kpi_Region(ZSOFT_KPI_REGIONS_MTable& Kpi_Regions, ZSOFT_PROD_TYPETable& Prod_Type)
at SoftwareKeySAPG.SAPGSK.LoadKPIRegion(DataSet dsProduct)]
System.Web.Services.Protocols.SoapHttpClientProtocol.ReadResponse(SoapClientMessage message, WebResponse response, Stream responseStream, Boolean asyncCall) +1503
System.Web.Services.Protocols.SoapHttpClientProtocol.Invoke(String methodName, Object[] parameters) +218
SoftwareKeyUI.InstalledBaseDataWS.InstalledBaseData.LoadKPIRegionMulti(DataSet products)
SoftwareKeyUI.InstalledBaseDataAccess.LoadKPIRegionMulti(DataSet products)
SoftwareKeyUI.InstalledBase.GetRegionDetails(Int32 userId, String product, String regionType)
SoftwareKeyUI.FilteredAccess.GetRegionDetails(Int32 userId, String product, String regionType)
SoftwareKeyUI.search.LoadRegionDetails()
SoftwareKeyUI.search.regionType_SelectedIndexChanged(Object sender, EventArgs e)
System.Web.UI.WebControls.ListControl.OnSelectedIndexChanged(EventArgs e) +108
System.Web.UI.WebControls.DropDownList.System.Web.UI.IPostBackDataHandler.RaisePostDataChangedEvent() +26
System.Web.UI.Page.RaiseChangedEvents() +115
System.Web.UI.Page.ProcessRequestMain() +1099

Hi
You should make a mapping for the service sapmsPRD in your /etc/services file (On Windows: C:WINDOWSSYSTEM32DRIVERSETCservices). If your instance number is 00 you will have to add the following entry:
sapmsPRD 3600/tcp
Good luck!
René van Es

[TV@Master] Problem please help

I have Msi.mother board PT8-Neo -LSR , Model No.Ms-6799 , main board bios -Phonenix ,maind board version i updat it to 2.2 , cpu size 2.4 G celleron D/256/533 , memory size 256DDram (400),display card Nvidia Riva TNT2 model 64
the problem that i face it when i put my TV@nywhere -master card ,the pc stop at the main page that show the biso version and name of bios company and the letters do not bost well it look like a virus work , and when i take tha card off the pc go normally , i tried put it to other PCI the same problem
please help

i meany by fix the problem of getting the pc go on to windows with card on PCI salot but i still have the broblem of the driver
please read my reply again
my operating system is win me and i have also another pc have XP
when i log in to windows the system show that found my TV@nywhere card but it didnt took the installatin driver for it i tried to install the driver directly
but it give me this 2 mesages when i try to install the driver
MSI TV card is not found ,stop the installation
the other message is
MSI pvs driver installatin failed
i download the driver from msi page also give me the same messages
for known on Device Manager it show me that the driver there but do not have the driver and the ? mark beside them
what to do now

I'm in trouble, my iPod Touch is giving 4th shock when recharge and the battery does not last any more. who knows or has a similar problem, please help me. Note: all this after I downloaded the new version OS5.

I'm in trouble, my iPod Touch is giving 4th shock when recharge and the battery does not last any more. who knows or has a similar problem, please help me. Note: all this after I downloaded the new version OS5.

I would make an appointment at the Genius Bar of an Apple store because of the shock issue. I doubt it was caused by the update.

HT5312 I do not remember the security answer apple ID.Please help.Thanks you!

I do not remember the security answer apple ID.Please help.Thanks you!

If you have a rescue email address (which is not the same thing as an alternate email address) set up on your account then steps 1 to 5 on the page that you posted from should let you reset them : go to https://appleid.apple.com/ and click 'Manage your Apple ID' on the right-hand side of that page and log into your account, then click on 'Password and Security' on the left-hand side of that page and on the right-hand side you should see an option to send security question reset info to your rescue email address.
If you don't have a rescue email address (you won't be able to add one until you can answer 2 of your questions) then you will need to contact iTunes Support / Apple to get the questions reset.
Contacting Apple about account security : http://support.apple.com/kb/HT5699
When they've been reset (and if you don't already have a rescue email address) you can then use the steps half-way down the page that you posted from to add a rescue email address for potential future use

My iphone 4 is acting like crap right i can't even restore it everytime i try to reboot it my iphone freezes at the apple logo it is ******* to the point where i just want to smash it how do i solve this problem please help?

my iphone 4 is acting like crap right i can't even restore it everytime i try to reboot it my iphone freezes at the apple logo it is ******* me off to the point where i just want to smash it how do i solve this problem please help?

Don't worry, just follow these steps to fix iPhone stuck on Apple logo
=> First of all Start your Computer and then connect with Internet connection, now Download the latest version of the iTunes application
=> Now install the iTunes application in your System and connect your Device with computer via Data cable
=> Now connect your Device with iTunes application and then Tab on summary option, see in the left side bar of iTunes
=> Now Select restore option from iTunes and then confirm the Restore Message for better results. After this unplug your Device and Restart it
I hope that will surely
Thank you...

Hello!i have problem to insttal potoshop cs6 this is,we've encountered the following issues.installer failed to initialize.this could be due to a missing file.please download adobe support advisor to detected the problem.please,help me

this is,we've encountered the following issues.
installer failed to initialize.this could be due to a missing file.please download adobe support advisor to detected the problem.
please,help me!

Hi there Mylenium, is there any way you can help me? My cs6 is doing all kinds weird things lately. The liquifying too stopped working completely, when I try to work with the actions, it starts flickering and changing opacity in color by itself. It starts flickering and is completely out of whack! I tried uninstalling and reinstalling and still no luck. I tried getting in touch with adobe and no luck with that neither! Is there anyway you might be able to help?

My iPad stop working suddenly i see black screen only pressing the home? and sleep button dose not solve the problem please help?

My iPad stop working suddenly i see black screen only pressing the home and sleep button dose not solve the problem please help ?

Frozen or unresponsive iPad
Resolve these most common issues:
    •    Display remains black or blank
    •    Touch screen not responding
    •    Application unexpectedly closes or freezes
http://www.apple.com/support/ipad/assistant/ipad/
iPad Frozen, not responding, how to fix
http://appletoolbox.com/2012/07/ipad-frozen-not-responding-how-to-fix/
iPad Frozen? How to Force Quit an App, Reset or Restart Your iPad
http://ipadacademy.com/2010/11/ipad-frozen-how-to-force-quit-an-app-reset-or-res tart-your-ipad
Black or Blank Screen on iPad or iPhone
http://appletoolbox.com/2012/10/black-or-blank-screen-on-ipad-or-iphone/
What to Do When Your iPad Won't Turn On
http://ipad.about.com/od/iPad_Troubleshooting/ss/What-To-Do-When-Your-Ipad-Wo-No t-Turn-On.htm
iOS: Not responding or does not turn on
http://support.apple.com/kb/TS3281
Home button not working or unresponsive, fix
http://appletoolbox.com/2013/04/home-button-not-working-or-unresponsive-fix/
Fixing an iPad Home Button
http://tinyurl.com/om6rd6u
iPad: Basic troubleshooting
http://support.apple.com/kb/TS3274
 Cheers, Tom

My Ipad 2 does not turn on when not plugged to electricity. Even when plugged to electricity, it constantly restarts/switches itself off. what is the problem, please help??

My Ipad 2 does not turn on when not plugged to electricity. Even when plugged to electricity, it constantly restarts/switches itself off. what is the problem, please help??

i plugged it and pressed the home button for a few seconds. the connect to itunes screen appeared and the moment i disconnect the cable from the electric plug, it switches off. when i connect the cable to the PC, nothing happens, its as if nothing has been done.

X-Fi Fatal1ty Plat1num Champion Ed. problem, please help!

9X-Fi Fatalty Platnum Champion Ed. problem, please help!? Hi there everyone,
So i have a X-Fi Fatalty Platnum Champion Ed. and a computer with Windows 7.
I've searched the web and i found many people saying that the card it's working and perfectly compatible so i would like to exclude this option as far as the problems that i'm having.
So, right out of the box i've placed the front panel in with the ribbon cable and the power connected to it, then i connected the other end of the ribbon cable and finally placed the card in one of the PCI slots i have free.
Now, when i start my PC, i don't hear any particolar "beep messages" but nothing will come on the screen, in few words my PC will not boot at all. I can hear the HDD spinning, everything sounds normal except for that "little" problem.
So, i re-did all the connections thinking that maybe i did something wrong, but following the instruction i did exactly as told. So i tried again to power up the computer and i've noticed that the X-Fi logo is lit up (red light) and.. I don't really know if that means something or it's just something aside that doesn't really matter.. But, what is it's The PCI card is broken or there's something else?
I did try to disable the sound card (integrated mobo sound) from the BIOS but that didn't change anything. I did try all the software options but this looks like more of an hardware problem (please correct me if i'm wrong and/or i've missed something).
There's something that popped up in my mind.. the PSU. I noticed that i have a 300W PSU (mm.. low, isn't it's)?and i was wondering if that's enough or i need a more powerful one.. and if that's may be the case for the PCI to not work at all causing all i've already explained above. I mean.. It seems like i've installed a dead peripheral and that's impeding the computer to start up..
I don't know.. I need clarification and help, PLEASE.
Thank you very much in advance!

Look at the beta thread sticked above but good luck waiting for a new driver. That beta driver has been there since January and although better than the normal driver it is still crap.
All the boot type issues are with the SSD but if you getting in game crashes etc... under windows 8 that is simply that the driver stinks.

WLAN Security or Misconfiguration problem?? Please Help!

Similar Messages

Maybe you are looking for