WLC 2100 series Guest LAN not found

Hi there
I am unable to configure Guest LAN as in this link
http://www.cisco.com/en/US/tech/tk722/tk809/technologies_configuration_example09186a00808ed026.shtml
because my Cisco WLC 2112 version 7.0.240.0 does not have the option for Guest LAN. Is Guest LAN supported for WLC 2100 series? Any workarounds or suggestions?
Thanks for your help
DIego

Diego,
Wired guest access is not supported on WLC2106.
Reference:
http://www.cisco.com/en/US/tech/tk722/tk809/technologies_configuration_example09186a00808ed026.shtml#configs
consider using a WISM, WLC4400, 3750 integrated WLC or a WLC5500

Similar Messages

WLC 2100 Series Rack Mount Option

I am having a tough time finding the rackmount kit for the 2100 series Wireless Lan Controllers. Will the ASA5505-RACK-MNT= work?

Hi David,
Yes, this is the correct part to use :) I am guessing the ASA 5505 and WLC 2100 must use the same chassis;
http://www.cisco.com/en/US/docs/security/asa/hw/maintenance/guide/procs.html#wp104420
Hope this helps!
Rob

Routed network using VRF and WLC Webaccess for Guest LAN

I have a guest lan that uses a seperate VRF on my network. That guest LAN needs to get services and access the internet via the WLC.
I cannot assign an IP address on the ingress port of the WLC which doesn't allow me to setup an IP-Helper or a next hop for traffic via the WLC. Since the ingress and egress are on different vlan's somehow i need to route the traffic to the egress.
Using the VRF doesn't allow me to create a route like "ip route VRF Guest 0.0.0.0 0.0.0.0 gig 1/5" or "ip route VRF Guest 0.0.0.0 0.0.0.0 vlan 5"
Any ideas?

Does the L3 interface on your router or L3 switch look anything like this?
interface Vlan119
description GUEST VLAN
ip vrf forwarding GUEST
ip address 172.16.254.2 255.255.252.0
ip helper-address 172.16.255.1
no ip redirects
no ip proxy-arp
glbp 119 ip 172.16.254.1
glbp 119 timers 2 7
glbp 119 priority 150
glbp 119 preempt delay minimum 600
glbp 119 authentication md5 key-string 7 1326431F1B1917232203
glbp 119 forwarder preempt delay minimum 3600
load-interval 30
end
This is an edited version of an L3 interface in a 6509 hosting a WiSM. The WiSM guest interface is in this subnet. The helper points to NAC. Clients in this subnet are NAT'd to public IPs when heading out to the Internet.

HP Photosmart 7510 series printer (Printer not found)

My HP Photosmart 7510 printer was operating normal. Then when I tried to scan to the computer I got the following "The HP Photosmart series was not found." Then I received the following "The device you are trying to access has generated an error; Please ensure that the device has been properly confiqured." All of the other functions of my printer are working normally. It prints from the computer, it FAXs correctly (both transmitting and receiving) and copies. I have not made a changes to the system. What must I do to get the scanning function back?

Hello there! Welcome to the forums @trebor-340-ste ,
I saw your post about the scanning issue you are facing with your Photosmart 7510 and would like to try and help out! I thank you for letting me know you can copy and print!
Could you please respond with which OS you are running and I will research this for you.
In the meantime, please try a power reset and ensure the printer is plugged in directly to the wall outlet, avoiding power bars and surge protectors. This ensures the printer is receiving full power and may help greatly. If you are connected wireless on ethernet, also unplug your router for a minute before starting up the printer and computer.
Press the Power button to turn on the product.
With the product turned on, disconnect the power cord from the rear of the product.
Unplug the power cord from the wall outlet.
Wait at least 15 seconds.
Plug the power cord back into the wall outlet.
Reconnect the power cord to the rear of the product.
If the product does not turn on by itself, press the Power button to turn it on.
Thank you
R a i n b o w 7000I work on behalf of HP
Click the “Kudos Thumbs Up" at the bottom of this post to say
“Thanks” for helping!
Click “Accept as Solution” if you feel my post solved your issue, it will help others find the solution!

HP Pavilion dv6500 Entertainment Notebook PC series Operating system not found

Hello to all how are you doing guys doing today I'm having a problem and need the help from the tech world. So i have a Hp Pavilion dv6500 cto notebook. I started it up and got a black screen stating "Operating System Not Found". I couldnt get into safe mode to recover back to a safe point, i was able to get into the bios system to do a memory and Hard drive test, my memory test came back as a Pass but my Hard drive came back as a fail and stated "Replace Hard Drive".
Now i went out bought a new WD 500GB 5400rpm hard drive for the laptop, i installed it and did a Hard Drive test to make sure it was good and the test came back as a Pass. Now i had this laptop for years since 2007 and it broke just a few months ago, i just got the new hard drive yestarday and was playing doctor last night. When i got the laptop as a gift i was only given a recovery disk which did boot up and gave me the install now option and repair computer option. I chose the install now option and it was starting to install but then got this error message "Windows cannot open the required file D:\Sources\Install.wim. Make sure all files required for installation are available, and restart the installation. Error code: 0x80070002." I read that you cant install windows from a recovery disk so now im back to square one.
So current status is I got a new hard drive that pass the bios test, memory test was a pass. I have no windows disk other then the windows vista recovery disk i tried but failed to install windows. I also tried a windows 7 disk from work but the disk wouldnt boot up came back with a message stating that disk couldnt be read there may be problem with the cd dvd drive or hard drive, but when i put in the windows vista recovery disk that boot up no problem. i just cant install window with it. So Im stuck with a black screen stating no operating system is not found. Note that i havent change the boot up line up back to hard drive to see if it would boot up the new hard drive but i dought it would change anything since its a brand new hard drive with nothing on it.
If someone could help me with step by step like how to get an operating system on my new hard drive. My wife has a laptop but with no cd drive so i would need instruction to boot get it on the usb. Hope i was helpful with my problem.

You have only tried questionable disks. You could order a recovery disk from HP but I am not even sure they still have Vista recovery disks. You could also buy a Windows 7 OEM disk and try that. it will cost you a bit but will be legal. What version of Vista is it? You can also try to find a Vista install disk and use the Key Code on the bottom of the laptop if it is still legible. Here is a link to downloadable .iso files you can use to make a Vista install disk that will activate with your Key Code:
http://downloadsnfix.blogspot.com/2012/08/microsoft-windows-vista-official-iso.html

Measure throughput on WLC 2100 series

I didn't see a command in the list but is it possible to capture netflow on the WLC port. I have configured 10 APs but the users are complaining about dropped connections during peak times and I'm trying to pin down the nature of the problem.
Thanks!
Tim

Yes. Configure netflow on the switchport the WLC is plugged into, if your switch supports it.

3000 j series network adapter not found

i recently downgraded to win xp from vista basic due to super poor performance. but xp isn't finding my network adapter. i was told to get drivers. so i came to this site and downloaded what i thought was the right network driver but still no adapter. i have been trying to get this computer online for 4 days now to no avail. please help
Solved!
Go to Solution.

http://www-307.ibm.com/pc/support/site.wss/MIGR-66153.html

LAP1142 can not join wlc 2100 !

I'd WLC 2100 series and 9 access point LAP1142N .
8 LAP1142N can work fine and join a capwap controller is ok but only one LAP1142 is can not .
Could you help me to solve it ? Part of LAP is AIR-LAP1142N-A-K9
Apr 2 10:52:42.284: LWAPP_CLIENT_EVENT: spamResolveStaticGateway - gateway found
*Apr 2 10:52:42.284: LWAPP_CLIENT_EVENT: spamResolveStaticGateway - gateway found
*Apr 2 10:52:42.284: LWAPP_CLIENT_EVENT: Dropping discovery in LWAPP. This AP model is not supported by LWAPP WLC.
*Apr 2 10:52:42.284: status of voice_diag_test from WLC is false
*Apr 2 10:52:52.284: %CAPWAP-3-ERRORLOG: Go join a capwap controller
*Apr 2 10:52:52.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 172.16.28.21 peer_port: 5246
*Apr 2 10:52:52.000: %CAPWAP-5-CHANGED: CAPWAP changed state to
*Apr 2 10:52:52.667: LWAPP_CLIENT_EVENT: lwapp_check_image_good: image is good now
*Apr 2 10:52:53.107: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 172.16.28.21 peer_port: 5246
*Apr 2 10:52:53.108: %CAPWAP-5-SENDJOIN: sending Join Request to 172.16.28.21
*Apr 2 10:52:53.108: %CAPWAP-5-CHANGED: CAPWAP changed state to JOIN
*Apr 2 10:52:53.198: LWAPP_CLIENT_EVENT: ap model AIR-LAP1142N-A-K9
*Apr 2 10:52:53.198: LWAPP_CLIENT_EVENT: ap sw version 12.4(23c)JA
*Apr 2 10:52:53.198: LWAPP_CLIENT_EVENT: lwapp_encode_ap_reset_button_payload: reset button state on
*Apr 2 10:52:53.237: %CAPWAP-5-CHANGED: CAPWAP changed state to CFG
*Apr 2 10:52:53.240: %DTLS-5-ALERT: Received WARNING : Close notify alert from 172.16.28.21
*Apr 2 10:52:53.240: %DTLS-5-PEER_DISCONNECT: Peer 172.16.28.21 has closed connection.
*Apr 2 10:52:53.241: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 172.16.28.21:5246
*Apr 2 10:52:53.279: LWAPP_CLIENT_EVENT: bsnDeleteAllMobiles radio 0
*Apr 2 10:52:53.279: LWAPP_CLIENT_EVENT: bsnLockDevice radio 0
*Apr 2 10:52:53.279: LWAPP_CLIENT_EVENT: bsnDeleteAllMobiles radio 1
*Apr 2 10:52:53.279: LWAPP_CLIENT_EVENT: bsnLockDevice radio 1
*Apr 2 10:52:53.280: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*Apr 2 10:52:53.280: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*Apr 2 10:52:53.286: LWAPP_CLIENT_EVENT: spamInitCfgData: Loaded configuration into v2 struct (version 7.0.98.0)

Actually, 5.2 or later is needed.
5.0 and 5.1 do not even support 1140 Access point.
Rating useful replies is more useful than saying "Thank you"

Diifference between WLC 2100 and 4400 and 5500

Hi
what is the difference between wire lan controllers(WLAN) 2100 and 4400 and 5500.

Hello syed
Cisco 5500 Series Controllers:
The Cisco 5500 Series Wireless LAN Controller is currently available in one model: 5508. The 5508 controller supports up to 250 lightweight access points and 7000 wireless clients (or 5000 wireless clients and 2500 RFID tags when using the client location feature), making it ideal for large enterprises and high-density applications.
Cisco 4400 Series Controllers:
Because the Cisco 4400 Series Wireless LAN Controller supports 802.11a/b/g and the IEEE 802.11n draft 2.0 standard, organizations can deploy the solution that best meets their individual requirements. Organizations can offer robust coverage with 802.11 a/b/g or deliver greater performance with 5x the throughput and unprecedented reliability using 802.11n and Cisco's Next-Generation Wireless Solutions and Cisco Enterprise Wireless Mesh.
The Cisco 4400 Series Wireless LAN Controller is available in two models. The Cisco 4402 Wireless LAN Controller with two 1 GB Ethernet ports comes in configurations that support 12, 25, and 50 access points. The Cisco 4404 Wireless LAN Controller with four 1 GB Ethernet ports supports 100 access points. The Cisco 4402 controller provides one expansion slot. The Cisco 4404 controller provides two expansion slots that can be used to add VPN termination.
Cisco 2100 Series Controllers:
These controllers are part of a Payment Card Industry (PCI) certified architecture, and are well suited for retail customers who deploy transactional data applications such as scanners and kiosks. With performance up to 100 Mbps, the Cisco 2100 Series Wireless LAN Controllers also enable small and medium branch offices to deploy collaboration applications such as guest access and mobile voice.

File not found error while trying to generate stub using wsdl2java

Hi
I am facing this peculiar problem while generating the stub thru the wsdl2java command.
It shows series of file not found exception.
What all thing need to be set or taken care while we execute the command . anybody having window script for doing this please share it with me.
Your help is higly appreciated
Thanks
Ottran

It could be that the wsdl file is not found if you are invoking this command for a wsdl which is locally existing
Could you send the command and the exception msgs that you are getting
Regards
Mari

CF 9.01 - jrun.exe SQLServerURLParser Path Not Found

I found a similar post about this from 2 years ago (http://forums.adobe.com/thread/920226) but it had no responses. I'm hoping someone sees this and has some ideas. The server in question is running CF 9.01 Enterprise in multiserver configuration in a cluster with hf901-00008.jar as the current patch level. all on Windows Server 2008 R2
We began having problems a couple of days ago where sites were unresponsive, restarting IIS seemed to be the only thing that fixed the issue. We also began seeing problems with application pools shutting off (or not starting when IIS was restarted)
Below is an exerpt from a Process Explorer log file, over the course of 45 minutes more than 1.4 MILLION of these errors are repeated.
"11:05:03.7878844 AM","jrun.exe","1996","QueryOpen","D:\JRun4\lib\macromedia\jdbc\sqlserver\SQLServerURLPar ser.class","PATH NOT FOUND",""
"11:05:03.7878824 AM","jrun.exe","1996","QueryOpen","D:\JRun4\classes\macromedia\jdbc\sqlserver\SQLServerUR LParser.class","PATH NOT FOUND",""
"11:05:03.7880570 AM","jrun.exe","1996","QueryOpen","D:\JRun4\macromedia\jdbc\sqlserver\SQLServerURLParser. class","PATH NOT FOUND",""
"11:05:03.7881455 AM","jrun.exe","1996","QueryOpen","D:\JRun4\servers\server1\macromedia\jdbc\sqlserver\SQL ServerURLParser.class","PATH NOT FOUND",""
"11:05:03.7882880 AM","jrun.exe","1996","QueryOpen","D:\JRun4\servers\server1\cfusion.ear\cfusion.war\macro media\jdbc\sqlserver\SQLServerURLParser.class","PATH NOT FOUND",""
"11:05:03.7884580 AM","jrun.exe","1996","QueryOpen","D:\JRun4\servers\server1\cfusion.ear\cfusion.war\WEB-I NF\classes\macromedia\jdbc\sqlserver\SQLServerURLParser.class","PATH NOT FOUND",""
"11:05:03.7907685 AM","jrun.exe","1996","QueryOpen","D:\JRun4\servers\server1\cfusion.ear\cfusion.war\WEB-I NF\cfusion\lib\macromedia\jdbc\sqlserver\SQLServerURLParser.class","PATH NOT FOUND",""
"11:05:03.7908994 AM","jrun.exe","1996","QueryOpen","D:\JRun4\servers\server1\cfusion.ear\cfusion.war\WEB-I NF\cfusion\gateway\lib\macromedia\jdbc\sqlserver\SQLServerURLParser.class","PATH NOT FOUND",""
"11:05:03.7910091 AM","jrun.exe","1996","QueryOpen","D:\JRun4\servers\server1\cfusion.ear\cfusion.war\WEB-I NF\flex\jars\macromedia\jdbc\sqlserver\SQLServerURLParser.class","PATH NOT FOUND",""
"11:05:03.7911502 AM","jrun.exe","1996","QueryOpen","D:\JRun4\servers\server1\cfusion.ear\cfusion.war\WEB-I NF\cfform\jars\macromedia\jdbc\sqlserver\SQLServerURLParser.class","PATH NOT FOUND",""
"11:05:03.7914672 AM","jrun.exe","1996","QueryOpen","D:\JRun4\servers\lib\macromedia\jdbc\sqlserver\SQLServ erURLParser.class","PATH NOT FOUND",""
"11:05:03.7916013 AM","jrun.exe","1996","QueryOpen","D:\JRun4\servers\cfusion\cfusion-ear\cfusion-war\WEB-I NF\cfusion\lib\oosdk\classes\macromedia\jdbc\sqlserver\SQLServerURLParser.class","PATH NOT FOUND",""
"11:05:03.7917110 AM","jrun.exe","1996","QueryOpen","D:\JRun4\servers\cfusion\cfusion-ear\cfusion-war\WEB-I NF\cfusion\lib\oosdk\lib\macromedia\jdbc\sqlserver\SQLServerURLParser.class","PATH NOT FOUND",""
"11:05:03.7918284 AM","jrun.exe","1996","QueryOpen","D:\JRun4\servers\cfusion\cfusion-ear\cfusion-war\WEB-I NF\cfusion\lib\lib\macromedia\jdbc\sqlserver\SQLServerURLParser.class","PATH NOT FOUND",""
"11:05:03.7919388 AM","jrun.exe","1996","QueryOpen","D:\JRun4\servers\cfusion\cfusion-ear\cfusion-war\WEB-I NF\cfusion\lib\oosdk\bin\macromedia\jdbc\sqlserver\SQLServerURLParser.class","PATH NOT FOUND",""
This seems excessive and a waste of processor cycles if this is part of the normal class loading process...

This behavior occurs only If I put a <cfapplication> tag on my cfm page.
When I put the <cfapplication> tag in an explicit file Application.cfm, cfc syntax error messages appears correctly.
Maybe just a problem with my configuration (IIS7), but perhaps an indication...

Guest LAN and DHCP Options not passing through

Managed to get the Guest LAN up and running for wired clients and all's working well. Users are sat behind a proxy and if I force the use of a appropriate wpad file I can get the WLC auth to happen and then push off to the proxy.
I'm trying to use option 252 in DHCP to present the WPAD url. Only issue that happens is that while the DHCP server on the egress interface is handing out addresses to clients on the ingress interface correctly, the WLC doesn't appear to be handing through the option 252 I have set in DHCP. I've used network monitor to see what the dhcp request process is dishing out in terms of options, and all look good if I'm not behind the WLC.
Anyone know if theres a limitation on the WLC that prevents DHCP options being passed through to the guest LAN?
TIA

When configured as a DHCP server, some of the firewalls do not support DHCP requests from a relay agent. The WLC is a relay agent for the client. The firewall configured as a DHCP server ignores these requests. Clients must be directly connected to the firewall and cannot send requests through another relay agent or router. The firewall can work as a simple DHCP server for internal hosts that are directly connected to it. This allows the firewall to maintain its table based on the MAC addresses that are directly connected and that it can see. This is why an attempt to assign addresses from a DHCP relay are not available and the packets are discarded. PIX Firewall has this limitation.
For more information please refer to the link-http://www.cisco.com/en/US/tech/tk722/tk809/technologies_configuration_example09186a008070ba8f.shtml

Switchports of wlc 2100 dont bridge to rest of the LAN

Hi,
I've configured several WLC's before but I'm new to the 2100 series. I'm a bit confused in the way the 8 ports function. I have the following setup:
2 AP's (1131AG)
3 clients's (wired)
All five connected to WLC on ports 8,7,6,5,4
WLC port 1 is connected to a 24 port switch, non Cisco, so no CDP info available (may that matter).
The whole network should be an untagged Vlan. This is also the way I've runned the basic setup. AP int + MGM int are both untagged configured on port 1.
So I would like the 8 ports to function as an "expansion" to the 24 port switch. But for some reason there is no traffic possible between the wired clients+ap's on the WLC and the rest of the network.
Both sides can ping the AP int + MGM int of the WLC.
DHCP proxy works as well, the AP's get their IP, the wired client's dont.
As soon as the AP tries to resolve CISCO-CAPWAP-CONTROLLER.domain.local it fails, when connected to the 24 port switch, it succeeds, because the DNS server is on that side.
Am I missing something here?
Thanks for your help!
Update: WLC is running the latest version7

The ports on the 2106 are designed to support AP connections or an uplink to a switch. They will not work with PC's connected to them.

Sqlldr: Message 2100 not found - No msg files in my RDBMS\Mesg dir

Hi All,
I am trying to use sqlldr on an WIN2003R3 server. This is not working and I get an error message:
MESSAGE 2100 NOT FOUND: WHEN ATTEMPTING TO START SQLLDR.
I searched the internet and there it states that this should have to do with my ORACLE_HOME or ORACLE_BASE environment variables or path. I checked those, but they seem fine.
On metalink it states two possiblities, for WIN NT,
- Removing the ORACLE_HOME env. variable
- Copy the files from another Oracle installation
(Metalink Note:171648.1 and Note:1081848.6).
I tried the first, but still doesnot work. Unfortunately I can't try the second, because all other Oracle installations I have access to are the same version, so they all have the same files in the RDBMS\Mesg directory.
My questions are:
- How many files should there be in the mentioned directory? (Now I've got 4: kgpus.msb, ocius.msb, oraus.msb, smgus.msb )
- Where can I get the missing files, or is there any other way to get around this?
- any ohter suggestions?
Thanks in advance. Any help will be appreciated,
Regards,
Toin.
Message was edited by:
Toin
Fixed a typo.
Message was edited by:
Toin

The problem is that my SQL Loader is not working under WIN NT. This is a known issue, one of the suggestions I found on metalink is to manually copy the message files that should be in ORACLE_HOME\DBMS\Mseg from another Oracle installation.
I cannot do this, because all my Oracle installations are the same. So the questions is where can I find the appropriate message files, so I can get my SQL Loader to run??
Thanks.
Toin.

"The HP Deskjet 3050 J610 series was not found." Can't scan with wireless printer to desktop. Help

Our new wireless printer will not scan. I have tried to scan from the computer and get the below error message and then I have activated the scan from printer and when I push the scan button on the printer, I get the same error message.
Thanks!
Product Name: HP Deskjet 3050 J610 Printer/Scanner/Copier
Operating System: Windows 7
Error Message: The HP Deskjet 3050 J610 series was not found - when trying to scan.
No changes made to system

I had some problem. I found you must use HP 'Update IP address' program to add printer instead use window add printer. All programs -> HP ->HP Deskjet 3050 610 series -> Update IP address.

WLC 2100 series Guest LAN not found

Similar Messages

Maybe you are looking for