WLC 2100 Series Rack Mount Option

I am having a tough time finding the rackmount kit for the 2100 series Wireless Lan Controllers. Will the ASA5505-RACK-MNT= work?

Hi David,
Yes, this is the correct part to use :) I am guessing the ASA 5505 and WLC 2100 must use the same chassis;
http://www.cisco.com/en/US/docs/security/asa/hw/maintenance/guide/procs.html#wp104420
Hope this helps!
Rob

Similar Messages

WLC 2100 series Guest LAN not found

Hi there
I am unable to configure Guest LAN as in this link
http://www.cisco.com/en/US/tech/tk722/tk809/technologies_configuration_example09186a00808ed026.shtml
because my Cisco WLC 2112 version 7.0.240.0 does not have the option for Guest LAN. Is Guest LAN supported for WLC 2100 series? Any workarounds or suggestions?
Thanks for your help
DIego

Diego,
Wired guest access is not supported on WLC2106.
Reference:
http://www.cisco.com/en/US/tech/tk722/tk809/technologies_configuration_example09186a00808ed026.shtml#configs
consider using a WISM, WLC4400, 3750 integrated WLC or a WLC5500

SF 300 Series rack mount brackets

I have misplaced the rack mount brackets for a SF 300-24P switch. I have searched online to try and find replacements. Anyone have a clue as to were I could find some?

Dave,
Please open a case with Cisco Support and they will be able to help you.
Thanks,
Ivor

Measure throughput on WLC 2100 series

I didn't see a command in the list but is it possible to capture netflow on the WLC port. I have configured 10 APs but the users are complaining about dropped connections during peak times and I'm trying to pin down the nature of the problem.
Thanks!
Tim

Yes. Configure netflow on the switchport the WLC is plugged into, if your switch supports it.

LAP1142 can not join wlc 2100 !

I'd WLC 2100 series and 9 access point LAP1142N .
8 LAP1142N can work fine and join a capwap controller is ok but only one LAP1142 is can not .
Could you help me to solve it ? Part of LAP is AIR-LAP1142N-A-K9
Apr 2 10:52:42.284: LWAPP_CLIENT_EVENT: spamResolveStaticGateway - gateway found
*Apr 2 10:52:42.284: LWAPP_CLIENT_EVENT: spamResolveStaticGateway - gateway found
*Apr 2 10:52:42.284: LWAPP_CLIENT_EVENT: Dropping discovery in LWAPP. This AP model is not supported by LWAPP WLC.
*Apr 2 10:52:42.284: status of voice_diag_test from WLC is false
*Apr 2 10:52:52.284: %CAPWAP-3-ERRORLOG: Go join a capwap controller
*Apr 2 10:52:52.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 172.16.28.21 peer_port: 5246
*Apr 2 10:52:52.000: %CAPWAP-5-CHANGED: CAPWAP changed state to
*Apr 2 10:52:52.667: LWAPP_CLIENT_EVENT: lwapp_check_image_good: image is good now
*Apr 2 10:52:53.107: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 172.16.28.21 peer_port: 5246
*Apr 2 10:52:53.108: %CAPWAP-5-SENDJOIN: sending Join Request to 172.16.28.21
*Apr 2 10:52:53.108: %CAPWAP-5-CHANGED: CAPWAP changed state to JOIN
*Apr 2 10:52:53.198: LWAPP_CLIENT_EVENT: ap model AIR-LAP1142N-A-K9
*Apr 2 10:52:53.198: LWAPP_CLIENT_EVENT: ap sw version 12.4(23c)JA
*Apr 2 10:52:53.198: LWAPP_CLIENT_EVENT: lwapp_encode_ap_reset_button_payload: reset button state on
*Apr 2 10:52:53.237: %CAPWAP-5-CHANGED: CAPWAP changed state to CFG
*Apr 2 10:52:53.240: %DTLS-5-ALERT: Received WARNING : Close notify alert from 172.16.28.21
*Apr 2 10:52:53.240: %DTLS-5-PEER_DISCONNECT: Peer 172.16.28.21 has closed connection.
*Apr 2 10:52:53.241: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 172.16.28.21:5246
*Apr 2 10:52:53.279: LWAPP_CLIENT_EVENT: bsnDeleteAllMobiles radio 0
*Apr 2 10:52:53.279: LWAPP_CLIENT_EVENT: bsnLockDevice radio 0
*Apr 2 10:52:53.279: LWAPP_CLIENT_EVENT: bsnDeleteAllMobiles radio 1
*Apr 2 10:52:53.279: LWAPP_CLIENT_EVENT: bsnLockDevice radio 1
*Apr 2 10:52:53.280: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*Apr 2 10:52:53.280: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*Apr 2 10:52:53.286: LWAPP_CLIENT_EVENT: spamInitCfgData: Loaded configuration into v2 struct (version 7.0.98.0)

Actually, 5.2 or later is needed.
5.0 and 5.1 do not even support 1140 Access point.
Rating useful replies is more useful than saying "Thank you"

Rack mount kit - WLC 2100

What's the Part Number for the Cisco WLC 2100 rack mount kit?
Thanks in advance.

Allows for convenient desktop mounting or rack mounting, with optional rack mount kit for flexible deployment.
http://www.cisco.com/en/US/products/ps7206/products_data_sheet0900aecd805aaab9.html

2100 rack mount

Does anyone have a part number for a 2100 rack mount kit, cant find it on Cisco anywhere? Is it the same as for the 526 the ACS-UC500RM-19=

Hi,
the Rack-Mount-Kit for the WLC-2100 is the same as the one for the ASA-5505. It's called ASA5505-RACK-MNT=.
Greets,
Sebastian

ASA5585 - which rack mount?

Sadly dissappointed in the documentation...
I would think that one of these parts would be the rack kit used when eliminating the slide rails to fit the 5585 in a narrow rack as described in the hardware installation guide ( http://www.cisco.com/c/en/us/td/docs/security/asa/hw/maintenance/5585guide/5585Xhw/procedures.html#79288 )
Rack-Mounting the Chassis Using the Fixed Rack Mount
If you are not able to use the slide rail kit in your rack installation, an optional fixed rack mount solution is available. You can install fixed front and rear rack mount brackets on the ASA 5585-X so that you can easily mount it in a rack.
OK, that is what I want, but what part is it? Is it one of the three below? Is it something else?
ASA5585-RAILS=
ASA 5585 Rail kit
ASA5585-REAR-RACK=
ASA 5585-X Rear Rack Mounts (1 pair)
ASA5585-RACK-KIT=
ASA 5585-X Front Rack and Rear Rack Kit
it used to be you could search for a datasheet, but those are now bloated with a bunch of marketing fluff that is not remotely close to being datasheets.

The RAILS part is the standard slide rail kit with the ball bearings etc. that allows the ASA to slide in and out without unmounting.
The REAR-RACK is the little guide pieces that attach to the ASA plus the longer bits that attach to the rack's rear posts to give the unit support on the rear. It's sold separately in case someone started out with the kit below but only used the front hardware and the rear bits went missing if/when they decided they should add them.
The RACK-KIT includes the REAR-RACK pieces plus the big rectangular pieces with ears that attach on the front sides of the ASA and allow you to secure it into your front posts.

WLC 2100 and DHCP strange issue.

Hi,
i have this scenario: 1 WLC 2100 and two LW AP 3500 connected. If the access points are connected via external switch evrything works well - AP and Clients get IP address from external DHCP and this is ok but when im connecting AP 3500 directly to one of ports on WLC i need to chceck in controller web Controller -> Advanced -> DHCP -> Enable DHCP proxy - after that AP get IP addres and clients get too but ip is assigned from external dhcp but the gateway is set as controller IP address (!!!) so clients not works. I want to configure access points connected directly do WLC.
I have small setup and i have configured all in the one vlan - management dla users are in the same vlan.
And the second is - for what usage is internal DHCP server - and how to use it?

When "Enable DHCP Proxy" is not enabled tha LW AP 3500 cannot get IP address if it is connected directly to LWC... when i add this option then on both LW AP 3500 - one connected to WLC and second directly to switch give me DHCP address from external DHCP but gateway sets as LWC management IP.
I made test - connected client witout "Enable DHCP Proxy":
Client IP 192.168.1.201 (correct in dhcp server logs), default GW 192.168.1.1 (correct gateway for this DHCP) correct dnses and in windws ipconfig i see "Server DHCP 192.168.1.1" all is correct.
Disconnected client and clicked "Enable DHCP Proxy":
Client IP 192.168.1.201 (correct in dhcp server logs), default GW 192.168.1.252 incorrect gateway - ip of WLC management interface) correct dnses and in windws ipconfig i see "Server DHCP 1.1.1.1" that shows that WLC modified DHCP packets... but what it try to set default GW as WLC?
WLC data:
Software Version
7.0.98.0
I can attach screenshots and any other configutation if you need.

Switchports of wlc 2100 dont bridge to rest of the LAN

Hi,
I've configured several WLC's before but I'm new to the 2100 series. I'm a bit confused in the way the 8 ports function. I have the following setup:
2 AP's (1131AG)
3 clients's (wired)
All five connected to WLC on ports 8,7,6,5,4
WLC port 1 is connected to a 24 port switch, non Cisco, so no CDP info available (may that matter).
The whole network should be an untagged Vlan. This is also the way I've runned the basic setup. AP int + MGM int are both untagged configured on port 1.
So I would like the 8 ports to function as an "expansion" to the 24 port switch. But for some reason there is no traffic possible between the wired clients+ap's on the WLC and the rest of the network.
Both sides can ping the AP int + MGM int of the WLC.
DHCP proxy works as well, the AP's get their IP, the wired client's dont.
As soon as the AP tries to resolve CISCO-CAPWAP-CONTROLLER.domain.local it fails, when connected to the 24 port switch, it succeeds, because the DNS server is on that side.
Am I missing something here?
Thanks for your help!
Update: WLC is running the latest version7

The ports on the 2106 are designed to support AP connections or an uplink to a switch. They will not work with PC's connected to them.

1921 rack mount

1921 router doesn't ship with rack mount kit.
How would cisco sugest mount this in the rack?

Hello, I cannot find it on this table.
Table 16. Cables, Rack-Mount Brackets, Blank Faceplates, and FIPS Shields for Cisco 3900, 2900, and 1900 Series Routers
Ordering SKU
Description
CAB-CONSOLE-RJ45
Console Cable 6ft with RJ45 and DB9F (Both system and spare)
CAB-AUX-RJ45
Auxiliary Cable 8ft with RJ45 and DB25M (Both system and spare)
CAB-CONSOLE-USB
Console Cable 6 ft with USB Type A and mini-B connectors (Both system and spare)
ACS-3900-RM-23=
23 inch rack mount kit for Cisco 3925 - 3945EISR (only as spare)
ACS-2900-RM-23=
23 inch rack mount kit for Cisco 2911/2921/2951 ISR (only as spare)
ACS-2901-RM-23=
23 inch rack mount kit for Cisco 2901 ISR (only as spare)
SM-S-BLANK=
Removable faceplate for SM slot on Cisco 2900, 3900 ISR (only as spare)
SM-BLANK-KIT=
Blank faceplate for SM slot with divider on Cisco 2951 & 3925 (only as spare)
HWIC-BLANK=
Blank faceplate for HWIC/EHWIC slot on Cisco ISR (only as spare)
HWIC-BLANK-KIT=
Blank faceplate for HWIC slot with divider for Cisco1941 ISR (only as spare)
HWIC-SLOT-DIVIDER=
HWIC/EHWIC Slot Divider (Guide) for Cisco 1900, 2900, 3900 ISR (only as spare)
SM-SLOT-DIVIDER=
SM Slot Divider (Guide) for Cisco 2900, 3900 ISR (only as spare)
ACS-CF-COVER=
Compact Flash Cover (Guard) for Cisco 1900, 2900, 3900 ISR (only as spare)
FIPS-SHIELD-3900=
FIPS opacity shield for Cisco 3925 - 3945EISR
FIPS-SHIELD-2921=
FIPS opacity shield for Cisco 2921 ISR
FIPS-SHIELD-2951=
FIPS opacity shield for Cisco 2951 ISR
FIPS-SHIELD-2911=
FIPS opacity shield for Cisco 2911 ISR
FIPS-SHIELD-2901=
FIPS opacity shield for Cisco 2901 ISR
FIPS-SHIELD-1900=
FIPS opacity shield for Cisco 1905, Cisco 1921 ISR

Upgradinin to OES 11 sp1 ,Mount options of root

Hi
Got a Ques about
"Changing the Mount Options Before an Upgrade"
in "Preparing the Server You Are Upgrading"
I sazs
I should change to "mount by Device ID or PATH"
My partitions are
dev/sda = 200 MB boot ( = no problems to change to Device boot)
dev/sdb = 20 GB Linux LVM
made as a VG01
containing a swap volume on 1,5 GB + the rest as 18,5GB root volume
Here I cant Change anything ....in the SDB and volumes are the "device/path" options greyed out, Is this OK
It still warns me about "upgrading"
Please advice

Originally Posted by KBOYLE
Landersson wrote:
>
> Hi
> Got a Ques about
> "Changing the Mount Options Before an Upgrade"
> in "Preparing the Server You Are Upgrading"
If you only have one hard drive, I wouldn't worry about it. With two
hard drives, for example, sdb could appear as sda and vise versa.
With multiple hard drives or multiple paths to your storage device the
device name can change depending upon which one SLES encounters first.
By assigning permanent names (mount by Device ID or PATH) that won't
happen.
Kevin Boyle - Knowledge Partner
If you find this post helpful and are logged into the web interface,
show your appreciation and click on the star below...
Thanks for Your anwser ,
I Doo got a serie of servers tha needs update,
all got SDA1 as boot =20 MB and the rest as LVM (SDB) Swap and root ,,, LVM just to be able to expand. all ext3
I still don't get how and where to "change"
Sorry for my extreme sluggish mind
Well My fstab looks like
/dev/VG00/swap swap swap defaults 0 0
/dev/VG00/root / ext3 acl,user_xattr 1 1
/dev/sda1 /boot ext3 acl,user_xattr 1 2
proc /proc proc defaults 0 0
sysfs /sys sysfs noauto 0 0
debugfs /sys/kernel/debug debugfs noauto 0 0
usbfs /proc/bus/usb usbfs noauto 0 0
And
menu.lst
# Modified by YaST2. Last modification on Tue Jul 2 14:03:41 CEST 2013
default 0
timeout 8
##YaST - generic_mbr
gfxmenu (hd0,0)/message
##YaST - activate
###Don't change this comment - YaST2 identifier: Original name: linux###
title SUSE Linux Enterprise Server 11 SP1 - 2.6.32.12-0.7
root (hd0,0)
kernel /vmlinuz-2.6.32.12-0.7-default root=/dev/VG00/root resume=/dev/VG00/swap
splash=silent crashkernel=128M-:64M showopts vga=0x317
initrd /initrd-2.6.32.12-0.7-default
###Don't change this comment - YaST2 identifier: Original name: failsafe###
title Failsafe -- SUSE Linux Enterprise Server 11 SP1 - 2.6.32.12-0.7
root (hd0,0)
kernel /vmlinuz-2.6.32.12-0.7-default root=/dev/VG00/root showopts ide=nodma apm=off
noresume edd=off powersaved=off nohz=off highres=off processor.max_cstate=1 nomodeset
x11failsafe vga=0x317
initrd /initrd-2.6.32.12-0.7-default
###Don't change this comment - YaST2 identifier: Original name: floppy###
title Floppy
rootnoverify (fd0)
chainloader +1
devpts /dev/pts devpts mode=0620,gid=5 0 0
And bootloader
## Path: System/Bootloader
## Description: Bootloader configuration
## Type: list(grub,lilo,none)
## Default: grub
LOADER_TYPE="grub"
DEFAULT_NAME="SUSE Linux Enterprise Server 11 SP1 - 2.6.32.12-0.7"
DEFAULT_APPEND="resume=/dev/VG00/swap splash=silent crashkernel=128M-:64M showopts"
DEFAULT_VGA="0x317"
FAILSAFE_APPEND="showopts ide=nodma apm=off noresume edd=off powersaved=off nohz=off
highres=off processor.max_cstate=1 nomodeset x11failsafe"
FAILSAFE_VGA="0x317"
XEN_KERNEL_APPEND="resume=/dev/VG00/swap splash=silent showopts"
XEN_APPEND=""
XEN_VGA="0x317"
## Path: System/Bootloader
## Description: Bootloader configuration
## Type: yesno
## Default: no
# Should the boot cycle detection be used to
# avoid unconditional reboot cycles of not
# supervised system.
CYCLE_DETECTION="no"
## Type: integer(0:)
## Default: 1
# The number of the entry in grub's menu.lst
# which should be used on the next reboot cycle.
# Note that the first entry has the number 0.
CYCLE_NEXT_ENTRY="1"
## Path: System/Bootloader
## Description: Bootloader configuration
## Type: list(floppy,mbr,root,boot,custom,none)
## Default: mbr
# Location of boot loader.
# For making the change effect run bootloader configuration tool
LOADER_LOCATION=""
'xxxxxxxxxxxxxxxxxxxxx
And https://www.novell.com/documentation...a/bv6uejh.html section 5.4.1 doesnt make any sense for mee

Rack-mounted Power Mac

Quite often, I go on the road with my music production hardware - think of it as a "roving studio." It's quite cumbersome and problematic to lug around a Power Mac Dual G5 tower. It would be so much nicer if there were a rack-mounted version of the Power Mac that I could install in my music equipment rack. I've checked out an Xserve (as it comes in the desired form factor), but it's unclear to me if a) I can use it as a non-server, and b) the AppleCare options. (After all, for me, it wouldn't be a server, so I don't (can't) pay for "server" support.) Does Apple offer a rack configuration for a Power Mac Dual G5 "workstation?" (Or could I buy an Xserve and use it as such - with appropriately-priced (i.e. "workstation") support?)
Mac OS X (10.4.7)

There are vertical rack mounted solutions, but of course this isn't the best use of space.
The G5 needed a bigger case to handle the larger cooling systems and all the expansion options, it's impossible to please everyone. It's not really designed to sit in a rack, but next to a desktop.
I wouldn't use a X-Serve as a desktop machine because your expansion options are limited, video cards may be hard to find for instance. Not much in the way of connectivity either.
There is a penalty for the 1U design.
Now since you roll your rack around from place to place, why not have someone build you a G5 case with wheels and a long handle that you can roll that around from place to place instead?
All you have to do is pay a visit to your local metal shop and find some sturdy fat wheelbarrow wheels at the local hardware store.
I say wheel barrow wheels because you can keep them under-inflated and they absorb shock better.
Heck at my hardware store there is angle iron (aluminum) for sale that with a few bolts and a little ingenuity (and a metal cut off wheel for my chop saw, metal drill bits) I could build a cart for my G5. Take it down to a welding shop and have them make it stronger with welds.
Necessity breeds invention.

Rack mount kits doesn't fit the depth of Agilent rack

I have a PXI 1085 Chassis which I want to mount in an Agilent rack. I purchased the front and rear rack mount kits, the height and width are great, but the depth of my rack doesn’t allow me to use both the front and rear rack mount kits. Is there some kind of adapter I can buy which will extend the rear rack mount so that it can reach the back?

Hi Chall,
Unfortuantely we only offer the kits for a certain size range. If this does not fit your rack then you will have to create a custom rack mount.
Regards,
Kaitlin N.
National Instruments
Applications Engineer

QFS mount options not getting noticed.

Hi I have a small issue it seems that none of my QFS directives are getting noticed im not sure if this is true or not but this is what I have tried and i am unable to verify that these mount options are actually taking effect..
This is QFS Version 4 revision 4.0.26FA
in my /etc/opt/SUNWsamfs/samfs.cmd I have the following options
fs = qfs1
nosuid
sync_meta = 0
qwrite
readahead = 4096
writebehind = 1024
after mounting my file system why are these options not listed in mnttab
qfs1 /qfs1 samfs dev=1d80036 1048280993
using dd/time to write data to this file system im getting the exact same performance no matter what options I set. another reason why I think these options are being ignored is the following
if I set for example fs = qfs1 and high = 70 low = 30 when I check samu [m] option I dont see those values reflected in the m output so what im asking is there anyway to verifty that my mount options are being set occordinly ?
Yes I did use mount -o nosuid,qwrite,etc.. /qfs1 still no difference and even placing the options in vfstab seems to not make any difference.
last but not lease if i do a samtrace -V while mounting my /qfs1 filesystem I see the following
00100000 readahead (1048576) <<--- still seems to use the default values 1024
00080000 writebehind (524288) <<-- 512 look @ my samfs.cmd file this should but not the value.
Any assistance would be nice.

Hi There! Sorry, it took so long to get back to you. This should help:
The samu N display shows all the mount options. You can also use the samfsinfo command to see file system build information. If the samfs.cmd options are not being picked up, make sure the file is formatted correctly (no odd characters) and is in the proper location, /etc/opt/SUNWsamfs/samfs.cmd . Then "pkill -HUP sam-fsd" to assure the daemon has picked up the file's contents, and then mount the file system.

WLC 2100 Series Rack Mount Option

Similar Messages

Maybe you are looking for