WLC 2106 Configuration steps

I have WLC 2106,And 5 LWAP, 3 Cat3560 Switches.and my 2851 CME router providing DHCP for Data VLAN 1 nad Voice VLAN 100
any one can please help me how to do the basic configuration
when i configure Managment and AP manager on WLC 2106 on untaged VLAN 0 i can able to ping but when i cahnged the VLAN to 1 im not able to communicate to WLC from switch or any port from WLC
please help me to configure the WLC
Thanks & Regards
PRajoth

The software guide states "A zero value for the VLAN identifier (on the Controller > Interfaces page) means that the interface is untagged.
The default (untagged) native VLAN on Cisco switches is VLAN 1. When controller interfaces are configured as tagged (meaning that the VLAN identifier is set to a non-zero value), the VLAN must be allowed on the 802.1Q trunk configuration on the neighbor switch and not be the native untagged VLAN.
Cisco recommends that only tagged VLANs be used on the controller. You should also allow only relevant VLANs on the neighbor switch's 802.1Q trunk connections to controller ports. All other VLANs should be disallowed or pruned in the switch port trunk configuration. This practice is extremely important for optimal performance of the controller.
Note Cisco recommends that you assign one set of VLANs for WLANs and a different set of VLANs for management interfaces to ensure that controllers properly route VLAN traffic"
Can you supply a screen shot of the interfaces page from your WLC and supply the WLC switch port configuration also? Just to sanity check what you have so far?

Similar Messages

  • Want to configure wpa2 enterprise in wlc 2106

    Hi,
    I want to configure the wlc 2106 with wpa2 enterprise .... i reckon that iI need ACS server ( Radius Server ) with server certificate as well client certificate.
    how do i configure the redius server to get access through wpa2 enterprise .. If i am wrong , what are all things required to enable wpa2 enterprise with AES encryption .
    Is it possible to get the evalution copy of acs server with certificate ?
    how to go ahead for the same .
    It would be great help me to get the proper answer  for configuration of wpa2 enterprise with AES ...

    The below link may help you..
    http://www.cisco.com/en/US/products/ps6366/products_configuration_example09186a008095382f.shtml
    Regards
    Surendra

  • WLC-2106 and multiple interfaces on the same network

    Hi there,
    I recently created a TAC request to the Cisco support regarding our WLC-2106, but they could not help me. Basically I just learned that you can create new interfaces for the wireless LAN controller and then dedicate them to a given wireless network (SSID). This way I could more effectively utilize network bandwidth also. Problem is that all of the interfaces have to be in a different network segment in order to work, which is not what I want. I specifically want to have several interfaces on the same network segment.
    Has anyone tried to accomplish the same?

    Basically what I've misunderstood is that all the traffic generated by our wireless clients have been going through the single 100Mbit/s ethernet port on the wireless LAN controller (management interface), and to mitigate this I thought I could create new interfaces (ports) and dedicate those to given WLAN networks.. I see now that this is not supported. Not inside the same network at least.
    So, by reading further and consulting my best friend Google I learned about a setting called "AP Mode". Changing that from Local (the default) to H-REAP the APs should not route their traffic anymore through the management interface on the wireless controller, but instead route all the client traffic directly to the local LAN. This way you effectively remove the 100Mbit/s bottle-neck when all the APs were using the management interface both for configuration and client data traffic.
    It seems you also have to enable H-REAP Local switching from a given WLAN network in addition to changing the AP Mode of your access points to H-REAP. I'm still in the testing phase here so should anyone have any insight to this, I'd be greatful to hear more.

  • WLC 2106 problem

    Hello,
    I have problem with new one WLC 2106 controller. I make this basic configuration (after reset):
    (Cisco Controller) >show interface summary
    Interface Name                   Port Vlan Id  IP Address      Type    Ap Mgr Guest
    ap-manager                       1    10       10.10.10.21     Static  Yes    No
    management                       1    10       10.10.10.20     Static  No     No
    virtual                          N/A  N/A      1.1.1.1         Static  No     No
    At this point, everything works OK. Controller is accesible via HTTPS, AP (one 1130) is connected too. But next I need create new WLAN and another interface VLAN - named ak-lan
    config interface create ak-lan
    config interface port ak-lan 1
    HTTPS acces is still working, but when I configure IP adress:
    config interface address dynamic-interface ak-lan 10.10.11.10 255.255.255.0 10.10.11.1
    HTTPS acces stops. In fact, it seem like HTTPS starts on new interface - it's accesible via 10.10.11.10, but (after certificate warning) shows only empty page (Page is not accesible..)
    I dont have an idea why. I tray downgrade software (originaly comes with 7.0.98.0) to 6.0.196.0, whitch I use on another same controller, but the behavior is the same. Now I use software 6.0.199.4. Again the same behavior.
    "show interface summary" says:
    (Cisco Controller) >show interface summary
    Interface Name                   Port Vlan Id  IP Address      Type    Ap Mgr Guest
    ak-lan                           1    11       10.10.11.10     Dynamic No     No
    ap-manager                       1    10       10.10.10.21     Static  Yes    No
    management                       1    10       10.10.10.20     Static  No     No
    virtual                          N/A  N/A      1.1.1.1         Static  No     No
    (Cisco Controller) >
    All interfaces (excluding virtual) matched to ping. All ïnterfaces have netmask 255.255.255.0.
    There was another strange thing - "show sysinfo" says that I use sw 6.0.199.4 and emergency is 7.0.98.0, but "show boot" says:
    (Cisco Controller) >show boot
    Primary Boot Image............................... 6.0.199.4 (active)
    Backup Boot Image................................ 6.0.196.0
    (Cisco Controller) >
    (Cisco Controller) >show sysinfo
    Manufacturer's Name.............................. Cisco Systems Inc.
    Product Name..................................... Cisco Controller
    Product Version.................................. 6.0.199.4
    RTOS Version..................................... 6.0.199.4
    Bootloader Version............................... 4.0.191.0
    Emergency Image Version.......................... 7.0.98.0
    Build Type....................................... DATA + WPS
    System Name...................................... ak-wlc
    System Location..................................
    System Contact...................................
    System ObjectID.................................. 1.3.6.1.4.1.9.1.828
    IP Address....................................... 10.10.10.20
    System Up Time................................... 0 days 0 hrs 46 mins 35 secs
    System Timezone Location.........................
    Configured Country............................... DE  - Germany
    Operating Environment............................ Commercial (0 to 40 C)
    Internal Temp Alarm Limits....................... 0 to 65 C
    Internal Temperature............................. +55 C
    State of 802.11b Network......................... Enabled
    State of 802.11a Network......................... Enabled
    Number of WLANs.................................. 0
    3rd Party Access Point Support................... Disabled
    Number of Active Clients......................... 0
    Burned-in MAC Address............................ E0:5F:B9:63:7B:00

    Switch is C2960, port Gi0/2:
    Gi0/2     T wlc              connected    trunk      a-full  a-100 10/100/1000BaseTX
    interface GigabitEthernet0/2
    description T wlc
    switchport trunk allowed vlan 10,11,100
    switchport mode trunk
    end
    VLANs are set properly. Router is ASA 5510, and routing is fine. Morever, interfaces on WLC is accesible via ping (I dot't try telnet or ssh).

  • OBIEE 11g installation failed multiple times at Distributing Repository Configuration Step

    Hi,
    I am getting the following error during the Distributing Repository Configuration step in the OBIEE 11g 11.1.1.7 enterprise installation in Windows 8 system.
    Severe: Element Type:Domain
    Element id: null
    Operation result: failed to obtain domain file lock
    Detail Message: java.util.concurrent.timeoutException.Timeout;
    waiting for lock: Domain config lock;
    c:\OBIEE\MIDDLE~1\USER_p~1\domains\EAM_DO~1\config\FMWCON~1\biee-config.lock;[121 secs]
    Step Distributing Repository failed
    Configuration Action 'Distributing Repository' has failed. Please check logs for details.
    Step Distributing repository failed
    I checked another blog for this https://forums.oracle.com/thread/2565716 and even there the explanation doesn't convince me.
    I tried to look at the Locale of my system where I am installing and I could see it is using Eng-Us by default. One way suggested to check the Unicode format from the web browser and I could check that too to be UTF-8 as suggested by someone on some other blog.
    I checked in the logs too as suggested by the Installation dialogue box but it didn't seem much conclusive too.
    Here is the snapshot of the log file which I could found.
    INFO: Current Inventory:
      Oracle Home: OraDb11g_home1
      This Oracle Home has not been changed in this session.
      Oracle Home: OH1858390736
      This Oracle Home has not been changed in this session.
      Oracle Home: OH440082373
      This Oracle Home has not been changed in this session.
      Oracle Home: OH440082374
      This Oracle Home has not been changed in this session.
      Oracle Home: OH1597391518
      This Oracle Home has not been changed in this session.
      Oracle Home: OH1285215443
      This Oracle Home has not been changed in this session.
    INFO: Ending the inventory Session
    INFO: Using an existing InstallAreaControl for this Inventory Session with existing access level 1
    INFO: Using an existing InstallAreaControl for this Inventory Session with existing access level 1
    INFO: Using an existing InstallAreaControl for this Inventory Session with existing access level 1
    INFO: The ORACLE_CONFIG_HOME env var is set to
    INFO: The ORACLE_CONFIG_HOME env var is set to
    INFO: The ORACLE_CONFIG_HOME env var is set to
    INFO: The ORACLE_CONFIG_HOME env var is set to
    INFO: The ORACLE_CONFIG_HOME env var is set to
    INFO: The ORACLE_CONFIG_HOME env var is set to
    INFO: The ORACLE_CONFIG_HOME env var is set to
    INFO: The ORACLE_CONFIG_HOME env var is set to
    INFO: The ORACLE_CONFIG_HOME env var is set to
    INFO: The ORACLE_CONFIG_HOME env var is set to
    INFO: The ORACLE_CONFIG_HOME env var is set to
    INFO: The ORACLE_CONFIG_HOME env var is set to
    INFO: The ORACLE_CONFIG_HOME env var is set to
    INFO: The ORACLE_CONFIG_HOME env var is set to
    INFO: The ORACLE_CONFIG_HOME env var is set to
    INFO: The ORACLE_CONFIG_HOME env var is set to
    Can someone please help me with this since I am stuck with for quite some time now.
    Is there any way to check in command prompt to check the locale as required by the system.
    What could be the issue here?
    Thanks,
    Nitin

    Hi all,
    We are able to resolve the above issue with the below solution.
    Root cause of the issue:
    You may have a temp directory in the path C:\Documents and Settings\user_name\Local Settings\Temp. You got the above mentioned exception because of the temp directory path having spaces_+ in it.
    Solution:
    1. Create a new directory called TEMP in a different location for ex: C:\TEMP
    2. Now, Right click on My computer --> Properties --> Advanced --> click on Environment Variables.
    3. You should be having TEMP and TMP as variables under user variables section pointing to the C:\Documents and Settings\user_name\Local Settings\Temp path.
    4. Edit the TEMP and TMP variables and mention C:\TEMP in the variable value.
    5. Deinstall and re-install OBIEE 11g.
    Happy OBIEE 11g installation!!
    Thanks,
    Rajesh Gurram

  • Product costing by sales order configuration steps

    hi
    plz send me product costing by sales order configuration steps.
    sir, i know manufacturing order configuration step but i do not sales order configuration.
    in the sales order also is same as manufacturing order like first we have to make planning cost , the planning cost should be updated to material master and next configure the actual cost.
    for first step- costing variant -okkn
    next -costing variant -opl1
    for sales order also same we need to update planning price first- what is costing variant
    for actual cost - what is costing variant
    plz tell me detail
    regards,
    sowmya
    Moderator: Please, read forum rules before posting

    Hi Sashikanth,
       Please send me the Configuration document for make to sales order.We are at Blue print stage need some docment for make to sales order.Plese send me the document it will will be very help full for me.
    My id is [email protected]
    Thanks in advance
    Regards,
    Nagaraju
    Edited by: nagaraju sami on Mar 9, 2008 11:58 AM

  • Which driver to use in the BPM Configuration Steps?

    Hi,
    I´m in the BPM configuration steps and we will use BPM on a Weblogic Server, I´m in the step when you need to create to JDBC Data Sources for the Enterprise and Directory Databases, do you know which driver shoul I use? should it be XA o Non-XA?
    Thanx in Advanced!
    Kind Regards,
    Gerardo J

    Since there are no drivers, you can create your own, request one, use the Instrument I/O Assistant, or hope someone has one and posts it here. For help on creating one or requesting one, see the main Instrument Driver Network page. As long as you are familiar with the instrument and have the manual, creating a driver is not that hard.

  • Configuration steps for Extended Classic Scenario

    Hi All,
    Could you please let me know what are the configuration steps required for extended classic scenario.
    Thanks in advance

    Hi,
    Important Settings that Determine the Extended Classic Scenario
    The following settings are required for the extended classic scenario:
    u2022 At least one backend materials management system and accounting system is connected to the SAP SRM system and defined in the configuration setting Define Backend Systems.
    u2022 Product categories from the backend procurement system are replicated and used in the SAP SRM system.
    u2022 The target system for each product category is the backend system in the configuration setting Define Backend Systems for Product Category. Optionally, BADI BBP_DETERMINE_LOGSYS is implemented to determine the backend system.
    u2022 The extended classic scenario is activated in the configuration setting Activate Extended Classic Scenario. Alternatively, BAdI BBP_EXTLOCALPO_BADI is implemented to control the extended classic scenario based on customer defined rules.
    u2022 If the backend system is an SAP R/3 version lower than 4.6B, you must define local purchasing organizations and purchasing groups.
    u2022 If the backend system is an SAP R/3 version 4.6B or higher, you need to map the purchasing group used in the purchase order to the backend purchase group in one of the following ways:
    u2022 Use a backend purchasing organization and purchasing group in the shopping cart and purchase order.
    u2022 Use BAdI BBP_PGRP_FIND to determine a backend purchasing group in the shopping cart.
    u2022 If a local (created in SAP SRM without reference to a backend system) purchasing group and purchasing organization are used, then a valid backend purchasing group is assigned to the RFC user that created the backend purchase order. This assignment is made in the backend system using user parameter EKG in Transaction code SU01.
    u2022 Implement the user exit of the BAPIs BAPI_PO_CREATE1 (EXIT_SAPL2012_001 and EXIT_SAPL2012_003), and BAPI_PO_CHANGE (EXIT_SAPL2012_002 and EXIT_SAPL2012_004) to determine the purchasing group with a customer- specific logic.
    This is for your additional information.
    Hope this helps.
    Regards,
    Vikas

  • Configuration steps to create New Special GL

    HI,
    Can any one please send me configuration steps to create New Special GL. My client required to create new special GL for Rent Advance.
    NOTE: hear I am not asking how configuration steps for assigning GL accounts for existing Special GL. I want new Special GL to be Create for rent advance.
    It’s very urgent
    My mail id "[email protected]"
    Thank you
    mahesh

    Hi,
    go to transaction code fbzp where you assign GL account to the spl GL indicator.
    Go and create a new spl GL indicator there by clicking create new.
    Bye

  • Give me the Configuration steps  for intercompany billing and third party s

    Hi Gurus,
    Give me  the Configuration steps  for intercompany billing and third party sales and give me a brief description with examples.
    Regards,
    YSR

    Dear YSR
    Check the links
    [Cross Company Configuration|http://help.sap.com/bp_bblibrary/500/Documentation/J62_BB_ConfigGuide_EN_DE.doc]
    [Third Party Without Shipping Notification|http://help.sap.com/bestpractices/BBLibrary/html/J55_ThirdPartyWOSN_EN_US.htm]
    Third party order processing is as follows:
    Assume three companies X, Y and Z
    X - The company,
    y - The customer
    Z - Vendor
    When ever X gets a PO from Y to supply some goods, X has an option of either manufacturing those goods or procuring those goods.
    If he is procuring the goods, there are two methods that are generally followed:
    Method 1)
    After receiving the PO from Y, X creates a sales order against Y.
    Now at the same time he also creates a PO to a vendor Z to produce the goods
    Z produces the goods and supplies to X
    X receives the goods from Z
    Then X delivers the same goods to Y.
    After that X invoices Y and Z invoices X.
    Note : Here there is no direct/ Indirect relation between Z and Y.
    This process is known as Trading Process. and the Material here is created  with Material type HAWA.
    The other method is a Third party order processing method:
    Here the glaring difference is that instead of Z supplying the material to X and X in turn supplying the same material to Y.
    X authorizes Z to supply the material to Y on his behalf and notify him once the delivery is complete.
    Now Z supplies the material to Y and acknowledges the same to X.
    Z  will send a copy of delivery acknowledgement and invoice to X.
    After receiving the delivery confirmation and invoice from Z, X has to verify the invoice and this process is known as invoice verification and is done in SAP through Tcode MIRO.
    The next step for X  is to create an invoice and submit to Y
    Only after the invoice verification document is posted  then only X can create an invoice for Y.
    This is the business flow that is followed for third party order configuration.
    There are few steps that have to be configured to enable the system to function as mentioned above.
    Step1)
    If you are always followwing a third party process for a material then you have to create the material using item category group BANS.
    The procument type should be marked as External procurement (F) in MRP 2 view of the material master record.
    if you are not always allowing third party order processing then u can create a material master record with item category group as NORM and the procurement type should be marked as ( X) meaning both types of procurment ( in house manufacturing and external procurement).
    Step 2)
    the item category in the order should be manually changed as TAS.
    For that you need to confugure the item category determination
    ord type + item cat grp + usge + Hiv level = Item cat + Manual item cat
    OR + NORM +      +       = TAN . + TAS
    OR + BANS +       +       = TAS
    Step 3)
    make sure that during the item category configuration for TAS  you need to mark relevnat for billing indicator as F
    Step 4)
    The schedule line cateogry for this type should be CS.
    make sure that you mark  subsequent type as NB - purchase requisition  in this schedule line category as this will trigger the purchase requision order immediately after the creation of the sales order and the PO to vendor is created against this purchase requiesion.
    thanks
    G. Lakshmipathi

  • Business partner configuration steps in treasury

    Reqiure Business partner configuration steps in treasury.
    While creating business partner i get the message :Personal address doesnot exist.
    How to rectify this?

    No reply.Closed.

  • Error at DB downtime configuration step in SAP installation

    Hello Gurus,
                  While installing CRM IDES  5.0 I am stuck at DB downtime configuration (step 9). After shutting down MSSQL server services are not automatically started. In usual case it should be. Its giving "could not start the MSSQLSERVER" service on host. And my MSSQL services are not starting either it is giving Named pipes provider, error:40 - could not open a connection to SQL Server. If any one faced similar kind of problems sugguest on this.
    Regards,
    Murali

    Check your event log why your database is not coming up.
    Markus

  • GC install fails on OMS Configuration step with NodeManager

    I'm trying to install OEM Grid Control and I'm having some problems getting past the OMS Configuration step in the installation. I'm not very familiar with Oracle products. I've completed all the configuration steps listed in the documentation and in order to resolve an earlier problem, I deleted the Keynectis and Telesec certificates from the cacerts java keystore. NodeManager is being run as a service, though I think the configuration process is launching a new instance because it can't connect to the service. I've also been unable to connect to the service through the WLST nmConnect function, though it's possible my parameters are incorrect. If the only problem is that GCDomain is not registered in the nodemanager.domains file, I'm not sure what I'm doing wrong, because I put it in the nodemanager.domains file located at C:\Oracle\Middleware\wlserver_10.3\common\nodemanager:
    #Domains and directories created by Configuration Wizard
    #Fri Apr 22 15:23:16 EDT 2011
    wl_server=C\:\\Oracle\\Middleware\\wlserver_10.3\\samples\\domains\\wl_server
    medrec-spring=C\:\\Oracle\\Middleware\\wlserver_10.3\\samples\\domains\\medrec-spring
    GCDomain=C\:\\Oracle\\gc_inst\\user_projects\\domains\\GCDomain
    medrec=C\:\\Oracle\\Middleware\\wlserver_10.3\\samples\\domains\\medrec
    note - the file paths are correct and use escaped slashes where appropriate, but this message board system is turning the last double backslash into a line break. I can't find any html solution that works, so just take my word for it
    I restarted NodeManager after making the change as well. Any help would be appreciated. Thanks.
    Details:
    Machine - Windows Server 2008 x64
    DB - 11gR2
    WLS - 10.3.2
    GC - 11.1.0.1
    Install Log:
    FINE: Connecting to Node Manager ... Apr 22, 2011 3:23:19 PM oracle.sysman.omsca.util.ProcessOutputReader run
    FINE: <Apr 22, 2011 3:23:19 PM EDT> <Notice> <Security> <BEA-090898> <Ignoring the trusted CA certificate "CN=KEYNECTIS ROOT CA,OU=ROOT,O=KEYNECTIS,C=FR". The loading of the trusted certificate list raised a certificate parsing exception PKIX: Unsupported OID in the AlgorithmIdentifier object: 1.2.840.113549.1.1.11.> Apr 22, 2011 3:23:19 PM oracle.sysman.omsca.util.ProcessOutputReader run
    FINE: <Apr 22, 2011 3:23:19 PM EDT> <Notice> <Security> <BEA-090898> <Ignoring the trusted CA certificate "CN=T-TeleSec GlobalRoot Class 3,OU=T-Systems Trust Center,O=T-Systems Enterprise Services GmbH,C=DE". The loading of the trusted certificate list raised a certificate parsing exception PKIX: Unsupported OID in the AlgorithmIdentifier object: 1.2.840.113549.1.1.11.> Apr 22, 2011 3:23:19 PM oracle.sysman.omsca.util.ProcessOutputReader run
    FINE: <Apr 22, 2011 3:23:19 PM EDT> <Notice> <Security> <BEA-090898> <Ignoring the trusted CA certificate "CN=T-TeleSec GlobalRoot Class 2,OU=T-Systems Trust Center,O=T-Systems Enterprise Services GmbH,C=DE". The loading of the trusted certificate list raised a certificate parsing exception PKIX: Unsupported OID in the AlgorithmIdentifier object: 1.2.840.113549.1.1.11.> Apr 22, 2011 3:23:20 PM oracle.sysman.omsca.util.ProcessOutputReader run
    FINE: This Exception occurred at Fri Apr 22 15:23:20 EDT 2011. Apr 22, 2011 3:23:20 PM oracle.sysman.omsca.util.ProcessOutputReader run
    FINE: weblogic.nodemanager.NMConnectException: Connection refused: connect. Could not connect to NodeManager. Check that it is running at win2008x64-2:7,401. Apr 22, 2011 3:23:20 PM oracle.sysman.omsca.util.ProcessOutputReader run
    FINE:      at java.net.PlainSocketImpl.socketConnect(Native Method) Apr 22, 2011 3:23:20 PM oracle.sysman.omsca.util.ProcessOutputReader run
    FINE:      at java.net.PlainSocketImpl.doConnect(PlainSocketImpl.java:333) Apr 22, 2011 3:23:20 PM oracle.sysman.omsca.util.ProcessOutputReader run
    FINE:      at java.net.PlainSocketImpl.connectToAddress(PlainSocketImpl.java:195) Apr 22, 2011 3:23:20 PM oracle.sysman.omsca.util.ProcessOutputReader run
    FINE:      at java.net.PlainSocketImpl.connect(PlainSocketImpl.java:182) Apr 22, 2011 3:23:20 PM oracle.sysman.omsca.util.ProcessOutputReader run
    FINE:      at java.net.SocksSocketImpl.connect(SocksSocketImpl.java:366) Apr 22, 2011 3:23:20 PM oracle.sysman.omsca.util.ProcessOutputReader run
    FINE:      at java.net.Socket.connect(Socket.java:525) Apr 22, 2011 3:23:20 PM oracle.sysman.omsca.util.ProcessOutputReader run
    FINE:      at weblogic.nodemanager.client.SSLClient.createSocket(SSLClient.java:38) Apr 22, 2011 3:23:20 PM oracle.sysman.omsca.util.ProcessOutputReader run
    FINE:      at weblogic.nodemanager.client.NMServerClient.connect(NMServerClient.java:227) Apr 22, 2011 3:23:20 PM oracle.sysman.omsca.util.ProcessOutputReader run
    FINE:      at weblogic.nodemanager.client.NMServerClient.checkConnected(NMServerClient.java:199) Apr 22, 2011 3:23:20 PM oracle.sysman.omsca.util.ProcessOutputReader run
    FINE:      at weblogic.nodemanager.client.NMServerClient.checkConnected(NMServerClient.java:205) Apr 22, 2011 3:23:20 PM oracle.sysman.omsca.util.ProcessOutputReader run
    FINE:      at weblogic.nodemanager.client.NMServerClient.getVersion(NMServerClient.java:52) Apr 22, 2011 3:23:20 PM oracle.sysman.omsca.util.ProcessOutputReader run
    FINE:      at weblogic.management.scripting.NodeManagerService.verifyConnection(NodeManagerService.java:175) Apr 22, 2011 3:23:20 PM oracle.sysman.omsca.util.ProcessOutputReader run
    FINE:      at weblogic.management.scripting.NodeManagerService.nmConnect(NodeManagerService.java:168) Apr 22, 2011 3:23:20 PM oracle.sysman.omsca.util.ProcessOutputReader run
    FINE:      at sun.reflect.NativeMethodAccessorImpl.invoke0(Native Method) Apr 22, 2011 3:23:20 PM oracle.sysman.omsca.util.ProcessOutputReader run
    FINE:      at sun.reflect.NativeMethodAccessorImpl.invoke(NativeMethodAccessorImpl.java:39) Apr 22, 2011 3:23:20 PM oracle.sysman.omsca.util.ProcessOutputReader run
    FINE:      at sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAccessorImpl.java:25) Apr 22, 2011 3:23:20 PM oracle.sysman.omsca.util.ProcessOutputReader run
    FINE:      at java.lang.reflect.Method.invoke(Method.java:597) Apr 22, 2011 3:23:20 PM oracle.sysman.omsca.util.ProcessOutputReader run
    FINE:      at org.python.core.PyReflectedFunction.__call__(Unknown Source) Apr 22, 2011 3:23:20 PM oracle.sysman.omsca.util.ProcessOutputReader run
    FINE:      at org.python.core.PyMethod.__call__(Unknown Source) Apr 22, 2011 3:23:20 PM oracle.sysman.omsca.util.ProcessOutputReader run
    FINE:      at org.python.core.PyObject.__call__(Unknown Source) Apr 22, 2011 3:23:20 PM oracle.sysman.omsca.util.ProcessOutputReader run
    FINE:      at org.python.core.PyObject.invoke(Unknown Source) Apr 22, 2011 3:23:20 PM oracle.sysman.omsca.util.ProcessOutputReader run
    FINE:      at org.python.pycode._pyx2.nmConnect$3(<iostream>:118) Apr 22, 2011 3:23:20 PM oracle.sysman.omsca.util.ProcessOutputReader run
    FINE:      at org.python.pycode._pyx2.call_function(<iostream>) Apr 22, 2011 3:23:20 PM oracle.sysman.omsca.util.ProcessOutputReader run
    FINE:      at org.python.core.PyTableCode.call(Unknown Source) Apr 22, 2011 3:23:20 PM oracle.sysman.omsca.util.ProcessOutputReader run
    FINE:      at org.python.core.PyTableCode.call(Unknown Source) Apr 22, 2011 3:23:20 PM oracle.sysman.omsca.util.ProcessOutputReader run
    FINE:      at org.python.core.PyFunction.__call__(Unknown Source) Apr 22, 2011 3:23:20 PM oracle.sysman.omsca.util.ProcessOutputReader run
    FINE:      at org.python.core.PyObject.__call__(Unknown Source) Apr 22, 2011 3:23:20 PM oracle.sysman.omsca.util.ProcessOutputReader run
    FINE:      at org.python.pycode._pyx41.startNM$1(C:\Oracle\Middleware\oms11g\sysman\omsca\scripts\wls\start_server.py:20) Apr 22, 2011 3:23:20 PM oracle.sysman.omsca.util.ProcessOutputReader run
    FINE:      at org.python.pycode._pyx41.call_function(C:\Oracle\Middleware\oms11g\sysman\omsca\scripts\wls\start_server.py) Apr 22, 2011 3:23:20 PM oracle.sysman.omsca.util.ProcessOutputReader run
    FINE:      at org.python.core.PyTableCode.call(Unknown Source) Apr 22, 2011 3:23:20 PM oracle.sysman.omsca.util.ProcessOutputReader run
    FINE:      at org.python.core.PyTableCode.call(Unknown Source) Apr 22, 2011 3:23:20 PM oracle.sysman.omsca.util.ProcessOutputReader run
    FINE:      at org.python.core.PyFunction.__call__(Unknown Source) Apr 22, 2011 3:23:20 PM oracle.sysman.omsca.util.ProcessOutputReader run
    FINE:      at org.python.pycode._pyx39.f$0(C:\Oracle\Middleware\oms11g\sysman\omsca\scripts\wls\create_em_infra.py:74) Apr 22, 2011 3:23:20 PM oracle.sysman.omsca.util.ProcessOutputReader run
    FINE:      at org.python.pycode._pyx39.call_function(C:\Oracle\Middleware\oms11g\sysman\omsca\scripts\wls\create_em_infra.py) Apr 22, 2011 3:23:20 PM oracle.sysman.omsca.util.ProcessOutputReader run
    FINE:      at org.python.core.PyTableCode.call(Unknown Source) Apr 22, 2011 3:23:20 PM oracle.sysman.omsca.util.ProcessOutputReader run
    FINE:      at org.python.core.PyCode.call(Unknown Source) Apr 22, 2011 3:23:20 PM oracle.sysman.omsca.util.ProcessOutputReader run
    FINE:      at org.python.core.Py.runCode(Unknown Source) Apr 22, 2011 3:23:20 PM oracle.sysman.omsca.util.ProcessOutputReader run
    FINE:      at org.python.util.PythonInterpreter.execfile(Unknown Source) Apr 22, 2011 3:23:20 PM oracle.sysman.omsca.util.ProcessOutputReader run
    FINE:      at weblogic.management.scripting.WLST.main(WLST.java:131) Apr 22, 2011 3:23:20 PM oracle.sysman.omsca.util.ProcessOutputReader run
    FINE:      at sun.reflect.NativeMethodAccessorImpl.invoke0(Native Method) Apr 22, 2011 3:23:20 PM oracle.sysman.omsca.util.ProcessOutputReader run
    FINE:      at sun.reflect.NativeMethodAccessorImpl.invoke(NativeMethodAccessorImpl.java:39) Apr 22, 2011 3:23:20 PM oracle.sysman.omsca.util.ProcessOutputReader run
    FINE:      at sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAccessorImpl.java:25) Apr 22, 2011 3:23:20 PM oracle.sysman.omsca.util.ProcessOutputReader run
    FINE:      at java.lang.reflect.Method.invoke(Method.java:597) Apr 22, 2011 3:23:20 PM oracle.sysman.omsca.util.ProcessOutputReader run
    FINE:      at weblogic.WLST.main(WLST.java:29) Apr 22, 2011 3:23:20 PM oracle.sysman.omsca.util.ProcessOutputReader run
    FINE: Fri Apr 22 15:23:20 EDT 2011 Apr 22, 2011 3:23:20 PM oracle.sysman.omsca.util.ProcessOutputReader run
    FINE: Node Manager is down starting it Apr 22, 2011 3:23:20 PM oracle.sysman.omsca.util.ProcessOutputReader run
    FINE: Not connected to Node Manager Apr 22, 2011 3:23:20 PM oracle.sysman.omsca.util.ProcessOutputReader run
    FINE: Launching NodeManager ...
    Apr 22, 2011 3:23:20 PM oracle.sysman.omsca.util.ProcessOutputReader run
    FINE: Properties: {ListenAddress=win2008x64-2,ListenPort=7401,NodeManagerHome=C:\Oracle\MIDDLE~1\WLSERV~1.3\common\emnodemanager20110422152239,StartScriptEnabled=true,StartScriptName=startEMServer.cmd,}
    Apr 22, 2011 3:23:20 PM oracle.sysman.omsca.util.ProcessOutputReader run
    FINE: Command: C:\Oracle\MIDDLE~1\JROCKI~1.5-3\jre\bin\javaw.exe -classpath "C:\Oracle\MIDDLE~1\JROCKI~1.5-3\jre\lib\rt.jar;C:\Oracle\MIDDLE~1\JROCKI~1.5-3\jre\lib\i18n.jar;C:\Oracle\MIDDLE~1\patch_wls1032\profiles\default\sys_manifest_classpath\weblogic_patch.jar;C:\Oracle\MIDDLE~1\patch_oepe1032\profiles\default\sys_manifest_classpath\weblogic_patch.jar;C:\Oracle\MIDDLE~1\JROCKI~1.5-3\lib\tools.jar;C:\Oracle\MIDDLE~1\utils\config\10.3\config-launch.jar;C:\Oracle\MIDDLE~1\WLSERV~1.3\server\lib\weblogic_sp.jar;C:\Oracle\MIDDLE~1\WLSERV~1.3\server\lib\weblogic.jar;C:\Oracle\MIDDLE~1\modules\features\weblogic.server.modules_10.3.2.0.jar;C:\Oracle\MIDDLE~1\WLSERV~1.3\server\lib\webservices.jar;C:\Oracle\MIDDLE~1\modules\ORGAPA~1.0\lib\ant-all.jar;C:\Oracle\MIDDLE~1\modules\NETSFA~1.0_1\lib\ant-contrib.jar;C:\Oracle\Middleware\oms11g\sysman\jlib\emConfig.jar;C:\Oracle\MIDDLE~1\ORACLE~1\modules\oracle.jrf_11.1.1\jrf-api.jar;C:\Oracle\MIDDLE~1\ORACLE~1\common\wlst\resources\jrf-wlst.jar;C:\Oracle\MIDDLE~1\ORACLE~1\modules\oracle.odl_11.1.1\ojdl.jar;C:\Oracle\MIDDLE~1\ORACLE~1\modules\oracle.odl_11.1.1\ojdl2.jar;C:\Oracle\MIDDLE~1\ORACLE~1\modules\oracle.dms_11.1.1\dms.jar;C:\Oracle\MIDDLE~1\ORACLE~1\modules\oracle.dconfig-infra_11.1.1.jar;C:\Oracle\MIDDLE~1\ORACLE~1\modules\oracle.fabriccommon_11.1.1\fabric-common.jar;C:\Oracle\MIDDLE~1\ORACLE~1\modules\oracle.xdk_11.1.0\xmlparserv2.jar;C:\Oracle\MIDDLE~1\ORACLE~1\modules\oracle.xdk_11.1.0\xml.jar;C:\Oracle\MIDDLE~1\ORACLE~1\modules\oracle.wsm.common_11.1.1\wsm-pmlib.jar;C:\Oracle\MIDDLE~1\ORACLE~1\modules\oracle.wsm.common_11.1.1\wsm-policy-core.jar;C:\Oracle\MIDDLE~1\ORACLE~1\modules\oracle.wsm.common_11.1.1\wsm-secpol.jar;C:\Oracle\MIDDLE~1\ORACLE~1\modules\oracle.wsm.common_11.1.1\wsm-dependencies.jar;C:\Oracle\MIDDLE~1\ORACLE~1\modules\oracle.wsm.policies_11.1.1\wsm-seed-policies.jar;C:\Oracle\MIDDLE~1\ORACLE~1\modules\oracle.webservices_11.1.1\orawsdl.jar;C:\Oracle\MIDDLE~1\ORACLE~1\modules\oracle.webservices_11.1.1\mdds.jar;C:\Oracle\MIDDLE~1\ORACLE~1\modules\oracle.webservices_11.1.1\ws_confmbeans.jar;C:\Oracle\MIDDLE~1\ORACLE~1\modules\org.apache.commons.digester_1.7.jar;C:\Oracle\MIDDLE~1\ORACLE~1\..\modules\javax.xml.bind_2.1.1.jar;C:\Oracle\MIDDLE~1\ORACLE~1\..\modules\javax.activation_1.1.jar;C:\Oracle\MIDDLE~1\ORACLE~1\..\modules\javax.xml.stream_1.1.1.0.jar;C:\Oracle\MIDDLE~1\ORACLE~1\modules\oracle.http_client_11.1.1.jar;C:\Oracle\MIDDLE~1\ORACLE~1\modules\oracle.jmx_11.1.1\jmxframework.jar;C:\Oracle\MIDDLE~1\ORACLE~1\modules\oracle.jmx_11.1.1\jmxspi.jar;C:\Oracle\MIDDLE~1\ORACLE~1\modules\oracle.adf.dconfigbeans_11.1.1.jar;C:\Oracle\MIDDLE~1\ORACLE~1\modules\oracle.adf.share.ca_11.1.1\adf-share-base.jar;C:\Oracle\MIDDLE~1\ORACLE~1\modules\oracle.adf.share.ca_11.1.1\adf-share-ca.jar;C:\Oracle\MIDDLE~1\ORACLE~1\modules\oracle.adf.share_11.1.1\adflogginghandler.jar;C:\Oracle\MIDDLE~1\ORACLE~1\modules\oracle.adf.share_11.1.1\adfsharembean.jar;C:\Oracle\MIDDLE~1\ORACLE~1\modules\oracle.adf.share_11.1.1\commons-el.jar;C:\Oracle\MIDDLE~1\ORACLE~1\modules\oracle.adf.share_11.1.1\jsp-el-api.jar;C:\Oracle\MIDDLE~1\ORACLE~1\modules\oracle.adf.share_11.1.1\oracle-el.jar;C:\Oracle\MIDDLE~1\ORACLE~1\common\wlst\resources\auditwlst.jar;C:\Oracle\MIDDLE~1\ORACLE~1\common\wlst\resources\sslconfigwlst.jar;C:\Oracle\MIDDLE~1\ORACLE~1\common\wlst\resources\oamap_help.jar;C:\Oracle\MIDDLE~1\ORACLE~1\common\wlst\resources\ossoiap_help.jar;C:\Oracle\MIDDLE~1\ORACLE~1\common\wlst\resources\jps-wlst.jar;C:\Oracle\MIDDLE~1\ORACLE~1\modules\oracle.auditprovider_11.1.1\jps-wls-auditprovider.jar;C:\Oracle\MIDDLE~1\ORACLE~1\modules\oracle.jps_11.1.1\jps-manifest.jar;C:\Oracle\MIDDLE~1\ORACLE~1\modules\oracle.jps_11.1.1\jps-mbeans.jar;C:\Oracle\MIDDLE~1\ORACLE~1\modules\oracle.jps_11.1.1\jps-upgrade.jar;C:\Oracle\MIDDLE~1\ORACLE~1\modules\oracle.jps_11.1.1\jps-patching.jar;C:\Oracle\MIDDLE~1\ORACLE~1\common\wlst\lib\ADF-SH~1.JAR;C:\Oracle\MIDDLE~1\ORACLE~1\common\wlst\lib\mdswlst.jar;C:\Oracle\MIDDLE~1\ORACLE~1\common\wlst\RESOUR~1\AUDITW~1.JAR;C:\Oracle\MIDDLE~1\ORACLE~1\common\wlst\RESOUR~1\jps-wlst.jar;C:\Oracle\MIDDLE~1\ORACLE~1\common\wlst\RESOUR~1\jrf-wlst.jar;C:\Oracle\MIDDLE~1\ORACLE~1\common\wlst\RESOUR~1\OAMAP_~1.JAR;C:\Oracle\MIDDLE~1\ORACLE~1\common\wlst\RESOUR~1\OAMAUT~1.JAR;C:\Oracle\MIDDLE~1\ORACLE~1\common\wlst\RESOUR~1\ossoiap.jar;C:\Oracle\MIDDLE~1\ORACLE~1\common\wlst\RESOUR~1\OSSOIA~1.JAR;C:\Oracle\MIDDLE~1\ORACLE~1\common\wlst\RESOUR~1\SSLCON~1.JAR;C:\Oracle\MIDDLE~1\ORACLE~1\common\wlst\RESOUR~1\wsm-wlst.jar;C:\Oracle\MIDDLE~1\WLSERV~1.3\common\eval\pointbase\lib\pbembedded57.jar;C:\Oracle\MIDDLE~1\WLSERV~1.3\common\eval\pointbase\lib\pbclient57.jar;C:\Oracle\MIDDLE~1\WLSERV~1.3\common\eval\pointbase\lib\pbtools57.jar" weblogic.NodeManager "-v"
    Apr 22, 2011 3:23:21 PM oracle.sysman.omsca.util.ProcessOutputReader run
    FINE: NMProcess: <Apr 22, 2011 3:23:21 PM> <INFO> <Loading domains file: C:\Oracle\MIDDLE~1\WLSERV~1.3\common\emnodemanager20110422152239\nodemanager.domains> Apr 22, 2011 3:23:21 PM oracle.sysman.omsca.util.ProcessOutputReader run
    FINE: NMProcess: Apr 22, 2011 3:23:21 PM weblogic.nodemanager.server.NMServerConfig initDomainsMap Apr 22, 2011 3:23:21 PM oracle.sysman.omsca.util.ProcessOutputReader run
    FINE: NMProcess: INFO: Loading domains file: C:\Oracle\MIDDLE~1\WLSERV~1.3\common\emnodemanager20110422152239\nodemanager.domains Apr 22, 2011 3:23:21 PM oracle.sysman.omsca.util.ProcessOutputReader run
    FINE: NMProcess: <Apr 22, 2011 3:23:21 PM> <WARNING> <Domains file not found: C:\Oracle\MIDDLE~1\WLSERV~1.3\common\emnodemanager20110422152239\nodemanager.domains> Apr 22, 2011 3:23:21 PM oracle.sysman.omsca.util.ProcessOutputReader run
    FINE: NMProcess: Apr 22, 2011 3:23:21 PM weblogic.nodemanager.server.NMServerConfig initDomainsMap Apr 22, 2011 3:23:21 PM oracle.sysman.omsca.util.ProcessOutputReader run
    FINE: NMProcess: WARNING: Domains file not found: C:\Oracle\MIDDLE~1\WLSERV~1.3\common\emnodemanager20110422152239\nodemanager.domains Apr 22, 2011 3:23:22 PM oracle.sysman.omsca.util.ProcessOutputReader run
    FINE: NMProcess: <Apr 22, 2011 3:23:22 PM> <INFO> <Loading identity key store: FileName=C:/Oracle/MIDDLE~1/WLSERV~1.3/server\lib\DemoIdentity.jks, Type=jks, PassPhraseUsed=true> Apr 22, 2011 3:23:22 PM oracle.sysman.omsca.util.ProcessOutputReader run
    FINE: NMProcess: Apr 22, 2011 3:23:22 PM weblogic.nodemanager.server.SSLConfig loadKeyStoreConfig Apr 22, 2011 3:23:22 PM oracle.sysman.omsca.util.ProcessOutputReader run
    FINE: NMProcess: INFO: Loading identity key store: FileName=C:/Oracle/MIDDLE~1/WLSERV~1.3/server\lib\DemoIdentity.jks, Type=jks, PassPhraseUsed=true Apr 22, 2011 3:23:23 PM oracle.sysman.omsca.util.ProcessOutputReader run
    FINE: NMProcess: <Apr 22, 2011 3:23:23 PM> <WARNING> <Node manager configuration properties file 'C:\Oracle\MIDDLE~1\WLSERV~1.3\common\emnodemanager20110422152239\nodemanager.properties' not found. Using default settings.> Apr 22, 2011 3:23:23 PM oracle.sysman.omsca.util.ProcessOutputReader run
    FINE: NMProcess: Apr 22, 2011 3:23:23 PM weblogic.nodemanager.server.NMServer <init> Apr 22, 2011 3:23:23 PM oracle.sysman.omsca.util.ProcessOutputReader run
    FINE: NMProcess: WARNING: Node manager configuration properties file 'C:\Oracle\MIDDLE~1\WLSERV~1.3\common\emnodemanager20110422152239\nodemanager.properties' not found. Using default settings. Apr 22, 2011 3:23:23 PM oracle.sysman.omsca.util.ProcessOutputReader run
    FINE: NMProcess: <Apr 22, 2011 3:23:23 PM> <INFO> <Saving node manager configuration properties to 'C:\Oracle\MIDDLE~1\WLSERV~1.3\common\emnodemanager20110422152239\nodemanager.properties'> Apr 22, 2011 3:23:23 PM oracle.sysman.omsca.util.ProcessOutputReader run
    FINE: NMProcess: Apr 22, 2011 3:23:23 PM weblogic.nodemanager.server.NMServer <init> Apr 22, 2011 3:23:23 PM oracle.sysman.omsca.util.ProcessOutputReader run
    FINE: NMProcess: INFO: Saving node manager configuration properties to 'C:\Oracle\MIDDLE~1\WLSERV~1.3\common\emnodemanager20110422152239\nodemanager.properties' Apr 22, 2011 3:23:23 PM oracle.sysman.omsca.util.ProcessOutputReader run
    FINE: NMProcess: Node manager v10.3 Apr 22, 2011 3:23:23 PM oracle.sysman.omsca.util.ProcessOutputReader run
    FINE: NMProcess: Apr 22, 2011 3:23:23 PM oracle.sysman.omsca.util.ProcessOutputReader run
    FINE: NMProcess: Configuration settings: Apr 22, 2011 3:23:23 PM oracle.sysman.omsca.util.ProcessOutputReader run
    FINE: NMProcess: Apr 22, 2011 3:23:23 PM oracle.sysman.omsca.util.ProcessOutputReader run
    FINE: NMProcess: NodeManagerHome=C:\Oracle\MIDDLE~1\WLSERV~1.3\common\emnodemanager20110422152239 Apr 22, 2011 3:23:23 PM oracle.sysman.omsca.util.ProcessOutputReader run
    FINE: NMProcess: ListenAddress=win2008x64-2 Apr 22, 2011 3:23:23 PM oracle.sysman.omsca.util.ProcessOutputReader run
    FINE: NMProcess: ListenPort=7401 Apr 22, 2011 3:23:23 PM oracle.sysman.omsca.util.ProcessOutputReader run
    FINE: NMProcess: ListenBacklog=50 Apr 22, 2011 3:23:23 PM oracle.sysman.omsca.util.ProcessOutputReader run
    FINE: NMProcess: SecureListener=true Apr 22, 2011 3:23:23 PM oracle.sysman.omsca.util.ProcessOutputReader run
    FINE: NMProcess: AuthenticationEnabled=true Apr 22, 2011 3:23:23 PM oracle.sysman.omsca.util.ProcessOutputReader run
    FINE: NMProcess: NativeVersionEnabled=true Apr 22, 2011 3:23:23 PM oracle.sysman.omsca.util.ProcessOutputReader run
    FINE: NMProcess: CrashRecoveryEnabled=false Apr 22, 2011 3:23:23 PM oracle.sysman.omsca.util.ProcessOutputReader run
    FINE: NMProcess: JavaHome=C:\Oracle\MIDDLE~1\JROCKI~1.5-3\jre Apr 22, 2011 3:23:23 PM oracle.sysman.omsca.util.ProcessOutputReader run
    FINE: NMProcess: StartScriptEnabled=true Apr 22, 2011 3:23:23 PM oracle.sysman.omsca.util.ProcessOutputReader run
    FINE: NMProcess: StopScriptEnabled=false Apr 22, 2011 3:23:23 PM oracle.sysman.omsca.util.ProcessOutputReader run
    FINE: NMProcess: StartScriptName=startEMServer.cmd Apr 22, 2011 3:23:23 PM oracle.sysman.omsca.util.ProcessOutputReader run
    FINE: NMProcess: StopScriptName= Apr 22, 2011 3:23:23 PM oracle.sysman.omsca.util.ProcessOutputReader run
    FINE: NMProcess: LogFile=C:\Oracle\MIDDLE~1\WLSERV~1.3\common\emnodemanager20110422152239\nodemanager.log Apr 22, 2011 3:23:23 PM oracle.sysman.omsca.util.ProcessOutputReader run
    FINE: NMProcess: LogLevel=INFO Apr 22, 2011 3:23:23 PM oracle.sysman.omsca.util.ProcessOutputReader run
    FINE: NMProcess: LogLimit=0 Apr 22, 2011 3:23:23 PM oracle.sysman.omsca.util.ProcessOutputReader run
    FINE: NMProcess: LogCount=1 Apr 22, 2011 3:23:23 PM oracle.sysman.omsca.util.ProcessOutputReader run
    FINE: NMProcess: LogAppend=true Apr 22, 2011 3:23:23 PM oracle.sysman.omsca.util.ProcessOutputReader run
    FINE: NMProcess: LogToStderr=true Apr 22, 2011 3:23:23 PM oracle.sysman.omsca.util.ProcessOutputReader run
    FINE: NMProcess: LogFormatter=weblogic.nodemanager.server.LogFormatter Apr 22, 2011 3:23:23 PM oracle.sysman.omsca.util.ProcessOutputReader run
    FINE: NMProcess: DomainsFile=C:\Oracle\MIDDLE~1\WLSERV~1.3\common\emnodemanager20110422152239\nodemanager.domains Apr 22, 2011 3:23:23 PM oracle.sysman.omsca.util.ProcessOutputReader run
    FINE: NMProcess: DomainsFileEnabled=true Apr 22, 2011 3:23:23 PM oracle.sysman.omsca.util.ProcessOutputReader run
    FINE: NMProcess: StateCheckInterval=500 Apr 22, 2011 3:23:23 PM oracle.sysman.omsca.util.ProcessOutputReader run
    FINE: NMProcess: QuitEnabled=true Apr 22, 2011 3:23:23 PM oracle.sysman.omsca.util.ProcessOutputReader run
    FINE: NMProcess: Interface= Apr 22, 2011 3:23:23 PM oracle.sysman.omsca.util.ProcessOutputReader run
    FINE: NMProcess: NetMask= Apr 22, 2011 3:23:23 PM oracle.sysman.omsca.util.ProcessOutputReader run
    FINE: NMProcess: UseMACBroadcast=false Apr 22, 2011 3:23:23 PM oracle.sysman.omsca.util.ProcessOutputReader run
    FINE: NMProcess: DomainRegistrationEnabled=false Apr 22, 2011 3:23:23 PM oracle.sysman.omsca.util.ProcessOutputReader run
    FINE: NMProcess: Apr 22, 2011 3:23:23 PM oracle.sysman.omsca.util.ProcessOutputReader run
    FINE: NMProcess: Domain name mappings: Apr 22, 2011 3:23:23 PM oracle.sysman.omsca.util.ProcessOutputReader run
    FINE: NMProcess: Apr 22, 2011 3:23:23 PM oracle.sysman.omsca.util.ProcessOutputReader run
    FINE: NMProcess: Apr 22, 2011 3:23:23 PM oracle.sysman.omsca.util.ProcessOutputReader run
    FINE: NMProcess: <Apr 22, 2011 3:23:23 PM> <INFO> <Secure socket listener started on port 7,401, host WIN2008x64-2/192.168.182.135> Apr 22, 2011 3:23:23 PM oracle.sysman.omsca.util.ProcessOutputReader run
    FINE: NMProcess: Apr 22, 2011 3:23:23 PM weblogic.nodemanager.server.SSLListener run Apr 22, 2011 3:23:23 PM oracle.sysman.omsca.util.ProcessOutputReader run
    FINE: NMProcess: INFO: Secure socket listener started on port 7,401, host WIN2008x64-2/192.168.182.135 Apr 22, 2011 3:23:30 PM oracle.sysman.omsca.util.ProcessOutputReader run
    FINE: Successfully launched the Node Manager. Apr 22, 2011 3:23:30 PM oracle.sysman.omsca.util.ProcessOutputReader run
    FINE: The Node Manager process is running independent of the WLST process. Apr 22, 2011 3:23:30 PM oracle.sysman.omsca.util.ProcessOutputReader run
    FINE: Exiting WLST will not stop the Node Manager process. Please refer Apr 22, 2011 3:23:30 PM oracle.sysman.omsca.util.ProcessOutputReader run
    FINE: to the Node Manager logs for more information. Apr 22, 2011 3:23:30 PM oracle.sysman.omsca.util.ProcessOutputReader run
    FINE: The Node Manager logs will be under C:\Oracle\MIDDLE~1\WLSERV~1.3\common\emnodemanager20110422152239 Apr 22, 2011 3:23:30 PM oracle.sysman.omsca.util.ProcessOutputReader run
    FINE: Connecting to Node Manager ... Apr 22, 2011 3:23:41 PM oracle.sysman.omsca.util.ProcessOutputReader run
    FINE: NMProcess: <Apr 22, 2011 3:23:41 PM> <WARNING> <Configuration error while reading domain directory> Apr 22, 2011 3:23:41 PM oracle.sysman.omsca.util.ProcessOutputReader run
    FINE: NMProcess: weblogic.nodemanager.common.ConfigException: The domain 'GCDomain' at 'C:\Oracle\gc_inst\user_projects\domains\GCDomain' was not registered in the nodemanager.domains file and dynamic domain registration is not supported. Please register the domain in the nodemanager.domains file. Apr 22, 2011 3:23:41 PM oracle.sysman.omsca.util.ProcessOutputReader run
    FINE: NMProcess:      at weblogic.nodemanager.server.NMServer.getDomainManager(NMServer.java:257) Apr 22, 2011 3:23:41 PM oracle.sysman.omsca.util.ProcessOutputReader run
    FINE: NMProcess:      at weblogic.nodemanager.server.Handler.handleDomain(Handler.java:224) Apr 22, 2011 3:23:41 PM oracle.sysman.omsca.util.ProcessOutputReader run
    FINE: NMProcess:      at weblogic.nodemanager.server.Handler.handleCommand(Handler.java:108) Apr 22, 2011 3:23:41 PM oracle.sysman.omsca.util.ProcessOutputReader run
    FINE: NMProcess:      at weblogic.nodemanager.server.Handler.run(Handler.java:70) Apr 22, 2011 3:23:41 PM oracle.sysman.omsca.util.ProcessOutputReader run
    FINE: NMProcess:      at java.lang.Thread.run(Thread.java:619) Apr 22, 2011 3:23:41 PM oracle.sysman.omsca.util.ProcessOutputReader run
    ...

    I have a JDK already installed, but isn't JRockit being used by NodeManager in this case? Does NodeManager need to run on the JDK?
    Regardless, I tried changing JavaHome in the nodemanager.properties file to the JDK/jre directory, but the log file still has the original path. The log seems to indicate that the process thinks that NodeManager is down because it can't connect, so it launches a new instance and uses default configuration parameters, which naturally wouldn't have my changes to the nodemanager.domain or nodemanager.properties files.
    Also, the log says it can't connect to NodeManager at win2008x64-2:7,401. I'm not sure why there's a comma in there, but by the time this configuration step fails, there is a javaw.exe process listening on port 7401 and if I retry the step without killing it, the step will fail earlier because the port is already bound.

  • Configuration Steps for Decentralized Adapter Engine

    Hi all,
    What all configuration steps are required to make Adapter Engine as
    Decentralized AE.
    I have made required changes in SLD DataSupplier in Visual Administrator.
    what more configurations have to be done? On SAP XI Server and Decentralized
    Adapter Engine.
    With regards
    Prasad

    Prasad,
    After configuring SLD data supplier in Visual Admin, you need to the following
    1) Configure the gateway service for the central integration server on adapter engine host.
    2) Perform Initial adapter engine cache refresh
    3) Trigger data transfer to SLD
    4) Check the connection parameters in exchangeProfile
    5) Create HTTP destination pmistore in java environment
    you have to go through all these tests for decentralized adapter engine. If you have XI configuration guide, it has all these steps in detail for you to configure
    --Archana

  • Risk Mgmnt COnfiguration steps

    Hello Friends
    Can anyone please tell me the complete steps to configure "Risk Management " with LoC (Letter of Credit) & what is the necessary data to be collected from the business, for configuring the same.
    Regards
    Sumanth.Gururaj

    Hi,
    The configuration steps for risk management
    How To Do Configuration For Credit Management
    Credit and risk management takes place in the credit control area. According to your corporate requirements, you can implement credit management that is centralized, decentralized, or somewhere in between. 
    An organizational unit that represents the area where customer credit is awarded and monitored.   This organizational unit can either be a single or several company codes, if credit control is performed across several company codes. One credit control area contains credit control information for each customer.
    For example, if your credit management is centralized, you can define one credit control area for all of your company codes. 
    If, on the other hand, your credit policy requires decentralized credit management, you can define credit control areas for each company code or each group of company codes. 
    Credit limits and credit exposure are managed at both credit control area and customer level.  You set up credit control areas and other data related to credit management in Customizing for Financial Accounting. The implementation guide is under Enterprise Structure -> Definition or Assignment -> Financial Accounting and then Maintain credit control area. You assign customers to specific credit control areas and specify the appropriate credit limits in the customer master record.
    Settings for determining the credit control area of a document.  The settings of items 1 - 4 are taken into account according to their priority.  The credit control area found is stored in field VBAK-KKBER.
    1. Transaction OB38
       Check which credit control area is assigned to the company code.
       Company code:
       Credit control area:
    2. Transaction OVFL
       Check which credit control area is assigned to the sales area.
       Sales area:
       Credit control area:
    3. Transaction XD02 or VD02
       Check which credit control area is assigned to the payer.
       Payer:
       Credit control area:
    4. Transaction SE37
       Is user exit EXIT_SAPV45K_001 being used?
    5. Transaction OBZK
       For the settings under items 2 - 4, field "All company codes" must be marked in Transaction
    OB45, or the credit control area must be entered under the relevant company code in table T001CM of the credit control areas allowed.
    Company code:
    Credit control areas allowed:
    6. Settings for the credit checks
    7. Transaction OVAK
       Which settings do exist for the sales document type used?
       Sales document:
    Check credit:
    Credit group:
    8. Transaction OVAD
       Which settings do exist for the delivery type used?
    Delivery type:
    Credit group for delivery:
    Credit group for goods issue:
    9. Transaction OB01
       Credit management/Change risk category
       Definition of the risk category for each credit control area. This risk category can be assigned to a credit account by using Transaction FD32.
    10. Transaction OVA8
        Here, the individual credit checks for key fields
        o credit control area
        o risk category
        o credit group are set. Take these key fields from the above settings and go to the detail screen. In particular, check whether fields "Reaction" and "Status/block" are set correctly. To carry out follow-up actions in case of a credit block, the credit check status must be set (field "Status/block").
    11. Transaction FD32
        Credit master data for the payer of the relevant document.
        Credit account:
        Credit limit:
        Risk category:
        Currency:
    12. Settings for updating the credit values Update of the credit values is required for the limit check (static or dynamic credit limit check).
    13. Transaction OVA7
        Update of the credit value is active for the corresponding item type if the check box is marked. This field corresponds to 
        field "Active receivable" in Transaction VOV7.
    Item type: 
    Active receivable:
    14. Transaction V/08, Pricing
        In the pricing procedure used for pricing, subtotal "A" must be entered in a line for determining the credit value (mark the pricing procedure and doubleclick on "Control").
    Usually, the net value plus taxes is used. This way the system is determined to use this subtotal for credit pricing. The credit price is stored in field VBAP-CMPRE and used for update and credit check.
    You can find the used pricing procedure of the order under "Item -> Condition -> Analysis".
    Pricing procedure:
    Line with subtotal = 'A':
    15. Transaction OB45
        Which update group (field "Update") do you use in the relevant credit control area? The default setting is "12". If you use another update group, check whether this is fine with you. If you open an OSS message, please tell us the alternative update group.
    Credit control area:
    Update:
    16. Transaction OMO1
        Which kind of update did you choose for structure S066? 
         In any case, "Synchronous update (1)" has to be chosen as the kind of update.  All other settings will lead to errors.
    Credit Management Reports
    The following table provides an overview of all the reports that are available for credit management:
    Program     Function
    RFDKLI10     Customers with Missing Credit Data
    Checks whether the data regarding credit limits is complete and issues relevant error lists. These enable you to maintain the relevant definitions either manually or with batch input.
    RFDKLI20     Reset Credit Limit for Customers
    Resets the credit limit information in the control areas.
    RFDKLI30     Credit Limit Overview
    Lists the central and control area data for each customer.
    RFDKLI40     Credit Overview
    Provides a comprehensive overview of the customeru2019s credit situation.
    RFDKLI41     Credit Master Sheet
    Displays and prints the customer master data for an individual account that is needed for credit management.
    RFDKLI42     Early Warning List
    Displays and prints customers in Credit Management who have been listed by the credit check as critical.
    RFDKLI50     Credit Limit Data Mass Change
    Changes all the credit management master data together.
    RFDKLIAB     Display Changes to Credit Management
    Displays the changes to credit management master data for all accounts.
    RVKRED06     Check Blocked Credit Documents
    Checks all the documents blocked for credit reasons. The report is started in the background and should run after the incoming payments programs.
    RVKRED77     Reorganize SD Credit Data
    Reorganizes open credit, delivery and billing values. It can be used in the event of an update error, for example.
    RVKRED08     Checking sales documents which reach the credit horizon
    Rechecks all sales documents that fall within the credit limit horizon of the dynamic credit limit check. The report is run at regular intervals and should be run at the start of each period. The system uses the current date and the period split for the open order values to propose the u2018next credit check dateu2019.
    RVKRED09     Check Credit Documentation Background
    Checks released documents whose validity period of the release has been exceeded (number of days).
    RVKRED88     Simulating Reorganization of SD Credit Data
    To run a report:
    1.     Choose System ® Services ® Reporting.
    2.     Enter the name of the report.
    3.     Choose Program ® Execute.
    4.     Enter your selection criteria.
    5.     Choose Program ® Execute or Program ® Execute and print.
    SAP SD Credit Management Tcodes
    All business have their own credit management needs, SAP allows you to specify your own automatic credit checks based on a variety of criteria.  You can also specify at which critical points in the sales and distribution cycle the system carries out these checks.
    SM30 - Table/View
    u2022     V_TVTW - Define Distribution Channel
    u2022     V_TVTA_KKB - Assign sales area to credit control area
    u2022     V_T014 - FI - Define Credit Control Area
    u2022     T001CM - FI - Assign Permitted Credit Control Area to company code
    OVXG - Set up Sales Areas
    e.g.  Sales Organization
                      Distribution Channel
                                  Division
                      Distribution Channel
                                  Division
    FD32 - Customer Credit Management
    OVAK - Define credit limit check by sales document type
    u2022     Check Credit
    o     A - Credit limit check and warning message
    o     B - Credit limit check and error message (no sales order can    be created)
    o     C - Credit limit check and delivery block (block delivery if hit   credit limit)
         Options B and C -> used for checking open order values (when you create/change the sales order)
    o     D - Automatic credit control with open order values
         More control in transaction OVA8 - Automatic credit control
         You check for open orders and deliveries, or just open deliveries.
         or open order values with other options
    u2022     Credit group
    o     Allows you to combine different sales document types for the credit limit check
    VKM1 - Blocked SD Documents - Finance have to released the delivery block
    OVAD - Define credit limit check by delivery order
    u2022     whether the automatic credit check occurs at the time of delivery creation and/or goods issue
    OVA7 - Define credit limit check by item category
    u2022     Set whether to include/exclude item category for credit limit check
    OVA6 - Define credit group. You can groups together different business transactions which should be dealt with in the same manner with regard to the credit check.
    You enter the credit groups when you configure the sales document types for credit management and define the (D - automatic credit check).
    u2022     SAP default credit groups
    o     01 - credit group for sales order
    o     02 - credit group for delivery
    o     03 - credit group for goods issue
    OVA8 - Automatic credit control - Double click on the line items
    You can have the followings credit limit check :-
    u2022     Static
    Depends on the customer total value of open orders, deliveries, billing documents and open items.
    u2022     Open items
    No of days open
    Overdue open items checks is based on the ratio of open items that are overdue by a certain number of days.
    Max open items %
    The customer balance must not exceed a certain percentage.
    u2022     Oldest open items
    If you don't want to deliver to the customer at all when even only 1 invoice is overdue.
    Tick the Check for Oldest Open Item and Set the field Days oldest item = 1.
    Dayu2019s oldest item
    No of days allowed for overdue or payment terms.
    Use of the credit checks Oldest Open Item. If a user attempts to alter the order quantity of a released sales document
    that was previously blocked, it would be re-blocked again by the system.  The system only re-blocks the sales document if the new order quantity is above a certain % amount.
    u2022     Released documents are still unchecked
    The preset % is whatever you want to set it as when configuring your automatic credit processing. You enter a deviation % and number of days,eg, you can set it so that an order can be changed by up to 10% within 30 days of original order entry date without it going back on credit block.
    u2022     Next Review Date
    If a customer has a credit limit of 1000 USD, and you would like to restrict this credit limit only to be available in current month (say March). If the document date is in April then the credit limit is zero.
    You can use the "NextReview date" and "Number of days" fields and combined it with the "Last int.review" field in customer credit master "Status" view (FD32).
    VOKR - Display of work list for credit management (configure the display variant)
    SIMPLE CREDIT CHECK:
    Tr.Code - FD32
    It Considers the Doc.Value + Open Items.
    Doc.Value: Sales Order has been saved but not delivered
    Open Item: Sales Order has been saved, Delivered, Billed & Transferred to FI, but not received the payment from the customer.
    Eg: Customer Credit Limit is Rs.1, 00,000/-
    Suppose Doc.Value + Open Item Value is Rs.1,10,000/-
    Here credit limit exceeds then system reacts.
    Options: A) Warning Message
    B) Error Message (Sales Order won't be saved)
    C) Error Message with Delivery Block
    AUTOMATIC CREDIT CHECK: Give extra credit facilities to the particular customer.
    STATIC CREDIT LIMIT DETERMINATION: Checking Group + Risk Category + Credit Control Area.
    A) Credit Checking Groups: Types of Checking Groups.
    01) Sales
    02) Deliveries
    03) Goods Issue
    At all the above 3 levels orders can be blocked.
    B) Risk Category: Based on the risk Categories Company decides how much credit has to give to the customer.
    HIGH RISK (0001) :      LOW CREDIT
    LOW RISK (0002) :      MORE CREDIT
    MEDIUM RISK(0003): AVERAGE CREDIT
    Static Credit Check it checks all these doc value & check with the credit limit
    1) Open Doc.Value / Sales Order Value: Which is save but not delivered
    2) Open Delivery Doc.Value: Which is delivered but not billed
    3) Open Billing Doc.Value: Which is billed but not posted to FI
    4) Open Item: Which is transferred to FI but not received from the customer.
    DYNAMIC CREDIT CHECK:
    1) Open Doc
    2) Open Delivery
    3) Open Billing
    4) Open Items
    5) Horizon Period = Eg.3Months
    Here the System will not consider the above 1,2,3& 4 values for the last 3 months
    Then assign the Sales Doc & Del Documents.
    Sales Doc.Type(OR) + credit Check (0) + Credit Group (01)
    Credit Limit Check for Delivery Type : Del.Type (LF) + Del Credit
    Group (02) + Goods Issue Credit Group (03)
    User Exits For Credit Checks And Risk Management
    Credit Check
    I hope this will resolve your issue
    Thanks
    Anil Hooda

Maybe you are looking for

  • Check for empty table row before adding date

    On the form below, when I click the green + button (far right), a new table row is created with today's date. the user can then enter more text to the right of the date. Problem is when the form is saved and reopened, the text the user enters is dele

  • How to force User login to load a flow

    I want the User login to take them straight to a particular flow - bypassing the Marvel admin functions , select flow etc - Is this possible?

  • Adobe Acrobat Standard - 22002418

    Need to install today and client has lost the media. Is there a download to just the media? If not, what is the method to obtain new media? Thank you.

  • Integration of BW system with R/3 system

    Hi, I have a doubt regarding integration of BW system with R/3 system. Can we integrate both the systems without using NetWeaver-XI, If so how can we integrate them and make the data to be interchaged between both BW and R/3 servers. Can we load both

  • Start managed server in multihomed machine with cluster?

    Hi,           I have problems with starting a remote managed server.           I have a cluster configured with 2 managed servers in the same machine. I added a new managed server but assigned to other machine.           MachineA:           -AdminSer