WLC 2106 Disable 802.11b

Hello,
I am trying to enable more channels in the DCA channel list for 802.11/b/g/n.  However, when i hit apply i get this message:
"802.11b network needs to be disabled to apply changes to DCA."
I do not see a spot to disable B. Would this be something i need to do from the CLI?
THanks!
Seth

Hi,
You ned to disable Radios before doing the above config.. here is the was we do it..
WLC GUI >> Wireless >> 802.11 B/G/N >> Network >> Disable 802.11B/G network setup
Now do the required setup and go back to the same place and enable it.. this will do it for you!!
Lemme know if this answered ur question and please dont forget to rate the usefull posts!!
Regards
Surendra

Similar Messages

  • Disabling 802.11b, what issues to coverage?

    Hi All
    I want to soon disable 802.11b support on our AP 1231 with B/G cards. I want this because I don't like to have 802.11b clients connecting and taking down the speed.
    The question now is, how would our signal coverage change if I put 'power local cck 1' on the device?
    Or I would only allow theese rates:
    6.0 9.0 12.0 18.0 24.0 36.0 48.0 54.0 which are only supported by 802.11g cards.
    Would that change the signal range a lot? Or do you have better ideas to disable 802.11b support?
    Thanks,
    Patrick

    Hi Patrick,
    Here is some info related to disabling 802.11b;
    Q. How can I set the AP so that only IEEE 802.11g clients can connect? I do not want the IEEE 802.11b clients to connect and slow down the wireless network. There is a second, parallel 802.11b network for unsecured clients.
    A. In order for the AP to receive only 802.11g clients, complete these steps in the GUI:
    Go to the Network Interfaces section and click Radio 0-802.11G.
    Click the Settings tab at the top of the Radio 0-802.11G window.
    Choose Disable for these data rates:
    1.0
    2.0
    5.5
    11.0
    Choose Require for all the other data rates. These other data rates are:
    6.0
    9.0
    12.0
    18.0
    24.0
    36.0
    48.0
    54.0
    Click Apply at the bottom of the window.
    From this good doc;
    http://www.cisco.com/en/US/products/hw/wireless/ps430/products_qanda_item09186a008009483e.shtml
    As for coverage; A fundamental rule is that as data rates increase, range decreases. 802.11b uses DSSS to support data rates of 11, 5.5, 2, and 1 Mbps each, with correspondingly longer ranges as the data rates decrease. 802.11g uses OFDM to support data rates of 54, 48, 36, 24, 18, 12, 9, and 6 Mbps each, with correspondingly longer ranges as the data rates decrease. The higher data rates supported by 802.11g result in shorter range than the range supported by the maximum 802.11b data rate. Still, OFDM is a more efficient means of transmission than is DSSS, meaning that at a given range, higher OFDM-based data rates will be supported than DSSS-based data rates (all other things being held constant). That being said your range difference should not be too drastic
    From this superior Cisco doc (Have a look at Table 4 for some good Range approximations);
    http://www.cisco.com/en/US/products/hw/wireless/ps430/products_white_paper09186a00801d61a3.shtml
    Hope this helps!
    Rob

  • Disable 802.11b/g

    Can i disable 802.11b/g in my new Time Capsule that supports 802.11ac? Ultimaltely I want to disable all standards under 802.11ac (when iPhone/iPad finally supports it)
    I have read old wifi standards slows downs routers/acess points etc.

    Can i disable 802.11b/g in my new Time Capsule that supports 802.11ac?
    Sorry, but no.
    Whlle you could customize and maximize previous versions of the Time Capsule, Apple has "upgraded" things by removing the settings that would allow this in the "new" Time Capsule.

  • WRT300n: disable 802.11b wireless

    Is it possible to administratively disable 802.11b radio on WRT300N?
    The reason is to do not allow 802.11b clients to connect to my router, while 802.11g and 802.11n clients should get access to network.
    Solved!
    Go to Solution.

    You cannot disable just 802.11b wireless...When you open the set up page of your router and click on Wireless see the Network Mode...You can disable all or when it is set to mixed it will enable all...When you select Wireless N Only it will disable Wireless B and Wireless G both...Same when you select Wireless G only(it will disable Wireless B and Wireless N both)...This means that you can have two of the modes disabled but not just one...

  • Client got not connection to wlan over wlc 2504 on 802.11b/g

    Hi everybody,
    We are using a wlc 2504 with 7.6.100.0 and AP 1532e.
    I have the strange observacion that only clients with 802.11n (2.4GHz) can connect to the WLAN. Clients thats works only with 802.11b/g, they can't connect to the WLAN. Affected are all machines which want to connect with 802.11b/g.
    This is a MESH WLAN with 5GHz backhaul and 2.4GHz for the user.
    During the debugging found the following:
    *apfMsConnTask_4: May 09 11:44:40.581: 00:1b:77:b4:34:e0 Sending Assoc Response to station on BSSID 18:9c:5d:71:34:50 (status 0) ApVapId 1 Slot 0
    *apfMsConnTask_4: May 09 11:44:40.581: 00:1b:77:b4:34:e0 apfProcessAssocReq (apf_80211.c:8292) Changing state for mobile 00:1b:77:b4:34:e0 on AP 18:9c:5d:71:34:50 from Associated to Associated
    *spamApTask6: May 09 11:44:40.584: 00:1b:77:b4:34:e0 Sent 1x initiate message to multi thread task for mobile 00:1b:77:b4:34:e0
    *Dot1x_NW_MsgTask_0: May 09 11:44:40.584: 00:1b:77:b4:34:e0 Creating a PKC PMKID Cache entry for station 00:1b:77:b4:34:e0 (RSN 2)
    *Dot1x_NW_MsgTask_0: May 09 11:44:40.584: 00:1b:77:b4:34:e0 Resetting MSCB PMK Cache Entry 0 for station 00:1b:77:b4:34:e0
    *Dot1x_NW_MsgTask_0: May 09 11:44:40.584: 00:1b:77:b4:34:e0 Setting active key cache index 8 ---> 8
    *Dot1x_NW_MsgTask_0: May 09 11:44:40.584: 00:1b:77:b4:34:e0 Setting active key cache index 8 ---> 0
    *Dot1x_NW_MsgTask_0: May 09 11:44:40.584: 00:1b:77:b4:34:e0 Adding BSSID 18:9c:5d:71:34:50 to PMKID cache at index 0 for station 00:1b:77:b4:34:e0
    *Dot1x_NW_MsgTask_0: May 09 11:44:40.584: New PMKID: (16)
    *Dot1x_NW_MsgTask_0: May 09 11:44:40.584:      [0000] f6 3d 52 9f 2a de 52 90 1d a2 46 49 0f 14 f6 69
    *Dot1x_NW_MsgTask_0: May 09 11:44:40.584: 00:1b:77:b4:34:e0 Initiating RSN PSK to mobile 00:1b:77:b4:34:e0
    *Dot1x_NW_MsgTask_0: May 09 11:44:40.584: 00:1b:77:b4:34:e0 EAP-PARAM Debug - eap-params for Wlan-Id :1 is disabled - applying Global eap timers and retries
    *Dot1x_NW_MsgTask_0: May 09 11:44:40.584: 00:1b:77:b4:34:e0 dot1x - moving mobile 00:1b:77:b4:34:e0 into Force Auth state
    *Dot1x_NW_MsgTask_0: May 09 11:44:40.584: 00:1b:77:b4:34:e0 EAPOL Header:
    *Dot1x_NW_MsgTask_0: May 09 11:44:40.584: 00000000: 02 03 00 5f                                       ..._
    *Dot1x_NW_MsgTask_0: May 09 11:44:40.584: 00:1b:77:b4:34:e0 Found an cache entry for BSSID 18:9c:5d:71:34:50 in PMKID cache at index 0 of station 00:1b:77:b4:34:e0
    *Dot1x_NW_MsgTask_0: May 09 11:44:40.584: 00:1b:77:b4:34:e0 Found an cache entry for BSSID 18:9c:5d:71:34:50 in PMKID cache at index 0 of station 00:1b:77:b4:34:e0
    *Dot1x_NW_MsgTask_0: May 09 11:44:40.584: Including PMKID in M1  (16)
    *Dot1x_NW_MsgTask_0: May 09 11:44:40.584:      [0000] f6 3d 52 9f 2a de 52 90 1d a2 46 49 0f 14 f6 69
    *Dot1x_NW_MsgTask_0: May 09 11:44:40.584: 00:1b:77:b4:34:e0 Starting key exchange to mobile 00:1b:77:b4:34:e0, data packets will be dropped
    *Dot1x_NW_MsgTask_0: May 09 11:44:40.584: 00:1b:77:b4:34:e0 Sending EAPOL-Key Message to mobile 00:1b:77:b4:34:e0
       state INITPMK (message 1), replay counter 00.00.00.00.00.00.00.00
    *Dot1x_NW_MsgTask_0: May 09 11:44:40.584: 00:1b:77:b4:34:e0 Sending EAPOL-Key Message to mobile 00:1b:77:b4:34:e0
       state INITPMK (message 1), replay counter 00.00.00.00.00.00.00.00
    *Dot1x_NW_MsgTask_0: May 09 11:44:40.584: 00:1b:77:b4:34:e0 Allocating EAP Pkt for retransmission to mobile 00:1b:77:b4:34:e0
    *Dot1x_NW_MsgTask_0: May 09 11:44:40.585: 00:1b:77:b4:34:e0 mscb->apfMsLwappLradNhMac = 78:da:6e:59:c9:8c mscb->apfMsLradSlotId = 0 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
    *Dot1x_NW_MsgTask_0: May 09 11:44:40.585: 00:1b:77:b4:34:e0  mscb->apfMsBssid = 18:9c:5d:71:34:50 mscb->apfMsAddress = 00:1b:77:b4:34:e0 mscb->apfMsApVapId = 1
    *Dot1x_NW_MsgTask_0: May 09 11:44:40.585: 00:1b:77:b4:34:e0  dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 0 mscb->apfMsLwappMwarInet.ipv4.addr = -1062679171
    *Dot1x_NW_MsgTask_0: May 09 11:44:40.585: 00:1b:77:b4:34:e0  mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = -1062679163 mscb->apfMsLwappLradPort = 40089
    *osapiBsnTimer: May 09 11:44:42.649: 00:1b:77:b4:34:e0 802.1x 'timeoutEvt' Timer expired for station 00:1b:77:b4:34:e0 and for message = M2
    *dot1xMsgTask: May 09 11:44:42.649: 00:1b:77:b4:34:e0 Retransmit 1 of EAPOL-Key M1 (length 121) for mobile 00:1b:77:b4:34:e0
    *dot1xMsgTask: May 09 11:44:42.649: 00:1b:77:b4:34:e0 mscb->apfMsLwappLradNhMac = 78:da:6e:59:c9:8c mscb->apfMsLradSlotId = 0 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
    *dot1xMsgTask: May 09 11:44:42.649: 00:1b:77:b4:34:e0  mscb->apfMsBssid = 18:9c:5d:71:34:50 mscb->apfMsAddress = 00:1b:77:b4:34:e0 mscb->apfMsApVapId = 1
    *dot1xMsgTask: May 09 11:44:42.649: 00:1b:77:b4:34:e0  dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 0 mscb->apfMsLwappMwarInet.ipv4.addr = -1062679171
    *dot1xMsgTask: May 09 11:44:42.649: 00:1b:77:b4:34:e0  mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = -1062679163 mscb->apfMsLwappLradPort = 40089
    *osapiBsnTimer: May 09 11:44:44.649: 00:1b:77:b4:34:e0 802.1x 'timeoutEvt' Timer expired for station 00:1b:77:b4:34:e0 and for message = M2
    *dot1xMsgTask: May 09 11:44:44.649: 00:1b:77:b4:34:e0 Retransmit 2 of EAPOL-Key M1 (length 121) for mobile 00:1b:77:b4:34:e0
    *dot1xMsgTask: May 09 11:44:44.649: 00:1b:77:b4:34:e0 mscb->apfMsLwappLradNhMac = 78:da:6e:59:c9:8c mscb->apfMsLradSlotId = 0 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
    *dot1xMsgTask: May 09 11:44:44.649: 00:1b:77:b4:34:e0  mscb->apfMsBssid = 18:9c:5d:71:34:50 mscb->apfMsAddress = 00:1b:77:b4:34:e0 mscb->apfMsApVapId = 1
    *dot1xMsgTask: May 09 11:44:44.649: 00:1b:77:b4:34:e0  dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 0 mscb->apfMsLwappMwarInet.ipv4.addr = -1062679171
    *dot1xMsgTask: May 09 11:44:44.650: 00:1b:77:b4:34:e0  mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = -1062679163 mscb->apfMsLwappLradPort = 40089
    *osapiBsnTimer: May 09 11:44:46.649: 00:1b:77:b4:34:e0 802.1x 'timeoutEvt' Timer expired for station 00:1b:77:b4:34:e0 and for message = M2
    *dot1xMsgTask: May 09 11:44:46.649: 00:1b:77:b4:34:e0 Retransmit failure for EAPOL-Key M1 to mobile 00:1b:77:b4:34:e0, retransmit count 3, mscb deauth count 1
    *dot1xMsgTask: May 09 11:44:46.649: 00:1b:77:b4:34:e0 Resetting MSCB PMK Cache Entry 0 for station 00:1b:77:b4:34:e0
    *dot1xMsgTask: May 09 11:44:46.649: 00:1b:77:b4:34:e0 Removing BSSID 18:9c:5d:71:34:50 from PMKID cache of station 00:1b:77:b4:34:e0
    *dot1xMsgTask: May 09 11:44:46.649: 00:1b:77:b4:34:e0 Setting active key cache index 0 ---> 8
    *dot1xMsgTask: May 09 11:44:46.649: 00:1b:77:b4:34:e0 Sent Deauthenticate to mobile on BSSID 18:9c:5d:71:34:50 slot 0(caller 1x_ptsm.c:598)
    *dot1xMsgTask: May 09 11:44:46.649: 00:1b:77:b4:34:e0 Setting active key cache index 8 ---> 8
    *dot1xMsgTask: May 09 11:44:46.649: 00:1b:77:b4:34:e0 Deleting the PMK cache when de-authenticating the client.
    *dot1xMsgTask: May 09 11:44:46.649: 00:1b:77:b4:34:e0 Global PMK Cache deletion failed.
    *dot1xMsgTask: May 09 11:44:46.649: 00:1b:77:b4:34:e0 Scheduling deletion of Mobile Station:  (callerId: 57) in 10 seconds
    *dot1xMsgTask: May 09 11:44:46.649: 00:1b:77:b4:34:e0 Freeing EAP Retransmit Bufer for mobile 00:1b:77:b4:34:e0
    *apfMsConnTask_4: May 09 11:44:52.083: 00:1b:77:b4:34:e0 Reassociation received from mobile on BSSID 18:9c:5d:71:34:50
    *apfMsConnTask_4: May 09 11:44:52.083: 00:1b:77:b4:34:e0 Global 200 Clients are allowed to AP radio
    *apfMsConnTask_4: May 09 11:44:52.083: 00:1b:77:b4:34:e0 Max Client Trap Threshold: 0  cur: 1
    *apfMsConnTask_4: May 09 11:44:52.083: 00:1b:77:b4:34:e0 Rf profile 600 Clients are allowed to AP wlan
    *apfMsConnTask_4: May 09 11:44:52.083: 00:1b:77:b4:34:e0 Applying Interface policy on Mobile, role Unassociated. Ms NAC State 2 Quarantine Vlan 0 Access Vlan 1
    *apfMsConnTask_4: May 09 11:44:52.083: 00:1b:77:b4:34:e0 Re-applying interface policy for client
    *apfMsConnTask_4: May 09 11:44:52.083: 00:1b:77:b4:34:e0 0.0.0.0 START (0) Changing IPv4 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2202)
    *apfMsConnTask_4: May 09 11:44:52.083: 00:1b:77:b4:34:e0 0.0.0.0 START (0) Changing IPv6 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2223)
    *apfMsConnTask_4: May 09 11:44:52.083: 00:1b:77:b4:34:e0 apfApplyWlanPolicy: Apply WLAN Policy over PMIPv6 Client Mobility Type
    *apfMsConnTask_4: May 09 11:44:52.083: 00:1b:77:b4:34:e0 In processSsidIE:4795 setting Central switched to TRUE
    *apfMsConnTask_4: May 09 11:44:52.083: 00:1b:77:b4:34:e0 In processSsidIE:4798 apVapId = 1 and Split Acl Id = 65535
    *apfMsConnTask_4: May 09 11:44:52.083: 00:1b:77:b4:34:e0 Applying site-specific Local Bridging override for station 00:1b:77:b4:34:e0 - vapId 1, site 'default-group', interface 'catodos'
    *apfMsConnTask_4: May 09 11:44:52.083: 00:1b:77:b4:34:e0 Applying Local Bridging Interface Policy for station 00:1b:77:b4:34:e0 - vlan 1, interface id 12, interface 'catodos'
    *apfMsConnTask_4: May 09 11:44:52.083: 00:1b:77:b4:34:e0 processSsidIE  statusCode is 0 and status is 0
    *apfMsConnTask_4: May 09 11:44:52.083: 00:1b:77:b4:34:e0 processSsidIE  ssid_done_flag is 0 finish_flag is 0
    *apfMsConnTask_4: May 09 11:44:52.083: 00:1b:77:b4:34:e0 STA - rates (8): 2 4 11 22 12 18 24 36 48 72 96 108 0 0 0 0
    *apfMsConnTask_4: May 09 11:44:52.083: 00:1b:77:b4:34:e0 suppRates  statusCode is 0 and gotSuppRatesElement is 1
    *apfMsConnTask_4: May 09 11:44:52.083: 00:1b:77:b4:34:e0 STA - rates (12): 2 4 11 22 12 18 24 36 48 72 96 108 0 0 0 0
    *apfMsConnTask_4: May 09 11:44:52.083: 00:1b:77:b4:34:e0 extSuppRates  statusCode is 0 and gotExtSuppRatesElement is 1
    *apfMsConnTask_4: May 09 11:44:52.083: 00:1b:77:b4:34:e0 Processing RSN IE type 48, length 20 for mobile 00:1b:77:b4:34:e0
    *apfMsConnTask_4: May 09 11:44:52.083: 00:1b:77:b4:34:e0 0.0.0.0 START (0) Initializing policy
    *apfMsConnTask_4: May 09 11:44:52.084: 00:1b:77:b4:34:e0 0.0.0.0 START (0) Change state to AUTHCHECK (2) last state START (0)
    *apfMsConnTask_4: May 09 11:44:52.084: 00:1b:77:b4:34:e0 0.0.0.0 AUTHCHECK (2) Change state to 8021X_REQD (3) last state AUTHCHECK (2)
    *apfMsConnTask_4: May 09 11:44:52.084: 00:1b:77:b4:34:e0 Central switch is TRUE
    *apfMsConnTask_4: May 09 11:44:52.084: 00:1b:77:b4:34:e0 Not Using WMM Compliance code qosCap 00
    *apfMsConnTask_4: May 09 11:44:52.084: 00:1b:77:b4:34:e0 0.0.0.0 8021X_REQD (3) Plumbed mobile LWAPP rule on AP 18:9c:5d:71:34:50 vapId 1 apVapId 1 flex-acl-name:
    *apfMsConnTask_4: May 09 11:44:52.084: 00:1b:77:b4:34:e0 apfPemAddUser2 (apf_policy.c:333) Changing state for mobile 00:1b:77:b4:34:e0 on AP 18:9c:5d:71:34:50 from Associated to Associated
    *apfMsConnTask_4: May 09 11:44:52.084: 00:1b:77:b4:34:e0 apfPemAddUser2:session timeout forstation 00:1b:77:b4:34:e0 - Session Tout 1800, apfMsTimeOut '1800' and sessionTimerRunning flag is  0
    *apfMsConnTask_4: May 09 11:44:52.084: 00:1b:77:b4:34:e0 Scheduling deletion of Mobile Station:  (callerId: 49) in 1800 seconds
    *apfMsConnTask_4: May 09 11:44:52.084: 00:1b:77:b4:34:e0 Func: apfPemAddUser2, Ms Timeout = 1800, Session Timeout = 1800
    *apfMsConnTask_4: May 09 11:44:52.084: 00:1b:77:b4:34:e0 Sending Assoc Response to station on BSSID 18:9c:5d:71:34:50 (status 0) ApVapId 1 Slot 0
    *apfMsConnTask_4: May 09 11:44:52.084: 00:1b:77:b4:34:e0 apfProcessAssocReq (apf_80211.c:8292) Changing state for mobile 00:1b:77:b4:34:e0 on AP 18:9c:5d:71:34:50 from Associated to Associated
    *spamApTask6: May 09 11:44:52.087: 00:1b:77:b4:34:e0 Sent 1x initiate message to multi thread task for mobile 00:1b:77:b4:34:e0
    *Dot1x_NW_MsgTask_0: May 09 11:44:52.087: 00:1b:77:b4:34:e0 Creating a PKC PMKID Cache entry for station 00:1b:77:b4:34:e0 (RSN 2)
    *Dot1x_NW_MsgTask_0: May 09 11:44:52.087: 00:1b:77:b4:34:e0 Resetting MSCB PMK Cache Entry 0 for station 00:1b:77:b4:34:e0
    *Dot1x_NW_MsgTask_0: May 09 11:44:52.087: 00:1b:77:b4:34:e0 Setting active key cache index 8 ---> 8
    *Dot1x_NW_MsgTask_0: May 09 11:44:52.087: 00:1b:77:b4:34:e0 Setting active key cache index 8 ---> 0
    *Dot1x_NW_MsgTask_0: May 09 11:44:52.087: 00:1b:77:b4:34:e0 Adding BSSID 18:9c:5d:71:34:50 to PMKID cache at index 0 for station 00:1b:77:b4:34:e0
    *Dot1x_NW_MsgTask_0: May 09 11:44:52.087: New PMKID: (16)
    *Dot1x_NW_MsgTask_0: May 09 11:44:52.087:      [0000] f6 3d 52 9f 2a de 52 90 1d a2 46 49 0f 14 f6 69
    *Dot1x_NW_MsgTask_0: May 09 11:44:52.087: 00:1b:77:b4:34:e0 Initiating RSN PSK to mobile 00:1b:77:b4:34:e0
    *Dot1x_NW_MsgTask_0: May 09 11:44:52.087: 00:1b:77:b4:34:e0 EAP-PARAM Debug - eap-params for Wlan-Id :1 is disabled - applying Global eap timers and retries
    *Dot1x_NW_MsgTask_0: May 09 11:44:52.087: 00:1b:77:b4:34:e0 dot1x - moving mobile 00:1b:77:b4:34:e0 into Force Auth state
    *Dot1x_NW_MsgTask_0: May 09 11:44:52.087: 00:1b:77:b4:34:e0 EAPOL Header:
    *Dot1x_NW_MsgTask_0: May 09 11:44:52.087: 00000000: 02 03 00 5f                                       ..._
    *Dot1x_NW_MsgTask_0: May 09 11:44:52.087: 00:1b:77:b4:34:e0 Found an cache entry for BSSID 18:9c:5d:71:34:50 in PMKID cache at index 0 of station 00:1b:77:b4:34:e0
    *Dot1x_NW_MsgTask_0: May 09 11:44:52.087: 00:1b:77:b4:34:e0 Found an cache entry for BSSID 18:9c:5d:71:34:50 in PMKID cache at index 0 of station 00:1b:77:b4:34:e0
    *Dot1x_NW_MsgTask_0: May 09 11:44:52.087: Including PMKID in M1  (16)
    *Dot1x_NW_MsgTask_0: May 09 11:44:52.087:      [0000] f6 3d 52 9f 2a de 52 90 1d a2 46 49 0f 14 f6 69
    *Dot1x_NW_MsgTask_0: May 09 11:44:52.087: 00:1b:77:b4:34:e0 Starting key exchange to mobile 00:1b:77:b4:34:e0, data packets will be dropped
    *Dot1x_NW_MsgTask_0: May 09 11:44:52.087: 00:1b:77:b4:34:e0 Sending EAPOL-Key Message to mobile 00:1b:77:b4:34:e0
       state INITPMK (message 1), replay counter 00.00.00.00.00.00.00.00
    *Dot1x_NW_MsgTask_0: May 09 11:44:52.087: 00:1b:77:b4:34:e0 Sending EAPOL-Key Message to mobile 00:1b:77:b4:34:e0
       state INITPMK (message 1), replay counter 00.00.00.00.00.00.00.00
    *Dot1x_NW_MsgTask_0: May 09 11:44:52.087: 00:1b:77:b4:34:e0 Allocating EAP Pkt for retransmission to mobile 00:1b:77:b4:34:e0
    *Dot1x_NW_MsgTask_0: May 09 11:44:52.087: 00:1b:77:b4:34:e0 mscb->apfMsLwappLradNhMac = 78:da:6e:59:c9:8c mscb->apfMsLradSlotId = 0 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
    *Dot1x_NW_MsgTask_0: May 09 11:44:52.087: 00:1b:77:b4:34:e0  mscb->apfMsBssid = 18:9c:5d:71:34:50 mscb->apfMsAddress = 00:1b:77:b4:34:e0 mscb->apfMsApVapId = 1
    *Dot1x_NW_MsgTask_0: May 09 11:44:52.087: 00:1b:77:b4:34:e0  dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 0 mscb->apfMsLwappMwarInet.ipv4.addr = -1062679171
    *Dot1x_NW_MsgTask_0: May 09 11:44:52.087: 00:1b:77:b4:34:e0  mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = -1062679163 mscb->apfMsLwappLradPort = 40089
    *osapiBsnTimer: May 09 11:44:54.249: 00:1b:77:b4:34:e0 802.1x 'timeoutEvt' Timer expired for station 00:1b:77:b4:34:e0 and for message = M2
    *dot1xMsgTask: May 09 11:44:54.249: 00:1b:77:b4:34:e0 Retransmit 1 of EAPOL-Key M1 (length 121) for mobile 00:1b:77:b4:34:e0
    *dot1xMsgTask: May 09 11:44:54.249: 00:1b:77:b4:34:e0 mscb->apfMsLwappLradNhMac = 78:da:6e:59:c9:8c mscb->apfMsLradSlotId = 0 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
    *dot1xMsgTask: May 09 11:44:54.249: 00:1b:77:b4:34:e0  mscb->apfMsBssid = 18:9c:5d:71:34:50 mscb->apfMsAddress = 00:1b:77:b4:34:e0 mscb->apfMsApVapId = 1
    *dot1xMsgTask: May 09 11:44:54.249: 00:1b:77:b4:34:e0  dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 0 mscb->apfMsLwappMwarInet.ipv4.addr = -1062679171
    *dot1xMsgTask: May 09 11:44:54.249: 00:1b:77:b4:34:e0  mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = -1062679163 mscb->apfMsLwappLradPort = 40089
    *osapiBsnTimer: May 09 11:44:56.249: 00:1b:77:b4:34:e0 802.1x 'timeoutEvt' Timer expired for station 00:1b:77:b4:34:e0 and for message = M2
    *dot1xMsgTask: May 09 11:44:56.249: 00:1b:77:b4:34:e0 Retransmit 2 of EAPOL-Key M1 (length 121) for mobile 00:1b:77:b4:34:e0
    *dot1xMsgTask: May 09 11:44:56.249: 00:1b:77:b4:34:e0 mscb->apfMsLwappLradNhMac = 78:da:6e:59:c9:8c mscb->apfMsLradSlotId = 0 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
    *dot1xMsgTask: May 09 11:44:56.249: 00:1b:77:b4:34:e0  mscb->apfMsBssid = 18:9c:5d:71:34:50 mscb->apfMsAddress = 00:1b:77:b4:34:e0 mscb->apfMsApVapId = 1
    *dot1xMsgTask: May 09 11:44:56.249: 00:1b:77:b4:34:e0  dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 0 mscb->apfMsLwappMwarInet.ipv4.addr = -1062679171
    *dot1xMsgTask: May 09 11:44:56.249: 00:1b:77:b4:34:e0  mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = -1062679163 mscb->apfMsLwappLradPort = 40089
    *osapiBsnTimer: May 09 11:44:58.249: 00:1b:77:b4:34:e0 802.1x 'timeoutEvt' Timer expired for station 00:1b:77:b4:34:e0 and for message = M2
    *dot1xMsgTask: May 09 11:44:58.249: 00:1b:77:b4:34:e0 Retransmit failure for EAPOL-Key M1 to mobile 00:1b:77:b4:34:e0, retransmit count 3, mscb deauth count 2
    *dot1xMsgTask: May 09 11:44:58.249: 00:1b:77:b4:34:e0 Resetting MSCB PMK Cache Entry 0 for station 00:1b:77:b4:34:e0
    *dot1xMsgTask: May 09 11:44:58.249: 00:1b:77:b4:34:e0 Removing BSSID 18:9c:5d:71:34:50 from PMKID cache of station 00:1b:77:b4:34:e0
    *dot1xMsgTask: May 09 11:44:58.249: 00:1b:77:b4:34:e0 Setting active key cache index 0 ---> 8
    *dot1xMsgTask: May 09 11:44:58.250: 00:1b:77:b4:34:e0 Sent Deauthenticate to mobile on BSSID 18:9c:5d:71:34:50 slot 0(caller 1x_ptsm.c:598)
    *dot1xMsgTask: May 09 11:44:58.250: 00:1b:77:b4:34:e0 Setting active key cache index 8 ---> 8
    *dot1xMsgTask: May 09 11:44:58.250: 00:1b:77:b4:34:e0 Deleting the PMK cache when de-authenticating the client.
    *dot1xMsgTask: May 09 11:44:58.250: 00:1b:77:b4:34:e0 Global PMK Cache deletion failed.
    *dot1xMsgTask: May 09 11:44:58.250: 00:1b:77:b4:34:e0 Scheduling deletion of Mobile Station:  (callerId: 57) in 10 seconds
    *dot1xMsgTask: May 09 11:44:58.250: 00:1b:77:b4:34:e0 Freeing EAP Retransmit Bufer for mobile 00:1b:77:b4:34:e0
    *apfMsConnTask_4: May 09 11:45:03.768: 00:1b:77:b4:34:e0 Reassociation received from mobile on BSSID 18:9c:5d:71:34:50
    *apfMsConnTask_4: May 09 11:45:03.768: 00:1b:77:b4:34:e0 Global 200 Clients are allowed to AP radio
    *apfMsConnTask_4: May 09 11:45:03.769: 00:1b:77:b4:34:e0 Max Client Trap Threshold: 0  cur: 1
    *apfMsConnTask_4: May 09 11:45:03.769: 00:1b:77:b4:34:e0 Rf profile 600 Clients are allowed to AP wlan
    *apfMsConnTask_4: May 09 11:45:03.769: 00:1b:77:b4:34:e0 Applying Interface policy on Mobile, role Unassociated. Ms NAC State 2 Quarantine Vlan 0 Access Vlan 1
    *apfMsConnTask_4: May 09 11:45:03.769: 00:1b:77:b4:34:e0 Re-applying interface policy for client
    *apfMsConnTask_4: May 09 11:45:03.769: 00:1b:77:b4:34:e0 0.0.0.0 START (0) Changing IPv4 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2202)
    *apfMsConnTask_4: May 09 11:45:03.769: 00:1b:77:b4:34:e0 0.0.0.0 START (0) Changing IPv6 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2223)
    *apfMsConnTask_4: May 09 11:45:03.769: 00:1b:77:b4:34:e0 apfApplyWlanPolicy: Apply WLAN Policy over PMIPv6 Client Mobility Type
    *apfMsConnTask_4: May 09 11:45:03.769: 00:1b:77:b4:34:e0 In processSsidIE:4795 setting Central switched to TRUE
    *apfMsConnTask_4: May 09 11:45:03.769: 00:1b:77:b4:34:e0 In processSsidIE:4798 apVapId = 1 and Split Acl Id = 65535
    *apfMsConnTask_4: May 09 11:45:03.769: 00:1b:77:b4:34:e0 Applying site-specific Local Bridging override for station 00:1b:77:b4:34:e0 - vapId 1, site 'default-group', interface 'catodos'
    *apfMsConnTask_4: May 09 11:45:03.769: 00:1b:77:b4:34:e0 Applying Local Bridging Interface Policy for station 00:1b:77:b4:34:e0 - vlan 1, interface id 12, interface 'catodos'
    *apfMsConnTask_4: May 09 11:45:03.769: 00:1b:77:b4:34:e0 processSsidIE  statusCode is 0 and status is 0
    *apfMsConnTask_4: May 09 11:45:03.769: 00:1b:77:b4:34:e0 processSsidIE  ssid_done_flag is 0 finish_flag is 0
    *apfMsConnTask_4: May 09 11:45:03.769: 00:1b:77:b4:34:e0 STA - rates (8): 2 4 11 22 12 18 24 36 48 72 96 108 0 0 0 0
    *apfMsConnTask_4: May 09 11:45:03.769: 00:1b:77:b4:34:e0 suppRates  statusCode is 0 and gotSuppRatesElement is 1
    *apfMsConnTask_4: May 09 11:45:03.769: 00:1b:77:b4:34:e0 STA - rates (12): 2 4 11 22 12 18 24 36 48 72 96 108 0 0 0 0
    *apfMsConnTask_4: May 09 11:45:03.769: 00:1b:77:b4:34:e0 extSuppRates  statusCode is 0 and gotExtSuppRatesElement is 1
    *apfMsConnTask_4: May 09 11:45:03.769: 00:1b:77:b4:34:e0 Processing RSN IE type 48, length 20 for mobile 00:1b:77:b4:34:e0
    *apfMsConnTask_4: May 09 11:45:03.769: 00:1b:77:b4:34:e0 0.0.0.0 START (0) Initializing policy
    *apfMsConnTask_4: May 09 11:45:03.769: 00:1b:77:b4:34:e0 0.0.0.0 START (0) Change state to AUTHCHECK (2) last state START (0)
    *apfMsConnTask_4: May 09 11:45:03.769: 00:1b:77:b4:34:e0 0.0.0.0 AUTHCHECK (2) Change state to 8021X_REQD (3) last state AUTHCHECK (2)
    *apfMsConnTask_4: May 09 11:45:03.769: 00:1b:77:b4:34:e0 Central switch is TRUE
    *apfMsConnTask_4: May 09 11:45:03.769: 00:1b:77:b4:34:e0 Not Using WMM Compliance code qosCap 00
    *apfMsConnTask_4: May 09 11:45:03.770: 00:1b:77:b4:34:e0 0.0.0.0 8021X_REQD (3) Plumbed mobile LWAPP rule on AP 18:9c:5d:71:34:50 vapId 1 apVapId 1 flex-acl-name:
    *apfMsConnTask_4: May 09 11:45:03.770: 00:1b:77:b4:34:e0 apfPemAddUser2 (apf_policy.c:333) Changing state for mobile 00:1b:77:b4:34:e0 on AP 18:9c:5d:71:34:50 from Associated to Associated
    *apfMsConnTask_4: May 09 11:45:03.770: 00:1b:77:b4:34:e0 apfPemAddUser2:session timeout forstation 00:1b:77:b4:34:e0 - Session Tout 1800, apfMsTimeOut '1800' and sessionTimerRunning flag is  0
    *apfMsConnTask_4: May 09 11:45:03.770: 00:1b:77:b4:34:e0 Scheduling deletion of Mobile Station:  (callerId: 49) in 1800 seconds
    *apfMsConnTask_4: May 09 11:45:03.770: 00:1b:77:b4:34:e0 Func: apfPemAddUser2, Ms Timeout = 1800, Session Timeout = 1800
    *apfMsConnTask_4: May 09 11:45:03.770: 00:1b:77:b4:34:e0 Sending Assoc Response to station on BSSID 18:9c:5d:71:34:50 (status 0) ApVapId 1 Slot 0
    *apfMsConnTask_4: May 09 11:45:03.770: 00:1b:77:b4:34:e0 apfProcessAssocReq (apf_80211.c:8292) Changing state for mobile 00:1b:77:b4:34:e0 on AP 18:9c:5d:71:34:50 from Associated to Associated
    *spamApTask6: May 09 11:45:03.772: 00:1b:77:b4:34:e0 Sent 1x initiate message to multi thread task for mobile 00:1b:77:b4:34:e0
    *Dot1x_NW_MsgTask_0: May 09 11:45:03.773: 00:1b:77:b4:34:e0 Creating a PKC PMKID Cache entry for station 00:1b:77:b4:34:e0 (RSN 2)
    *Dot1x_NW_MsgTask_0: May 09 11:45:03.773: 00:1b:77:b4:34:e0 Resetting MSCB PMK Cache Entry 0 for station 00:1b:77:b4:34:e0
    *Dot1x_NW_MsgTask_0: May 09 11:45:03.773: 00:1b:77:b4:34:e0 Setting active key cache index 8 ---> 8
    *Dot1x_NW_MsgTask_0: May 09 11:45:03.773: 00:1b:77:b4:34:e0 Setting active key cache index 8 ---> 0
    *Dot1x_NW_MsgTask_0: May 09 11:45:03.773: 00:1b:77:b4:34:e0 Adding BSSID 18:9c:5d:71:34:50 to PMKID cache at index 0 for station 00:1b:77:b4:34:e0
    *Dot1x_NW_MsgTask_0: May 09 11:45:03.773: New PMKID: (16)
    *Dot1x_NW_MsgTask_0: May 09 11:45:03.773:      [0000] f6 3d 52 9f 2a de 52 90 1d a2 46 49 0f 14 f6 69
    *Dot1x_NW_MsgTask_0: May 09 11:45:03.773: 00:1b:77:b4:34:e0 Initiating RSN PSK to mobile 00:1b:77:b4:34:e0
    *Dot1x_NW_MsgTask_0: May 09 11:45:03.773: 00:1b:77:b4:34:e0 EAP-PARAM Debug - eap-params for Wlan-Id :1 is disabled - applying Global eap timers and retries
    *Dot1x_NW_MsgTask_0: May 09 11:45:03.773: 00:1b:77:b4:34:e0 dot1x - moving mobile 00:1b:77:b4:34:e0 into Force Auth state
    *Dot1x_NW_MsgTask_0: May 09 11:45:03.773: 00:1b:77:b4:34:e0 EAPOL Header:
    *Dot1x_NW_MsgTask_0: May 09 11:45:03.773: 00000000: 02 03 00 5f                                       ..._
    *Dot1x_NW_MsgTask_0: May 09 11:45:03.773: 00:1b:77:b4:34:e0 Found an cache entry for BSSID 18:9c:5d:71:34:50 in PMKID cache at index 0 of station 00:1b:77:b4:34:e0
    *Dot1x_NW_MsgTask_0: May 09 11:45:03.773: 00:1b:77:b4:34:e0 Found an cache entry for BSSID 18:9c:5d:71:34:50 in PMKID cache at index 0 of station 00:1b:77:b4:34:e0
    *Dot1x_NW_MsgTask_0: May 09 11:45:03.773: Including PMKID in M1  (16)
    *Dot1x_NW_MsgTask_0: May 09 11:45:03.773:      [0000] f6 3d 52 9f 2a de 52 90 1d a2 46 49 0f 14 f6 69
    *Dot1x_NW_MsgTask_0: May 09 11:45:03.773: 00:1b:77:b4:34:e0 Starting key exchange to mobile 00:1b:77:b4:34:e0, data packets will be dropped
    *Dot1x_NW_MsgTask_0: May 09 11:45:03.773: 00:1b:77:b4:34:e0 Sending EAPOL-Key Message to mobile 00:1b:77:b4:34:e0
       state INITPMK (message 1), replay counter 00.00.00.00.00.00.00.00
    *Dot1x_NW_MsgTask_0: May 09 11:45:03.773: 00:1b:77:b4:34:e0 Sending EAPOL-Key Message to mobile 00:1b:77:b4:34:e0
       state INITPMK (message 1), replay counter 00.00.00.00.00.00.00.00
    *Dot1x_NW_MsgTask_0: May 09 11:45:03.773: 00:1b:77:b4:34:e0 Allocating EAP Pkt for retransmission to mobile 00:1b:77:b4:34:e0
    *Dot1x_NW_MsgTask_0: May 09 11:45:03.773: 00:1b:77:b4:34:e0 mscb->apfMsLwappLradNhMac = 78:da:6e:59:c9:8c mscb->apfMsLradSlotId = 0 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
    *Dot1x_NW_MsgTask_0: May 09 11:45:03.773: 00:1b:77:b4:34:e0  mscb->apfMsBssid = 18:9c:5d:71:34:50 mscb->apfMsAddress = 00:1b:77:b4:34:e0 mscb->apfMsApVapId = 1
    *Dot1x_NW_MsgTask_0: May 09 11:45:03.773: 00:1b:77:b4:34:e0  dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 0 mscb->apfMsLwappMwarInet.ipv4.addr = -1062679171
    *Dot1x_NW_MsgTask_0: May 09 11:45:03.773: 00:1b:77:b4:34:e0  mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = -1062679163 mscb->apfMsLwappLradPort = 40089
    *osapiBsnTimer: May 09 11:45:05.849: 00:1b:77:b4:34:e0 802.1x 'timeoutEvt' Timer expired for station 00:1b:77:b4:34:e0 and for message = M2
    *dot1xMsgTask: May 09 11:45:05.849: 00:1b:77:b4:34:e0 Retransmit 1 of EAPOL-Key M1 (length 121) for mobile 00:1b:77:b4:34:e0
    *dot1xMsgTask: May 09 11:45:05.849: 00:1b:77:b4:34:e0 mscb->apfMsLwappLradNhMac = 78:da:6e:59:c9:8c mscb->apfMsLradSlotId = 0 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
    *dot1xMsgTask: May 09 11:45:05.849: 00:1b:77:b4:34:e0  mscb->apfMsBssid = 18:9c:5d:71:34:50 mscb->apfMsAddress = 00:1b:77:b4:34:e0 mscb->apfMsApVapId = 1
    *dot1xMsgTask: May 09 11:45:05.849: 00:1b:77:b4:34:e0  dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 0 mscb->apfMsLwappMwarInet.ipv4.addr = -1062679171
    *dot1xMsgTask: May 09 11:45:05.849: 00:1b:77:b4:34:e0  mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = -1062679163 mscb->apfMsLwappLradPort = 40089
    *osapiBsnTimer: May 09 11:45:07.848: 00:1b:77:b4:34:e0 802.1x 'timeoutEvt' Timer expired for station 00:1b:77:b4:34:e0 and for message = M2
    *dot1xMsgTask: May 09 11:45:07.849: 00:1b:77:b4:34:e0 Retransmit 2 of EAPOL-Key M1 (length 121) for mobile 00:1b:77:b4:34:e0
    *dot1xMsgTask: May 09 11:45:07.849: 00:1b:77:b4:34:e0 mscb->apfMsLwappLradNhMac = 78:da:6e:59:c9:8c mscb->apfMsLradSlotId = 0 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
    *dot1xMsgTask: May 09 11:45:07.849: 00:1b:77:b4:34:e0  mscb->apfMsBssid = 18:9c:5d:71:34:50 mscb->apfMsAddress = 00:1b:77:b4:34:e0 mscb->apfMsApVapId = 1
    *dot1xMsgTask: May 09 11:45:07.849: 00:1b:77:b4:34:e0  dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 0 mscb->apfMsLwappMwarInet.ipv4.addr = -1062679171
    *dot1xMsgTask: May 09 11:45:07.849: 00:1b:77:b4:34:e0  mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = -1062679163 mscb->apfMsLwappLradPort = 40089
    *osapiBsnTimer: May 09 11:45:09.848: 00:1b:77:b4:34:e0 802.1x 'timeoutEvt' Timer expired for station 00:1b:77:b4:34:e0 and for message = M2
    *dot1xMsgTask: May 09 11:45:09.849: 00:1b:77:b4:34:e0 Retransmit failure for EAPOL-Key M1 to mobile 00:1b:77:b4:34:e0, retransmit count 3, mscb deauth count 3
    *dot1xMsgTask: May 09 11:45:09.849: 00:1b:77:b4:34:e0 Blacklisting (if enabled) mobile 00:1b:77:b4:34:e0
    *dot1xMsgTask: May 09 11:45:09.849: 00:1b:77:b4:34:e0 0.0.0.0 8021X_REQD (3) Change state to START (0) last state 8021X_REQD (3)
    *dot1xMsgTask: May 09 11:45:09.849: 00:1b:77:b4:34:e0 0.0.0.0 START (0) Reached FAILURE: from line 5274
    *dot1xMsgTask: May 09 11:45:09.849: 00:1b:77:b4:34:e0 Scheduling deletion of Mobile Station:  (callerId: 9) in 10 seconds
    *apfMsConnTask_4: May 09 11:45:15.689: 00:1b:77:b4:34:e0 Reassociation received from mobile on BSSID 18:9c:5d:71:34:50
    *apfMsConnTask_4: May 09 11:45:15.689: 00:1b:77:b4:34:e0 Global 200 Clients are allowed to AP radio
    *apfMsConnTask_4: May 09 11:45:15.689: 00:1b:77:b4:34:e0 Max Client Trap Threshold: 0  cur: 1
    *apfMsConnTask_4: May 09 11:45:15.689: 00:1b:77:b4:34:e0 Rf profile 600 Clients are allowed to AP wlan
    *apfMsConnTask_4: May 09 11:45:15.689: 00:1b:77:b4:34:e0 Applying Interface policy on Mobile, role Unassociated. Ms NAC State 2 Quarantine Vlan 0 Access Vlan 1
    *apfMsConnTask_4: May 09 11:45:15.689: 00:1b:77:b4:34:e0 Re-applying interface policy for client
    *apfMsConnTask_4: May 09 11:45:15.689: 00:1b:77:b4:34:e0 0.0.0.0 START (0) Changing IPv4 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2202)
    *apfMsConnTask_4: May 09 11:45:15.689: 00:1b:77:b4:34:e0 0.0.0.0 START (0) Changing IPv6 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2223)
    *apfMsConnTask_4: May 09 11:45:15.689: 00:1b:77:b4:34:e0 apfApplyWlanPolicy: Apply WLAN Policy over PMIPv6 Client Mobility Type
    *apfMsConnTask_4: May 09 11:45:15.689: 00:1b:77:b4:34:e0 In processSsidIE:4795 setting Central switched to TRUE
    *apfMsConnTask_4: May 09 11:45:15.689: 00:1b:77:b4:34:e0 In processSsidIE:4798 apVapId = 1 and Split Acl Id = 65535
    *apfMsConnTask_4: May 09 11:45:15.690: 00:1b:77:b4:34:e0 Applying site-specific Local Bridging override for station 00:1b:77:b4:34:e0 - vapId 1, site 'default-group', interface 'catodos'
    *apfMsConnTask_4: May 09 11:45:15.690: 00:1b:77:b4:34:e0 Applying Local Bridging Interface Policy for station 00:1b:77:b4:34:e0 - vlan 1, interface id 12, interface 'catodos'
    *apfMsConnTask_4: May 09 11:45:15.690: 00:1b:77:b4:34:e0 processSsidIE  statusCode is 0 and status is 0
    *apfMsConnTask_4: May 09 11:45:15.690: 00:1b:77:b4:34:e0 processSsidIE  ssid_done_flag is 0 finish_flag is 0
    *apfMsConnTask_4: May 09 11:45:15.690: 00:1b:77:b4:34:e0 STA - rates (8): 2 4 11 22 12 18 24 36 48 72 96 108 0 0 0 0
    *apfMsConnTask_4: May 09 11:45:15.690: 00:1b:77:b4:34:e0 suppRates  statusCode is 0 and gotSuppRatesElement is 1
    *apfMsConnTask_4: May 09 11:45:15.690: 00:1b:77:b4:34:e0 STA - rates (12): 2 4 11 22 12 18 24 36 48 72 96 108 0 0 0 0
    *apfMsConnTask_4: May 09 11:45:15.690: 00:1b:77:b4:34:e0 extSuppRates  statusCode is 0 and gotExtSuppRatesElement is 1
    *apfMsConnTask_4: May 09 11:45:15.690: 00:1b:77:b4:34:e0 Processing RSN IE type 48, length 20 for mobile 00:1b:77:b4:34:e0
    *apfMsConnTask_4: May 09 11:45:15.690: 00:1b:77:b4:34:e0 0.0.0.0 START (0) Initializing policy
    *apfMsConnTask_4: May 09 11:45:15.690: 00:1b:77:b4:34:e0 0.0.0.0 START (0) Change state to AUTHCHECK (2) last state START (0)
    *apfMsConnTask_4: May 09 11:45:15.690: 00:1b:77:b4:34:e0 0.0.0.0 AUTHCHECK (2) Change state to 8021X_REQD (3) last state AUTHCHECK (2)
    *apfMsConnTask_4: May 09 11:45:15.690: 00:1b:77:b4:34:e0 Central switch is TRUE
    *apfMsConnTask_4: May 09 11:45:15.690: 00:1b:77:b4:34:e0 Not Using WMM Compliance code qosCap 00
    *apfMsConnTask_4: May 09 11:45:15.690: 00:1b:77:b4:34:e0 0.0.0.0 8021X_REQD (3) Plumbed mobile LWAPP rule on AP 18:9c:5d:71:34:50 vapId 1 apVapId 1 flex-acl-name:
    *apfMsConnTask_4: May 09 11:45:15.690: 00:1b:77:b4:34:e0 apfPemAddUser2 (apf_policy.c:333) Changing state for mobile 00:1b:77:b4:34:e0 on AP 18:9c:5d:71:34:50 from Associated to Associated
    *apfMsConnTask_4: May 09 11:45:15.690: 00:1b:77:b4:34:e0 apfPemAddUser2:session timeout forstation 00:1b:77:b4:34:e0 - Session Tout 1800, apfMsTimeOut '1800' and sessionTimerRunning flag is  0
    *apfMsConnTask_4: May 09 11:45:15.690: 00:1b:77:b4:34:e0 Scheduling deletion of Mobile Station:  (callerId: 49) in 1800 seconds
    *apfMsConnTask_4: May 09 11:45:15.690: 00:1b:77:b4:34:e0 Func: apfPemAddUser2, Ms Timeout = 1800, Session Timeout = 1800
    *apfMsConnTask_4: May 09 11:45:15.690: 00:1b:77:b4:34:e0 Sending Assoc Response to station on BSSID 18:9c:5d:71:34:50 (status 0) ApVapId 1 Slot 0
    *apfMsConnTask_4: May 09 11:45:15.691: 00:1b:77:b4:34:e0 apfProcessAssocReq (apf_80211.c:8292) Changing state for mobile 00:1b:77:b4:34:e0 on AP 18:9c:5d:71:34:50 from Associated to Associated
    *spamApTask6: May 09 11:45:15.693: 00:1b:77:b4:34:e0 Sent 1x initiate message to multi thread task for mobile 00:1b:77:b4:34:e0
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.693: 00:1b:77:b4:34:e0 Creating a PKC PMKID Cache entry for station 00:1b:77:b4:34:e0 (RSN 2)
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.693: 00:1b:77:b4:34:e0 Resetting MSCB PMK Cache Entry 0 for station 00:1b:77:b4:34:e0
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.693: 00:1b:77:b4:34:e0 Removing BSSID 18:9c:5d:71:34:50 from PMKID cache of station 00:1b:77:b4:34:e0
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.693: 00:1b:77:b4:34:e0 Setting active key cache index 0 ---> 8
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.693: 00:1b:77:b4:34:e0 Setting active key cache index 8 ---> 0
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.693: 00:1b:77:b4:34:e0 Adding BSSID 18:9c:5d:71:34:50 to PMKID cache at index 0 for station 00:1b:77:b4:34:e0
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.693: New PMKID: (16)
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.693:      [0000] f6 3d 52 9f 2a de 52 90 1d a2 46 49 0f 14 f6 69
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.693: 00:1b:77:b4:34:e0 Initiating RSN PSK to mobile 00:1b:77:b4:34:e0
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.693: 00:1b:77:b4:34:e0 EAP-PARAM Debug - eap-params for Wlan-Id :1 is disabled - applying Global eap timers and retries
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.693: 00:1b:77:b4:34:e0 dot1x - moving mobile 00:1b:77:b4:34:e0 into Force Auth state
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.693: 00:1b:77:b4:34:e0 EAPOL Header:
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.694: 00000000: 02 03 00 5f                                       ..._
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.694: 00:1b:77:b4:34:e0 Found an cache entry for BSSID 18:9c:5d:71:34:50 in PMKID cache at index 0 of station 00:1b:77:b4:34:e0
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.694: 00:1b:77:b4:34:e0 Found an cache entry for BSSID 18:9c:5d:71:34:50 in PMKID cache at index 0 of station 00:1b:77:b4:34:e0
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.694: Including PMKID in M1  (16)
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.694:      [0000] f6 3d 52 9f 2a de 52 90 1d a2 46 49 0f 14 f6 69
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.694: 00:1b:77:b4:34:e0 Starting key exchange to mobile 00:1b:77:b4:34:e0, data packets will be dropped
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.694: 00:1b:77:b4:34:e0 Sending EAPOL-Key Message to mobile 00:1b:77:b4:34:e0
       state INITPMK (message 1), replay counter 00.00.00.00.00.00.00.00
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.694: 00:1b:77:b4:34:e0 Sending EAPOL-Key Message to mobile 00:1b:77:b4:34:e0
       state INITPMK (message 1), replay counter 00.00.00.00.00.00.00.00
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.694: 00:1b:77:b4:34:e0 Reusing allocated memory for  EAP Pkt for retransmission to mobile 00:1b:77:b4:34:e0
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.694: 00:1b:77:b4:34:e0 mscb->apfMsLwappLradNhMac = 78:da:6e:59:c9:8c mscb->apfMsLradSlotId = 0 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.694: 00:1b:77:b4:34:e0  mscb->apfMsBssid = 18:9c:5d:71:34:50 mscb->apfMsAddress = 00:1b:77:b4:34:e0 mscb->apfMsApVapId = 1
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.694: 00:1b:77:b4:34:e0  dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 0 mscb->apfMsLwappMwarInet.ipv4.addr = -1062679171
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.694: 00:1b:77:b4:34:e0  mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = -1062679163 mscb->apfMsLwappLradPort = 40089
    *apfMsConnTask_4: May 09 11:45:15.875: 00:1b:77:b4:34:e0 Reassociation received from mobile on BSSID 18:9c:5d:71:34:50
    *apfMsConnTask_4: May 09 11:45:15.875: 00:1b:77:b4:34:e0 Global 200 Clients are allowed to AP radio
    *apfMsConnTask_4: May 09 11:45:15.875: 00:1b:77:b4:34:e0 Max Client Trap Threshold: 0  cur: 1
    *apfMsConnTask_4: May 09 11:45:15.875: 00:1b:77:b4:34:e0 Rf profile 600 Clients are allowed to AP wlan
    *apfMsConnTask_4: May 09 11:45:15.876: 00:1b:77:b4:34:e0 Applying Interface policy on Mobile, role Unassociated. Ms NAC State 2 Quarantine Vlan 0 Access Vlan 1
    *apfMsConnTask_4: May 09 11:45:15.876: 00:1b:77:b4:34:e0 Re-applying interface policy for client
    *apfMsConnTask_4: May 09 11:45:15.876: 00:1b:77:b4:34:e0 0.0.0.0 8021X_REQD (3) Changing IPv4 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2202)
    *apfMsConnTask_4: May 09 11:45:15.876: 00:1b:77:b4:34:e0 0.0.0.0 8021X_REQD (3) Changing IPv6 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2223)
    *apfMsConnTask_4: May 09 11:45:15.876: 00:1b:77:b4:34:e0 apfApplyWlanPolicy: Apply WLAN Policy over PMIPv6 Client Mobility Type
    *apfMsConnTask_4: May 09 11:45:15.876: 00:1b:77:b4:34:e0 In processSsidIE:4795 setting Central switched to TRUE
    *apfMsConnTask_4: May 09 11:45:15.876: 00:1b:77:b4:34:e0 In processSsidIE:4798 apVapId = 1 and Split Acl Id = 65535
    *apfMsConnTask_4: May 09 11:45:15.876: 00:1b:77:b4:34:e0 Applying site-specific Local Bridging override for station 00:1b:77:b4:34:e0 - vapId 1, site 'default-group', interface 'catodos'
    *apfMsConnTask_4: May 09 11:45:15.876: 00:1b:77:b4:34:e0 Applying Local Bridging Interface Policy for station 00:1b:77:b4:34:e0 - vlan 1, interface id 12, interface 'catodos'
    *apfMsConnTask_4: May 09 11:45:15.876: 00:1b:77:b4:34:e0 processSsidIE  statusCode is 0 and status is 0
    *apfMsConnTask_4: May 09 11:45:15.876: 00:1b:77:b4:34:e0 processSsidIE  ssid_done_flag is 0 finish_flag is 0
    *apfMsConnTask_4: May 09 11:45:15.876: 00:1b:77:b4:34:e0 STA - rates (8): 2 4 11 22 12 18 24 36 48 72 96 108 0 0 0 0
    *apfMsConnTask_4: May 09 11:45:15.876: 00:1b:77:b4:34:e0 suppRates  statusCode is 0 and gotSuppRatesElement is 1
    *apfMsConnTask_4: May 09 11:45:15.876: 00:1b:77:b4:34:e0 STA - rates (12): 2 4 11 22 12 18 24 36 48 72 96 108 0 0 0 0
    *apfMsConnTask_4: May 09 11:45:15.876: 00:1b:77:b4:34:e0 extSuppRates  statusCode is 0 and gotExtSuppRatesElement is 1
    *apfMsConnTask_4: May 09 11:45:15.876: 00:1b:77:b4:34:e0 Processing RSN IE type 48, length 20 for mobile 00:1b:77:b4:34:e0
    *apfMsConnTask_4: May 09 11:45:15.876: 00:1b:77:b4:34:e0 0.0.0.0 8021X_REQD (3) Initializing policy
    *apfMsConnTask_4: May 09 11:45:15.876: 00:1b:77:b4:34:e0 0.0.0.0 8021X_REQD (3) Change state to AUTHCHECK (2) last state 8021X_REQD (3)
    *apfMsConnTask_4: May 09 11:45:15.876: 00:1b:77:b4:34:e0 0.0.0.0 AUTHCHECK (2) Change state to 8021X_REQD (3) last state AUTHCHECK (2)
    *apfMsConnTask_4: May 09 11:45:15.876: 00:1b:77:b4:34:e0 Central switch is TRUE
    *apfMsConnTask_4: May 09 11:45:15.876: 00:1b:77:b4:34:e0 Not Using WMM Compliance code qosCap 00
    *apfMsConnTask_4: May 09 11:45:15.876: 00:1b:77:b4:34:e0 0.0.0.0 8021X_REQD (3) Plumbed mobile LWAPP rule on AP 18:9c:5d:71:34:50 vapId 1 apVapId 1 flex-acl-name:
    *apfMsConnTask_4: May 09 11:45:15.876: 00:1b:77:b4:34:e0 apfPemAddUser2 (apf_policy.c:333) Changing state for mobile 00:1b:77:b4:34:e0 on AP 18:9c:5d:71:34:50 from Associated to Associated
    *apfMsConnTask_4: May 09 11:45:15.877: 00:1b:77:b4:34:e0 apfPemAddUser2:session timeout forstation 00:1b:77:b4:34:e0 - Session Tout 1800, apfMsTimeOut '1800' and sessionTimerRunning flag is  0
    *apfMsConnTask_4: May 09 11:45:15.877: 00:1b:77:b4:34:e0 Scheduling deletion of Mobile Station:  (callerId: 49) in 1800 seconds
    *apfMsConnTask_4: May 09 11:45:15.877: 00:1b:77:b4:34:e0 Func: apfPemAddUser2, Ms Timeout = 1800, Session Timeout = 1800
    *apfMsConnTask_4: May 09 11:45:15.877: 00:1b:77:b4:34:e0 Sending Assoc Response to station on BSSID 18:9c:5d:71:34:50 (status 0) ApVapId 1 Slot 0
    *apfMsConnTask_4: May 09 11:45:15.877: 00:1b:77:b4:34:e0 apfProcessAssocReq (apf_80211.c:8292) Changing state for mobile 00:1b:77:b4:34:e0 on AP 18:9c:5d:71:34:50 from Associated to Associated
    *spamApTask6: May 09 11:45:15.878: 00:1b:77:b4:34:e0 Sent 1x initiate message to multi thread task for mobile 00:1b:77:b4:34:e0
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.879: 00:1b:77:b4:34:e0 Creating a PKC PMKID Cache entry for station 00:1b:77:b4:34:e0 (RSN 2)
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.879: 00:1b:77:b4:34:e0 Resetting MSCB PMK Cache Entry 0 for station 00:1b:77:b4:34:e0
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.879: 00:1b:77:b4:34:e0 Removing BSSID 18:9c:5d:71:34:50 from PMKID cache of station 00:1b:77:b4:34:e0
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.879: 00:1b:77:b4:34:e0 Setting active key cache index 0 ---> 8
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.879: 00:1b:77:b4:34:e0 Setting active key cache index 8 ---> 0
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.879: 00:1b:77:b4:34:e0 Adding BSSID 18:9c:5d:71:34:50 to PMKID cache at index 0 for station 00:1b:77:b4:34:e0
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.879: New PMKID: (16)
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.879:      [0000] f6 3d 52 9f 2a de 52 90 1d a2 46 49 0f 14 f6 69
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.879: 00:1b:77:b4:34:e0 Initiating RSN PSK to mobile 00:1b:77:b4:34:e0
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.879: 00:1b:77:b4:34:e0 EAP-PARAM Debug - eap-params for Wlan-Id :1 is disabled - applying Global eap timers and retries
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.879: 00:1b:77:b4:34:e0 dot1x - moving mobile 00:1b:77:b4:34:e0 into Force Auth state
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.879: 00:1b:77:b4:34:e0 EAPOL Header:
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.879: 00000000: 02 03 00 5f                                       ..._
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.879: 00:1b:77:b4:34:e0 Found an cache entry for BSSID 18:9c:5d:71:34:50 in PMKID cache at index 0 of station 00:1b:77:b4:34:e0
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.879: 00:1b:77:b4:34:e0 Found an cache entry for BSSID 18:9c:5d:71:34:50 in PMKID cache at index 0 of station 00:1b:77:b4:34:e0
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.879: Including PMKID in M1  (16)
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.879:      [0000] f6 3d 52 9f 2a de 52 90 1d a2 46 49 0f 14 f6 69
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.879: 00:1b:77:b4:34:e0 Starting key exchange to mobile 00:1b:77:b4:34:e0, data packets will be dropped
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.879: 00:1b:77:b4:34:e0 Sending EAPOL-Key Message to mobile 00:1b:77:b4:34:e0
       state INITPMK (message 1), replay counter 00.00.00.00.00.00.00.00
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.879: 00:1b:77:b4:34:e0 Sending EAPOL-Key Message to mobile 00:1b:77:b4:34:e0
       state INITPMK (message 1), replay counter 00.00.00.00.00.00.00.00
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.879: 00:1b:77:b4:34:e0 Reusing allocated memory for  EAP Pkt for retransmission to mobile 00:1b:77:b4:34:e0
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.879: 00:1b:77:b4:34:e0 mscb->apfMsLwappLradNhMac = 78:da:6e:59:c9:8c mscb->apfMsLradSlotId = 0 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.879: 00:1b:77:b4:34:e0  mscb->apfMsBssid = 18:9c:5d:71:34:50 mscb->apfMsAddress = 00:1b:77:b4:34:e0 mscb->apfMsApVapId = 1
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.879: 00:1b:77:b4:34:e0  dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 0 mscb->apfMsLwappMwarInet.ipv4.addr = -1062679171
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.879: 00:1b:77:b4:34:e0  mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = -1062679163 mscb->apfMsLwappLradPort = 40089
    *osapiBsnTimer: May 09 11:45:18.048: 00:1b:77:b4:34:e0 802.1x 'timeoutEvt' Timer expired for station 00:1b:77:b4:34:e0 and for message = M2
    *dot1xMsgTask: May 09 11:45:18.049: 00:1b:77:b4:34:e0 Retransmit 1 of EAPOL-Key M1 (length 121) for mobile 00:1b:77:b4:34:e0
    *dot1xMsgTask: May 09 11:45:18.049: 00:1b:77:b4:34:e0 mscb->apfMsLwappLradNhMac = 78:da:6e:59:c9:8c mscb->apfMsLradSlotId = 0 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
    *dot1xMsgTask: May 09 11:45:18.049: 00:1b:77:b4:34:e0  mscb->apfMsBssid = 18:9c:5d:71:34:50 mscb->apfMsAddress = 00:1b:77:b4:34:e0 mscb->apfMsApVapId = 1
    *dot1xMsgTask: May 09 11:45:18.049: 00:1b:77:b4:34:e0  dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 0 mscb->apfMsLwappMwarInet.ipv4.addr = -1062679171
    *dot1xMsgTask: May 09 11:45:18.049: 00:1b:77:b4:34:e0  mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = -1062679163 mscb->apfMsLwappLradPort = 40089
    *osapiBsnTimer: May 09 11:45:20.049: 00:1b:77:b4:34:e0 802.1x 'timeoutEvt' Timer expired for station 00:1b:77:b4:34:e0 and for message = M2
    *dot1xMsgTask: May 09 11:45:20.049: 00:1b:77:b4:34:e0 Retransmit 2 of EAPOL-Key M1 (length 121) for mobile 00:1b:77:b4:34:e0
    *dot1xMsgTask: May 09 11:45:20.049: 00:1b:77:b4:34:e0 mscb->apfMsLwappLradNhMac = 78:da:6e:59:c9:8c mscb->apfMsLradSlotId = 0 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
    *dot1xMsgTask: May 09 11:45:20.049: 00:1b:77:b4:34:e0  mscb->apfMsBssid = 18:9c:5d:71:34:50 mscb->apfMsAddress = 00:1b:77:b4:34:e0 mscb->apfMsApVapId = 1
    *dot1xMsgTask: May 09 11:45:20.049: 00:1b:77:b4:34:e0  dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 0 mscb->apfMsLwappMwarInet.ipv4.addr = -1062679171
    *dot1xMsgTask: May 09 11:45:20.049: 00:1b:77:b4:34:e0  mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = -1062679163 mscb->apfMsLwappLradPort = 40089
    *osapiBsnTimer: May 09 11:45:22.048: 00:1b:77:b4:34:e0 802.1x 'timeoutEvt' Timer expired for station 00:1b:77:b4:34:e0 and for message = M2
    *dot1xMsgTask: May 09 11:45:22.049: 00:1b:77:b4:34:e0 Retransmit failure for EAPOL-Key M1 to mobile 00:1b:77:b4:34:e0, retransmit count 3, mscb deauth count 0
    *dot1xMsgTask: May 09 11:45:22.049: 00:1b:77:b4:34:e0 Resetting MSCB PMK Cache Entry 0 for station 00:1b:77:b4:34:e0
    *dot1xMsgTask: May 09 11:45:22.049: 00:1b:77:b4:34:e0 Removing BSSID 18:9c:5d:71:34:50 from PMKID cache of station 00:1b:77:b4:34:e0
    *dot1xMsgTask: May 09 11:45:22.049: 00:1b:77:b4:34:e0 Setting active key cache index 0 ---> 8
    *dot1xMsgTask: May 09 11:45:22.049: 00:1b:77:b4:34:e0 Sent Deauthenticate to mobile on BSSID 18:9c:5d:71:34:50 slot 0(caller 1x_ptsm.c:598)
    *dot1xMsgTask: May 09 11:45:22.049: 00:1b:77:b4:34:e0 Setting active key cache index 8 ---> 8
    *dot1xMsgTask: May 09 11:45:22.049: 00:1b:77:b4:34:e0 Deleting the PMK cache when de-authenticating the client.
    *dot1xMsgTask: May 09 11:45:22.049: 00:1b:77:b4:34:e0 Global PMK Cache deletion failed.
    *dot1xMsgTask: May 09 11:45:22.049: 00:1b:77:b4:34:e0 Scheduling deletion of Mobile Station:  (callerId: 57) in 10 seconds
    *dot1xMsgTask: May 09 11:45:22.049: 00:1b:77:b4:34:e0 Freeing EAP Retransmit Bufer for mobile 00:1b:77:b4:34:e0
    *osapiBsnTimer: May 09 11:45:32.048: 00:1b:77:b4:34:e0 apfMsExpireCallback (apf_ms.c:625) Expiring Mobile!
    *apfReceiveTask: May 09 11:45:32.049: 00:1b:77:b4:34:e0 apfMsExpireMobileStation (apf_ms.c:6632) Changing state for mobile 00:1b:77:b4:34:e0 on AP 18:9c:5d:71:34:50 from Associated to Disassociated
    *apfReceiveTask: May 09 11:45:32.049: 00:1b:77:b4:34:e0 Scheduling deletion of Mobile Station:  (callerId: 45) in 10 seconds
    Thanks for any advice

    In some of the big name brands of wireless, there is "no such thing" as 802.11n on a 2.4 Ghz.  No such thing because Cisco won't allow you (any more) to do channel bonding of 2.4 Ghz.  It doesn't make any sense to bond an already restricted 2.4 Ghz non-overlapping channel (three) and squeeze this number down to two.  
    Can you check to ensure that the data rates for 802.11b are enabled?  Maybe someone disabled data rates from 1 Mbps to 11 Mbps.

  • WLC 2106 and 802.1q

    Does the 2106 support 802.1q trunks. If so what do you have to do to enable a trunk port?

    The 2106 does support 802.1q trunking only. You don't have to do anything on the wlc side, Just configure the trunk port on the switch to 802.1q. Also the management and ap manager should be configured as the native vlan on the switch.

  • How to find out how many 802.11b clients are connecting

    Hello
    We got around 70 Cisco AP1231 here in autonomous function.
    They're all equiped with 802.11b/g modules.
    I'd like to soon disable 802.11b here (school), but I should somehow find out how many people are still using 802.11b.
    Any ideas how I could automatically do this?
    I also have a WLSE working here.
    Thanks,
    Patrick

    Whether it is IOS software or vx works software you could view the number of clients by clicking on home tab:summary status page.It would listed in the top of the page.If you are using CLI use the command show dot11 associations statistics in the Prev EXec mode. Refer URL http://www.cisco.com/en/US/products/hw/routers/ps272/products_technical_reference_chapter09186a008022e0e3.html#wp2645138

  • Disabling 802.11 b clients on a 5508 WLC version 7.0.116.0

    Hi,
    We have a rquirment to disable WLAN access to B clients. I believe the best way to do this is to change data rates in -
    Wireless >802.11b/g/n > network > Data Rates
    diable 1,2,5.5 and 11.
    Mandatory 6
    Supported 9,12,18,24,36,48,54
    A suggestion made to me was to untick the box in -
    Wireless >802.11b/g/n > network > 802.11b/g Network Status
    But I believe doing this from my testing disables the 2.4  B/G radio globally all together. Is there any other method for diabling B clients while leaving G clients ont he 2.4 radio  intact?

    You could set 12Mb to Mandatory, I think that would prevent B clients from associating globally.
    But if it is only a specific WLAN that you never want to support B Clients, you could always set that WLAN Radio policy to 802.11G/A only.... (I think that is still an option).   It should allow G/N and A/N clients, but disallow B clients.      I read somewhere that band select wont work if the radio policy is not ALL, so maybe not viable for you if you use band select (or perhaps this has been fixed).
    Either way I think you have several options at your disposal, not just disabling all B rates..... (this this is the easiest approach if you want all B clients gone, and you have coverage to support non 1,2,5.5,11 rates.
    -Wesley Terry

  • How to enable 802.11n in WLC 2106???

    Hi,
    I had already posted for help with this issue but I could not find that topic in the forums.
    So what I need is to eable the 802.11n service in my WLC sice 802.11g is the one working.
    Regards!

    Hi Nico,
    (Cisco Controller) >show country
    Configured Country............................. MX  - Mexico
    Configured Country Codes
            MX  - Mexico.................................... 802.11a / 802.11b / 802.11g
    AP Model
    1- AIR-AP1141N-A-K9
    (I am trying to convert it to LWAPP but cannot add it to the WLC yet, I have annother opened discussion for this case)
    But also I want to enable 802.11a in the rest of APs which are 1131 that were converted from Stand Alone to LWAPP.

  • WLC 2106 problem

    Hello,
    I have problem with new one WLC 2106 controller. I make this basic configuration (after reset):
    (Cisco Controller) >show interface summary
    Interface Name                   Port Vlan Id  IP Address      Type    Ap Mgr Guest
    ap-manager                       1    10       10.10.10.21     Static  Yes    No
    management                       1    10       10.10.10.20     Static  No     No
    virtual                          N/A  N/A      1.1.1.1         Static  No     No
    At this point, everything works OK. Controller is accesible via HTTPS, AP (one 1130) is connected too. But next I need create new WLAN and another interface VLAN - named ak-lan
    config interface create ak-lan
    config interface port ak-lan 1
    HTTPS acces is still working, but when I configure IP adress:
    config interface address dynamic-interface ak-lan 10.10.11.10 255.255.255.0 10.10.11.1
    HTTPS acces stops. In fact, it seem like HTTPS starts on new interface - it's accesible via 10.10.11.10, but (after certificate warning) shows only empty page (Page is not accesible..)
    I dont have an idea why. I tray downgrade software (originaly comes with 7.0.98.0) to 6.0.196.0, whitch I use on another same controller, but the behavior is the same. Now I use software 6.0.199.4. Again the same behavior.
    "show interface summary" says:
    (Cisco Controller) >show interface summary
    Interface Name                   Port Vlan Id  IP Address      Type    Ap Mgr Guest
    ak-lan                           1    11       10.10.11.10     Dynamic No     No
    ap-manager                       1    10       10.10.10.21     Static  Yes    No
    management                       1    10       10.10.10.20     Static  No     No
    virtual                          N/A  N/A      1.1.1.1         Static  No     No
    (Cisco Controller) >
    All interfaces (excluding virtual) matched to ping. All ïnterfaces have netmask 255.255.255.0.
    There was another strange thing - "show sysinfo" says that I use sw 6.0.199.4 and emergency is 7.0.98.0, but "show boot" says:
    (Cisco Controller) >show boot
    Primary Boot Image............................... 6.0.199.4 (active)
    Backup Boot Image................................ 6.0.196.0
    (Cisco Controller) >
    (Cisco Controller) >show sysinfo
    Manufacturer's Name.............................. Cisco Systems Inc.
    Product Name..................................... Cisco Controller
    Product Version.................................. 6.0.199.4
    RTOS Version..................................... 6.0.199.4
    Bootloader Version............................... 4.0.191.0
    Emergency Image Version.......................... 7.0.98.0
    Build Type....................................... DATA + WPS
    System Name...................................... ak-wlc
    System Location..................................
    System Contact...................................
    System ObjectID.................................. 1.3.6.1.4.1.9.1.828
    IP Address....................................... 10.10.10.20
    System Up Time................................... 0 days 0 hrs 46 mins 35 secs
    System Timezone Location.........................
    Configured Country............................... DE  - Germany
    Operating Environment............................ Commercial (0 to 40 C)
    Internal Temp Alarm Limits....................... 0 to 65 C
    Internal Temperature............................. +55 C
    State of 802.11b Network......................... Enabled
    State of 802.11a Network......................... Enabled
    Number of WLANs.................................. 0
    3rd Party Access Point Support................... Disabled
    Number of Active Clients......................... 0
    Burned-in MAC Address............................ E0:5F:B9:63:7B:00

    Switch is C2960, port Gi0/2:
    Gi0/2     T wlc              connected    trunk      a-full  a-100 10/100/1000BaseTX
    interface GigabitEthernet0/2
    description T wlc
    switchport trunk allowed vlan 10,11,100
    switchport mode trunk
    end
    VLANs are set properly. Router is ASA 5510, and routing is fine. Morever, interfaces on WLC is accesible via ping (I dot't try telnet or ssh).

  • Photosmart C7250 wireless 802.11b fails

    My new C7250 works well with USB and wired ethernet, but fails miserably (prints slowly, if at all) on my wireless 802.11b network.  All other devices work well on my wireless network.  I've spent many hours with HP and exhausted their first line support.  They supposedly have opened a case but I have heard nothing in a week.  Meanwhile, I took a network trace using WireShark and it shows a large number of retransmissions.  (I'm expert with application/network performance profiling.)  All you have to do is browse to http://192.168.1.xxx/ to test transmission -- don't even need to install drivers or printers to see the errors.  This problem appears to be with wireless support on the C7250.
    Has anyone experienced problems or success with 802.11b on this device?  How about 802.11g?  I would be willing to upgrade my wireless if I knew that it would resolve the problem.
    What does it take to escalate a probem with HP for resolution?

    All 2004 and newer wireless HP Inkjet printers are compatible with 802.11g and 802.11b networks (otherwise we couldn't get 802.11g Wi-Fi certification).  Besides testing for interoperability, we test for a minimum wireless throughput at the TCP layer.
    I'd like to see the internal connectivity report that you can generate by pressing the <setup> and <#> buttons simultaneously.  Scan the report to a memory card, copy it to your PC and post the image here.
    It will tell me information about your wireless network and other networks in the area.
    I have a couple of other questions:
    Does the slow printing go away after a power cycling the printer and then does it return later?
    Does the slow printing go away after a power cycling the wireless-router and then does it return later?
    Are you seeing retransmissions of TCP, 802.3 (ethernet) frames or 802.11 frames?  I wasn't sure at what layer you are sniffing the data at?
    What make and model 802.11b wireless-router are you using?
    Do you have encryption enabled?  Does disabling encryption change the speed of printing?
    How many wireless PC's (Macs?) to you have on your network?  Do they all exhibit slow printing?
    Have you changed the default fragmentation settings of your wireless-router?
    At home, I routinely get 1.5 Mbytes/sec transfer rates between my 802.11g wireless-routers and my HP printers and about 700 Kbytes/sec in 802.11b mode.
    One other thing you can try is to go to the printers internal web page, browse over to the Networking, Wireless, Advanced page and enable the configuration "In an infrastructure network use 802.11b behavior".
    Regards / Jim B
    Regards / Jim B / Wireless Enthusiasts
    ( While I'm an embedded wireless systems engineer at work, on this forum I do not represent my former employer, Hewlett-Packard, or my current employer, Microsoft )
    + Click the White Kudos star on the left as a way to say "thank you" for helpful posts.

  • AP 1140 and WLC 2106

    Does someone know if WLC 2106 support AP 1140 ? I read that AP 1140 is CAPWAP only and I don't know if WLC 2106 supports CAPWAP.
    Thanks

    Yes it does, you may have to upgrade your controller software to get 802.11n and CAPWAP, use the latest code 6.0.182.
    CAPWAP was supported from code 5.2.157
    The max throughput on the 2106 though is only 100mbps so yo wont see the highest speeds

  • Help Enabling 802.11b Support

    Can anyone help? All I want to do is enable 802.11b support on my Cisco 877W. My 802.11g clients can see and attach to it no problems. My 802.11b clients cannot see it at all. I have tried all sorts but nothing has helped. My config looks like this:
    interface Dot11Radio0
    no ip address
    encryption key 1 size 128bit 7 BC48CE99C4E9B683819990D3C1A5 transmit-key
    encryption mode wep mandatory
    ssid *****
    authentication open
    speed basic-1.0 basic-2.0 basic-5.5 6.0 9.0 basic-11.0 12.0 18.0 24.0 36.0
    48.0 54.0
    station-role root
    no dot11 extension aironet
    bridge-group 1
    bridge-group 1 spanning-disabled
    What do I need to add to make it visible and available to 802.11b clients?
    Many Thanks,
    Matt

    I'd start by defaulting the AP back to factory default, no WEP, no authentication.
    Check to see if the 802.11b clients can connect.
    If all the 802.11b clients are running the same software, check to see that they are up-to-date drivers & client software. If you're using the MS client software (Zero Wireless Config) try a client using the vendor's client software instead.
    If the clients are not eve associating, look at the basic parameters: things like preamble length (legacy default is "long" which is a one meg data rate)
    If you can get the 802.11b client to connect whith all open parameters, then add WEP. Be advised that some clients need the WEP entered as HEX, not ASCII.
    For example ASCII "ABCD" would be "41 42 43 44" in hex ... make sure you're using the same system. IF youre using something like "12345abcde" that can be a valid (but incorrect) hex string when ou really intend for it to be ASCII.
    Also note that leading or training spaces (ASCII 20) are valid characters. Make sure you do not have leading or training spaces in your WEP (unless you really want them there, in whch case, make sure they're there)
    Make sure the Ethernet format is correct: use the Web GUI to set up. Check the parameters on the "Interfaces" page and do not (at least initially) use the "Best throughput" or "Best Range" settings, leave it at "Default Settings"
    If your 802.11b clients are PDAs, bar-code scanners, or other hand-held devices, check that they are at default settings for the standard 802.11b protocols; some use proprietary protocols for better performance or security.
    That's about it for me ... let us know if any of that changes (works / doesn't work, but acting differently / doesn't work, looks the same).
    Good Luck
    Scott

  • WLC 2106 with AP1120

    Hi,
    I have a Cisco Aironet AIR-AP1120B-A-K9 802.11b Wireless Access Point. Can I integrate this AP with AIR-WLC2106-K9.
    Thankx and regards
    Satish

    Hi Satish,
    Just to add a note to the good info from Jerome (+5 points for this Jerome :)
    Sadly, the 1120 with "B" Radio is not supported :(
    Support for the 1121 was added in WLC version 4.0.155.0 Have a look at these related docs;
    Software release 4.0.155.0 New Features
    LWAPP for Cisco Aironet 1100 Series Access Points (802.11g radio only) Allows the Cisco Aironet 1100 Series Access Point to be upgraded from autonomous access point mode to lightweight mode using the autonomous to lightweight mode upgrade tool.
    Note You must install software release 4.0.155.0 on the controller before connecting 1100 series access points to the controller.
    http://www.cisco.com/en/US/products/ps6366/prod_release_note09186a00806e8989.html#wp147320
    LWAPP Upgrade Tool Troubleshoot Tips
    http://www.cisco.com/en/US/tech/tk722/tk809/technologies_tech_note09186a008072d9a1.shtml
    Access points must run Cisco IOS Release 12.3(7)JA or later before you use the upgrade tool.
    System Requirements
    You can use the Autonomous to Lightweight Mode upgrade tool to install Cisco IOS Release 12.3(11)JX on these access points:
    **All 1100 series access points containing MP21G (802.11g) radios
    All 1130, 1230, and 1240 series access points
    All modular 1200 series access points running Cisco IOS software and containing these supported radios:
    802.11g: MP21G, MP31G
    802.11a: AIR-RM21A-x-K9, AIR-RM22A-x-K9
    All 1300 series access points in access point mode
    http://www.cisco.com/en/US/docs/wireless/access_point/ios/release/notes/b311jx1.html
    Cisco has released a free tool called the "Autonomous to Lightweight Mode Upgrade Tool" that allows selected Cisco Aironet autonomous access point models to be configured for lightweight mode operation.
    The Autonomous to Lightweight Mode Upgrade Tool supports the following models:
    Cisco Aironet 1240AG Series access points
    Cisco Aironet 1230AG Series access points
    Cisco Aironet 1200 Series access points that contain 802.11g (AIR-MP21G-x-K9) and/or second-generation 802.11a radios (AIR-RM21A-x-K9 or AIR-RM22A-x-K9)
    Cisco Aironet 1130AG Series access points
    **Cisco Aironet 1100 Series Access Points that contain 802.11g radios (AIR-AP1121G-x-K9)
    Cisco Aironet 1300 Series Access Points/Bridges (AIR-BR1310G-x-K9 or AIR-BR1310G-x-K9-R). A Cisco Aironet 1300 Series operating in Lightweight Access Point Protocol (LWAPP) mode only operates as an access point. This series does not support LWAPP bridging mode.
    The Autonomous to Lightweight Mode Upgrade Tool supports a process to migrate an autonomous access point from autonomous mode to lightweight mode. Unlike a VxWorks to Cisco IOS Software upgrade, this process is a Cisco IOS Software upgrade to the existing Cisco IOS Software image-not an operating system "swapout". In converted access points operating in lightweight mode, Cisco IOS Software continues to run on the access point, while LWAPP is used to communicate with a wireless LAN controller. Since LWAPP supports automatic access point configuration, there is no need to retain or convert the original autonomous Cisco IOS Software access point configuration.
    http://www.cisco.com/en/US/netsol/ns340/ns394/ns348/ns337/networking_solutions_white_paper0900aecd804f1a23.shtml
    Cisco Aironet Access Point Support for Lightweight Access Point Protocol
    http://www.cisco.com/en/US/products/ps6521/prod_bulletin0900aecd80321a2c.html
    Upgrading Autonomous Cisco Aironet Access Points to Lightweight Mode
    http://www.cisco.com/en/US/products/hw/wireless/ps430/prod_technical_reference09186a00804fc3dc.html#wp157147
    Hope this helps!
    Rob

  • WLC 2106 question

    Hello,
    What is the recomended way to connect  5 APs 1242 to a wlc 2106?
    Connect directly the 5 APs to the wlc and use one port for the management interface and connection to the switch or to connect the APs to a switch and use one connection for the wlc?
    Thanks in advance.

    Depends on the AP.
    One FastEthernet connection to the switch doens't "really" create a bottleneck.  Your AP might.  If you, say, you have 1130 or older then I'd say no significant bottleneck because the APs are also FastEthernet.
    If you use the newer ones, like the 1250 and newer, which has GigEthernet and/or higher throughput (if you enable 802.11n) the yes.  The switch AND the WLC 2100 are both the bottleneck.

Maybe you are looking for

  • Warning messages?

    How do I turn off the very annoying battery warning message? how do I disable battery warning message? Both these are very annoying and ever remind me of windows which I hate

  • Alternative to Hashtable? Got lots of data and "OutOfMemoryError"

    Hello, I am working on an application (CLDC1.1 and MIDP2.0, using NetBeans) and have to use a large look-up table with about 50 000 entries. During runtime the application is set to look up entries xxx times from the table, as fast as possible of cou

  • Import server: Undefined elements exception

    Hi, I do have a problem with the import server. I get ,'save-update map' structural exceptions in the import server. It complains about undefined elements, and if saved the update it works for one single XML file but other still fail with similar (ot

  • 8 core MACPRO

    hallo, i was just wondering how the 8 core mac was holding up...i may have the chance to sell my Macpro 2,6 and was considering getting a new 8 core macpro...i am an editor and motion graphic designer, using Avid, FCS 2, Adobe Creative suite, After E

  • Anyone have a syggestion on how to get my Ipod touch working again besides putting it into restore mode

    Anyone have any ideas on how to get an Ipod touch to charge or sync without putting it into restore mode, I've prettymuch tried everything thats been put online so far