Wlc 2106 problem ( cant connect to 2 lwapp ( 1242 & 1131 ) need advice

Dear All,
could you give me some advice to configure wlc with 2 lwapp,
i did try to used 1 lwapp ( 1242 ag ) and it's work, but when i try to connect with 2 lwapp ( 1242 & 1131 ), i can't associated with lwapp 1131 ag, i did used same configuration for both,
need youd advice and reference guide for this issue.
thanks and regards

Hi Heru,
If both are lwapp aps then they should be able to join 2106 controller. Can you confirm if 1130 is also connected to same subnet where 1242 is connected? Is management subnet/vlan different from the vlan you are connecting your LWAPP APs.
Hope this link should help
http://www.cisco.com/en/US/docs/wireless/controller/4.2/configuration/guide/c42lwap.html#wp1104685
HTH
Ankur
*Pls rate all helpfull post

Similar Messages

Hey there. This is wierd lolol. I just got a I phone 4. i cant connect my blue tooth. I need a PIN #??? what is that?

Hey there. This is wierd lolol. I just got a I phone 4. i cant connect my blue tooth. I need a PIN #??? what is that?

Try using 0000 if the instructions for your Bluetooth don't provide a passkey (PIN). Also, see if this helps:
iOS: Third-party Bluetooth headsets, headphones, and keyboards

WLC 2106 problem

Hello,
I have problem with new one WLC 2106 controller. I make this basic configuration (after reset):
(Cisco Controller) >show interface summary
Interface Name                   Port Vlan Id IP Address      Type    Ap Mgr Guest
ap-manager                       1    10       10.10.10.21     Static Yes    No
management                       1    10       10.10.10.20     Static No     No
virtual                          N/A N/A      1.1.1.1         Static No     No
At this point, everything works OK. Controller is accesible via HTTPS, AP (one 1130) is connected too. But next I need create new WLAN and another interface VLAN - named ak-lan
config interface create ak-lan
config interface port ak-lan 1
HTTPS acces is still working, but when I configure IP adress:
config interface address dynamic-interface ak-lan 10.10.11.10 255.255.255.0 10.10.11.1
HTTPS acces stops. In fact, it seem like HTTPS starts on new interface - it's accesible via 10.10.11.10, but (after certificate warning) shows only empty page (Page is not accesible..)
I dont have an idea why. I tray downgrade software (originaly comes with 7.0.98.0) to 6.0.196.0, whitch I use on another same controller, but the behavior is the same. Now I use software 6.0.199.4. Again the same behavior.
"show interface summary" says:
(Cisco Controller) >show interface summary
Interface Name                   Port Vlan Id IP Address      Type    Ap Mgr Guest
ak-lan                           1    11       10.10.11.10     Dynamic No     No
ap-manager                       1    10       10.10.10.21     Static Yes    No
management                       1    10       10.10.10.20     Static No     No
virtual                          N/A N/A      1.1.1.1         Static No     No
(Cisco Controller) >
All interfaces (excluding virtual) matched to ping. All ïnterfaces have netmask 255.255.255.0.
There was another strange thing - "show sysinfo" says that I use sw 6.0.199.4 and emergency is 7.0.98.0, but "show boot" says:
(Cisco Controller) >show boot
Primary Boot Image............................... 6.0.199.4 (active)
Backup Boot Image................................ 6.0.196.0
(Cisco Controller) >
(Cisco Controller) >show sysinfo
Manufacturer's Name.............................. Cisco Systems Inc.
Product Name..................................... Cisco Controller
Product Version.................................. 6.0.199.4
RTOS Version..................................... 6.0.199.4
Bootloader Version............................... 4.0.191.0
Emergency Image Version.......................... 7.0.98.0
Build Type....................................... DATA + WPS
System Name...................................... ak-wlc
System Location..................................
System Contact...................................
System ObjectID.................................. 1.3.6.1.4.1.9.1.828
IP Address....................................... 10.10.10.20
System Up Time................................... 0 days 0 hrs 46 mins 35 secs
System Timezone Location.........................
Configured Country............................... DE - Germany
Operating Environment............................ Commercial (0 to 40 C)
Internal Temp Alarm Limits....................... 0 to 65 C
Internal Temperature............................. +55 C
State of 802.11b Network......................... Enabled
State of 802.11a Network......................... Enabled
Number of WLANs.................................. 0
3rd Party Access Point Support................... Disabled
Number of Active Clients......................... 0
Burned-in MAC Address............................ E0:5F:B9:63:7B:00

Switch is C2960, port Gi0/2:
Gi0/2     T wlc              connected    trunk      a-full a-100 10/100/1000BaseTX
interface GigabitEthernet0/2
description T wlc
switchport trunk allowed vlan 10,11,100
switchport mode trunk
end
VLANs are set properly. Router is ASA 5510, and routing is fine. Morever, interfaces on WLC is accesible via ping (I dot't try telnet or ssh).

Cant connect jsp with mysqlserver..help needed from person in jsp on linux

hii,
I have installed mysql on linux 7.x.This was installed during installation of linux.From the shell prompt i can go inside mysql and can successfully execute all query statements.
Now have downloaded mm.mysqljdbc driver(i.2c) and installed it,set the classpath in .bash_profile,sh file
Everything ,including Tomcat Apache server is running fine
But i am unable to connect a jsp page to mysql database.
A error message "server configuration denies access to datasource " is coming .
My code is like this
<%
String username-"root"
String password="sdctest"
%>
<% try
class.forname("org.gjt.mm.mysql.Driver");
java.sql.Connectioncon= java.sql.DriverManager.getConnection("jdbc:mysql://localhost/products"username,password);
then opening recordset ....
Error is coming in the second line while establishing connection.
Here i would like to mention that username and password is the username and password of the root user in LInux.
Now i mm confused what username and password will have to be used in JSP.Because i did nt have to specify any username or password while entering mysql.
If my problem is clear,somebody please help...all jobs stuck.

Try doing it without the username and password, otherwise create a new user in MySQL.

My i pod cant connect to my computer and i need to restore it

cant restore my i pod touch or sync it to my computer.

Why not?
What happens when you try?
Have you tried a reset?

Kids' playroom. Connecting WII and Xbox... need advice on receiver

We just built the playroom and I wired for 5.1 and even ran the HDMI cable behind the wall to connect a receiver to the TV. This is for the kids room, may upgrade sometime, but they are 8 and 10, so sound purity and quality is not a big issue. Simplicity, simple operation and ability to have a single HDMI connection from receiver to TV is most important. Have simple Insignia speakers with powered subwoofer, now want to pick least expensive receiver for this room. Would also consider returning speakers if there is a home theater system that accepts both HDMI and analog input and does the job. Thanks!

Yes, I had considered running an etherent cable to the bedroom, but my wife doesn't like the idea of seeing the cable snaking through hallways.
In the bedroom, I have connected the imac, mac mini and the AEBS with etherent cable. It's just my connection to the internet that does not have the benefit of ethernet, although the speed I get from my cable internet is much slower than the wifi connection.
I would eventually like to move the cable modem upstairs and use the AEBS as the primary base station and the AX downstairs to extend my wireless network. However, there is an issue in that the cable modem has to be the only device on the cable connection and I am currently using the cable connection to carry my DISH Network signal and basic cable signal to the bedroom.
I guess my question really boils down to this...Would an AE in place of the AX give a stronger signal to the 2nd AE in the bedroom. I will turn off the AE tonight and see what kind of a signal I get from the AX downstairs. I haven't tried it, but I suppose I could also move the Airport Extreme (5th Gen) downstairs and hook it directly to the cable modem and not even use the AX because the signal from the new AE should be as good or better than last year's AX - but then I would lose the gigabit ethernet between those devices - which is why I haven't done that yet.
I could also drop the $$$ on a Time Capsule for the bedroom and use it for all my backups (but that's kinda what I'm hoping to do with the mac mini) and move the AE downstairs to the cable modem.
Decisions, decisions.

I have problem with my wifi in 4 S, i cant connect to any wifi itried resetting network setting and reset all setting but the result was the same, its only keeps searching for wifi and cant find any, itried to use OTHER but also didnt work.please help me

i have problem with my wifi in 4 S, i cant connect to any wifi itried resetting network setting and reset all setting but the result was the same, its only keeps searching for wifi and cant find any, itried to use OTHER but also didnt work.please help me???

If Join was on then your home wi-fi must be set to Non-Broadcast. If you did not set this up (maybe your provider did) then you will need to find the Network Name they used, and any password they used. The SSID is Security Set ID and to see more try http://en.wikipedia.org/wiki/SSID . Basically it is the name used to identify your router/network. A lot of times the installer will leave it set as LinkSys, or Broadcom or whatever the manufacturer set it as for default. Your best bet is to get whoever installed it to walk you through how they set it up, giving you id's and passwords so you can get in. HOWEVER, if you are not comfortable with this (if you set security wrong, etc.) you would be well ahead of the game to hire a local computer tech (networking) to get this working for you. You can also contact the vendor of your router and get help (if it is still in warranty), or at least get copies of the manuals as pdf files. Sorry I can't give you more help, I hope this gives you an idea where to go from here to find more.

I cant connect with my imessage and facetime in my iphone; i already upload de i os 7.02 but the message still have it; it said that they have problem with the network; i reset the network and doesnt work

I cant connect with my imessage and facetime in my iphone; i already upload de i os 7.02 but the message still have it; it said that they have problem with the network; i reset the network and doesnt work

Hello, Toro Silva.
Thank you for visiting Apple Support Communities.
The steps in the section labeled Unable to activate FaceTime or iMessage with phone number and Apple ID after waiting 24 hours (iPhone only) of the article below, should help resolve the issue. Make sure to create a current backup prior to processing these steps.
iOS: Troubleshooting FaceTime and iMessage activation
http://support.apple.com/kb/ts4268
Cheers,
Jason H

I had problem with my WiFi i cant connect with

hi
i had problem with my wifi that i cant connect with it

Look at iOS Troubleshooting Wi-Fi networks and connections http://support.apple.com/kb/TS1398
iPad: Issues connecting to Wi-Fi networks http://support.apple.com/kb/ts3304
Additional things to try.
Try this first. Turn Off your iPad. Then turn Off (disconnect power cord) the wireless router & then back On. Now boot your iPad. Hopefully it will see the WiFi.
Change the channel on your wireless router. Instructions at http://macintoshhowto.com/advanced/how-to-get-a-good-range-on-your-wireless-netw ork.html
How to Quickly Fix iPad 3 Wi-Fi Reception Problems
http://osxdaily.com/2012/03/21/fix-new-ipad-3-wi-fi-reception-problems/
If none of the above suggestions work, look at this link.
iPad Wi-Fi Problems: Comprehensive List of Fixes
http://appletoolbox.com/2010/04/ipad-wi-fi-problems-comprehensive-list-of-fixes/
Fix iPad Wifi Connection and Signal Issues http://www.youtube.com/watch?v=uwWtIG5jUxE
 Cheers, Tom

I have a problem with my iphone 4S. I cant connect to wifi a week ago. Can somebody help me please?

I have a problem with my iphone 4S. I cant connect to wifi a week ago. Can somebody help me please?
I have tried everything but my iphone continue without connected.
Thanks.

Hello.
My iphone doesn't recognize any signal wifi.
I have rebooted the red options as indicated on apple portal.
Also, I have turned off my iphone and when I turn it on don't enable the wifi option, and then I have to turn it off and turn it on again.
I have restored to the factory settings but the problem continues.
I don't know anything else to do.
Regards,

I cant connect my i phone 4 to my sony vaio laptop via bluetooth i am having problem can any one help me how can i connect my i phone 4 to my laptop using bluetooth i tried to paired but it just doesnt work help me pls!!

i cant connect my i phone 4 to my sony vaio laptop via bluetooth i am having problem can any one help me how can i connect my i phone 4 to my laptop using bluetooth i tried to paired but it just doesnt work help me pls!!

Unless you're trying to tether your phone to your computer or create a personal hotspot, it won't pair with your computer by bluetooth. File transfer by bluetooth is not supported. So, you can quit trying unless you're trying to tether.

Hi .i cant connect my camera roll to my hp laptop i have a 5s and i think ever since i upgraded to ios 7,1,1 this problem apeared

why can't i connect my camera roll any more? i have a 5s and recently i cant connect my camera roll to my lap top

Hello!
When you plug in your iPhone something shouldve poped up on your iPhone screen, saying Trust this computer? you may have accidentally pressed "Dont trust" if so it locks all photos on your phone so you cant see them from the computer. I would try another USB port and that same thing may pop up and make sure to press "Trust"
Also, you can try to go into my documents and on the left side you'll see "This PC" press that and you'll see an iphone on the screen, right click on it and it should have an option to "import pictures and videos" this may also work.
If this doesnt work please let us know!!
Best of luck!

WLC 2106 and Linksys Bridge WET610N works with 7.0.116.0 release?

Hi all,
i'm having troubles with WLC 2106 controller and several wireless bridges, so i'd like to know if i can fix it in some way.
My environment is as follows:
1 WLC 2106 with 2 Aironet 1240G
I have a production appliance that needs an ethernet port to work, so i bought a Linksys Bridge WET610N to make it works via wireless.
The Linksys bridge connects to the 1240G as a client and works well, but the appliance connected to the ethernet port of the bridge is unreachable.
Searching for the problem, i found that the wlc act as a proxy arp for the wireless clients and being the ethernet appliance a "passive" client, the controller isn't aware of it.
My WLC is running the 7.0.98.0 firmware. In the release notes for the 7.0.116.0, in the "Non-Cisco WGB Support" seems to state that now also non cisco bridges can work using the passive client feature. I've already enabled it on my controller but this didn't solve my problem.
Can anyone tell me if the upgrade to the 7.0.116.0 can fix it?
Thanks in advance
Riccardo Coppola

I'm not sure what (cheap) devices can do the wgb feature that is inter-brand compatible.
The thing is that the WLC enforces the rule "1 wireless client = 1 client". Meaning you can't bridge multiple clients behind a wireless clients, that just screws up roaming mechanisms etc ...
Cisco WGBs have the IAPP protocol to tell the WLC "listen, I'm a WGB wireless client and those are the wired clients connected to me, allow them on the network".
What does "universal WGB" feature does is that the WGB forwards the traffic of the client (only 1 client supported in this case !) to the infrastructure AP but the WGB never sends anything with its own mac address. It uses the client mac address as source.
This means that the WLC has no way of knowing that there is more than 1 device. It just thinks that your wired client is a wireless client.
So it's more than mac cloning since the WgB has to be the one authenticating to the infrastructure (Wpa/wpa2 whatsoever) by spoofing the client mac. The WGB is still in charge of roaming decisions and so on and so on...
I hope it clarifies the situation ?

Wlc 2106 mDns bonjour AirPlay AirTunes apple??? help

Hi guys,
Long time reader, first time poster.. I'm after some advice.
I'm failing dismally trying to configure a 2106 Wlc to allow apple device (iPhone, iPads) to stream AirPlay to an apple tv 2.
Now, I have this working perfectly with a 5508 WLC.
I understand that the apple devices all need to be on the same subnet (they are), that multicast needs to be enabled, and I've tried a variety of multicast addresses as mentioned in many posts.. Also the wired infrastructure is not the problem (as connecting net gear access points into the same wired infrastructure works fine).
I've also read posts where some people say the 2100series doesn't support AirPlay/bonjour/mDns and others saying they have had it work.
But I can't find a definitive answer.
Can anyone confirm or deny which WLC support AirPlay, as if I need to switch I want to make sure they do.
The 5508 works fine.
Anybody able to shed some wisdom?
Thanks Wayne.
Sent from Cisco Technical Support iPad App

I have a 2106 in the lab and it works fine. Here are a few screen shots and a link that may help..
http://www.cisco.com/en/US/docs/ios/12_2/ip/configuration/guide/1cfmulti.html

WLC-2106 and multiple interfaces on the same network

Hi there,
I recently created a TAC request to the Cisco support regarding our WLC-2106, but they could not help me. Basically I just learned that you can create new interfaces for the wireless LAN controller and then dedicate them to a given wireless network (SSID). This way I could more effectively utilize network bandwidth also. Problem is that all of the interfaces have to be in a different network segment in order to work, which is not what I want. I specifically want to have several interfaces on the same network segment.
Has anyone tried to accomplish the same?

Basically what I've misunderstood is that all the traffic generated by our wireless clients have been going through the single 100Mbit/s ethernet port on the wireless LAN controller (management interface), and to mitigate this I thought I could create new interfaces (ports) and dedicate those to given WLAN networks.. I see now that this is not supported. Not inside the same network at least.
So, by reading further and consulting my best friend Google I learned about a setting called "AP Mode". Changing that from Local (the default) to H-REAP the APs should not route their traffic anymore through the management interface on the wireless controller, but instead route all the client traffic directly to the local LAN. This way you effectively remove the 100Mbit/s bottle-neck when all the APs were using the management interface both for configuration and client data traffic.
It seems you also have to enable H-REAP Local switching from a given WLAN network in addition to changing the AP Mode of your access points to H-REAP. I'm still in the testing phase here so should anyone have any insight to this, I'd be greatful to hear more.

Wlc 2106 problem ( cant connect to 2 lwapp ( 1242 & 1131 ) need advice

Similar Messages

Maybe you are looking for