WLC 2112 is not accessable

Hello Experts,
I have a problem with my Cisco WLC 2112.
Problems:
1. I can not reach this WLC via GUI or CLI.
2. Can not access via Console.
3. Status LED is Dark Orange or Red.
Can anybody help.
Regards

Hi,
Status LED is Amber(ORANGE/RED)— Means Problem encountered during boot.
http://www.cisco.com/en/US/docs/wireless/controller/2100/quick/guide/ctrl206q.html#wp39363
Did u tried with these settings:
9600 baud
8 data bits
No flow control
1 stop bit
No parity
If the console is not responsive, then its a hardware failure and you should contact the TAC or You should RMA'd it.
Be aware: WLC 2100 Series are EOL/EOS.
http://www.cisco.com/en/US/prod/collateral/wireless/ps6302/ps8322/ps7206/ps7221/end_of_life_notice_c51-691053.html
Regards
Dont forget to rate helpful posts

Similar Messages

  • Not access WLC cisco 2106 by GUI interface

    Hi Expert ,
                    i am trying to configure it but i can not access GUI interface.it is true this is my frist time.please help me to access this GUI interface.

    I assume you have read through the Quick start guide for the 2106 controller?
    http://www.cisco.com/en/US/docs/wireless/controller/2100/quick/guide/ctrl206q.html
    Also the configuration guide covers connecting via cli and gui:
    http://www.cisco.com/en/US/docs/wireless/controller/5.2/configuration/guide/c52intf.html

  • WLC 2112 with LAP 1042N

    Hi Guys.
    we are trying to configure WLC 2112 with LAP 1042 but getting following erros on LAP1042.
    It show the Ap is not supported in controller version 6.0.199.4
    *Jan  5 16:52:13.397: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 192.168.2.101 peer_port: 5246
    *Jan  5 16:52:13.398: %CAPWAP-5-SENDJOIN: sending Join Request to 192.168.2.101
    *Jan  5 16:52:13.399: %CAPWAP-5-CHANGED: CAPWAP changed state to JOIN
    *Jan  5 16:52:13.410: %CAPWAP-3-ERRORLOG: This AP is not supported in controller version 6.0.199.4
    *Jan  5 16:52:13.495: %CAPWAP-5-CHANGED: CAPWAP changed state to CFG
    *Jan  5 16:52:13.496: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 192.168.2.101:5246
    *Jan  5 16:52:13.497: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
    *Jan  5 16:52:13.498: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
    *Jan  5 16:52:19.552: %CAPWAP-3-ERRORLOG: Dropping dtls packet since session is not established.
    *Jan  5 16:52:29.551: %CAPWAP-3-ERRORLOG: Go join a capwap controller
    WLC 2112 software version 6.0.199.4
    LAP 1042 image version 7.0.94.21
    If any one can help me out then it wolud be great.
    Thanks in advance for all.

    You should upgrade your controller to 7.0.116.0 or 7.0.220.0
    Sent from Cisco Technical Support iPhone App

  • DHCP setup help on AIR-WLC-2112 with LAP1042N

    I am new to wireless.  I would like to statically assign ip addresses for my controller(AIR_WLC-2112) and my access point (LAP1042N).  I would then like the controller to distribute dhcp addresses for users.  What is the best way in doing this? 

    Hi Mark,
    You can certainly setup your network for 2 VLANs for different wireless networks. You will only need to setup the switchports to the WLC as trunks. In other words, the APs will simply reside in the vlan you define (access switchports) and they will tunnel all traffic back to the controller, regardless of client vlan. The WLC will then determine which vlan the traffic needs to go on.
    You have 2 ways of setting your AP IP addresses as static -- you can statically assign them through the console during initial installation:
    capwap ap ip address
    capwap ap ip default-gateway
    capwap ap controller ip
    Or, you can simply let the APs start by using DHCP, and auto discovery of the WLCs via DNS lookup of "cisco-capwap-controller", or DHCP option 43. Once they join the controller you can assign them static addresses in the WLC AP settings.
    Now, onto the last question regarding your WAN sites. We do have options for you there as well -- the feature we're looking at would be H-REAP. Traditionally the APs tunnel all wireless traffic back to the controller. However, in H-REAP mode, you can specify the APs to put traffic on the network right at the local switch, so it wouldn't have to get tunneled across your WAN (depending on WAN bandwidth). You still configure the AP and manage it centrally. For more information on this feature, please check out the H-REAP deployment guide:
    http://www.cisco.com/en/US/products/ps10315/products_tech_note09186a0080736123.shtml
    -Patrick Croak
    Wireless TAC

  • WLC 2112 with 1042 Mesh APs

    Hello everybody,
    I have a Mesh architecture with 2112 WLC and 1042 APs
    I want just to know if I can connect one 1310 AP to the ethernet port of a mesh 1042 AP with ethernet bridging enabled.
    thanks

    Hello benhamzagi,
    Thank you for contacting the Sales Acceleration Center (SAC) regarding your recent inquiry, Case Number 80931
    Case Description:
    WLC 2112 with 1042 Mesh APs
    Case Solution:
    Here is the compatibility Matrix link
    http://www.cisco.com/en/US/docs/wireless/controller/5500/tech_notes/Wireless_Software_Compatibility_Matrix.html#wp118661
    Or the attach tables will help you base on Release, Controller, Mesh and AP
    Table 3 Controller Software Release and Controller Model Support Matrix
    Controller Model
    First Support
    Last Support
    2100
    4.2.x
    7.0.x
    2500
    7.0.x
    Cat3850
    3.2.0SE
    4400
    4.2.x
    7.0.x
    5500
    6.0.x
    5700
    3.2.0SE
    7500
    7.0.x
    8500
    7.3.x
    Virtual Controller
    7.3.x
    WiSM
    4.2.x
    7.0.x
    WiSM2 (1 DP)
    7.0.x
    WiSM2 (2 DP)
    7.2.x
    SRE
    7.0.x
    Table 4 Mesh and Controller Software Releases and the Supported APs
    Mesh and Controller Releases
    Supported Access Points
    7.4.x
    1522, 1524PS, 1524SB, 1552E, 1552H, 1552I, 1552C, 1552EU, 1552CU, 1552S, 1130, 1240, 1250, 1260, 1600, 2600, 3500e, 3500i, 3500p, 3600e, 3600i, 1140, 600 OEAP, AP801, AP802
    7.3.x
    1522, 1524PS, 1524SB, 1552E, 1552H, 1552I, 1552C, 1552EU, 1552CU, 1552S, 1130, 1240, 1250, 1260, 2600, 3500e, 3500i, 3600e, 3600i, 3500p, 1140, 600 OEAP, AP801, AP802
    7.2.11x.x
    1522, 1524PS, 1524SB, 1552E, 1552H, 1552I, 1552C, 1552S, 1130, 1240, 1250, 1260, 2600, 3500e, 3500i, 3500p, 3600e, 3600i, 1140, 600 OEAP, AP801, AP802
    7.2.10x.x
    1522, 1524PS, 1524SB, 1552E, 1552H, 1552I, 1552C, 1552S, 1130, 1240, 1250, 1260, 3500e, 3500i, 3600e, 3500p, 3600i, 1140, 600 OEAP, AP801, AP802
    7.0.2x.x
    1522, 1524PS, 1524SB, 1552E, 1552H, 1552I, 1552C, 1130, 1240, 1250, 1260, 3500e, 3500i, 3500p, 1140, 600 OEAP, AP801, AP802
    7.0.116.0
    1522, 1524PS, 1524SB, 1552E, 1552H, 1552I, 1552C, 1130, 1240, 1250, 1260, 3500e, 3500i, 3500p, 1140, 600 OEAP, AP801, AP802
    7.0.98.x
    1522, 1524PS, 1524SB, 1130, 1240
    6.0.202.0
    1522, 1524PS, 1524SB, 1130, 1240
    5.2.193.0
    1522, 1524PS, 1130, 1240
    4.1.192.35M (Mesh Release 3)
    1505, 1510, 1522, 1524PS, 1130, 1240
    4.1.191.24M (Mesh Release 2)
    1505, 1510, 1522 (US, Canada, and RoW), 1130, 1240
    4.1.190.5 (Mesh Release 1)
    1505, 1510, 1522 (US and Canada)
    As per your confirmation, I am going to close the case for this specific inquiry. We strive to provide you with excellent service. Please feel free to reach out to me or any member of the SAC team if we can be of any further assistance or if you have any other related questions in the future. We value your input and look forward to serving you moving forward.

  • When I plug in my Ipod touch to my computer a warning appears "The program cant start because MSVCR80.dll is missing."  I can not access my Itunes library.  Also, an "error 7 Windows error 126" appears as well.  Any ideas?

    When I plug in my Ipod Touch to my computer I can not access my Itunes library.  The following message appears "The program cant start because MSVCR80.dll is missing."  Also, another message appears as well - "Error 7  Windows error 126" as well as APSDaemon.exe.
    I have NO IDEA what the heck to do.
    Any ideas?
    Thanks!

    Issues installing iTunes or QuickTime for Windows
    solving MSVCR80
    iTunes 11.1.4 for Windows: Unable to install or open
    Troubleshooting issues with iTunes for Windows updates

  • TS4002 I bought iPad and I can not access, A message appears asking me account and password when i return to the person who I purchased it from him, he told me that he forgot the account and password I want a solution to the problem, because in this way I

    I bought iPad and I can not access, A message appears asking me account and password when i return to the person who I purchased it from him, he told me that he forgot the account and password
    I want a solution to the problem, because in this way I will not benefit from the iPad

    There is no solution.  You have to provide the ID and password.  There is no way around it.  If the person you bought it from can't provide it, return it and get your money back.

  • Can not access sample & admin tools after configuring Oracle8.1.7

    Hi all,
    I am using WLS6.1(sp2) and WLPortal4.0(sp1).
    I changed the default database(i.e. Cloudscape) to Oracle by following the doc
    http://edocs.bea.com/wlp/docs40/deploygd/oraclnew.htm
    But, after setting up the Oracle8.1.7, when i try to access the sample stock portal
    from the homepage, i am getting the following exception
    PortalPersistenceManager: portal 'portal/stockportal' not found
    <Feb 20, 2002 12:33:19 PM EST> <Error> <HTTP> <[WebAppServletContext(1467076,stockportal,/stockportal)]
    Servlet failed with S
    ervletException
    javax.servlet.ServletException: Received a null Portal object from the PortalManager.
    at com.bea.portal.appflow.servlets.internal.PortalWebflowServlet.setupPortalRequest(PortalWebflowServlet.java:194)
    at com.bea.portal.appflow.servlets.internal.PortalWebflowServlet.doGet(PortalWebflowServlet.java:99)
    at javax.servlet.http.HttpServlet.service(HttpServlet.java:740)
    at javax.servlet.http.HttpServlet.service(HttpServlet.java:853)
    at weblogic.servlet.internal.ServletStubImpl.invokeServlet(ServletStubImpl.java:265)
    at weblogic.servlet.internal.ServletStubImpl.invokeServlet(ServletStubImpl.java:200)
    at weblogic.servlet.internal.RequestDispatcherImpl.forward(RequestDispatcherImpl.java:241)
    at weblogic.servlet.jsp.PageContextImpl.forward(PageContextImpl.java:112)
    at jsp_servlet.__index._jspService(__index.java:92)
    at weblogic.servlet.jsp.JspBase.service(JspBase.java:27)
    at weblogic.servlet.internal.ServletStubImpl.invokeServlet(ServletStubImpl.java:265)
    at weblogic.servlet.internal.ServletStubImpl.invokeServlet(ServletStubImpl.java:200)
    at weblogic.servlet.internal.WebAppServletContext.invokeServlet(WebAppServletContext.java:2495)
    at weblogic.servlet.internal.ServletRequestImpl.execute(ServletRequestImpl.java:2204)
    at weblogic.kernel.ExecuteThread.execute(ExecuteThread.java:139)
    at weblogic.kernel.ExecuteThread.run(ExecuteThread.java:120)
    even i can not access the admin tools.....i get the follwing error when i try
    to access the portalTools/index.jsp
    <Feb 20, 2002 12:38:18 PM EST> <Warning> <Webflow> <Webflow could not resolve
    a destination given: appname [tools], namespace
    [admin_main], origin [begin], event [defaultEvent] with request id [3121877];
    Attempting to load Configuration-error-page.>
    <Feb 20, 2002 12:38:18 PM EST> <Error> <Webflow> <Error while parsing uri /portalTools/application,
    path null, query string n
    amespace=admin_main - Webflow XML does not exist, is not loaded properly, or you
    do not have a configuration-error-page defin
    ed.
    Exception[com.bea.p13n.appflow.exception.ConfigurationException: The configuration-error-page
    node was not found in the webfl
    ow xml file. for webapp [tools], namespace [admin_main]. While trying to display
    CONFIGURATION ERROR: [Exception[com.bea.p13n
    .appflow.exception.ConfigurationException: Bad Namespace - namespace [admin_main]
    is not available for webflow execution. Mak
    e sure the [admin_main.wf] file is deployed in webapp [tools].]],]
    at com.bea.p13n.appflow.webflow.internal.WebflowExecutorImpl.processConfigurationError(WebflowExecutorImpl.java:786)
    at com.bea.p13n.appflow.webflow.internal.WebflowExecutorImpl.processWebflowRequest(WebflowExecutorImpl.java:484)
    at com.bea.p13n.appflow.webflow.internal.WebflowExecutorImpl.processWebflowRequest(WebflowExecutorImpl.java:419)
    at com.bea.p13n.appflow.webflow.servlets.internal.WebflowServlet.doGet(WebflowServlet.java:132)
    at javax.servlet.http.HttpServlet.service(HttpServlet.java:740)
    at javax.servlet.http.HttpServlet.service(HttpServlet.java:853)
    at weblogic.servlet.internal.ServletStubImpl.invokeServlet(ServletStubImpl.java:265)
    at weblogic.servlet.internal.ServletStubImpl.invokeServlet(ServletStubImpl.java:200)
    at weblogic.servlet.internal.RequestDispatcherImpl.forward(RequestDispatcherImpl.java:241)
    at weblogic.servlet.jsp.PageContextImpl.forward(PageContextImpl.java:112)
    at jsp_servlet.__index._jspService(__index.java:92)
    at weblogic.servlet.jsp.JspBase.service(JspBase.java:27)
    at weblogic.servlet.internal.ServletStubImpl.invokeServlet(ServletStubImpl.java:265)
    at weblogic.servlet.internal.ServletStubImpl.invokeServlet(ServletStubImpl.java:200)
    at weblogic.servlet.internal.WebAppServletContext.invokeServlet(WebAppServletContext.java:2495)
    at weblogic.servlet.internal.ServletRequestImpl.execute(ServletRequestImpl.java:2204)
    at weblogic.kernel.ExecuteThread.execute(ExecuteThread.java:139)
    at weblogic.kernel.ExecuteThread.run(ExecuteThread.java:120)
    >
    Am i missing any step here???
    can anybody help me????
    thanks
    Vijay

    oops...i missed step5.
    it is working now after doing the sync.
    thanks
    Vijay
    "Daniel Selman" <[email protected]> wrote:
    Did you sync the applications and load the sample data?
    Sincerely,
    Daniel Selman
    "vijay bujula" <[email protected]> wrote in message
    news:[email protected]...
    Hi all,
    I am using WLS6.1(sp2) and WLPortal4.0(sp1).
    I changed the default database(i.e. Cloudscape) to Oracle by followingthe
    doc
    http://edocs.bea.com/wlp/docs40/deploygd/oraclnew.htm
    But, after setting up the Oracle8.1.7, when i try to access the samplestock portal
    from the homepage, i am getting the following exception
    PortalPersistenceManager: portal 'portal/stockportal' not found
    <Feb 20, 2002 12:33:19 PM EST> <Error> <HTTP><[WebAppServletContext(1467076,stockportal,/stockportal)]
    Servlet failed with S
    ervletException
    javax.servlet.ServletException: Received a null Portal object fromthe
    PortalManager.
    atcom.bea.portal.appflow.servlets.internal.PortalWebflowServlet.setupPortalReq
    uest(PortalWebflowServlet.java:194)
    atcom.bea.portal.appflow.servlets.internal.PortalWebflowServlet.doGet(PortalWe
    bflowServlet.java:99)
    at javax.servlet.http.HttpServlet.service(HttpServlet.java:740)
    at javax.servlet.http.HttpServlet.service(HttpServlet.java:853)
    atweblogic.servlet.internal.ServletStubImpl.invokeServlet(ServletStubImpl.java
    :265)
    atweblogic.servlet.internal.ServletStubImpl.invokeServlet(ServletStubImpl.java
    :200)
    atweblogic.servlet.internal.RequestDispatcherImpl.forward(RequestDispatcherImp
    l.java:241)
    atweblogic.servlet.jsp.PageContextImpl.forward(PageContextImpl.java:112)
    at jsp_servlet.__index._jspService(__index.java:92)
    at weblogic.servlet.jsp.JspBase.service(JspBase.java:27)
    atweblogic.servlet.internal.ServletStubImpl.invokeServlet(ServletStubImpl.java
    :265)
    atweblogic.servlet.internal.ServletStubImpl.invokeServlet(ServletStubImpl.java
    :200)
    atweblogic.servlet.internal.WebAppServletContext.invokeServlet(WebAppServletCo
    ntext.java:2495)
    atweblogic.servlet.internal.ServletRequestImpl.execute(ServletRequestImpl.java
    :2204)
    at weblogic.kernel.ExecuteThread.execute(ExecuteThread.java:139)
    at weblogic.kernel.ExecuteThread.run(ExecuteThread.java:120)
    even i can not access the admin tools.....i get the follwing errorwhen i
    try
    to access the portalTools/index.jsp
    <Feb 20, 2002 12:38:18 PM EST> <Warning> <Webflow> <Webflow could notresolve
    a destination given: appname [tools], namespace
    [admin_main], origin [begin], event [defaultEvent] with request id[3121877];
    Attempting to load Configuration-error-page.>
    <Feb 20, 2002 12:38:18 PM EST> <Error> <Webflow> <Error while parsinguri
    /portalTools/application,
    path null, query string n
    amespace=admin_main - Webflow XML does not exist, is not loaded properly,or you
    do not have a configuration-error-page defin
    ed.
    Exception[com.bea.p13n.appflow.exception.ConfigurationException: The
    configuration-error-page>> node was not found in the webfl>> ow xml file. for webapp [tools, namespace [admin_main]. While tryingto
    display
    CONFIGURATION ERROR: [Exception[com.bea.p13n
    appflow.exception.ConfigurationException: Bad Namespace - namespace[admin_main]
    is not available for webflow execution. Mak
    e sure the [admin_main.wf] file is deployed in webapp [tools].]],]
    atcom.bea.p13n.appflow.webflow.internal.WebflowExecutorImpl.processConfigurati
    onError(WebflowExecutorImpl.java:786)
    atcom.bea.p13n.appflow.webflow.internal.WebflowExecutorImpl.processWebflowRequ
    est(WebflowExecutorImpl.java:484)
    atcom.bea.p13n.appflow.webflow.internal.WebflowExecutorImpl.processWebflowRequ
    est(WebflowExecutorImpl.java:419)
    atcom.bea.p13n.appflow.webflow.servlets.internal.WebflowServlet.doGet(WebflowS
    ervlet.java:132)
    at javax.servlet.http.HttpServlet.service(HttpServlet.java:740)
    at javax.servlet.http.HttpServlet.service(HttpServlet.java:853)
    atweblogic.servlet.internal.ServletStubImpl.invokeServlet(ServletStubImpl.java
    :265)
    atweblogic.servlet.internal.ServletStubImpl.invokeServlet(ServletStubImpl.java
    :200)
    atweblogic.servlet.internal.RequestDispatcherImpl.forward(RequestDispatcherImp
    l.java:241)
    atweblogic.servlet.jsp.PageContextImpl.forward(PageContextImpl.java:112)
    at jsp_servlet.__index._jspService(__index.java:92)
    at weblogic.servlet.jsp.JspBase.service(JspBase.java:27)
    atweblogic.servlet.internal.ServletStubImpl.invokeServlet(ServletStubImpl.java
    :265)
    atweblogic.servlet.internal.ServletStubImpl.invokeServlet(ServletStubImpl.java
    :200)
    atweblogic.servlet.internal.WebAppServletContext.invokeServlet(WebAppServletCo
    ntext.java:2495)
    atweblogic.servlet.internal.ServletRequestImpl.execute(ServletRequestImpl.java
    :2204)
    at weblogic.kernel.ExecuteThread.execute(ExecuteThread.java:139)
    at weblogic.kernel.ExecuteThread.run(ExecuteThread.java:120)
    >
    Am i missing any step here???
    can anybody help me????
    thanks
    Vijay

  • Can not access server's on public ip's

    Guys,
    We have a core switch with two fibre lines connecting us through two different ISP's to the internet. These ISP's have provided us with a range of public ip's each. We have a few routers on some of these ip's and they are working fine and we can access them externally (telnet and ssh).
    I am now busy setting up two servers, one on each ISP with their respective public ip's. I can ping the core switch and the isp gateways from the servers and from the core. I have triple checked that there are no active firewalls and I can see that the http ports are open and accessible (TcpView). But for the life of me I can not access those servers externally. I am now completely stumped. I do suspect though that it is a routing problem through the core.
    And herewith the relevant parts from my Core switch's config:
    version 12.2
    service tcp-keepalives-in
    service tcp-keepalives-out
    hostname SMS-CORE
    no aaa new-model
    clock timezone ZAR 2
    no ip source-route
    mls netflow interface
    mls cef error action reset
    spanning-tree mode pvst
    spanning-tree portfast edge default
    vlan internal allocation policy ascending
    interface FastEthernet3/25
     switchport
     switchport access vlan 153
     switchport mode access
    interface FastEthernet3/31
     switchport
     switchport access vlan 153
     switchport mode access
    interface FastEthernet3/35
     switchport
     switchport access vlan 153
     switchport mode access
    interface FastEthernet3/37
     switchport
     switchport access vlan 20
     switchport mode access
    interface FastEthernet3/47
     switchport
     switchport access vlan 20
     switchport mode access
    interface FastEthernet3/48
     ip address 192.168.2.2 255.255.255.252
    interface Vlan1
     no ip address
    interface Vlan20
     ip address PUBLIC_IP1 255.255.255.240
    interface Vlan153
     ip address PUBLIC_IP2 255.255.255.248
    ip classless
    ip route 0.0.0.0 0.0.0.0 192.168.2.1
    ip local policy route-map PUBLIC
    access-list 100 permit ip ISP2_NETWORK 0.0.0.7 any
    access-list 101 permit ip ISP1_NETWORK 0.0.0.15 any
    route-map PUBLIC permit 10
     match ip address 100
     set ip default next-hop PUBLIC_GW2
    route-map PUBLIC permit 20
     match ip address 101
     set ip default next-hop 192.168.2.1
    Any  ideas guys, I am at my wits end here ....
    Thanks as always !

    Hi Oliver , 
           Have you got IP Address assigned to your server from the same segment ?? like for server 1 
    ip address PUBLIC_IP1 255.255.255.240
    and for server 2 
    ip address PUBLIC_IP2 255.255.255.248
    What is the gateway IP address assigned for both servers .
    HTH
    Sandy

  • Can not access Server admin site

    I can not access http://MYSERVER1:50000 site. I get error "The page cannot be displayed. The page you are looking for is currently unavailable.".
    But I was able to access even yesterday. Could you tell me any possible problems and how to fix the error?
    Thanks!
    Mike

    Hi Mike
    That means your J2EE engine is not running...
    Restart the engine, also check that the DB is up and running.
    Regards
    Juan

  • Can not access BIOS after update BIOS

    Can not access BIOS after update X220 BIOS to version 1.19
    Type: 4290-R32
    BIOS: 1.19
    http://download.lenovo.com/ibmdl/pub/pc/pccbbs/mobiles/8duj09uc.txt
    http://download.lenovo.com/ibmdl/pub/pc/pccbbs/mobiles/8duj09uc.iso
    Ask google and try anyway but not work
    - Press ThinkVantage, Press F1, Press Fn+F1
    - Power off, unplug AC, unplug battery, wait 15 miniute, try all again
    - Try to update BIOS again

    That is really weird.
    When you are in Windows, can you test and see if the F1 key is working? If it is working. Shut down the laptop then boot it back up. At the Thinkpad screen, keep spamming the F1 key and see if you are able to boot into BIOS.
    //JameZ
    Check out the Community Knowledge Base for hints and tips.
    Did someone help you today? Press the star on the left to thank them with a Kudo!
    If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"!
    X240 | 8GB RAM | 512GB Samsung SSD

  • Can not access the Instance Data of a Singleton class from MBean

    I am working against the deadline and i am sweating now. From past few days i have been working on a problem and now its the time to shout out.
    I have an application (let's call it "APP") and i have a "PerformanceStatistics" MBean written for APP. I also have a Singleton Data class (let's call it "SDATA") which provides some data for the MBean to access and calculate some application runtime stuff. Thus during the application startup and then in the application lifecysle, i will be adding data to the SDATA instance.So, this SDATA instance always has the data.
    Now, the problem is that i am not able to access any of the data or data structures from the PerformanceStatistics MBean. if i check the data structures when i am adding the data, all the structures contains data. But when i call this singleton instance from the MBean, am kind of having the empty data.
    Can anyone explain or have hints on what's happening ? Any help will be appreciated.
    I tried all sorts of DATA class being final and all methods being synchronized, static, ect.,, just to make sure. But no luck till now.
    Another unfortunate thing is that, i some times get different "ServicePerformanceData " instances (i.e. when i print the ServicePerformanceData.getInstance() they are different at different times). Not sure whats happening. I am running this application in WebLogic server and using the JConsole.
    Please see the detailed problem at @ http://stackoverflow.com/questions/1151117/can-not-access-the-instance-data-of-a-singleton-class-from-mbean
    I see related problems but no real solutions. Appreciate if anyone can throw in ideas.
    http://www.velocityreviews.com/forums/t135852-rmi-singletons-and-multiple-classloaders-in-weblogic.html
    http://www.theserverside.com/discussions/thread.tss?thread_id=12194
    http://www.jguru.com/faq/view.jsp?EID=1051835
    Thanks,
    Krishna

    I am working against the deadline and i am sweating now. From past few days i have been working on a problem and now its the time to shout out.
    I have an application (let's call it "APP") and i have a "PerformanceStatistics" MBean written for APP. I also have a Singleton Data class (let's call it "SDATA") which provides some data for the MBean to access and calculate some application runtime stuff. Thus during the application startup and then in the application lifecysle, i will be adding data to the SDATA instance.So, this SDATA instance always has the data.
    Now, the problem is that i am not able to access any of the data or data structures from the PerformanceStatistics MBean. if i check the data structures when i am adding the data, all the structures contains data. But when i call this singleton instance from the MBean, am kind of having the empty data.
    Can anyone explain or have hints on what's happening ? Any help will be appreciated.
    I tried all sorts of DATA class being final and all methods being synchronized, static, ect.,, just to make sure. But no luck till now.
    Another unfortunate thing is that, i some times get different "ServicePerformanceData " instances (i.e. when i print the ServicePerformanceData.getInstance() they are different at different times). Not sure whats happening. I am running this application in WebLogic server and using the JConsole.
    Please see the detailed problem at @ http://stackoverflow.com/questions/1151117/can-not-access-the-instance-data-of-a-singleton-class-from-mbean
    I see related problems but no real solutions. Appreciate if anyone can throw in ideas.
    http://www.velocityreviews.com/forums/t135852-rmi-singletons-and-multiple-classloaders-in-weblogic.html
    http://www.theserverside.com/discussions/thread.tss?thread_id=12194
    http://www.jguru.com/faq/view.jsp?EID=1051835
    Thanks,
    Krishna

  • I'm note a firefox geek, but ever since my friend told me to install NoScript I can not access my msn and hotmail page. It tells me that Java Script is required, what ever that is. What do I do next. Do I uninstall the No Script. Thanks Ed

    I'm note a firefox geek, but ever since my friend told me to install NoScript I can not access my msn and hotmail page. It tells me that Java Script is required, what ever that is. What do I do next. Do I uninstall the No Script. Thanks Ed edit
    Details

    You are on Windows 2000, you do not have a "Firefox" button, and should consider yourself to be fortunate in that you still have menus and don't have to do anything to get the menus back instead of the "Firefox" button. (The same applies to Windows XP users).
    Use the "File" menu to get to Import. You are not on Windows 7 or Vista, and don't have to put up with the nonsense added for Aero.
    If you want the "Firefox" button you can get it with View -> toolbars -> (uncheck) Menu Bar. The menu bar and the "Firefox" button were supposed to be mutually exclusive (which is impossible in some cases without being incompatible).
    Once you are using the "Firefox" button ...
    Use the "Alt" key to view the menu bar (temporarily) containing File, Edit, View, History, Bookmarks, Tools, and Help. On Windows 7 and Vista, the menu bar was hidden by default in Firefox 4 and above. These menu items are more or less available under the "Firefox" button which has the most used of the built-in Firefox menu items available in a different format.
    To get back to having menus again. "Firefox" button -> Options (second column) -> (check) Menu Bar
    You can make '''Firefox 7.0.1''' look like Firefox 3.6.*, see numbered '''items 1-10''' in the following topic [http://dmcritchie.mvps.org/firefox/firefox-problems.htm#fx4interface Fix Firefox 4.0 toolbar user interface, problems (Make Firefox 4.0 thru 8.0, look like 3.6)]. ''Whether or not you make changes, you should be aware of what has changed and what you have to do to use changed or missing features.''
    * http://dmcritchie.mvps.org/firefox/firefox-problems.htm#fx4interface

  • Can not access the media card files Blackberry 8310 - HELP

    Can not access the media card files Blackberry 8310.
     I had a battery drain problem. The unit would only last 16 hours before completely drained. Purchased a new battery with the same result. I figured that I should try a complete reset so I did a hard wipe. Once that was done and I loaded the unit back up and returned online, the battery drain problem was resolved but now I can not access the media card.
     Here are the messages:
     “A media card has been inserted that contains encrypted content which will be unaccessible by this device”
     I can see the files. I have transferred them to my PC via the SD card but I can not open them. Here are the settings:
     Media card support – ON
    Encryption Mode: - Security Password & Device
    Encrypt Media Files – YES
    Mass Storage Mode Support – OFF
     Please note – I can not change the encryption mode since it is set by policy
     Security Options – General Settings – Content Protection – Disabled
     The version of Desktop Manage I am using is 4.2.1.8. When I try to use the Media Manager to move the files, I get an error message and can’t move the file. If I access the file on the card and try to display it, I get:
     Unable to display file /media card/ pictures/ing000000xx.jpg.rem
     Here is what I have tried (from the advice on this board):
     1)     Read the files directly off the media card – No good
    2)     Create a “new” folder on the media card and move a file into it then try to read it – No good
    3)     Email the file then read it – No good
    4)     Reset Encryption mode to off then try – Can’t do it – IT Policy setting
    5)     Be sure that the password was set the same as before the wipe (setting is password & device) – Can’t do it – The Blackberry prevents me from using an old password.
     So I think I can’t read the files because I can’t replicate the encryption key. Could that be right? My problem is that I do not understand why this would be the case. It is still the same device and since it knows what the old password was (because it would prevent me from using it again), why would it not generate a key to access the files?
     All I am trying to get off the card are pictures on my 6 year old … some are priceless. Can someone help me do this? One would think that this should not be this hard but from all the postings I have found, it seems that it is. And yes, shame on me for not moving the files before I did the reset (THAT will never happen again!) but this being unrecoverable is unconscionable given how many seem to find themselves in this situation.
     Thanks for any help you can offer!

    Not sure why you couldn't see them using mass storage mode. Did you have the pics stored on your media card? Try going to media-menu-explore-media card-blackberry-pictures See what the extension is on your pics. If any have the extension such as .jpg.rem they are encrypted.
    IrwinII
    Please remember to "Accept as Solution" the post which solved your thread. If I or someone else have helped you, please tell us you "Like" what we had to say at the bottom right of the post.

  • Firefox will not automatically load Tiscali and after I have loaded using START it will not access my e-mails on tiscali

    Until I loaded the latest version of Firefox I accessed Tiscali without difficulty usong the Icon. Now it will not access the internet at all and I have to use Windows to access the internet. Tiscali then loads but i cannot access my e-mails and I get a message telling me I have 'undefined e-mails'. Windows Explorer works perfectly

    Hi again,
    Helps if I give the correct link ! <br/>The press shift button appears to still work, but the option to start in safe mode from the programs listing of a standard install I do not think exists anymore.
    Safe mode will start from a command line, (or a shortcut) and in some circumstances you may need to enter the full path name on a command or shortcut detailed instructions are at http://kb.mozillazine.org/Safe_mode
    Remember (at least at this stage) do not make changes when you get the options list, just click on the continue button.
    If you think that RealPlayer is causing the problem you could uninstall that for now.
    Firefox recent versions are 3.6 4.0 (and 5.0 in beta). There is some debate as to whether creating new profiles or re-installing Firefox is the simplest method of troubleshooting and solving some of these problems, personally I use multiple profiles and multiple versions of Firefox, and tend to forget the required procedures are less than straightforward. For now at least try [[safe mode]] again.
    * see also Instructions for [[installing a previous version of firefox]]

Maybe you are looking for