WLC 2500 series
As far as I can find this model comes with 4 X Gigabit ports but does not support Etherchannel or LAG .. .. can someone confirm this ? I assume this is this a hardware limitation since it uses the 7.0 code as the 5508 series right ?
Correct, the 2500 does not support LAG/Etherchannel.
"An interface is a logical entity on the controller. An interface has multiple parameters associated with it, including IP address, default-gateway (for the IP subnet), primary physical port, secondary physical port, VLAN tag, and DHCP server. Since LAG is not used, each interface is mapped to at least one primary physical port and an optional secondary port. Multiple interfaces can be mapped to a single Wireless Controller port."
From here: http://www.cisco.com/en/US/customer/products/ps11630/products_tech_note09186a0080b8450c.shtml#cliconfig
Similar Messages
-
Splash Page in WLC 2500 Series
Can someone tell me if there is Splash Page feature in the 2500 WLC ? I cannot find any Cisco document which says it has that feature ?
Yes, Its available.
Here is a link that points to a configuration guide for a wlc 2500, 7.5.
http://www.cisco.com/c/en/us/td/docs/wireless/controller/7-5/config_guide/b_cg75.pdf
"The splash page web redirect feature is available only for WLANs that are configured for 802.1X or
WPA+WPA2 Layer 2 security with 802.1x key management." -
Does WLC 2500 series spupports 1262 series Access Point?
Does AIR-CT2504-25-K9 spupports AIR-LAP1262N-E-K9 Access Point? How can I check this?
AFAIK, the 2504 supports anything in the 7.0.116.0 Release Note. It should be called out in the release note if the 2504 does not support anything in particular.
Since the 1262 is the non CleanAir version of the 3502e, which is only availabile in 7.0+ anyhow, I would have to imagine it is supported in the new WLC. -
WLC 2500 Series: differences between 7.0 and 7.2 Firmwares?
Hello everybody.
I'm quite new to Cisco WLAN Controllers, thus I'm asking now (as I have to configure one from ground on): which differences exist between 7.0 and 7.2 firmwares? I have to decide/choose which of them to run, before continuing to configure my WLAN infrastructure.
Thanks in advance and kind regards,
F.If this is a brand new install the answer is simple in my mind, go with 7.2. There are a lot of neat features in 7.2 that are not in 7.0, plus 7.0 is on maintenance releases only now, 7.2 is the new main code for supporting the newer WLCs. Besides TAC generally wants you to upgrade to the latest if you call them for help so you might as well get started on the new code now when you don't have to worry about bringing the networks down to upgrade.
Sent from Cisco Technical Support iPad App -
Is it possible to have 2500 series management interface out of band of APs?
I currently have 2500 series WLCs. Our wireless network is completely separate from our internal network, keeping the WLC from talking to any internal servers. The company would like to start using AD(LDAP authentication) for end users while still keeping the APs on a completely separate network. Since the 2500 series does not support a "service port", Is there any way to move the management port out-of-band with no access to APs and just use the other ports for AP management?
I haven't had my morning coffee ... But let me give this a shot..
I am going to say no. The managment interface is needed for APs to join. If you isloate this interface no APs can join. Even if AP managers are used, the AP requries to touch the managment interface when booting up.
"Satisfaction does not come from knowing the solution, it comes from knowing why." - Rosalind Franklin
"I'm in a serious relationship with my Wi-Fi. You could say we have a connection."
"Im like bacon, I make your wireless better" -
Hi,
I have successfully connected my WLC 2500 controller with 20 light weight Access points 1262N.
I have used the internal DHCP server option in the controller for the AP's and client.
Port 1 of the WLC is trunked with the switch 2960. All is working fine
The problem comes when I remove the Ethernet cable from the management interface and restart the WLC. The AP's don't come back. If I don't restart the WLC the AP's remain.
On the other hand, when I leave the Ethernet cable connected to the management port with my pc and then reboot the WLC, the AP's appear.
Seems like whenever im not physically connected to the management port of the WLC and restart it, the AP's don't come back. The only way to make them come back again is to connect my PC to the management port.
Please help me. What seems to be the problem here ?
Best Regards,Hi,
All 20 Pc;s are in one area connected to the same AP im assuming. The PC;s are stationary, so didnt check for roaming, but generally my laptop connectivity is fine while roaming. It rarely disconnects but users have complained that it did disconncect a few times.
Please see below the WLC configuration:
User:Dawaa
Password:********
(Cisco Controller) >sh
(Cisco Controller) show>running-config
Notice: "show running-config" has been changed to be an alias to "show run-config".
Use "show run-config commands" to display the configuration commands.
Press Enter to continue or to abort...
System Inventory
NAME: "Chassis" , DESCR: "Cisco 2500 Series Wireless LAN Controller"
PID: AIR-CT2504-K9, VID: V01, SN: PSZ163602PD
Burned-in MAC Address............................ 20:3A:07:67:C3:00
Maximum number of APs supported.................. 15
Press Enter to continue or to abort
System Information
Manufacturer's Name.............................. Cisco Systems Inc.
Product Name..................................... Cisco Controller
Product Version.................................. 7.3.101.0
Bootloader Version............................... 1.0.16
Field Recovery Image Version..................... 1.0.0
Firmware Version................................. PIC 16.0
Build Type....................................... DATA + WPS
System Name...................................... tEthernet0
System Location..................................
System Contact...................................
System ObjectID.................................. 1.3.6.1.4.1.9.1.1279
IP Address....................................... 192.168.0.140
Last Reset....................................... Software reset
System Up Time................................... 0 days 1 hrs 23 mins 40 secs
System Timezone Location......................... (GMT +3:00) Baghdad
Configured Country............................... SA - Saudi Arabia
Operating Environment............................ Commercial (0 to 40 C)
--More or (q)uit current module or to abort
Internal Temp Alarm Limits....................... 0 to 65 C
Internal Temperature............................. +26 C
External Temperature............................. +30 C
Fan Status....................................... 4200 rpm
State of 802.11b Network......................... Enabled
State of 802.11a Network......................... Enabled
Number of WLANs.................................. 1
Number of Active Clients......................... 10
Burned-in MAC Address............................ 20:3A:07:67:C3:00
Maximum number of APs supported.................. 15
Press Enter to continue or to abort
AP Bundle Information
Primary AP Image Size
ap1g2 10596
ap3g1 11088
ap3g2 10968
ap801 7092
ap802 8428
c1130 5072
c1140 9288
c1250 6784
c1520 7852
c602i 3736
Secondary AP Image Size
ap1g2 10596
ap3g1 11088
ap3g2 10968
ap801 7092
ap802 8428
--More or (q)uit current module or to abort
c1130 5072
c1140 9288
c1250 6784
c1520 7852
c602i 3736
Press Enter to continue or to abort
Switch Configuration
802.3x Flow Control Mode......................... Disable
FIPS prerequisite features....................... Disabled
secret obfuscation............................... Enabled
Strong Password Check Features:
case-check ...........Enabled
consecutive-check ....Enabled
default-check .......Enabled
username-check ......Enabled
Press Enter to continue or to abort
Network Information
RF-Network Name............................. Dawaa
Web Mode.................................... Enable
Secure Web Mode............................. Enable
Secure Web Mode Cipher-Option High.......... Disable
Secure Web Mode Cipher-Option SSLv2......... Disable
Secure Web Mode RC4 Cipher Preference....... Disable
OCSP........................................ Disabled
OCSP responder URL..........................
Secure Shell (ssh).......................... Enable
Telnet...................................... Enable
Ethernet Multicast Forwarding............... Disable
Ethernet Broadcast Forwarding............... Disable
AP Multicast/Broadcast Mode................. Multicast Address : 239.60.60.60
IGMP snooping............................... Disabled
IGMP timeout................................ 60 seconds
IGMP Query Interval......................... 20 seconds
MLD snooping................................ Disabled
MLD timeout................................. 60 seconds
MLD query interval.......................... 20 seconds
User Idle Timeout........................... 300 seconds
ARP Idle Timeout............................ 300 seconds
--More or (q)uit current module or to abort
Cisco AP Default Master..................... Enabled
AP Join Priority............................ Disable
Mgmt Via Wireless Interface................. Enable
Mgmt Via Dynamic Interface.................. Enable
Bridge MAC filter Config.................... Enable
Bridge Security Mode........................ EAP
Mesh Full Sector DFS........................ Enable
AP Fallback ................................ Enable
Web Auth Redirect Ports .................... 80
Web Auth Proxy Redirect ................... Disable
Web Auth Captive-Bypass .................. Disable
Web Auth Secure Web ....................... Enable
Fast SSID Change ........................... Disabled
AP Discovery - NAT IP Only ................. Enabled
IP/MAC Addr Binding Check .................. Enabled
CCX-lite status ............................ Disable
oeap-600 dual-rlan-ports ................... Disable
oeap-600 local-network ..................... Enable
Press Enter to continue or to abort
Port Summary
STP Admin Physical Physical Link Link
Pr Type Stat Mode Mode Status Status Trap POE
1 Normal Forw Enable Auto 1000 Full Up Enable N/A
2 Normal Disa Enable Auto Auto Down Enable N/A
3 Normal Disa Enable Auto Auto Down Enable Enable (Power Off)
4 Normal Disa Enable Auto Auto Down Enable Enable (Power Off)
Press Enter to continue or to abort
AP Summary
Number of APs.................................... 14
Global AP User Name.............................. Not Configured
Global AP Dot1x User Name........................ Not Configured
AP Name Slots AP Model Ethernet MAC Location Port Country Priority
AP6c20.56a0.b352 2 AIR-LAP1262N-E-K9 6c:20:56:a0:b3:52 default location 1 SA 1
AP6c20.5666.e34a 2 AIR-LAP1262N-E-K9 6c:20:56:66:e3:4a default location 1 SA 1
AP6c20.56a0.b341 2 AIR-LAP1262N-E-K9 6c:20:56:a0:b3:41 default location 1 SA 1
AP6c20.56a0.b4db_(Expiry) 2 AIR-LAP1262N-E-K9 6c:20:56:a0:b4:db Expiry Warehouse 1 SA 1
AP6c20.569a.59da 2 AIR-LAP1262N-E-K9 6c:20:56:9a:59:da default location 1 SA 1
AP6c20.5666.e2db 2 AIR-LAP1262N-E-K9 6c:20:56:66:e2:db default location 1 SA 1
AP6c20.568c.d530_(Expiry) 2 AIR-LAP1262N-E-K9 6c:20:56:8c:d5:30 default location 1 SA 1
AP6c20.5666.e2ca 2 AIR-LAP1262N-E-K9 6c:20:56:66:e2:ca default location 1 SA 1
AP6c20.5666.e354 2 AIR-LAP1262N-E-K9 6c:20:56:66:e3:54 default location 1 SA 1
AP6c20.569a.59fd 2 AIR-LAP1262N-E-K9 6c:20:56:9a:59:fd default location 1 SA 1
AP6c20.56a0.b346 2 AIR-LAP1262N-E-K9 6c:20:56:a0:b3:46 default location 1 SA 1
AP6c20.56a0.b2f0 2 AIR-LAP1262N-E-K9 6c:20:56:a0:b2:f0 default location 1 SA 1
AP6c20.568c.d1ec 2 AIR-LAP1262N-E-K9 6c:20:56:8c:d1:ec default location 1 SA 1
AP6c20.56a0.b425 2 AIR-LAP1262N-E-K9 6c:20:56:a0:b4:25 default location 1 SA 1
--More or (q)uit current module or to abort
AP Tcp-Mss-Adjust Info
AP Name TCP State MSS Size
AP6c20.56a0.b352 disabled -
AP6c20.5666.e34a disabled -
AP6c20.56a0.b341 disabled -
AP6c20.56a0.b4db_(Expiry) disabled -
AP6c20.569a.59da disabled -
AP6c20.5666.e2db disabled -
AP6c20.568c.d530_(Expiry) disabled -
AP6c20.5666.e2ca disabled -
AP6c20.5666.e354 disabled -
AP6c20.569a.59fd disabled -
AP6c20.56a0.b346 disabled -
AP6c20.56a0.b2f0 disabled -
AP6c20.568c.d1ec disabled -
AP6c20.56a0.b425 disabled -
Press Enter to continue or to abort
AP Location
Total Number of AP Groups........................ 0
Site Name........................................ default-group
Site Description.................................
AP Operating Class............................... Not-configured
RF Profile
2.4 GHz band.....................................
5 GHz band.......................................
WLAN ID Interface Network Admission Control Radio Policy
1 management Disabled None
AP Name Slots AP Model Ethernet MAC Location Port Country Priority
AP6c20.56a0.b352 2 AIR-LAP1262N-E-K9 6c:20:56:a0:b3:52 default location 1 SA 1
AP6c20.5666.e34a 2 AIR-LAP1262N-E-K9 6c:20:56:66:e3:4a default location 1 SA 1
AP6c20.56a0.b341 2 AIR-LAP1262N-E-K9 6c:20:56:a0:b3:41 default location 1 SA 1
AP6c20.56a0.b4db_(Expiry) 2 AIR-LAP1262N-E-K9 6c:20:56:a0:b4:db Expiry Warehouse 1 SA 1
--More or (q)uit current module or to abort
AP6c20.569a.59da 2 AIR-LAP1262N-E-K9 6c:20:56:9a:59:da default location 1 SA 1
AP6c20.5666.e2db 2 AIR-LAP1262N-E-K9 6c:20:56:66:e2:db default location 1 SA 1
AP6c20.568c.d530_(Expiry) 2 AIR-LAP1262N-E-K9 6c:20:56:8c:d5:30 default location 1 SA 1
AP6c20.5666.e2ca 2 AIR-LAP1262N-E-K9 6c:20:56:66:e2:ca default location 1 SA 1
AP6c20.5666.e354 2 AIR-LAP1262N-E-K9 6c:20:56:66:e3:54 default location 1 SA 1
AP6c20.569a.59fd 2 AIR-LAP1262N-E-K9 6c:20:56:9a:59:fd default location 1 SA 1
AP6c20.56a0.b346 2 AIR-LAP1262N-E-K9 6c:20:56:a0:b3:46 default location 1 SA 1
AP6c20.56a0.b2f0 2 AIR-LAP1262N-E-K9 6c:20:56:a0:b2:f0 default location 1 SA 1
AP6c20.568c.d1ec 2 AIR-LAP1262N-E-K9 6c:20:56:8c:d1:ec default location 1 SA 1
AP6c20.56a0.b425 2 AIR-LAP1262N-E-K9 6c:20:56:a0:b4:25 default location 1 SA 1
Press Enter to continue or to abort
RF Profile
Number of RF Profiles............................ 0
Out Of Box State................................. Disabled
RF Profile Name Band Description Applied
Press Enter to continue or to abort
AP Config
Cisco AP Identifier.............................. 0
Cisco AP Name.................................... AP6c20.56a0.b352
Country code..................................... SA - Saudi Arabia
Regulatory Domain allowed by Country............. 802.11bg:-AE 802.11a:-E
AP Country code.................................. SA - Saudi Arabia
AP Regulatory Domain............................. -E
Switch Port Number .............................. 1
MAC Address...................................... 6c:20:56:a0:b3:52
IP Address Configuration......................... DHCP
IP Address....................................... 192.168.0.111
IP NetMask....................................... 255.255.255.0
Gateway IP Addr.................................. 192.168.0.220
NAT External IP Address.......................... None
CAPWAP Path MTU.................................. 1485
Telnet State..................................... Disabled
Ssh State........................................ Disabled
Cisco AP Location................................ default location
Cisco AP Group Name.............................. default-group
Primary Cisco Switch Name........................
Primary Cisco Switch IP Address.................. Not Configured
Secondary Cisco Switch Name......................
--More or (q)uit current module or to abort
Secondary Cisco Switch IP Address................ Not Configured
Tertiary Cisco Switch Name.......................
Tertiary Cisco Switch IP Address................. Not Configured
Administrative State ............................ ADMIN_ENABLED
Operation State ................................. REGISTERED
Mirroring Mode .................................. Disabled
AP Mode ......................................... Local
Public Safety ................................... Disabled
AP SubMode ...................................... Not Configured
Remote AP Debug ................................. Disabled
Logging trap severity level ..................... informational
Logging syslog facility ......................... kern
S/W Version .................................... 7.3.101.0
Boot Version ................................... 12.4.2.4
Mini IOS Version ................................ 7.3.1.73
Stats Reporting Period .......................... 180
LED State........................................ Enabled
PoE Pre-Standard Switch.......................... Disabled
PoE Power Injector MAC Addr...................... Disabled
Power Type/Mode.................................. Power injector / Normal mode
Number Of Slots.................................. 2
AP Model......................................... AIR-LAP1262N-E-K9
AP Image......................................... C1260-K9W8-M
--More or (q)uit current module or to abort
IOS Version...................................... 15.2(2)JA$
Reset Button..................................... Enabled
AP Serial Number................................. FCZ1642Z0A6
AP Certificate Type.............................. Manufacture Installed
AP User Mode..................................... CUSTOMIZED
AP User Name..................................... dawaa
AP Dot1x User Mode............................... Not Configured
AP Dot1x User Name............................... Not Configured
Cisco AP system logging host..................... 255.255.255.255
AP Up Time....................................... 0 days, 22 h 01 m 44 s
AP LWAPP Up Time................................. 0 days, 01 h 25 m 37 s
Join Date and Time............................... Wed Mar 13 16:10:25 2013
Join Taken Time.................................. 0 days, 00 h 02 m 19 s
Attributes for Slot 0
Radio Type................................... RADIO_TYPE_80211n-2.4
Administrative State ........................ ADMIN_ENABLED
Operation State ............................. UP
Radio Role .................................. ACCESS
CellId ...................................... 0
Station Configuration
--More or (q)uit current module or to abort
Configuration ............................. AUTOMATIC
Number Of WLANs ........................... 1
Medium Occupancy Limit .................... 100
CFP Period ................................ 4
CFP MaxDuration ........................... 60
BSSID ..................................... 1c:e6:c7:04:7a:20
Operation Rate Set
1000 Kilo Bits........................... SUPPORTED
2000 Kilo Bits........................... SUPPORTED
5500 Kilo Bits........................... SUPPORTED
11000 Kilo Bits.......................... MANDATORY
MCS Set
MCS 0.................................... DISABLED
MCS 1.................................... DISABLED
MCS 2.................................... SUPPORTED
MCS 3.................................... DISABLED
MCS 4.................................... DISABLED
MCS 5.................................... DISABLED
MCS 6.................................... DISABLED
MCS 7.................................... DISABLED
MCS 8.................................... DISABLED
MCS 9.................................... DISABLED
MCS 10................................... DISABLED
--More or (q)uit current module or to abort
MCS 11................................... DISABLED
MCS 12................................... DISABLED
MCS 13................................... DISABLED
MCS 14................................... DISABLED
MCS 15................................... DISABLED
MCS 16................................... DISABLED
MCS 17................................... DISABLED
MCS 18................................... DISABLED
MCS 19................................... DISABLED
MCS 20................................... DISABLED
MCS 21................................... DISABLED
MCS 22................................... DISABLED
MCS 23................................... DISABLED
Beacon Period ............................. 100
Fragmentation Threshold ................... 2346
Multi Domain Capability Implemented ....... TRUE
Multi Domain Capability Enabled ........... TRUE
Country String ............................ SA
Multi Domain Capability
Configuration ............................. AUTOMATIC
First Chan Num ............................ 1
Number Of Channels ........................ 13
--More or (q)uit current module or to abort
MAC Operation Parameters
Configuration ............................. AUTOMATIC
Fragmentation Threshold ................... 2346
Packet Retry Limit ........................ 64
Tx Power
Num Of Supported Power Levels ............. 8
Tx Power Level 1 .......................... 20 dBm
Tx Power Level 2 .......................... 17 dBm
Tx Power Level 3 .......................... 14 dBm
Tx Power Level 4 .......................... 11 dBm
Tx Power Level 5 .......................... 8 dBm
Tx Power Level 6 .......................... 5 dBm
Tx Power Level 7 .......................... 2 dBm
Tx Power Level 8 .......................... -1 dBm
Tx Power Configuration .................... AUTOMATIC
Current Tx Power Level .................... 3
Phy DSSS parameters
Configuration ............................. AUTOMATIC
Current Channel ........................... 6
Extension Channel ......................... NONE
--More or (q)uit current module or to abort
Channel Width.............................. 20 Mhz
Allowed Channel List....................... 1,2,3,4,5,6,7,8,9,10,11,12,
......................................... 13
Current CCA Mode .......................... 0
ED Threshold .............................. -50
Legacy Tx Beamforming Configuration ....... CUSTOMIZED
Legacy Tx Beamforming ..................... ENABLED
Antenna Type............................... EXTERNAL_ANTENNA
External Antenna Gain (in .5 dBi units).... 0
Diversity.................................. DIVERSITY_ENABLED
802.11n Antennas
A....................................... ENABLED
B....................................... ENABLED
C....................................... ENABLED
Performance Profile Parameters
Configuration ............................. AUTOMATIC
Interference threshold..................... 10 %
Noise threshold............................ -70 dBm
RF utilization threshold................... 80 %
Data-rate threshold........................ 1000000 bps
Client threshold........................... 12 clients
Coverage SNR threshold..................... 12 dB
--More or (q)uit current module or to abort
Coverage exception level................... 25 %
Client minimum exception level............. 3 clients
Rogue Containment Information
Containment Count............................ 0
CleanAir Management Information
CleanAir Capable......................... No
Radio Extended Configurations
Beacon period.............................. 100 milliseconds
Beacon range............................... AUTO
Multicast buffer........................... AUTO
Multicast data-rate........................ AUTO
RX SOP threshold........................... AUTO
CCA threshold.............................. AUTO
Cisco AP Identifier.............................. 0
Cisco AP Name.................................... AP6c20.56a0.b352
Country code..................................... SA - Saudi Arabia
Regulatory Domain allowed by Country............. 802.11bg:-AE 802.11a:-E
AP Country code.................................. SA - Saudi Arabia
AP Regulatory Domain............................. -E
Switch Port Number .............................. 1
--More or (q)uit current module or to abort
MAC Address...................................... 6c:20:56:a0:b3:52
IP Address Configuration......................... DHCP
IP Address....................................... 192.168.0.111
IP NetMask....................................... 255.255.255.0
Gateway IP Addr.................................. 192.168.0.220
NAT External IP Address.......................... None
CAPWAP Path MTU.................................. 1485
Telnet State..................................... Disabled
Ssh State........................................ Disabled
Cisco AP Location................................ default location
Cisco AP Group Name.............................. default-group
Primary Cisco Switch Name........................
Primary Cisco Switch IP Address.................. Not Configured
Secondary Cisco Switch Name......................
Secondary Cisco Switch IP Address................ Not Configured
Tertiary Cisco Switch Name.......................
Tertiary Cisco Switch IP Address................. Not Configured
Administrative State ............................ ADMIN_ENABLED
Operation State ................................. REGISTERED
Mirroring Mode .................................. Disabled
AP Mode ......................................... Local
Public Safety ................................... Disabled
AP SubMode ...................................... Not Configured
--More or (q)uit current module or to abort
Remote AP Debug ................................. Disabled
Logging trap severity level ..................... informational
Logging syslog facility ......................... kern
S/W Version .................................... 7.3.101.0
Boot Version ................................... 12.4.2.4
Mini IOS Version ................................ 7.3.1.73
Stats Reporting Period .......................... 180
LED State........................................ Enabled
PoE Pre-Standard Switch.......................... Disabled
PoE Power Injector MAC Addr...................... Disabled
Power Type/Mode.................................. Power injector / Normal mode
Number Of Slots.................................. 2
AP Model......................................... AIR-LAP1262N-E-K9
AP Image......................................... C1260-K9W8-M
IOS Version...................................... 15.2(2)JA$
Reset Button..................................... Enabled
AP Serial Number................................. FCZ1642Z0A6
AP Certificate Type.............................. Manufacture Installed
AP User Mode..................................... CUSTOMIZED
AP User Name..................................... dawaa
AP Dot1x User Mode............................... Not Configured
AP Dot1x User Name............................... Not Configured
Cisco AP system logging host..................... 255.255.255.255
--More or (q)uit current module or to abort
AP Up Time....................................... 0 days, 22 h 01 m 44 s
AP LWAPP Up Time................................. 0 days, 01 h 25 m 37 s
Join Date and Time............................... Wed Mar 13 16:10:25 2013
Join Taken Time.................................. 0 days, 00 h 02 m 19 s
Attributes for Slot 1
Radio Type................................... RADIO_TYPE_80211n-5
Radio Subband................................ RADIO_SUBBAND_ALL
Administrative State ........................ ADMIN_ENABLED
Operation State ............................. UP
Radio Role .................................. ACCESS
CellId ...................................... 0
Station Configuration
Configuration ............................. AUTOMATIC
Number Of WLANs ........................... 1
Medium Occupancy Limit .................... 100
CFP Period ................................ 4
CFP MaxDuration ........................... 60
BSSID ..................................... 1c:e6:c7:04:7a:20
Operation Rate Set
6000 Kilo Bits........................... MANDATORY
--More or (q)uit current module or to abort
9000 Kilo Bits........................... SUPPORTED
12000 Kilo Bits.......................... MANDATORY
18000 Kilo Bits.......................... SUPPORTED
24000 Kilo Bits.......................... MANDATORY
36000 Kilo Bits.......................... SUPPORTED
48000 Kilo Bits.......................... SUPPORTED
54000 Kilo Bits.......................... SUPPORTED
MCS Set
MCS 0.................................... DISABLED
MCS 1.................................... DISABLED
MCS 2.................................... DISABLED
MCS 3.................................... SUPPORTED
MCS 4.................................... SUPPORTED
MCS 5.................................... SUPPORTED
MCS 6.................................... SUPPORTED
MCS 7.................................... SUPPORTED
MCS 8.................................... SUPPORTED
MCS 9.................................... SUPPORTED
MCS 10................................... SUPPORTED
MCS 11................................... SUPPORTED
MCS 12................................... SUPPORTED
MCS 13................................... SUPPORTED
MCS 14................................... SUPPORTED
--More or (q)uit current module or to abort
MCS 15................................... SUPPORTED
MCS 16................................... DISABLED
MCS 17................................... DISABLED
MCS 18................................... DISABLED
MCS 19................................... DISABLED
MCS 20................................... DISABLED
MCS 21................................... DISABLED
MCS 22................................... DISABLED
MCS 23................................... DISABLED
Beacon Period ............................. 100
Fragmentation Threshold ................... 2346
Multi Domain Capability Implemented ....... TRUE
Multi Domain Capability Enabled ........... TRUE
Country String ............................ SA
Multi Domain Capability
Configuration ............................. AUTOMATIC
First Chan Num ............................ 36
Number Of Channels ........................ 4
MAC Operation Parameters
Configuration ............................. AUTOMATIC
Fragmentation Threshold ................... 2346
--More or (q)uit current module or to abort
Packet Retry Limit ........................ 64
Tx Power
Num Of Supported Power Levels ............. 7
Tx Power Level 1 .......................... 17 dBm
Tx Power Level 2 .......................... 14 dBm
Tx Power Level 3 .......................... 11 dBm
Tx Power Level 4 .......................... 8 dBm
Tx Power Level 5 .......................... 5 dBm
Tx Power Level 6 .......................... 2 dBm
Tx Power Level 7 .......................... -1 dBm
Tx Power Configuration .................... AUTOMATIC
Current Tx Power Level .................... 1
Phy OFDM parameters
Configuration ............................. AUTOMATIC
Current Channel ........................... 36
Extension Channel ......................... NONE
Channel Width.............................. 20 Mhz
Allowed Channel List....................... 36,40,44,48,52,56,60,64,100,
......................................... 104,108,112,116,132,136,140
TI Threshold .............................. -50
Legacy Tx Beamforming Configuration ....... CUSTOMIZED
--More or (q)uit current module or to abort
Legacy Tx Beamforming ..................... ENABLED
Antenna Type............................... EXTERNAL_ANTENNA
External Antenna Gain (in .5 dBi units).... 0
Diversity.................................. DIVERSITY_ENABLED
802.11n Antennas
A....................................... ENABLED
B....................................... ENABLED
C....................................... ENABLED
Performance Profile Parameters
Configuration ............................. AUTOMATIC
Interference threshold..................... 10 %
Noise threshold............................ -70 dBm
RF utilization threshold................... 80 %
Data-rate threshold........................ 1000000 bps
Client threshold........................... 12 clients
Coverage SNR threshold..................... 16 dB
Coverage exception level................... 25 %
Client minimum exception level............. 3 clients
Rogue Containment Information
Containment Count............................ 0
CleanAir Management Information
--More or (q)uit current module or to abort
CleanAir Capable......................... No
Radio Extended Configurations
Beacon period.............................. 100 milliseconds
Beacon range............................... AUTO
Multicast buffer........................... AUTO
Multicast data-rate........................ AUTO
RX SOP threshold........................... AUTO
CCA threshold.............................. AUTO
Press Enter to continue or to abort
Cisco AP Identifier.............................. 1
Cisco AP Name.................................... AP6c20.5666.e34a
Country code..................................... SA - Saudi Arabia
Regulatory Domain allowed by Country............. 802.11bg:-AE 802.11a:-E
AP Country code.................................. SA - Saudi Arabia
AP Regulatory Domain............................. -E
Switch Port Number .............................. 1
MAC Address...................................... 6c:20:56:66:e3:4a
IP Address Configuration......................... DHCP
IP Address....................................... 192.168.0.39
IP NetMask....................................... 255.255.255.0
Gateway IP Addr.................................. 192.168.0.220
NAT External IP Address.......................... None
CAPWAP Path MTU.................................. 1485
Telnet State..................................... Disabled
Ssh State........................................ Disabled
Cisco AP Location................................ default location
Cisco AP Group Name.............................. default-group
Primary Cisco Switch Name........................
Primary Cisco Switch IP Address.................. Not Configured
Secondary Cisco Switch Name......................
Secondary Cisco Switch IP Address................ Not Configured
--More or (q)uit current module or to abort
Tertiary Cisco Switch Name.......................
Tertiary Cisco Switch IP Address................. Not Configured
Administrative State ............................ ADMIN_ENABLED
Operation State ................................. REGISTERED
Mirroring Mode .................................. Disabled
AP Mode ......................................... Local
Public Safety ................................... Disabled
AP SubMode ...................................... Not Configured
Remote AP Debug ................................. Disabled
Logging trap severity level ..................... informational
Logging syslog facility ......................... kern
S/W Version .................................... 7.3.101.0
Boot Version ................................... 12.4.2.4
Mini IOS Version ................................ 7.3.1.73
Stats Reporting Period .......................... 180
LED State........................................ Enabled
PoE Pre-Standard Switch.......................... Disabled
PoE Power Injector MAC Addr...................... Disabled
Power Type/Mode.................................. Power injector / Normal mode
Number Of Slots.................................. 2
AP Model......................................... AIR-LAP1262N-E-K9
AP Image......................................... C1260-K9W8-M
IOS Version...................................... 15.2(2)JA$
--More or (q)uit current module or to abort
Reset Button..................................... Enabled
AP Serial Number................................. FCZ1642Z09V
AP Certificate Type.............................. Manufacture Installed
AP User Mode..................................... AUTOMATIC
AP User Name..................................... Not Configured
AP Dot1x User Mode............................... Not Configured
AP Dot1x User Name............................... Not Configured
Cisco AP system logging host..................... 255.255.255.255
AP Up Time....................................... 0 days, 22 h 03 m 17 s
AP LWAPP Up Time................................. 0 days, 01 h 28 m 23 s
Join Date and Time............................... Wed Mar 13 16:10:26 2013
Join Taken Time.................................. 0 days, 00 h 02 m 04 s
Attributes for Slot 0
Radio Type................................... RADIO_TYPE_80211n-2.4
Administrative State ........................ ADMIN_ENABLED
Operation State ............................. UP
Radio Role .................................. ACCESS
CellId ...................................... 0
Station Configuration
Configuration ............................. AUTOMATIC
--More or (q)uit current module or to abort
Number Of WLANs ........................... 1
Medium Occupancy Limit .................... 100
CFP Period ................................ 4
CFP MaxDuration ........................... 60
BSSID ..................................... 54:78:1a:f2:51:c0
Operation Rate Set
1000 Kilo Bits........................... SUPPORTED
2000 Kilo Bits........................... SUPPORTED
5500 Kilo Bits........................... SUPPORTED
11000 Kilo Bits.......................... MANDATORY
MCS Set
MCS 0.................................... DISABLED
MCS 1.................................... DISABLED
MCS 2.................................... SUPPORTED
MCS 3.................................... DISABLED
MCS 4.................................... DISABLED
MCS 5.................................... DISABLED
MCS 6.................................... DISABLED
MCS 7.................................... DISABLED
MCS 8.................................... DISABLED
MCS 9.................................... DISABLED
MCS 10................................... DISABLED
MCS 11................................... DISABLED
--More or (q)uit current module or to abort
MCS 12................................... DISABLED
MCS 13................................... DISABLED
MCS 14................................... DISABLED
MCS 15................................... DISABLED
MCS 16................................... DISABLED
MCS 17................................... DISABLED
MCS 18................................... DISABLED
MCS 19................................... DISABLED
MCS 20................................... DISABLED
MCS 21................................... DISABLED
MCS 22................................... DISABLED
MCS 23................................... DISABLED
Beacon Period ............................. 100
Fragmentation Threshold ................... 2346
Multi Domain Capability Implemented ....... TRUE
Multi Domain Capability Enabled ........... TRUE
Country String ............................ SA
Multi Domain Capability
Configuration ............................. AUTOMATIC
First Chan Num ............................ 1
Number Of Channels ........................ 13
--More or (q)uit current module or to abort
MAC Operation Parameters
Configuration ............................. AUTOMATIC
Fragmentation Threshold ................... 2346
Packet Retry Limit ........................ 64
Tx Power
Num Of Supported Power Levels ............. 8
Tx Power Level 1 .......................... 20 dBm
Tx Power Level 2 .......................... 17 dBm
Tx Power Level 3 .......................... 14 dBm
Tx Power Level 4 .......................... 11 dBm
Tx Power Level 5 .......................... 8 dBm
Tx Power Level 6 .......................... 5 dBm
Tx Power Level 7 .......................... 2 dBm
Tx Power Level 8 .......................... -1 dBm
Tx Power Configuration .................... AUTOMATIC
Current Tx Power Level .................... 2
Phy DSSS parameters
Configuration ............................. AUTOMATIC
Current Channel ........................... 1
Extension Channel ......................... NONE
Channel Width.............................. 20 Mhz
--More or (q)uit current module or to abort
Allowed Channel List....................... 1,2,3,4,5,6,7,8,9,10,11,12,
......................................... 13
Current CCA Mode .......................... 0
ED Threshold .............................. -50
Legacy Tx Beamforming Configuration ....... CUSTOMIZED
Legacy Tx Beamforming ..................... ENABLED
Antenna Type............................... EXTERNAL_ANTENNA
External Antenna Gain (in .5 dBi units).... 0
Diversity.................................. DIVERSITY_ENABLED
802.11n Antennas
A....................................... ENABLED
B....................................... ENABLED
C....................................... ENABLED
Performance Profile Parameters
Configuration ............................. AUTOMATIC
Interference threshold..................... 10 %
Noise threshold............................ -70 dBm
RF utilization threshold................... 80 %
Data-rate threshold........................ 1000000 bps
Client threshold........................... 12 clients
Coverage SNR threshold..................... 12 dB
Coverage exception level................... 25 %
--More or (q)uit current module or to abort
Client minimum exception level............. 3 clients
Rogue Containment Information
Containment Count............................ 0
CleanAir Management Information
CleanAir Capable......................... No
Radio Extended Configurations
Beacon period.............................. 100 milliseconds
Beacon range............................... AUTO
Multicast buffer........................... AUTO
Multicast data-rate........................ AUTO
RX SOP threshold........................... AUTO
CCA threshold.............................. AUTO
Cisco AP Identifier.............................. 1
Cisco AP Name.................................... AP6c20.5666.e34a
Country code..................................... SA - Saudi Arabia
Regulatory Domain allowed by Country............. 802.11bg:-AE 802.11a:-E
AP Country code.................................. SA - Saudi Arabia
AP Regulatory Domain............................. -E
Switch Port Number .............................. 1
MAC Address...................................... 6c:20:56:66:e3:4a
--More or (q)uit current module or to abort
IP Address Configuration......................... DHCP
IP Address....................................... 192.168.0.39
IP NetMask....................................... 255.255.255.0
Gateway IP Addr.................................. 192.168.0.220
NAT External IP Address.......................... None
CAPWAP Path MTU.................................. 1485
Telnet State..................................... Disabled
Ssh State........................................ Disabled
Cisco AP Location................................ default location
Cisco AP Group Name.............................. default-group
Primary Cisco Switch Name........................
Primary Cisco Switch IP Address.................. Not Configured
Secondary Cisco Switch Name......................
Secondary Cisco Switch IP Address................ Not Configured
Tertiary Cisco Switch Name.......................
Tertiary Cisco Switch IP Address................. Not Configured
Administrative State ............................ ADMIN_ENABLED
Operation State ................................. REGISTERED
Mirroring Mode .................................. Disabled
AP Mode ......................................... Local
Public Safety ................................... Disabled
AP SubMode ...................................... Not Configured
Remote AP Debug ................................. Disabled
--More or (q)uit current module or to abort
Logging trap severity level ..................... informational
Logging syslog facility ......................... kern
S/W Version .................................... 7.3.101.0
Boot Version ................................... 12.4.2.4
Mini IOS Version ................................ 7.3.1.73
Stats Reporting Period .......................... 180
LED State........................................ Enabled
PoE Pre-Standard Switch.......................... Disabled
PoE Power Injector MAC Addr...................... Disabled
Power Type/Mode.................................. Power injector / Normal mode
Number Of Slots.................................. 2
AP Model......................................... AIR-LAP1262N-E-K9
AP Image......................................... C1260-K9W8-M
IOS Version...................................... 15.2(2)JA$
Reset Button..................................... Enabled
AP Serial Number................................. FCZ1642Z09V
AP Certificate Type.............................. Manufacture Installed
AP User Mode..................................... AUTOMATIC
AP User Name..................................... Not Configured
AP Dot1x User Mode............................... Not Configured
AP Dot1x User Name............................... Not Configured
Cisco AP system logging host..................... 255.255.255.255
AP Up Time....................................... 0 days, 22 h 03 m 17 s
--More or (q)uit current module or to abort
AP LWAPP Up Time................................. 0 days, 01 h 28 m 23 s
Join Date and Time............................... Wed Mar 13 16:10:26 2013
Join Taken Time.................................. 0 days, 00 h 02 m 04 s
Attributes for Slot 1
Radio Type................................... RADIO_TYPE_80211n-5
Radio Subband................................ RADIO_SUBBAND_ALL
Administrative State ........................ ADMIN_ENABLED
Operation State ............................. UP
Radio Role .................................. ACCESS
CellId ...................................... 0
Station Configuration
Configuration ............................. AUTOMATIC
Number Of WLANs ........................... 1
Medium Occupancy Limit .................... 100
CFP Period ................................ 4
CFP MaxDuration ........................... 60
BSSID ..................................... 54:78:1a:f2:51:c0
Operation Rate Set
6000 Kilo Bits........................... MANDATORY
9000 Kilo Bits........................... SUPPORTED
--More or (q)uit current module or to abort
12000 Kilo Bits.......................... MANDATORY
18000 Kilo Bits.......................... SUPPORTED
24000 Kilo Bits.......................... MANDATORY
36000 Kilo Bits.......................... SUPPORTED
48000 Kilo Bits.......................... SUPPORTED
54000 Kilo Bits.......................... SUPPORTED
MCS Set
MCS 0.................................... DISABLED
MCS 1.................................... DISABLED
MCS 2.................................... DISABLED
MCS 3.................................... SUPPORTED
MCS 4.................................... SUPPORTED
MCS 5.................................... SUPPORTED
MCS 6.................................... SUPPORTED
MCS 7.................................... SUPPORTED
MCS 8.................................... SUPPORTED
MCS 9.................................... SUPPORTED
MCS 10................................... SUPPORTED
MCS 11................................... SUPPORTED
MCS 12................................... SUPPORTED
MCS 13................................... SUPPORTED
MCS 14................................... SUPPORTED
MCS 15................................... SUPPORTED
--More or (q)uit current module or to abort
MCS 16................................... DISABLED
MCS 17................................... DISABLED
MCS 18................................... DISABLED
MCS 19................................... DISABLED
MCS 20................................... DISABLED
MCS 21................................... DISABLED
MCS 22................................... DISABLED
MCS 23................................... DISABLED
Beacon Period ............................. 100
Fragmentation Threshold ................... 2346
Multi Domain Capability Implemented ....... TRUE
Multi Domain Capability Enabled ........... TRUE
Country String ............................ SA
Multi Domain Capability
Configuration ............................. AUTOMATIC
First Chan Num ............................ 36
Number Of Channels ........................ 4
MAC Operation Parameters
Configuration ............................. AUTOMATIC
Fragmentation Threshold ................... 2346
Packet Retry Limit ........................ 64
--More or (q)uit current module or to abort
Tx Power
Num Of Supported Power Levels ............. 7
Tx Power Level 1 .......................... 17 dBm
Tx Power Level 2 .......................... 14 dBm
Tx Power Level 3 .......................... 11 dBm
Tx Power Level 4 .......................... 8 dBm
Tx Power Level 5 .......................... 5 dBm
Tx Power Level 6 .......................... 2 dBm
Tx Power Level 7 .......................... -1 dBm
Tx Power Configuration .................... AUTOMATIC
Current Tx Power Level .................... 1
Phy OFDM parameters
Configuration ............................. AUTOMATIC
Current Channel ........................... 64
Extension Channel ......................... NONE
Channel Width.............................. 20 Mhz
Allowed Channel List....................... 36,40,44,48,52,56,60,64,100,
......................................... 104,108,112,116,132,136,140
TI Threshold .............................. -50
Legacy Tx Beamforming Configuration ....... CUSTOMIZED
Legacy Tx Beamforming ..................... ENABLED
--More or (q)uit current module or to abort
Antenna Type............................... EXTERNAL_ANTENNA
External Antenna Gain (in .5 dBi units).... 0
Diversity.................................. DIVERSITY_ENABLED
802.11n Antennas
A....................................... ENABLED
B....................................... ENABLED
C....................................... ENABLED
Performance Profile Parameters
Configuration ............................. AUTOMATIC
Interference threshold..................... 10 %
Noise threshold............................ -70 dBm
RF utilization threshold................... 80 %
Data-rate threshold........................ 1000000 bps
Client threshold........................... 12 clients
Coverage SNR threshold..................... 16 dB
Coverage exception level................... 25 %
Client minimum exception level............. 3 clients
Rogue Containment Information
Containment Count............................ 0
CleanAir Management Information
CleanAir Capable......................... No
--More or (q)uit current module or to abort
Radio Extended Configurations
Beacon period.............................. 100 milliseconds
Beacon range............................... AUTO
Multicast buffer........................... AUTO
Multicast data-rate........................ AUTO
RX SOP threshold........................... AUTO
CCA threshold.............................. AUTO
Press Enter to continue or to abort
Cisco AP Identifier.............................. 2
Cisco AP Name.................................... AP6c20.56a0.b341
Country code..................................... SA - Saudi Arabia
Regulatory Domain allowed by Country............. 802.11bg:-AE 802.11a:-E
AP Country code.................................. SA - Saudi Arabia
AP Regulatory Domain............................. -E
Switch Port Number .............................. 1
MAC Address...................................... 6c:20:56:a0:b3:41
IP Address Configuration......................... DHCP
IP Address....................................... 192.168.0.120
IP NetMask....................................... 255.255.255.0
Gateway IP Addr.................................. 192.168.0.220
NAT External IP Address.......................... None
CAPWAP Path MTU.................................. 1485
Telnet State..................................... Disabled
Ssh State........................................ Disabled
Cisco AP Location................................ default location
Cisco AP Group Name.............................. default-group
Primary Cisco Switch Name........................
Primary Cisco Switch IP Address.................. Not Configured
Secondary Cisco Switch Name......................
Secondary Cisco Switch IP Address................ Not Configured
--More or (q)uit current module or to abort
Tertiary Cisco Switch Name.......................
Tertiary Cisco Switch IP Address................. Not Configured
Administrative State ............................ ADMIN_ENABLED
Operation State ................................. REGISTERED
Mirroring Mode .................................. Disabled
AP Mode ......................................... Local
Public Safety ................................... Disabled
AP SubMode ...................................... Not Configured
Remote AP Debug ................................. Disabled
Logging trap severity level ..................... informational
Logging syslog facility ......................... kern
S/W Version .................................... 7.3.101.0
Boot Version ................................... 12.4.2.4
Mini IOS Version ................................ 7.3.1.73
Stats Reporting Period .......................... 180
LED State........................................ Enabled
PoE Pre-Standard Switch.......................... Disabled
PoE Power Injector MAC Addr...................... Disabled
Power Type/Mode.................................. Power injector / Normal mode
Number Of Slots.................................. 2
AP Model......................................... AIR-LAP1262N-E-K9
AP Image......................................... C1260-K9W8-M
IOS Version...................................... 15.2(2)JA$
--More or (q)uit current module or to abort
Reset Button..................................... Enabled
AP Serial Number................................. FCZ1642Z09Y
AP Certificate Type.............................. Manufacture Installed
AP User Mode..................................... CUSTOMIZED
AP User Name..................................... dawaa
AP Dot1x User Mode............................... Not Configured
AP Dot1x User Name............................... Not Configured
Cisco AP system logging host..................... 255.255.255.255
AP Up Time....................................... 0 days, 22 h 07 m 08 s
AP LWAPP Up Time................................. 0 days, 01 h 31 m 05 s
Join Date and Time............................... Wed Mar 13 16:10:26 2013
Join Taken Time.................................. 0 days, 00 h 02 m 19 s
Attributes for Slot 0
Radio Type................................... RADIO_TYPE_80211n-2.4
Administrative State ........................ ADMIN_ENABLED
Operation State ............................. UP
Radio Role .................................. ACCESS
CellId ...................................... 0
Station Configuration
Configuration ............................. AUTOMATIC
--More or (q)uit current module or to abort
Number Of WLANs ........................... 1
Medium Occupancy Limit .................... 100
CFP Period ................................ 4
CFP MaxDuration ........................... 60
BSSID ..................................... 1c:e6:c7:04:81:f0
Operation Rate Set
1000 Kilo Bits........................... SUPPORTED
2000 Kilo Bits........................... SUPPORTED
5500 Kilo Bits........................... SUPPORTED
11000 Kilo Bits.......................... MANDATORY
MCS Set
MCS 0.................................... DISABLED
MCS 1.................................... DISABLED
MCS 2.................................... SUPPORTED
MCS 3.................................... DISABLED
MCS 4.................................... DISABLED
MCS 5.................................... DISABLED
MCS 6.................................... DISABLED
MCS 7.................................... DISABLED
MCS 8.................................... DISABLED
MCS 9.................................... DISABLED
MCS 10................................... DISABLED
MCS 11................................... DISABLED
--More or (q)uit current module or to abort
MCS 12................................... DISABLED
MCS 13................................... DISABLED
MCS 14................................... DISABLED
MCS 15................................... DISABLED
MCS 16................................... DISABLED
MCS 17................................... DISABLED
MCS 18................................... DISABLED
MCS 19................................... DISABLED
MCS 20................................... DISABLED
MCS 21................................... DISABLED
MCS 22................................... DISABLED
MCS 23................................... DISABLED
Beacon Period ............................. 100
Fragmentation Threshold ................... 2346
Multi Domain Capability Implemented ....... TRUE
Multi Domain Capability Enabled ........... TRUE
Country String .............. -
2500 series support mobility groups?
Do you know if the new 2500 series controller supports things like mobility groups? Could I use 2 of these and do inter-controller roaming.
Also do you know if this would work with a 2106 controller and a 2505 controller or are they 2 completely independent controllers only knowing about their own APs??Hi smailmilak,
no mobility and roaming is not the same. You need for roaming between controllers a mobility configuration.
If you have only one 2500 WLC and 25 or more or less AP roaming between the AP on the one WLC will work well.
This calls Intra-Controller roaming
If you have 2 or more WLCs you need a proper mobility config for roaming between APs located on differen WLC.
This Calls Inter-Controller roaming.
More informations are here:
http://www.cisco.com/en/US/docs/wireless/controller/7.0/configuration/guide/c70mobil.html -
Identity Services Engine (ISE) support for the WLC 2500
Is the ISE going to support the 2500 series Wireless LAN Controller WLC? If yes in what release and appriximately when is that due to be released?
Your question is disturbing. ISE is (amongst other things) a radius server. WLC 2500 can use radius servers for authentication. So it's supported.
Any device doing radius is supported with ISE ...
Now you are maybe referring to a particular feature in ISE ? -
Cisco WLC 2500 - 802.1x with Vasco Radius SMS OTP
Hello folks,
I have what seems to be a complex implementation with many things that need to be done on a customers network and I wanted to be pointed in the right direction.
The current scenario is such, the customer has a Cisco WLC 2500 device that has 3 access points(these are in the same AP group) connected to it. There is one SSID that I will call PRODUCTION here that some domain users use to connect to the local network. The customer has requested to have a GUEST SSID added to the WLC where guest users will connect to and recieve a SMS OTP for authentication.
Correct me if I am wrong, but I will obviously need to segment the SSIDs to have them running on different subnets to ensure that guest users do not have access to the production network once they authenticate. In order to do this I will need to configure Dynamic VLAN assignment for the Cisco WLC and connect it to a 802.1x port on the switch.
Now what is not clear is I am not interested in authenticating the users that connect via "Production SSID" and want to bypass authentication for those users and have them assigned to the default vlan (or maybe perhaps have them authenticate via LDAP on the AD), however I want to force the "GUEST" SSID users to authenticate so that they may recieve an SMS OTP (reason for this is to force guests to register their phone numbers to use the internet so that Illegal activity may be tracked).
1)So would it be possible to bypass authentication(or authenticate them via LDAP) for the PRODUCTION SSID as only domain users would know the SSID password to log on and have them by default assigned to the production subnet (default vlan) but force the GUEST SSID users to another VLAN via 802.1x sms otp?
2)*Important* Another issue that is not clear is will I be able to directly configure AAA Radius settings on the Cisco WLC to directly authenticate with the VASCO Radius OTP and recieve a challenge-response(required for OTP) during authentication? As I have seen from Ciscos Dynamic VLAN assignment docuementation (http://www.cisco.com/en/US/tech/tk722/tk809/technologies_configuration_example09186a008076317c.shtml) additional IETF Radius Perimeters are used such as Tunnel-Private-Group-ID etc are used which I can't seem to configure on the Vasco.
I do beileve this is a great project in helping me understand the INs and OUTs of CISCO WLC as well as Wireless NAC, If anyone could enlighten me and point me in the right direction I would be forever in debt. Much appreciated.
Best Regards
Sinan Barghouthi - JNCIA-FWV , JNCIA-IDP , CCA-NS , TCSM-8.0On your WLAN you can enable AES and TKIP. Just know that some clients mau have issue when they see both TKIP and AES. Ive had pretty good success with this in the past. Dont forget, you also need to enable WMM allowed to get N rates.
But you will need to configure AES on the client as well to support N rates.
"Satisfaction does not come from knowing the solution, it comes from knowing why." - Rosalind Franklin
"I'm in a serious relationship with my Wi-Fi. You could say we have a connection." -
Error in Cisco 2500 series Wireless Controller
I have this error in Cisco 2500 series Wireless Controller
The AP type Cisco AIR-CAP35021-A-K9
I cann't connect the client to AP when i try to connect i get this error on Cisco 2500 series Wireless Controller But the AP get ip .
Please can any on help me .
Client Excluded: MACAddress:Base Radio MAC : Slot: 0 User Name: unknown Ip Address: unknown Reason:802.11 Association failed repeatedly. ReasonCode:Duplicate posts.
Go here: http://supportforums.cisco.com/discussion/12142556/cisco-2500-series-wireless-controller -
hello
i have a question about a cisco wlc 2500.
when you configure a interface on the controller, you can set a ip address
mask en DHCP server address but also you can set the interface as a AP-Manager
why is this?
thanksOn the old WLC models like 2100, 2006,4400 we had to configure the management interface for managing the WLC and the AP manager so that the APs could create the LWAPP or CAPWAP tunnel to the WLC.
On the new model of WLCs like the 2500,5508 the AP manager interface is not required, the management interface if it has the check for dynamic interface it will work at the same time as the AP manager interface.
Here is the link where you can check on how to deploy the 2504 WLC and the different setups to use with several AP managers.
http://www.cisco.com/en/US/products/ps11630/products_tech_note09186a0080b8450c.shtml -
WLC 2100 series Guest LAN not found
Hi there
I am unable to configure Guest LAN as in this link
http://www.cisco.com/en/US/tech/tk722/tk809/technologies_configuration_example09186a00808ed026.shtml
because my Cisco WLC 2112 version 7.0.240.0 does not have the option for Guest LAN. Is Guest LAN supported for WLC 2100 series? Any workarounds or suggestions?
Thanks for your help
DIegoDiego,
Wired guest access is not supported on WLC2106.
Reference:
http://www.cisco.com/en/US/tech/tk722/tk809/technologies_configuration_example09186a00808ed026.shtml#configs
consider using a WISM, WLC4400, 3750 integrated WLC or a WLC5500 -
WLC 4400 series OID for Current Clients
Can someone advise what is the OID for the number of current clients for the WLC 4400 series appliance.
Thanks.Based on the results of your walk, I would say it's reports all of the instances on that particular controller...and I say this because only one instance is reported. I would think that if you have multiple WLANS on that WLC, you would get multiple instances reported back, so, (maybe, like you) I'm confused by the description in the MIB object where it states:
"No of Mobile Stations currently associated with the WLAN."
which to me looks like "the WLAN" is used in the singular.
At this point, I think the best thing to do would be to open a TAC case with all of this info, and we can get with our developers for confirmation.
Hope this has been somewhat helpful, and please rate these posts.
Thanks,
-Joe -
Problèmes d'ajout de licences sur un controller WLC 2500
Bonjour,
Je possède un Cisco WLC 2500 controller pour mes bornes Wifi.
Sur ce controller j'ai déjà un pack de 25 licences d'installées.
Récemment j'ai acheté un nouveau pack de licence et il met impossible de l'ajouter correctement.
j’effectue la procédure suivante :
Je clique dans l'onglet "management" puis sur "software activation"
Je clique sur "commandes"
Je sélectionne "install licences"
ce que j'obtiens
ensuite je reboot le controller, mais les licences ne sont pas présente dans la liste.
Avez-vous une idée ?
Merci d'avanceGREP peut servir à deux choses : un enrichissement automatique via les styles GREP ou un rechercher-remplacer. Les styles GREP ne font qu'enrichir du texte existant mais n'ont pas pour fonction d'ajouter du texte. Pour ce que tu cherches à faire (un ajout), la syntaxe proposée dans le livre doit donc être utilisée dans la boîte de dialogue « rechercher-remplacer ».
-
Hi,
I have WLC 2500 with firmware 7.4.121.0. Problem is with multicasting (or media streaming). One big boss wants his camera communicate with tablet, ant this communication requires multicast.
In MONITOR-> Multicast I can devices trying to communicate but nothing happens. I found some guides how to configure multicast for video or voice, but I have no luck with them.
Perhaps someone had luck with such configuration?
Thanks.Hi
See whether below helps (these are with wlc 7.0 code, but I think not much differences in 7.4 compare to 7.0). Refer specific configuration guide for exact syntax
http://mrncciew.com/2012/12/24/understanding-videostream-feature/
http://mrncciew.com/2012/11/17/configuring-multicast-on-wlc/
Make sure your wired network also support multicast.
HTH
Rasika
*** Pls rate all useful responses ****
Maybe you are looking for
-
Config collection fails occasionally in LMS 4.2
Hello, In recently installed LMS 4.2 archive collection is failing from time to time for random number of devices with error: "Execution Result: CM00139 Could not archive config Cause: Action: Verify that device is managed and credentials are
-
Hi ! I am developing an application remotely executable. The server part I have developed in the Java EE 7 platform, using Glassfish as application server and EJB for the business logic I thought the client side with Java FX develop What is the best
-
When I get an attachment in my email .xls I cannot open it on my email nor with numbers. .xlsx is to a problem. How do I resolve this?
-
Need to decommission a Windows 2003 server....
I have a Windows 2003 DC with all the FSMO roles. It was the first DC of the domain I also have 3 other DCs that are Windows 2008 R2. All of the DCs are global catalogs. DHCP Server is running on the Windows 2003 DC. All of the DCs run DNS Ser
-
WSUS Role on Server 2012 R2 fails - SQL Server Error "Schema Verification Failed SUSDB"
Server is Windows Server 2012R2 After installing the WSUS role with WID, when running the post installation task it installs the SUSDB in single user mode, runs all its scripts but then when it tries to set it it MULTI mode it fails with the error: S