WLC 2504 don't work with mode trunking dot1Q with 3560cg and 2960cg?

Hi
I have a proble with the 3560cg and 2960cg, when i configure the port with "switchport trunk encapsulation doi1q " and "switchport mode trunk" on the interface for the connection with the WLC2504, don't have connection.
I configure others WLC and others switch catalyst (2960, 3550, etc) with the same configuration and this connection work very well.
this is the date from the terminals:
Model SW Version SW Image
WS-C2960CG-8TC-L 12.2(55)EX2 C2960c405ex-UNIVERSALK9-M
Model SW Version SW Image
WS-C3560CG-8TC-S 12.2(55)EX2 C3560c405ex-UNIVERSALK9-M
WLC 2504 IOS-> 7.3.
I don't know what its hapend, or if i need use another command for the 3560cg and 2960cg
Regards

Hi scot
in my case, i configure the 3560 with the vlan 1 for administration and the vlan 100 and 200 for my clients (i use the 2 vlans with 2 wlans from the wlc) and i know that the port must be Trunk, my management interface its taggin with the vlan 1 for the administration and the dynamic interfaces with the respective vlan.
when i configure the 3560 and 2960 i use these command (switchport mode trunk) and i loose the connection with the wlc (i use the same comand with other switch and work very well), the wlc loose the conection with the net.
i dont know the reason for this failure, and i know if the wlc have management interface untugged, only work with this vlan (vlan native or vlan access) and don't work with the others vlans for the wlans.
I wish to know if the IOS or if exist another configuration for the 3560 and 2960 works with the WLC correctly or its problem of the IOS
Thaks for the help
Regards

Similar Messages

My iPod nano don't works. I take shower with it. What do i do?

my iPod nano don't works. I take shower with it. What do i do?

iPod nano's are not waterproof. It's almost certainly dead. Time for a trip to the Apple store to buy a replacement. Try and keep the new one dry!

Color don't work well in Mac book pro 13" and monitor flash sometimes? Please help me!

Color don't work well in Mac book pro 13" and monitor flash sometimes? Please help me!

Please describe the problem in as much relevant detail as possible. The "etrecheck" fad hasn't made that step any less necessary. The usual results of posting etrecheck output on this site without a full description of the problem are very poor.
The many "failed" warnings that etrecheck sometimes spews mean nothing. Those warnings are not a reason to reinstall the OS, or to do anything else at all. They should be ignored.
The better your description of the problem, the better the chance of a solution.
For example, if the computer is slow, which specific actions are slow? Is it slow all the time, or only sometimes? What changes did you make, if any, just before it became slow? Have you seen any alerts or error messages? Have you done anything to try to fix it? Most importantly, do you have a current backup of all data? If the answer to the last question is "no," back up now. Ask if you need guidance. Do nothing else until you have a backup.

TS1702 Since updating to iOS 6.0, my Facebook and instagram both don't work. Any ideas as to why and how it can be fixed ASAP?

Since updating to iOS 6.0, my Facebook and instagram both don't work. Any ideas as to why and how it can be fixed ASAP?

Since updating to iOS 6.0, my Facebook and instagram both don't work. Any ideas as to why and how it can be fixed ASAP?

WLC 2504 Airplay not working over wireless

Currently we are trying to use Airplay within our network and we're having really wierd issues.
First, we have 2 subnets: 192.168.x.x and 10.x.x.x
We have our wired Apple TV's on 192.168.x.x. and our wireless Apple TV's on 10.x.x.x
We also have wired computers on both networks. But all of our wireless clients are on 10.x.x.x.
So:
-Wired computers (in both subnets) can get to the wired Apple TV's.
-Wireless computer cannot get to any Apple TV's.
-Nothing can get to the wireless Apple TV's.
What I've done from other forums:
-I've enabled Global Multicast and set a multicast adddress
-I've tried it with and without IGMP snooping
-Enabled multicast routing on the switches that the Access Points are connected to
-Using Bonjour Browser, I don't see any AirTunes devices when I'm connected Wirelessly
Any help would be greatly appreciated

I've done that, but nothing has changed. But looking at the profiles:
Profile Name                                   default-mdns-profile
Profile Id                                         1
Service Count                                  7
No. of Interfaces Attached                0
No. of Interface Groups Attached      0
No. of Wlans Attached                     1
I can't find where I can set in the WLAN where the profile is applied. We only have 1 interface connected to the controller (interface 1 which is the management interface). I'm assuming that it only needs to be applied to the WLAN, but I'm wondering if this is set to the right WLAN. Where can I find this?

Hyperlinks don't work in frames where you have videos, and....

Did you notice that if you put a hyperlink in a frame where you already have a video, after you export in quicktime your presentation, the hyperlink won't work no more?
And did u notice that if you use an hyperlink to a frame that is not the follower one, this will blast off any transition?
And did you notice this happens in Keynote 08 AND Keynote 09?
AND AM I THE ONLY ONE THAT NOTICED THIS AND IS SICK TO PAY FOR A SOFTWARE THAT "just DON'T work" ??

How bout adding the URL after the vid? That works for me; remember a connection to a URL drops you out of Keynote & Sets up Safari, so you're completely out of the app & have to get back in through the dock. I'm uncertain what you mean about the transition blast; cold you give more detail?
In fairness, all apps fail to do something or other, and this does not mean they don't work. If you want to pay big bucks & fight with PP, fine, but I'll stick to the more versatile and easy-to-use KN.

Keys don't work; 4 5 6 + up/down arrow and right shift

Some keys stopped working the num keypad 4 5 6 + 9 (the whole row), the up and down arrow and the right shift. All other keys work
I saw a post with the exact same problem, however with no solution, which makes me wonder if it's a configuration thing?
I went into the keyboard shortcut settings and hit restore defaults, the computer has been restarted many times. I looked at the international settings (input tab) and noticed that "character palette" with unicode script is selected along with u.s. keyboard roman script. I assume this is correct ( I unchecked character pallett" just to see what would happen, no help, so I checked it back on.
please help.....

Dear Daddy Paycheck
Your comment "a cheap" usb keyboard would work made me realize that I don't need to go to apple and purchase a new keyboard just to troubleshoot
I just figured that it had to be an "apple" keyboard, silly me!
so I just went and got my old compaq keyboard from my old computer in the trash pile. heck, a few quick requests to push the z and ? keys and it works great.
the apple now has tears on it, cause of the compaq keyboard, but too bad, it shouldn't have broke!!!! this compaq keyboard is 9 years old and still works great, why would I go spend $30 on another apple keyboard that only lasts 1 year??!
g5 Mac OS X (10.4.4)

My headphones don't work. I have tried other ones and still not working

My headphones stopped working. I have tried other headphones and tried resetting ipod to no avail. Any ideas?

Does it still work in iPod docks or other adapters where it plugs into the bottom? That is what happened to mine and there was nothing they could do to fix it. I had a friend who said that he found a kit online to do it yourself, but that's risky. If it's still under warrenty, just take it in to an apple store and they should replace it. I was given the option to trade mine in for a brand new identical one for half price because I was past warrenty. They no longer made the 80g that I had anymore, so I ended up getting a 120g for the same price. I was prettty happy.

USB ports don't work after resuming from standby with Windows 8 on X230 tablet

I have just done a clean install of Windows 8 on my X230 tablet. Before installing Windows 8 I installed the most recent BIOS for this machine (version 2.50). After installing Windows 8 I installed System Update from the Lenovo Website and downloaded all the recommended drivers and other files. I've also installed all the latest Windows 8 updates.
Here are the symptoms of my problem: After resuming from standby/sleep mode, my USB ports do not work. My computer has two USB 3.0 ports and one USB 2.0 ports. All exhibit the same behavior. After resuming from standby mode I have tried inserting both my mouse and a USB thumbdrive, but neither are recognized. After restarting Windows, the USB ports work again... until I resume from standby mode again.
I hope there is a solution to this issue. It is very frustrating.

Thanks for the suggestion about tweaking the "Allow this computer to turn off this device" feature. I un-checked that box for every entry I could find under "Universal Serial Bus Controllers" in the Devide Manager. Unfortunately, the same symptoms of my problem persisted.
I went back and looked at the README file associated with the BIOS 2.50 download on Lenvo's support site. At the bottom of the file it gives a "Summary of Changes". Under version 2.03 of the BIOS (the version just before version 2.50), it says:
- (Fix) Fixed an issue where USB device might not detected when system resume from sleep mode.
This indicates that Lenovo support was already aware of such issues. The problem was intended to be fixed in version 2.03 of the BIOS. However, the issue persists on my machine, even with the latest BIOS.
Hopefully someone from Lenovo can comment here.

I just purchase a macbook air 13, used the bootcamp to install a windows 7 I had on CD and put on USB with a program, bud now the windows 7 don't work good, I have no internet connection and so no printer.

I read on the support / manual that I have to use Mac OS X Leopart intallation disk to install drivers for that windows.
Bud I don't have a cd like that...
So what do I do now?

Hello, So I understand that I can use bootcamp to do that...
I only take the 3 option in bootcamp, install Windows 7.
Do I have to deinstall Windows 7 and try it again with option 2 and 3 on in the boodcamp app?
I tried option 2 to download drivers on USB bud there is a network error so it won't work.
Thanks for helping me out.

German Umlaute don't work after upgrading to Yosemite with Japanese Romaji Layout set on U.S.

Hi everyone,
previously i could just use [ALT] + [U] and then press [A] / [a] / [U] / [u] / [O] / [o] to generate the german umlaut version.
After installing Yosemite this does not work anymore, which is kinda frustrating. Cause it forces me to add another keyboard layout and switch when i have to write a german umlaut.
I was previously using 'Input Source' > 'Japanese' > Enabled Romaji (Romaji layout was set to U.S.) & Hiragana.
For testing purpose i added the Standard U.S. Layout and writing the Umlaut with the keyboard shortcut still works there. So that's why i think this is a Romaji specific bug.
Has anyone any idea what's wrong ? Did Apple change something ?
Best Regards

Before I stumbled upon this thread, there was no flag at all. I had the character viewer there because pre-Yosemite it was the only way to access emoji (and things like arrows and other special symbols) in many apps (and still is for my Adobe CS5 apps). Additionally, I would use the keyboard viewer from time to time as a way to learn which keys to use for other special symbols (bring up the keyboard viewer and press option or shift-option or other combinations and it would show you a preview of what each key would generate).
While reading this thread, I added more input sources (US International and US Extended) and would see the flags. The flags replaced the previous character/keyboard viewer menu icon. I switched between each flag to test my issue under each, to no avail. Then I tried adding the Spanish keyboard but still had the same issue.
Now I've removed all the input sources except the primary US keyboard. There is no longer a flag in my menu, it's gone back to the character viewer icon.
The issue is still there. When I type option-r, u, or g, in any app nothing happens at all.
Unfortunately, neither auto-substitution nor press-and-hold work in Adobe CS5 apps, which is where I need to use these special characters the most.
Thank you for reaching out

File managers don't work, might have to do with FAM?

So I've tried both thunar and pcmanfm and they fail to open directories when I click them, so I replaced gamin with FAM, and it didn't work, so I switched back and it didn't work.
Can anyone help me?

i think have the same problem. When i start pcmanfm i can exactly one time change to any directory with the mouse. after that nothing gets highlited and nothing happens on double click. navigating with keyboard or by typing something in the adress bar works fine though. Thunar gave me similar behaviour, but nautilus works fine.
I'am on x86_64 testing.
we should move this discussion over here: http://bbs.archlinux.org/viewtopic.php?id=94272
Last edited by uwinkelvos (2010-04-09 19:46:48)

AX works (client Mode), but odd IP address and flashing orange light

Hi,
Today, possibly after a very brief power cut, my AX stopped working, then seemed OK after restarting my network. However, although I can play over Airtunes, the AX orange LED is continually flashing, and the AX has an odd (self-assigned?) IP address. I can't work this out.
I tried setting it up from scratch. Using the Airport Setup Assistant, tried to connect directly via Ethernet from my laptop (with Airport turned off). It asked me to switch on Airport, briefly found the AX, then refused to find it again.
So, I removed the Ethernet cable and tried using Airport Admin Utility wirelessly. I could connect to the AX as it started up from a hard reset, and I could set it up. However, although it still serves Airtunes, it still refuses to pick up a proper IP address (192.168....), instead having a 169.254... address. And the orange LED still flashes continuously.
I'm connecting to a closed network, using WPA Personal. AX version 6.3. Mac OS X 10.4.9.
The AX connects wirelessly to a LinkSys AP, which is in turn wired to an Airport Extreme BS, which is in turn wired (via a switch) to a LinkSys (wireless) router (long cable runs, thick walls, don't ask!). All has worked flawlessly for years. Still works, but looks like it shouldn't!
Any clues?

Hi. I'm actually having what seems to be the same problem, but after restarting and unplugging everything I can think of, the amber light is still flashing. Other than the light and the 69.47.... IP address (which I'll take your word for it being weird), the network appears to be working fine. Should I just ignore the light? We have three computers connected to it successfully right now, and I'd hate to disturb its mojo if the light isn't important.
Thanks!

My camera app and snapchat camera don't work. They won't flip cameras and camera app won't even come up

I have a 2 week old iPhone 5s. It just started yesterday. My camera app won't even come up and my snapchat camera won't switch cameras. What is wrong with my phone. I have reset it a million times and turned it off. None of it works. Help me.

Try a hard reset (reboot)
press and hold the home and power buttons until the Apple icon is displayed, then let go.

HT4085 How do I lock my ipad screen so the swipe action and side button on screen don't work? My cats do these things and the game disappears.

How do I lock my ipad screen so the swipe action and the side button on the screen do not work? When my cats play a game on my ipad, they regularly swipe the screen and push the side button and the game disappears.

The button on the top that you use to lock and unlock or put to sleep is the power button. The button lower center of the screen is the home button...can be used to also wake from sleep and switch to the base home screen.
Good to hear you are now able to lock rotation, even if you are not sure how you did it
If you go to the iBook icon, tap Store in the uppper left side of the screen, you can search for the iPad User Guide...a free download that will place the guide in your iBooks library as a great source of background information.

WLC 2504 don't work with mode trunking dot1Q with 3560cg and 2960cg?

Similar Messages

Maybe you are looking for