WLC 2504 max AP support
Hi all,
Does anybody know what is the maximum number of APs supported on Cisco 2504 WLC?
According to the Data Sheet it is 75:
http://www.cisco.com/en/US/prod/collateral/wireless/ps6302/ps8322/ps11630/data_sheet_c78-645111.html
But according to the config guide it is 50:
http://www.cisco.com/en/US/docs/wireless/controller/7.3/configuration/guide/b_wlc-cg_chapter_01.html#ID263
I believe the correct number is 50, but I just want to be sure.
Is this a software limitation?
Hi Leo
Don't think there's going to be any change on wism2 on supported AP limit.
Hi George
whenever new client added to WLC it needs some memory to seat the client on wlc, guess 2500 got room for that.
i think throughput of 2500 also getting doubled to 1gb from 500mb to increase performance.
Similar Messages
-
WLC: 2504
Firmware: 7.6.100
Hello,
I'm getting very confused in how to set up redundancy with WLC 2504. Some sources talk about Client SSO, some about N+1.
But it seems that although I should use Client SSO with firmware 7.6, the WLC 2504 doesn't support it.
When I type config redundancy, I have no choice
>config redundancy ?
unit Configure redundancy unit [primary | secondary]
So I typed "config redundancy unit primary" on my 2504 and "config redundancy unit secondary" on my 2504-HA
And when I issue this command I have very little information
>show redundancy summary
Type of the Unit = Primary
Does someone has guidelines for redundancy with WLC 2504 on firmware 7.6 ?
Thank youHello,
Thank you both for your answers.
Something I didn't understand in the documentation is this.
Is there a replication of configuration between the WLC primary and the HA ? I did read that they should have different network settings (IP addresses) so I understand that there is not a total replication, what about the rest of the configuration ?
The only result I have when I issue a command on the WLC-HA is this
>show redundancy summary
Type of the Unit = Secondary
It doesn't look exactly what I see in the documentation.
Thank you -
This might be a really stupid question but I need to ask just so that I get a definitive answer. I have a customer that is using a WLC 2112 and has maxed out the licenses for the WLC. I have suggested for him to purchase a 2504 with 30 or 40 licenses to replace the existing 2112. He doesn't want to purchase 30 to 40 licenses and doesn't want to remove the 2112 from the network environment. He would rather purchase a WLC 2504 with 15 licenses and just add that into the network.
My question is, will there be a problem running a 2504 and a 2112 on the same network? Or can I just make one a primary and one a secondary?That should be fine. Just make sure the WLCs are running the same code version and everything should work fine. This is required for APs failover from one WLC to another. You don't want the APs upgrading or downgrading code versions every time the ap moves from the primary to the secondary WLC.
Sent from Cisco Technical Support iPhone App -
Why LAP1131AG and LAP11412 cannot to join WLC 2504?
I have WLC 2504, Cisco LAP1131AG and then Cisco LAP1142N. Why LAP1131AG and LAP11412 cannot to join WLC 2504?
this is error code at the Cisco LAP1131AG
*Sep 12 19:30:27.730: %CAPWAP-3-ERRORLOG: Go join a capwap controller
*Sep 12 19:30:27.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 192.168.100.10 peer_port: 5246
*Sep 12 19:30:57.001: DTLS_CLIENT_ERROR: ../capwap/base_capwap/dtls/base_capwap_dtls_connection_db.c:2051 Max retransmission count reached!
*Sep 12 19:31:27.000: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 192.168.100.10:5246
*Sep 12 19:31:32.083: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to administratively down
*Sep 12 19:31:32.083: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to administratively down
*Sep 12 19:31:32.085: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to up
*Sep 12 19:31:32.117: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does not have an Ip !!
*Sep 12 19:31:32.118: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to up
*Sep 12 19:31:33.083: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to down
*Sep 12 19:31:33.112: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to down
*Sep 12 19:31:33.117: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*Sep 12 19:31:34.104: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to up
*Sep 12 19:31:34.111: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*Sep 12 19:31:34.142: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to up
*Sep 12 19:31:34.147: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to down
*Sep 12 19:31:34.152: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset
*Sep 12 19:31:35.141: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
*Sep 12 19:31:35.146: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to down
*Sep 12 19:31:35.170: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to up
*Sep 12 19:31:36.171: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to up
this is version LAP1131AG
AP0018.18fc.fd58#sh version
Cisco IOS Software, C1130 Software (C1130-K9W8-M), Version 12.4(25e)JAO6, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2014 by Cisco Systems, Inc.
Compiled Fri 22-Aug-14 10:07 by prod_rel_team
ROM: Bootstrap program is C1130 boot loader
BOOTLDR: C1130 Boot Loader (C1130-BOOT-M) Version 12.3(7)JA1, RELEASE SOFTWARE (fc1)
AP0018.18fc.fd58 uptime is 9 minutes
System returned to ROM by power-on
System image file is "flash:/c1130-k9w8-mx.124-25e.JAO6/c1130-k9w8-mx.124-25e.JAO6"
and then this is version WLC2504
(Cisco Controller) >show sysinfo
Manufacturer's Name.............................. Cisco Systems Inc.
Product Name..................................... Cisco Controller
Product Version.................................. 7.6.130.0
Bootloader Version............................... 1.0.20
Field Recovery Image Version..................... 7.6.101.1
Firmware Version................................. PIC 16.0
Build Type....................................... DATA + WPS
System Name...................................... Cisco_47:19:c4
System Location..................................
System Contact...................................
System ObjectID.................................. 1.3.6.1.4.1.9.1.1279
IP Address....................................... 192.168.100.10
Last Reset....................................... Software reset
System Up Time................................... 0 days 0 hrs 36 mins 45 secs
System Timezone Location.........................
System Stats Realtime Interval................... 5
System Stats Normal Interval..................... 180
--More-- or (q)uit
Configured Country............................... ID - Indonesia
Operating Environment............................ Commercial (0 to 40 C)
Internal Temp Alarm Limits....................... 0 to 65 C
Internal Temperature............................. +34 C
External Temperature............................. +40 C
Fan Status....................................... 4100 rpm
State of 802.11b Network......................... Enabled
State of 802.11a Network......................... Enabled
Number of WLANs.................................. 1
Number of Active Clients......................... 0
Burned-in MAC Address............................ 24:E9:B3:47:19:C0
Maximum number of APs supported.................. 5
IP Address management WLC : 192.168.100.10/24
IP Address LAP1142N :192.168.100.102/24
IP Address LAP1131AG : 192.168.100.101/24
Can anyone help my problem?A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
[email protected]
cisco AIR-LAP1142N-A-K9 (PowerPC405ex) processor (revision A0) with 90102K/40960K bytes of memory.
Processor board ID FGL1439S15W
PowerPC405ex CPU at 586MHz, revision number 0x147E
Last reset from reload
LWAPP image version 7.6.130.0
1 Gigabit Ethernet interface
2 802.11 Radios
32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: C8:4C:75:79:EB:E9
Part Number : 73-12836-03
PCA Assembly Number : 800-33767-03
PCA Revision Number : A0
PCB Serial Number : FOC14234D8Z
Top Assembly Part Number : 800-33775-02
Top Assembly Serial Number : FGL1439S15W
Top Revision Number : A0
Product/Model Number : AIR-LAP1142N-A-K9
cisco AIR-LAP1131AG-A-K9 (PowerPCElvis) processor (revision A0) with 27638K/5120K bytes of memory.
Processor board ID FTX1026T46E
PowerPCElvis CPU at 262Mhz, revision number 0x0950
Last reset from power-on
LWAPP image version 7.6.130.0
1 FastEthernet interface
2 802.11 Radio(s)
32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: 00:18:18:FC:FD:58
Part Number : 73-8962-09
PCA Assembly Number : 800-24818-08
PCA Revision Number : A0
PCB Serial Number : FOC102513DE
Top Assembly Part Number : 800-25544-06
Top Assembly Serial Number : FTX1026T46E
Top Revision Number : A0
Product/Model Number : AIR-LAP1131AG-A-K9
Configuration register is 0xF -
WLC 2504 sudden network instability
Hello,
we're running a WLC 2504 with two SSIDs on it. It is connected to to a small PoE switch. Standard untagged vlan. A handfull APs connected to it. No DHCP, the APs have all static IP addresses.
All of a sudden we're having a number of issues with the network connection:
APs restarting
The APs restart every now and then reporting that their IP is being used by another device. Looking through the logs there are two MAC addresses that are reported as using the APs IP address. These two MAC addresses have unknown vendor IDs.
Warning: AP with Base Radio MAC f8:72:ea:7c:9d:e3 has found its IP Address 0.2.146.0 being used by a machine with MAC
Address 04:c6:f8:40:00:00 (The other mac that is reported is 04:cc:90:40:00:00)
AP 'AP5', MAC: 0c:68:03:dd:1b:80 disassociated previously due to Link Failure. Uptime: 4 days, 00 h 48 m 50 s . Reason: Capwap WTP Event request.
So: There are two MACs that use the IP addresses of 7 APs?!?! And there is no vendor to be found for these MACs?
Ping timouts on the webGUI and CLI
I have a ping running on the IP for managing the device. This is running fine for ages. As soon as I connect via webGUI or CLI I lose packets. Get timeouts etc. some packets get through some don't. More of the latter. So ping is fine but any other traffic seems to be impacted heavily.
What we have done for troubleshooting
Checked duplex/speed settings of the interfaces. Everything ok.
Connected to another switchport. Same.
Changed the IP address of the management port. Same.
Swapped places with a laptop with the same IP address --> Worked fine.
Plugged in a completely new device, installed the latest firmware (7.6) and uploaded the config from the other one. Same.
Restarted the default gateway for the subnet the controler is on.
So now we're at the end of our knowledge. It seems to be a non-physical network issue, but we're a small team and no one has changed anything they say :-/
Any ideas what we could check next?
KatHello,
thanks for your suggestions. It's hard to find those two MAC addresses. As they seem to be virtual I cannot get a hint from the vendor ID. A show mac-address table on the switch the WLC is connected to doesn't show those two
I found an error in the WLC AP config. AP1 had the same IP as AP5 and a wrong netmask. I changed that. Unfortunately that doesn't solve our problem.
Here are some more messages from the WLC's log:
AP 'AP3', MAC: 0c:68:03:dd:34:00 disassociated previously due to Link Failure. Uptime: 4 days, 15 h 04 m 15 s . Reason: Capwap WTP Event request.
AP Disassociated. Base Radio MAC:0c:68:03:dd:34:00
AP's Interface:1(802.11a) Operation State Down: Base Radio MAC:0c:68:03:dd:34:00 Cause=Heartbeat Timeout Status:NA
AP 'AP3', MAC: 0c:68:03:dd:34:00 disassociated previously due to Link Failure. Uptime: 4 days, 15 h 00 m 45 s . Reason: Capwap WTP Event request.
RF Manager updated TxPower for Base Radio MAC: 0c:68:03:dd:34:00 and slotNo: 0. New Tx Power is: 2
AP's Interface:0(802.11b) Operation State Down: Base Radio MAC:0c:68:03:dd:16:e0 Cause=Max Retransmission Status:NA
IDS Signature attack detected. Signature Type: Standard, Name: Deauth flood, Description: Deauthentication flood, Track: per-signature, Detecting AP Name: AP7, Radio Type: 802.11b/g, Preced: 9, Hits: 500, Channel: 6, srcMac: C2:9F:DB:21:47:60
This is the sh run-config of our WLC including one AP:
>show run-config
System Inventory
NAME: "Chassis" , DESCR: "Cisco 2500 Series Wireless LAN Controller"
PID: AIR-CT2504-K9, VID: V01, SN: PSZ17381EPZ
Burned-in MAC Address............................ 50:17:FF:27:12:80
Maximum number of APs supported.................. 15
System Information
Manufacturer's Name.............................. Cisco Systems Inc.
Product Name..................................... Cisco Controller
Product Version.................................. 7.4.110.0
Bootloader Version............................... 1.0.18
Field Recovery Image Version..................... 1.0.0
Firmware Version................................. PIC 16.0
Build Type....................................... DATA + WPS
System Name...................................... UK-BRI-WFAPC
System Location..................................
System Contact...................................
System ObjectID.................................. 1.3.6.1.4.1.9.1.1279
IP Address....................................... 172.17.128.12
Last Reset....................................... Power on reset
System Up Time................................... 4 days 0 hrs 46 mins 6 secs
System Timezone Location.........................
System Stats Realtime Interval................... 5
System Stats Normal Interval..................... 180
Configured Country............................... GB - United Kingdom
Operating Environment............................ Commercial (0 to 40 C)
Internal Temp Alarm Limits....................... 0 to 65 C
Internal Temperature............................. +20 C
External Temperature............................. +25 C
Fan Status....................................... 4000 rpm
State of 802.11b Network......................... Enabled
State of 802.11a Network......................... Enabled
Number of WLANs.................................. 3
Number of Active Clients......................... 6
Memory Current Usage............................. Unknown
Memory Average Usage............................. Unknown
CPU Current Usage................................ Unknown
CPU Average Usage................................ Unknown
Burned-in MAC Address............................ 50:17:FF:27:12:80
Maximum number of APs supported.................. 15
AP Bundle Information
Primary AP Image Size
ap1g2 9568
ap3g1 11288
ap3g2 11196
ap801 7164
ap802 8568
c1130 5072
c1140 9416
c1250 6944
c1520 8044
c602i 3736
Secondary AP Image Size
ap3g1 5792
ap801 5192
ap802 5232
c1100 3084
c1130 4964
c1140 4992
c1200 3364
c1240 4812
c1250 5504
c1310 3136
c1520 6404
c3201 4324
c602i 3716
Switch Configuration
802.3x Flow Control Mode......................... Disable
FIPS prerequisite features....................... Disabled
secret obfuscation............................... Enabled
Strong Password Check Features:
case-check ...........Enabled
consecutive-check ....Enabled
default-check .......Enabled
username-check ......Enabled
Network Information
RF-Network Name............................. RFGROUP
Web Mode.................................... Disable
Secure Web Mode............................. Enable
Secure Web Mode Cipher-Option High.......... Disable
Secure Web Mode Cipher-Option SSLv2......... Disable
Secure Web Mode RC4 Cipher Preference....... Disable
OCSP........................................ Disabled
OCSP responder URL..........................
Secure Shell (ssh).......................... Enable
Telnet...................................... Disable
Ethernet Multicast Forwarding............... Disable
Ethernet Broadcast Forwarding............... Disable
AP Multicast/Broadcast Mode................. Multicast Address : 0.0.0.0
IGMP snooping............................... Disabled
IGMP timeout................................ 60 seconds
IGMP Query Interval......................... 20 seconds
MLD snooping................................ Disabled
MLD timeout................................. 60 seconds
MLD query interval.......................... 20 seconds
User Idle Timeout........................... 300 seconds
ARP Idle Timeout............................ 300 seconds
Cisco AP Default Master..................... Disable
AP Join Priority............................ Disable
Mgmt Via Wireless Interface................. Disable
Mgmt Via Dynamic Interface.................. Disable
Bridge MAC filter Config.................... Enable
Bridge Security Mode........................ EAP
Mesh Full Sector DFS........................ Enable
AP Fallback ................................ Enable
Web Auth CMCC Support ...................... Disabled
Web Auth Redirect Ports .................... 80
Web Auth Proxy Redirect ................... Disable
Web Auth Captive-Bypass .................. Disable
Web Auth Secure Web ....................... Enable
Fast SSID Change ........................... Disabled
AP Discovery - NAT IP Only ................. Enabled
IP/MAC Addr Binding Check .................. Enabled
CCX-lite status ............................ Disable
oeap-600 dual-rlan-ports ................... Disable
oeap-600 local-network ..................... Enable
mDNS snooping............................... Disabled
mDNS Query Interval......................... 15 minutes
Port Summary
STP Admin Physical Physical Link Link
Pr Type Stat Mode Mode Status Status Trap POE
1 Normal Forw Enable Auto 1000 Full Up Enable N/A
2 Normal Forw Enable Auto 100 Full Up Enable N/A
3 Normal Forw Enable Auto 1000 Full Up Enable Enable (Power Off)
4 Normal Disa Enable Auto Auto Down Enable Enable (Power Off)
AP Summary
Number of APs.................................... 7
Global AP User Name.............................. Not Configured
Global AP Dot1x User Name........................ Not Configured
AP Name Slots AP Model Ethernet MAC Location Port Country Priority
AP7 2 AIR-CAP1602I-E-K9 f8:72:ea:e4:9a:81 default location 1 GB 1
AP1 2 AIR-CAP1602I-E-K9 f8:72:ea:7c:9d:e3 default location 1 GB 1
AP3 2 AIR-CAP1602I-E-K9 f8:72:ea:e4:9c:57 default location 1 GB 1
AP6 2 AIR-CAP1602I-E-K9 f8:72:ea:e4:9a:90 default location 1 GB 1
AP2 2 AIR-CAP1602I-E-K9 f8:72:ea:7c:9b:63 default location 1 GB 1
AP4 2 AIR-CAP1602I-E-K9 f8:72:ea:e4:9a:9b default location 1 GB 1
AP5 2 AIR-CAP1602I-E-K9 f8:72:ea:e4:9a:cb default location 1 GB 1
AP Tcp-Mss-Adjust Info
AP Name TCP State MSS Size
AP7 disabled -
AP1 disabled -
AP3 disabled -
AP6 disabled -
AP2 disabled -
AP4 disabled -
AP5 disabled -
AP Location
Total Number of AP Groups........................ 0
Site Name........................................ default-group
Site Description.................................
NAS-identifier................................... UK-BRI-WFAPC
AP Operating Class............................... Not-configured
RF Profile
2.4 GHz band.....................................
5 GHz band.......................................
WLAN ID Interface Network Admission Control Radio Policy
1 corporate Disabled None
2 dirtynetwork Disabled None
3 dirtynetwork Disabled None
AP Name Slots AP Model Ethernet MAC Location Port Country Priority
AP7 2 AIR-CAP1602I-E-K9 f8:72:ea:e4:9a:81 default location 1 GB 1
AP1 2 AIR-CAP1602I-E-K9 f8:72:ea:7c:9d:e3 default location 1 GB 1
AP3 2 AIR-CAP1602I-E-K9 f8:72:ea:e4:9c:57 default location 1 GB 1
AP6 2 AIR-CAP1602I-E-K9 f8:72:ea:e4:9a:90 default location 1 GB 1
AP2 2 AIR-CAP1602I-E-K9 f8:72:ea:7c:9b:63 default location 1 GB 1
AP4 2 AIR-CAP1602I-E-K9 f8:
RF Profile
Number of RF Profiles............................ 0
Out Of Box State................................. Disabled
RF Profile Name Band Description 11n-client-only
AP Config
Cisco AP Identifier.............................. 15
Cisco AP Name.................................... AP7
Country code..................................... GB - United Kingdom
Regulatory Domain allowed by Country............. 802.11bg:-E 802.11a:-E
AP Country code..................
................ GB - United Kingdom
AP Regulatory Domain............................. -E
Switch Port Number .............................. 1
MAC Address...................................... f8:72:ea:e4:9a:81
IP Address Configuration......................... Static IP assigned
IP Address....................................... 172.17.128.24
IP NetMask....................................... 255.255.128.0
Gateway IP Addr.................................. 172.17.128.1
Domain...............
Name Server......................................
NAT External IP Address.......................... None
CAPWAP Path MTU.................................. 1485
Telnet State..................................... Disabled
Ssh State........................................ Disabled
Cisco AP Location................................ default location
Cisco AP Floor Label............................. 0
Cisco AP Group Name.............................. default-group
Primary Cisco Switch Name........................
Primary Cisco Switch IP Address.................. Not Configured
Secondary Cisco Switch Name......................
Secondary Cisco Switch IP Address................ Not Configured
Tertiary Cisco Switch Name.......................
Tertiary Cisco Switch IP Address................. Not Configured
Administrative State ............................ ADMIN_ENABLED
Operation State ....
............................. REGISTERED
Mirroring Mode .................................. Disabled
AP Mode ......................................... Local
Public Safety ................................... Disabled
AP SubMode ...................................... Not Configured
Remote AP Debug ................................. Disabled
Logging trap severity level ..................... informational
Logging syslog facility ..
....................... kern
S/W Version .................................... 7.4.110.0
Boot Version ................................... 15.2.2.0
Mini IOS Version ................................ 7.4.1.37
Stats Reporting Period .......................... 180
Stats Collection Mode ........................... normal
LED State........................................
Enabled
PoE Pre-Standard Switch.......................... Disabled
PoE Power Injector MAC Addr...................... Disabled
Power Type/Mode.................................. Power injector / Normal mode
Number Of Slots.................................. 2
AP Model......................................... AIR-CAP1602I-E-K9
AP Image...............................
.......... C1600-K9W8-M
IOS Version...................................... 15.2(2)JB2$
Reset Button..................................... Enabled
AP Serial Number................................. FGL1725W7F7
AP Certificate Type.............................. Manufacture Installed
AP User Mode..................................... AUTOMATIC
AP User Name..................................... Not Configured
AP Dot1x User Mode............................... Not Configured
AP Dot1x User Name............................... Not Configured
Cisco AP system loggi
ng host..................... 255.255.255.255
AP Up Time....................................... 3 days, 23 h 26 m 50 s
AP LWAPP Up Time................................. 0 days, 00 h 14 m 12 s
Join Date and Time............................... Tue Jan 28 18:11:43 2014
Join Taken Time.................................. 0 days, 00 h 11 m 41 s
Attributes for Slot 0
Radio Type................................... RADIO_TYPE_80211n-2.4
Administrative State ........................ ADMIN_ENABLED
Operation State ............................. UP
Radio Role .................................. ACCESS
Radio Mode .................................. Local
CellId ...................................... 0
Station Configuration
Configuration ............................. AU
TOMATIC
Number Of WLANs ........................... 3
Medium Occupancy Limit .................... 100
CFP Period ................................ 4
CFP MaxDuration ........................... 60
BSSID ..................................... 0c:68:03:dd:16:e0
Operation Rate Set
1000 Kilo Bits........................... MANDATORY
2000 Kilo Bits........................... MANDATORY
5500 Kilo Bits........................... MANDATORY
11000 Kilo Bits.......................... MANDATORY
6000 Kilo Bits........................... SUPPORTED
9000 Kilo Bits........................... SUPPORTED
12000 Kilo Bits.......................... SUPPORTED
18000 Kilo Bits.......................... SUPPORTED
24000 Kilo Bits.......................... SUPPORTED
36000 Kilo Bits.......................... SUPPORTED
48000 Kilo Bits.......................... SUPPORTED
54000 Kilo Bits.......................... SUPPORTED
MCS Set
MCS 0.................................... SUPPORTED
MCS 1.................................... SUPPORTED
MCS 2.................................... SUPPORTED
MCS 3.................................... SUPPORTED
MCS 4.................................... SUPPORTED
MCS 5.................................... SUPPORTED
MCS 6.................................... SUPPORTED
MCS 7.................................... SUPPORTED
MCS 8.................................... SUPPORTED
MCS 9.................................... SUPPORTED
MCS 10................................... SUPPORTED
MCS 11................................... SUPPORTED
MCS 12..
................................. SUPPORTED
MCS 13................................... SUPPORTED
MCS 14................................... SUPPORTED
MCS 15................................... SUPPORTED
MCS 16................................... DISABLED
MCS 17................................... DISABLED
MCS 18................................... DISABLED
MCS 19................................... DISABLED
MCS 20................................... DISABLED
MCS 21................................... DISABLED
MCS 22................................... DISABLED
MCS 23................................... DISABLED
Beacon Period ............................. 100
Fragmentation Threshold ................... 2346
Multi Domain Capability Implemented ....... TRUE
Multi Domain Capability Enabled ........... TRUE
Country String ............................ GB
Multi Domain Capability
Configuration ............................. AUTOMATIC
First Chan Num ............................ 1
Number Of Channels ........................ 13
MAC Operation Parameters
Configuration ............................. AUTOMATIC
Fragmentation Threshold ................... 2346
Packet Retry Limit ........................ 64
Tx Power
Num Of Supported Power Levels ............. 4
Tx Power Level 1 .......................... 16 dBm
Tx Power Level 2 .......................... 13 dBm
Tx Power Level 3 .......................... 10 dBm
Tx Power Level 4 .......................... 7 dBm
Tx Power Configuration .................... AUTOMATIC
Current Tx Power Level .................... 3
Tx Power Assigned By ...................... DTPC
Phy OFDM parameters
Configuration ............................. AUTOMATIC
Current Channel ........................... 6
Channel Assigned By ....................... DCA
Extension Channel ......................... NONE
Channel Width.............................. 20 Mhz
Allowed Channel List....................... 1,2,3,4,5,6,7,8,9,10,11,12,
......................................... 13
TI Threshold .............................. -50
Legacy Tx Beamforming Configuration ....... CUSTOMIZED
Legacy Tx Beamforming ..................... ENABLED
Antenna Type............................... INTERNAL_ANTENNA
Internal Antenna Gain (in .5 dBi units).... 8
Diversity.................................. DIVERSITY_ENABLED
802.11n Antennas
A....................................... ENABLED
B....................................... ENABLED
C....................................... ENABLED
Performance Profile Parameters
Configuration ............................. AUTOMATIC
Interference threshold..................... 10 %
Noise threshold............................ -70 dBm
RF utilization threshold................... 80 %
Data-rate threshold........................ 1000000 bps
Client threshold........................... 12 clients
Coverage SNR threshold..................... 12 dB
Coverage exception level................... 25 %
Client minimum exception level............. 3 clients
Rogue Containment Information
Containment Count............................
CleanAir Management Information
CleanAir Capable......................... No
Radio Extended Configurations
Beacon period.............................. 100 milliseconds
Beacon range............................... AUTO
Multicast buffer........................... AUTO
Multicast data-rate........................ AUTO
RX SOP threshold........................... AUTO
CCA threshold.............................. AUTO -
Client got not connection to wlan over wlc 2504 on 802.11b/g
Hi everybody,
We are using a wlc 2504 with 7.6.100.0 and AP 1532e.
I have the strange observacion that only clients with 802.11n (2.4GHz) can connect to the WLAN. Clients thats works only with 802.11b/g, they can't connect to the WLAN. Affected are all machines which want to connect with 802.11b/g.
This is a MESH WLAN with 5GHz backhaul and 2.4GHz for the user.
During the debugging found the following:
*apfMsConnTask_4: May 09 11:44:40.581: 00:1b:77:b4:34:e0 Sending Assoc Response to station on BSSID 18:9c:5d:71:34:50 (status 0) ApVapId 1 Slot 0
*apfMsConnTask_4: May 09 11:44:40.581: 00:1b:77:b4:34:e0 apfProcessAssocReq (apf_80211.c:8292) Changing state for mobile 00:1b:77:b4:34:e0 on AP 18:9c:5d:71:34:50 from Associated to Associated
*spamApTask6: May 09 11:44:40.584: 00:1b:77:b4:34:e0 Sent 1x initiate message to multi thread task for mobile 00:1b:77:b4:34:e0
*Dot1x_NW_MsgTask_0: May 09 11:44:40.584: 00:1b:77:b4:34:e0 Creating a PKC PMKID Cache entry for station 00:1b:77:b4:34:e0 (RSN 2)
*Dot1x_NW_MsgTask_0: May 09 11:44:40.584: 00:1b:77:b4:34:e0 Resetting MSCB PMK Cache Entry 0 for station 00:1b:77:b4:34:e0
*Dot1x_NW_MsgTask_0: May 09 11:44:40.584: 00:1b:77:b4:34:e0 Setting active key cache index 8 ---> 8
*Dot1x_NW_MsgTask_0: May 09 11:44:40.584: 00:1b:77:b4:34:e0 Setting active key cache index 8 ---> 0
*Dot1x_NW_MsgTask_0: May 09 11:44:40.584: 00:1b:77:b4:34:e0 Adding BSSID 18:9c:5d:71:34:50 to PMKID cache at index 0 for station 00:1b:77:b4:34:e0
*Dot1x_NW_MsgTask_0: May 09 11:44:40.584: New PMKID: (16)
*Dot1x_NW_MsgTask_0: May 09 11:44:40.584: [0000] f6 3d 52 9f 2a de 52 90 1d a2 46 49 0f 14 f6 69
*Dot1x_NW_MsgTask_0: May 09 11:44:40.584: 00:1b:77:b4:34:e0 Initiating RSN PSK to mobile 00:1b:77:b4:34:e0
*Dot1x_NW_MsgTask_0: May 09 11:44:40.584: 00:1b:77:b4:34:e0 EAP-PARAM Debug - eap-params for Wlan-Id :1 is disabled - applying Global eap timers and retries
*Dot1x_NW_MsgTask_0: May 09 11:44:40.584: 00:1b:77:b4:34:e0 dot1x - moving mobile 00:1b:77:b4:34:e0 into Force Auth state
*Dot1x_NW_MsgTask_0: May 09 11:44:40.584: 00:1b:77:b4:34:e0 EAPOL Header:
*Dot1x_NW_MsgTask_0: May 09 11:44:40.584: 00000000: 02 03 00 5f ..._
*Dot1x_NW_MsgTask_0: May 09 11:44:40.584: 00:1b:77:b4:34:e0 Found an cache entry for BSSID 18:9c:5d:71:34:50 in PMKID cache at index 0 of station 00:1b:77:b4:34:e0
*Dot1x_NW_MsgTask_0: May 09 11:44:40.584: 00:1b:77:b4:34:e0 Found an cache entry for BSSID 18:9c:5d:71:34:50 in PMKID cache at index 0 of station 00:1b:77:b4:34:e0
*Dot1x_NW_MsgTask_0: May 09 11:44:40.584: Including PMKID in M1 (16)
*Dot1x_NW_MsgTask_0: May 09 11:44:40.584: [0000] f6 3d 52 9f 2a de 52 90 1d a2 46 49 0f 14 f6 69
*Dot1x_NW_MsgTask_0: May 09 11:44:40.584: 00:1b:77:b4:34:e0 Starting key exchange to mobile 00:1b:77:b4:34:e0, data packets will be dropped
*Dot1x_NW_MsgTask_0: May 09 11:44:40.584: 00:1b:77:b4:34:e0 Sending EAPOL-Key Message to mobile 00:1b:77:b4:34:e0
state INITPMK (message 1), replay counter 00.00.00.00.00.00.00.00
*Dot1x_NW_MsgTask_0: May 09 11:44:40.584: 00:1b:77:b4:34:e0 Sending EAPOL-Key Message to mobile 00:1b:77:b4:34:e0
state INITPMK (message 1), replay counter 00.00.00.00.00.00.00.00
*Dot1x_NW_MsgTask_0: May 09 11:44:40.584: 00:1b:77:b4:34:e0 Allocating EAP Pkt for retransmission to mobile 00:1b:77:b4:34:e0
*Dot1x_NW_MsgTask_0: May 09 11:44:40.585: 00:1b:77:b4:34:e0 mscb->apfMsLwappLradNhMac = 78:da:6e:59:c9:8c mscb->apfMsLradSlotId = 0 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
*Dot1x_NW_MsgTask_0: May 09 11:44:40.585: 00:1b:77:b4:34:e0 mscb->apfMsBssid = 18:9c:5d:71:34:50 mscb->apfMsAddress = 00:1b:77:b4:34:e0 mscb->apfMsApVapId = 1
*Dot1x_NW_MsgTask_0: May 09 11:44:40.585: 00:1b:77:b4:34:e0 dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 0 mscb->apfMsLwappMwarInet.ipv4.addr = -1062679171
*Dot1x_NW_MsgTask_0: May 09 11:44:40.585: 00:1b:77:b4:34:e0 mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = -1062679163 mscb->apfMsLwappLradPort = 40089
*osapiBsnTimer: May 09 11:44:42.649: 00:1b:77:b4:34:e0 802.1x 'timeoutEvt' Timer expired for station 00:1b:77:b4:34:e0 and for message = M2
*dot1xMsgTask: May 09 11:44:42.649: 00:1b:77:b4:34:e0 Retransmit 1 of EAPOL-Key M1 (length 121) for mobile 00:1b:77:b4:34:e0
*dot1xMsgTask: May 09 11:44:42.649: 00:1b:77:b4:34:e0 mscb->apfMsLwappLradNhMac = 78:da:6e:59:c9:8c mscb->apfMsLradSlotId = 0 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
*dot1xMsgTask: May 09 11:44:42.649: 00:1b:77:b4:34:e0 mscb->apfMsBssid = 18:9c:5d:71:34:50 mscb->apfMsAddress = 00:1b:77:b4:34:e0 mscb->apfMsApVapId = 1
*dot1xMsgTask: May 09 11:44:42.649: 00:1b:77:b4:34:e0 dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 0 mscb->apfMsLwappMwarInet.ipv4.addr = -1062679171
*dot1xMsgTask: May 09 11:44:42.649: 00:1b:77:b4:34:e0 mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = -1062679163 mscb->apfMsLwappLradPort = 40089
*osapiBsnTimer: May 09 11:44:44.649: 00:1b:77:b4:34:e0 802.1x 'timeoutEvt' Timer expired for station 00:1b:77:b4:34:e0 and for message = M2
*dot1xMsgTask: May 09 11:44:44.649: 00:1b:77:b4:34:e0 Retransmit 2 of EAPOL-Key M1 (length 121) for mobile 00:1b:77:b4:34:e0
*dot1xMsgTask: May 09 11:44:44.649: 00:1b:77:b4:34:e0 mscb->apfMsLwappLradNhMac = 78:da:6e:59:c9:8c mscb->apfMsLradSlotId = 0 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
*dot1xMsgTask: May 09 11:44:44.649: 00:1b:77:b4:34:e0 mscb->apfMsBssid = 18:9c:5d:71:34:50 mscb->apfMsAddress = 00:1b:77:b4:34:e0 mscb->apfMsApVapId = 1
*dot1xMsgTask: May 09 11:44:44.649: 00:1b:77:b4:34:e0 dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 0 mscb->apfMsLwappMwarInet.ipv4.addr = -1062679171
*dot1xMsgTask: May 09 11:44:44.650: 00:1b:77:b4:34:e0 mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = -1062679163 mscb->apfMsLwappLradPort = 40089
*osapiBsnTimer: May 09 11:44:46.649: 00:1b:77:b4:34:e0 802.1x 'timeoutEvt' Timer expired for station 00:1b:77:b4:34:e0 and for message = M2
*dot1xMsgTask: May 09 11:44:46.649: 00:1b:77:b4:34:e0 Retransmit failure for EAPOL-Key M1 to mobile 00:1b:77:b4:34:e0, retransmit count 3, mscb deauth count 1
*dot1xMsgTask: May 09 11:44:46.649: 00:1b:77:b4:34:e0 Resetting MSCB PMK Cache Entry 0 for station 00:1b:77:b4:34:e0
*dot1xMsgTask: May 09 11:44:46.649: 00:1b:77:b4:34:e0 Removing BSSID 18:9c:5d:71:34:50 from PMKID cache of station 00:1b:77:b4:34:e0
*dot1xMsgTask: May 09 11:44:46.649: 00:1b:77:b4:34:e0 Setting active key cache index 0 ---> 8
*dot1xMsgTask: May 09 11:44:46.649: 00:1b:77:b4:34:e0 Sent Deauthenticate to mobile on BSSID 18:9c:5d:71:34:50 slot 0(caller 1x_ptsm.c:598)
*dot1xMsgTask: May 09 11:44:46.649: 00:1b:77:b4:34:e0 Setting active key cache index 8 ---> 8
*dot1xMsgTask: May 09 11:44:46.649: 00:1b:77:b4:34:e0 Deleting the PMK cache when de-authenticating the client.
*dot1xMsgTask: May 09 11:44:46.649: 00:1b:77:b4:34:e0 Global PMK Cache deletion failed.
*dot1xMsgTask: May 09 11:44:46.649: 00:1b:77:b4:34:e0 Scheduling deletion of Mobile Station: (callerId: 57) in 10 seconds
*dot1xMsgTask: May 09 11:44:46.649: 00:1b:77:b4:34:e0 Freeing EAP Retransmit Bufer for mobile 00:1b:77:b4:34:e0
*apfMsConnTask_4: May 09 11:44:52.083: 00:1b:77:b4:34:e0 Reassociation received from mobile on BSSID 18:9c:5d:71:34:50
*apfMsConnTask_4: May 09 11:44:52.083: 00:1b:77:b4:34:e0 Global 200 Clients are allowed to AP radio
*apfMsConnTask_4: May 09 11:44:52.083: 00:1b:77:b4:34:e0 Max Client Trap Threshold: 0 cur: 1
*apfMsConnTask_4: May 09 11:44:52.083: 00:1b:77:b4:34:e0 Rf profile 600 Clients are allowed to AP wlan
*apfMsConnTask_4: May 09 11:44:52.083: 00:1b:77:b4:34:e0 Applying Interface policy on Mobile, role Unassociated. Ms NAC State 2 Quarantine Vlan 0 Access Vlan 1
*apfMsConnTask_4: May 09 11:44:52.083: 00:1b:77:b4:34:e0 Re-applying interface policy for client
*apfMsConnTask_4: May 09 11:44:52.083: 00:1b:77:b4:34:e0 0.0.0.0 START (0) Changing IPv4 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2202)
*apfMsConnTask_4: May 09 11:44:52.083: 00:1b:77:b4:34:e0 0.0.0.0 START (0) Changing IPv6 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2223)
*apfMsConnTask_4: May 09 11:44:52.083: 00:1b:77:b4:34:e0 apfApplyWlanPolicy: Apply WLAN Policy over PMIPv6 Client Mobility Type
*apfMsConnTask_4: May 09 11:44:52.083: 00:1b:77:b4:34:e0 In processSsidIE:4795 setting Central switched to TRUE
*apfMsConnTask_4: May 09 11:44:52.083: 00:1b:77:b4:34:e0 In processSsidIE:4798 apVapId = 1 and Split Acl Id = 65535
*apfMsConnTask_4: May 09 11:44:52.083: 00:1b:77:b4:34:e0 Applying site-specific Local Bridging override for station 00:1b:77:b4:34:e0 - vapId 1, site 'default-group', interface 'catodos'
*apfMsConnTask_4: May 09 11:44:52.083: 00:1b:77:b4:34:e0 Applying Local Bridging Interface Policy for station 00:1b:77:b4:34:e0 - vlan 1, interface id 12, interface 'catodos'
*apfMsConnTask_4: May 09 11:44:52.083: 00:1b:77:b4:34:e0 processSsidIE statusCode is 0 and status is 0
*apfMsConnTask_4: May 09 11:44:52.083: 00:1b:77:b4:34:e0 processSsidIE ssid_done_flag is 0 finish_flag is 0
*apfMsConnTask_4: May 09 11:44:52.083: 00:1b:77:b4:34:e0 STA - rates (8): 2 4 11 22 12 18 24 36 48 72 96 108 0 0 0 0
*apfMsConnTask_4: May 09 11:44:52.083: 00:1b:77:b4:34:e0 suppRates statusCode is 0 and gotSuppRatesElement is 1
*apfMsConnTask_4: May 09 11:44:52.083: 00:1b:77:b4:34:e0 STA - rates (12): 2 4 11 22 12 18 24 36 48 72 96 108 0 0 0 0
*apfMsConnTask_4: May 09 11:44:52.083: 00:1b:77:b4:34:e0 extSuppRates statusCode is 0 and gotExtSuppRatesElement is 1
*apfMsConnTask_4: May 09 11:44:52.083: 00:1b:77:b4:34:e0 Processing RSN IE type 48, length 20 for mobile 00:1b:77:b4:34:e0
*apfMsConnTask_4: May 09 11:44:52.083: 00:1b:77:b4:34:e0 0.0.0.0 START (0) Initializing policy
*apfMsConnTask_4: May 09 11:44:52.084: 00:1b:77:b4:34:e0 0.0.0.0 START (0) Change state to AUTHCHECK (2) last state START (0)
*apfMsConnTask_4: May 09 11:44:52.084: 00:1b:77:b4:34:e0 0.0.0.0 AUTHCHECK (2) Change state to 8021X_REQD (3) last state AUTHCHECK (2)
*apfMsConnTask_4: May 09 11:44:52.084: 00:1b:77:b4:34:e0 Central switch is TRUE
*apfMsConnTask_4: May 09 11:44:52.084: 00:1b:77:b4:34:e0 Not Using WMM Compliance code qosCap 00
*apfMsConnTask_4: May 09 11:44:52.084: 00:1b:77:b4:34:e0 0.0.0.0 8021X_REQD (3) Plumbed mobile LWAPP rule on AP 18:9c:5d:71:34:50 vapId 1 apVapId 1 flex-acl-name:
*apfMsConnTask_4: May 09 11:44:52.084: 00:1b:77:b4:34:e0 apfPemAddUser2 (apf_policy.c:333) Changing state for mobile 00:1b:77:b4:34:e0 on AP 18:9c:5d:71:34:50 from Associated to Associated
*apfMsConnTask_4: May 09 11:44:52.084: 00:1b:77:b4:34:e0 apfPemAddUser2:session timeout forstation 00:1b:77:b4:34:e0 - Session Tout 1800, apfMsTimeOut '1800' and sessionTimerRunning flag is 0
*apfMsConnTask_4: May 09 11:44:52.084: 00:1b:77:b4:34:e0 Scheduling deletion of Mobile Station: (callerId: 49) in 1800 seconds
*apfMsConnTask_4: May 09 11:44:52.084: 00:1b:77:b4:34:e0 Func: apfPemAddUser2, Ms Timeout = 1800, Session Timeout = 1800
*apfMsConnTask_4: May 09 11:44:52.084: 00:1b:77:b4:34:e0 Sending Assoc Response to station on BSSID 18:9c:5d:71:34:50 (status 0) ApVapId 1 Slot 0
*apfMsConnTask_4: May 09 11:44:52.084: 00:1b:77:b4:34:e0 apfProcessAssocReq (apf_80211.c:8292) Changing state for mobile 00:1b:77:b4:34:e0 on AP 18:9c:5d:71:34:50 from Associated to Associated
*spamApTask6: May 09 11:44:52.087: 00:1b:77:b4:34:e0 Sent 1x initiate message to multi thread task for mobile 00:1b:77:b4:34:e0
*Dot1x_NW_MsgTask_0: May 09 11:44:52.087: 00:1b:77:b4:34:e0 Creating a PKC PMKID Cache entry for station 00:1b:77:b4:34:e0 (RSN 2)
*Dot1x_NW_MsgTask_0: May 09 11:44:52.087: 00:1b:77:b4:34:e0 Resetting MSCB PMK Cache Entry 0 for station 00:1b:77:b4:34:e0
*Dot1x_NW_MsgTask_0: May 09 11:44:52.087: 00:1b:77:b4:34:e0 Setting active key cache index 8 ---> 8
*Dot1x_NW_MsgTask_0: May 09 11:44:52.087: 00:1b:77:b4:34:e0 Setting active key cache index 8 ---> 0
*Dot1x_NW_MsgTask_0: May 09 11:44:52.087: 00:1b:77:b4:34:e0 Adding BSSID 18:9c:5d:71:34:50 to PMKID cache at index 0 for station 00:1b:77:b4:34:e0
*Dot1x_NW_MsgTask_0: May 09 11:44:52.087: New PMKID: (16)
*Dot1x_NW_MsgTask_0: May 09 11:44:52.087: [0000] f6 3d 52 9f 2a de 52 90 1d a2 46 49 0f 14 f6 69
*Dot1x_NW_MsgTask_0: May 09 11:44:52.087: 00:1b:77:b4:34:e0 Initiating RSN PSK to mobile 00:1b:77:b4:34:e0
*Dot1x_NW_MsgTask_0: May 09 11:44:52.087: 00:1b:77:b4:34:e0 EAP-PARAM Debug - eap-params for Wlan-Id :1 is disabled - applying Global eap timers and retries
*Dot1x_NW_MsgTask_0: May 09 11:44:52.087: 00:1b:77:b4:34:e0 dot1x - moving mobile 00:1b:77:b4:34:e0 into Force Auth state
*Dot1x_NW_MsgTask_0: May 09 11:44:52.087: 00:1b:77:b4:34:e0 EAPOL Header:
*Dot1x_NW_MsgTask_0: May 09 11:44:52.087: 00000000: 02 03 00 5f ..._
*Dot1x_NW_MsgTask_0: May 09 11:44:52.087: 00:1b:77:b4:34:e0 Found an cache entry for BSSID 18:9c:5d:71:34:50 in PMKID cache at index 0 of station 00:1b:77:b4:34:e0
*Dot1x_NW_MsgTask_0: May 09 11:44:52.087: 00:1b:77:b4:34:e0 Found an cache entry for BSSID 18:9c:5d:71:34:50 in PMKID cache at index 0 of station 00:1b:77:b4:34:e0
*Dot1x_NW_MsgTask_0: May 09 11:44:52.087: Including PMKID in M1 (16)
*Dot1x_NW_MsgTask_0: May 09 11:44:52.087: [0000] f6 3d 52 9f 2a de 52 90 1d a2 46 49 0f 14 f6 69
*Dot1x_NW_MsgTask_0: May 09 11:44:52.087: 00:1b:77:b4:34:e0 Starting key exchange to mobile 00:1b:77:b4:34:e0, data packets will be dropped
*Dot1x_NW_MsgTask_0: May 09 11:44:52.087: 00:1b:77:b4:34:e0 Sending EAPOL-Key Message to mobile 00:1b:77:b4:34:e0
state INITPMK (message 1), replay counter 00.00.00.00.00.00.00.00
*Dot1x_NW_MsgTask_0: May 09 11:44:52.087: 00:1b:77:b4:34:e0 Sending EAPOL-Key Message to mobile 00:1b:77:b4:34:e0
state INITPMK (message 1), replay counter 00.00.00.00.00.00.00.00
*Dot1x_NW_MsgTask_0: May 09 11:44:52.087: 00:1b:77:b4:34:e0 Allocating EAP Pkt for retransmission to mobile 00:1b:77:b4:34:e0
*Dot1x_NW_MsgTask_0: May 09 11:44:52.087: 00:1b:77:b4:34:e0 mscb->apfMsLwappLradNhMac = 78:da:6e:59:c9:8c mscb->apfMsLradSlotId = 0 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
*Dot1x_NW_MsgTask_0: May 09 11:44:52.087: 00:1b:77:b4:34:e0 mscb->apfMsBssid = 18:9c:5d:71:34:50 mscb->apfMsAddress = 00:1b:77:b4:34:e0 mscb->apfMsApVapId = 1
*Dot1x_NW_MsgTask_0: May 09 11:44:52.087: 00:1b:77:b4:34:e0 dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 0 mscb->apfMsLwappMwarInet.ipv4.addr = -1062679171
*Dot1x_NW_MsgTask_0: May 09 11:44:52.087: 00:1b:77:b4:34:e0 mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = -1062679163 mscb->apfMsLwappLradPort = 40089
*osapiBsnTimer: May 09 11:44:54.249: 00:1b:77:b4:34:e0 802.1x 'timeoutEvt' Timer expired for station 00:1b:77:b4:34:e0 and for message = M2
*dot1xMsgTask: May 09 11:44:54.249: 00:1b:77:b4:34:e0 Retransmit 1 of EAPOL-Key M1 (length 121) for mobile 00:1b:77:b4:34:e0
*dot1xMsgTask: May 09 11:44:54.249: 00:1b:77:b4:34:e0 mscb->apfMsLwappLradNhMac = 78:da:6e:59:c9:8c mscb->apfMsLradSlotId = 0 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
*dot1xMsgTask: May 09 11:44:54.249: 00:1b:77:b4:34:e0 mscb->apfMsBssid = 18:9c:5d:71:34:50 mscb->apfMsAddress = 00:1b:77:b4:34:e0 mscb->apfMsApVapId = 1
*dot1xMsgTask: May 09 11:44:54.249: 00:1b:77:b4:34:e0 dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 0 mscb->apfMsLwappMwarInet.ipv4.addr = -1062679171
*dot1xMsgTask: May 09 11:44:54.249: 00:1b:77:b4:34:e0 mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = -1062679163 mscb->apfMsLwappLradPort = 40089
*osapiBsnTimer: May 09 11:44:56.249: 00:1b:77:b4:34:e0 802.1x 'timeoutEvt' Timer expired for station 00:1b:77:b4:34:e0 and for message = M2
*dot1xMsgTask: May 09 11:44:56.249: 00:1b:77:b4:34:e0 Retransmit 2 of EAPOL-Key M1 (length 121) for mobile 00:1b:77:b4:34:e0
*dot1xMsgTask: May 09 11:44:56.249: 00:1b:77:b4:34:e0 mscb->apfMsLwappLradNhMac = 78:da:6e:59:c9:8c mscb->apfMsLradSlotId = 0 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
*dot1xMsgTask: May 09 11:44:56.249: 00:1b:77:b4:34:e0 mscb->apfMsBssid = 18:9c:5d:71:34:50 mscb->apfMsAddress = 00:1b:77:b4:34:e0 mscb->apfMsApVapId = 1
*dot1xMsgTask: May 09 11:44:56.249: 00:1b:77:b4:34:e0 dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 0 mscb->apfMsLwappMwarInet.ipv4.addr = -1062679171
*dot1xMsgTask: May 09 11:44:56.249: 00:1b:77:b4:34:e0 mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = -1062679163 mscb->apfMsLwappLradPort = 40089
*osapiBsnTimer: May 09 11:44:58.249: 00:1b:77:b4:34:e0 802.1x 'timeoutEvt' Timer expired for station 00:1b:77:b4:34:e0 and for message = M2
*dot1xMsgTask: May 09 11:44:58.249: 00:1b:77:b4:34:e0 Retransmit failure for EAPOL-Key M1 to mobile 00:1b:77:b4:34:e0, retransmit count 3, mscb deauth count 2
*dot1xMsgTask: May 09 11:44:58.249: 00:1b:77:b4:34:e0 Resetting MSCB PMK Cache Entry 0 for station 00:1b:77:b4:34:e0
*dot1xMsgTask: May 09 11:44:58.249: 00:1b:77:b4:34:e0 Removing BSSID 18:9c:5d:71:34:50 from PMKID cache of station 00:1b:77:b4:34:e0
*dot1xMsgTask: May 09 11:44:58.249: 00:1b:77:b4:34:e0 Setting active key cache index 0 ---> 8
*dot1xMsgTask: May 09 11:44:58.250: 00:1b:77:b4:34:e0 Sent Deauthenticate to mobile on BSSID 18:9c:5d:71:34:50 slot 0(caller 1x_ptsm.c:598)
*dot1xMsgTask: May 09 11:44:58.250: 00:1b:77:b4:34:e0 Setting active key cache index 8 ---> 8
*dot1xMsgTask: May 09 11:44:58.250: 00:1b:77:b4:34:e0 Deleting the PMK cache when de-authenticating the client.
*dot1xMsgTask: May 09 11:44:58.250: 00:1b:77:b4:34:e0 Global PMK Cache deletion failed.
*dot1xMsgTask: May 09 11:44:58.250: 00:1b:77:b4:34:e0 Scheduling deletion of Mobile Station: (callerId: 57) in 10 seconds
*dot1xMsgTask: May 09 11:44:58.250: 00:1b:77:b4:34:e0 Freeing EAP Retransmit Bufer for mobile 00:1b:77:b4:34:e0
*apfMsConnTask_4: May 09 11:45:03.768: 00:1b:77:b4:34:e0 Reassociation received from mobile on BSSID 18:9c:5d:71:34:50
*apfMsConnTask_4: May 09 11:45:03.768: 00:1b:77:b4:34:e0 Global 200 Clients are allowed to AP radio
*apfMsConnTask_4: May 09 11:45:03.769: 00:1b:77:b4:34:e0 Max Client Trap Threshold: 0 cur: 1
*apfMsConnTask_4: May 09 11:45:03.769: 00:1b:77:b4:34:e0 Rf profile 600 Clients are allowed to AP wlan
*apfMsConnTask_4: May 09 11:45:03.769: 00:1b:77:b4:34:e0 Applying Interface policy on Mobile, role Unassociated. Ms NAC State 2 Quarantine Vlan 0 Access Vlan 1
*apfMsConnTask_4: May 09 11:45:03.769: 00:1b:77:b4:34:e0 Re-applying interface policy for client
*apfMsConnTask_4: May 09 11:45:03.769: 00:1b:77:b4:34:e0 0.0.0.0 START (0) Changing IPv4 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2202)
*apfMsConnTask_4: May 09 11:45:03.769: 00:1b:77:b4:34:e0 0.0.0.0 START (0) Changing IPv6 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2223)
*apfMsConnTask_4: May 09 11:45:03.769: 00:1b:77:b4:34:e0 apfApplyWlanPolicy: Apply WLAN Policy over PMIPv6 Client Mobility Type
*apfMsConnTask_4: May 09 11:45:03.769: 00:1b:77:b4:34:e0 In processSsidIE:4795 setting Central switched to TRUE
*apfMsConnTask_4: May 09 11:45:03.769: 00:1b:77:b4:34:e0 In processSsidIE:4798 apVapId = 1 and Split Acl Id = 65535
*apfMsConnTask_4: May 09 11:45:03.769: 00:1b:77:b4:34:e0 Applying site-specific Local Bridging override for station 00:1b:77:b4:34:e0 - vapId 1, site 'default-group', interface 'catodos'
*apfMsConnTask_4: May 09 11:45:03.769: 00:1b:77:b4:34:e0 Applying Local Bridging Interface Policy for station 00:1b:77:b4:34:e0 - vlan 1, interface id 12, interface 'catodos'
*apfMsConnTask_4: May 09 11:45:03.769: 00:1b:77:b4:34:e0 processSsidIE statusCode is 0 and status is 0
*apfMsConnTask_4: May 09 11:45:03.769: 00:1b:77:b4:34:e0 processSsidIE ssid_done_flag is 0 finish_flag is 0
*apfMsConnTask_4: May 09 11:45:03.769: 00:1b:77:b4:34:e0 STA - rates (8): 2 4 11 22 12 18 24 36 48 72 96 108 0 0 0 0
*apfMsConnTask_4: May 09 11:45:03.769: 00:1b:77:b4:34:e0 suppRates statusCode is 0 and gotSuppRatesElement is 1
*apfMsConnTask_4: May 09 11:45:03.769: 00:1b:77:b4:34:e0 STA - rates (12): 2 4 11 22 12 18 24 36 48 72 96 108 0 0 0 0
*apfMsConnTask_4: May 09 11:45:03.769: 00:1b:77:b4:34:e0 extSuppRates statusCode is 0 and gotExtSuppRatesElement is 1
*apfMsConnTask_4: May 09 11:45:03.769: 00:1b:77:b4:34:e0 Processing RSN IE type 48, length 20 for mobile 00:1b:77:b4:34:e0
*apfMsConnTask_4: May 09 11:45:03.769: 00:1b:77:b4:34:e0 0.0.0.0 START (0) Initializing policy
*apfMsConnTask_4: May 09 11:45:03.769: 00:1b:77:b4:34:e0 0.0.0.0 START (0) Change state to AUTHCHECK (2) last state START (0)
*apfMsConnTask_4: May 09 11:45:03.769: 00:1b:77:b4:34:e0 0.0.0.0 AUTHCHECK (2) Change state to 8021X_REQD (3) last state AUTHCHECK (2)
*apfMsConnTask_4: May 09 11:45:03.769: 00:1b:77:b4:34:e0 Central switch is TRUE
*apfMsConnTask_4: May 09 11:45:03.769: 00:1b:77:b4:34:e0 Not Using WMM Compliance code qosCap 00
*apfMsConnTask_4: May 09 11:45:03.770: 00:1b:77:b4:34:e0 0.0.0.0 8021X_REQD (3) Plumbed mobile LWAPP rule on AP 18:9c:5d:71:34:50 vapId 1 apVapId 1 flex-acl-name:
*apfMsConnTask_4: May 09 11:45:03.770: 00:1b:77:b4:34:e0 apfPemAddUser2 (apf_policy.c:333) Changing state for mobile 00:1b:77:b4:34:e0 on AP 18:9c:5d:71:34:50 from Associated to Associated
*apfMsConnTask_4: May 09 11:45:03.770: 00:1b:77:b4:34:e0 apfPemAddUser2:session timeout forstation 00:1b:77:b4:34:e0 - Session Tout 1800, apfMsTimeOut '1800' and sessionTimerRunning flag is 0
*apfMsConnTask_4: May 09 11:45:03.770: 00:1b:77:b4:34:e0 Scheduling deletion of Mobile Station: (callerId: 49) in 1800 seconds
*apfMsConnTask_4: May 09 11:45:03.770: 00:1b:77:b4:34:e0 Func: apfPemAddUser2, Ms Timeout = 1800, Session Timeout = 1800
*apfMsConnTask_4: May 09 11:45:03.770: 00:1b:77:b4:34:e0 Sending Assoc Response to station on BSSID 18:9c:5d:71:34:50 (status 0) ApVapId 1 Slot 0
*apfMsConnTask_4: May 09 11:45:03.770: 00:1b:77:b4:34:e0 apfProcessAssocReq (apf_80211.c:8292) Changing state for mobile 00:1b:77:b4:34:e0 on AP 18:9c:5d:71:34:50 from Associated to Associated
*spamApTask6: May 09 11:45:03.772: 00:1b:77:b4:34:e0 Sent 1x initiate message to multi thread task for mobile 00:1b:77:b4:34:e0
*Dot1x_NW_MsgTask_0: May 09 11:45:03.773: 00:1b:77:b4:34:e0 Creating a PKC PMKID Cache entry for station 00:1b:77:b4:34:e0 (RSN 2)
*Dot1x_NW_MsgTask_0: May 09 11:45:03.773: 00:1b:77:b4:34:e0 Resetting MSCB PMK Cache Entry 0 for station 00:1b:77:b4:34:e0
*Dot1x_NW_MsgTask_0: May 09 11:45:03.773: 00:1b:77:b4:34:e0 Setting active key cache index 8 ---> 8
*Dot1x_NW_MsgTask_0: May 09 11:45:03.773: 00:1b:77:b4:34:e0 Setting active key cache index 8 ---> 0
*Dot1x_NW_MsgTask_0: May 09 11:45:03.773: 00:1b:77:b4:34:e0 Adding BSSID 18:9c:5d:71:34:50 to PMKID cache at index 0 for station 00:1b:77:b4:34:e0
*Dot1x_NW_MsgTask_0: May 09 11:45:03.773: New PMKID: (16)
*Dot1x_NW_MsgTask_0: May 09 11:45:03.773: [0000] f6 3d 52 9f 2a de 52 90 1d a2 46 49 0f 14 f6 69
*Dot1x_NW_MsgTask_0: May 09 11:45:03.773: 00:1b:77:b4:34:e0 Initiating RSN PSK to mobile 00:1b:77:b4:34:e0
*Dot1x_NW_MsgTask_0: May 09 11:45:03.773: 00:1b:77:b4:34:e0 EAP-PARAM Debug - eap-params for Wlan-Id :1 is disabled - applying Global eap timers and retries
*Dot1x_NW_MsgTask_0: May 09 11:45:03.773: 00:1b:77:b4:34:e0 dot1x - moving mobile 00:1b:77:b4:34:e0 into Force Auth state
*Dot1x_NW_MsgTask_0: May 09 11:45:03.773: 00:1b:77:b4:34:e0 EAPOL Header:
*Dot1x_NW_MsgTask_0: May 09 11:45:03.773: 00000000: 02 03 00 5f ..._
*Dot1x_NW_MsgTask_0: May 09 11:45:03.773: 00:1b:77:b4:34:e0 Found an cache entry for BSSID 18:9c:5d:71:34:50 in PMKID cache at index 0 of station 00:1b:77:b4:34:e0
*Dot1x_NW_MsgTask_0: May 09 11:45:03.773: 00:1b:77:b4:34:e0 Found an cache entry for BSSID 18:9c:5d:71:34:50 in PMKID cache at index 0 of station 00:1b:77:b4:34:e0
*Dot1x_NW_MsgTask_0: May 09 11:45:03.773: Including PMKID in M1 (16)
*Dot1x_NW_MsgTask_0: May 09 11:45:03.773: [0000] f6 3d 52 9f 2a de 52 90 1d a2 46 49 0f 14 f6 69
*Dot1x_NW_MsgTask_0: May 09 11:45:03.773: 00:1b:77:b4:34:e0 Starting key exchange to mobile 00:1b:77:b4:34:e0, data packets will be dropped
*Dot1x_NW_MsgTask_0: May 09 11:45:03.773: 00:1b:77:b4:34:e0 Sending EAPOL-Key Message to mobile 00:1b:77:b4:34:e0
state INITPMK (message 1), replay counter 00.00.00.00.00.00.00.00
*Dot1x_NW_MsgTask_0: May 09 11:45:03.773: 00:1b:77:b4:34:e0 Sending EAPOL-Key Message to mobile 00:1b:77:b4:34:e0
state INITPMK (message 1), replay counter 00.00.00.00.00.00.00.00
*Dot1x_NW_MsgTask_0: May 09 11:45:03.773: 00:1b:77:b4:34:e0 Allocating EAP Pkt for retransmission to mobile 00:1b:77:b4:34:e0
*Dot1x_NW_MsgTask_0: May 09 11:45:03.773: 00:1b:77:b4:34:e0 mscb->apfMsLwappLradNhMac = 78:da:6e:59:c9:8c mscb->apfMsLradSlotId = 0 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
*Dot1x_NW_MsgTask_0: May 09 11:45:03.773: 00:1b:77:b4:34:e0 mscb->apfMsBssid = 18:9c:5d:71:34:50 mscb->apfMsAddress = 00:1b:77:b4:34:e0 mscb->apfMsApVapId = 1
*Dot1x_NW_MsgTask_0: May 09 11:45:03.773: 00:1b:77:b4:34:e0 dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 0 mscb->apfMsLwappMwarInet.ipv4.addr = -1062679171
*Dot1x_NW_MsgTask_0: May 09 11:45:03.773: 00:1b:77:b4:34:e0 mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = -1062679163 mscb->apfMsLwappLradPort = 40089
*osapiBsnTimer: May 09 11:45:05.849: 00:1b:77:b4:34:e0 802.1x 'timeoutEvt' Timer expired for station 00:1b:77:b4:34:e0 and for message = M2
*dot1xMsgTask: May 09 11:45:05.849: 00:1b:77:b4:34:e0 Retransmit 1 of EAPOL-Key M1 (length 121) for mobile 00:1b:77:b4:34:e0
*dot1xMsgTask: May 09 11:45:05.849: 00:1b:77:b4:34:e0 mscb->apfMsLwappLradNhMac = 78:da:6e:59:c9:8c mscb->apfMsLradSlotId = 0 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
*dot1xMsgTask: May 09 11:45:05.849: 00:1b:77:b4:34:e0 mscb->apfMsBssid = 18:9c:5d:71:34:50 mscb->apfMsAddress = 00:1b:77:b4:34:e0 mscb->apfMsApVapId = 1
*dot1xMsgTask: May 09 11:45:05.849: 00:1b:77:b4:34:e0 dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 0 mscb->apfMsLwappMwarInet.ipv4.addr = -1062679171
*dot1xMsgTask: May 09 11:45:05.849: 00:1b:77:b4:34:e0 mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = -1062679163 mscb->apfMsLwappLradPort = 40089
*osapiBsnTimer: May 09 11:45:07.848: 00:1b:77:b4:34:e0 802.1x 'timeoutEvt' Timer expired for station 00:1b:77:b4:34:e0 and for message = M2
*dot1xMsgTask: May 09 11:45:07.849: 00:1b:77:b4:34:e0 Retransmit 2 of EAPOL-Key M1 (length 121) for mobile 00:1b:77:b4:34:e0
*dot1xMsgTask: May 09 11:45:07.849: 00:1b:77:b4:34:e0 mscb->apfMsLwappLradNhMac = 78:da:6e:59:c9:8c mscb->apfMsLradSlotId = 0 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
*dot1xMsgTask: May 09 11:45:07.849: 00:1b:77:b4:34:e0 mscb->apfMsBssid = 18:9c:5d:71:34:50 mscb->apfMsAddress = 00:1b:77:b4:34:e0 mscb->apfMsApVapId = 1
*dot1xMsgTask: May 09 11:45:07.849: 00:1b:77:b4:34:e0 dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 0 mscb->apfMsLwappMwarInet.ipv4.addr = -1062679171
*dot1xMsgTask: May 09 11:45:07.849: 00:1b:77:b4:34:e0 mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = -1062679163 mscb->apfMsLwappLradPort = 40089
*osapiBsnTimer: May 09 11:45:09.848: 00:1b:77:b4:34:e0 802.1x 'timeoutEvt' Timer expired for station 00:1b:77:b4:34:e0 and for message = M2
*dot1xMsgTask: May 09 11:45:09.849: 00:1b:77:b4:34:e0 Retransmit failure for EAPOL-Key M1 to mobile 00:1b:77:b4:34:e0, retransmit count 3, mscb deauth count 3
*dot1xMsgTask: May 09 11:45:09.849: 00:1b:77:b4:34:e0 Blacklisting (if enabled) mobile 00:1b:77:b4:34:e0
*dot1xMsgTask: May 09 11:45:09.849: 00:1b:77:b4:34:e0 0.0.0.0 8021X_REQD (3) Change state to START (0) last state 8021X_REQD (3)
*dot1xMsgTask: May 09 11:45:09.849: 00:1b:77:b4:34:e0 0.0.0.0 START (0) Reached FAILURE: from line 5274
*dot1xMsgTask: May 09 11:45:09.849: 00:1b:77:b4:34:e0 Scheduling deletion of Mobile Station: (callerId: 9) in 10 seconds
*apfMsConnTask_4: May 09 11:45:15.689: 00:1b:77:b4:34:e0 Reassociation received from mobile on BSSID 18:9c:5d:71:34:50
*apfMsConnTask_4: May 09 11:45:15.689: 00:1b:77:b4:34:e0 Global 200 Clients are allowed to AP radio
*apfMsConnTask_4: May 09 11:45:15.689: 00:1b:77:b4:34:e0 Max Client Trap Threshold: 0 cur: 1
*apfMsConnTask_4: May 09 11:45:15.689: 00:1b:77:b4:34:e0 Rf profile 600 Clients are allowed to AP wlan
*apfMsConnTask_4: May 09 11:45:15.689: 00:1b:77:b4:34:e0 Applying Interface policy on Mobile, role Unassociated. Ms NAC State 2 Quarantine Vlan 0 Access Vlan 1
*apfMsConnTask_4: May 09 11:45:15.689: 00:1b:77:b4:34:e0 Re-applying interface policy for client
*apfMsConnTask_4: May 09 11:45:15.689: 00:1b:77:b4:34:e0 0.0.0.0 START (0) Changing IPv4 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2202)
*apfMsConnTask_4: May 09 11:45:15.689: 00:1b:77:b4:34:e0 0.0.0.0 START (0) Changing IPv6 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2223)
*apfMsConnTask_4: May 09 11:45:15.689: 00:1b:77:b4:34:e0 apfApplyWlanPolicy: Apply WLAN Policy over PMIPv6 Client Mobility Type
*apfMsConnTask_4: May 09 11:45:15.689: 00:1b:77:b4:34:e0 In processSsidIE:4795 setting Central switched to TRUE
*apfMsConnTask_4: May 09 11:45:15.689: 00:1b:77:b4:34:e0 In processSsidIE:4798 apVapId = 1 and Split Acl Id = 65535
*apfMsConnTask_4: May 09 11:45:15.690: 00:1b:77:b4:34:e0 Applying site-specific Local Bridging override for station 00:1b:77:b4:34:e0 - vapId 1, site 'default-group', interface 'catodos'
*apfMsConnTask_4: May 09 11:45:15.690: 00:1b:77:b4:34:e0 Applying Local Bridging Interface Policy for station 00:1b:77:b4:34:e0 - vlan 1, interface id 12, interface 'catodos'
*apfMsConnTask_4: May 09 11:45:15.690: 00:1b:77:b4:34:e0 processSsidIE statusCode is 0 and status is 0
*apfMsConnTask_4: May 09 11:45:15.690: 00:1b:77:b4:34:e0 processSsidIE ssid_done_flag is 0 finish_flag is 0
*apfMsConnTask_4: May 09 11:45:15.690: 00:1b:77:b4:34:e0 STA - rates (8): 2 4 11 22 12 18 24 36 48 72 96 108 0 0 0 0
*apfMsConnTask_4: May 09 11:45:15.690: 00:1b:77:b4:34:e0 suppRates statusCode is 0 and gotSuppRatesElement is 1
*apfMsConnTask_4: May 09 11:45:15.690: 00:1b:77:b4:34:e0 STA - rates (12): 2 4 11 22 12 18 24 36 48 72 96 108 0 0 0 0
*apfMsConnTask_4: May 09 11:45:15.690: 00:1b:77:b4:34:e0 extSuppRates statusCode is 0 and gotExtSuppRatesElement is 1
*apfMsConnTask_4: May 09 11:45:15.690: 00:1b:77:b4:34:e0 Processing RSN IE type 48, length 20 for mobile 00:1b:77:b4:34:e0
*apfMsConnTask_4: May 09 11:45:15.690: 00:1b:77:b4:34:e0 0.0.0.0 START (0) Initializing policy
*apfMsConnTask_4: May 09 11:45:15.690: 00:1b:77:b4:34:e0 0.0.0.0 START (0) Change state to AUTHCHECK (2) last state START (0)
*apfMsConnTask_4: May 09 11:45:15.690: 00:1b:77:b4:34:e0 0.0.0.0 AUTHCHECK (2) Change state to 8021X_REQD (3) last state AUTHCHECK (2)
*apfMsConnTask_4: May 09 11:45:15.690: 00:1b:77:b4:34:e0 Central switch is TRUE
*apfMsConnTask_4: May 09 11:45:15.690: 00:1b:77:b4:34:e0 Not Using WMM Compliance code qosCap 00
*apfMsConnTask_4: May 09 11:45:15.690: 00:1b:77:b4:34:e0 0.0.0.0 8021X_REQD (3) Plumbed mobile LWAPP rule on AP 18:9c:5d:71:34:50 vapId 1 apVapId 1 flex-acl-name:
*apfMsConnTask_4: May 09 11:45:15.690: 00:1b:77:b4:34:e0 apfPemAddUser2 (apf_policy.c:333) Changing state for mobile 00:1b:77:b4:34:e0 on AP 18:9c:5d:71:34:50 from Associated to Associated
*apfMsConnTask_4: May 09 11:45:15.690: 00:1b:77:b4:34:e0 apfPemAddUser2:session timeout forstation 00:1b:77:b4:34:e0 - Session Tout 1800, apfMsTimeOut '1800' and sessionTimerRunning flag is 0
*apfMsConnTask_4: May 09 11:45:15.690: 00:1b:77:b4:34:e0 Scheduling deletion of Mobile Station: (callerId: 49) in 1800 seconds
*apfMsConnTask_4: May 09 11:45:15.690: 00:1b:77:b4:34:e0 Func: apfPemAddUser2, Ms Timeout = 1800, Session Timeout = 1800
*apfMsConnTask_4: May 09 11:45:15.690: 00:1b:77:b4:34:e0 Sending Assoc Response to station on BSSID 18:9c:5d:71:34:50 (status 0) ApVapId 1 Slot 0
*apfMsConnTask_4: May 09 11:45:15.691: 00:1b:77:b4:34:e0 apfProcessAssocReq (apf_80211.c:8292) Changing state for mobile 00:1b:77:b4:34:e0 on AP 18:9c:5d:71:34:50 from Associated to Associated
*spamApTask6: May 09 11:45:15.693: 00:1b:77:b4:34:e0 Sent 1x initiate message to multi thread task for mobile 00:1b:77:b4:34:e0
*Dot1x_NW_MsgTask_0: May 09 11:45:15.693: 00:1b:77:b4:34:e0 Creating a PKC PMKID Cache entry for station 00:1b:77:b4:34:e0 (RSN 2)
*Dot1x_NW_MsgTask_0: May 09 11:45:15.693: 00:1b:77:b4:34:e0 Resetting MSCB PMK Cache Entry 0 for station 00:1b:77:b4:34:e0
*Dot1x_NW_MsgTask_0: May 09 11:45:15.693: 00:1b:77:b4:34:e0 Removing BSSID 18:9c:5d:71:34:50 from PMKID cache of station 00:1b:77:b4:34:e0
*Dot1x_NW_MsgTask_0: May 09 11:45:15.693: 00:1b:77:b4:34:e0 Setting active key cache index 0 ---> 8
*Dot1x_NW_MsgTask_0: May 09 11:45:15.693: 00:1b:77:b4:34:e0 Setting active key cache index 8 ---> 0
*Dot1x_NW_MsgTask_0: May 09 11:45:15.693: 00:1b:77:b4:34:e0 Adding BSSID 18:9c:5d:71:34:50 to PMKID cache at index 0 for station 00:1b:77:b4:34:e0
*Dot1x_NW_MsgTask_0: May 09 11:45:15.693: New PMKID: (16)
*Dot1x_NW_MsgTask_0: May 09 11:45:15.693: [0000] f6 3d 52 9f 2a de 52 90 1d a2 46 49 0f 14 f6 69
*Dot1x_NW_MsgTask_0: May 09 11:45:15.693: 00:1b:77:b4:34:e0 Initiating RSN PSK to mobile 00:1b:77:b4:34:e0
*Dot1x_NW_MsgTask_0: May 09 11:45:15.693: 00:1b:77:b4:34:e0 EAP-PARAM Debug - eap-params for Wlan-Id :1 is disabled - applying Global eap timers and retries
*Dot1x_NW_MsgTask_0: May 09 11:45:15.693: 00:1b:77:b4:34:e0 dot1x - moving mobile 00:1b:77:b4:34:e0 into Force Auth state
*Dot1x_NW_MsgTask_0: May 09 11:45:15.693: 00:1b:77:b4:34:e0 EAPOL Header:
*Dot1x_NW_MsgTask_0: May 09 11:45:15.694: 00000000: 02 03 00 5f ..._
*Dot1x_NW_MsgTask_0: May 09 11:45:15.694: 00:1b:77:b4:34:e0 Found an cache entry for BSSID 18:9c:5d:71:34:50 in PMKID cache at index 0 of station 00:1b:77:b4:34:e0
*Dot1x_NW_MsgTask_0: May 09 11:45:15.694: 00:1b:77:b4:34:e0 Found an cache entry for BSSID 18:9c:5d:71:34:50 in PMKID cache at index 0 of station 00:1b:77:b4:34:e0
*Dot1x_NW_MsgTask_0: May 09 11:45:15.694: Including PMKID in M1 (16)
*Dot1x_NW_MsgTask_0: May 09 11:45:15.694: [0000] f6 3d 52 9f 2a de 52 90 1d a2 46 49 0f 14 f6 69
*Dot1x_NW_MsgTask_0: May 09 11:45:15.694: 00:1b:77:b4:34:e0 Starting key exchange to mobile 00:1b:77:b4:34:e0, data packets will be dropped
*Dot1x_NW_MsgTask_0: May 09 11:45:15.694: 00:1b:77:b4:34:e0 Sending EAPOL-Key Message to mobile 00:1b:77:b4:34:e0
state INITPMK (message 1), replay counter 00.00.00.00.00.00.00.00
*Dot1x_NW_MsgTask_0: May 09 11:45:15.694: 00:1b:77:b4:34:e0 Sending EAPOL-Key Message to mobile 00:1b:77:b4:34:e0
state INITPMK (message 1), replay counter 00.00.00.00.00.00.00.00
*Dot1x_NW_MsgTask_0: May 09 11:45:15.694: 00:1b:77:b4:34:e0 Reusing allocated memory for EAP Pkt for retransmission to mobile 00:1b:77:b4:34:e0
*Dot1x_NW_MsgTask_0: May 09 11:45:15.694: 00:1b:77:b4:34:e0 mscb->apfMsLwappLradNhMac = 78:da:6e:59:c9:8c mscb->apfMsLradSlotId = 0 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
*Dot1x_NW_MsgTask_0: May 09 11:45:15.694: 00:1b:77:b4:34:e0 mscb->apfMsBssid = 18:9c:5d:71:34:50 mscb->apfMsAddress = 00:1b:77:b4:34:e0 mscb->apfMsApVapId = 1
*Dot1x_NW_MsgTask_0: May 09 11:45:15.694: 00:1b:77:b4:34:e0 dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 0 mscb->apfMsLwappMwarInet.ipv4.addr = -1062679171
*Dot1x_NW_MsgTask_0: May 09 11:45:15.694: 00:1b:77:b4:34:e0 mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = -1062679163 mscb->apfMsLwappLradPort = 40089
*apfMsConnTask_4: May 09 11:45:15.875: 00:1b:77:b4:34:e0 Reassociation received from mobile on BSSID 18:9c:5d:71:34:50
*apfMsConnTask_4: May 09 11:45:15.875: 00:1b:77:b4:34:e0 Global 200 Clients are allowed to AP radio
*apfMsConnTask_4: May 09 11:45:15.875: 00:1b:77:b4:34:e0 Max Client Trap Threshold: 0 cur: 1
*apfMsConnTask_4: May 09 11:45:15.875: 00:1b:77:b4:34:e0 Rf profile 600 Clients are allowed to AP wlan
*apfMsConnTask_4: May 09 11:45:15.876: 00:1b:77:b4:34:e0 Applying Interface policy on Mobile, role Unassociated. Ms NAC State 2 Quarantine Vlan 0 Access Vlan 1
*apfMsConnTask_4: May 09 11:45:15.876: 00:1b:77:b4:34:e0 Re-applying interface policy for client
*apfMsConnTask_4: May 09 11:45:15.876: 00:1b:77:b4:34:e0 0.0.0.0 8021X_REQD (3) Changing IPv4 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2202)
*apfMsConnTask_4: May 09 11:45:15.876: 00:1b:77:b4:34:e0 0.0.0.0 8021X_REQD (3) Changing IPv6 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2223)
*apfMsConnTask_4: May 09 11:45:15.876: 00:1b:77:b4:34:e0 apfApplyWlanPolicy: Apply WLAN Policy over PMIPv6 Client Mobility Type
*apfMsConnTask_4: May 09 11:45:15.876: 00:1b:77:b4:34:e0 In processSsidIE:4795 setting Central switched to TRUE
*apfMsConnTask_4: May 09 11:45:15.876: 00:1b:77:b4:34:e0 In processSsidIE:4798 apVapId = 1 and Split Acl Id = 65535
*apfMsConnTask_4: May 09 11:45:15.876: 00:1b:77:b4:34:e0 Applying site-specific Local Bridging override for station 00:1b:77:b4:34:e0 - vapId 1, site 'default-group', interface 'catodos'
*apfMsConnTask_4: May 09 11:45:15.876: 00:1b:77:b4:34:e0 Applying Local Bridging Interface Policy for station 00:1b:77:b4:34:e0 - vlan 1, interface id 12, interface 'catodos'
*apfMsConnTask_4: May 09 11:45:15.876: 00:1b:77:b4:34:e0 processSsidIE statusCode is 0 and status is 0
*apfMsConnTask_4: May 09 11:45:15.876: 00:1b:77:b4:34:e0 processSsidIE ssid_done_flag is 0 finish_flag is 0
*apfMsConnTask_4: May 09 11:45:15.876: 00:1b:77:b4:34:e0 STA - rates (8): 2 4 11 22 12 18 24 36 48 72 96 108 0 0 0 0
*apfMsConnTask_4: May 09 11:45:15.876: 00:1b:77:b4:34:e0 suppRates statusCode is 0 and gotSuppRatesElement is 1
*apfMsConnTask_4: May 09 11:45:15.876: 00:1b:77:b4:34:e0 STA - rates (12): 2 4 11 22 12 18 24 36 48 72 96 108 0 0 0 0
*apfMsConnTask_4: May 09 11:45:15.876: 00:1b:77:b4:34:e0 extSuppRates statusCode is 0 and gotExtSuppRatesElement is 1
*apfMsConnTask_4: May 09 11:45:15.876: 00:1b:77:b4:34:e0 Processing RSN IE type 48, length 20 for mobile 00:1b:77:b4:34:e0
*apfMsConnTask_4: May 09 11:45:15.876: 00:1b:77:b4:34:e0 0.0.0.0 8021X_REQD (3) Initializing policy
*apfMsConnTask_4: May 09 11:45:15.876: 00:1b:77:b4:34:e0 0.0.0.0 8021X_REQD (3) Change state to AUTHCHECK (2) last state 8021X_REQD (3)
*apfMsConnTask_4: May 09 11:45:15.876: 00:1b:77:b4:34:e0 0.0.0.0 AUTHCHECK (2) Change state to 8021X_REQD (3) last state AUTHCHECK (2)
*apfMsConnTask_4: May 09 11:45:15.876: 00:1b:77:b4:34:e0 Central switch is TRUE
*apfMsConnTask_4: May 09 11:45:15.876: 00:1b:77:b4:34:e0 Not Using WMM Compliance code qosCap 00
*apfMsConnTask_4: May 09 11:45:15.876: 00:1b:77:b4:34:e0 0.0.0.0 8021X_REQD (3) Plumbed mobile LWAPP rule on AP 18:9c:5d:71:34:50 vapId 1 apVapId 1 flex-acl-name:
*apfMsConnTask_4: May 09 11:45:15.876: 00:1b:77:b4:34:e0 apfPemAddUser2 (apf_policy.c:333) Changing state for mobile 00:1b:77:b4:34:e0 on AP 18:9c:5d:71:34:50 from Associated to Associated
*apfMsConnTask_4: May 09 11:45:15.877: 00:1b:77:b4:34:e0 apfPemAddUser2:session timeout forstation 00:1b:77:b4:34:e0 - Session Tout 1800, apfMsTimeOut '1800' and sessionTimerRunning flag is 0
*apfMsConnTask_4: May 09 11:45:15.877: 00:1b:77:b4:34:e0 Scheduling deletion of Mobile Station: (callerId: 49) in 1800 seconds
*apfMsConnTask_4: May 09 11:45:15.877: 00:1b:77:b4:34:e0 Func: apfPemAddUser2, Ms Timeout = 1800, Session Timeout = 1800
*apfMsConnTask_4: May 09 11:45:15.877: 00:1b:77:b4:34:e0 Sending Assoc Response to station on BSSID 18:9c:5d:71:34:50 (status 0) ApVapId 1 Slot 0
*apfMsConnTask_4: May 09 11:45:15.877: 00:1b:77:b4:34:e0 apfProcessAssocReq (apf_80211.c:8292) Changing state for mobile 00:1b:77:b4:34:e0 on AP 18:9c:5d:71:34:50 from Associated to Associated
*spamApTask6: May 09 11:45:15.878: 00:1b:77:b4:34:e0 Sent 1x initiate message to multi thread task for mobile 00:1b:77:b4:34:e0
*Dot1x_NW_MsgTask_0: May 09 11:45:15.879: 00:1b:77:b4:34:e0 Creating a PKC PMKID Cache entry for station 00:1b:77:b4:34:e0 (RSN 2)
*Dot1x_NW_MsgTask_0: May 09 11:45:15.879: 00:1b:77:b4:34:e0 Resetting MSCB PMK Cache Entry 0 for station 00:1b:77:b4:34:e0
*Dot1x_NW_MsgTask_0: May 09 11:45:15.879: 00:1b:77:b4:34:e0 Removing BSSID 18:9c:5d:71:34:50 from PMKID cache of station 00:1b:77:b4:34:e0
*Dot1x_NW_MsgTask_0: May 09 11:45:15.879: 00:1b:77:b4:34:e0 Setting active key cache index 0 ---> 8
*Dot1x_NW_MsgTask_0: May 09 11:45:15.879: 00:1b:77:b4:34:e0 Setting active key cache index 8 ---> 0
*Dot1x_NW_MsgTask_0: May 09 11:45:15.879: 00:1b:77:b4:34:e0 Adding BSSID 18:9c:5d:71:34:50 to PMKID cache at index 0 for station 00:1b:77:b4:34:e0
*Dot1x_NW_MsgTask_0: May 09 11:45:15.879: New PMKID: (16)
*Dot1x_NW_MsgTask_0: May 09 11:45:15.879: [0000] f6 3d 52 9f 2a de 52 90 1d a2 46 49 0f 14 f6 69
*Dot1x_NW_MsgTask_0: May 09 11:45:15.879: 00:1b:77:b4:34:e0 Initiating RSN PSK to mobile 00:1b:77:b4:34:e0
*Dot1x_NW_MsgTask_0: May 09 11:45:15.879: 00:1b:77:b4:34:e0 EAP-PARAM Debug - eap-params for Wlan-Id :1 is disabled - applying Global eap timers and retries
*Dot1x_NW_MsgTask_0: May 09 11:45:15.879: 00:1b:77:b4:34:e0 dot1x - moving mobile 00:1b:77:b4:34:e0 into Force Auth state
*Dot1x_NW_MsgTask_0: May 09 11:45:15.879: 00:1b:77:b4:34:e0 EAPOL Header:
*Dot1x_NW_MsgTask_0: May 09 11:45:15.879: 00000000: 02 03 00 5f ..._
*Dot1x_NW_MsgTask_0: May 09 11:45:15.879: 00:1b:77:b4:34:e0 Found an cache entry for BSSID 18:9c:5d:71:34:50 in PMKID cache at index 0 of station 00:1b:77:b4:34:e0
*Dot1x_NW_MsgTask_0: May 09 11:45:15.879: 00:1b:77:b4:34:e0 Found an cache entry for BSSID 18:9c:5d:71:34:50 in PMKID cache at index 0 of station 00:1b:77:b4:34:e0
*Dot1x_NW_MsgTask_0: May 09 11:45:15.879: Including PMKID in M1 (16)
*Dot1x_NW_MsgTask_0: May 09 11:45:15.879: [0000] f6 3d 52 9f 2a de 52 90 1d a2 46 49 0f 14 f6 69
*Dot1x_NW_MsgTask_0: May 09 11:45:15.879: 00:1b:77:b4:34:e0 Starting key exchange to mobile 00:1b:77:b4:34:e0, data packets will be dropped
*Dot1x_NW_MsgTask_0: May 09 11:45:15.879: 00:1b:77:b4:34:e0 Sending EAPOL-Key Message to mobile 00:1b:77:b4:34:e0
state INITPMK (message 1), replay counter 00.00.00.00.00.00.00.00
*Dot1x_NW_MsgTask_0: May 09 11:45:15.879: 00:1b:77:b4:34:e0 Sending EAPOL-Key Message to mobile 00:1b:77:b4:34:e0
state INITPMK (message 1), replay counter 00.00.00.00.00.00.00.00
*Dot1x_NW_MsgTask_0: May 09 11:45:15.879: 00:1b:77:b4:34:e0 Reusing allocated memory for EAP Pkt for retransmission to mobile 00:1b:77:b4:34:e0
*Dot1x_NW_MsgTask_0: May 09 11:45:15.879: 00:1b:77:b4:34:e0 mscb->apfMsLwappLradNhMac = 78:da:6e:59:c9:8c mscb->apfMsLradSlotId = 0 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
*Dot1x_NW_MsgTask_0: May 09 11:45:15.879: 00:1b:77:b4:34:e0 mscb->apfMsBssid = 18:9c:5d:71:34:50 mscb->apfMsAddress = 00:1b:77:b4:34:e0 mscb->apfMsApVapId = 1
*Dot1x_NW_MsgTask_0: May 09 11:45:15.879: 00:1b:77:b4:34:e0 dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 0 mscb->apfMsLwappMwarInet.ipv4.addr = -1062679171
*Dot1x_NW_MsgTask_0: May 09 11:45:15.879: 00:1b:77:b4:34:e0 mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = -1062679163 mscb->apfMsLwappLradPort = 40089
*osapiBsnTimer: May 09 11:45:18.048: 00:1b:77:b4:34:e0 802.1x 'timeoutEvt' Timer expired for station 00:1b:77:b4:34:e0 and for message = M2
*dot1xMsgTask: May 09 11:45:18.049: 00:1b:77:b4:34:e0 Retransmit 1 of EAPOL-Key M1 (length 121) for mobile 00:1b:77:b4:34:e0
*dot1xMsgTask: May 09 11:45:18.049: 00:1b:77:b4:34:e0 mscb->apfMsLwappLradNhMac = 78:da:6e:59:c9:8c mscb->apfMsLradSlotId = 0 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
*dot1xMsgTask: May 09 11:45:18.049: 00:1b:77:b4:34:e0 mscb->apfMsBssid = 18:9c:5d:71:34:50 mscb->apfMsAddress = 00:1b:77:b4:34:e0 mscb->apfMsApVapId = 1
*dot1xMsgTask: May 09 11:45:18.049: 00:1b:77:b4:34:e0 dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 0 mscb->apfMsLwappMwarInet.ipv4.addr = -1062679171
*dot1xMsgTask: May 09 11:45:18.049: 00:1b:77:b4:34:e0 mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = -1062679163 mscb->apfMsLwappLradPort = 40089
*osapiBsnTimer: May 09 11:45:20.049: 00:1b:77:b4:34:e0 802.1x 'timeoutEvt' Timer expired for station 00:1b:77:b4:34:e0 and for message = M2
*dot1xMsgTask: May 09 11:45:20.049: 00:1b:77:b4:34:e0 Retransmit 2 of EAPOL-Key M1 (length 121) for mobile 00:1b:77:b4:34:e0
*dot1xMsgTask: May 09 11:45:20.049: 00:1b:77:b4:34:e0 mscb->apfMsLwappLradNhMac = 78:da:6e:59:c9:8c mscb->apfMsLradSlotId = 0 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
*dot1xMsgTask: May 09 11:45:20.049: 00:1b:77:b4:34:e0 mscb->apfMsBssid = 18:9c:5d:71:34:50 mscb->apfMsAddress = 00:1b:77:b4:34:e0 mscb->apfMsApVapId = 1
*dot1xMsgTask: May 09 11:45:20.049: 00:1b:77:b4:34:e0 dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 0 mscb->apfMsLwappMwarInet.ipv4.addr = -1062679171
*dot1xMsgTask: May 09 11:45:20.049: 00:1b:77:b4:34:e0 mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = -1062679163 mscb->apfMsLwappLradPort = 40089
*osapiBsnTimer: May 09 11:45:22.048: 00:1b:77:b4:34:e0 802.1x 'timeoutEvt' Timer expired for station 00:1b:77:b4:34:e0 and for message = M2
*dot1xMsgTask: May 09 11:45:22.049: 00:1b:77:b4:34:e0 Retransmit failure for EAPOL-Key M1 to mobile 00:1b:77:b4:34:e0, retransmit count 3, mscb deauth count 0
*dot1xMsgTask: May 09 11:45:22.049: 00:1b:77:b4:34:e0 Resetting MSCB PMK Cache Entry 0 for station 00:1b:77:b4:34:e0
*dot1xMsgTask: May 09 11:45:22.049: 00:1b:77:b4:34:e0 Removing BSSID 18:9c:5d:71:34:50 from PMKID cache of station 00:1b:77:b4:34:e0
*dot1xMsgTask: May 09 11:45:22.049: 00:1b:77:b4:34:e0 Setting active key cache index 0 ---> 8
*dot1xMsgTask: May 09 11:45:22.049: 00:1b:77:b4:34:e0 Sent Deauthenticate to mobile on BSSID 18:9c:5d:71:34:50 slot 0(caller 1x_ptsm.c:598)
*dot1xMsgTask: May 09 11:45:22.049: 00:1b:77:b4:34:e0 Setting active key cache index 8 ---> 8
*dot1xMsgTask: May 09 11:45:22.049: 00:1b:77:b4:34:e0 Deleting the PMK cache when de-authenticating the client.
*dot1xMsgTask: May 09 11:45:22.049: 00:1b:77:b4:34:e0 Global PMK Cache deletion failed.
*dot1xMsgTask: May 09 11:45:22.049: 00:1b:77:b4:34:e0 Scheduling deletion of Mobile Station: (callerId: 57) in 10 seconds
*dot1xMsgTask: May 09 11:45:22.049: 00:1b:77:b4:34:e0 Freeing EAP Retransmit Bufer for mobile 00:1b:77:b4:34:e0
*osapiBsnTimer: May 09 11:45:32.048: 00:1b:77:b4:34:e0 apfMsExpireCallback (apf_ms.c:625) Expiring Mobile!
*apfReceiveTask: May 09 11:45:32.049: 00:1b:77:b4:34:e0 apfMsExpireMobileStation (apf_ms.c:6632) Changing state for mobile 00:1b:77:b4:34:e0 on AP 18:9c:5d:71:34:50 from Associated to Disassociated
*apfReceiveTask: May 09 11:45:32.049: 00:1b:77:b4:34:e0 Scheduling deletion of Mobile Station: (callerId: 45) in 10 seconds
Thanks for any adviceIn some of the big name brands of wireless, there is "no such thing" as 802.11n on a 2.4 Ghz. No such thing because Cisco won't allow you (any more) to do channel bonding of 2.4 Ghz. It doesn't make any sense to bond an already restricted 2.4 Ghz non-overlapping channel (three) and squeeze this number down to two.
Can you check to ensure that the data rates for 802.11b are enabled? Maybe someone disabled data rates from 1 Mbps to 11 Mbps. -
Best practices for network design on WLC 2504 and 5508
Dear all:
I'm looking for some recommendations on WLC 2504 and 5508 about the the following:
Maximum amount of AP per port
The scenario when to use all ports in both WLC
Maximum number of clients(users) per port
Bandwidth comsumption of management vs data in order to assign one port for management
I've just found this:
Cisco 5508 controllers have eight Gigabit Ethernet distribution system ports, through which the controller can manage multiple access points. The 5508-12, 5508-25, 5508-50, 5508-100, and 5508-250 models allow a total of 12, 25, 50, 100, or 250 access points to join the controller. Cisco 5508 controllers have no restrictions on the number of access points per port. However, Cisco recommends using link aggregation (LAG) or configuring dynamic AP-manager interfaces on each Gigabit Ethernet port to automatically balance the load. If more than 100 access points are connected to the 5500 series controller, make sure that more than one gigabit Ethernet interface is connected to the upstream switch.
http://www.cisco.com/c/en/us/td/docs/wireless/controller/6-0/configuration/guide/Controller60CG/c60mint.html
Thanks for your help.The 5508-12, 5508-25, 5508-50, 5508-100, and 5508-250 models allow a total of 12, 25, 50, 100, or 250 access points to join the controller.
This is an old document. 5508 can now support up to 500 APs if you run firmware 7.X. 2504 can support up to 75 APs if you run firmware 7.4.X.
I'm looking for some recommendations on WLC 2504 and 5508 about the the following:
Best practice and recommendation is to LAG all ports so you will be able to form a link redundancy. If one link goes down, you have other link to push traffic. -
DEBUG-4-INVALID_MODULE on the WLC 2504 with version 7.6.100????
Hi!!! Please help with the solution.
I have one WLC 2504, 4 Cisco 1141 APs and one AP 1602.
Yesterday, I upgrade the WLC with version 7.5.102 to version 7.6.100.
After the upgrade in Message Logs on the WLC at the same time see the following message:
*RRM-MGR-5_0-GRP: Jan 23 08:44:25.449: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 08:35:41.189: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 08:34:17.373: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 08:25:32.125: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 08:24:09.309: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 08:15:23.013: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 08:14:01.213: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 08:05:13.949: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 08:03:53.149: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 07:55:04.905: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 07:53:45.086: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 07:44:55.813: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 07:43:37.010: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 07:34:46.749: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 07:33:28.930: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 07:24:37.669: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 07:23:20.865: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 07:14:28.593: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 07:13:12.789: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 07:04:19.529: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 07:03:04.729: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 06:54:10.493: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 06:52:56.689: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 06:44:01.445: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 06:42:48.645: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.
*sntpReceiveTask: Jan 23 06:35:22.218: #LOG-4-Q_IND: debug.c:2636 Unhandled debug module 5005.[...It occurred 19 times.!]
*RRM-MGR-2_4-GRP: Jan 23 06:33:48.070: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 06:32:36.266: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 06:23:39.030: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 06:22:28.226: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 06:13:29.986: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 06:12:20.186: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 06:03:20.930: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 06:02:12.130: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 05:53:11.890: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 05:52:04.090: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 05:43:02.838: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 05:41:56.039: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 05:32:53.790: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 05:31:47.986: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 05:22:44.758: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 05:21:39.950: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 05:12:35.718: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 05:11:31.910: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 05:02:26.670: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 05:01:23.859: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 04:52:17.606: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 04:51:15.794: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 04:42:08.566: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 04:41:07.750: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 04:31:59.506: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 04:30:59.703: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 04:21:50.450: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 04:20:51.646: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 04:11:41.402: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 04:10:43.598: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 04:01:32.326: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 04:00:35.522: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 03:51:23.258: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 03:50:27.442: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 03:41:14.182: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 03:40:19.378: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 03:31:05.106: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 03:30:11.302: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 03:20:56.042: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 03:20:03.242: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 03:10:46.978: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 03:09:55.178: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 03:00:37.902: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 02:59:47.102: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 02:50:28.826: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 02:49:39.026: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 02:40:19.782: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 02:39:30.983: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 02:30:10.742: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 02:29:22.942: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 02:20:01.698: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 02:19:14.886: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 02:09:52.646: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 02:09:06.842: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 01:59:43.587: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 01:58:58.783: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 01:49:34.546: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 01:48:50.742: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 01:39:25.494: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 01:38:42.687: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 01:29:16.454: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 01:28:34.642: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 01:19:07.402: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 01:18:26.594: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 01:08:58.362: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 01:08:18.554: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 00:58:49.322: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 00:58:10.514: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 00:48:40.266: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 00:48:02.467: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 00:38:31.222: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 00:37:54.411: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 00:28:22.174: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 00:27:46.374: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 00:18:13.106: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 00:17:38.306: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 00:08:04.062: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 00:07:30.262: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 22 23:57:55.022: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 22 23:57:22.222: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 22 23:47:45.958: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 22 23:47:14.158: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 22 23:37:36.906: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 22 23:37:06.106: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 22 23:27:27.826: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 22 23:26:58.026: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 22 23:17:18.762: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 22 23:16:49.962: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 22 23:07:09.686: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 22 23:06:41.870: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.
With what may be the problem exists? Any suggestion?Have you upgraded the FUS to 1.8.0.0? What happens if you try to boot from v7.5 do you see the messages and maybe boot back to v7.6?
Here is what the doc mentions about the error
Error Message %DEBUG-4-INVALID_MODULE: Unhandled debug module [dec].
Explanation This module cannot be debugged.
Recommended Action Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.
http://www.cisco.com/en/US/docs/wireless/controller/message/guide/msgs4.html#wp1000708
Sent from Cisco Technical Support iPhone App -
Hi Guys,
What configuration should I use in order to configure HA using 2x Cisco WLC 2504 ?
- Do I need to have licenses for 2x Controllers ? I have only one WLC with license installed.
At the moment I have the following scenario below.
AIR-CT2504-K9 – Primary (30 Aps Supported)
AIR-CT2504-HA-K9 – Secondary (0 license)
Software Version - 7.6.130.0 (Both Controllers)
Both controllers are going to be in the same place.
Can anyone help me please ?
Thanks,
EvertonThanks Scott Fella !
Just one more question.
Should I use a crossover cable to connect the primary controller to the secondary ? Or should I use a switch to connect them ?
Thanks,
Everton -
The customer have 1x WLC 2504 and 7x AP 3502i.
He are installing a automation system called Savant, this system use the Bonjour protocol to discovery the services on the network.
I've configured the multicast group on controller and switch (SG300) with IP 239.xxx.xxx.xxx, but the Savant (on iPad) don't finds the service.
Somebody has gone through a similar scenario?
I've used this document: http://www.cisco.com/en/US/products/hw/wireless/ps4570/products_tech_note09186a0080bb1d7c.shtml
PS: The customer haven't VLAN
Best regards.#Disable mdns/bonjour on wlc. place the WLC Management and AP vlan on same subnet. keep the savant server and iphone on same wlan and try.
#WLC 2500 supports only Multicast to Multicast for AP mode, be sure that wired side Multicast is configured properly and working.
#Try with any standard app to verify bonjour and AP mode multicast works.
#it is possible there may be any specific string that require to be added onto bonjour profile for savant to work. do debug mdns all enable and see what is missing.
it is suggested to open TAC case for troubleshooting. -
Install GoDaddy wildcard SSL on WLC 2504 conroller
I'm attempting to install a GoDaddy wildcard ssl certificate onto a WLC 2504 running version 7.4.100.0.
I am getting the error "#SSHPM-3-KEYED_PEM_DECODE_FAILED: sshpmcert.c:4055 Cannot PEM decode private key" when downloading the .pem file to the controller.
What I have attempted to do was to export the certificate from a Windows 2008 R2 server into a .pfx file. The file contained the private key and all possible root certficates (in this case a root and a intermediate cert). Now I took this .pfx file and attempted to create a .pem file with openssl using the following command: openssl pkcs12 -in myssl.pfx -out mynewssl.pem -passin pass:mypassword -passout pass:mypassword
Now I have opened the .pem file and verified it does contain the private key and the three certificates (wildcard, intermediate and root).Seth,
I had a similar problem, and saw the solution in another post on this forum. I am cross-posting this to help anyone else out there who might be searching for this answer.
Kudos to Robert Wells for finding this:
"I have it fixed now. The problem was the cisco only supports openssl 0.9.8x. I was using 1.0.1c. I used 0.9.8x and it worked perfectly fine."
The Windows version of OpenSSL I used was the 0.9.8y Light version from:
http://slproweb.com/download/Win32OpenSSL_Light-0_9_8y.exe
I hope this helps someone out there with this problem.
- Ken -
Query About Cisco WLC 2504 TDLS
Dear Friends,
One of my client want to encrypt data over the wireless. I have cisco WLC 2504 IOS Version 7.2.0.0.
Please help me on this. I think by-default data encrypt is enable. If not so how can I enable it. If I enable it is there any impact to my wireless user's.
Please help me out .....
Thanks & Regards,
Rahul WankhadeHow to enable:
http://www.cisco.com/c/en/us/support/docs/wireless/2500-series-wireless-controllers/113034-2500-deploy-guide-00.html#enable
Impact:
2500, WiSM2, WLC2—These platforms by default will not contain DTLS. To turn on data DTLS, you must install a license. These platforms will have a single image with data DTLS turned off. To use data DTLS you will need to have a license.
http://www.cisco.com/c/en/us/products/collateral/wireless/2500-series-wireless-controllers/data_sheet_c78-645111.html
AS per cisco: Encryption limits throughput at both the controller and the access point.
Regards
Dont forget to rate helpful posts -
LWAP 1231G can't join an WLC 2504 , Unsupported!!
Dear All,
I have WLC 2504 with 7.2.103.0 software version , & 2 different LWAP 1262n & 1231G with "c1200-rcvk9w8-mx.124-21a.JA" Image.
The 1262n is joined to the to the controller and working fine but the 1231G it cann't join the controller , the controller says "Join request received from an unsupported AP" !!
i will attaches the logs for this AP.
please can any one help.If you want to use 1230, then the "highest" WLC version you can run is the 7.0.235.3.
It says so in the Release Notes under the heading Software Release Support for Access Points, Table 1-1. -
I have two WLC 2504 controllers. These controllers are for two different buildings. But they share a VLAN, and network address range.
How can I control the access points to the register selected only at a specific controller.
Example:
AP 1 -> WLC 1
AP 2 -> WLC 2
AP 3 -> WLC 1
Since the buildings also broadcast in different SSID.
The two controllers are in a mobility group.I also ran into an install similar to yours. My client had a flat network and each wlc had licenses for the amount of APs in a particular building. What I did to make sure the APs never join the other wlc, is to use a Mac list. This allowed me to enter the APs base Mac address on the wlc and I enabled under the ap policy to verify authorization using Mac list. You can also do what AA mentioned which is good practice, but you have a chance that APs might join the other wlc. If the other wlc has different configurations, it might cause issues until the ap falls back to its primary.
Sent from Cisco Technical Support iPad App -
Compatible APs for Cisco WLC 2504
Is the cisco wlc 2504 compatible with the AIR-CAP-3602l and if so what firmware would i need to be running on the WLC ? My firm rushed out and bought a mesh solution without doing their homework
Hi Doug,
Data sheet for 3602 access point shows it support 2500 series WLC. Please refer to the link below.
http://www.cisco.com/en/US/prod/collateral/wireless/ps5678/ps11983/data_sheet_c78-686782.html
You may need firmware version above 7.2 to support 3602.
http://www.cisco.com/en/US/docs/wireless/controller/5500/tech_notes/Wireless_Software_Compatibility_Matrix.html
Hope that helps
Regards
Najaf
Please rate when applicable or helpful !!!
Maybe you are looking for
-
On 10.9 - I can no longer open, copy or preview files on a shared server
I am on a 2007 iMAC and I connect to a shared server in our office. I just upgraded to 10.9 and am experiencing a number of problems: - When trying to open files through finder I get the notification "Application not found" - When trying to copy to/
-
Hello, I haveing problem installing itunes on Windows 7. Erorr masage is "There is a problem with this Windows installer package. A program reguired for this install to comlet coudnt be run. Contact your support personnel or package vendor." Please h
-
Trouble Booting from External Drives; Trying to Defragment from External
I have a Verbatim External Firewire 400/USB 2.0 hard drive that has Leopard installed on it. I have installed Drive Genius and Disk Warrior on the external drive. I boot holding the Option key and see the list of drives, and the External does appear.
-
TV can not connect to Apple TV 1
Working fine then all of a sudden TV does not recognize Apple TV 1 Also light on Apple TV does not come on.
-
Javax.mail.MessagingException: Could not connect to SMTP host:
here is a part of my code import javax.mail.*; import javax.mail.internet.*; import java.util.*; public class Mail { /** Creates a new instance of PostMail */ public Mail() { public void postMail( String recipients[ ], String subject, String message