WLC 2504 v7.5.102.0 Client Association Issues. Association not consistent
Hi All,
I'm having a strange issue whereby client association to my corporate or guest wifi ssid are not consistent. Sometimes I have no issues connecting repeatedly and other times I cannot connect and receive the "Windows was unable to connect to *SSID*"
I'm unable to determine whether it is a wireless association issue or if its a authentication issue as I have troubles connecting to both my secure (WPA2, AES, 802.1x) corporate wifi or my guest (Open Auth) wifi.
Currently per day I have about 15 users using the wifi on both SSID's. The access points are right in the vicinity of the users. I have 2 LAP1142 access points on separate 802.11a/b/g/n channels and signal strenght is always high.. I'm certain its not co-channel interference or interference whatsoever. RSSI values are -60dBm and SNR 30+ dB. On average I will have 10 users on the wireless fine but one or two people are unable to connect.
I have had wireshark run and when it does not connect I do not see anything in the logs. No traffic is captured!
I cannot see the AAA capturing anything. Signal strength as stated above is high ( I have the AP on my desk!)
Sometimes I can instantly connect with no troubles and other times its not association at all. I've recently updated to version 7.5 and these issues started to occur. Previous version 7.3 had no problems at all for years!.
The logs in the WLC show
*Dot1x_NW_MsgTask_0: Nov 27 04:42:09.956: #DOT1X-3-INVALID_WPA_KEY_MSG_STATE: 1x_eapkey.c:864 Received invalid EAPOL-key M2 msg in START state - invalid secure bit; KeyLen 24, Key type 1, client 3c:a9:f4:4x:xx:xx
Does anyone have an idea what could this issue could be?
Many thanks
Thanks for your reply Sandeep. Been working on it all afternoon with debugging.
To answer your question, sometimes I can connect and sometimes I cannot. This afternoon I haven't been able to connect much at all. 2 out of 20 times perhaps. Other users I can see are connected to the two access points in this office. This isn't just happening on my laptop but several laptops. Same symptom.
Heres the dot1x output I have captured from the debug of a FAILED association attempt.
(Cisco Controller) >show debug
MAC Addr 1.................................. 3C:A9:F4:36:1C:48
Debug Flags Enabled:
dot1x aaa enabled.
dot1x packet enabled.
dot1x events enabled.
dot1x states enabled.
(Cisco Controller) >*DHCP Socket Task: Nov 27 07:44:49.842: 3c:a9:f4:36:1c:48 apfMsRunStateInc
*apfMsConnTask_4: Nov 27 07:45:15.284: 3c:a9:f4:36:1c:48 Processing RSN IE type 48, length 22 for mobile 3c:a9:f4:36:1c:48
*apfMsConnTask_4: Nov 27 07:45:15.284: 3c:a9:f4:36:1c:48 Received RSN IE with 0 PMKIDs from mobile 3c:a9:f4:36:1c:48
*apfMsConnTask_4: Nov 27 07:45:15.284: 3c:a9:f4:36:1c:48 Found an cache entry for BSSID 20:bb:c0:c9:26:92 in PMKID cache at index 0 of station 3c:a9:f4:36:1c:48
*apfMsConnTask_4: Nov 27 07:45:15.284: 3c:a9:f4:36:1c:48 Removing BSSID 20:bb:c0:c9:26:92 from PMKID cache of station 3c:a9:f4:36:1c:48
*apfMsConnTask_4: Nov 27 07:45:15.284: 3c:a9:f4:36:1c:48 Resetting MSCB PMK Cache Entry 0 for station 3c:a9:f4:36:1c:48
*apfMsConnTask_4: Nov 27 07:45:15.284: 3c:a9:f4:36:1c:48 Setting active key cache index 0 ---> 8
*apfMsConnTask_4: Nov 27 07:45:15.284: 3c:a9:f4:36:1c:48 unsetting PmkIdValidatedByAp
*apfMsConnTask_4: Nov 27 07:45:15.284: 3c:a9:f4:36:1c:48 apfMsRunStateDec
*apfMsConnTask_4: Nov 27 07:45:15.284: 3c:a9:f4:36:1c:48 apfMs1xStateDec
*dot1xMsgTask: Nov 27 07:45:15.287: 3c:a9:f4:36:1c:48 Disable re-auth, use PMK lifetime.
*dot1xMsgTask: Nov 27 07:45:15.288: 3c:a9:f4:36:1c:48 dot1x - moving mobile 3c:a9:f4:36:1c:48 into Connecting state
*dot1xMsgTask: Nov 27 07:45:15.288: 3c:a9:f4:36:1c:48 Sending EAP-Request/Identity to mobile 3c:a9:f4:36:1c:48 (EAP Id 1)
*dot1xMsgTask: Nov 27 07:45:15.288: 3c:a9:f4:36:1c:48 Sending 802.11 EAPOL message to mobile 3c:a9:f4:36:1c:48 WLAN 3, AP WLAN 3
*dot1xMsgTask: Nov 27 07:45:15.288: 00000000: 02 00 00 3c 01 01 00 3c 01 00 6e 65 74 77 6f 72 ...<...<..networ
*dot1xMsgTask: Nov 27 07:45:15.288: 00000010: 6b 69 64 3d 54 50 49 2d 57 49 46 49 2c 6e 61 73 kid=PI-WIFI,nas
*dot1xMsgTask: Nov 27 07:45:15.288: 00000020: 69 64 3d 4d 2d 54 50 49 2d 51 4c 44 2d 44 43 30 id=M-PI-QLD-DC0
*dot1xMsgTask: Nov 27 07:45:15.288: 00000030: 30 31 2d 57 43 30 31 2c 70 6f 72 74 69 64 3d 31 01-WC01,portid=1
*dot1xMsgTask: Nov 27 07:45:29.326: 3c:a9:f4:36:1c:48 Failure sending WPA EAPOL-Key due to invalid state 0 to mobile 3c:a9:f4:36:1c:48
*dot1xMsgTask: Nov 27 07:45:29.326: 3c:a9:f4:36:1c:48 Unable to send WPA key to mobile 3c:a9:f4:36:1c:48
(Cisco Controller) >*dot1xMsgTask: Nov 27 07:45:29.326: 3c:a9:f4:36:1c:48 Unable to update broadcast key to mobile 3C:A9:F4:36:1C:48
*osapiBsnTimer: Nov 27 07:45:45.126: 3c:a9:f4:36:1c:48 802.1x 'txWhen' Timer expired for station 3c:a9:f4:36:1c:48 and for message = M0
*dot1xMsgTask: Nov 27 07:45:45.126: 3c:a9:f4:36:1c:48 dot1x - moving mobile 3c:a9:f4:36:1c:48 into Connecting state
*dot1xMsgTask: Nov 27 07:45:45.126: 3c:a9:f4:36:1c:48 Sending EAP-Request/Identity to mobile 3c:a9:f4:36:1c:48 (EAP Id 2)
*dot1xMsgTask: Nov 27 07:45:45.126: 3c:a9:f4:36:1c:48 Sending 802.11 EAPOL message to mobile 3c:a9:f4:36:1c:48 WLAN 3, AP WLAN 3
*dot1xMsgTask: Nov 27 07:45:45.126: 00000000: 02 00 00 3c 01 02 00 3c 01 00 6e 65 74 77 6f 72 ...<...<..networ
*dot1xMsgTask: Nov 27 07:45:45.126: 00000010: 6b 69 64 3d 54 50 49 2d 57 49 46 49 2c 6e 61 73 kid=PI-WIFI,nas
*dot1xMsgTask: Nov 27 07:45:45.126: 00000020: 69 64 3d 4d 2d 54 50 49 2d 51 4c 44 2d 44 43 30 id=M-PI-QLD-DC0
I can see that the WLC has tried to send a EAP-Request/Identity request to the client but no response back. I just don't understand why it works at times and why it doesn't.
It has the same issues on my guest network which is open authentication. Nothing has changed in regards to configuration and it has been working for years. Only thing that changed was a version upgrade to 7.5 three weeks ago.
Here is the debug output of the client MAC when attempting to association to the GUEST network.
(Cisco Controller) >debug client 3C:A9:F4:36:1C:48
(Cisco Controller) >*apfProbeThread: Nov 27 07:53:48.059: aggregated probe IE: TIMESTAMP
*apfMsConnTask_4: Nov 27 07:58:02.021: 3c:a9:f4:36:1c:48 Adding mobile on LWAPP AP 20:bb:c0:c9:26:90(0)
*apfMsConnTask_4: Nov 27 07:58:02.021: 3c:a9:f4:36:1c:48 Association received from mobile on BSSID 20:bb:c0:c9:26:91
*apfMsConnTask_4: Nov 27 07:58:02.021: 3c:a9:f4:36:1c:48 Global 200 Clients are allowed to AP radio
*apfMsConnTask_4: Nov 27 07:58:02.021: 3c:a9:f4:36:1c:48 Max Client Trap Threshold: 0 cur: 5
*apfMsConnTask_4: Nov 27 07:58:02.021: 3c:a9:f4:36:1c:48 Rf profile 600 Clients are allowed to AP wlan
*apfMsConnTask_4: Nov 27 07:58:02.022: 3c:a9:f4:36:1c:48 Applying Interface policy on Mobile, role Unassociated. Ms NAC State 0 Quarantine Vlan 0 Access Vlan 0
*apfMsConnTask_4: Nov 27 07:58:02.022: 3c:a9:f4:36:1c:48 Re-applying interface policy for client
*apfMsConnTask_4: Nov 27 07:58:02.022: 3c:a9:f4:36:1c:48 0.0.0.0 START (0) Changing IPv4 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2164)
*apfMsConnTask_4: Nov 27 07:58:02.022: 3c:a9:f4:36:1c:48 0.0.0.0 START (0) Changing IPv6 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2185)
*apfMsConnTask_4: Nov 27 07:58:02.022: 3c:a9:f4:36:1c:48 apfApplyWlanPolicy: Apply WLAN Policy over PMIPv6 Client Mobility Type
*apfMsConnTask_4: Nov 27 07:58:02.022: 3c:a9:f4:36:1c:48 In processSsidIE:4565 setting Central switched to TRUE
*apfMsConnTask_4: Nov 27 07:58:02.022: 3c:a9:f4:36:1c:48 In processSsidIE:4568 apVapId = 2 and Split Acl Id = 65535
*apfMsConnTask_4: Nov 27 07:58:02.022: 3c:a9:f4:36:1c:48 Applying site-specific Local Bridging override for station 3c:a9:f4:36:1c:48 - vapId 2, site 'default-group', interface 'guest'
*apfMsConnTask_4: Nov 27 07:58:02.022: 3c:a9:f4:36:1c:48 Applying Local Bridging Interface Policy for station 3c:a9:f4:36:1c:48 - vlan 650, interface id 12, interface 'guest'
*apfMsConnTask_4: Nov 27 07:58:02.022: 3c:a9:f4:36:1c:48 processSsidIE statusCode is 0 and status is 0
*apfMsConnTask_4: Nov 27 07:58:02.022: 3c:a9:f4:36:1c:48 processSsidIE ssid_done_flag is 0 finish_flag is 0
*apfMsConnTask_4: Nov 27 07:58:02.022: 3c:a9:f4:36:1c:48 STA - rates (8): 130 132 139 150 12 18 24 36 0 0 0 0 0 0 0 0
*apfMsConnTask_4: Nov 27 07:58:02.022: 3c:a9:f4:36:1c:48 suppRates statusCode is 0 and gotSuppRatesElement is 1
*apfMsConnTask_4: Nov 27 07:58:02.022: 3c:a9:f4:36:1c:48 STA - rates (12): 130 132 139 150 12 18 24 36 48 72 96 108 0 0 0 0
*apfMsConnTask_4: Nov 27 07:58:02.022: 3c:a9:f4:36:1c:48 extSuppRates statusCode is 0 and gotExtSuppRatesElement is 1
*apfMsConnTask_4: Nov 27 07:58:02.022: 3c:a9:f4:36:1c:48 0.0.0.0 START (0) Initializing policy
*apfMsConnTask_4: Nov 27 07:58:02.022: 3c:a9:f4:36:1c:48 0.0.0.0 START (0) Change state to AUTHCHECK (2) last state START (0)
*apfMsConnTask_4: Nov 27 07:58:02.022: 3c:a9:f4:36:1c:48 0.0.0.0 AUTHCHECK (2) Change state to L2AUTHCOMPLETE (4) last state AUTHCHECK (2)
*apfMsConnTask_4: Nov 27 07:58:02.022: 3c:a9:f4:36:1c:48 Not Using WMM Compliance code qosCap 00
*apfMsConnTask_4: Nov 27 07:58:02.022: 3c:a9:f4:36:1c:48 0.0.0.0 L2AUTHCOMPLETE (4) Plumbed mobile LWAPP rule on AP 20:bb:c0:c9:26:90 vapId 2 apVapId 2 flex-acl-name:
*apfMsConnTask_4: Nov 27 07:58:02.022: 3c:a9:f4:36:1c:48 0.0.0.0 L2AUTHCOMPLETE (4) Change state to DHCP_REQD (7) last state L2AUTHCOMPLETE (4)
*apfMsConnTask_4: Nov 27 07:58:02.022: 3c:a9:f4:36:1c:48 apfMsAssoStateInc
*apfMsConnTask_4: Nov 27 07:58:02.022: 3c:a9:f4:36:1c:48 apfPemAddUser2 (apf_policy.c:333) Changing state for mobile 3c:a9:f4:36:1c:48 on AP 20:bb:c0:c9:26:90 from Idle to Associated
*apfMsConnTask_4: Nov 27 07:58:02.022: 3c:a9:f4:36:1c:48 apfPemAddUser2:session timeout forstation 3c:a9:f4:36:1c:48 - Session Tout 65535, apfMsTimeOut '65535' and sessionTimerRunning flag is 0
*apfMsConnTask_4: Nov 27 07:58:02.022: 3c:a9:f4:36:1c:48 Scheduling deletion of Mobile Station: (callerId: 49) in 65535 seconds
*apfMsConnTask_4: Nov 27 07:58:02.022: 3c:a9:f4:36:1c:48 Func: apfPemAddUser2, Ms Timeout = 65535, Session Timeout = 65535
*apfMsConnTask_4: Nov 27 07:58:02.023: 3c:a9:f4:36:1c:48 Sending Assoc Response to station on BSSID 20:bb:c0:c9:26:91 (status 0) ApVapId 2 Slot 0
*apfMsConnTask_4: Nov 27 07:58:02.023: 3c:a9:f4:36:1c:48 apfProcessAssocReq (apf_80211.c:7957) Changing state for mobile 3c:a9:f4:36:1c:48 on AP 20:bb:c0:c9:26:90 from Associated to Associated
*apfMsConnTask_4: Nov 27 07:58:02.026: 3c:a9:f4:36:1c:48 Updating AID for REAP AP Client 20:bb:c0:c9:26:90 - AID ===> 4
*apfReceiveTask: Nov 27 07:58:04.998: 3c:a9:f4:36:1c:48 0.0.0.0 DHCP_REQD (7) State Update from Mobility-Incomplete to Mobility-Complete, mobility role=Local, client state=APF_MS_STATE_ASSOCIATED
*apfReceiveTask: Nov 27 07:58:04.998: 3c:a9:f4:36:1c:48 0.0.0.0 DHCP_REQD (7) pemAdvanceState2 5716, Adding TMP rule
*apfReceiveTask: Nov 27 07:58:04.998: 3c:a9:f4:36:1c:48 0.0.0.0 DHCP_REQD (7) Adding Fast Path rule
type = Airespace AP - Learn IP address
on AP 20:bb:c0:c9:26:90, slot 0, interface = 1, QOS = 0
IPv4 ACL ID = 255, IPv
*apfReceiveTask: Nov 27 07:58:04.998: 3c:a9:f4:36:1c:48 0.0.0.0 DHCP_REQD (7) Fast Path rule (contd...) 802.1P = 0, DSCP = 0, TokenID = 15206 Local Bridging Vlan = 650, Local Bridging intf id = 12
*apfReceiveTask: Nov 27 07:58:04.998: 3c:a9:f4:36:1c:48 0.0.0.0 DHCP_REQD (7) Successfully plumbed mobile rule (IPv4 ACL ID 255, IPv6 ACL ID 255, L2 ACL ID 255)
*pemReceiveTask: Nov 27 07:58:04.999: 3c:a9:f4:36:1c:48 0.0.0.0 Added NPU entry of type 9, dtlFlags 0x0
*pemReceiveTask: Nov 27 07:58:04.999: 3c:a9:f4:36:1c:48 Sent an XID frame
*IPv6_Msg_Task: Nov 27 07:58:05.000: 3c:a9:f4:36:1c:48 Pushing IPv6 Vlan Intf ID 12: fe80:0000:0000:0000:f0a7:e03b:151a:3af8 , and MAC: 3C:A9:F4:36:1C:48 , Binding to Data Plane. SUCCESS !! dhcpv6bitmap 0
*IPv6_Msg_Task: Nov 27 07:58:05.000: 3c:a9:f4:36:1c:48 Link Local address fe80::f0a7:e03b:151a:3af8 updated to mscb. Not Advancing pem state.Current state: mscb in apfMsMmInitial mobility state and client state APF_MS_STATE_A
(Cisco Controller) >
Similar Messages
-
Cisco wlc ios 7.2 with clients windows 8 can not authenticate with 802.1x
Hello my name is Ivan:
I have a solution a unified solution wireless with a cisco wlc 7.2 and ap cisco. My issue is the follow:
My users are using laptops with OS windows 8, and they can not access to the network wireless because they authenticate in to the network using 802.1x wpa/wpa2 with tkip or aes.
I find a bug in the ios of the wlc. The number is CSCua29504. I would not to change the drivers in the laptop to join the users in to the solution.
Please is possible to find any software to do the upgrade in the wlc? Or perhaps we need to do an upgrade in to cisco lightweight access point?
Please help me in this issue.
Regards
IvanBug ID CSCua29504 has been fixed in WLC firmware 7.0.235.3, 7.3.101.X or 7.4.100.X.
So if you are NOT running any one of these codes, then yes. Upgrade your firmware is your solution.
Fixed in: (12)
7.4(100.0),7.4(1.20),7.3(112.0),7.3(101.0),7.3(1.67)
7.2(111.3),7.2(111.1),7.2(110.4),7.0(236.0),7.0(235.3) -
WLC 2504 - French characters for guest web login page
Good day,
I have recently installed a WLC 2504 and I have the following issue:
When I modify the text for the web login page (Under security/Web Auth/Web Auth page), if I use french caracters such as (é, è, à, etc...) in the message body, it does not show up correctly on users computers. As we're a bilingual country, I must put a bilingual text message. Are there any settings or workaround out there to rectify this?
We're on version 7.2.103.0
Thanks,
EricThanks Scott, I'll have a look at the documentation.
Right after sending this post, I tried typing the actual HTML code for the character instead and it seems to be working. I'm curious about custom webauth page, we may be able to customize it more than we thought we could do.
Cheers,
Eric -
Client got not connection to wlan over wlc 2504 on 802.11b/g
Hi everybody,
We are using a wlc 2504 with 7.6.100.0 and AP 1532e.
I have the strange observacion that only clients with 802.11n (2.4GHz) can connect to the WLAN. Clients thats works only with 802.11b/g, they can't connect to the WLAN. Affected are all machines which want to connect with 802.11b/g.
This is a MESH WLAN with 5GHz backhaul and 2.4GHz for the user.
During the debugging found the following:
*apfMsConnTask_4: May 09 11:44:40.581: 00:1b:77:b4:34:e0 Sending Assoc Response to station on BSSID 18:9c:5d:71:34:50 (status 0) ApVapId 1 Slot 0
*apfMsConnTask_4: May 09 11:44:40.581: 00:1b:77:b4:34:e0 apfProcessAssocReq (apf_80211.c:8292) Changing state for mobile 00:1b:77:b4:34:e0 on AP 18:9c:5d:71:34:50 from Associated to Associated
*spamApTask6: May 09 11:44:40.584: 00:1b:77:b4:34:e0 Sent 1x initiate message to multi thread task for mobile 00:1b:77:b4:34:e0
*Dot1x_NW_MsgTask_0: May 09 11:44:40.584: 00:1b:77:b4:34:e0 Creating a PKC PMKID Cache entry for station 00:1b:77:b4:34:e0 (RSN 2)
*Dot1x_NW_MsgTask_0: May 09 11:44:40.584: 00:1b:77:b4:34:e0 Resetting MSCB PMK Cache Entry 0 for station 00:1b:77:b4:34:e0
*Dot1x_NW_MsgTask_0: May 09 11:44:40.584: 00:1b:77:b4:34:e0 Setting active key cache index 8 ---> 8
*Dot1x_NW_MsgTask_0: May 09 11:44:40.584: 00:1b:77:b4:34:e0 Setting active key cache index 8 ---> 0
*Dot1x_NW_MsgTask_0: May 09 11:44:40.584: 00:1b:77:b4:34:e0 Adding BSSID 18:9c:5d:71:34:50 to PMKID cache at index 0 for station 00:1b:77:b4:34:e0
*Dot1x_NW_MsgTask_0: May 09 11:44:40.584: New PMKID: (16)
*Dot1x_NW_MsgTask_0: May 09 11:44:40.584: [0000] f6 3d 52 9f 2a de 52 90 1d a2 46 49 0f 14 f6 69
*Dot1x_NW_MsgTask_0: May 09 11:44:40.584: 00:1b:77:b4:34:e0 Initiating RSN PSK to mobile 00:1b:77:b4:34:e0
*Dot1x_NW_MsgTask_0: May 09 11:44:40.584: 00:1b:77:b4:34:e0 EAP-PARAM Debug - eap-params for Wlan-Id :1 is disabled - applying Global eap timers and retries
*Dot1x_NW_MsgTask_0: May 09 11:44:40.584: 00:1b:77:b4:34:e0 dot1x - moving mobile 00:1b:77:b4:34:e0 into Force Auth state
*Dot1x_NW_MsgTask_0: May 09 11:44:40.584: 00:1b:77:b4:34:e0 EAPOL Header:
*Dot1x_NW_MsgTask_0: May 09 11:44:40.584: 00000000: 02 03 00 5f ..._
*Dot1x_NW_MsgTask_0: May 09 11:44:40.584: 00:1b:77:b4:34:e0 Found an cache entry for BSSID 18:9c:5d:71:34:50 in PMKID cache at index 0 of station 00:1b:77:b4:34:e0
*Dot1x_NW_MsgTask_0: May 09 11:44:40.584: 00:1b:77:b4:34:e0 Found an cache entry for BSSID 18:9c:5d:71:34:50 in PMKID cache at index 0 of station 00:1b:77:b4:34:e0
*Dot1x_NW_MsgTask_0: May 09 11:44:40.584: Including PMKID in M1 (16)
*Dot1x_NW_MsgTask_0: May 09 11:44:40.584: [0000] f6 3d 52 9f 2a de 52 90 1d a2 46 49 0f 14 f6 69
*Dot1x_NW_MsgTask_0: May 09 11:44:40.584: 00:1b:77:b4:34:e0 Starting key exchange to mobile 00:1b:77:b4:34:e0, data packets will be dropped
*Dot1x_NW_MsgTask_0: May 09 11:44:40.584: 00:1b:77:b4:34:e0 Sending EAPOL-Key Message to mobile 00:1b:77:b4:34:e0
state INITPMK (message 1), replay counter 00.00.00.00.00.00.00.00
*Dot1x_NW_MsgTask_0: May 09 11:44:40.584: 00:1b:77:b4:34:e0 Sending EAPOL-Key Message to mobile 00:1b:77:b4:34:e0
state INITPMK (message 1), replay counter 00.00.00.00.00.00.00.00
*Dot1x_NW_MsgTask_0: May 09 11:44:40.584: 00:1b:77:b4:34:e0 Allocating EAP Pkt for retransmission to mobile 00:1b:77:b4:34:e0
*Dot1x_NW_MsgTask_0: May 09 11:44:40.585: 00:1b:77:b4:34:e0 mscb->apfMsLwappLradNhMac = 78:da:6e:59:c9:8c mscb->apfMsLradSlotId = 0 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
*Dot1x_NW_MsgTask_0: May 09 11:44:40.585: 00:1b:77:b4:34:e0 mscb->apfMsBssid = 18:9c:5d:71:34:50 mscb->apfMsAddress = 00:1b:77:b4:34:e0 mscb->apfMsApVapId = 1
*Dot1x_NW_MsgTask_0: May 09 11:44:40.585: 00:1b:77:b4:34:e0 dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 0 mscb->apfMsLwappMwarInet.ipv4.addr = -1062679171
*Dot1x_NW_MsgTask_0: May 09 11:44:40.585: 00:1b:77:b4:34:e0 mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = -1062679163 mscb->apfMsLwappLradPort = 40089
*osapiBsnTimer: May 09 11:44:42.649: 00:1b:77:b4:34:e0 802.1x 'timeoutEvt' Timer expired for station 00:1b:77:b4:34:e0 and for message = M2
*dot1xMsgTask: May 09 11:44:42.649: 00:1b:77:b4:34:e0 Retransmit 1 of EAPOL-Key M1 (length 121) for mobile 00:1b:77:b4:34:e0
*dot1xMsgTask: May 09 11:44:42.649: 00:1b:77:b4:34:e0 mscb->apfMsLwappLradNhMac = 78:da:6e:59:c9:8c mscb->apfMsLradSlotId = 0 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
*dot1xMsgTask: May 09 11:44:42.649: 00:1b:77:b4:34:e0 mscb->apfMsBssid = 18:9c:5d:71:34:50 mscb->apfMsAddress = 00:1b:77:b4:34:e0 mscb->apfMsApVapId = 1
*dot1xMsgTask: May 09 11:44:42.649: 00:1b:77:b4:34:e0 dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 0 mscb->apfMsLwappMwarInet.ipv4.addr = -1062679171
*dot1xMsgTask: May 09 11:44:42.649: 00:1b:77:b4:34:e0 mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = -1062679163 mscb->apfMsLwappLradPort = 40089
*osapiBsnTimer: May 09 11:44:44.649: 00:1b:77:b4:34:e0 802.1x 'timeoutEvt' Timer expired for station 00:1b:77:b4:34:e0 and for message = M2
*dot1xMsgTask: May 09 11:44:44.649: 00:1b:77:b4:34:e0 Retransmit 2 of EAPOL-Key M1 (length 121) for mobile 00:1b:77:b4:34:e0
*dot1xMsgTask: May 09 11:44:44.649: 00:1b:77:b4:34:e0 mscb->apfMsLwappLradNhMac = 78:da:6e:59:c9:8c mscb->apfMsLradSlotId = 0 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
*dot1xMsgTask: May 09 11:44:44.649: 00:1b:77:b4:34:e0 mscb->apfMsBssid = 18:9c:5d:71:34:50 mscb->apfMsAddress = 00:1b:77:b4:34:e0 mscb->apfMsApVapId = 1
*dot1xMsgTask: May 09 11:44:44.649: 00:1b:77:b4:34:e0 dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 0 mscb->apfMsLwappMwarInet.ipv4.addr = -1062679171
*dot1xMsgTask: May 09 11:44:44.650: 00:1b:77:b4:34:e0 mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = -1062679163 mscb->apfMsLwappLradPort = 40089
*osapiBsnTimer: May 09 11:44:46.649: 00:1b:77:b4:34:e0 802.1x 'timeoutEvt' Timer expired for station 00:1b:77:b4:34:e0 and for message = M2
*dot1xMsgTask: May 09 11:44:46.649: 00:1b:77:b4:34:e0 Retransmit failure for EAPOL-Key M1 to mobile 00:1b:77:b4:34:e0, retransmit count 3, mscb deauth count 1
*dot1xMsgTask: May 09 11:44:46.649: 00:1b:77:b4:34:e0 Resetting MSCB PMK Cache Entry 0 for station 00:1b:77:b4:34:e0
*dot1xMsgTask: May 09 11:44:46.649: 00:1b:77:b4:34:e0 Removing BSSID 18:9c:5d:71:34:50 from PMKID cache of station 00:1b:77:b4:34:e0
*dot1xMsgTask: May 09 11:44:46.649: 00:1b:77:b4:34:e0 Setting active key cache index 0 ---> 8
*dot1xMsgTask: May 09 11:44:46.649: 00:1b:77:b4:34:e0 Sent Deauthenticate to mobile on BSSID 18:9c:5d:71:34:50 slot 0(caller 1x_ptsm.c:598)
*dot1xMsgTask: May 09 11:44:46.649: 00:1b:77:b4:34:e0 Setting active key cache index 8 ---> 8
*dot1xMsgTask: May 09 11:44:46.649: 00:1b:77:b4:34:e0 Deleting the PMK cache when de-authenticating the client.
*dot1xMsgTask: May 09 11:44:46.649: 00:1b:77:b4:34:e0 Global PMK Cache deletion failed.
*dot1xMsgTask: May 09 11:44:46.649: 00:1b:77:b4:34:e0 Scheduling deletion of Mobile Station: (callerId: 57) in 10 seconds
*dot1xMsgTask: May 09 11:44:46.649: 00:1b:77:b4:34:e0 Freeing EAP Retransmit Bufer for mobile 00:1b:77:b4:34:e0
*apfMsConnTask_4: May 09 11:44:52.083: 00:1b:77:b4:34:e0 Reassociation received from mobile on BSSID 18:9c:5d:71:34:50
*apfMsConnTask_4: May 09 11:44:52.083: 00:1b:77:b4:34:e0 Global 200 Clients are allowed to AP radio
*apfMsConnTask_4: May 09 11:44:52.083: 00:1b:77:b4:34:e0 Max Client Trap Threshold: 0 cur: 1
*apfMsConnTask_4: May 09 11:44:52.083: 00:1b:77:b4:34:e0 Rf profile 600 Clients are allowed to AP wlan
*apfMsConnTask_4: May 09 11:44:52.083: 00:1b:77:b4:34:e0 Applying Interface policy on Mobile, role Unassociated. Ms NAC State 2 Quarantine Vlan 0 Access Vlan 1
*apfMsConnTask_4: May 09 11:44:52.083: 00:1b:77:b4:34:e0 Re-applying interface policy for client
*apfMsConnTask_4: May 09 11:44:52.083: 00:1b:77:b4:34:e0 0.0.0.0 START (0) Changing IPv4 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2202)
*apfMsConnTask_4: May 09 11:44:52.083: 00:1b:77:b4:34:e0 0.0.0.0 START (0) Changing IPv6 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2223)
*apfMsConnTask_4: May 09 11:44:52.083: 00:1b:77:b4:34:e0 apfApplyWlanPolicy: Apply WLAN Policy over PMIPv6 Client Mobility Type
*apfMsConnTask_4: May 09 11:44:52.083: 00:1b:77:b4:34:e0 In processSsidIE:4795 setting Central switched to TRUE
*apfMsConnTask_4: May 09 11:44:52.083: 00:1b:77:b4:34:e0 In processSsidIE:4798 apVapId = 1 and Split Acl Id = 65535
*apfMsConnTask_4: May 09 11:44:52.083: 00:1b:77:b4:34:e0 Applying site-specific Local Bridging override for station 00:1b:77:b4:34:e0 - vapId 1, site 'default-group', interface 'catodos'
*apfMsConnTask_4: May 09 11:44:52.083: 00:1b:77:b4:34:e0 Applying Local Bridging Interface Policy for station 00:1b:77:b4:34:e0 - vlan 1, interface id 12, interface 'catodos'
*apfMsConnTask_4: May 09 11:44:52.083: 00:1b:77:b4:34:e0 processSsidIE statusCode is 0 and status is 0
*apfMsConnTask_4: May 09 11:44:52.083: 00:1b:77:b4:34:e0 processSsidIE ssid_done_flag is 0 finish_flag is 0
*apfMsConnTask_4: May 09 11:44:52.083: 00:1b:77:b4:34:e0 STA - rates (8): 2 4 11 22 12 18 24 36 48 72 96 108 0 0 0 0
*apfMsConnTask_4: May 09 11:44:52.083: 00:1b:77:b4:34:e0 suppRates statusCode is 0 and gotSuppRatesElement is 1
*apfMsConnTask_4: May 09 11:44:52.083: 00:1b:77:b4:34:e0 STA - rates (12): 2 4 11 22 12 18 24 36 48 72 96 108 0 0 0 0
*apfMsConnTask_4: May 09 11:44:52.083: 00:1b:77:b4:34:e0 extSuppRates statusCode is 0 and gotExtSuppRatesElement is 1
*apfMsConnTask_4: May 09 11:44:52.083: 00:1b:77:b4:34:e0 Processing RSN IE type 48, length 20 for mobile 00:1b:77:b4:34:e0
*apfMsConnTask_4: May 09 11:44:52.083: 00:1b:77:b4:34:e0 0.0.0.0 START (0) Initializing policy
*apfMsConnTask_4: May 09 11:44:52.084: 00:1b:77:b4:34:e0 0.0.0.0 START (0) Change state to AUTHCHECK (2) last state START (0)
*apfMsConnTask_4: May 09 11:44:52.084: 00:1b:77:b4:34:e0 0.0.0.0 AUTHCHECK (2) Change state to 8021X_REQD (3) last state AUTHCHECK (2)
*apfMsConnTask_4: May 09 11:44:52.084: 00:1b:77:b4:34:e0 Central switch is TRUE
*apfMsConnTask_4: May 09 11:44:52.084: 00:1b:77:b4:34:e0 Not Using WMM Compliance code qosCap 00
*apfMsConnTask_4: May 09 11:44:52.084: 00:1b:77:b4:34:e0 0.0.0.0 8021X_REQD (3) Plumbed mobile LWAPP rule on AP 18:9c:5d:71:34:50 vapId 1 apVapId 1 flex-acl-name:
*apfMsConnTask_4: May 09 11:44:52.084: 00:1b:77:b4:34:e0 apfPemAddUser2 (apf_policy.c:333) Changing state for mobile 00:1b:77:b4:34:e0 on AP 18:9c:5d:71:34:50 from Associated to Associated
*apfMsConnTask_4: May 09 11:44:52.084: 00:1b:77:b4:34:e0 apfPemAddUser2:session timeout forstation 00:1b:77:b4:34:e0 - Session Tout 1800, apfMsTimeOut '1800' and sessionTimerRunning flag is 0
*apfMsConnTask_4: May 09 11:44:52.084: 00:1b:77:b4:34:e0 Scheduling deletion of Mobile Station: (callerId: 49) in 1800 seconds
*apfMsConnTask_4: May 09 11:44:52.084: 00:1b:77:b4:34:e0 Func: apfPemAddUser2, Ms Timeout = 1800, Session Timeout = 1800
*apfMsConnTask_4: May 09 11:44:52.084: 00:1b:77:b4:34:e0 Sending Assoc Response to station on BSSID 18:9c:5d:71:34:50 (status 0) ApVapId 1 Slot 0
*apfMsConnTask_4: May 09 11:44:52.084: 00:1b:77:b4:34:e0 apfProcessAssocReq (apf_80211.c:8292) Changing state for mobile 00:1b:77:b4:34:e0 on AP 18:9c:5d:71:34:50 from Associated to Associated
*spamApTask6: May 09 11:44:52.087: 00:1b:77:b4:34:e0 Sent 1x initiate message to multi thread task for mobile 00:1b:77:b4:34:e0
*Dot1x_NW_MsgTask_0: May 09 11:44:52.087: 00:1b:77:b4:34:e0 Creating a PKC PMKID Cache entry for station 00:1b:77:b4:34:e0 (RSN 2)
*Dot1x_NW_MsgTask_0: May 09 11:44:52.087: 00:1b:77:b4:34:e0 Resetting MSCB PMK Cache Entry 0 for station 00:1b:77:b4:34:e0
*Dot1x_NW_MsgTask_0: May 09 11:44:52.087: 00:1b:77:b4:34:e0 Setting active key cache index 8 ---> 8
*Dot1x_NW_MsgTask_0: May 09 11:44:52.087: 00:1b:77:b4:34:e0 Setting active key cache index 8 ---> 0
*Dot1x_NW_MsgTask_0: May 09 11:44:52.087: 00:1b:77:b4:34:e0 Adding BSSID 18:9c:5d:71:34:50 to PMKID cache at index 0 for station 00:1b:77:b4:34:e0
*Dot1x_NW_MsgTask_0: May 09 11:44:52.087: New PMKID: (16)
*Dot1x_NW_MsgTask_0: May 09 11:44:52.087: [0000] f6 3d 52 9f 2a de 52 90 1d a2 46 49 0f 14 f6 69
*Dot1x_NW_MsgTask_0: May 09 11:44:52.087: 00:1b:77:b4:34:e0 Initiating RSN PSK to mobile 00:1b:77:b4:34:e0
*Dot1x_NW_MsgTask_0: May 09 11:44:52.087: 00:1b:77:b4:34:e0 EAP-PARAM Debug - eap-params for Wlan-Id :1 is disabled - applying Global eap timers and retries
*Dot1x_NW_MsgTask_0: May 09 11:44:52.087: 00:1b:77:b4:34:e0 dot1x - moving mobile 00:1b:77:b4:34:e0 into Force Auth state
*Dot1x_NW_MsgTask_0: May 09 11:44:52.087: 00:1b:77:b4:34:e0 EAPOL Header:
*Dot1x_NW_MsgTask_0: May 09 11:44:52.087: 00000000: 02 03 00 5f ..._
*Dot1x_NW_MsgTask_0: May 09 11:44:52.087: 00:1b:77:b4:34:e0 Found an cache entry for BSSID 18:9c:5d:71:34:50 in PMKID cache at index 0 of station 00:1b:77:b4:34:e0
*Dot1x_NW_MsgTask_0: May 09 11:44:52.087: 00:1b:77:b4:34:e0 Found an cache entry for BSSID 18:9c:5d:71:34:50 in PMKID cache at index 0 of station 00:1b:77:b4:34:e0
*Dot1x_NW_MsgTask_0: May 09 11:44:52.087: Including PMKID in M1 (16)
*Dot1x_NW_MsgTask_0: May 09 11:44:52.087: [0000] f6 3d 52 9f 2a de 52 90 1d a2 46 49 0f 14 f6 69
*Dot1x_NW_MsgTask_0: May 09 11:44:52.087: 00:1b:77:b4:34:e0 Starting key exchange to mobile 00:1b:77:b4:34:e0, data packets will be dropped
*Dot1x_NW_MsgTask_0: May 09 11:44:52.087: 00:1b:77:b4:34:e0 Sending EAPOL-Key Message to mobile 00:1b:77:b4:34:e0
state INITPMK (message 1), replay counter 00.00.00.00.00.00.00.00
*Dot1x_NW_MsgTask_0: May 09 11:44:52.087: 00:1b:77:b4:34:e0 Sending EAPOL-Key Message to mobile 00:1b:77:b4:34:e0
state INITPMK (message 1), replay counter 00.00.00.00.00.00.00.00
*Dot1x_NW_MsgTask_0: May 09 11:44:52.087: 00:1b:77:b4:34:e0 Allocating EAP Pkt for retransmission to mobile 00:1b:77:b4:34:e0
*Dot1x_NW_MsgTask_0: May 09 11:44:52.087: 00:1b:77:b4:34:e0 mscb->apfMsLwappLradNhMac = 78:da:6e:59:c9:8c mscb->apfMsLradSlotId = 0 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
*Dot1x_NW_MsgTask_0: May 09 11:44:52.087: 00:1b:77:b4:34:e0 mscb->apfMsBssid = 18:9c:5d:71:34:50 mscb->apfMsAddress = 00:1b:77:b4:34:e0 mscb->apfMsApVapId = 1
*Dot1x_NW_MsgTask_0: May 09 11:44:52.087: 00:1b:77:b4:34:e0 dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 0 mscb->apfMsLwappMwarInet.ipv4.addr = -1062679171
*Dot1x_NW_MsgTask_0: May 09 11:44:52.087: 00:1b:77:b4:34:e0 mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = -1062679163 mscb->apfMsLwappLradPort = 40089
*osapiBsnTimer: May 09 11:44:54.249: 00:1b:77:b4:34:e0 802.1x 'timeoutEvt' Timer expired for station 00:1b:77:b4:34:e0 and for message = M2
*dot1xMsgTask: May 09 11:44:54.249: 00:1b:77:b4:34:e0 Retransmit 1 of EAPOL-Key M1 (length 121) for mobile 00:1b:77:b4:34:e0
*dot1xMsgTask: May 09 11:44:54.249: 00:1b:77:b4:34:e0 mscb->apfMsLwappLradNhMac = 78:da:6e:59:c9:8c mscb->apfMsLradSlotId = 0 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
*dot1xMsgTask: May 09 11:44:54.249: 00:1b:77:b4:34:e0 mscb->apfMsBssid = 18:9c:5d:71:34:50 mscb->apfMsAddress = 00:1b:77:b4:34:e0 mscb->apfMsApVapId = 1
*dot1xMsgTask: May 09 11:44:54.249: 00:1b:77:b4:34:e0 dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 0 mscb->apfMsLwappMwarInet.ipv4.addr = -1062679171
*dot1xMsgTask: May 09 11:44:54.249: 00:1b:77:b4:34:e0 mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = -1062679163 mscb->apfMsLwappLradPort = 40089
*osapiBsnTimer: May 09 11:44:56.249: 00:1b:77:b4:34:e0 802.1x 'timeoutEvt' Timer expired for station 00:1b:77:b4:34:e0 and for message = M2
*dot1xMsgTask: May 09 11:44:56.249: 00:1b:77:b4:34:e0 Retransmit 2 of EAPOL-Key M1 (length 121) for mobile 00:1b:77:b4:34:e0
*dot1xMsgTask: May 09 11:44:56.249: 00:1b:77:b4:34:e0 mscb->apfMsLwappLradNhMac = 78:da:6e:59:c9:8c mscb->apfMsLradSlotId = 0 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
*dot1xMsgTask: May 09 11:44:56.249: 00:1b:77:b4:34:e0 mscb->apfMsBssid = 18:9c:5d:71:34:50 mscb->apfMsAddress = 00:1b:77:b4:34:e0 mscb->apfMsApVapId = 1
*dot1xMsgTask: May 09 11:44:56.249: 00:1b:77:b4:34:e0 dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 0 mscb->apfMsLwappMwarInet.ipv4.addr = -1062679171
*dot1xMsgTask: May 09 11:44:56.249: 00:1b:77:b4:34:e0 mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = -1062679163 mscb->apfMsLwappLradPort = 40089
*osapiBsnTimer: May 09 11:44:58.249: 00:1b:77:b4:34:e0 802.1x 'timeoutEvt' Timer expired for station 00:1b:77:b4:34:e0 and for message = M2
*dot1xMsgTask: May 09 11:44:58.249: 00:1b:77:b4:34:e0 Retransmit failure for EAPOL-Key M1 to mobile 00:1b:77:b4:34:e0, retransmit count 3, mscb deauth count 2
*dot1xMsgTask: May 09 11:44:58.249: 00:1b:77:b4:34:e0 Resetting MSCB PMK Cache Entry 0 for station 00:1b:77:b4:34:e0
*dot1xMsgTask: May 09 11:44:58.249: 00:1b:77:b4:34:e0 Removing BSSID 18:9c:5d:71:34:50 from PMKID cache of station 00:1b:77:b4:34:e0
*dot1xMsgTask: May 09 11:44:58.249: 00:1b:77:b4:34:e0 Setting active key cache index 0 ---> 8
*dot1xMsgTask: May 09 11:44:58.250: 00:1b:77:b4:34:e0 Sent Deauthenticate to mobile on BSSID 18:9c:5d:71:34:50 slot 0(caller 1x_ptsm.c:598)
*dot1xMsgTask: May 09 11:44:58.250: 00:1b:77:b4:34:e0 Setting active key cache index 8 ---> 8
*dot1xMsgTask: May 09 11:44:58.250: 00:1b:77:b4:34:e0 Deleting the PMK cache when de-authenticating the client.
*dot1xMsgTask: May 09 11:44:58.250: 00:1b:77:b4:34:e0 Global PMK Cache deletion failed.
*dot1xMsgTask: May 09 11:44:58.250: 00:1b:77:b4:34:e0 Scheduling deletion of Mobile Station: (callerId: 57) in 10 seconds
*dot1xMsgTask: May 09 11:44:58.250: 00:1b:77:b4:34:e0 Freeing EAP Retransmit Bufer for mobile 00:1b:77:b4:34:e0
*apfMsConnTask_4: May 09 11:45:03.768: 00:1b:77:b4:34:e0 Reassociation received from mobile on BSSID 18:9c:5d:71:34:50
*apfMsConnTask_4: May 09 11:45:03.768: 00:1b:77:b4:34:e0 Global 200 Clients are allowed to AP radio
*apfMsConnTask_4: May 09 11:45:03.769: 00:1b:77:b4:34:e0 Max Client Trap Threshold: 0 cur: 1
*apfMsConnTask_4: May 09 11:45:03.769: 00:1b:77:b4:34:e0 Rf profile 600 Clients are allowed to AP wlan
*apfMsConnTask_4: May 09 11:45:03.769: 00:1b:77:b4:34:e0 Applying Interface policy on Mobile, role Unassociated. Ms NAC State 2 Quarantine Vlan 0 Access Vlan 1
*apfMsConnTask_4: May 09 11:45:03.769: 00:1b:77:b4:34:e0 Re-applying interface policy for client
*apfMsConnTask_4: May 09 11:45:03.769: 00:1b:77:b4:34:e0 0.0.0.0 START (0) Changing IPv4 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2202)
*apfMsConnTask_4: May 09 11:45:03.769: 00:1b:77:b4:34:e0 0.0.0.0 START (0) Changing IPv6 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2223)
*apfMsConnTask_4: May 09 11:45:03.769: 00:1b:77:b4:34:e0 apfApplyWlanPolicy: Apply WLAN Policy over PMIPv6 Client Mobility Type
*apfMsConnTask_4: May 09 11:45:03.769: 00:1b:77:b4:34:e0 In processSsidIE:4795 setting Central switched to TRUE
*apfMsConnTask_4: May 09 11:45:03.769: 00:1b:77:b4:34:e0 In processSsidIE:4798 apVapId = 1 and Split Acl Id = 65535
*apfMsConnTask_4: May 09 11:45:03.769: 00:1b:77:b4:34:e0 Applying site-specific Local Bridging override for station 00:1b:77:b4:34:e0 - vapId 1, site 'default-group', interface 'catodos'
*apfMsConnTask_4: May 09 11:45:03.769: 00:1b:77:b4:34:e0 Applying Local Bridging Interface Policy for station 00:1b:77:b4:34:e0 - vlan 1, interface id 12, interface 'catodos'
*apfMsConnTask_4: May 09 11:45:03.769: 00:1b:77:b4:34:e0 processSsidIE statusCode is 0 and status is 0
*apfMsConnTask_4: May 09 11:45:03.769: 00:1b:77:b4:34:e0 processSsidIE ssid_done_flag is 0 finish_flag is 0
*apfMsConnTask_4: May 09 11:45:03.769: 00:1b:77:b4:34:e0 STA - rates (8): 2 4 11 22 12 18 24 36 48 72 96 108 0 0 0 0
*apfMsConnTask_4: May 09 11:45:03.769: 00:1b:77:b4:34:e0 suppRates statusCode is 0 and gotSuppRatesElement is 1
*apfMsConnTask_4: May 09 11:45:03.769: 00:1b:77:b4:34:e0 STA - rates (12): 2 4 11 22 12 18 24 36 48 72 96 108 0 0 0 0
*apfMsConnTask_4: May 09 11:45:03.769: 00:1b:77:b4:34:e0 extSuppRates statusCode is 0 and gotExtSuppRatesElement is 1
*apfMsConnTask_4: May 09 11:45:03.769: 00:1b:77:b4:34:e0 Processing RSN IE type 48, length 20 for mobile 00:1b:77:b4:34:e0
*apfMsConnTask_4: May 09 11:45:03.769: 00:1b:77:b4:34:e0 0.0.0.0 START (0) Initializing policy
*apfMsConnTask_4: May 09 11:45:03.769: 00:1b:77:b4:34:e0 0.0.0.0 START (0) Change state to AUTHCHECK (2) last state START (0)
*apfMsConnTask_4: May 09 11:45:03.769: 00:1b:77:b4:34:e0 0.0.0.0 AUTHCHECK (2) Change state to 8021X_REQD (3) last state AUTHCHECK (2)
*apfMsConnTask_4: May 09 11:45:03.769: 00:1b:77:b4:34:e0 Central switch is TRUE
*apfMsConnTask_4: May 09 11:45:03.769: 00:1b:77:b4:34:e0 Not Using WMM Compliance code qosCap 00
*apfMsConnTask_4: May 09 11:45:03.770: 00:1b:77:b4:34:e0 0.0.0.0 8021X_REQD (3) Plumbed mobile LWAPP rule on AP 18:9c:5d:71:34:50 vapId 1 apVapId 1 flex-acl-name:
*apfMsConnTask_4: May 09 11:45:03.770: 00:1b:77:b4:34:e0 apfPemAddUser2 (apf_policy.c:333) Changing state for mobile 00:1b:77:b4:34:e0 on AP 18:9c:5d:71:34:50 from Associated to Associated
*apfMsConnTask_4: May 09 11:45:03.770: 00:1b:77:b4:34:e0 apfPemAddUser2:session timeout forstation 00:1b:77:b4:34:e0 - Session Tout 1800, apfMsTimeOut '1800' and sessionTimerRunning flag is 0
*apfMsConnTask_4: May 09 11:45:03.770: 00:1b:77:b4:34:e0 Scheduling deletion of Mobile Station: (callerId: 49) in 1800 seconds
*apfMsConnTask_4: May 09 11:45:03.770: 00:1b:77:b4:34:e0 Func: apfPemAddUser2, Ms Timeout = 1800, Session Timeout = 1800
*apfMsConnTask_4: May 09 11:45:03.770: 00:1b:77:b4:34:e0 Sending Assoc Response to station on BSSID 18:9c:5d:71:34:50 (status 0) ApVapId 1 Slot 0
*apfMsConnTask_4: May 09 11:45:03.770: 00:1b:77:b4:34:e0 apfProcessAssocReq (apf_80211.c:8292) Changing state for mobile 00:1b:77:b4:34:e0 on AP 18:9c:5d:71:34:50 from Associated to Associated
*spamApTask6: May 09 11:45:03.772: 00:1b:77:b4:34:e0 Sent 1x initiate message to multi thread task for mobile 00:1b:77:b4:34:e0
*Dot1x_NW_MsgTask_0: May 09 11:45:03.773: 00:1b:77:b4:34:e0 Creating a PKC PMKID Cache entry for station 00:1b:77:b4:34:e0 (RSN 2)
*Dot1x_NW_MsgTask_0: May 09 11:45:03.773: 00:1b:77:b4:34:e0 Resetting MSCB PMK Cache Entry 0 for station 00:1b:77:b4:34:e0
*Dot1x_NW_MsgTask_0: May 09 11:45:03.773: 00:1b:77:b4:34:e0 Setting active key cache index 8 ---> 8
*Dot1x_NW_MsgTask_0: May 09 11:45:03.773: 00:1b:77:b4:34:e0 Setting active key cache index 8 ---> 0
*Dot1x_NW_MsgTask_0: May 09 11:45:03.773: 00:1b:77:b4:34:e0 Adding BSSID 18:9c:5d:71:34:50 to PMKID cache at index 0 for station 00:1b:77:b4:34:e0
*Dot1x_NW_MsgTask_0: May 09 11:45:03.773: New PMKID: (16)
*Dot1x_NW_MsgTask_0: May 09 11:45:03.773: [0000] f6 3d 52 9f 2a de 52 90 1d a2 46 49 0f 14 f6 69
*Dot1x_NW_MsgTask_0: May 09 11:45:03.773: 00:1b:77:b4:34:e0 Initiating RSN PSK to mobile 00:1b:77:b4:34:e0
*Dot1x_NW_MsgTask_0: May 09 11:45:03.773: 00:1b:77:b4:34:e0 EAP-PARAM Debug - eap-params for Wlan-Id :1 is disabled - applying Global eap timers and retries
*Dot1x_NW_MsgTask_0: May 09 11:45:03.773: 00:1b:77:b4:34:e0 dot1x - moving mobile 00:1b:77:b4:34:e0 into Force Auth state
*Dot1x_NW_MsgTask_0: May 09 11:45:03.773: 00:1b:77:b4:34:e0 EAPOL Header:
*Dot1x_NW_MsgTask_0: May 09 11:45:03.773: 00000000: 02 03 00 5f ..._
*Dot1x_NW_MsgTask_0: May 09 11:45:03.773: 00:1b:77:b4:34:e0 Found an cache entry for BSSID 18:9c:5d:71:34:50 in PMKID cache at index 0 of station 00:1b:77:b4:34:e0
*Dot1x_NW_MsgTask_0: May 09 11:45:03.773: 00:1b:77:b4:34:e0 Found an cache entry for BSSID 18:9c:5d:71:34:50 in PMKID cache at index 0 of station 00:1b:77:b4:34:e0
*Dot1x_NW_MsgTask_0: May 09 11:45:03.773: Including PMKID in M1 (16)
*Dot1x_NW_MsgTask_0: May 09 11:45:03.773: [0000] f6 3d 52 9f 2a de 52 90 1d a2 46 49 0f 14 f6 69
*Dot1x_NW_MsgTask_0: May 09 11:45:03.773: 00:1b:77:b4:34:e0 Starting key exchange to mobile 00:1b:77:b4:34:e0, data packets will be dropped
*Dot1x_NW_MsgTask_0: May 09 11:45:03.773: 00:1b:77:b4:34:e0 Sending EAPOL-Key Message to mobile 00:1b:77:b4:34:e0
state INITPMK (message 1), replay counter 00.00.00.00.00.00.00.00
*Dot1x_NW_MsgTask_0: May 09 11:45:03.773: 00:1b:77:b4:34:e0 Sending EAPOL-Key Message to mobile 00:1b:77:b4:34:e0
state INITPMK (message 1), replay counter 00.00.00.00.00.00.00.00
*Dot1x_NW_MsgTask_0: May 09 11:45:03.773: 00:1b:77:b4:34:e0 Allocating EAP Pkt for retransmission to mobile 00:1b:77:b4:34:e0
*Dot1x_NW_MsgTask_0: May 09 11:45:03.773: 00:1b:77:b4:34:e0 mscb->apfMsLwappLradNhMac = 78:da:6e:59:c9:8c mscb->apfMsLradSlotId = 0 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
*Dot1x_NW_MsgTask_0: May 09 11:45:03.773: 00:1b:77:b4:34:e0 mscb->apfMsBssid = 18:9c:5d:71:34:50 mscb->apfMsAddress = 00:1b:77:b4:34:e0 mscb->apfMsApVapId = 1
*Dot1x_NW_MsgTask_0: May 09 11:45:03.773: 00:1b:77:b4:34:e0 dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 0 mscb->apfMsLwappMwarInet.ipv4.addr = -1062679171
*Dot1x_NW_MsgTask_0: May 09 11:45:03.773: 00:1b:77:b4:34:e0 mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = -1062679163 mscb->apfMsLwappLradPort = 40089
*osapiBsnTimer: May 09 11:45:05.849: 00:1b:77:b4:34:e0 802.1x 'timeoutEvt' Timer expired for station 00:1b:77:b4:34:e0 and for message = M2
*dot1xMsgTask: May 09 11:45:05.849: 00:1b:77:b4:34:e0 Retransmit 1 of EAPOL-Key M1 (length 121) for mobile 00:1b:77:b4:34:e0
*dot1xMsgTask: May 09 11:45:05.849: 00:1b:77:b4:34:e0 mscb->apfMsLwappLradNhMac = 78:da:6e:59:c9:8c mscb->apfMsLradSlotId = 0 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
*dot1xMsgTask: May 09 11:45:05.849: 00:1b:77:b4:34:e0 mscb->apfMsBssid = 18:9c:5d:71:34:50 mscb->apfMsAddress = 00:1b:77:b4:34:e0 mscb->apfMsApVapId = 1
*dot1xMsgTask: May 09 11:45:05.849: 00:1b:77:b4:34:e0 dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 0 mscb->apfMsLwappMwarInet.ipv4.addr = -1062679171
*dot1xMsgTask: May 09 11:45:05.849: 00:1b:77:b4:34:e0 mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = -1062679163 mscb->apfMsLwappLradPort = 40089
*osapiBsnTimer: May 09 11:45:07.848: 00:1b:77:b4:34:e0 802.1x 'timeoutEvt' Timer expired for station 00:1b:77:b4:34:e0 and for message = M2
*dot1xMsgTask: May 09 11:45:07.849: 00:1b:77:b4:34:e0 Retransmit 2 of EAPOL-Key M1 (length 121) for mobile 00:1b:77:b4:34:e0
*dot1xMsgTask: May 09 11:45:07.849: 00:1b:77:b4:34:e0 mscb->apfMsLwappLradNhMac = 78:da:6e:59:c9:8c mscb->apfMsLradSlotId = 0 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
*dot1xMsgTask: May 09 11:45:07.849: 00:1b:77:b4:34:e0 mscb->apfMsBssid = 18:9c:5d:71:34:50 mscb->apfMsAddress = 00:1b:77:b4:34:e0 mscb->apfMsApVapId = 1
*dot1xMsgTask: May 09 11:45:07.849: 00:1b:77:b4:34:e0 dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 0 mscb->apfMsLwappMwarInet.ipv4.addr = -1062679171
*dot1xMsgTask: May 09 11:45:07.849: 00:1b:77:b4:34:e0 mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = -1062679163 mscb->apfMsLwappLradPort = 40089
*osapiBsnTimer: May 09 11:45:09.848: 00:1b:77:b4:34:e0 802.1x 'timeoutEvt' Timer expired for station 00:1b:77:b4:34:e0 and for message = M2
*dot1xMsgTask: May 09 11:45:09.849: 00:1b:77:b4:34:e0 Retransmit failure for EAPOL-Key M1 to mobile 00:1b:77:b4:34:e0, retransmit count 3, mscb deauth count 3
*dot1xMsgTask: May 09 11:45:09.849: 00:1b:77:b4:34:e0 Blacklisting (if enabled) mobile 00:1b:77:b4:34:e0
*dot1xMsgTask: May 09 11:45:09.849: 00:1b:77:b4:34:e0 0.0.0.0 8021X_REQD (3) Change state to START (0) last state 8021X_REQD (3)
*dot1xMsgTask: May 09 11:45:09.849: 00:1b:77:b4:34:e0 0.0.0.0 START (0) Reached FAILURE: from line 5274
*dot1xMsgTask: May 09 11:45:09.849: 00:1b:77:b4:34:e0 Scheduling deletion of Mobile Station: (callerId: 9) in 10 seconds
*apfMsConnTask_4: May 09 11:45:15.689: 00:1b:77:b4:34:e0 Reassociation received from mobile on BSSID 18:9c:5d:71:34:50
*apfMsConnTask_4: May 09 11:45:15.689: 00:1b:77:b4:34:e0 Global 200 Clients are allowed to AP radio
*apfMsConnTask_4: May 09 11:45:15.689: 00:1b:77:b4:34:e0 Max Client Trap Threshold: 0 cur: 1
*apfMsConnTask_4: May 09 11:45:15.689: 00:1b:77:b4:34:e0 Rf profile 600 Clients are allowed to AP wlan
*apfMsConnTask_4: May 09 11:45:15.689: 00:1b:77:b4:34:e0 Applying Interface policy on Mobile, role Unassociated. Ms NAC State 2 Quarantine Vlan 0 Access Vlan 1
*apfMsConnTask_4: May 09 11:45:15.689: 00:1b:77:b4:34:e0 Re-applying interface policy for client
*apfMsConnTask_4: May 09 11:45:15.689: 00:1b:77:b4:34:e0 0.0.0.0 START (0) Changing IPv4 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2202)
*apfMsConnTask_4: May 09 11:45:15.689: 00:1b:77:b4:34:e0 0.0.0.0 START (0) Changing IPv6 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2223)
*apfMsConnTask_4: May 09 11:45:15.689: 00:1b:77:b4:34:e0 apfApplyWlanPolicy: Apply WLAN Policy over PMIPv6 Client Mobility Type
*apfMsConnTask_4: May 09 11:45:15.689: 00:1b:77:b4:34:e0 In processSsidIE:4795 setting Central switched to TRUE
*apfMsConnTask_4: May 09 11:45:15.689: 00:1b:77:b4:34:e0 In processSsidIE:4798 apVapId = 1 and Split Acl Id = 65535
*apfMsConnTask_4: May 09 11:45:15.690: 00:1b:77:b4:34:e0 Applying site-specific Local Bridging override for station 00:1b:77:b4:34:e0 - vapId 1, site 'default-group', interface 'catodos'
*apfMsConnTask_4: May 09 11:45:15.690: 00:1b:77:b4:34:e0 Applying Local Bridging Interface Policy for station 00:1b:77:b4:34:e0 - vlan 1, interface id 12, interface 'catodos'
*apfMsConnTask_4: May 09 11:45:15.690: 00:1b:77:b4:34:e0 processSsidIE statusCode is 0 and status is 0
*apfMsConnTask_4: May 09 11:45:15.690: 00:1b:77:b4:34:e0 processSsidIE ssid_done_flag is 0 finish_flag is 0
*apfMsConnTask_4: May 09 11:45:15.690: 00:1b:77:b4:34:e0 STA - rates (8): 2 4 11 22 12 18 24 36 48 72 96 108 0 0 0 0
*apfMsConnTask_4: May 09 11:45:15.690: 00:1b:77:b4:34:e0 suppRates statusCode is 0 and gotSuppRatesElement is 1
*apfMsConnTask_4: May 09 11:45:15.690: 00:1b:77:b4:34:e0 STA - rates (12): 2 4 11 22 12 18 24 36 48 72 96 108 0 0 0 0
*apfMsConnTask_4: May 09 11:45:15.690: 00:1b:77:b4:34:e0 extSuppRates statusCode is 0 and gotExtSuppRatesElement is 1
*apfMsConnTask_4: May 09 11:45:15.690: 00:1b:77:b4:34:e0 Processing RSN IE type 48, length 20 for mobile 00:1b:77:b4:34:e0
*apfMsConnTask_4: May 09 11:45:15.690: 00:1b:77:b4:34:e0 0.0.0.0 START (0) Initializing policy
*apfMsConnTask_4: May 09 11:45:15.690: 00:1b:77:b4:34:e0 0.0.0.0 START (0) Change state to AUTHCHECK (2) last state START (0)
*apfMsConnTask_4: May 09 11:45:15.690: 00:1b:77:b4:34:e0 0.0.0.0 AUTHCHECK (2) Change state to 8021X_REQD (3) last state AUTHCHECK (2)
*apfMsConnTask_4: May 09 11:45:15.690: 00:1b:77:b4:34:e0 Central switch is TRUE
*apfMsConnTask_4: May 09 11:45:15.690: 00:1b:77:b4:34:e0 Not Using WMM Compliance code qosCap 00
*apfMsConnTask_4: May 09 11:45:15.690: 00:1b:77:b4:34:e0 0.0.0.0 8021X_REQD (3) Plumbed mobile LWAPP rule on AP 18:9c:5d:71:34:50 vapId 1 apVapId 1 flex-acl-name:
*apfMsConnTask_4: May 09 11:45:15.690: 00:1b:77:b4:34:e0 apfPemAddUser2 (apf_policy.c:333) Changing state for mobile 00:1b:77:b4:34:e0 on AP 18:9c:5d:71:34:50 from Associated to Associated
*apfMsConnTask_4: May 09 11:45:15.690: 00:1b:77:b4:34:e0 apfPemAddUser2:session timeout forstation 00:1b:77:b4:34:e0 - Session Tout 1800, apfMsTimeOut '1800' and sessionTimerRunning flag is 0
*apfMsConnTask_4: May 09 11:45:15.690: 00:1b:77:b4:34:e0 Scheduling deletion of Mobile Station: (callerId: 49) in 1800 seconds
*apfMsConnTask_4: May 09 11:45:15.690: 00:1b:77:b4:34:e0 Func: apfPemAddUser2, Ms Timeout = 1800, Session Timeout = 1800
*apfMsConnTask_4: May 09 11:45:15.690: 00:1b:77:b4:34:e0 Sending Assoc Response to station on BSSID 18:9c:5d:71:34:50 (status 0) ApVapId 1 Slot 0
*apfMsConnTask_4: May 09 11:45:15.691: 00:1b:77:b4:34:e0 apfProcessAssocReq (apf_80211.c:8292) Changing state for mobile 00:1b:77:b4:34:e0 on AP 18:9c:5d:71:34:50 from Associated to Associated
*spamApTask6: May 09 11:45:15.693: 00:1b:77:b4:34:e0 Sent 1x initiate message to multi thread task for mobile 00:1b:77:b4:34:e0
*Dot1x_NW_MsgTask_0: May 09 11:45:15.693: 00:1b:77:b4:34:e0 Creating a PKC PMKID Cache entry for station 00:1b:77:b4:34:e0 (RSN 2)
*Dot1x_NW_MsgTask_0: May 09 11:45:15.693: 00:1b:77:b4:34:e0 Resetting MSCB PMK Cache Entry 0 for station 00:1b:77:b4:34:e0
*Dot1x_NW_MsgTask_0: May 09 11:45:15.693: 00:1b:77:b4:34:e0 Removing BSSID 18:9c:5d:71:34:50 from PMKID cache of station 00:1b:77:b4:34:e0
*Dot1x_NW_MsgTask_0: May 09 11:45:15.693: 00:1b:77:b4:34:e0 Setting active key cache index 0 ---> 8
*Dot1x_NW_MsgTask_0: May 09 11:45:15.693: 00:1b:77:b4:34:e0 Setting active key cache index 8 ---> 0
*Dot1x_NW_MsgTask_0: May 09 11:45:15.693: 00:1b:77:b4:34:e0 Adding BSSID 18:9c:5d:71:34:50 to PMKID cache at index 0 for station 00:1b:77:b4:34:e0
*Dot1x_NW_MsgTask_0: May 09 11:45:15.693: New PMKID: (16)
*Dot1x_NW_MsgTask_0: May 09 11:45:15.693: [0000] f6 3d 52 9f 2a de 52 90 1d a2 46 49 0f 14 f6 69
*Dot1x_NW_MsgTask_0: May 09 11:45:15.693: 00:1b:77:b4:34:e0 Initiating RSN PSK to mobile 00:1b:77:b4:34:e0
*Dot1x_NW_MsgTask_0: May 09 11:45:15.693: 00:1b:77:b4:34:e0 EAP-PARAM Debug - eap-params for Wlan-Id :1 is disabled - applying Global eap timers and retries
*Dot1x_NW_MsgTask_0: May 09 11:45:15.693: 00:1b:77:b4:34:e0 dot1x - moving mobile 00:1b:77:b4:34:e0 into Force Auth state
*Dot1x_NW_MsgTask_0: May 09 11:45:15.693: 00:1b:77:b4:34:e0 EAPOL Header:
*Dot1x_NW_MsgTask_0: May 09 11:45:15.694: 00000000: 02 03 00 5f ..._
*Dot1x_NW_MsgTask_0: May 09 11:45:15.694: 00:1b:77:b4:34:e0 Found an cache entry for BSSID 18:9c:5d:71:34:50 in PMKID cache at index 0 of station 00:1b:77:b4:34:e0
*Dot1x_NW_MsgTask_0: May 09 11:45:15.694: 00:1b:77:b4:34:e0 Found an cache entry for BSSID 18:9c:5d:71:34:50 in PMKID cache at index 0 of station 00:1b:77:b4:34:e0
*Dot1x_NW_MsgTask_0: May 09 11:45:15.694: Including PMKID in M1 (16)
*Dot1x_NW_MsgTask_0: May 09 11:45:15.694: [0000] f6 3d 52 9f 2a de 52 90 1d a2 46 49 0f 14 f6 69
*Dot1x_NW_MsgTask_0: May 09 11:45:15.694: 00:1b:77:b4:34:e0 Starting key exchange to mobile 00:1b:77:b4:34:e0, data packets will be dropped
*Dot1x_NW_MsgTask_0: May 09 11:45:15.694: 00:1b:77:b4:34:e0 Sending EAPOL-Key Message to mobile 00:1b:77:b4:34:e0
state INITPMK (message 1), replay counter 00.00.00.00.00.00.00.00
*Dot1x_NW_MsgTask_0: May 09 11:45:15.694: 00:1b:77:b4:34:e0 Sending EAPOL-Key Message to mobile 00:1b:77:b4:34:e0
state INITPMK (message 1), replay counter 00.00.00.00.00.00.00.00
*Dot1x_NW_MsgTask_0: May 09 11:45:15.694: 00:1b:77:b4:34:e0 Reusing allocated memory for EAP Pkt for retransmission to mobile 00:1b:77:b4:34:e0
*Dot1x_NW_MsgTask_0: May 09 11:45:15.694: 00:1b:77:b4:34:e0 mscb->apfMsLwappLradNhMac = 78:da:6e:59:c9:8c mscb->apfMsLradSlotId = 0 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
*Dot1x_NW_MsgTask_0: May 09 11:45:15.694: 00:1b:77:b4:34:e0 mscb->apfMsBssid = 18:9c:5d:71:34:50 mscb->apfMsAddress = 00:1b:77:b4:34:e0 mscb->apfMsApVapId = 1
*Dot1x_NW_MsgTask_0: May 09 11:45:15.694: 00:1b:77:b4:34:e0 dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 0 mscb->apfMsLwappMwarInet.ipv4.addr = -1062679171
*Dot1x_NW_MsgTask_0: May 09 11:45:15.694: 00:1b:77:b4:34:e0 mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = -1062679163 mscb->apfMsLwappLradPort = 40089
*apfMsConnTask_4: May 09 11:45:15.875: 00:1b:77:b4:34:e0 Reassociation received from mobile on BSSID 18:9c:5d:71:34:50
*apfMsConnTask_4: May 09 11:45:15.875: 00:1b:77:b4:34:e0 Global 200 Clients are allowed to AP radio
*apfMsConnTask_4: May 09 11:45:15.875: 00:1b:77:b4:34:e0 Max Client Trap Threshold: 0 cur: 1
*apfMsConnTask_4: May 09 11:45:15.875: 00:1b:77:b4:34:e0 Rf profile 600 Clients are allowed to AP wlan
*apfMsConnTask_4: May 09 11:45:15.876: 00:1b:77:b4:34:e0 Applying Interface policy on Mobile, role Unassociated. Ms NAC State 2 Quarantine Vlan 0 Access Vlan 1
*apfMsConnTask_4: May 09 11:45:15.876: 00:1b:77:b4:34:e0 Re-applying interface policy for client
*apfMsConnTask_4: May 09 11:45:15.876: 00:1b:77:b4:34:e0 0.0.0.0 8021X_REQD (3) Changing IPv4 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2202)
*apfMsConnTask_4: May 09 11:45:15.876: 00:1b:77:b4:34:e0 0.0.0.0 8021X_REQD (3) Changing IPv6 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2223)
*apfMsConnTask_4: May 09 11:45:15.876: 00:1b:77:b4:34:e0 apfApplyWlanPolicy: Apply WLAN Policy over PMIPv6 Client Mobility Type
*apfMsConnTask_4: May 09 11:45:15.876: 00:1b:77:b4:34:e0 In processSsidIE:4795 setting Central switched to TRUE
*apfMsConnTask_4: May 09 11:45:15.876: 00:1b:77:b4:34:e0 In processSsidIE:4798 apVapId = 1 and Split Acl Id = 65535
*apfMsConnTask_4: May 09 11:45:15.876: 00:1b:77:b4:34:e0 Applying site-specific Local Bridging override for station 00:1b:77:b4:34:e0 - vapId 1, site 'default-group', interface 'catodos'
*apfMsConnTask_4: May 09 11:45:15.876: 00:1b:77:b4:34:e0 Applying Local Bridging Interface Policy for station 00:1b:77:b4:34:e0 - vlan 1, interface id 12, interface 'catodos'
*apfMsConnTask_4: May 09 11:45:15.876: 00:1b:77:b4:34:e0 processSsidIE statusCode is 0 and status is 0
*apfMsConnTask_4: May 09 11:45:15.876: 00:1b:77:b4:34:e0 processSsidIE ssid_done_flag is 0 finish_flag is 0
*apfMsConnTask_4: May 09 11:45:15.876: 00:1b:77:b4:34:e0 STA - rates (8): 2 4 11 22 12 18 24 36 48 72 96 108 0 0 0 0
*apfMsConnTask_4: May 09 11:45:15.876: 00:1b:77:b4:34:e0 suppRates statusCode is 0 and gotSuppRatesElement is 1
*apfMsConnTask_4: May 09 11:45:15.876: 00:1b:77:b4:34:e0 STA - rates (12): 2 4 11 22 12 18 24 36 48 72 96 108 0 0 0 0
*apfMsConnTask_4: May 09 11:45:15.876: 00:1b:77:b4:34:e0 extSuppRates statusCode is 0 and gotExtSuppRatesElement is 1
*apfMsConnTask_4: May 09 11:45:15.876: 00:1b:77:b4:34:e0 Processing RSN IE type 48, length 20 for mobile 00:1b:77:b4:34:e0
*apfMsConnTask_4: May 09 11:45:15.876: 00:1b:77:b4:34:e0 0.0.0.0 8021X_REQD (3) Initializing policy
*apfMsConnTask_4: May 09 11:45:15.876: 00:1b:77:b4:34:e0 0.0.0.0 8021X_REQD (3) Change state to AUTHCHECK (2) last state 8021X_REQD (3)
*apfMsConnTask_4: May 09 11:45:15.876: 00:1b:77:b4:34:e0 0.0.0.0 AUTHCHECK (2) Change state to 8021X_REQD (3) last state AUTHCHECK (2)
*apfMsConnTask_4: May 09 11:45:15.876: 00:1b:77:b4:34:e0 Central switch is TRUE
*apfMsConnTask_4: May 09 11:45:15.876: 00:1b:77:b4:34:e0 Not Using WMM Compliance code qosCap 00
*apfMsConnTask_4: May 09 11:45:15.876: 00:1b:77:b4:34:e0 0.0.0.0 8021X_REQD (3) Plumbed mobile LWAPP rule on AP 18:9c:5d:71:34:50 vapId 1 apVapId 1 flex-acl-name:
*apfMsConnTask_4: May 09 11:45:15.876: 00:1b:77:b4:34:e0 apfPemAddUser2 (apf_policy.c:333) Changing state for mobile 00:1b:77:b4:34:e0 on AP 18:9c:5d:71:34:50 from Associated to Associated
*apfMsConnTask_4: May 09 11:45:15.877: 00:1b:77:b4:34:e0 apfPemAddUser2:session timeout forstation 00:1b:77:b4:34:e0 - Session Tout 1800, apfMsTimeOut '1800' and sessionTimerRunning flag is 0
*apfMsConnTask_4: May 09 11:45:15.877: 00:1b:77:b4:34:e0 Scheduling deletion of Mobile Station: (callerId: 49) in 1800 seconds
*apfMsConnTask_4: May 09 11:45:15.877: 00:1b:77:b4:34:e0 Func: apfPemAddUser2, Ms Timeout = 1800, Session Timeout = 1800
*apfMsConnTask_4: May 09 11:45:15.877: 00:1b:77:b4:34:e0 Sending Assoc Response to station on BSSID 18:9c:5d:71:34:50 (status 0) ApVapId 1 Slot 0
*apfMsConnTask_4: May 09 11:45:15.877: 00:1b:77:b4:34:e0 apfProcessAssocReq (apf_80211.c:8292) Changing state for mobile 00:1b:77:b4:34:e0 on AP 18:9c:5d:71:34:50 from Associated to Associated
*spamApTask6: May 09 11:45:15.878: 00:1b:77:b4:34:e0 Sent 1x initiate message to multi thread task for mobile 00:1b:77:b4:34:e0
*Dot1x_NW_MsgTask_0: May 09 11:45:15.879: 00:1b:77:b4:34:e0 Creating a PKC PMKID Cache entry for station 00:1b:77:b4:34:e0 (RSN 2)
*Dot1x_NW_MsgTask_0: May 09 11:45:15.879: 00:1b:77:b4:34:e0 Resetting MSCB PMK Cache Entry 0 for station 00:1b:77:b4:34:e0
*Dot1x_NW_MsgTask_0: May 09 11:45:15.879: 00:1b:77:b4:34:e0 Removing BSSID 18:9c:5d:71:34:50 from PMKID cache of station 00:1b:77:b4:34:e0
*Dot1x_NW_MsgTask_0: May 09 11:45:15.879: 00:1b:77:b4:34:e0 Setting active key cache index 0 ---> 8
*Dot1x_NW_MsgTask_0: May 09 11:45:15.879: 00:1b:77:b4:34:e0 Setting active key cache index 8 ---> 0
*Dot1x_NW_MsgTask_0: May 09 11:45:15.879: 00:1b:77:b4:34:e0 Adding BSSID 18:9c:5d:71:34:50 to PMKID cache at index 0 for station 00:1b:77:b4:34:e0
*Dot1x_NW_MsgTask_0: May 09 11:45:15.879: New PMKID: (16)
*Dot1x_NW_MsgTask_0: May 09 11:45:15.879: [0000] f6 3d 52 9f 2a de 52 90 1d a2 46 49 0f 14 f6 69
*Dot1x_NW_MsgTask_0: May 09 11:45:15.879: 00:1b:77:b4:34:e0 Initiating RSN PSK to mobile 00:1b:77:b4:34:e0
*Dot1x_NW_MsgTask_0: May 09 11:45:15.879: 00:1b:77:b4:34:e0 EAP-PARAM Debug - eap-params for Wlan-Id :1 is disabled - applying Global eap timers and retries
*Dot1x_NW_MsgTask_0: May 09 11:45:15.879: 00:1b:77:b4:34:e0 dot1x - moving mobile 00:1b:77:b4:34:e0 into Force Auth state
*Dot1x_NW_MsgTask_0: May 09 11:45:15.879: 00:1b:77:b4:34:e0 EAPOL Header:
*Dot1x_NW_MsgTask_0: May 09 11:45:15.879: 00000000: 02 03 00 5f ..._
*Dot1x_NW_MsgTask_0: May 09 11:45:15.879: 00:1b:77:b4:34:e0 Found an cache entry for BSSID 18:9c:5d:71:34:50 in PMKID cache at index 0 of station 00:1b:77:b4:34:e0
*Dot1x_NW_MsgTask_0: May 09 11:45:15.879: 00:1b:77:b4:34:e0 Found an cache entry for BSSID 18:9c:5d:71:34:50 in PMKID cache at index 0 of station 00:1b:77:b4:34:e0
*Dot1x_NW_MsgTask_0: May 09 11:45:15.879: Including PMKID in M1 (16)
*Dot1x_NW_MsgTask_0: May 09 11:45:15.879: [0000] f6 3d 52 9f 2a de 52 90 1d a2 46 49 0f 14 f6 69
*Dot1x_NW_MsgTask_0: May 09 11:45:15.879: 00:1b:77:b4:34:e0 Starting key exchange to mobile 00:1b:77:b4:34:e0, data packets will be dropped
*Dot1x_NW_MsgTask_0: May 09 11:45:15.879: 00:1b:77:b4:34:e0 Sending EAPOL-Key Message to mobile 00:1b:77:b4:34:e0
state INITPMK (message 1), replay counter 00.00.00.00.00.00.00.00
*Dot1x_NW_MsgTask_0: May 09 11:45:15.879: 00:1b:77:b4:34:e0 Sending EAPOL-Key Message to mobile 00:1b:77:b4:34:e0
state INITPMK (message 1), replay counter 00.00.00.00.00.00.00.00
*Dot1x_NW_MsgTask_0: May 09 11:45:15.879: 00:1b:77:b4:34:e0 Reusing allocated memory for EAP Pkt for retransmission to mobile 00:1b:77:b4:34:e0
*Dot1x_NW_MsgTask_0: May 09 11:45:15.879: 00:1b:77:b4:34:e0 mscb->apfMsLwappLradNhMac = 78:da:6e:59:c9:8c mscb->apfMsLradSlotId = 0 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
*Dot1x_NW_MsgTask_0: May 09 11:45:15.879: 00:1b:77:b4:34:e0 mscb->apfMsBssid = 18:9c:5d:71:34:50 mscb->apfMsAddress = 00:1b:77:b4:34:e0 mscb->apfMsApVapId = 1
*Dot1x_NW_MsgTask_0: May 09 11:45:15.879: 00:1b:77:b4:34:e0 dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 0 mscb->apfMsLwappMwarInet.ipv4.addr = -1062679171
*Dot1x_NW_MsgTask_0: May 09 11:45:15.879: 00:1b:77:b4:34:e0 mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = -1062679163 mscb->apfMsLwappLradPort = 40089
*osapiBsnTimer: May 09 11:45:18.048: 00:1b:77:b4:34:e0 802.1x 'timeoutEvt' Timer expired for station 00:1b:77:b4:34:e0 and for message = M2
*dot1xMsgTask: May 09 11:45:18.049: 00:1b:77:b4:34:e0 Retransmit 1 of EAPOL-Key M1 (length 121) for mobile 00:1b:77:b4:34:e0
*dot1xMsgTask: May 09 11:45:18.049: 00:1b:77:b4:34:e0 mscb->apfMsLwappLradNhMac = 78:da:6e:59:c9:8c mscb->apfMsLradSlotId = 0 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
*dot1xMsgTask: May 09 11:45:18.049: 00:1b:77:b4:34:e0 mscb->apfMsBssid = 18:9c:5d:71:34:50 mscb->apfMsAddress = 00:1b:77:b4:34:e0 mscb->apfMsApVapId = 1
*dot1xMsgTask: May 09 11:45:18.049: 00:1b:77:b4:34:e0 dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 0 mscb->apfMsLwappMwarInet.ipv4.addr = -1062679171
*dot1xMsgTask: May 09 11:45:18.049: 00:1b:77:b4:34:e0 mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = -1062679163 mscb->apfMsLwappLradPort = 40089
*osapiBsnTimer: May 09 11:45:20.049: 00:1b:77:b4:34:e0 802.1x 'timeoutEvt' Timer expired for station 00:1b:77:b4:34:e0 and for message = M2
*dot1xMsgTask: May 09 11:45:20.049: 00:1b:77:b4:34:e0 Retransmit 2 of EAPOL-Key M1 (length 121) for mobile 00:1b:77:b4:34:e0
*dot1xMsgTask: May 09 11:45:20.049: 00:1b:77:b4:34:e0 mscb->apfMsLwappLradNhMac = 78:da:6e:59:c9:8c mscb->apfMsLradSlotId = 0 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
*dot1xMsgTask: May 09 11:45:20.049: 00:1b:77:b4:34:e0 mscb->apfMsBssid = 18:9c:5d:71:34:50 mscb->apfMsAddress = 00:1b:77:b4:34:e0 mscb->apfMsApVapId = 1
*dot1xMsgTask: May 09 11:45:20.049: 00:1b:77:b4:34:e0 dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 0 mscb->apfMsLwappMwarInet.ipv4.addr = -1062679171
*dot1xMsgTask: May 09 11:45:20.049: 00:1b:77:b4:34:e0 mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = -1062679163 mscb->apfMsLwappLradPort = 40089
*osapiBsnTimer: May 09 11:45:22.048: 00:1b:77:b4:34:e0 802.1x 'timeoutEvt' Timer expired for station 00:1b:77:b4:34:e0 and for message = M2
*dot1xMsgTask: May 09 11:45:22.049: 00:1b:77:b4:34:e0 Retransmit failure for EAPOL-Key M1 to mobile 00:1b:77:b4:34:e0, retransmit count 3, mscb deauth count 0
*dot1xMsgTask: May 09 11:45:22.049: 00:1b:77:b4:34:e0 Resetting MSCB PMK Cache Entry 0 for station 00:1b:77:b4:34:e0
*dot1xMsgTask: May 09 11:45:22.049: 00:1b:77:b4:34:e0 Removing BSSID 18:9c:5d:71:34:50 from PMKID cache of station 00:1b:77:b4:34:e0
*dot1xMsgTask: May 09 11:45:22.049: 00:1b:77:b4:34:e0 Setting active key cache index 0 ---> 8
*dot1xMsgTask: May 09 11:45:22.049: 00:1b:77:b4:34:e0 Sent Deauthenticate to mobile on BSSID 18:9c:5d:71:34:50 slot 0(caller 1x_ptsm.c:598)
*dot1xMsgTask: May 09 11:45:22.049: 00:1b:77:b4:34:e0 Setting active key cache index 8 ---> 8
*dot1xMsgTask: May 09 11:45:22.049: 00:1b:77:b4:34:e0 Deleting the PMK cache when de-authenticating the client.
*dot1xMsgTask: May 09 11:45:22.049: 00:1b:77:b4:34:e0 Global PMK Cache deletion failed.
*dot1xMsgTask: May 09 11:45:22.049: 00:1b:77:b4:34:e0 Scheduling deletion of Mobile Station: (callerId: 57) in 10 seconds
*dot1xMsgTask: May 09 11:45:22.049: 00:1b:77:b4:34:e0 Freeing EAP Retransmit Bufer for mobile 00:1b:77:b4:34:e0
*osapiBsnTimer: May 09 11:45:32.048: 00:1b:77:b4:34:e0 apfMsExpireCallback (apf_ms.c:625) Expiring Mobile!
*apfReceiveTask: May 09 11:45:32.049: 00:1b:77:b4:34:e0 apfMsExpireMobileStation (apf_ms.c:6632) Changing state for mobile 00:1b:77:b4:34:e0 on AP 18:9c:5d:71:34:50 from Associated to Disassociated
*apfReceiveTask: May 09 11:45:32.049: 00:1b:77:b4:34:e0 Scheduling deletion of Mobile Station: (callerId: 45) in 10 seconds
Thanks for any adviceIn some of the big name brands of wireless, there is "no such thing" as 802.11n on a 2.4 Ghz. No such thing because Cisco won't allow you (any more) to do channel bonding of 2.4 Ghz. It doesn't make any sense to bond an already restricted 2.4 Ghz non-overlapping channel (three) and squeeze this number down to two.
Can you check to ensure that the data rates for 802.11b are enabled? Maybe someone disabled data rates from 1 Mbps to 11 Mbps. -
Hey All:
Ran into a strange issue today, two 2504 controller's, one upgraded (from 7.2 to 7.0 due to 1310 not working) to the new firmware fine, the other chucks back a signauture issue, i've seen alot of post's about the 5508 having this issue, but not much about the 2504, anyone got any idea's
The unit not working has PSJ15 serial number which i believe is from 2011, the working unit has a PSJ16 serial number. Any idea's would be very helpful
I dont want to shoot the disty down until i have some input
MattConsole into the 2504 and run the upgrade from the CLI:
transfer download serverip ip address of tftp server
transfer download datatype code
transfer download filename --filename of image
transfer download tftpMaxRetries 5
transfer download tftppktTimeout 3
debug transfer tftp enable --shows transfer progress
transfer download start -
Wlc 2504 7.4.100 to 7.4.110 upgrade fails
Hello,
I've got a strange behaviour while upgrading my 2504 wlc from 7.4.100 to 7.4.110. I used the gui procedure to transfer the updated aes file to the wlc. The procedure started fine, finished downloading, and then the wlc got completely stuck on "Writing New RTOS to flash" message, all ap loosed connection all clients down, claimings, etc... Then after more than 10 minutes watching my laptop screen I decided to hard reboot the wlc.
Initially I saw the new image booting but, at the end, I finally figured out that the backup image instead booted and the show boot from the controller shows the following:
(Cisco Controller) >show boot
Primary Boot Image............................... 7.4.110.0 (default)
Backup Boot Image................................ 7.4.100.0 (active)
The controller now is working fine with the old image, but I need the upgrade.
What do I have to do now ? I didn't understand what happened.
Thank you for your help
byeUpgrading to Controller Software Release 7.4.100.60
Guidelines and Limitations
• When H-REAP access points that are associated with a controller that has all the 7.0.x software releases that are prior to 7.0.240.0 upgrade to the 7.4.100.60 release, the access points lose their VLAN support configuration if it was enabled. The VLAN mappings revert to the default values of the VLAN of the associated interface. This issue does not occur if you upgrade from 7.0.240.0 or later 7.0.x release to the 7.4.100.60 release.
• While a client sends an HTTP request, the Controller intercepts it for redirection to login page. If the HTTP request intercepted by Controller is fragmented, the Controller drops the packet as the HTTP request does not contain enough information required for redirection.
• We recommend that you install Wireless LAN Controller Field Upgrade Software for Release 1.7.0.0-FUS, which is a special AES package that contains several system-related component upgrades. These include the bootloader, field recovery image, and FPGA/MCU firmware. Installing the FUS image requires special attention because it installs some critical firmware. The FUS image is independent of the runtime image. For more information, see http://www.cisco.com/en/US/docs/wireless/controller/release/notes/fus_rn_1_7_0_0.html.
• If you are using a Cisco 2500 Series controller and you intend to use the Application Visibility and Control (AVC) and NetFlow protocol features, you must install Wireless LAN Controller Field Upgrade Software for Release 1.8.0.0-FUS. This is not required if you are using other controller hardware models. For more information, see http://www.cisco.com/en/US/docs/wireless/controller/release/notes/fus_1_8_0_0.html.
• After you upgrade to the 7.4 release, networks that were not affected by the existing preauthentication ACLs might not work because the rules are now enforced. That is, networks with clients configured with static DNS servers might not work unless the static server is defined in the preauthentication ACL.
• On 7500 controllers if FIPS is enabled, the reduced boot options are displayed only after a bootloader upgrade.
Note Bootloader upgrade is not required if FIPS is disabled.
• If you require a downgrade from one release to another, you might lose the configuration from your current release. The workaround is to reload the previous controller configuration files saved on the backup server or to reconfigure the controller.
• It is not possible to directly upgrade to the 7.4.100.60 release from a release that is older than 7.0.98.0.
• You can upgrade or downgrade the controller software only between certain releases. In some instances, you must first install an intermediate release prior to upgrading to software release 7.4.100.60. Table 2 shows the upgrade path that you must follow before downloading software release 7.4.100.60.
For more information :
http://www.cisco.com/en/US/docs/wireless/controller/release/notes/crn74mr1.html#wp976667 -
WLC 2504 Connectivity Problems
This is a tricky one.
I installed a 2504 WLC with three AP's. Two SSID’s were configured, one with WPA2/AES-TIKIP and the other with Web Auth.
After installation, customers could connect to WLAN without problem and .
The problem that is occurring is that since the beginning of week, customers PDA's, cell phones and iPad and cannot access Internet with any of the two WLAN but clients who used laptop have no connection problems. Also the DHCP Server is assigning IP's correctly.
This problem also occurs with test SSID I created which is Open Auth. I see associated Cell phones and IPAD to the WLC but none of these answers ping from the WLC.
This is a WLC 2504 with IOS 7.4.100.Hello everyone!
Today I did a test with my Cell phone Samsung Note 2 and I have the same conectivity problem.
I have installed the APK ipconfig from the Play Store for Android in my cell phone and y see that I getting IP Address, Mask and Gateway.
This is what I´ve got from the APK:
IP ADDRESS 192.168.8.181
MASK: 255.255.255.0
GATEWAY: 192.168.8.2
DHCP SERVER: 192.168.8.16
DNS1: 192.168.6.16
DNS2: 192.168.2.16
I have connected my laptop to the WLAN with no issue and I´m getting this:
The IP address of the DHCP Server is 192.168.8.16 and 192.168.6.16 and is a Microsoft Server.
I´ve created a test WLAN with OPEN AUTH but the problem remains.
Here is the OUTPUT you requested:
show wlan 1
WLAN Identifier.................................. 1
Profile Name..................................... APS-PT-01
Network Name (SSID).............................. APS-PT-01
Status........................................... Enabled
MAC Filtering.................................... Disabled
Broadcast SSID................................... Enabled
AAA Policy Override.............................. Disabled
Network Admission Control
Client Profiling Status ....................... Disabled
DHCP ......................................... Disabled
HTTP ......................................... Disabled
Radius-NAC State............................... Disabled
SNMP-NAC State................................. Disabled
Quarantine VLAN................................ 0
Maximum number of Associated Clients............. 0
Maximum number of Clients per AP Radio........... 200
Number of Active Clients......................... 16
Exclusionlist Timeout............................ 60 seconds
Session Timeout.................................. 1800 seconds
User Idle Timeout................................ 300 seconds
User Idle Threshold.............................. 0 Bytes
NAS-identifier................................... APS-Admin-WLC-01
CHD per WLAN..................................... Enabled
Webauth DHCP exclusion........................... Disabled
Interface........................................ management
Multicast Interface.............................. Not Configured
WLAN IPv4 ACL.................................... unconfigured
WLAN IPv6 ACL.................................... unconfigured
mDNS Status...................................... Enabled
mDNS Profile Name................................ default-mdns-profile
DHCP Server...................................... Default
DHCP Address Assignment Required................. Disabled
Static IP client tunneling....................... Disabled
Quality of Service............................... Silver
Per-SSID Rate Limits............................. Upstream Downstream
Average Data Rate................................ 0 0
Average Realtime Data Rate....................... 0 0
Burst Data Rate.................................. 0 0
Burst Realtime Data Rate......................... 0 0
Per-Client Rate Limits........................... Upstream Downstream
Average Data Rate................................ 0 0
Average Realtime Data Rate....................... 0 0
Burst Data Rate.................................. 0 0
Burst Realtime Data Rate......................... 0 0
Scan Defer Priority.............................. 4,5,6
Scan Defer Time.................................. 100 milliseconds
WMM.............................................. Allowed
WMM UAPSD Compliant Client Support............... Disabled
Media Stream Multicast-direct.................... Disabled
CCX - AironetIe Support.......................... Enabled
CCX - Gratuitous ProbeResponse (GPR)............. Disabled
CCX - Diagnostics Channel Capability............. Disabled
Dot11-Phone Mode (7920).......................... Disabled
Wired Protocol................................... None
Passive Client Feature........................... Disabled
Peer-to-Peer Blocking Action..................... Disabled
Radio Policy..................................... All
DTIM period for 802.11a radio.................... 1
DTIM period for 802.11b radio.................... 1
Radius Servers
Authentication................................ Global Servers
Accounting.................................... Global Servers
Interim Update............................. Disabled
Dynamic Interface............................. Disabled
Dynamic Interface Priority.................... wlan
Local EAP Authentication......................... Disabled
Security
802.11 Authentication:........................ Open System
FT Support.................................... Disabled
Static WEP Keys............................... Disabled
802.1X........................................ Disabled
Wi-Fi Protected Access (WPA/WPA2)............. Enabled
WPA (SSN IE)............................... Enabled
TKIP Cipher............................. Enabled
AES Cipher.............................. Enabled
WPA2 (RSN IE).............................. Enabled
TKIP Cipher............................. Enabled
AES Cipher.............................. Enabled
Auth Key Management
802.1x.................................. Disabled
PSK..................................... Enabled
CCKM.................................... Disabled
FT-1X(802.11r).......................... Disabled
FT-PSK(802.11r)......................... Disabled
PMF-1X(802.11w)......................... Disabled
PMF-PSK(802.11w)........................ Disabled
FT Reassociation Timeout................... 20
FT Over-The-DS mode........................ Enabled
GTK Randomization.......................... Disabled
SKC Cache Support.......................... Disabled
CCKM TSF Tolerance......................... 1000
WAPI.......................................... Disabled
Wi-Fi Direct policy configured................ Disabled
EAP-Passthrough............................... Disabled
CKIP ......................................... Disabled
Web Based Authentication...................... Disabled
Web-Passthrough............................... Disabled
Conditional Web Redirect...................... Disabled
Splash-Page Web Redirect...................... Disabled
Auto Anchor................................... Disabled
FlexConnect Local Switching................... Disabled
flexconnect Central Dhcp Flag................. Disabled
flexconnect nat-pat Flag...................... Disabled
flexconnect Dns Override Flag................. Disabled
FlexConnect Vlan based Central Switching ..... Disabled
FlexConnect Local Authentication.............. Disabled
FlexConnect Learn IP Address.................. Enabled
Client MFP.................................... Optional
PMF........................................... Disabled
PMF Association Comeback Time................. 1
PMF SA Query RetryTimeout..................... 200
Tkip MIC Countermeasure Hold-down Timer....... 60
AVC Visibilty.................................... Disabled
AVC Profile Name................................. None
Flow Monitor Name................................ None
Call Snooping.................................... Disabled
Roamed Call Re-Anchor Policy..................... Disabled
SIP CAC Fail Send-486-Busy Policy................ Enabled
SIP CAC Fail Send Dis-Association Policy......... Disabled
KTS based CAC Policy............................. Disabled
Assisted Roaming Prediction Optimization......... Disabled
802.11k Neighbor List............................ Disabled
802.11k Neighbor List Dual Band.................. Disabled
Band Select...................................... Disabled
Load Balancing................................... Disabled
Multicast Buffer................................. Disabled
Mobility Anchor List
WLAN ID IP Address Status
802.11u........................................ Disabled
MSAP Services.................................. Disabled
(Cisco Controller) >
(Cisco Controller) >
(Cisco Controller) >show w?
wgb wlan wps
(Cisco Controller) >show wlan 2
WLAN Identifier.................................. 2
Profile Name..................................... APS-Visitas-PT
Network Name (SSID).............................. APS-Visitas-PT
Status........................................... Enabled
MAC Filtering.................................... Disabled
Broadcast SSID................................... Enabled
AAA Policy Override.............................. Disabled
Network Admission Control
Client Profiling Status ....................... Disabled
DHCP ......................................... Disabled
HTTP ......................................... Disabled
Radius-NAC State............................... Disabled
SNMP-NAC State................................. Disabled
Quarantine VLAN................................ 0
Maximum number of Associated Clients............. 0
Maximum number of Clients per AP Radio........... 200
Number of Active Clients......................... 1
Exclusionlist Timeout............................ 60 seconds
Session Timeout.................................. 1800 seconds
User Idle Timeout................................ 300 seconds
User Idle Threshold.............................. 0 Bytes
NAS-identifier................................... APS-Admin-WLC-01
CHD per WLAN..................................... Enabled
Webauth DHCP exclusion........................... Disabled
Interface........................................ management
Multicast Interface.............................. Not Configured
WLAN IPv4 ACL.................................... unconfigured
WLAN IPv6 ACL.................................... unconfigured
mDNS Status...................................... Enabled
mDNS Profile Name................................ default-mdns-profile
DHCP Server...................................... Default
DHCP Address Assignment Required................. Disabled
Static IP client tunneling....................... Disabled
Quality of Service............................... Silver
Per-SSID Rate Limits............................. Upstream Downstream
Average Data Rate................................ 0 0
Average Realtime Data Rate....................... 0 0
Burst Data Rate.................................. 0 0
Burst Realtime Data Rate......................... 0 0
Per-Client Rate Limits........................... Upstream Downstream
Average Data Rate................................ 0 0
Average Realtime Data Rate....................... 0 0
Burst Data Rate.................................. 0 0
Burst Realtime Data Rate......................... 0 0
Scan Defer Priority.............................. 4,5,6
Scan Defer Time.................................. 100 milliseconds
WMM.............................................. Allowed
WMM UAPSD Compliant Client Support............... Disabled
Media Stream Multicast-direct.................... Disabled
CCX - AironetIe Support.......................... Enabled
CCX - Gratuitous ProbeResponse (GPR)............. Disabled
CCX - Diagnostics Channel Capability............. Disabled
Dot11-Phone Mode (7920).......................... Disabled
Wired Protocol................................... None
Passive Client Feature........................... Disabled
Peer-to-Peer Blocking Action..................... Disabled
Radio Policy..................................... All
DTIM period for 802.11a radio.................... 1
DTIM period for 802.11b radio.................... 1
Radius Servers
Authentication................................ Global Servers
Accounting.................................... Global Servers
Interim Update............................. Disabled
Dynamic Interface............................. Disabled
Dynamic Interface Priority.................... wlan
Local EAP Authentication......................... Disabled
Security
802.11 Authentication:........................ Open System
FT Support.................................... Disabled
Static WEP Keys............................... Disabled
802.1X........................................ Disabled
Wi-Fi Protected Access (WPA/WPA2)............. Disabled
WAPI.......................................... Disabled
Wi-Fi Direct policy configured................ Disabled
EAP-Passthrough............................... Disabled
CKIP ......................................... Disabled
Web Based Authentication...................... Enabled
IPv4 ACL........................................ Unconfigured
IPv6 ACL........................................ Unconfigured
Web-Auth Flex ACL............................... Unconfigured
Web Authentication server precedence:
1............................................... local
2............................................... radius
3............................................... ldap
Web-Passthrough............................... Disabled
Conditional Web Redirect...................... Disabled
Splash-Page Web Redirect...................... Disabled
Auto Anchor................................... Disabled
FlexConnect Local Switching................... Disabled
flexconnect Central Dhcp Flag................. Disabled
flexconnect nat-pat Flag...................... Disabled
flexconnect Dns Override Flag................. Disabled
FlexConnect Vlan based Central Switching ..... Disabled
FlexConnect Local Authentication.............. Disabled
FlexConnect Learn IP Address.................. Enabled
Client MFP.................................... Optional but inactive (WPA2 not configured)
PMF........................................... Disabled
PMF Association Comeback Time................. 1
PMF SA Query RetryTimeout..................... 200
Tkip MIC Countermeasure Hold-down Timer....... 60
AVC Visibilty.................................... Disabled
AVC Profile Name................................. None
Flow Monitor Name................................ None
Call Snooping.................................... Disabled
Roamed Call Re-Anchor Policy..................... Disabled
SIP CAC Fail Send-486-Busy Policy................ Disabled
SIP CAC Fail Send Dis-Association Policy......... Disabled
KTS based CAC Policy............................. Disabled
Assisted Roaming Prediction Optimization......... Disabled
802.11k Neighbor List............................ Disabled
802.11k Neighbor List Dual Band.................. Disabled
Band Select...................................... Disabled
Load Balancing................................... Disabled
Multicast Buffer................................. Disabled
Mobility Anchor List
WLAN ID IP Address Status
802.11u........................................ Disabled
MSAP Services.................................. Disabled
(Cisco Controller) >
(Cisco Controller) >show wlan 3
WLAN Identifier.................................. 3
Profile Name..................................... Prueba
Network Name (SSID).............................. Prueba
Status........................................... Enabled
MAC Filtering.................................... Disabled
Broadcast SSID................................... Enabled
AAA Policy Override.............................. Disabled
Network Admission Control
Client Profiling Status ....................... Disabled
DHCP ......................................... Disabled
HTTP ......................................... Disabled
Radius-NAC State............................... Disabled
SNMP-NAC State................................. Disabled
Quarantine VLAN................................ 0
Maximum number of Associated Clients............. 0
Maximum number of Clients per AP Radio........... 200
Number of Active Clients......................... 0
Exclusionlist Timeout............................ 60 seconds
Session Timeout.................................. 1800 seconds
User Idle Timeout................................ 300 seconds
User Idle Threshold.............................. 0 Bytes
NAS-identifier................................... APS-Admin-WLC-01
CHD per WLAN..................................... Enabled
Webauth DHCP exclusion........................... Disabled
Interface........................................ management
Multicast Interface.............................. Not Configured
WLAN IPv4 ACL.................................... unconfigured
WLAN IPv6 ACL.................................... unconfigured
mDNS Status...................................... Enabled
mDNS Profile Name................................ default-mdns-profile
DHCP Server...................................... Default
DHCP Address Assignment Required................. Disabled
Static IP client tunneling....................... Disabled
Quality of Service............................... Silver
Per-SSID Rate Limits............................. Upstream Downstream
Average Data Rate................................ 0 0
Average Realtime Data Rate....................... 0 0
Burst Data Rate.................................. 0 0
Burst Realtime Data Rate......................... 0 0
Per-Client Rate Limits........................... Upstream Downstream
Average Data Rate................................ 0 0
Average Realtime Data Rate....................... 0 0
Burst Data Rate.................................. 0 0
Burst Realtime Data Rate......................... 0 0
Scan Defer Priority.............................. 4,5,6
Scan Defer Time.................................. 100 milliseconds
WMM.............................................. Allowed
WMM UAPSD Compliant Client Support............... Enabled
Media Stream Multicast-direct.................... Disabled
CCX - AironetIe Support.......................... Disabled
CCX - Gratuitous ProbeResponse (GPR)............. Disabled
CCX - Diagnostics Channel Capability............. Disabled
Dot11-Phone Mode (7920).......................... Disabled
Wired Protocol................................... None
Passive Client Feature........................... Disabled
Peer-to-Peer Blocking Action..................... Disabled
Radio Policy..................................... All
DTIM period for 802.11a radio.................... 1
DTIM period for 802.11b radio.................... 1
Radius Servers
Authentication................................ Global Servers
Accounting.................................... Global Servers
Interim Update............................. Disabled
Dynamic Interface............................. Disabled
Dynamic Interface Priority.................... wlan
Local EAP Authentication......................... Disabled
Security
802.11 Authentication:........................ Open System
FT Support.................................... Enabled
Static WEP Keys............................... Disabled
802.1X........................................ Disabled
Wi-Fi Protected Access (WPA/WPA2)............. Disabled
WAPI.......................................... Disabled
Wi-Fi Direct policy configured................ Disabled
EAP-Passthrough............................... Disabled
CKIP ......................................... Disabled
Web Based Authentication...................... Disabled
Web-Passthrough............................... Disabled
Conditional Web Redirect...................... Disabled
Splash-Page Web Redirect...................... Disabled
Auto Anchor................................... Disabled
FlexConnect Local Switching................... Disabled
flexconnect Central Dhcp Flag................. Disabled
flexconnect nat-pat Flag...................... Disabled
flexconnect Dns Override Flag................. Disabled
FlexConnect Vlan based Central Switching ..... Disabled
FlexConnect Local Authentication.............. Disabled
FlexConnect Learn IP Address.................. Enabled
Client MFP.................................... Disabled
PMF........................................... Disabled
PMF Association Comeback Time................. 1
PMF SA Query RetryTimeout..................... 200
Tkip MIC Countermeasure Hold-down Timer....... 60
AVC Visibilty.................................... Disabled
AVC Profile Name................................. None
Flow Monitor Name................................ None
Call Snooping.................................... Disabled
Roamed Call Re-Anchor Policy..................... Disabled
SIP CAC Fail Send-486-Busy Policy................ Disabled
SIP CAC Fail Send Dis-Association Policy......... Disabled
KTS based CAC Policy............................. Disabled
Assisted Roaming Prediction Optimization......... Disabled
802.11k Neighbor List............................ Disabled
802.11k Neighbor List Dual Band.................. Disabled
Band Select...................................... Disabled
Load Balancing................................... Disabled
Multicast Buffer................................. Disabled
Mobility Anchor List
WLAN ID IP Address Status
802.11u........................................ Disabled
MSAP Services.................................. Disabled -
WLC: 2504
Firmware: 7.6.100
Hello,
I'm getting very confused in how to set up redundancy with WLC 2504. Some sources talk about Client SSO, some about N+1.
But it seems that although I should use Client SSO with firmware 7.6, the WLC 2504 doesn't support it.
When I type config redundancy, I have no choice
>config redundancy ?
unit Configure redundancy unit [primary | secondary]
So I typed "config redundancy unit primary" on my 2504 and "config redundancy unit secondary" on my 2504-HA
And when I issue this command I have very little information
>show redundancy summary
Type of the Unit = Primary
Does someone has guidelines for redundancy with WLC 2504 on firmware 7.6 ?
Thank youHello,
Thank you both for your answers.
Something I didn't understand in the documentation is this.
Is there a replication of configuration between the WLC primary and the HA ? I did read that they should have different network settings (IP addresses) so I understand that there is not a total replication, what about the rest of the configuration ?
The only result I have when I issue a command on the WLC-HA is this
>show redundancy summary
Type of the Unit = Secondary
It doesn't look exactly what I see in the documentation.
Thank you -
DEBUG-4-INVALID_MODULE on the WLC 2504 with version 7.6.100????
Hi!!! Please help with the solution.
I have one WLC 2504, 4 Cisco 1141 APs and one AP 1602.
Yesterday, I upgrade the WLC with version 7.5.102 to version 7.6.100.
After the upgrade in Message Logs on the WLC at the same time see the following message:
*RRM-MGR-5_0-GRP: Jan 23 08:44:25.449: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 08:35:41.189: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 08:34:17.373: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 08:25:32.125: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 08:24:09.309: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 08:15:23.013: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 08:14:01.213: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 08:05:13.949: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 08:03:53.149: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 07:55:04.905: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 07:53:45.086: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 07:44:55.813: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 07:43:37.010: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 07:34:46.749: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 07:33:28.930: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 07:24:37.669: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 07:23:20.865: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 07:14:28.593: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 07:13:12.789: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 07:04:19.529: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 07:03:04.729: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 06:54:10.493: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 06:52:56.689: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 06:44:01.445: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 06:42:48.645: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.
*sntpReceiveTask: Jan 23 06:35:22.218: #LOG-4-Q_IND: debug.c:2636 Unhandled debug module 5005.[...It occurred 19 times.!]
*RRM-MGR-2_4-GRP: Jan 23 06:33:48.070: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 06:32:36.266: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 06:23:39.030: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 06:22:28.226: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 06:13:29.986: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 06:12:20.186: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 06:03:20.930: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 06:02:12.130: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 05:53:11.890: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 05:52:04.090: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 05:43:02.838: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 05:41:56.039: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 05:32:53.790: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 05:31:47.986: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 05:22:44.758: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 05:21:39.950: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 05:12:35.718: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 05:11:31.910: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 05:02:26.670: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 05:01:23.859: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 04:52:17.606: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 04:51:15.794: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 04:42:08.566: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 04:41:07.750: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 04:31:59.506: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 04:30:59.703: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 04:21:50.450: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 04:20:51.646: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 04:11:41.402: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 04:10:43.598: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 04:01:32.326: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 04:00:35.522: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 03:51:23.258: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 03:50:27.442: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 03:41:14.182: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 03:40:19.378: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 03:31:05.106: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 03:30:11.302: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 03:20:56.042: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 03:20:03.242: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 03:10:46.978: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 03:09:55.178: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 03:00:37.902: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 02:59:47.102: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 02:50:28.826: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 02:49:39.026: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 02:40:19.782: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 02:39:30.983: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 02:30:10.742: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 02:29:22.942: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 02:20:01.698: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 02:19:14.886: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 02:09:52.646: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 02:09:06.842: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 01:59:43.587: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 01:58:58.783: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 01:49:34.546: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 01:48:50.742: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 01:39:25.494: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 01:38:42.687: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 01:29:16.454: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 01:28:34.642: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 01:19:07.402: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 01:18:26.594: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 01:08:58.362: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 01:08:18.554: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 00:58:49.322: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 00:58:10.514: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 00:48:40.266: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 00:48:02.467: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 00:38:31.222: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 00:37:54.411: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 00:28:22.174: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 00:27:46.374: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 00:18:13.106: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 00:17:38.306: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 00:08:04.062: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 00:07:30.262: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 22 23:57:55.022: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 22 23:57:22.222: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 22 23:47:45.958: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 22 23:47:14.158: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 22 23:37:36.906: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 22 23:37:06.106: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 22 23:27:27.826: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 22 23:26:58.026: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 22 23:17:18.762: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 22 23:16:49.962: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 22 23:07:09.686: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 22 23:06:41.870: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.
With what may be the problem exists? Any suggestion?Have you upgraded the FUS to 1.8.0.0? What happens if you try to boot from v7.5 do you see the messages and maybe boot back to v7.6?
Here is what the doc mentions about the error
Error Message %DEBUG-4-INVALID_MODULE: Unhandled debug module [dec].
Explanation This module cannot be debugged.
Recommended Action Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.
http://www.cisco.com/en/US/docs/wireless/controller/message/guide/msgs4.html#wp1000708
Sent from Cisco Technical Support iPhone App -
WLC 2504 can't change WAP name or switch off CDP via WLC gui
Hi All,
Please can you assist? I have 1 x Cisco WLC 2504 & 2 x Cisco WAP AIR-CAP1602I-E-K9 running 7.4.100.60.
All three devices are installed and working correcty within a corporate environment. However, there are a few tweaks that I would like to do, to tidy up the configuration and switch certain elements on or off. For example, my core networking hardware is Huawei and I would like to switch off 'CDP' on the WAP's as the associated error messages are filling up my logging buffer on my switch. So, I https to my WLC, locate the WAP in question, goto 'interfaces' and untick the box for 'CDP state' hit apply, then I get the following error message "controller name is mandatory when controller ip address is configured" and then the tick reappears!
At present I have two WAP's. Both have static IP addresses and both are reachable on the network. The one WAP did allow me to change the name to something meaningful, but the other WAP would not let me and still has the default MAC address as its name. I have the same issue, when I try to change the name on the WAP it says "controller name is mandatory when controller ip address is configured"
I have also tried to CLI directly in to the WAP to make these alterations, but as soon as i launch 'putty' it quits out. I guess this is locked down once the WAP's associate with the WLC.
And around I go.... Someone must have been in this situation, what am i missing? Thanks in advance!Hi Andy,
By default SSH & Telnet is disabled for WLC controlled APs. So you have to enable it first via WLC GUI in order to access the AP via telnet or SSH.
Wireless -> Select your AP -> Advanced -> Tick Telnet/SSH boxes.
If you could not change AP name via WLC GUI (it may be a bug), but as I said earlier try to change it via WLC CLI (not AP CLI itself). SSH to your WLC & then try the following.Old AP name is the one with its mac address.
(WLC) >config ap name
(WLC) >save config
Are you sure you want to save? (y/n) y
Configuration Saved
HTH
Rasika
*** Pls rate all useful responses **** -
Cisco WLC 2504 and ways to authenticate users
Hi All,
What is the ways to make user authenticate to WLC 2504 and what is the best and simple way and what is the differences btw each method _i mean for example need radius server or something else to be exist_ ?
and any one can give me case study for this issue
System consist of Cisco 2504 and Cisco LAP 1140
ThanksTo implement radius based authentication is the best practice for the small & enterprise environment.
Information About RADIUS
Remote Authentication Dial-In User Service (RADIUS) is a client/server protocol that provides centralized security for users attempting to gain management access to a network. It serves as a backend database similar to local and TACACS+ and provides authentication and accounting services:
•Authentication—The process of verifying users when they attempt to log into the controller.
Users must enter a valid username and password in order for the controller to authenticate users to the RADIUS server. If multiple databases are configured, you can specify the sequence in which the backend database must be tired.
•Accounting—The process of recording user actions and changes.
Whenever a user successfully executes an action, the RADIUS accounting server logs the changed attributes, the user ID of the person who made the change, the remote host where the user is logged in, the date and time when the command was executed, the authorization level of the user, and a description of the action performed and the values provided. If the RADIUS accounting server becomes unreachable, users are able to continue their sessions uninterrupted.
RADIUS uses User Datagram Protocol (UDP) for its transport. It maintains a database and listens on UDP port 1812 for incoming authentication requests and UDP port 1813 for incoming accounting requests. The controller, which requires access control, acts as the client and requests AAA services from the server. The traffic between the controller and the server is encrypted by an algorithm defined in the protocol and a shared secret key configured on both devices.
You can configure multiple RADIUS accounting and authentication servers.For example, you may want to have one central RADIUS authentication server but several RADIUS accounting servers in different regions. If you configure multiple servers of the same type and the first one fails or becomes unreachable, the controller automatically tries the second one, then the third one if necessary, and so on.
For more Information : http://www.cisco.com/en/US/docs/wireless/controller/7.2/configuration/guide/cg_security_sol.html#wp2149947 -
Hi all,
Just a little question about high availability in cisco 2504 WLC Ver 7.5.102.0.
Following the cisco documentation for WLC I want to set the HA configuration by going to Controller - Redundancy menu. My issue is that this menu does not exist in my WLC.
Anyone know if this version of ios is HA capable or not ?
Thanks
Fabien.Hi,
When the active controller is unavailable, the standby controller will adopt the licenses from the primary controller. It is expected that the you will be able to get the primary controller back online within 90 days. After 90 days, the you will get a daily reminder to switch back to the primary controller.
http://www.cisco.com/en/US/prod/collateral/wireless/ps6302/ps8322/ps10315/qa_c67-714540.html
Table 1. Controller Support for -HA and Stateful Switchover
Controller Model
SKU
Supports N+1
Supports SSO
5508
AIR-CT5508-HA-K9
Yes
Yes
WiSM2
WS-SVC-WISM2HA-K9=
WS-SVC-WISM2-HA-K9
Yes
Yes
Flex 7500
AIR-CT7510-HA-K9
Yes
Yes
8500
AIR-CT8510-HA-K9
Yes
Yes
2500
AIR-CT2504-HA-K9
Yes
No
UC blade on ISR G2
No
Yes
No
Virtual controller
No
Yes
No
regards -
I have two WLC 2504 controllers. These controllers are for two different buildings. But they share a VLAN, and network address range.
How can I control the access points to the register selected only at a specific controller.
Example:
AP 1 -> WLC 1
AP 2 -> WLC 2
AP 3 -> WLC 1
Since the buildings also broadcast in different SSID.
The two controllers are in a mobility group.I also ran into an install similar to yours. My client had a flat network and each wlc had licenses for the amount of APs in a particular building. What I did to make sure the APs never join the other wlc, is to use a Mac list. This allowed me to enter the APs base Mac address on the wlc and I enabled under the ap policy to verify authorization using Mac list. You can also do what AA mentioned which is good practice, but you have a chance that APs might join the other wlc. If the other wlc has different configurations, it might cause issues until the ap falls back to its primary.
Sent from Cisco Technical Support iPad App -
Iphones, Ipads face problem while shifting between diffrent WLAN on WLC 2504
Dear All,
I just create second SSID for different WLAN on my WLC 2504, all client other then Apple devices are successfully able to connect to new SSID a dnd can swap between two SSIDs but apple device unable to shift to new SSID, if any apple device is not connected to to any of SSID (Fresh connection) then that device is able to connect either of SSID but then unable to swap to other SSID. I enable Fast Transition on WLC as well but no improvement. can any one help me to sort out this issue
WLAN 10.10.10.0/24 SSID1
WLAN 10.10.20.0/24 SSID2
Thanks & Regards
ZohaibIssue resolved :) by configuring fast SSID changing
got help on following link
https://supportforums.cisco.com/discussion/11527996/difficulty-apple-ios-devices -
Why LAP1131AG and LAP11412 cannot to join WLC 2504?
I have WLC 2504, Cisco LAP1131AG and then Cisco LAP1142N. Why LAP1131AG and LAP11412 cannot to join WLC 2504?
this is error code at the Cisco LAP1131AG
*Sep 12 19:30:27.730: %CAPWAP-3-ERRORLOG: Go join a capwap controller
*Sep 12 19:30:27.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 192.168.100.10 peer_port: 5246
*Sep 12 19:30:57.001: DTLS_CLIENT_ERROR: ../capwap/base_capwap/dtls/base_capwap_dtls_connection_db.c:2051 Max retransmission count reached!
*Sep 12 19:31:27.000: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 192.168.100.10:5246
*Sep 12 19:31:32.083: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to administratively down
*Sep 12 19:31:32.083: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to administratively down
*Sep 12 19:31:32.085: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to up
*Sep 12 19:31:32.117: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does not have an Ip !!
*Sep 12 19:31:32.118: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to up
*Sep 12 19:31:33.083: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to down
*Sep 12 19:31:33.112: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to down
*Sep 12 19:31:33.117: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*Sep 12 19:31:34.104: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to up
*Sep 12 19:31:34.111: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*Sep 12 19:31:34.142: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to up
*Sep 12 19:31:34.147: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to down
*Sep 12 19:31:34.152: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset
*Sep 12 19:31:35.141: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
*Sep 12 19:31:35.146: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to down
*Sep 12 19:31:35.170: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to up
*Sep 12 19:31:36.171: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to up
this is version LAP1131AG
AP0018.18fc.fd58#sh version
Cisco IOS Software, C1130 Software (C1130-K9W8-M), Version 12.4(25e)JAO6, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2014 by Cisco Systems, Inc.
Compiled Fri 22-Aug-14 10:07 by prod_rel_team
ROM: Bootstrap program is C1130 boot loader
BOOTLDR: C1130 Boot Loader (C1130-BOOT-M) Version 12.3(7)JA1, RELEASE SOFTWARE (fc1)
AP0018.18fc.fd58 uptime is 9 minutes
System returned to ROM by power-on
System image file is "flash:/c1130-k9w8-mx.124-25e.JAO6/c1130-k9w8-mx.124-25e.JAO6"
and then this is version WLC2504
(Cisco Controller) >show sysinfo
Manufacturer's Name.............................. Cisco Systems Inc.
Product Name..................................... Cisco Controller
Product Version.................................. 7.6.130.0
Bootloader Version............................... 1.0.20
Field Recovery Image Version..................... 7.6.101.1
Firmware Version................................. PIC 16.0
Build Type....................................... DATA + WPS
System Name...................................... Cisco_47:19:c4
System Location..................................
System Contact...................................
System ObjectID.................................. 1.3.6.1.4.1.9.1.1279
IP Address....................................... 192.168.100.10
Last Reset....................................... Software reset
System Up Time................................... 0 days 0 hrs 36 mins 45 secs
System Timezone Location.........................
System Stats Realtime Interval................... 5
System Stats Normal Interval..................... 180
--More-- or (q)uit
Configured Country............................... ID - Indonesia
Operating Environment............................ Commercial (0 to 40 C)
Internal Temp Alarm Limits....................... 0 to 65 C
Internal Temperature............................. +34 C
External Temperature............................. +40 C
Fan Status....................................... 4100 rpm
State of 802.11b Network......................... Enabled
State of 802.11a Network......................... Enabled
Number of WLANs.................................. 1
Number of Active Clients......................... 0
Burned-in MAC Address............................ 24:E9:B3:47:19:C0
Maximum number of APs supported.................. 5
IP Address management WLC : 192.168.100.10/24
IP Address LAP1142N :192.168.100.102/24
IP Address LAP1131AG : 192.168.100.101/24
Can anyone help my problem?A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
[email protected]
cisco AIR-LAP1142N-A-K9 (PowerPC405ex) processor (revision A0) with 90102K/40960K bytes of memory.
Processor board ID FGL1439S15W
PowerPC405ex CPU at 586MHz, revision number 0x147E
Last reset from reload
LWAPP image version 7.6.130.0
1 Gigabit Ethernet interface
2 802.11 Radios
32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: C8:4C:75:79:EB:E9
Part Number : 73-12836-03
PCA Assembly Number : 800-33767-03
PCA Revision Number : A0
PCB Serial Number : FOC14234D8Z
Top Assembly Part Number : 800-33775-02
Top Assembly Serial Number : FGL1439S15W
Top Revision Number : A0
Product/Model Number : AIR-LAP1142N-A-K9
cisco AIR-LAP1131AG-A-K9 (PowerPCElvis) processor (revision A0) with 27638K/5120K bytes of memory.
Processor board ID FTX1026T46E
PowerPCElvis CPU at 262Mhz, revision number 0x0950
Last reset from power-on
LWAPP image version 7.6.130.0
1 FastEthernet interface
2 802.11 Radio(s)
32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: 00:18:18:FC:FD:58
Part Number : 73-8962-09
PCA Assembly Number : 800-24818-08
PCA Revision Number : A0
PCB Serial Number : FOC102513DE
Top Assembly Part Number : 800-25544-06
Top Assembly Serial Number : FTX1026T46E
Top Revision Number : A0
Product/Model Number : AIR-LAP1131AG-A-K9
Configuration register is 0xF
Maybe you are looking for
-
SAP Business Workflow in a multiple ERP environment
Hi, Our organization is looking to implement Peoplesoft for HR and SAP ERP for other business processes. Business users would ues UWL for their approval tasks. The SAP Business workflow or SAP NW BPM would be the tool for the approval process. Questi
-
Replacing Apple TV with Xbox 360, Video Questions
I have had an ATV for a little over a year and thanks to Handbrake I now have an incredible Movie Library over 600 flicks ripped for ATV with the .m4v extension. This month I am getting an Xbox 360 and would like to use it in place of my ATV and move
-
How do you get dvds to work on regular dvd players? It works on PC dvd player just fine.
I created a movie via Elements 13 (Using Windows 7) using video from my camcorder. I added menus and such and then burned it to a DVD -R using Elements 13. The dvd will play on a computer via the dvd player but it won't play on a regular dvd player
-
Can I get a notification upon responding to my message?
I put a message in the board. Is there a setup so that I get a notification in my e-mail when somebody answers my message? Thanks Rafi
-
[Solved]Xfce fonts look strange in Terminal
Never had this before maybe something went wrong on the catalyst installation, can't really describe it either so I will just post a picture. Hope that you can help it isn't really fatally but it's just ugly Last edited by heldiho53 (2014-10-01 18:56