WLC 5508 and Cisco Aironet 1242 LWAPP AIR-LAP1242AG-A-K9
i have deployed wlc 5508 ( image 7.0.98.0 ) with 1262N AP and all 45 AP's are working fine,
at the same site i had AP1242 which i have converted to LWAPP (8 of them), these accesspoint are registerd perfectly with 5508 but non of the radio's are up. i have selected different countries according to the part numbers but unfortunaly non of the radio's are coming up, pleaes help
Sathees
Available:370.0(w) Used:32.4(w) Remaining:337.6(w)
Interface Admin Oper Power Device Class
(Watts)
Fa0/1 auto off 0.0 n/a n/a
Fa0/2 auto off 0.0 n/a n/a
Fa0/3 auto off 0.0 n/a n/a
Fa0/4 auto off 0.0 n/a n/a
Fa0/5 auto off 0.0 n/a n/a
Fa0/6 auto off 0.0 n/a n/a
Fa0/7 auto off 0.0 n/a n/a
Fa0/8 auto off 0.0 n/a n/a
Fa0/9 auto off 0.0 n/a n/a
Fa0/10 auto off 0.0 n/a n/a
Fa0/11 auto off 0.0 n/a n/a
Fa0/12 auto off 0.0 n/a n/a
Fa0/13 auto off 0.0 n/a n/a
Fa0/14 auto off 0.0 n/a n/a
Fa0/15 auto off 0.0 n/a n/a
Fa0/16 auto off 0.0 n/a n/a
Fa0/17 auto off 0.0 n/a n/a
Fa0/18 auto off 0.0 n/a n/a
--More--
Interface Admin Oper Power Device Class
(Watts)
Fa0/19 auto off 0.0 n/a n/a
Fa0/20 auto off 0.0 n/a n/a
Fa0/21 auto off 0.0 n/a n/a
Fa0/22 auto off 0.0 n/a n/a
Fa0/23 auto off 0.0 n/a n/a
Fa0/24 auto off 0.0 n/a n/a
Fa0/25 auto off 0.0 n/a n/a
Fa0/26 auto off 0.0 n/a n/a
Fa0/27 auto off 0.0 n/a n/a
Fa0/28 auto off 0.0 n/a n/a
Fa0/29 auto off 0.0 n/a n/a
Fa0/30 auto off 0.0 n/a n/a
Fa0/31 auto off 0.0 n/a n/a
Fa0/32 auto off 0.0 n/a n/a
Fa0/33 auto off 0.0 n/a n/a
Fa0/34 auto off 0.0 n/a n/a
Fa0/35 auto off 0.0 n/a n/a
Fa0/36 auto off 0.0 n/a n/a
Fa0/37 auto off 0.0 n/a n/a
Fa0/38 auto off 0.0 n/a n/a
Fa0/39 auto off 0.0 n/a n/a
Fa0/40 auto off 0.0 n/a n/a
Fa0/41 auto on 15.0 cisco AIR-LAP1242AG Class 3
--More--
Interface Admin Oper Power Device Class
(Watts)
Fa0/42 auto off 0.0 n/a n/a
Fa0/43 auto on 5.8 cisco AIR-LAP1242AG Class 3
Fa0/44 auto off 0.0 n/a n/a
Fa0/45 auto on 5.8 cisco AIR-LAP1242AG Class 3
Fa0/46 auto off 0.0 n/a n/a
Fa0/47 auto on 5.8 cisco AIR-LAP1242AG Class 3
Fa0/48 auto off 0.0 n/a n/a
Similar Messages
-
Port channel WLC 5508 and 3750
Hi All,
I want to configure Port channel for WLC 5508 and cisco 3750 Stack Switch. What changes I need to make on WLC and where?
Thanks
JagdevThanks Chris,
LAG is enable on WLC, and Port channel is configured on 3750, Please see the configration and Port channel status below:-
(Cisco Controller) >show lag summary
LAG Enabled
interface Port-channel14
description Port Channel to WLC001
switchport trunk encapsulation dot1q
switchport mode trunk
end
sh etherchannel 14 summary
Flags: D - down P - bundled in port-channel
I - stand-alone s - suspended
H - Hot-standby (LACP only)
R - Layer3 S - Layer2
U - in use f - failed to allocate aggregator
M - not in use, minimum links not met
u - unsuitable for bundling
w - waiting to be aggregated
d - default port
Number of channel-groups in use: 14
Number of aggregators: 14
Group Port-channel Protocol Ports
------+-------------+-----------+-----------------------------------------------
14 Po14(SD) LACP Gi1/0/22(I) Gi2/0/22(I)
sh run int g1/0/22
Building configuration...
Current configuration : 209 bytes
interface GigabitEthernet1/0/22
description Trunk to WLC001 DistPort1
switchport trunk encapsulation dot1q
switchport trunk native vlan 254
switchport mode trunk
channel-group 14 mode active
end
sh run int g2/0/22
Building configuration...
Current configuration : 209 bytes
interface GigabitEthernet2/0/22
description Trunk to WLC001 DistPort2
switchport trunk encapsulation dot1q
switchport trunk native vlan 254
switchport mode trunk
channel-group 14 mode active
end -
WLC 5508 and LAP1310 - Not syncing up!
As the title states I have a WLC 5508 and a LAP1310 that will not sync up.
The error stated in the traps log is "AP with MAC (xxxx.xxxx.xxxx.xxxx) is unknown."
WLC software release is : 7.2.103.0
IOS on the AP is : 12.4(18a)JA2
Upon some investigation I found that the "AP with MAC is unknown" error usually points to one of two things:
A. WLC firmware needs to be updated
B. AP needs to be updated.
C. The AP is not compatible with the WLC.
I am leaning toward solution C and I am looking for a conformation or a correction, if anyone could help out that would be greatly appreciated!
I've tried reading the compatibility matrix released by Cisco, but I found it mildly confusing as to what is and isn't supported by each software release.
Sources - http://www.cisco.com/en/US/products/ps6366/products_tech_note09186a00808f8599.shtml#lap1250
Problem 11: 1250 LAP Not Able to Join WLC
The setup consists of a 2106 WLC that runs version 4.1.185.0. A Cisco 1250 AP is not able to join the controller.
The log on the WLC shows this:
Mon Jun 2 21:19:37 2008 AP with MAC f0:2x:cf:2x:1d:3x (APf02x.cf2x.1d3x) is unknown.
Mon Jun 2 21:19:37 2008 AP Associated. Base Radio MAC: f0:2x:cf:2x:1d:3x
Mon Jun 2 21:19:26 2008 AP Disassociated. Base Radio MAC:f0:2x:cf:2x:1d:3x
Mon Jun 2 21:19:20 2008 AP with MAC f0:2x:cf:2x:1d:3x (APf02x.cf2x.1d3x) is unknown.
Mon Jun 2 21:19:20 2008 AP Associated. Base Radio MAC: f0:2x:cf:2x:1d:3x
Mon Jun 2 21:19:09 2008 AP Disassociated. Base Radio MAC:f0:2x:cf:2x:1d:3x
Mon Jun 2 21:19:03 2008 AP with MAC f0:2x:cf:2x:1d:3x (APf02x.cf2x.1d3x) is unknown.
Solution: This is because the Cisco 1250 series LAP is not supported on version 4.1. The Cisco Aironet 1250 Series AP is supported from controller versions 4.2.61 and later. In order to fix this issue, upgrade the controller software to 4.2.61.0 or later.
Problem 16: 1000 series LAPs not able to join the Wireless LAN controller, WLC runs version 5.0
This is because WLC software release 5.0.148.0 or later is not compatible with Cisco Aironet 1000 series APs. If you have a Cisco 1000 series LAP in a network, which runs WLC versions 5.0.48.0, the 1000 series LAP does not join the controller and you see this trap message on the WLC.
"AP with MAC xx:xx:xx:xx:xx:xx is unkown"videoaudiojack
What version of Premiere Elements are you using and on what computer operating system is it running?
What are the properties of this .mp4 video import (video and audio compressions, frame size, frame rate, interlaced or progressive, pixel aspect ratio)?
If you have any information about the video bitrate and audio bitrate of the file, that would be good to know.
What is the audio - stereo 2 channel or 5.1 channel?
What are you (manually) or the project automatically setting as the project preset to match the properties of your source video?
Let us start here and then decide what next.
Thank you.
ATR -
An issue with WLC 5508 and 7921 phone
Hello all!
I have a system with WLC 5508 and some 1242 APs. And I use a lot of 7921 phones.
One of 7921 phones was in trouble. It loses registration, disconnect conversations...
I installed the trial WLC and run voice diagnostics.
I saw some of "Potentially degraded QoS in downlink direction because of incorrect packet classification" messages and one "Fair upstream packet loss ratio: 1,2%, which is less than threshold 2.5%"
As I understand all of 7921 phones in these area are affected.
what does it mean? I set up Platinum QoS for voice WLAN. I don't have any qos configuration string for AP and WLC ports on switches...
any ideas?
thanx in advanceSergey:
There is one application called "WLC Config analyzer". You save your "show run-config" from your WLC in a text file and import it by this application. it will analyze the file for you and tell you what recommendations for voice are missing so you improve them.
When importing a config file you choose what voice clinets you are using, so you need to choose cisco 7921 to it tells you what config improvemetns is needed based on 7921 needs.
Here is the link to download the application:
https://supportforums.cisco.com/docs/DOC-1373
download the latest versoin.
BTW, how many voice/data clients are connected to one AP in that area? if I remember correctly if you are utilizing voice then the max number of clients connected to one AP should not exceed 17. If you have more than this number per AP try to minimize the number of users concurrently connected to the AP then try again.
Hope you'll find the config analyzer useful.
If useful please don't forget to rate.
Amjad -
WLC 5508 and remote site (DMVPN) Access Points
Hi All,
We just purchased a WLC 5508 and would like to know if it will control remote VPN site Access Points. Here are the details:
The 5508 will live at our home office. We have multiple remote sites that are connected via Cisco's DMVPN. Each site has one Cisco 1131 Access Point hanging off of either a Cisco 1841 or a 2811 that is using DMVPN back to the home office 2811. Can the 5508 manage the remote Access Points?
Thanks for your help guys!Are you are talking about OfficeExtend?
Cisco OfficeExtend
https://www.cisco.com/en/US/solutions/collateral/ns340/ns517/ns430/solution_overview_c22-523307_ns348_Networking_Solution_Solution_Overview.html
OfficeExtend supports 1130 & 1140 as long as you have the Wireless PLUS (WPLUS) Software.
OfficeExtend Access Point
http://www.cisco.com/en/US/docs/wireless/wcs/6.0/configuration/guide/6_0apcfg.html#wp1069890 -
Hi,
I have a problem with a poor signal. I have two WLC 5508 and 10 ap's 3502. So, that I have two wlc on the network I decided to divide this 10 ap's.
WLC 5508 has 7.0.98 software version.
The 5 first ap was associated to one wlc and the other 5 to second controller.
Two problems was observed, first that some clients which try connect to AP associated to second controller have problem to obtain IP address from DHCP pool on first wlc.
The second problem is that on this two WLC was configured two DHCP pool. One controller assigns address for a dedicated WLAN and the second wlc assigns address for a second WLAN.
This two WLAN's is broadcast on two wlc.
KamilHi Nicolas,
The APs are 3502I model and now are located on the lower ceiling.
From Thursday all APs are associated to only one WLC the second one is just only as a backup and from this time there are not any problems with a signal. This information is directly from clients.
The DHCP pool is located on the first WLC now.
Also, I considered to use switch or other machine as a DHCP pool but it's problematic to deploy now.
Kamil -
Wlc 5508 and 40 access point 1141n disturbance in the temp response
Hello,
i have a wlc 5508 and 40 access point 1141n
there are 1500 users connected with this controller 5508.
but when i ping at my gateway ,there is a disturbance in the temp response .
Here below a snapshot:
Réponse de 172.16.1.1 : octets=32 temps=1 ms TTL=55
Réponse de 172.16.1.1 : octets=32 temps=5 ms TTL=55
Réponse de 172.16.1.1 : octets=32 temps=2 ms TTL=55
Réponse de 172.16.1.1 : octets=32 temps=56 ms TTL=55
Réponse de 172.16.1.1 : octets=32 temps=105 ms TTL=55
Réponse de 172.16.1.1 : octets=32 temps=433 ms TTL=55
Réponse de 172.16.1.1 : octets=32 temps=1 ms TTL=55
Réponse de 172.16.1.1 : octets=32 temps=100 ms TTL=55
Réponse de 172.16.1.1 : octets=32 temps=300 ms TTL=55
Réponse de 172.16.1.1 : octets=32 temps=466 ms TTL=55
Réponse de 172.16.1.1 : octets=32 temps=711 ms TTL=55
Réponse de 172.16.1.1 : octets=32 temps=900 ms TTL=55
Réponse de 172.16.1.1 : octets=32 temps=55 ms TTL=55
Réponse de 172.16.1.1 : octets=32 temps=52 ms TTL=55
Réponse de 172.16.1.1 : octets=32 temps=54 ms TTL=55
Réponse de 172.16.1.1 : octets=32 temps=200 ms TTL=55
Réponse de 172.16.1.1 : octets=32 temps=57 ms TTL=55
Réponse de 172.16.1.1: octets=32 temps=800 ms TTL=55
anyone help me?
thxLooks to be wither a duplicate address issue or a configuration issue. Try to test with only using the 2.4ghz and then again with only the 5ghz and see if you see a difference.
Thanks,
Scott
Help out other by using the rating system and marking answered questions as "Answered" -
WLC 5508 And Third Party SSL for Web Authenticaiton
Hello,
We are using WLC 5508 and currently the authentication process is via Customized WebAuth. As you know that with the WebAuth the authentication process won't work unless you launch Web Browser and you will be redirected to the Authentication Page where you type your username and password. This is a bit fuzzy for most of the users and what I'm thinking is to use different authentication mechanism where the user will automatically be prompted upon connecting to any SSID. I have read that Public/Thrid Party certificate will do this and any client can accept the public certificate.
Anyone can elaborate on this approach?
Regards,With machines that are not part of the domain, typicall if you still want to secure them usin 802.1x, you would leverage a radius server and users would be told of the SSID to connect to and enter their AD credentials. Of course, if you use AD credentials, users will now join all their other devices to that SSID. This is where ISE comes in and you can profile devices. Even though the WLC with v7.6 can profile, it's not a full fledge profiler. Depending on how well you know radius, you can leverage a portal page also and depending on the AD group a user is a member of, you can out them is a specific Vlan or if you leverage interface groups. You can do many things, but you need to really know radius and client types to figure out what can and work well in your environment. Radius alone to someone who hasn't played with it, can take days to setup without help.
Every client I setup radius for is different and it comes down to how their users are setup in AD, what devices they have and the requirements.
Scott -
WLC 5508 AND AP 1141N disturbance in the temp response
i have a wlc 5508 and 40 access point 1141n
there are 1500 users connected with this controller 5508.
but when i ping at my gateway ,there is a disturbance in the temp response .
Here below a snapshot:
Réponse de 172.16.1.1 : octets=32 temps=1 ms TTL=55
Réponse de 172.16.1.1 : octets=32 temps=5 ms TTL=55
Réponse de 172.16.1.1 : octets=32 temps=2 ms TTL=55
Réponse de 172.16.1.1 : octets=32 temps=56 ms TTL=55
Réponse de 172.16.1.1 : octets=32 temps=105 ms TTL=55
Réponse de 172.16.1.1 : octets=32 temps=433 ms TTL=55
Réponse de 172.16.1.1 : octets=32 temps=1 ms TTL=55
Réponse de 172.16.1.1 : octets=32 temps=100 ms TTL=55
Réponse de 172.16.1.1 : octets=32 temps=300 ms TTL=55
Réponse de 172.16.1.1 : octets=32 temps=466 ms TTL=55
Réponse de 172.16.1.1 : octets=32 temps=711 ms TTL=55
Réponse de 172.16.1.1 : octets=32 temps=900 ms TTL=55
Réponse de 172.16.1.1 : octets=32 temps=55 ms TTL=55
Réponse de 172.16.1.1 : octets=32 temps=52 ms TTL=55
Réponse de 172.16.1.1 : octets=32 temps=54 ms TTL=55
Réponse de 172.16.1.1 : octets=32 temps=200 ms TTL=55
Réponse de 172.16.1.1 : octets=32 temps=57 ms TTL=55
Réponse de 172.16.1.1: octets=32 temps=800 ms TTL=55
anyone help me
THXLooks to be wither a duplicate address issue or a configuration issue. Try to test with only using the 2.4ghz and then again with only the 5ghz and see if you see a difference.
Thanks,
Scott
Help out other by using the rating system and marking answered questions as "Answered" -
Integration between WLC 5508 and Microsoft NPS 2008
Hi guys,
Any of you, have working guidance for WLC 5508 and Microsoft NPS 2008 integration?
I managed to configure Wireless 802.1x feature (PEAP) but it failed. I'm running software ver. 7.0.116.0.
Is there any bug related 802.1x on this software version?
thanks in advance.
BR
shendyHi Shendy,
I am not aware about any bug related to this. I think you better check all configuration and make sure it is fine.
Logs from NPS and WLC (and possibly from the supplicant) may guide you where the problem resides.
What does the NPS logs tell about the reason of the authentication failure?
What does the WLC logs say about the failure (check show msglog and show traplog).
- Make sure the Radius server added correctly with correct IP and correct shared secret on WLC.
- Make sure that the radius is configured correctly to allow PEAP-MSCHAPv2.
- Make sure WLC is added successfully to WLC with correct IP address and correct shared secret.
- Make sure the clients are correctly configured and the server's (NPS) certificate is trusted on the clients.
HTH
Amjad -
What is the spec of WLC 5508 and 4402, CPU and MEM? Thanks.
I cant found any information about WLC 5508 and 4402s' spec of what type of CPU and size of MEM. Thanks.
4402 is having 512MB memory where as 5508 is having 1GB (based on "show memory statistics" output)
Also during bootup it will show (here is 4402 as example)
System will now restart!
Bootloader 7.0.116.0 (Apr 13 2011 - 14:30:45)
Motorola PowerPC ProcessorID=00000000 Rev. PVR=80200020
CPU: 833 MHz
CCB: 333 MHz
DDR: 166 MHz
LBC: 41 MHz
L1 D-cache 32KB, L1 I-cache 32KB enabled.
I2C: ready
DTT: 1 is 33 C
DRAM: DDR module detected, total size:512MB.
512 MB
8540 in PCI Host Mode.
8540 is the PCI Arbiter.
Memory Test PASS
FLASH:
Flash Bank 0: portsize = 2, size = 8 MB in 142 Sectors
8 MB
L2 cache enabled: 256KB
Card Id: 1540
Card Revision Id: 1
Card CPU Id: 1287
Number of MAC Addresses: 32
Number of Slots Supported: 4
Serial Number: FOC1229F08U
Unknown command Id: 0xa5
Unknown command Id: 0xa4
Unknown command Id: 0xa3
Manufacturers ID: 30464
Board Maintenance Level: 00
Number of supported APs: 12
In: serial
Out: serial
Err: serial
HTH
Rasika
**** Pls rate all useful responses **** -
Hello,
We've got a problem with the AP (AIR CAP 1602I) which is managed by WLC 5508(7.4.100.60)
Users connect to the AP with VOIP phones(Avaya).. and there are following problems during calls
-robot voice
-strong noise(even if call is not made, just speaker is on)
Strange thing is that there is no problem with older APs which are managed with the same WLC.
Any idea?
Thanks in advanceWell that can be a cause also. I would look at using 7.4.110.0 which is MR1. If that doesn't help, then open a TAC case as it might be something else. Going to v7.5 I don't think will fix the issue.
Many times I would go the the manufacture and find out if the support a certain code or not. It's nice when they do test to make sure it still works. Some manufactures do test and will suggest code versions and that's when you have to decide if the 1602 was really needed or just keep adding 1262's since there was only 3 added.
Sent from Cisco Technical Support iPhone App -
Hi Fellows,
I wanna know if 5508 Cisco WLC support LACP or not. Actually i work in a project where i must
connect WLC 5508 in Enterasys Switches with Link Aggregation.
Enterasys Switches support LACP 802.3ad but when i learn Cisco Books i see that WLC 5508
doesn't support LACP.
Can you help please ?
Sincerely
JosephHi,
Please take a look into the config guide:
http://www.cisco.com/en/US/docs/wireless/controller/7.0/configuration/guide/c70mint.html#wp1277652.
You can read there:
Once the EtherChannel is configured as on at both ends of the link, it does not matter if the Catalyst switch is configured for either Link Aggregation Control Protocol (LACP) or Cisco proprietary Port Aggregation Protocol (PAgP) because no channel negotiation is done between the controller and the switch. Additionally, LACP and PAgP are not supported on the controller.
HTH,
Tiago
If this helps you and/or answers your question please mark the question as "answered" and/or rate it, so other users can easily find it. -
Hi everyone!
Question is simple, but I cannot find it in google.
Does WLC 5508 support AIR-LAP1042N?
Reagrds,
AlekseiOne more question.
What poe injector is supported on AIR-LAP1042N?
I have found poe injectors for other APs.
1.AIR-PWR-B=
2.AIR-PWRINJ4
Will anyone of these support this AP? -
Hello,
i'm tryin to install a WLC 5508 with version 7.6.120 and with AP 2702i with the follwing firmware ap3g2-rcvk9w8-xx ( 15.2(4)JB5), i've configured saticly the capwapp with the follwwing configuration:
IP Address 172.17.255.234
IP netmask 255.255.0.0
Default Gateway 172.17.255.254
Primary Controller 172.17.255.239
The controller iw the IP 172.17.255.239 and i've connectivity between the both equipments, there's no firewalls between them, however i can't register the AP with the controller, anyone have some idea?Hi,
May be AP comes with mesh image: You cans ee in logs
If it is with mesh image then use this:
1. Log into your Wireless LAN Controller.
Select the Security tab.
Expand AAA and select AP Policies.
Click the Add button in the far right.
Under Add AP to Authorization List, enter the MAC Address of the Access Point in the MAC Address text box.
Click the Add button.
Click the Apply button
Now your AP must be in downloding state.
2. When the AP finally show up under the Wireless tab, check the AP Mode . It may operating in ‘Bridge’ mode. This is incorrect. It should be in ‘Local’ mode.
If your AP is in ‘Bridge’click the name of the AP under the AP Name column. Under the General tab, click the AP Mode drop down box and select ‘Local’. Click the Apply button in the top right.
Now AP should now be working fine.
Hope it helps.
Regards
Dont forget to rate helpful posts
Maybe you are looking for
-
In an Excel template file, can I set the Folder Path in the SaveAs Dialog box?
I have an Excel template file (xltm) and, with help from the forum, I now have a Workbook_BeforeSave subroutine to save the template as a macro enabled file (xlsm). I'm so thankful for that help from Edward in the forum. I also want to set the defau
-
How to edit/update data into an XML file using Flex and Actionscript
I can read an external xml file, please see the code below: protected function button1_clickHandler(event:MouseEvent):void var GrowthChartsDataGrid:XML; var loader:URLLoader = new URLLoader(); var request:URLRequest = new URLRequest("../GrowthChartsD
-
Best practice for developing and testing AIR iOS multitouch apps
I'm considering switching our iPhone development practice from XCode/Objective C to AIR to leverage a larger pool of in house talent. The biggest concern I have right now is testing multitouch functionality - the prospect of having to do incremental
-
Consolas hyphen problem in PDFs
Here's the setup: FrameMaker 7.2, Windows XP, Acrobat Pro 8.1.3, although I think all versions are actually irrelevant to the issue. I recently switched to Consolas font for my code listings. But when Acrobat/Distiller converts the FrameMaker file t
-
My ipod is crap! I hate it!
Hey everyone I was just wondering if someone could help me out with my ipod. It displays the message that it needs to be restored using itunes but when i try to restore it, it won't work. itunes tells me that an unknown error has occured or that the