WLC 5508 / firmware 7.2.110.0 is restarting automatically ( COLD START )
Hi Experts ,
I am having weird issue with 5508 controller which is having firmware 7.2.110.0 . This controller is restarting automatically
Since this issue was occuring since long time with earlier version , I have upgraded to 7.2.110.0 , however still no luck ....
I do not have any logs related to controller crash info.
Hey Scott,
I'm about to upgrade a 5508 controller from 7.0.220.0 to 7.4.110.0 , and was just prepping myself on upgrading the FUS as it will be the first time. Latest for 5508 is 1.7 and I noticed for 2504 its 1.8.
I was just curious where you saw that its mandatory to upgrade the FUS ? I can't seem to locate any actual documentation specifying anything about upgrading the FUS when going from one version to another etc. I know one of my clients has a 5508 on 7.4 with the old FUS (see below).
Bootloader Version............................... 1.0.1Field Recovery Image Version..................... 6.0.182.0
Firmware Version................................. FPGA 1.3, Env 1.6, USB console 1.27
Build Type....................................... DATA + WPS
Looking forward to your reply
Thanks !
Similar Messages
-
WLC 5508 running 7.4.110.0 unable to tftp upload config from controller
Hi,
Two WLC 5508 running identical code version. One is 50 license Primary, the second is HA. Identical config on both. HA WLC can upload its config to the TFTP or FTP server but Primary cannot. The operation fails for both CLI and GUI and for different protocols i.e. TFTP, FTP.
#### Primary Controller
(Cisco Controller) >show sysinfo
Manufacturer's Name.............................. Cisco Systems Inc.
Product Name..................................... Cisco Controller
Product Version.................................. 7.4.110.0
Bootloader Version............................... 1.0.20
Field Recovery Image Version..................... 7.6.95.16
Firmware Version................................. FPGA 1.7, Env 1.8, USB console 2.2
Build Type....................................... DATA + WPS
System Name...................................... PRODWC7309
System Location..................................
System Contact...................................
System ObjectID.................................. 1.3.6.1.4.1.9.1.1069
Redundancy Mode.................................. Disabled
IP Address....................................... 10.1.30.210
Last Reset....................................... Power on reset
System Up Time................................... 18 days 18 hrs 51 mins 35 secs
System Timezone Location......................... (GMT+10:00) Sydney, Melbourne, Canberra
System Stats Realtime Interval................... 5
System Stats Normal Interval..................... 180
Configured Country............................... AU - Australia
Operating Environment............................ Commercial (0 to 40 C)
--More-- or (q)uit
Internal Temp Alarm Limits....................... 0 to 65 C
Internal Temperature............................. +34 C
External Temperature............................. +17 C
Fan Status....................................... OK
State of 802.11b Network......................... Enabled
State of 802.11a Network......................... Enabled
Number of WLANs.................................. 8
Number of Active Clients......................... 138
Memory Current Usage............................. Unknown
Memory Average Usage............................. Unknown
CPU Current Usage................................ Unknown
CPU Average Usage................................ Unknown
Burned-in MAC Address............................ 3C:08:F6:CA:52:20
Power Supply 1................................... Present, OK
Power Supply 2................................... Present, OK
Maximum number of APs supported.................. 50
(Cisco Controller) >debug transfer trace enable
(Cisco Controller) >transfer upload start
Mode............................................. TFTP
TFTP Server IP................................... 10.1.22.2
TFTP Path........................................ /
TFTP Filename.................................... PRODWC7309-tmp.cfg
Data Type........................................ Config File
Encryption....................................... Disabled
*** WARNING: Config File Encryption Disabled ***
Are you sure you want to start? (y/N) Y
*TransferTask: Jun 02 10:41:15.183: Memory overcommit policy changed from 0 to 1
*TransferTask: Jun 02 10:41:15.183: RESULT_STRING: TFTP Config transfer starting.
TFTP Config transfer starting.
*TransferTask: Jun 02 10:41:15.183: RESULT_CODE:1
*TransferTask: Jun 02 10:41:24.309: Locking tftp semaphore, pHost=10.1.22.2 pFilename=/PRODWC7309-tmp.cfg
*TransferTask: Jun 02 10:41:24.393: Semaphore locked, now unlocking, pHost=10.1.22.2 pFilename=/PRODWC7309-tmp.cfg
*TransferTask: Jun 02 10:41:24.393: Semaphore successfully unlocked, pHost=10.1.22.2 pFilename=/PRODWC7309-tmp.cfg
*TransferTask: Jun 02 10:41:24.394: tftp rc=-1, pHost=10.1.22.2 pFilename=/PRODWC7309-tmp.cfg
pLocalFilename=/mnt/application/xml/clis/clifile
*TransferTask: Jun 02 10:41:24.394: RESULT_STRING: % Error: Config file transfer failed - Unknown error - refer to log
*TransferTask: Jun 02 10:41:24.394: RESULT_CODE:12
*TransferTask: Jun 02 10:41:24.394: Memory overcommit policy restored from 1 to 0
% Error: Config file transfer failed - Unknown error - refer to log
(Cisco Controller) >show logging
*TransferTask: Jun 02 10:41:24.393: #UPDATE-3-FILE_OPEN_FAIL: updcode.c:4579 Failed to open file /mnt/application/xml/clis/clifile.
*sshpmReceiveTask: Jun 02 10:41:24.315: #OSAPI-3-MUTEX_FREE_INFO: osapi_sem.c:1087 Sema 0x2b32def8 time=142 ulk=1621944 lk=1621802 Locker(sshpmReceiveTask sshpmrecv.c:1662 pc=0x10b07938) unLocker(sshpmReceiveTask sshpmReceiveTaskEntry:1647 pc=0x10b07938)
-Traceback: 0x10af9500 0x1072517c 0x10b07938 0x12020250 0x12080bfc
*TransferTask: Jun 02 10:39:01.789: #UPDATE-3-FILE_OPEN_FAIL: updcode.c:4579 Failed to open file /mnt/application/xml/clis/clifile.
*sshpmReceiveTask: Jun 02 10:39:01.713: #OSAPI-3-MUTEX_FREE_INFO: osapi_sem.c:1087 Sema 0x2b32def8 time=5598 ulk=1621801 lk=1616203 Locker(sshpmReceiveTask sshpmrecv.c:1662 pc=0x10b07938) unLocker(sshpmReceiveTask sshpmReceiveTaskEntry:1647 pc=0x10b07938)
-Traceback: 0x10af9500 0x1072517c 0x10b07938 0x12020250 0x12080bfc
#### HA Controller
(Cisco Controller) >show sysinfo
Manufacturer's Name.............................. Cisco Systems Inc.
Product Name..................................... Cisco Controller
Product Version.................................. 7.4.110.0
Bootloader Version............................... 1.0.20
Field Recovery Image Version..................... 7.6.95.16
Firmware Version................................. FPGA 1.7, Env 1.8, USB console 2.2
Build Type....................................... DATA + WPS
System Name...................................... PRODWC7310
System Location..................................
System Contact...................................
System ObjectID.................................. 1.3.6.1.4.1.9.1.1069
Redundancy Mode.................................. Disabled
IP Address....................................... 10.1.31.210
Last Reset....................................... Software reset
System Up Time................................... 18 days 19 hrs 1 mins 27 secs
System Timezone Location......................... (GMT+10:00) Sydney, Melbourne, Canberra
System Stats Realtime Interval................... 5
System Stats Normal Interval..................... 180
Configured Country............................... AU - Australia
Operating Environment............................ Commercial (0 to 40 C)
--More-- or (q)uit
Internal Temp Alarm Limits....................... 0 to 65 C
Internal Temperature............................. +34 C
External Temperature............................. +17 C
Fan Status....................................... OK
State of 802.11b Network......................... Enabled
State of 802.11a Network......................... Enabled
Number of WLANs.................................. 4
Number of Active Clients......................... 0
Memory Current Usage............................. Unknown
Memory Average Usage............................. Unknown
CPU Current Usage................................ Unknown
CPU Average Usage................................ Unknown
Burned-in MAC Address............................ 3C:08:F6:CA:53:C0
Power Supply 1................................... Present, OK
Power Supply 2................................... Present, OK
Maximum number of APs supported.................. 500
(Cisco Controller) >debug transfer trace enable
(Cisco Controller) >transfer upload start
Mode............................................. FTP
FTP Server IP.................................... 10.1.22.2
FTP Server Port.................................. 21
FTP Path......................................... /
FTP Filename..................................... 10_1_31_210_140602_1050.cfg
FTP Username..................................... ftpuser
FTP Password..................................... *********
Data Type........................................ Config File
Encryption....................................... Disabled
*** WARNING: Config File Encryption Disabled ***
Are you sure you want to start? (y/N) y
*TransferTask: Jun 02 10:51:31.278: Memory overcommit policy changed from 0 to 1
*TransferTask: Jun 02 10:51:31.278: RESULT_STRING: FTP Config transfer starting.
FTP Config transfer starting.
*TransferTask: Jun 02 10:51:31.278: RESULT_CODE:1
*TransferTask: Jun 02 10:52:05.468: ftp operation returns 0
*TransferTask: Jun 02 10:52:05.477: RESULT_STRING: File transfer operation completed successfully.
*TransferTask: Jun 02 10:52:05.477: RESULT_CODE:11
File transfer operation completed successfully.
Not upgrading to 7.4.121.0 because of bug CSCuo63103. Have not restarted the controller yet.
Any one else had this issue ? Is there a workaround ?
Thanks,
Rick.Thanks Stephen, In my deployments of 7.4.110.0 version I have not seen this issue so may be controller reboot will fix it (we do have HA to minimize the impact). I will keep the thread updated with findings and may request TAC for the special release 7.4.121.0 if the still not happy with 7.4.110.0
Rick. -
Migrating AP's from WLC 4400 v.4.0.179.11 to WLC 5508 v.7.2.110.0
Hi,
I am replacing an old 4400 series WLC running version 4.0.179.11 to a new 5508 WLC running version 7.2.110.0.
We currently have 70 x 1131 Access points on the 4400 WLC.
With this upgrade, do i need to upgrade the old 4400 to version 6.0 so the AP's get an up to date IOS or can i directly migrate all AP's over to the new 5508 without any version incompatabilities on the AP's?
I am abit worried that the AP's are running a very old IOS on the 4400 v.4.0.179.11 to go straight to the new 5508 v.7.2.110.0.
ThanksHi,
Check out this release note
http://www.cisco.com/en/US/docs/wireless/controller/release/notes/crn7_2_110_0.html#wp976667
You'll need to get up to a supported version of 6.0 first as per the release notes.
You'll need to check out the 6.0 release notes too to make sure there are no other intermediate upgrade steps required too.
Nigel
Sent from Cisco Technical Support iPad App -
Hi All,
WLC 5508 - current firmware 7.0.116.0 is running on it. we need add couple of 2700 series AP. From the release notes i got know 2700 series supported on the 7.6.120.x and later.
http://www.cisco.com/c/en/us/td/docs/wireless/access_point/2700/quick/guide/ap2700getstart.html
- whereas 7.6.120.x is the latest one in the train. can we have this firmware on the controller as its latest??
- from the release notes - we can have a direct upgrade to 7.6.120.0., upgrading from 7.0.x.x to 7.6.120.x missing so many version in between. any potential problems i may get ??
- FUS (Field upgrade software is necessary) which version and how it can be installed ??
Regards,
ChannaHi Channa,
Go for the 7.6.130.0 (7.6MR3) when it is available to public. To be released within next couple of weeks.If you need to do this before 7.6MR3 comes then you can get pre-release of that code via TAC. Refer below for that.
https://supportforums.cisco.com/document/12245186/76mr3-beta-availability
Yes, you have to upgrade your FUS, It is recommended to go for v 1.9.0.0. Below will give you the upgrade procedure. Better to do it via CLI & allocate 30-45min downtime for this upgrade
http://www.cisco.com/c/en/us/td/docs/wireless/controller/release/notes/fus_rn_OL-31390-01.html
Feature wise there are lots of feature available in 7.6.x compare to 7.0.x. But I do not expect any problem going from 7.0.x to 7.6.x as long as you upgrade your FUS first.
Also read these compatibility matrix to see all your AP models are supporting by this 7.6.x code & any other PI or MSE compatibility if you have those.
http://www.cisco.com/c/en/us/td/docs/wireless/compatibility/matrix/compatibility-matrix.html
HTH
Rasika
**** Pls rate all useful responses **** -
WLC 5508 and 7.4.110.0 and AP Blackhole?
So large customer had WLCs running 7.4.110.0 and it appears there was either a 3500/3600 AP memory leak or a CCKM roaming issue. The APs would occasionally blackhole traffic. You could see 2+ APs at -67dbm in 5GHz. Phones are locked to 5GHz, data rates matched. . Phone showed good strong signal, but 7925 users would report every couple days the phone dropping/DHCP timeout, re-registering, etc. We had a large CSE/TAC group onsite audit the 7925 Deployment Guide and setup, and we did a lot of cleanup but never hit the silver bullet.
After upgrading the 5508 to 7.4.121.4 (TAC special not on Cisco.com) they reported the 7925 problems have improved. Only been 1 day so far.
There is also a WPA2 with Preshared Key CCKM bug with the 7925s that roaming takes 2s. Use either strong WEP or buy 7926s, or use EAP/certificates, etc. https://tools.cisco.com/bugsearch/bug/CSCtt38270
7.4.121.0 Release Notes
http://www.cisco.com/c/en/us/td/docs/wireless/controller/release/notes/crn74mr02.html#wp1142453
We are running daily Traffic Stream Metrics (TSM) reports from Prime/WLC, and exporting the CallManager Diagnositc LQK records (export via CAR) to show if things are improving/etc.Thanks Stephen, In my deployments of 7.4.110.0 version I have not seen this issue so may be controller reboot will fix it (we do have HA to minimize the impact). I will keep the thread updated with findings and may request TAC for the special release 7.4.121.0 if the still not happy with 7.4.110.0
Rick. -
ISE 1.3 not receiving Radius requests from WLC 5508 ver 8.0.110.0
Hello all. I just implemented ISE 1.3 at a customer site. added a WLC running 8.0.110.0 using its mgmt address with a RADIUS preshared key. On the WLC, I created to SSIDs, corp and guest.
For corp I configured WPA2 and AES and forwarded Radius requests to my 2 ISE node PSN interfaces
For the guest I configured MAC filter with advanced features AAA overide and Radius NAC - per Cisco's documents
The corp forwards Radius requests to ISE, the guest does not. I get nothing from the guest.
I configured the WLC step by step from the Cisco document. I have completed over 10 ISE implementations in the last year using ISE 1.2 and WLC 7.x and have never run into this issue before.
Any help will be much appreciated.This issue has been resolved. The issue was that for the guest SSID MAC filtering was enabled as required, but they had the test PCs on a mac filter bypass list for that SSID in the WLC. This was automatically authenticating the PC, and therefore not forwarding the RADIUS to ISE.
Once we removed the PC from the MAC filter list in the WLC, the authentications were forwarded to ISE as desired. -
Unable to add SNMP server in WLC 5508 with 7.4.110
hi
I am trying to add 0.0.0.0/0 as SNMP address and netmask and i am getting an error saying the netmask is invalid.
is there a different way to set this?Hi Roy,
This is strange.
I do not have a test WLC with this code to test, but command syntax is correct. I have verified it on my test controller in 7.0.116.0 & it is happy to accept it. Even 7.4 config guides does not show any other command syntax for this.
http://www.cisco.com/en/US/docs/wireless/controller/7.4/configuration/guides/consolidated/b_cg74_CONSOLIDATED_chapter_0111.html
One good thing is, this is the default setting once you create a snmp-community. It should have 0.0.0.0/0 as subnet/net mask & you do not require any changes for the default config.
"show snmpcommunity" output should show the config values for your SNMP community.
If you are trying to change it from configured subnet to default value, then as a work around you can re-create the snmp commnuity from fresh (delete & recreate)
If you have Cisco TAC assistance then log a case with them to see why this command is not accepting in your code of WLC
HTH
Rasika
**** Pls rate all useful responses **** -
Is there anywhere that shows the main differences / feature sets between the 7.2, 7.3 and 7.4 firmware? Are there any general recommendations?
TIASecond Scott.
http://www.cisco.com/en/US/products/ps10315/prod_release_notes_list.html
If you look at each release note, there is a section called "What's New in this release" that can provide a good brief overview of any additional features/changes with the specific release. -
Trying to get home sharing working on a corporate wireless network. Cisco wireless.
WLC5508 controller
Cisco 3502 access points
All apple devices on same WLAN - security WPA2-PSK
ITunes account up to date
All devices laterst software.
Can ping apll tv from laptop
can ping apple tv from ipad
Can ping ipad from laptop
can ping laptop from ipad.
Apple tv never sees any other device.
Any ideas?Fascinating just reading about your setup. I have a WRT350N and have noticed that it will drop its speed, sometimes down to 1Mbps. It seems to do so at about the same time every day, but usually comes back to speed in about 5 minutes. In my experience, the Apple TV will disconnect if the speed falls this low. Try monitoring the Linksys with Netstumbler, Vistumbler, or just in the Windows Network utility.
Check the "lease obtained" and "lease expired" times for your router to see if that is when the network fails. I've just finished reading an angry thread over at the Linksys forum about the WRT330N where someone mentioned that the router wasn't renewing its lease.
"I cannot set it run off automatic DHCP from the WRT330N, the router will not assign it an IP every time the lease expires, causing me to have to manually set an IP on the Print server. That's annoying. Having the router drop IP's to individual machines after 12-48 hours...very annoying."
http://forums.linksys.com/linksys/board/message?board.id=Wireless_Routers&thread .id=67412
If that is the problem, then I would consider setting up a Static IP address for your Apple TV. You can do that through the user interface -> Settings -> Network -> Configure ... (Quite intuitive as you only have change IP address and the subsequent details remain the same.)
My router assigns IP Addresses in the ranges of 192.168.1.100 ->149. The idea here is to choose an address outside of that range but is not greater than 192.168.1.253 (and should not end in the number 1). You shouldn't have to change the linksys router as long as 50 clients are assigned in that range. You'll have to figure that out by accessing your router webpage at browser address 192.168.1.1 -> the default password is "admin" (without the quotes).
Good luck. -
Incompatibility issue - WLC 5508 and ACS 5.4
Hi,
This is my scenario:
Cisco WLC 5508 firmware 7.4.110.20 and ACS 5.4, two WLAN eap/tls, many client can't connect to WLAN and on ACS i receive the following error:
Authentication failed : 11051 RADIUS packet contains invalid state attribute
workaround:
1 -Check the network device or AAA Client for hardware problems.
2-known RADIUS compatibility issues.
3-Check the network that connects the device to ACS for hardware problems
there are some incompatibility issue between WLC and ACS ? the compatibility matrix document for wireless imposes the 7.5 firmware for WLC.
What do you think is possibile ?Are there any other errors shown in the details of the failed authentication?
We may need to look at service logs in debug mode, opening a TAC case would be the best way to go about this.
Javier Henderson
Cisco Systems -
WLC 5508 - Error When Uploading Webauth Bundle
Currently have a WLC 5508 running 7.4.110.0. I'm trying to upload (download) a webauth bundle to the controller from the web interface and am getting an error. I've tried using FTP, SFTP and TFTP and get a different error with each. When I started out with this, I was using a modified login.tar. Thinking this was the problem, I switched to using the login.tar file included with the Web Authentication Bundle version 1.0.2 downloaded from the Cisco site. This file fails with the errors below. Does anyone have suggestions as to what I'm doing wrong? Is this is a known bug in this version of the software? Thanks!
For FTP:
The web interface shows:
% Error: Webauth Bundle file transfer failed - Unknown error - refer to log.
Log on the controller shows:
*TransferTask: May 28 13:51:12.942: #UPDATE-3-FTP_TRANSFER_FAIL: updcode.c:5631
Error FTP file Transfer [ftp_get], <30>, Read-only file system.
For SFTP:
The web interface shows:
% Error: Webauth Bundle file transfer failed - Unknown error - refer to log.
Log on the controller shows:
*TransferTask: May 28 14:52:58.779: #UPDATE-3-SFTP_TRANSFER_FAIL: updcode.c:5869
Error SFTP file Transfer [sftp_get], <11>, Resource temporarily unavailable.
For TFTP:
The web interface shows:
% Error: Webauth Bundle file transfer failed - Unknown error - refer to log.
Log on the controller shows:
*TransferTask: May 28 15:02:39.232: #UPDATE-3-FILE_OPEN_FAIL: updcode.c:4593 Fai
led to open file webauth.tar.
*sshpmReceiveTask: May 28 15:02:39.153: #OSAPI-3-MUTEX_FREE_INFO: osapi_sem.c:10
87 Sema 0x2b32def8 time=11504 ulk=18587678 lk=18576174 Locker(sshpmReceiveTask s
shpmrecv.c:1662 pc=0x10b07938) unLocker(sshpmReceiveTask sshpmReceiveTaskEntry:1
647 pc=0x10b079Hi,
1. Did you used PIcozip to compress your webauth bundle?
2. Did you try only with one laptop , if yes then try to use other one.
3. Just try to upload default webauth bundl from cisco to wlc and show the result to us.
7.4.121.0 is very stable version.
Regards -
WLC 5508 with AD, NPS but without GPO, how?
Hi,
I didn't found anything related to what I'm trying to do so I though I would create a new discussion...
I would like to setup a new WLAN and to be able to connect, a user will have to enter his username/password that will be confirmed using NPS and Active Directory. The problem is, I don't want to use a GPO, I would like to only verify if the user is a member of a AD group, let's say "wlan_access".
I don't want to install anything ( certificate, GPO, creating a WLAN configuration ) on the user's PC/laptop, only AD validation using NPS as a Radius server.
If a user is part of that AD group, after he enter his credential he will have access to that WLAN.
Is it possible to setup that? How should I configured the WLAN in my WLC 5508 ( running 7.2.110.0 )? How should I configure NPS ( Windows 2008 R2 Enterprise )?
Thanks a lot for your help and answers.
GuillaumeHi guys,
With the info Stephen Rodriguez gave, it looks like I won't be able to do what we want without doing config on the user's devices ( laptop, ipad, etc.. ).
@Joseph Vasanth Louis Yes the message is from the event viewer of the NPS server. In the connection request policies, there's not much config, I let the option "Authentication Methods" in the tab Settings uncheck, so it won't override the settings in the Network Policies.
I though it was possible to have authentication using NPS and Active Directoy without installing anything on the user's devices and still having a secured wireless network ( not like a hotspot ).
The solution I think is the most workable is with the PEAP or PSK, with a certificate but even that...the user will have to create the WLAN profil on his laptop, so I'm not sure we want to go that way. I'll check for the PSK option, to see if the "Web Authentication" could be done using NPS.
Thanks guys for all your time and help. I'll continue my tests and keep you posted. -
Upgrade WLC 5508 Ver. 7.0.98.0 to Ver 7.6.110.0
i will upgrade WLC 5508 Ver 7.0.98.0 with License 50 AP. to Ver 7.6.110.0 will it ask to install license ?
No, It will not ask for again.
Just upgrade the software.
Regards
Dont forget to rate helpful posts -
AIR-CAP1602I-E-K9 Not Talking to WLC 5508
hi all,
can't seem to get my APs to talk to WLC 5508.
can someone advise which WLC firmware to use and where can i get/download (link pls).
currently WLC is running 6.0.199.4.
Mar 1 00:00:47.839: %CDP_PD-4-POWER_OK: All radios disabled - NEGOTIATED inlin
e power source
*Mar 1 00:00:53.931: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does
not have an Ip !!
*Mar 1 00:00:55.963: %DHCP-6-ADDRESS_ASSIGN: Interface BVI1 assigned DHCP addre
ss 172.28.159.15, mask 255.255.255.192, hostname APfc99.47a3.4d22
Translating "CISCO-CAPWAP-CONTROLLER"...domain server (255.255.255.255)
*Mar 1 00:01:06.899: %CAPWAP-3-ERRORLOG: Did not get log server settings from D
HCP.
*Mar 1 00:01:15.899: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-CAPWAP-CONTROL
LER
*Mar 1 00:01:15.899: %CAPWAP-3-ERRORLOG: Discovery response from MWAR 'Cisco_f8
:72:64'running version 6.0.199.4 is rejected. <<<<
APfc99.47a3.4d22>sh ve
Cisco IOS Software, C1600 Software (AP1G2-RCVK9W8-M), Version 15.2(2)JB, RELEASE
SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2012 by Cisco Systems, Inc.
Compiled Tue 11-Dec-12 04:52 by prod_rel_team
ROM: Bootstrap program is C1600 boot loader
BOOTLDR: C1600 Boot Loader (AP1G2-BOOT-M) LoaderVersion 15.2(2)JAX, RELEASE SOFT
WARE (fc1)
APfc99.47a3.4d22 uptime is 11 minutes
System returned to ROM by power-on
System image file is "flash:/ap1g2-rcvk9w8-mx/ap1g2-rcvk9w8-mx"
Last reload reason:
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
[email protected].
cisco AIR-CAP1602I-E-K9 (PowerPC) processor (revision B0) with 98294K/32768K
bytes of memory.
Processor board ID FGL1726W6DQ
PowerPC CPU at 533Mhz, revision number 0x2151
Last reset from power-on
LWAPP image version 7.4.1.37
1 Gigabit Ethernet interface
32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: FC:99:47:A3:4D:22
Part Number : 73-14671-04
PCA Assembly Number : 000-00000-00
PCA Revision Number :
PCB Serial Number : FOC17182J4J
Top Assembly Part Number : 800-38552-01
Top Assembly Serial Number : FGL1726W6DQ
Top Revision Number : A0
Product/Model Number : AIR-CAP1602I-E-K9
Configuration register is 0xFHi,
Date and time is ok on the WLC,
I configured Accept Self Signed Certificate (SSC) under Security / AP policy, once done the WLC recognized the AP, but output from the console of the AP power cycle the access point is:
IOS Bootloader - Starting system.
FLASH CHIP: Micronix MX25L256_35F
Xmodem file system is available.
flashfs[0]: 5 files, 2 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 31936000
flashfs[0]: Bytes used: 6551040
flashfs[0]: Bytes available: 25384960
flashfs[0]: flashfs fsck took 9 seconds.
Reading cookie from SEEPROM
Base Ethernet MAC address: 4c:00:82:9a:47:a3
************* loopback_mode = 0
Loading "flash:/ap1g2-rcvk9w8-mx/ap1g2-rcvk9w8-mx"...####################
File "flash:/ap1g2-rcvk9w8-mx/ap1g2-rcvk9w8-mx" uncompressed and installed, entr
y point: 0x100000
executing...
Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706
Cisco IOS Software, C1600 Software (AP1G2-RCVK9W8-M), Version 15.2(2)JB, RELEASE
SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2012 by Cisco Systems, Inc.
Compiled Tue 11-Dec-12 04:52 by prod_rel_team
Initializing flashfs...
FLASH CHIP: Micronix MX25L256_35F
flashfs[2]: 5 files, 2 directories
flashfs[2]: 0 orphaned files, 0 orphaned directories
flashfs[2]: Total bytes: 31808000
flashfs[2]: Bytes used: 6551040
flashfs[2]: Bytes available: 25256960
flashfs[2]: flashfs fsck took 9 seconds.
flashfs[2]: Initialization complete.
flashfs[3]: 0 files, 1 directories
flashfs[3]: 0 orphaned files, 0 orphaned directories
flashfs[3]: Total bytes: 11999232
flashfs[3]: Bytes used: 1024
flashfs[3]: Bytes available: 11998208
flashfs[3]: flashfs fsck took 1 seconds.
flashfs[3]: Initialization complete....done Initializing flashfs.
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
memory validate-checksum 30
^
% Invalid input detected at '^' marker.
no ip http server
^
% Invalid input detected at '^' marker.
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
login authentication default
^
% Invalid input detected at '^' marker.
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
[email protected].
Warning: the compile-time code checksum does not appear to be present.
cisco AIR-CAP1602I-N-K9 (PowerPC) processor (revision B0) with 98294K/32768K
bytes of memory.
Processor board ID FGL1730S57A
PowerPC CPU at 533Mhz, revision number 0x2151
Last reset from power-on
LWAPP image version 7.4.1.37
1 Gigabit Ethernet interface
32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: 4C:00:82:9A:47:A3
Part Number : 73-14671-04
PCA Assembly Number : 000-00000-00
PCA Revision Number :
PCB Serial Number : FOC17284HL9
Top Assembly Part Number : 800-38552-01
Top Assembly Serial Number : FGL1730S57A
Top Revision Number : A0
Product/Model Number : AIR-CAP1602I-N-K9
% Please define a domain-name first.
logging facility kern
^
% Invalid input detected at '^' marker.
logging trap emergencies
^
% Invalid input detected at '^' marker.
Press RETURN to get started!
*Mar 1 00:00:12.451: %LWAPP-3-CLIENTERRORLOG: Config load from flash failed. In
itialising Cfg
*Mar 1 00:00:13.683: %LINK-6-UPDOWN: Interface GigabitEthernet0, changed state
to up
*Mar 1 00:00:14.687: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEth
ernet0, changed state to up
*Mar 1 00:00:15.123: %SYS-5-RESTART: System restarted --
Cisco IOS Software, C1600 Software (AP1G2-RCVK9W8-M), Version 15.2(2)JB, RELEASE
SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2012 by Cisco Systems, Inc.
Compiled Tue 11-Dec-12 04:52 by prod_rel_team
*Mar 1 00:00:15.151: %LWAPP-3-CLIENTERRORLOG: Config load from flash failed. In
itialising Cfg
*Mar 1 00:00:15.151: %CAPWAP-3-ERRORLOG: Failed to load configuration from flas
h. Resetting to default config
*Mar 1 00:00:16.195: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, chan
ged state to uplwapp_crypto_init: MIC Present and Parsed Successfully
no bridge-group 1 source-learning
^
% Invalid input detected at '^' marker.
%Default route without gateway, if not a point-to-point interface, may impact pe
rformance
*Mar 1 00:00:48.695: %CDP_PD-4-POWER_OK: All radios disabled - INJECTOR_CONFIGU
RED_ON_SOURCE inline power source
*Mar 1 00:00:48.923: %DHCP-6-ADDRESS_ASSIGN: Interface BVI1 assigned DHCP addre
ss 10.2.3.100, mask 255.255.255.0, hostname AP4c00.829a.47a3
Translating "CISCO-CAPWAP-CONTROLLER.campeche.ecosur.mx"...domain server (10.2.3
.10) [OK]
*Mar 1 00:00:59.915: %CAPWAP-3-ERRORLOG: Did not get log server settings from D
HCP.
*Mar 1 00:00:59.919: %CAPWAP-3-ERRORLOG: Dropping dtls packet since session is
not established. A0203E6, 147E, A020364, A47B, 0
*Mar 1 00:01:09.915: %CAPWAP-3-ERRORLOG: Go join a capwap controller
*Jan 29 09:33:18.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_i
p: 10.2.3.230 peer_port: 5246
*Jan 29 09:33:18.535: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully
peer_ip: 10.2.3.230 peer_port: 5246
*Jan 29 09:33:18.535: %CAPWAP-5-SENDJOIN: sending Join Request to 10.2.3.230
*Jan 29 09:33:23.535: %CAPWAP-5-SENDJOIN: sending Join Request to 10.2.3.230
logging facility kern
^
% Invalid input detected at '^' marker.
logging trap emergencies
^
% Invalid input detected at '^' marker.
*Jan 29 09:34:17.999: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 10.
2.3.230:5246
*Jan 29 09:34:17.999: %LWAPP-3-CLIENTERRORLOG: LWAPP LED Init: incorrect led sta
te 255
*Jan 29 09:34:17.999: %LWAPP-3-CLIENTERRORLOG: Config load from flash failed. In
itialising Cfg
*Jan 29 09:34:17.999: %CAPWAP-3-ERRORLOG: Failed to load configuration from flas
h. Resetting to default config
*Jan 29 09:34:28.015: %CAPWAP-3-ERRORLOG: Go join a capwap controller
*Jan 29 09:34:28.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_i
p: 10.2.3.230 peer_port: 5246
*Jan 29 09:34:28.535: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully
peer_ip: 10.2.3.230 peer_port: 5246
*Jan 29 09:34:28.535: %CAPWAP-5-SENDJOIN: sending Join Request to 10.2.3.230
*Jan 29 09:34:33.535: %CAPWAP-5-SENDJOIN: sending Join Request to 10.2.3.230
and debug command output enable CAPWAP events
(Cisco Controller) >debug capwap events enable
(Cisco Controller) >*spamApTask7: Jan 29 03:39:08.092: acDtlsPlumbControlPlaneKeys: lrad:10.2.3.100(42107) mwar:10.2.3.230(5246)
*spamApTask7: Jan 29 03:39:08.093: 4c:00:82:9a:47:a0 DTLS keys for Control Plane deleted successfully for AP 10.2.3.100
*spamApTask7: Jan 29 03:39:08.100: 4c:00:82:9a:47:a0 DTLS connection closed event receivedserver (10.2.3.230/5246) client (10.2.3.100/42107)
*spamApTask7: Jan 29 03:39:08.100: 4c:00:82:9a:47:a0 Entry exists for AP (10.2.3.100/42107)
*spamApTask7: Jan 29 03:39:08.100: 4c:00:82:9a:47:a0 No AP entry exist in temporary database for 10.2.3.100:42107
*spamApTask7: Jan 29 03:39:08.104: 4c:00:82:9a:47:a0 Discovery Request from 10.2.3.100:42107
*spamApTask7: Jan 29 03:39:08.104: 4c:00:82:9a:47:a0 Join Priority Processing status = 0, Incoming Ap's Priority 1, MaxLrads = 500, joined Aps =0
*spamApTask7: Jan 29 03:39:08.104: apModel:
*spamApTask7: Jan 29 03:39:08.104: apType = 38 apModel:
*spamApTask0: Jan 29 03:39:08.105: 4c:00:82:9a:47:a3 Received LWAPP DISCOVERY REQUEST to 6c:41:6a:5f:95:2f on port '13'
*spamApTask0: Jan 29 03:39:08.105: 4c:00:82:9a:47:a3 Discarding discovery request in LWAPP from AP supporting CAPWAP
*spamApTask7: Jan 29 03:39:08.105: 4c:00:82:9a:47:a0 Discovery Response sent to 10.2.3.100 port 42107
*spamApTask7: Jan 29 03:39:08.105: 4c:00:82:9a:47:a0 Discovery Response sent to 10.2.3.100:42107
*spamApTask7: Jan 29 03:39:08.105: 4c:00:82:9a:47:a0 Discovery Request from 10.2.3.100:42107
*spamApTask7: Jan 29 03:39:08.105: 4c:00:82:9a:47:a0 Join Priority Processing status = 0, Incoming Ap's Priority 1, MaxLrads = 500, joined Aps =0
*spamApTask7: Jan 29 03:39:08.105: apModel:
*spamApTask7: Jan 29 03:39:08.105: apType = 38 apModel:
*spamApTask7: Jan 29 03:39:08.105: 4c:00:82:9a:47:a0 Discovery Response sent to 10.2.3.100 port 42107
*spamApTask7: Jan 29 03:39:08.105: 4c:00:82:9a:47:a0 Discovery Response sent to 10.2.3.100:42107
*spamApTask7: Jan 29 03:39:08.105: 4c:00:82:9a:47:a0 Discovery Request from 10.2.3.100:42107
*spamApTask7: Jan 29 03:39:08.105: 4c:00:82:9a:47:a0 Join Priority Processing status = 0, Incoming Ap's Priority 1, MaxLrads = 500, joined Aps =0
*spamApTask7: Jan 29 03:39:08.105: apModel:
*spamApTask7: Jan 29 03:39:08.105: apType = 38 apModel:
*spamApTask7: Jan 29 03:39:08.106: 4c:00:82:9a:47:a0 Discovery Response sent to 10.2.3.100 port 42107
(Cisco Controller) >*spamApTask7: Jan 29 03:39:08.106: 4c:00:82:9a:47:a0 Discovery Response sent to 10.2.3.100:42107
*spamApTask7: Jan 29 03:39:18.104: 4c:00:82:9a:47:a3 DTLS connection not found, creating new connection for 10:2:3:100 (42107) 10:2:3:230 (5246)
*spamApTask7: Jan 29 03:39:18.638: acDtlsPlumbControlPlaneKeys: lrad:10.2.3.100(42107) mwar:10.2.3.230(5246)
*spamApTask7: Jan 29 03:39:18.638: 4c:00:82:9a:47:a3 Allocated index from main list, Index: 397
*spamApTask7: Jan 29 03:39:18.638: 4c:00:82:9a:47:a3 Using CipherSuite AES128-SHA
*spamApTask7: Jan 29 03:39:18.638: 4c:00:82:9a:47:a3 DTLS keys for Control Plane are plumbed successfully for AP 10.2.3.100. Index 398
*spamApTask6: Jan 29 03:39:18.638: 4c:00:82:9a:47:a3 DTLS Session established server (10.2.3.230:5246), client (10.2.3.100:42107)
*spamApTask6: Jan 29 03:39:18.638: 4c:00:82:9a:47:a3 Starting wait join timer for AP: 10.2.3.100:42107
*spamApTask7: Jan 29 03:39:23.636: 4c:00:82:9a:47:a0 Join Request from 10.2.3.100:42107
*spamApTask7: Jan 29 03:39:23.636: 4c:00:82:9a:47:a3 Deleting AP entry 10.2.3.100:42107 from temporary database.
*spamApTask7: Jan 29 03:39:23.637: 4c:00:82:9a:47:a0 MIC AP is not allowed to join by config
*spamApTask7: Jan 29 03:39:23.637: 4c:00:82:9a:47:a0 Join Request failed! -
Problem Joining AIR-CAP1602I-C-K9 with WLC 5508
Hi,
I am having trouble to get AIR CAP1602I-C-K9 attached to a 5508 WLC running code 7.4.110.0
Here is what I got from the AP logs:
====================================================================================================
Extracting files...
ap1g2-k9w8-mx.152-2.JB2/ (directory) 0 (bytes)
extracting ap1g2-k9w8-mx.152-2.JB2/K5.bin (75790 bytes)!!!!
*Dec 6 15:09:23.011: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*Dec 6 15:09:23.535: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 172.16.10.100 peer_port: 5246
*Dec 6 15:09:23.535: %CAPWAP-5-SENDJOIN: sending Join Request to 172.16.10.100
*Dec 6 15:09:23.535: %CAPWAP-3-ERRORLOG: Invalid event 10 & state 5 combination.
*Dec 6 15:09:23.535: %CAPWAP-3-ERRORLOG: CAPWAP!
extracting ap1g2-k9w8-mx.152-2.JB2/ap1g2-k9w8-mx.152-2.JB2 (9202946 bytes)!!!!!!!!! SM handler: Failed to process message type 10 state 5.
*Dec 6 15:09:23.535: %CAPWAP-3-ERRORLOG: Failed to handle capwap control message from controller
*Dec 6 15:09:23.535: %CAPWAP-3-ERRORLOG: Failed to process encrypted capwap packet from 172.16.10.100perform archive download capwap:/ap1g2 tar file
*Dec 6 15:09:23.583: %CAPWAP-6-AP_IMG_DWNLD: Required image not found on AP. Downloading image from Controller.
*Dec 6 15:09:23.587: Loading file /ap1g2...
*Dec 6 15:09:24.007: %LINEPROTO-5-UPDOWN:!!!!!!!!!!! Line protocol on Interface Dot11Radio0, changed state to down
*Dec 6 15:09:24.063: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to up!!!!!!!!!!!
*Dec 6 15:09:25.139: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to up!!!!!!!!!!
*Dec 6 15:09:26.135: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
Premature end of tar file
ERROR: Problem extracting files from archive.
Download image failed, notify controller!!! From:7.4.1.37 to 7.4.110.0, FailureCode:3
archive download: takes 63 seconds
*Dec 6 15:10:26.851: capwap_image_proc: problem extracting tar file
====================================================================================
after that the AP reboots and do same process over and over again,
Please help..
Many Thanks,
BarthHere is the info about AP and WLC:
(Cisco Controller) >show sysinfo
Manufacturer's Name.............................. Cisco Systems Inc.
Product Name..................................... Cisco Controller
Product Version.................................. 7.4.110.0
Bootloader Version............................... 1.0.1
Field Recovery Image Version..................... 6.0.182.0
Firmware Version................................. FPGA 1.7, Env 1.8, USB console 2.2
Build Type....................................... DATA + WPS
System Name...................................... WLC1-AP
System Location..................................
System Contact...................................
System ObjectID.................................. 1.3.6.1.4.1.9.1.1069
Redundancy Mode.................................. Disabled
IP Address....................................... 172.16.10.100
Last Reset....................................... Power on reset
System Up Time................................... 0 days 4 hrs 12 mins 28 secs
System Timezone Location.........................
System Stats Realtime Interval................... 5
System Stats Normal Interval..................... 180
Configured Country............................... US - United States
Operating Environment............................ Commercial (0 to 40 C)
--More-- or (q)uit
Internal Temp Alarm Limits....................... 0 to 65 C
Internal Temperature............................. +44 C
External Temperature............................. +28 C
Fan Status....................................... OK
State of 802.11b Network......................... Enabled
State of 802.11a Network......................... Enabled
Number of WLANs.................................. 1
Number of Active Clients......................... 0
Memory Current Usage............................. Unknown
Memory Average Usage............................. Unknown
CPU Current Usage................................ Unknown
CPU Average Usage................................ Unknown
Burned-in MAC Address............................ F8:72:EA:EF:2E:A0
Power Supply 1................................... Present, OK
Power Supply 2................................... Present, Power Off, Fan On
Maximum number of APs supported.................. 100
AP4403.a7fd.f040#sh ver
Cisco IOS Software, C1600 Software (AP1G2-K9W8-M), Version 15.2(2)JB, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2012 by Cisco Systems, Inc.
Compiled Tue 11-Dec-12 04:45 by prod_rel_team
ROM: Bootstrap program is C1600 boot loader
BOOTLDR: C1600 Boot Loader (AP1G2-BOOT-M) LoaderVersion 15.2(2)JAX, RELEASE SOFTWARE (fc1)
AP4403.a7fd.f040 uptime is 4 minutes
System returned to ROM by power-on
System image file is "flash:/ap1g2-k9w8-mx.152-2.JB/ap1g2-k9w8-mx.152-2.JB"
Last reload reason:
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
[email protected].
cisco AIR-CAP1602I-C-K9 (PowerPC) processor (revision B0) with 98294K/32768K bytes of memory.
Processor board ID FGL1711ZJNW
PowerPC CPU at 533Mhz, revision number 0x2151
Last reset from power-on
LWAPP image version 7.4.1.37
1 Gigabit Ethernet interface
2 802.11 Radios
32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: 44:03:A7:FD:F0:40
Part Number : 73-14671-04
PCA Assembly Number : 000-00000-00
PCA Revision Number :
PCB Serial Number : FOC16517DZ1
Top Assembly Part Number : 800-38552-01
Top Assembly Serial Number : FGL1711ZJNW
Top Revision Number : A0
Product/Model Number : AIR-CAP1602I-C-K9
Configuration register is 0xF
AP4403.a7fd.f040#sh inventory
NAME: "AP1600", DESCR: "Cisco Aironet 1600 Series (IEEE 802.11n) Access Point"
PID: AIR-CAP1602I-C-K9 , VID: V01, SN: FGL1711ZJNW
Maybe you are looking for
-
Issue in creation of group in oim database through sql query.
hi guys, i am trying to create a group in oim database through sql query: insert into ugp(ugp_key,ugp_name,ugp_create,ugp_update,ugp_createby,ugp_updateby,)values(786,'dbrole','09-jul-12','09-jul-12',1,1); it is inserting the group in ugp table but i
-
Hasselblad Thumbnails (*.fff) not displayed in CS4
Hasselblad thumbnails (*.fff) not displayed. Older file-versions created from *.3fr to *.fff by FlexColor are displayed. Newer versions created by Phocus are not displayed. In Apples finder they are all displayed well and you can zoom in to full scre
-
How can I get iTunes to open to Library instead of the iTunes Store. It does it on one of my computers, but I don't know how I did it.
-
When I make a photobook, I would like to use a geografical map twice. How can I copy a map.
-
Hi, my macbook pro screen cracked after 8 days. I bought a replacement screen brand new online. I have 2 questions, first my machine is the 2.2ghz macbook pro that was 1999.99 list price. Is the screen I purchased the correct one? its model number M9