WLC 5508 Guest termination Tunnel
Hi to all,
I've a question regarding Guest Wireless Access: can the WLC5508 do Guest Termination Tunnel as they do the WLC440X??? I suppose yes...or better say I hope yes ;-)
What about the AP support? Can I mix as is possible with the 440X where the internal WLC are licensed for 50 AP and the external one for only 12???
Thanks for a feedback!
It sounds like you're running into the same project as me. I have all 4402's and was considering upgrading to a 5508 for our headquarters. This happens to be our guest anchor as well. To ensure that mobility will work, which is a requirement for guest, carefully read the version 6 release notes. In a nutshell though, I've found that this will work with 4.2 code and up to version 6 on a 5508. I'd check the release notes to be exactly sure of the 4.2 release though. 4.2.205.0 has been working well for me. I don't have our 5508 yet, but I'll provide an update once it gets here. In a perfect world, having the same version 6 release on the 4402's and the 5508 will ensure you don't have anchor / mobility problems.
As far as the different AP licenses go on the controllers, this will only affect the size of the network you can have at each site (because it restricts the number of AP's, ie. 25 versus 12). You can definitely use guest on a 50 AP controller with a 12AP controller at the other site. They don't have to match...
Similar Messages
-
Wlc 5508 : guest users to be configured only give access for internal SAP application
Hi,
I have one new requirement with one of the client.
I have wlc 5508 with 6.0 firmware. I need to have one guest wlan which will have access only for internal SAP application.
I have gone through cisco document for internet guest users , where web page will be redirected with user name and password once it is authenticated , we can access internet.
Provided if we have access list configured in wlc ... for internet access only /
what about this mentioned scenario ?
can anybody suggest on the same ?Hi Vinod,
Go for the ACL on any Router or the switch.. i prefer not on the WLC..
http://www.cisco.com/en/US/products/sw/secursw/ps1018/products_tech_note09186a00800a5b9a.shtml
Here is the link as well to do it on the WLC
http://www.cisco.com/en/US/tech/tk722/tk809/technologies_configuration_example09186a00807810d1.shtml
Lemme know if this answered ur question..
Regards
Surendra -
Cisco WLC 5508 Guest Authentification issue
Hi ..
I have one interface setup to a Cisco 2921 router connected to a Cable modem.
DHCP is on the 2921.
when I connect to the ssid for my guest i'm redirected to the authentification portal 1.1.1.1 .
I'm putting valide credential and when pressing the submit button .. it just go anywhere.
I have setup another SSID with a psk and it's working fine.. getting ip and able to browse internet.
From what i have read... it's apparently DNS issue on my router.. but what should I check.My client has ip like that
Description . . . . . . . . . . . : Intel(R) 82579LM Gigabit Network Connection
Physical Address. . . . . . . . . : 40-2C-F4-ED-AD-FB
IPv4 Address. . . . . . . . . . . : 192.168.6.36
Subnet Mask . . . . . . . . . . . : 255.255.255.0
Default Gateway . . . . . . . . . : 192.168.6.1
DNS Servers . . . . . . . . . . . : 24.200.241.37
24.200.243.189
DNS are the one from my service provider -
Where do you turn this option off? i have looked under security and did not see any thing. Thanks
Wlans -> Security -> Layer 3. ?
Sent from Cisco Technical Support iPad App -
Guest enrollment (self-service) on WLC 5508
Hi folks,
My desired setup is to integrate wlc 5508 (guest anchor) into cisco ise or nac server for guest authentication.
And then, ise or nac will connect to an SMS gateway to deliver credentials to mobile phones.
But I am looking into something unique where guests that enter into our facility can do self-enrollment. (i.e. guest connects to ssid and redirected to web authentication that asks for user information like name, email, mobile, etc).
After this process, guest will receive an sms for the credentials.
Does anyone here know a reliable third party software for the said enrolment that will work fine with my setup.
Your response are highly appreciated.Hi Saurav,
Now it is supported on 1.3
http://www.cisco.com/c/en/us/td/docs/security/ise/1-3/upgrade_guide/b_ise_upgrade_guide_13/b_ise_upgrade_guide_13_chapter_0101.html -
Hi,
I have a WLC 5508 connected in a hub and spoke topology. The WLC is located at the hub which is the main office. In one of the remote spoke locations I have five Access Points that are connected to the local LAN and the model for the APs is AIR-CAP3602I-E-K9. The APs are all connected to access ports on the switch in vlan 1. I have two WLAN configured on the controller. I have two interfaces configured on the controller. The management and the guest interface. WLAN 1 is associated with the management interface. In the WLAN 1 advanced setting the flex local switching option is enabled. WLAN 2 is associated with the guest interface and this interface is tunneling vlan 248 the guest vlan. The problem I am having is that the devices can not communicate with each other if they are connected to the wireless connection WLAN 2 which is the tunneled vlan.
Example: The client would like to be able to connect his ipad to the apple tv for presentation. If I connect both devices to the WLAN 1 which is using flex local switching option they can communicate with no problem, but if the devices are connected to WLAN 2 the guest vlan they can't communicate with each other. Is it possible to get this to also work on WLAN 2 ?
Note: Both WLAN types are WLAN and P2P Blocking Action is set to default (disabled).
Does any one have any ideas what could be causing my issue?
Thanks in advance for your help,Well since your talking about Apple TV, you need to look at this reference guide for Apple's bonjour. This will explain how to get it to work and the limitation when an AP is in local or FlexConnect mode. The bonjour just doesn't work as people think it should because they can get it to work with a linksys AP.
http://www.cisco.com/en/US/products/hw/wireless/ps4570/products_tech_note09186a0080bb1d7c.shtml
Sent from Cisco Technical Support iPhone App -
Cisco WLC 5508 with 3702APs - mobile hotspot for 2000 Guest users
Cisco WLC 5508 with 3702APs - mobile hotspot for 2000 Guest users
I've been given a fantastic "opportunity" by my boss to use our existing wireless infrastructure to provide internet access to potentially upto 2000 VIP guests arriving with BYOD devices, in a very densely populated area for a 3 day event. We are talking an area of approx 200m x 15m. Think of it as an awards ceremony/concert. The solution will also be mobile so we will be using internet breakout from different telcos as it will move to approx 20 countries. The area is also incredibly densely populated with other wifi APs. I did a brief site survey and AirMagnet could detect over 2500 other 'rogue' APs from where I was stood! I hope CleanAir works!
We need a simple authentication method for them to connect with zero admin from our side. We don't want to just offer up a rolling daily PSK as that's a bit amateur and we don't really want the VIP guests sharing the PSK with others during their stay. Ideally they could self-provision by providing an email address.
I know the WLC can handle webauth for local users but I don't think it scales very well. ie I don't think I can offer the account to several hundred people.
Cisco ISE looks a very expansive (and expensive) product but I don't think we need all it's capabilities (do I?). It would be nice to just ask a potential user for their email address and grant them access and email them next year. I've seen Cisco NAC but that looks over the top too for just guest users who will only be accessing a shared internet connection.
I've seen 3rd party supposed software solutions from Kiosk Antamedia etc do they work with Cisco Enterprise WLC solutions?
We'd like to limit users to a certain (low) bandwidth and block (say) torrent traffic to keep the general user experience worthwhile.
Does anybody have any case study documents or experience of such a project? As well as the authentication it's how well the APs will handle the dense potential number of clients trying to connect in such a confined space.
Any suggestions would be gratefully appreciated from the knowledgeable community.
Cheers,
MikeHi Rasika,
We are having WLC 5508 model with software version running 7.4.121.0. AP Models are AIR-CAP2602I.
Normally our WAN links are good even while the issue pertains. We are connected to remote offices over ipsec site to site vpn for WAN. The link latency in WLC between the AP and the controller shows <1ms.
currently the Guest network is using WPA2-PSK auth given in the controller. we are trying to find a option to make the Guest wireless auth local to the office, and see if this solves the problem.
any suggestions,
Thank you,
Arjun -
Prime Infrastructure 2.0 can not create the guest account on WLC 5508
The PI can manage the WLC which means the connection between them is ok, but I am not able to create the guest account on it. The WLC has guest SSID with web auth configured correctly..
Any idea why?
Thanks!raymond,
that's good to know that it required :
1) not only a RW community string
2) but also as well ssh credentials
i too would have thought option 1) would be all that was required but it doesn't appear that way w/ your response.
the only way i'll go to add devices in is by doing both SNMP RW and ssh at the same time.
now we know
thanks for pointing this out -
WLC 5508 integration with fortigate and Guest Vlan
Hi
I have 5508 Cisco WLC and i want to connect my wlc one port to fortigate (FW) for direct internet.
And other port in WLC i will connect on Cisco Core Switch for other SSID's and for management. Now the question is how to divide port in WLC 5508, how to point layer 3 traffic if don't configure switch port as trunk.
Kindly what will be best solution.sh etherchannel 99 sum
Flags: D - down P - bundled in port-channel
I - stand-alone s - suspended
H - Hot-standby (LACP only)
R - Layer3 S - Layer2
U - in use N - not in use, no aggregation
f - failed to allocate aggregator
M - not in use, no aggregation due to minimum links not met
m - not in use, port not aggregated due to minimum links not met
u - unsuitable for bundling
d - default port
w - waiting to be aggregated
Number of channel-groups in use: 38
Number of aggregators: 38
Group Port-channel Protocol Ports
------+-------------+-----------+-----------------------------------------------
99 Po99(SU) - Gi2/2/1(P) Gi2/2/2(P) Gi2/2/3(D)
Gi2/2/4(P)
Last applied Hash Distribution Algorithm: Fixed
Gi2/2/3 is down becasue we had to shut down the interface because when it is up many APs refuse to register. -
Cisco ISE 1.2 & Cisco WLC 5508 v7.6
Hi all,
we are planning to upgrade our WLC to 7.6 to fix a bug with FlexConnect Client ACLs but I have just seen on the Cisco ISE Compatibility table that the it only recommends up to v7.5 of the WLC 5508...
Cisco have told me to steer clear of 7.5 as it is in a defferred status, so does anyone know, or have running in a lab or production, ISE1.2 with a 5508 WLC v7.6 NAD ?
I would much rather know of any issues people are experiencing before hand than to have to go through a software upgrade and then rollback.
Thanks all
Mario De RosaHi Neno,
right I have this almost working now.
I have simplified the setup. I am not going to do any client provisioning at the moment.
So I can connect to the corporate SSID using EAP-TLS and I can successfully push the branch data VLAN upon successful authorisation.
Now I am trying to introduce the posture element & per user ACLs.
I have defined the redirect ACL & Flex ACL on the vWLC however the NAC agent will not pop-up. The client is in the right VLAN and the redirect ACL seems to be getting applied as the client does get an IP through DHCP. However, the client cannot ping the ISE or access the guest portal when I open the browser.
DNS resolution seems to be working fine.
VLAN220 is my datacentre VLAN which the Management Interface on the controller is plugged in to.
VLAN10 is the branch DATA VLAN.
below is some output to give you some more details...
(Cisco Controller) >show client detail 00:24:d6:97:b3:be
Client MAC Address............................... 00:24:d6:97:b3:be
Client Username ................................. [email protected]
AP MAC Address................................... 18:33:9d:f0:21:80
AP Name.......................................... test-flex-ap
AP radio slot Id................................. 0
Client State..................................... Associated
Client NAC OOB State............................. Access
Wireless LAN Id.................................. 2
Hotspot (802.11u)................................ Not Supported
BSSID............................................ 18:33:9d:f0:21:81
Connected For ................................... 128 secs
Channel.......................................... 6
IP Address....................................... 10.130.130.120
Gateway Address.................................. 10.130.130.1
Netmask.......................................... 255.255.255.0
IPv6 Address..................................... fe80::f524:1910:69f0:9482
Association Id................................... 1
Authentication Algorithm......................... Open System
Reason Code...................................... 1
Status Code...................................... 0
Client CCX version............................... 4
Client E2E version............................... 1
--More-- or (q)uit
Re-Authentication Timeout........................ 1651
QoS Level........................................ Silver
Avg data Rate.................................... 0
Burst data Rate.................................. 0
Avg Real time data Rate.......................... 0
Burst Real Time data Rate........................ 0
802.1P Priority Tag.............................. disabled
CTS Security Group Tag........................... Not Applicable
KTS CAC Capability............................... No
WMM Support...................................... Enabled
APSD ACs....................................... BK BE VI VO
Power Save....................................... OFF
Current Rate..................................... m13
Supported Rates.................................. 1.0,2.0,5.5,11.0,6.0,9.0,
............................................. 12.0,18.0,24.0,36.0,48.0,
............................................. 54.0
Mobility State................................... Local
Mobility Move Count.............................. 0
Security Policy Completed........................ No
Policy Manager State............................. POSTURE_REQD
Policy Manager Rule Created...................... Yes
AAA Override ACL Name............................ POSTURE_REDIRECT_ACL
AAA Override ACL Applied Status.................. Yes
--More-- or (q)uit
AAA Override Flex ACL Name....................... POSTURE_REDIRECT_ACL
AAA Override Flex ACL Applied Status............. Yes
AAA URL redirect................................. https://pdc-ise-man01.kier.group:8443/guestportal/gateway?sessionId=c8dc800a00000005b3e7e953&action=cpp
Audit Session ID................................. c8dc800a00000005b3e7e953
AAA Role Type.................................... none
Local Policy Applied............................. none
IPv4 ACL Name.................................... none
FlexConnect ACL Applied Status................... Yes
IPv4 ACL Applied Status.......................... Unavailable
IPv6 ACL Name.................................... none
IPv6 ACL Applied Status.......................... Unavailable
Layer2 ACL Name.................................. none
Layer2 ACL Applied Status........................ Unavailable
mDNS Status...................................... Disabled
mDNS Profile Name................................ none
No. of mDNS Services Advertised.................. 0
Policy Type...................................... WPA2
Authentication Key Management.................... 802.1x
Encryption Cipher................................ CCMP (AES)
Protected Management Frame ...................... No
Management Frame Protection...................... No
EAP Type......................................... EAP-TLS
FlexConnect Data Switching....................... Local
--More-- or (q)uit
FlexConnect Dhcp Status.......................... Local
FlexConnect Vlan Based Central Switching......... No
FlexConnect Authentication....................... Central
Quarantine VLAN.................................. 0
Access VLAN...................................... 220
Client Capabilities:
CF Pollable................................ Not implemented
CF Poll Request............................ Not implemented
Short Preamble............................. Implemented
PBCC....................................... Not implemented
Channel Agility............................ Not implemented
Listen Interval............................ 10
Fast BSS Transition........................ Not implemented
Client Wifi Direct Capabilities:
WFD capable................................ No
Manged WFD capable......................... No
Cross Connection Capable................... No
Support Concurrent Operation............... No
Fast BSS Transition Details:
Client Statistics:
Number of Bytes Received................... 33698
Number of Bytes Sent....................... 19397
Total Number of Bytes Sent................. 19397
--More-- or (q)uit
Total Number of Bytes Recv................. 33698
Number of Bytes Sent (last 90s)............ 19397
Number of Bytes Recv (last 90s)............ 33698
Number of Packets Received................. 283
Number of Packets Sent..................... 147
Number of Interim-Update Sent.............. 0
Number of EAP Id Request Msg Timeouts...... 0
Number of EAP Id Request Msg Failures...... 0
Number of EAP Request Msg Timeouts......... 0
Number of EAP Request Msg Failures......... 0
Number of EAP Key Msg Timeouts............. 0
Number of EAP Key Msg Failures............. 0
Number of Data Retries..................... 53
Number of RTS Retries...................... 0
Number of Duplicate Received Packets....... 2
Number of Decrypt Failed Packets........... 0
Number of Mic Failured Packets............. 0
Number of Mic Missing Packets.............. 0
Number of RA Packets Dropped............... 0
Number of Policy Errors.................... 0
Radio Signal Strength Indicator............ -42 dBm
Signal to Noise Ratio...................... 41 dB
Client Rate Limiting Statistics:
--More-- or (q)uit
Number of Data Packets Recieved............ 0
Number of Data Rx Packets Dropped.......... 0
Number of Data Bytes Recieved.............. 0
Number of Data Rx Bytes Dropped............ 0
Number of Realtime Packets Recieved........ 0
Number of Realtime Rx Packets Dropped...... 0
Number of Realtime Bytes Recieved.......... 0
Number of Realtime Rx Bytes Dropped........ 0
Number of Data Packets Sent................ 0
Number of Data Tx Packets Dropped.......... 0
Number of Data Bytes Sent.................. 0
Number of Data Tx Bytes Dropped............ 0
Number of Realtime Packets Sent............ 0
Number of Realtime Tx Packets Dropped...... 0
Number of Realtime Bytes Sent.............. 0
Number of Realtime Tx Bytes Dropped........ 0
Nearby AP Statistics:
test-flex-ap(slot 0)
antenna0: 14 secs ago.................... -51 dBm
antenna1: 14 secs ago.................... -37 dBm
test-flex-ap(slot 1)
antenna0: 14 secs ago.................... -51 dBm
antenna1: 14 secs ago.................... -54 dBm
--More-- or (q)uit
DNS Server details:
DNS server IP ............................. 10.0.17.31
DNS server IP ............................. 10.0.17.43
Assisted Roaming Prediction List details:
Client Dhcp Required: False
Allowed (URL)IP Addresses
(Cisco Controller) >
(Cisco Controller) >show wlan 2
WLAN Identifier.................................. 2
Profile Name..................................... Demo1x
Network Name (SSID).............................. Demo1x
Status........................................... Enabled
MAC Filtering.................................... Disabled
Broadcast SSID................................... Enabled
AAA Policy Override.............................. Enabled
Network Admission Control
Client Profiling Status
Radius Profiling ............................ Disabled
DHCP ....................................... Disabled
HTTP ....................................... Disabled
Local Profiling ............................. Disabled
DHCP ....................................... Disabled
HTTP ....................................... Disabled
Radius-NAC State............................... Enabled
SNMP-NAC State................................. Disabled
Quarantine VLAN................................ 0
Maximum number of Associated Clients............. 0
Maximum number of Clients per AP Radio........... 200
--More-- or (q)uit
Number of Active Clients......................... 1
Exclusionlist Timeout............................ 60 seconds
Session Timeout.................................. 1800 seconds
User Idle Timeout................................ Disabled
Sleep Client..................................... disable
Sleep Client Timeout............................. 12 hours
User Idle Threshold.............................. 0 Bytes
NAS-identifier................................... mario-test-flex-vwlc
CHD per WLAN..................................... Enabled
Webauth DHCP exclusion........................... Disabled
Interface........................................ management
Multicast Interface.............................. Not Configured
WLAN IPv4 ACL.................................... unconfigured
WLAN IPv6 ACL.................................... unconfigured
WLAN Layer2 ACL.................................. unconfigured
mDNS Status...................................... Disabled
mDNS Profile Name................................ unconfigured
DHCP Server...................................... Default
DHCP Address Assignment Required................. Disabled
Static IP client tunneling....................... Disabled
Quality of Service............................... Silver
Per-SSID Rate Limits............................. Upstream Downstream
Average Data Rate................................ 0 0
--More-- or (q)uit
Average Realtime Data Rate....................... 0 0
Burst Data Rate.................................. 0 0
Burst Realtime Data Rate......................... 0 0
Per-Client Rate Limits........................... Upstream Downstream
Average Data Rate................................ 0 0
Average Realtime Data Rate....................... 0 0
Burst Data Rate.................................. 0 0
Burst Realtime Data Rate......................... 0 0
Scan Defer Priority.............................. 4,5,6
Scan Defer Time.................................. 100 milliseconds
WMM.............................................. Allowed
WMM UAPSD Compliant Client Support............... Disabled
Media Stream Multicast-direct.................... Disabled
CCX - AironetIe Support.......................... Enabled
CCX - Gratuitous ProbeResponse (GPR)............. Disabled
CCX - Diagnostics Channel Capability............. Disabled
Dot11-Phone Mode (7920).......................... Disabled
Wired Protocol................................... None
Passive Client Feature........................... Disabled
Peer-to-Peer Blocking Action..................... Disabled
Radio Policy..................................... All
DTIM period for 802.11a radio.................... 1
DTIM period for 802.11b radio.................... 1
--More-- or (q)uit
Radius Servers
Authentication................................ 10.0.16.111 1812
Accounting.................................... 10.131.16.111 1813
Interim Update............................. Disabled
Framed IPv6 Acct AVP ...................... Prefix
Dynamic Interface............................. Disabled
Dynamic Interface Priority.................... wlan
Local EAP Authentication......................... Disabled
Security
802.11 Authentication:........................ Open System
FT Support.................................... Disabled
Static WEP Keys............................... Disabled
802.1X........................................ Disabled
Wi-Fi Protected Access (WPA/WPA2)............. Enabled
WPA (SSN IE)............................... Disabled
WPA2 (RSN IE).............................. Enabled
TKIP Cipher............................. Disabled
AES Cipher.............................. Enabled
Auth Key Management
802.1x.................................. Enabled
PSK..................................... Disabled
CCKM.................................... Disabled
--More-- or (q)uit
FT-1X(802.11r).......................... Disabled
FT-PSK(802.11r)......................... Disabled
PMF-1X(802.11w)......................... Disabled
PMF-PSK(802.11w)........................ Disabled
FT Reassociation Timeout................... 20
FT Over-The-DS mode........................ Enabled
GTK Randomization.......................... Disabled
SKC Cache Support.......................... Disabled
CCKM TSF Tolerance......................... 1000
WAPI.......................................... Disabled
Wi-Fi Direct policy configured................ Disabled
EAP-Passthrough............................... Disabled
CKIP ......................................... Disabled
Web Based Authentication...................... Disabled
Web-Passthrough............................... Disabled
Conditional Web Redirect...................... Disabled
Splash-Page Web Redirect...................... Disabled
Auto Anchor................................... Disabled
FlexConnect Local Switching................... Enabled
flexconnect Central Dhcp Flag................. Disabled
flexconnect nat-pat Flag...................... Disabled
flexconnect Dns Override Flag................. Disabled
flexconnect PPPoE pass-through................ Disabled
--More-- or (q)uit
flexconnect local-switching IP-source-guar.... Disabled
FlexConnect Vlan based Central Switching ..... Disabled
FlexConnect Local Authentication.............. Disabled
FlexConnect Learn IP Address.................. Enabled
Client MFP.................................... Optional
PMF........................................... Disabled
PMF Association Comeback Time................. 1
PMF SA Query RetryTimeout..................... 200
Tkip MIC Countermeasure Hold-down Timer....... 60
Eap-params.................................... Disabled
AVC Visibilty.................................... Disabled
AVC Profile Name................................. None
Flow Monitor Name................................ None
Split Tunnel (Printers).......................... Disabled
Call Snooping.................................... Disabled
Roamed Call Re-Anchor Policy..................... Disabled
SIP CAC Fail Send-486-Busy Policy................ Disabled
SIP CAC Fail Send Dis-Association Policy......... Disabled
KTS based CAC Policy............................. Disabled
Assisted Roaming Prediction Optimization......... Disabled
802.11k Neighbor List............................ Disabled
802.11k Neighbor List Dual Band.................. Disabled
Band Select...................................... Disabled
--More-- or (q)uit
Load Balancing................................... Disabled
Multicast Buffer................................. Disabled
Mobility Anchor List
WLAN ID IP Address Status
802.11u........................................ Disabled
MSAP Services.................................. Disabled
Local Policy
Priority Policy Name
(Cisco Controller) >
when debugging the client during redirect, this is the output and I cannot spot anything wrong here...
(Cisco Controller) >*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Adding mobile on LWAPP AP 18:33:9d:f0:21:80(1)
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Association received from mobile on BSSID 18:33:9d:f0:21:8e
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Global 200 Clients are allowed to AP radio
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Max Client Trap Threshold: 0 cur: 0
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Rf profile 600 Clients are allowed to AP wlan
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be override for default ap group, marking intgrp NULL
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Applying Interface policy on Mobile, role Unassociated. Ms NAC State 0 Quarantine Vlan 0 Access Vlan 0
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Re-applying interface policy for client
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be 0.0.0.0 START (0) Changing IPv4 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2219)
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be 0.0.0.0 START (0) Changing IPv6 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2240)
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be apfApplyWlanPolicy: Retaining the ACL recieved in AAA attributes 255 on mobile
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be apfApplyWlanPolicy: Apply WLAN Policy over PMIPv6 Client Mobility Type
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be In processSsidIE:4850 setting Central switched to FALSE
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Applying site-specific Local Bridging override for station 00:24:d6:97:b3:be - vapId 2, site 'default-group', interface 'management'
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Applying Local Bridging Interface Policy for station 00:24:d6:97:b3:be - vlan 220, interface id 0, interface 'management'
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be processSsidIE statusCode is 0 and status is 0
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be processSsidIE ssid_done_flag is 0 finish_flag is 0
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be STA - rates (8): 140 18 152 36 176 72 96 108 0 0 0 0 0 0 0 0
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be suppRates statusCode is 0 and gotSuppRatesElement is 1
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Processing RSN IE type 48, length 22 for mobile 00:24:d6:97:b3:be
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Received RSN IE with 0 PMKIDs from mobile 00:24:d6:97:b3:be
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Setting active key cache index 8 ---> 8
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be unsetting PmkIdValidatedByAp
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Updating AID for REAP AP Client 18:33:9d:f0:21:80 - AID ===> 1
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be 0.0.0.0 START (0) Initializing policy
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be 0.0.0.0 START (0) Change state to AUTHCHECK (2) last state START (0)
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be 0.0.0.0 AUTHCHECK (2) Change state to 8021X_REQD (3) last state AUTHCHECK (2)
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Central switch is FALSE
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be 0.0.0.0 8021X_REQD (3) DHCP required on AP 18:33:9d:f0:21:80 vapId 2 apVapId 2for this client
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Not Using WMM Compliance code qosCap 00
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be 0.0.0.0 8021X_REQD (3) Plumbed mobile LWAPP rule on AP 18:33:9d:f0:21:80 vapId 2 apVapId 2 flex-acl-name:
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be apfMsAssoStateInc
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be apfPemAddUser2 (apf_policy.c:333) Changing state for mobile 00:24:d6:97:b3:be on AP 18:33:9d:f0:21:80 from Idle to Associated
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be apfPemAddUser2:session timeout forstation 00:24:d6:97:b3:be - Session Tout 0, apfMsTimeOut '0' and sessionTimerRunning flag is 0
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Stopping deletion of Mobile Station: (callerId: 48)
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Func: apfPemAddUser2, Ms Timeout = 0, Session Timeout = 0
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Sending Assoc Response to station on BSSID 18:33:9d:f0:21:8e (status 0) ApVapId 2 Slot 1
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be apfProcessAssocReq (apf_80211.c:8294) Changing state for mobile 00:24:d6:97:b3:be on AP 18:33:9d:f0:21:80 from Associated to Associated
*spamApTask6: Aug 12 10:58:24.016: 00:24:d6:97:b3:be Sent 1x initiate message to multi thread task for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.016: 00:24:d6:97:b3:be EAP-PARAM Debug - eap-params for Wlan-Id :2 is disabled - applying Global eap timers and retries
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.016: 00:24:d6:97:b3:be Station 00:24:d6:97:b3:be setting dot1x reauth timeout = 1800
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.016: 00:24:d6:97:b3:be dot1x - moving mobile 00:24:d6:97:b3:be into Connecting state
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.016: 00:24:d6:97:b3:be Sending EAP-Request/Identity to mobile 00:24:d6:97:b3:be (EAP Id 1)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.016: 00:24:d6:97:b3:be mscb->apfMsLwappLradNhMac = 00:00:0c:07:ac:dc mscb->apfMsLradSlotId = 1 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.016: 00:24:d6:97:b3:be mscb->apfMsBssid = 18:33:9d:f0:21:80 mscb->apfMsAddress = 00:24:d6:97:b3:be mscb->apfMsApVapId = 2
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.016: 00:24:d6:97:b3:be dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 220 mscb->apfMsLwappMwarInet.ipv4.addr = 176217288
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.016: 00:24:d6:97:b3:be mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = 176325157 mscb->apfMsLwappLradPort = 9385
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.083: 00:24:d6:97:b3:be Received EAPOL EAPPKT from mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.083: 00:24:d6:97:b3:be Received Identity Response (count=1) from mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.083: 00:24:d6:97:b3:be Resetting reauth count 1 to 0 for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.083: 00:24:d6:97:b3:be EAP State update from Connecting to Authenticating for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.083: 00:24:d6:97:b3:be dot1x - moving mobile 00:24:d6:97:b3:be into Authenticating state
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.083: 00:24:d6:97:b3:be Entering Backend Auth Response state for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.086: 00:24:d6:97:b3:be Processing Access-Challenge for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.086: 00:24:d6:97:b3:be Entering Backend Auth Req state (id=214) for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.086: 00:24:d6:97:b3:be WARNING: updated EAP-Identifier 1 ===> 214 for STA 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.086: 00:24:d6:97:b3:be Sending EAP Request from AAA to mobile 00:24:d6:97:b3:be (EAP Id 214)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.086: 00:24:d6:97:b3:be Allocating EAP Pkt for retransmission to mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.086: 00:24:d6:97:b3:be mscb->apfMsLwappLradNhMac = 00:00:0c:07:ac:dc mscb->apfMsLradSlotId = 1 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.086: 00:24:d6:97:b3:be mscb->apfMsBssid = 18:33:9d:f0:21:80 mscb->apfMsAddress = 00:24:d6:97:b3:be mscb->apfMsApVapId = 2
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.086: 00:24:d6:97:b3:be dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 220 mscb->apfMsLwappMwarInet.ipv4.addr = 176217288
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.086: 00:24:d6:97:b3:be mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = 176325157 mscb->apfMsLwappLradPort = 9385
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.090: 00:24:d6:97:b3:be Received EAPOL EAPPKT from mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.090: 00:24:d6:97:b3:be Received EAP Response from mobile 00:24:d6:97:b3:be (EAP Id 214, EAP Type 13)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.090: 00:24:d6:97:b3:be Resetting reauth count 0 to 0 for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.090: 00:24:d6:97:b3:be Entering Backend Auth Response state for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.091: 00:24:d6:97:b3:be Processing Access-Challenge for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.091: 00:24:d6:97:b3:be Entering Backend Auth Req state (id=215) for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.091: 00:24:d6:97:b3:be Sending EAP Request from AAA to mobile 00:24:d6:97:b3:be (EAP Id 215)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.091: 00:24:d6:97:b3:be Reusing allocated memory for EAP Pkt for retransmission to mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.091: 00:24:d6:97:b3:be mscb->apfMsLwappLradNhMac = 00:00:0c:07:ac:dc mscb->apfMsLradSlotId = 1 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.091: 00:24:d6:97:b3:be mscb->apfMsBssid = 18:33:9d:f0:21:80 mscb->apfMsAddress = 00:24:d6:97:b3:be mscb->apfMsApVapId = 2
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.091: 00:24:d6:97:b3:be dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 220 mscb->apfMsLwappMwarInet.ipv4.addr = 176217288
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.091: 00:24:d6:97:b3:be mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = 176325157 mscb->apfMsLwappLradPort = 9385
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.095: 00:24:d6:97:b3:be Received EAPOL EAPPKT from mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.095: 00:24:d6:97:b3:be Received EAP Response from mobile 00:24:d6:97:b3:be (EAP Id 215, EAP Type 13)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.095: 00:24:d6:97:b3:be Resetting reauth count 0 to 0 for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.095: 00:24:d6:97:b3:be Entering Backend Auth Response state for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.096: 00:24:d6:97:b3:be Processing Access-Challenge for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.096: 00:24:d6:97:b3:be Entering Backend Auth Req state (id=216) for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.096: 00:24:d6:97:b3:be Sending EAP Request from AAA to mobile 00:24:d6:97:b3:be (EAP Id 216)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.096: 00:24:d6:97:b3:be Reusing allocated memory for EAP Pkt for retransmission to mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.096: 00:24:d6:97:b3:be mscb->apfMsLwappLradNhMac = 00:00:0c:07:ac:dc mscb->apfMsLradSlotId = 1 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.096: 00:24:d6:97:b3:be mscb->apfMsBssid = 18:33:9d:f0:21:80 mscb->apfMsAddress = 00:24:d6:97:b3:be mscb->apfMsApVapId = 2
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.096: 00:24:d6:97:b3:be dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 220 mscb->apfMsLwappMwarInet.ipv4.addr = 176217288
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.096: 00:24:d6:97:b3:be mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = 176325157 mscb->apfMsLwappLradPort = 9385
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.100: 00:24:d6:97:b3:be Received EAPOL EAPPKT from mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.100: 00:24:d6:97:b3:be Received EAP Response from mobile 00:24:d6:97:b3:be (EAP Id 216, EAP Type 13)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.100: 00:24:d6:97:b3:be Resetting reauth count 0 to 0 for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.100: 00:24:d6:97:b3:be Entering Backend Auth Response state for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.101: 00:24:d6:97:b3:be Processing Access-Challenge for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.101: 00:24:d6:97:b3:be Entering Backend Auth Req state (id=217) for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.101: 00:24:d6:97:b3:be Sending EAP Request from AAA to mobile 00:24:d6:97:b3:be (EAP Id 217)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.101: 00:24:d6:97:b3:be Reusing allocated memory for EAP Pkt for retransmission to mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.101: 00:24:d6:97:b3:be mscb->apfMsLwappLradNhMac = 00:00:0c:07:ac:dc mscb->apfMsLradSlotId = 1 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.101: 00:24:d6:97:b3:be mscb->apfMsBssid = 18:33:9d:f0:21:80 mscb->apfMsAddress = 00:24:d6:97:b3:be mscb->apfMsApVapId = 2
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.101: 00:24:d6:97:b3:be dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 220 mscb->apfMsLwappMwarInet.ipv4.addr = 176217288
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.101: 00:24:d6:97:b3:be mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = 176325157 mscb->apfMsLwappLradPort = 9385
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.105: 00:24:d6:97:b3:be Received EAPOL EAPPKT from mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.105: 00:24:d6:97:b3:be Received EAP Response from mobile 00:24:d6:97:b3:be (EAP Id 217, EAP Type 13)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.105: 00:24:d6:97:b3:be Resetting reauth count 0 to 0 for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.105: 00:24:d6:97:b3:be Entering Backend Auth Response state for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.106: 00:24:d6:97:b3:be Processing Access-Challenge for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.106: 00:24:d6:97:b3:be Entering Backend Auth Req state (id=218) for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.106: 00:24:d6:97:b3:be Sending EAP Request from AAA to mobile 00:24:d6:97:b3:be (EAP Id 218)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.106: 00:24:d6:97:b3:be Reusing allocated memory for EAP Pkt for retransmission to mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.106: 00:24:d6:97:b3:be mscb->apfMsLwappLradNhMac = 00:00:0c:07:ac:dc mscb->apfMsLradSlotId = 1 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.106: 00:24:d6:97:b3:be mscb->apfMsBssid = 18:33:9d:f0:21:80 mscb->apfMsAddress = 00:24:d6:97:b3:be mscb->apfMsApVapId = 2
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.106: 00:24:d6:97:b3:be dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 220 mscb->apfMsLwappMwarInet.ipv4.addr = 176217288
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.106: 00:24:d6:97:b3:be mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = 176325157 mscb->apfMsLwappLradPort = 9385
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.110: 00:24:d6:97:b3:be Received EAPOL EAPPKT from mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.110: 00:24:d6:97:b3:be Received EAP Response from mobile 00:24:d6:97:b3:be (EAP Id 218, EAP Type 13)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.110: 00:24:d6:97:b3:be Resetting reauth count 0 to 0 for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.110: 00:24:d6:97:b3:be Entering Backend Auth Response state for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.111: 00:24:d6:97:b3:be Processing Access-Challenge for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.111: 00:24:d6:97:b3:be Entering Backend Auth Req state (id=219) for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.111: 00:24:d6:97:b3:be Sending EAP Request from AAA to mobile 00:24:d6:97:b3:be (EAP Id 219)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.111: 00:24:d6:97:b3:be Reusing allocated memory for EAP Pkt for retransmission to mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.111: 00:24:d6:97:b3:be mscb->apfMsLwappLradNhMac = 00:00:0c:07:ac:dc mscb->apfMsLradSlotId = 1 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.111: 00:24:d6:97:b3:be mscb->apfMsBssid = 18:33:9d:f0:21:80 mscb->apfMsAddress = 00:24:d6:97:b3:be mscb->apfMsApVapId = 2
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.111: 00:24:d6:97:b3:be dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 220 mscb->apfMsLwappMwarInet.ipv4.addr = 176217288
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.111: 00:24:d6:97:b3:be mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = 176325157 mscb->apfMsLwappLradPort = 9385
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.115: 00:24:d6:97:b3:be Received EAPOL EAPPKT from mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.115: 00:24:d6:97:b3:be Received EAP Response from mobile 00:24:d6:97:b3:be (EAP Id 219, EAP Type 13)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.115: 00:24:d6:97:b3:be Resetting reauth count 0 to 0 for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.115: 00:24:d6:97:b3:be Entering Backend Auth Response state for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.116: 00:24:d6:97:b3:be Processing Access-Challenge for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.116: 00:24:d6:97:b3:be Entering Backend Auth Req state (id=220) for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.116: 00:24:d6:97:b3:be Sending EAP Request from AAA to mobile 00:24:d6:97:b3:be (EAP Id 220)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.116: 00:24:d6:97:b3:be Reusing allocated memory for EAP Pkt for retransmission to mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.116: 00:24:d6:97:b3:be mscb->apfMsLwappLradNhMac = 00:00:0c:07:ac:dc mscb->apfMsLradSlotId = 1 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.116: 00:24:d6:97:b3:be mscb->apfMsBssid = 18:33:9d:f0:21:80 mscb->apfMsAddress = 00:24:d6:97:b3:be mscb->apfMsApVapId = 2
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.116: 00:24:d6:97:b3:be dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 220 mscb->apfMsLwappMwarInet.ipv4.addr = 176217288
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.116: 00:24:d6:97:b3:be mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = 176325157 mscb->apfMsLwappLradPort = 9385
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.352: 00:24:d6:97:b3:be Received EAPOL EAPPKT from mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.352: 00:24:d6:97:b3:be Received EAP Response from mobile 00:24:d6:97:b3:be (EAP Id 220, EAP Type 13)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.352: 00:24:d6:97:b3:be Resetting reauth count 0 to 0 for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.352: 00:24:d6:97:b3:be Entering Backend Auth Response state for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.354: 00:24:d6:97:b3:be Processing Access-Challenge for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.354: 00:24:d6:97:b3:be Entering Backend Auth Req state (id=221) for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.354: 00:24:d6:97:b3:be Sending EAP Request from AAA to mobile 00:24:d6:97:b3:be (EAP Id 221)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.354: 00:24:d6:97:b3:be Reusing allocated memory for EAP Pkt for retransmission to mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.354: 00:24:d6:97:b3:be mscb->apfMsLwappLradNhMac = 00:00:0c:07:ac:dc mscb->apfMsLradSlotId = 1 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.354: 00:24:d6:97:b3:be mscb->apfMsBssid = 18:33:9d:f0:21:80 mscb->apfMsAddress = 00:24:d6:97:b3:be mscb->apfMsApVapId = 2
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.354: 00:24:d6:97:b3:be dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 220 mscb->apfMsLwappMwarInet.ipv4.addr = 176217288
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.354: 00:24:d6:97:b3:be mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = 176325157 mscb->apfMsLwappLradPort = 9385
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.359: 00:24:d6:97:b3:be Received EAPOL EAPPKT from mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.359: 00:24:d6:97:b3:be Received EAP Response from mobile 00:24:d6:97:b3:be (EAP Id 221, EAP Type 13)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.359: 00:24:d6:97:b3:be Resetting reauth count 0 to 0 for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.359: 00:24:d6:97:b3:be Entering Backend Auth Response state for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.360: 00:24:d6:97:b3:be Processing Access-Challenge for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.360: 00:24:d6:97:b3:be Entering Backend Auth Req state (id=222) for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.360: 00:24:d6:97:b3:be Sending EAP Request from AAA to mobile 00:24:d6:97:b3:be (EAP Id 222)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.360: 00:24:d6:97:b3:be Reusing allocated memory for EAP Pkt for retransmission to mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.360: 00:24:d6:97:b3:be mscb->apfMsLwappLradNhMac = 00:00:0c:07:ac:dc mscb->apfMsLradSlotId = 1 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.360: 00:24:d6:97:b3:be mscb->apfMsBssid = 18:33:9d:f0:21:80 mscb->apfMsAddress = 00:24:d6:97:b3:be mscb->apfMsApVapId = 2
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.360: 00:24:d6:97:b3:be dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 220 mscb->apfMsLwappMwarInet.ipv4.addr = 176217288
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.360: 00:24:d6:97:b3:be mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = 176325157 mscb->apfMsLwappLradPort = 9385
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.365: 00:24:d6:97:b3:be Received EAPOL EAPPKT from mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.365: 00:24:d6:97:b3:be Received EAP Response from mobile 00:24:d6:97:b3:be (EAP Id 222, EAP Type 13)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.365: 00:24:d6:97:b3:be Resetting reauth count 0 to 0 for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.365: 00:24:d6:97:b3:be Entering Backend Auth Response state for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.366: 00:24:d6:97:b3:be Processing Access-Challenge for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.366: 00:24:d6:97:b3:be Entering Backend Auth Req state (id=223) for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.366: 00:24:d6:97:b3:be Sending EAP Request from AAA to mobile 00:24:d6:97:b3:be (EAP Id 223)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.366: 00:24:d6:97:b3:be Reusing allocated memory for EAP Pkt for retransmission to mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.366: 00:24:d6:97:b3:be mscb->apfMsLwappLradNhMac = 00:00:0c:07:ac:dc mscb->apfMsLradSlotId = 1 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.366: 00:24:d6:97:b3:be mscb->apfMsBssid = 18:33:9d:f0:21:80 mscb->apfMsAddress = 00:24:d6:97:b3:be mscb->apfMsApVapId = 2
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.366: 00:24:d6:97:b3:be dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 220 mscb->apfMsLwappMwarInet.ipv4.addr = 176217288
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.366: 00:24:d6:97:b3:be mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = 176325157 mscb->apfMsLwappLradPort = 9385
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.371: 00:24:d6:97:b3:be Received EAPOL EAPPKT from mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.371: 00:24:d6:97:b3:be Received EAP Response from mobile 00:24:d6:97:b3:be (EAP Id 223, EAP Type 13)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.371: 00:24:d6:97:b3:be Resetting reauth count 0 to 0 for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.371: 00:24:d6:97:b3:be Entering Backend Auth Response state for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.372: 00:24:d6:97:b3:be Processing Access-Challenge for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.372: 00:24:d6:97:b3:be Entering Backend Auth Req state (id=224) for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.372: 00:24:d6:97:b3:be Sending EAP Request from AAA to mobile 00:24:d6:97:b3:be (EAP Id 224)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.372: 00:24:d6:97:b3:be Reusing allocated memory for EAP Pkt for retransmission to mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.372: 00:24:d6:97:b3:be mscb->apfMsLwappLradNhMac = 00:00:0c:07:ac:dc mscb->apfMsLradSlotId = 1 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.372: 00:24:d6:97:b3:be mscb->apfMsBssid = 18:33:9d:f0:21:80 mscb->apfMsAddress = 00:24:d6:97:b3:be mscb->apfMsApVapId = 2
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.372: 00:24:d6:97:b3:be dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 220 mscb->apfMsLwappMwarInet.ipv4.addr = 176217288
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.372: 00:24:d6:97:b3:be mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = 176325157 mscb->apfMsLwappLradPort = 9385
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.375: 00:24:d6:97:b3:be Received EAPOL EAPPKT from mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.375: 00:24:d6:97:b3:be Received EAP Response from mobile 00:24:d6:97:b3:be (EAP Id 224, EAP Type 13)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.375: 00:24:d6:97:b3:be Resetting reauth count 0 to 0 for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.375: 00:24:d6:97:b3:be Entering Backend Auth Response state for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.389: 00:24:d6:97:b3:be Processing Access-Challenge for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.389: 00:24:d6:97:b3:be Entering Backend Auth Req state (id=225) for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.389: 00:24:d6:97:b3:be Sending EAP Request from AAA to mobile 00:24:d6:97:b3:be (EAP Id 225)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.389: 00:24:d6:97:b3:be Reusing allocated memory for EAP Pkt for retransmission to mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.389: 00:24:d6:97:b3:be mscb->apfMsLwappLradNhMac = 00:00:0c:07:ac:dc mscb->apfMsLradSlotId = 1 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.389: 00:24:d6:97:b3:be mscb->apfMsBssid = 18:33:9d:f0:21:80 mscb->apfMsAddress = 00:24:d6:97:b3:be mscb->apfMsApVapId = 2
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.389: 00:24:d6:97:b3:be dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 220 mscb->apfMsLwappMwarInet.ipv4.addr = 176217288
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.389: 00:24:d6:97:b3:be mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = 176325157 mscb->apfMsLwappLradPort = 9385
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.391: 00:24:d6:97:b3:be Received EAPOL EAPPKT from mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.391: 00:24:d6:97:b3:be Received EAP Response from mobile 00:24:d6:97:b3:be (EAP Id 225, EAP Type 13)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.391: 00:24:d6:97:b3:be Resetting reauth count 0 to 0 for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.391: 00:24:d6:97:b3:be Entering Backend Auth Response state for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Processing Access-Accept for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Resetting web IPv4 acl from 255 to 255
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Resetting web IPv4 Flex acl from 65535 to 65535
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Username entry ([email protected]) created for mobile, length = 253
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Username entry ([email protected]) created in mscb for mobile, length = 253
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be override for default ap group, marking intgrp NULL
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Applying Interface policy on Mobile, role Unassociated. Ms NAC State 2 Quarantine Vlan 0 Access Vlan 220
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Re-applying interface policy for client
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be 0.0.0.0 8021X_REQD (3) Changing IPv4 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2219)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be 0.0.0.0 8021X_REQD (3) Changing IPv6 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2240)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be apfApplyWlanPolicy: Retaining the ACL recieved in AAA attributes 1 on mobile
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be apfApplyWlanPolicy: Apply WLAN Policy over PMIPv6 Client Mobility Type
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Inserting AAA Override struct for mobile
MAC: 00:24:d6:97:b3:be, source 4
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Setting re-auth timeout to 1800 seconds, got from WLAN config.
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Station 00:24:d6:97:b3:be setting dot1x reauth timeout = 1800
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Creating a PKC PMKID Cache entry for station 00:24:d6:97:b3:be (RSN 2)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Resetting MSCB PMK Cache Entry 0 for station 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Setting active key cache index 8 ---> 8
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Setting active key cache index 8 ---> 0
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Adding BSSID 18:33:9d:f0:21:8e to PMKID cache at index 0 for station 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: New PMKID: (16)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: [0000] 6f d1 ce 84 08 74 41 a5 06 6b 89 02 c9 e9 f8 c8
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Disabling re-auth since PMK lifetime can take care of same.
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be unsetting PmkIdValidatedByAp
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Client in Posture Reqd state. PMK cache not updated.
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Sending EAP-Success to mobile 00:24:d6:97:b3:be (EAP Id 225)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be mscb->apfMsLwappLradNhMac = 00:00:0c:07:ac:dc mscb->apfMsLradSlotId = 1 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be mscb->apfMsBssid = 18:33:9d:f0:21:80 mscb->apfMsAddress = 00:24:d6:97:b3:be mscb->apfMsApVapId = 2
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 220 mscb->apfMsLwappMwarInet.ipv4.addr = 176217288
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = 176325157 mscb->apfMsLwappLradPort = 9385
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Freeing AAACB from Dot1xCB as AAA auth is done for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be EAPOL Header:
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00000000: 02 03 5f 00 .._.
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Found an cache entry for BSSID 18:33:9d:f0:21:8e in PMKID cache at index 0 of station 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Found an cache entry for BSSID 18:33:9d:f0:21:8e in PMKID cache at index 0 of station 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: Including PMKID in M1 (16)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: [0000] 6f d1 ce 84 08 74 41 a5 06 6b 89 02 c9 e9 f8 c8
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Starting key exchange to mobile 00:24:d6:97:b3:be, data packets will be dropped
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Sending EAPOL-Key Message to mobile 00:24:d6:97:b3:be
state INITPMK (message 1), replay counter 00.00.00.00.00.00.00.00
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Sending EAPOL-Key Message to mobile 00:24:d6:97:b3:be
state INITPMK (message 1), replay counter 00.00.00.00.00.00.00.00
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Reusing allocated memory for EAP Pkt for retransmission to mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be mscb->apfMsLwappLradNhMac = 00:00:0c:07:ac:dc mscb->apfMsLradSlotId = 1 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be mscb->apfMsBssid = 18:33:9d:f0:21:80 mscb->apfMsAddress = 00:24:d6:97:b3:be mscb->apfMsApVapId = 2
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 220 mscb->apfMsLwappMwarInet.ipv4.addr = 176217288
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = 176325157 mscb->apfMsLwappLradPort = 9385
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Entering Backend Auth Success state (id=225) for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Received Auth Success while in Authenticating state for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be dot1x - moving mobile 00:24:d6:97:b3:be into Authenticated state
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.414: 00:24:d6:97:b3:be Received EAPOL-Key from mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.414: 00:24:d6:97:b3:be Received EAPOL-key in PTK_START state (message 2) from mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.414: 00:24:d6:97:b3:be PMK: Sending cache add
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.414: 00:24:d6:97:b3:be Stopping retransmission timer for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.414: 00:24:d6:97:b3:be EAPOL Header:
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.414: 00000000: 02 03 5f 00 .._.
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.414: 00:24:d6:97:b3:be Sending EAPOL-Key Message to mobile 00:24:d6:97:b3:be
state PTKINITNEGOTIATING (message 3), replay counter 00.00.00.00.00.00.00.01
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.414: 00:24:d6:97:b3:be Sending EAPOL-Key Message to mobile 00:24:d6:97:b3:be
state PTKINITNEGOTIATING (message 3), replay counter 00.00.00.00.00.00.00.01
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.414: 00:24:d6:97:b3:be Reusing allocated memory for EAP Pkt for retransmission to mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.414: 00:24:d6:97:b3:be mscb->apfMsLwappLradNhMac = 00:00:0c:07:ac:dc mscb->apfMsLradSlotId = 1 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.414: 00:24:d6:97:b3:be mscb->apfMsBssid = 18:33:9d:f0:21:80 mscb->apfMsAddress = 00:24:d6:97:b3:be mscb->apfMsApVapId = 2
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.414: 00:24:d6:97:b3:be dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 220 mscb->apfMsLwappMwarInet.ipv4.addr = 176217288
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.414: 00:24:d6:97:b3:be mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = 176325157 mscb->apfMsLwappLradPort = 9385
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be Received EAPOL-Key from mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be Received EAPOL-key in PTKINITNEGOTIATING state (message 4) from mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be Stopping retransmission timer for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be Freeing EAP Retransmit Bufer for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be apfMs1xStateInc
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be 0.0.0.0 8021X_REQD (3) Change state to L2AUTHCOMPLETE (4) last state 8021X_REQD (3)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be Central switch is FALSE
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be Sending the Central Auth Info
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be Central Auth Info Allocated PMKLen = 32
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: EapolReplayCounter: 00 00 00 00 00 00 00 01
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: EapolReplayCounter: 00 00 00 00 00 00 00 01
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be PMK: pmkActiveIndex = 0
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be EapolReplayCounter: 00 00 00 00 00 00 00 01
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be msAssocTypeFlagsMsb = 0 msAssocTypeFlagsLsb = 2
apfMsEntryType = 0 apfMsEapType = 13
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be 0.0.0.0 L2AUTHCOMPLETE (4) DHCP required on AP 18:33:9d:f0:21:80 vapId 2 apVapId 2for this client
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be Not Using WMM Compliance code qosCap 00
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be 0.0.0.0 L2AUTHCOMPLETE (4) Plumbed mobile LWAPP rule on AP 18:33:9d:f0:21:80 vapId 2 apVapId 2 flex-acl-name:POSTURE_REDIRECT_ACL
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be 0.0.0.0 L2AUTHCOMPLETE (4) Change state to DHCP_REQD (7) last state L2AUTHCOMPLETE (4)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be 0.0.0.0 DHCP_REQD (7) pemAdvanceState2 6166, Adding TMP rule
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be 0.0.0.0 DHCP_REQD (7) Adding Fast Path rule
type = Airespace AP - Learn IP address
on AP 18:33:9d:f0:21:80, slot 1, interface = 1, QOS = 0
IPv4 ACL ID = 255, IPv
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be 0.0.0.0 DHCP_REQD (7) Fast Path rule (contd...) 802.1P = 0, DSCP = 0, TokenID = 64206 Local Bridging Vlan = 220, Local Bridging intf id = 0
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be 0.0.0.0 DHCP_REQD (7) Successfully plumbed mobile rule (IPv4 ACL ID 255, IPv6 ACL ID 255, L2 ACL ID 255)
*apfReceiveTask: Aug 12 10:58:24.418: 00:24:d6:97:b3:be 0.0.0.0 DHCP_REQD (7) State Update from Mobility-Incomplete to Mobility-Complete, mobility role=Local, client state=APF_MS_STATE_ASSOCIATED
*apfReceiveTask: Aug 12 10:58:24.418: 00:24:d6:97:b3:be 0.0.0.0 DHCP_REQD (7) pemAdvanceState2 5761, Adding TMP rule
*apfReceiveTask: Aug 12 10:58:24.418: 00:24:d6:97:b3:be 0.0.0.0 DHCP_REQD (7) Replacing Fast Path rule
type = Airespace AP - Learn IP address
on AP 18:33:9d:f0:21:80, slot 1, interface = 1, QOS = 0
IPv4 ACL ID = 255,
*apfReceiveTask: Aug 12 10:58:24.418: 00:24:d6:97:b3:be 0.0.0.0 DHCP_REQD (7) Fast Path rule (contd...) 802.1P = 0, DSCP = 0, TokenID = 64206 Local Bridging Vlan = 220, Local Bridging intf id = 0
*apfReceiveTask: Aug 12 10:58:24.418: 00:24:d6:97:b3:be 0.0.0.0 DHCP_REQD (7) Successfully plumbed mobile rule (IPv4 ACL ID 255, IPv6 ACL ID 255, L2 ACL ID 255)
*pemReceiveTask: Aug 12 10:58:24.418: 00:24:d6:97:b3:be 0.0.0.0 Added NPU entry of type 9, dtlFlags 0x0
*pemReceiveTask: Aug 12 10:58:24.418: 00:24:d6:97:b3:be 0.0.0.0 Added NPU entry of type 9, dtlFlags 0x0
*spamApTask6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be spamEncodeCentralAuthInoMsPayload: msAssocTypeFlagsMsb = 0 msAssocTypeFlagsLsb = 2
apfMsEntryType = 0 pmkLen = 32
*DHCP Socket Task: Aug 12 10:58:24.546: 00:24:d6:97:b3:be DHCP received op BOOTREPLY (2) (len 325,vlan 220, port 1, encap 0xec03)
*DHCP Socket Task: Aug 12 10:58:24.546: 00:24:d6:97:b3:be DHCP setting server from ACK (server 10.0.17.85, yiaddr 10.130.130.120)
*DHCP Socket Task: Aug 12 10:58:24.548: 00:24:d6:97:b3:be 10.130.130.120 DHCP_REQD (7) Change state to WEBAUTH_REQD (8) last state DHCP_REQD (7)
*DHCP Socket Task: Aug 12 10:58:24.548: 00:24:d6:97:b3:be 10.130.130.120 WEBAUTH_REQD (8) pemAdvanceState2 6671, Adding TMP rule
*DHCP Socket Task: Aug 12 10:58:24.548: 00:24:d6:97:b3:be 10.130.130.120 WEBAUTH_REQD (8) Replacing Fast Path rule
type = Airespace AP Client - ACL passthru
on AP 18:33:9d:f0:21:80, slot 1, interface = 1, QOS = 0
IPv4 A
*DHCP Socket Task: Aug 12 10:58:24.548: 00:24:d6:97:b3:be 10.130.130.120 WEBAUTH_REQD (8) Fast Path rule (contd...) 802.1P = 0, DSCP = 0, TokenID = 64206 Local Bridging Vlan = 220, Local Bridging intf id = 0
*DHCP Socket Task: Aug 12 10:58:24.548: 00:24:d6:97:b3:be 10.130.130.120 WEBAUTH_REQD (8) Successfully plumbed mobile rule (IPv4 ACL ID 1, IPv6 ACL ID 255, L2 ACL ID 255)
*DHCP Socket Task: Aug 12 10:58:24.548: 00:24:d6:97:b3:be Plumbing web-auth redirect rule due to user logout
*DHCP Socket Task: Aug 12 10:58:24.548: 00:24:d6:97:b3:be Assigning Address 10.130.130.120 to mobile
*DHCP Socket Task: Aug 12 10:58:24.548: 00:24:d6:97:b3:be DHCP success event for client. Clearing dhcp failure count for interface management.
*DHCP Socket Task: Aug 12 10:58:24.548: 00:24:d6:97:b3:be DHCP success event for client. Clearing dhcp failure count for interface management.
*pemReceiveTask: Aug 12 10:58:24.548: 00:24:d6:97:b3:be 10.130.130.120 Added NPU entry of type 2, dtlFlags 0x0
*IPv6_Msg_Task: Aug 12 10:58:25.330: 00:24:d6:97:b3:be Pushing IPv6 Vlan Intf ID 0: fe80:0000:0000:0000:f524:1910:69f0:9482 , and MAC: 00:24:D6:97:B3:BE , Binding to Data Plane. SUCCESS !! dhcpv6bitmap 0
*IPv6_Msg_Task: Aug 12 10:58:25.330: 00:24:d6:97:b3:be Link Local address fe80::f524:1910:69f0:9482 updated to mscb. Not Advancing pem state.Current state: mscb in apfMsMmInitial mobility state and client state APF_MS_STATE_A
*DHCP Socket Task: Aug 12 10:58:28.581: 00:24:d6:97:b3:be DHCP received op BOOTREPLY (2) (len 308,vlan 220, port 1, encap 0xec03)
*DHCP Socket Task: Aug 12 10:58:28.589: 00:24:d6:97:b3:be DHCP received op BOOTREPLY (2) (len 308,vlan 220, port 1, encap 0xec03)
*DHCP Socket Task: Aug 12 11:00:07.959: 00:24:d6:97:b3:be DHCP received op BOOTREPLY (2) (len 308,vlan 220, port 1, encap 0xec03)
*DHCP Socket Task: Aug 12 11:00:07.967: 00:24:d6:97:b3:be DHCP received op BOOTREPLY (2) (len 308,vlan 220, port 1, encap 0xec03)
*DHCP Socket Task: Aug 12 11:01:59.153: 00:24:d6:97:b3:be DHCP received op BOOTREPLY (2) (len 308,vlan 220, port 1, encap 0xec03)
Can you see any obvious reason why the NAC agent wont pop up?
Thanks
Mario -
IPhones not taking ipv4 addresses on Unified Wireless (WLC 5508 and AP 3602)
This is a really odd one...
Earlier this week we started having issues with our BYOD wireless network (802.1x, WPA2+AES) but only with Apple devices (iphone and ipad). Employees with Android or Windows phones are not having any problems at all.
A brief summary of what's observable for the issue:
Radius authentication succeeds (PASS observable in ACS logs)
IPhone status viewed on both controllers (foreign anchor in DMZ as well as corporate WLC) shows phone associated.
Debug client output shows an IPv4 address is actually being assigned to the phone however it appears to ignore it and restart the DHCP request process so debug output shows what looks to be a loop of DHCP request and offer stages.
Infrastructure notes
Cisco WLC 5508s are all running 7.4.121.0 (tried rolling back to 7.2.110.0 .....didn't help)
APs are all 3602I-N-K9
DHCP for the BYOD network is running on the anchor in the DMZ however this was temporarily moved to a switch (had no effect).
Any ideas?
DHCP Loop:
*mmListen: Apr 30 11:44:50.476: a4:c3:61:7a:1a:4f 0.0.0.0 RUN (20) Fast Path rule (contd...) 802.1P = 0, DSCP = 0, TokenID = 15206 Local Bridging Vlan = 93, Local Bridging intf id = 12
*mmListen: Apr 30 11:44:50.476: a4:c3:61:7a:1a:4f 0.0.0.0 RUN (20) Successfully plumbed mobile rule (IPv4 ACL ID 255, IPv6 ACL ID 255)
*pemReceiveTask: Apr 30 11:44:50.476: a4:c3:61:7a:1a:4f Set bi-dir guest tunnel for a4:c3:61:7a:1a:4f as in Export Anchor role
*pemReceiveTask: Apr 30 11:44:50.476: a4:c3:61:7a:1a:4f 0.0.0.0 Added NPU entry of type 1, dtlFlags 0x4
*pemReceiveTask: Apr 30 11:44:50.476: a4:c3:61:7a:1a:4f Pushing IPv6: fe80:0000:0000:0000: 0c00:0c94:459e:a9db , and MAC: A4:C3:61:7A:1A:4F , Binding to Data Plane. SUCCESS !!
*DHCP Socket Task: Apr 30 11:44:50.479: a4:c3:61:7a:1a:4f DHCP received op BOOTREQUEST (1) (len 308,vlan 92, port 13, encap 0xec05)
*DHCP Socket Task: Apr 30 11:44:50.479: a4:c3:61:7a:1a:4f DHCP selecting relay 1 - control block settings:
dhcpServer: 172.24.13.251, dhcpNetmask: 0.0.0.0,
dhcpGateway: 0.0.0.0, dhcpRelay: 172.24.16.251 VLAN: 93
*DHCP Socket Task: Apr 30 11:44:50.479: a4:c3:61:7a:1a:4f DHCP selected relay 1 - 172.24.13.251 (local address 172.24.16.251, gateway 172.24.16.254, VLAN 93, port 13)
*DHCP Socket Task: Apr 30 11:44:50.479: a4:c3:61:7a:1a:4f DHCP transmitting DHCP DISCOVER (1)
*DHCP Socket Task: Apr 30 11:44:50.479: a4:c3:61:7a:1a:4f DHCP op: BOOTREQUEST, htype: Ethernet, hlen: 6, hops: 1
*DHCP Socket Task: Apr 30 11:44:50.479: a4:c3:61:7a:1a:4f DHCP xid: 0x7e549f4a (2119475018), secs: 0, flags: 0
*DHCP Socket Task: Apr 30 11:44:50.479: a4:c3:61:7a:1a:4f DHCP chaddr: a4:c3:61:7a:1a:4f
*DHCP Socket Task: Apr 30 11:44:50.479: a4:c3:61:7a:1a:4f DHCP ciaddr: 0.0.0.0, yiaddr: 0.0.0.0
*DHCP Socket Task: Apr 30 11:44:50.479: a4:c3:61:7a:1a:4f DHCP siaddr: 0.0.0.0, giaddr: 172.24.16.251
*DHCP Socket Task: Apr 30 11:44:50.479: a4:c3:61:7a:1a:4f DHCP selecting relay 2 - control block settings:
dhcpServer: 172.24.13.251, dhcpNetmask: 0.0.0.0,
dhcpGateway: 0.0.0.0, dhcpRelay: 172.24.16.251 VLAN: 93
*DHCP Socket Task: Apr 30 11:44:50.479: a4:c3:61:7a:1a:4f DHCP selected relay 2 - NONE
*DHCP Proxy Task: Apr 30 11:44:50.479: a4:c3:61:7a:1a:4f DHCP received op BOOTREPLY (2) (len 572,vlan 0, port 0, encap 0x0)
*DHCP Proxy Task: Apr 30 11:44:50.479: a4:c3:61:7a:1a:4f DHCP sending packet in EoIP tunnel to foreign 10.65.31.8 (len 346)
*DHCP Proxy Task: Apr 30 11:44:50.479: a4:c3:61:7a:1a:4f DHCP transmitting DHCP OFFER (2)
*DHCP Proxy Task: Apr 30 11:44:50.479: a4:c3:61:7a:1a:4f DHCP op: BOOTREPLY, htype: Ethernet, hlen: 6, hops: 0
*DHCP Proxy Task: Apr 30 11:44:50.479: a4:c3:61:7a:1a:4f DHCP xid: 0x7e549f4a (2119475018), secs: 0, flags: 0
*DHCP Proxy Task: Apr 30 11:44:50.480: a4:c3:61:7a:1a:4f DHCP chaddr: a4:c3:61:7a:1a:4f
*DHCP Proxy Task: Apr 30 11:44:50.480: a4:c3:61:7a:1a:4f DHCP ciaddr: 0.0.0.0, yiaddr: 172.24.16.102
*DHCP Proxy Task: Apr 30 11:44:50.480: a4:c3:61:7a:1a:4f DHCP siaddr: 0.0.0.0, giaddr: 0.0.0.0
*DHCP Proxy Task: Apr 30 11:44:50.480: a4:c3:61:7a:1a:4f DHCP server id: 0.0.0.0 rcvd server id: 172.24.13.251
*DHCP Socket Task: Apr 30 11:44:51.649: a4:c3:61:7a:1a:4f DHCP received op BOOTREQUEST (1) (len 308,vlan 92, port 13, encap 0xec05)
*DHCP Socket Task: Apr 30 11:44:51.649: a4:c3:61:7a:1a:4f DHCP selecting relay 1 - control block settings:
dhcpServer: 172.24.13.251, dhcpNetmask: 0.0.0.0,
dhcpGateway: 0.0.0.0, dhcpRelay: 172.24.16.251 VLAN: 93
*DHCP Socket Task: Apr 30 11:44:51.649: a4:c3:61:7a:1a:4f DHCP selected relay 1 - 172.24.13.251 (local address 172.24.16.251, gateway 172.24.16.254, VLAN 93, port 13)
*DHCP Socket Task: Apr 30 11:44:51.649: a4:c3:61:7a:1a:4f DHCP transmitting DHCP DISCOVER (1)
*DHCP Socket Task: Apr 30 11:44:51.649: a4:c3:61:7a:1a:4f DHCP op: BOOTREQUEST, htype: Ethernet, hlen: 6, hops: 1
*DHCP Socket Task: Apr 30 11:44:51.649: a4:c3:61:7a:1a:4f DHCP xid: 0x7e549f4a (2119475018), secs: 1, flags: 0
*DHCP Socket Task: Apr 30 11:44:51.649: a4:c3:61:7a:1a:4f DHCP chaddr: a4:c3:61:7a:1a:4f
*DHCP Socket Task: Apr 30 11:44:51.649: a4:c3:61:7a:1a:4f DHCP ciaddr: 0.0.0.0, yiaddr: 0.0.0.0
*DHCP Socket Task: Apr 30 11:44:51.649: a4:c3:61:7a:1a:4f DHCP siaddr: 0.0.0.0, giaddr: 172.24.16.251
*DHCP Socket Task: Apr 30 11:44:51.649: a4:c3:61:7a:1a:4f DHCP selecting relay 2 - control block settings:
dhcpServer: 172.24.13.251, dhcpNetmask: 0.0.0.0,
dhcpGateway: 0.0.0.0, dhcpRelay: 172.24.16.251 VLAN: 93
*DHCP Socket Task: Apr 30 11:44:51.649: a4:c3:61:7a:1a:4f DHCP selected relay 2 - NONE
*DHCP Proxy Task: Apr 30 11:44:51.649: a4:c3:61:7a:1a:4f DHCP received op BOOTREPLY (2) (len 572,vlan 0, port 0, encap 0x0)
*DHCP Proxy Task: Apr 30 11:44:51.649: a4:c3:61:7a:1a:4f DHCP sending packet in EoIP tunnel to foreign 10.65.31.8 (len 346)
*DHCP Proxy Task: Apr 30 11:44:51.649: a4:c3:61:7a:1a:4f DHCP transmitting DHCP OFFER (2)
*DHCP Proxy Task: Apr 30 11:44:51.649: a4:c3:61:7a:1a:4f DHCP op: BOOTREPLY, htype: Ethernet, hlen: 6, hops: 0
*DHCP Proxy Task: Apr 30 11:44:51.650: a4:c3:61:7a:1a:4f DHCP xid: 0x7e549f4a (2119475018), secs: 0, flags: 0
*DHCP Proxy Task: Apr 30 11:44:51.650: a4:c3:61:7a:1a:4f DHCP chaddr: a4:c3:61:7a:1a:4f
*DHCP Proxy Task: Apr 30 11:44:51.650: a4:c3:61:7a:1a:4f DHCP ciaddr: 0.0.0.0, yiaddr: 172.24.16.102
*DHCP Proxy Task: Apr 30 11:44:51.650: a4:c3:61:7a:1a:4f DHCP siaddr: 0.0.0.0, giaddr: 0.0.0.0
*DHCP Proxy Task: Apr 30 11:44:51.650: a4:c3:61:7a:1a:4f DHCP server id: 0.0.0.0 rcvd server id: 172.24.13.251
*DHCP Socket Task: Apr 30 11:44:53.754: a4:c3:61:7a:1a:4f DHCP received op BOOTREQUEST (1) (len 308,vlan 92, port 13, encap 0xec05)
*DHCP Socket Task: Apr 30 11:44:53.755: a4:c3:61:7a:1a:4f DHCP selecting relay 1 - control block settings:
dhcpServer: 172.24.13.251, dhcpNetmask: 0.0.0.0,
dhcpGateway: 0.0.0.0, dhcpRelay: 172.24.16.251 VLAN: 93
*DHCP Socket Task: Apr 30 11:44:53.755: a4:c3:61:7a:1a:4f DHCP selected relay 1 - 172.24.13.251 (local address 172.24.16.251, gateway 172.24.16.254, VLAN 93, port 13)
*DHCP Socket Task: Apr 30 11:44:53.755: a4:c3:61:7a:1a:4f DHCP transmitting DHCP DISCOVER (1)
*DHCP Socket Task: Apr 30 11:44:53.755: a4:c3:61:7a:1a:4f DHCP op: BOOTREQUEST, htype: Ethernet, hlen: 6, hops: 1
*DHCP Socket Task: Apr 30 11:44:53.755: a4:c3:61:7a:1a:4f DHCP xid: 0x7e549f4a (2119475018), secs: 3, flags: 0
*DHCP Socket Task: Apr 30 11:44:53.755: a4:c3:61:7a:1a:4f DHCP chaddr: a4:c3:61:7a:1a:4f
*DHCP Socket Task: Apr 30 11:44:53.755: a4:c3:61:7a:1a:4f DHCP ciaddr: 0.0.0.0, yiaddr: 0.0.0.0
*DHCP Socket Task: Apr 30 11:44:53.755: a4:c3:61:7a:1a:4f DHCP siaddr: 0.0.0.0, giaddr: 172.24.16.251
*DHCP Socket Task: Apr 30 11:44:53.755: a4:c3:61:7a:1a:4f DHCP selecting relay 2 - control block settings:
dhcpServer: 172.24.13.251, dhcpNetmask: 0.0.0.0,
dhcpGateway: 0.0.0.0, dhcpRelay: 172.24.16.251 VLAN: 93
*DHCP Socket Task: Apr 30 11:44:53.755: a4:c3:61:7a:1a:4f DHCP selected relay 2 - NONE
*DHCP Proxy Task: Apr 30 11:44:53.755: a4:c3:61:7a:1a:4f DHCP received op BOOTREPLY (2) (len 572,vlan 0, port 0, encap 0x0)
*DHCP Proxy Task: Apr 30 11:44:53.755: a4:c3:61:7a:1a:4f DHCP sending packet in EoIP tunnel to foreign 10.65.31.8 (len 346)
*DHCP Proxy Task: Apr 30 11:44:53.755: a4:c3:61:7a:1a:4f DHCP transmitting DHCP OFFER (2)
*DHCP Proxy Task: Apr 30 11:44:53.755: a4:c3:61:7a:1a:4f DHCP op: BOOTREPLY, htype: Ethernet, hlen: 6, hops: 0
*DHCP Proxy Task: Apr 30 11:44:53.755: a4:c3:61:7a:1a:4f DHCP xid: 0x7e549f4a (2119475018), secs: 0, flags: 0
*DHCP Proxy Task: Apr 30 11:44:53.755: a4:c3:61:7a:1a:4f DHCP chaddr: a4:c3:61:7a:1a:4f
*DHCP Proxy Task: Apr 30 11:44:53.755: a4:c3:61:7a:1a:4f DHCP ciaddr: 0.0.0.0, yiaddr: 172.24.16.102
*DHCP Proxy Task: Apr 30 11:44:53.755: a4:c3:61:7a:1a:4f DHCP siaddr: 0.0.0.0, giaddr: 0.0.0.0
*DHCP Proxy Task: Apr 30 11:44:53.755: a4:c3:61:7a:1a:4f DHCP server id: 0.0.0.0 rcvd server id: 172.24.13.251
*DHCP Socket Task: Apr 30 11:44:58.594: a4:c3:61:7a:1a:4f DHCP received op BOOTREQUEST (1) (len 308,vlan 92, port 13, encap 0xec05)
*DHCP Socket Task: Apr 30 11:44:58.594: a4:c3:61:7a:1a:4f DHCP selecting relay 1 - control block settings:
dhcpServer: 172.24.13.251, dhcpNetmask: 0.0.0.0,
dhcpGateway: 0.0.0.0, dhcpRelay: 172.24.16.251 VLAN: 93
*DHCP Socket Task: Apr 30 11:44:58.594: a4:c3:61:7a:1a:4f DHCP selected relay 1 - 172.24.13.251 (local address 172.24.16.251, gateway 172.24.16.254, VLAN 93, port 13)
*DHCP Socket Task: Apr 30 11:44:58.594: a4:c3:61:7a:1a:4f DHCP transmitting DHCP DISCOVER (1)
*DHCP Socket Task: Apr 30 11:44:58.594: a4:c3:61:7a:1a:4f DHCP op: BOOTREQUEST, htype: Ethernet, hlen: 6, hops: 1
*DHCP Socket Task: Apr 30 11:44:58.594: a4:c3:61:7a:1a:4f DHCP xid: 0x7e549f4a (2119475018), secs: 8, flags: 0
*DHCP Socket Task: Apr 30 11:44:58.594: a4:c3:61:7a:1a:4f DHCP chaddr: a4:c3:61:7a:1a:4f
*DHCP Socket Task: Apr 30 11:44:58.594: a4:c3:61:7a:1a:4f DHCP ciaddr: 0.0.0.0, yiaddr: 0.0.0.0
*DHCP Socket Task: Apr 30 11:44:58.594: a4:c3:61:7a:1a:4f DHCP siaddr: 0.0.0.0, giaddr: 172.24.16.251
*DHCP Socket Task: Apr 30 11:44:58.595: a4:c3:61:7a:1a:4f DHCP selecting relay 2 - control block settings:
dhcpServer: 172.24.13.251, dhcpNetmask: 0.0.0.0,
dhcpGateway: 0.0.0.0, dhcpRelay: 172.24.16.251 VLAN: 93
*DHCP Socket Task: Apr 30 11:44:58.595: a4:c3:61:7a:1a:4f DHCP selected relay 2 - NONE
*DHCP Proxy Task: Apr 30 11:44:58.595: a4:c3:61:7a:1a:4f DHCP received op BOOTREPLY (2) (len 572,vlan 0, port 0, encap 0x0)
*DHCP Proxy Task: Apr 30 11:44:58.595: a4:c3:61:7a:1a:4f DHCP sending packet in EoIP tunnel to foreign 10.65.31.8 (len 346)
*DHCP Proxy Task: Apr 30 11:44:58.595: a4:c3:61:7a:1a:4f DHCP transmitting DHCP OFFER (2)
*DHCP Proxy Task: Apr 30 11:44:58.595: a4:c3:61:7a:1a:4f DHCP op: BOOTREPLY, htype: Ethernet, hlen: 6, hops: 0
*DHCP Proxy Task: Apr 30 11:44:58.595: a4:c3:61:7a:1a:4f DHCP xid: 0x7e549f4a (2119475018), secs: 0, flags: 0
*DHCP Proxy Task: Apr 30 11:44:58.595: a4:c3:61:7a:1a:4f DHCP chaddr: a4:c3:61:7a:1a:4f
*DHCP Proxy Task: Apr 30 11:44:58.595: a4:c3:61:7a:1a:4f DHCP ciaddr: 0.0.0.0, yiaddr: 172.24.16.102
*DHCP Proxy Task: Apr 30 11:44:58.595: a4:c3:61:7a:1a:4f DHCP siaddr: 0.0.0.0, giaddr: 0.0.0.0
*DHCP Proxy Task: Apr 30 11:44:58.595: a4:c3:61:7a:1a:4f DHCP server id: 0.0.0.0 rcvd server id: 172.24.13.251
*DHCP Socket Task: Apr 30 11:45:07.059: a4:c3:61:7a:1a:4f DHCP received op BOOTREQUEST (1) (len 308,vlan 92, port 13, encap 0xec05)
*DHCP Socket Task: Apr 30 11:45:07.059: a4:c3:61:7a:1a:4f DHCP selecting relay 1 - control block settings:
dhcpServer: 172.24.13.251, dhcpNetmask: 0.0.0.0,Thanks Scott, here you go...
On Foreign:
WLAN Identifier.................................. 2
Profile Name..................................... BAI-Beta
Network Name (SSID).............................. BAI-Beta
Status........................................... Enabled
MAC Filtering.................................... Disabled
Broadcast SSID................................... Disabled
AAA Policy Override.............................. Disabled
Network Admission Control
Client Profiling Status ....................... Disabled
DHCP ......................................... Disabled
HTTP ......................................... Disabled
Radius-NAC State............................... Disabled
SNMP-NAC State................................. Disabled
Quarantine VLAN................................ 0
Maximum number of Associated Clients............. 0
Maximum number of Clients per AP Radio........... 200
Number of Active Clients......................... 42
Exclusionlist Timeout............................ 60 seconds
Session Timeout.................................. 86400 seconds
User Idle Timeout................................ 300 seconds
--More-- or (q)uit
User Idle Threshold.............................. 0 Bytes
NAS-identifier................................... CHTWLC
CHD per WLAN..................................... Enabled
Webauth DHCP exclusion........................... Disabled
Interface........................................ management
Multicast Interface.............................. Not Configured
WLAN IPv4 ACL.................................... unconfigured
WLAN IPv6 ACL.................................... unconfigured
mDNS Status...................................... Enabled
mDNS Profile Name................................ default-mdns-profile
DHCP Server...................................... Default
DHCP Address Assignment Required................. Enabled
Static IP client tunneling....................... Disabled
PMIPv6 Mobility Type............................. none
Quality of Service............................... Bronze
Per-SSID Rate Limits............................. Upstream Downstream
Average Data Rate................................ 0 0
Average Realtime Data Rate....................... 0 0
Burst Data Rate.................................. 0 0
Burst Realtime Data Rate......................... 0 0
Per-Client Rate Limits........................... Upstream Downstream
Average Data Rate................................ 0 0
Average Realtime Data Rate....................... 0 0
--More-- or (q)uit
Burst Data Rate.................................. 0 0
Burst Realtime Data Rate......................... 0 0
Scan Defer Priority.............................. 5,6
Scan Defer Time.................................. 100 milliseconds
WMM.............................................. Disabled
WMM UAPSD Compliant Client Support............... Disabled
Media Stream Multicast-direct.................... Disabled
CCX - AironetIe Support.......................... Enabled
CCX - Gratuitous ProbeResponse (GPR)............. Disabled
CCX - Diagnostics Channel Capability............. Disabled
Dot11-Phone Mode (7920).......................... Disabled
Wired Protocol................................... None
Passive Client Feature........................... Disabled
Peer-to-Peer Blocking Action..................... Disabled
Radio Policy..................................... All
DTIM period for 802.11a radio.................... 1
DTIM period for 802.11b radio.................... 1
Radius Servers
Authentication................................ 172.24.13.20 1812
Accounting.................................... Disabled
Dynamic Interface............................. Disabled
Dynamic Interface Priority.................... wlan
Local EAP Authentication......................... Disabled
--More-- or (q)uit
Security
802.11 Authentication:........................ Open System
FT Support.................................... Disabled
Static WEP Keys............................... Disabled
802.1X........................................ Disabled
Wi-Fi Protected Access (WPA/WPA2)............. Enabled
WPA (SSN IE)............................... Disabled
WPA2 (RSN IE).............................. Enabled
TKIP Cipher............................. Disabled
AES Cipher.............................. Enabled
Auth Key Management
802.1x.................................. Enabled
PSK..................................... Disabled
CCKM.................................... Disabled
FT-1X(802.11r).......................... Disabled
FT-PSK(802.11r)......................... Disabled
PMF-1X(802.11w)......................... Disabled
PMF-PSK(802.11w)........................ Disabled
FT Reassociation Timeout................... 20
FT Over-The-DS mode........................ Enabled
GTK Randomization.......................... Disabled
SKC Cache Support.......................... Disabled
--More-- or (q)uit
CCKM TSF Tolerance......................... 1000
WAPI.......................................... Disabled
Wi-Fi Direct policy configured................ Disabled
EAP-Passthrough............................... Disabled
CKIP ......................................... Disabled
Web Based Authentication...................... Disabled
Web-Passthrough............................... Disabled
Conditional Web Redirect...................... Disabled
Splash-Page Web Redirect...................... Disabled
Auto Anchor................................... Enabled
FlexConnect Local Switching................... Disabled
flexconnect Central Dhcp Flag................. Disabled
flexconnect nat-pat Flag...................... Disabled
flexconnect Dns Override Flag................. Disabled
FlexConnect Vlan based Central Switching ..... Disabled
FlexConnect Local Authentication.............. Disabled
FlexConnect Learn IP Address.................. Enabled
Client MFP.................................... Optional
PMF........................................... Disabled
PMF Association Comeback Time................. 1
PMF SA Query RetryTimeout..................... 200
Tkip MIC Countermeasure Hold-down Timer....... 60
AVC Visibilty.................................... Disabled
--More-- or (q)uit
AVC Profile Name................................. None
Flow Monitor Name................................ None
Call Snooping.................................... Disabled
Roamed Call Re-Anchor Policy..................... Disabled
SIP CAC Fail Send-486-Busy Policy................ Enabled
SIP CAC Fail Send Dis-Association Policy......... Disabled
KTS based CAC Policy............................. Disabled
Assisted Roaming Prediction Optimization......... Disabled
802.11k Neighbor List............................ Disabled
802.11k Neighbor List Dual Band.................. Disabled
Band Select...................................... Disabled
Load Balancing................................... Disabled
Multicast Buffer................................. Disabled
Mobility Anchor List
WLAN ID IP Address Status
2 172.24.13.251 Up
802.11u........................................ Disabled
MSAP Services.................................. Disabled
On Anchor:
WLAN Identifier.................................. 1
Profile Name..................................... BAI-Beta
Network Name (SSID).............................. BAI-Beta
Status........................................... Enabled
MAC Filtering.................................... Disabled
Broadcast SSID................................... Disabled
AAA Policy Override.............................. Disabled
Network Admission Control
Client Profiling Status ....................... Disabled
DHCP ......................................... Disabled
HTTP ......................................... Disabled
Radius-NAC State............................... Disabled
SNMP-NAC State................................. Disabled
Quarantine VLAN................................ 0
Maximum number of Associated Clients............. 0
Maximum number of Clients per AP Radio........... 200
Number of Active Clients......................... 48
Exclusionlist Timeout............................ 60 seconds
Session Timeout.................................. 86400 seconds
User Idle Timeout................................ 300 seconds
--More-- or (q)uit
User Idle Threshold.............................. 0 Bytes
NAS-identifier................................... CHADWLC01
CHD per WLAN..................................... Enabled
Webauth DHCP exclusion........................... Disabled
Interface........................................ bai-beta
Multicast Interface.............................. Not Configured
WLAN IPv4 ACL.................................... unconfigured
WLAN IPv6 ACL.................................... unconfigured
mDNS Status...................................... Enabled
mDNS Profile Name................................ default-mdns-profile
DHCP Server...................................... Default
DHCP Address Assignment Required................. Enabled
Static IP client tunneling....................... Disabled
PMIPv6 Mobility Type............................. none
Quality of Service............................... Bronze
Per-SSID Rate Limits............................. Upstream Downstream
Average Data Rate................................ 0 0
Average Realtime Data Rate....................... 0 0
Burst Data Rate.................................. 0 0
Burst Realtime Data Rate......................... 0 0
Per-Client Rate Limits........................... Upstream Downstream
Average Data Rate................................ 0 0
Average Realtime Data Rate....................... 0 0
--More-- or (q)uit
Burst Data Rate.................................. 0 0
Burst Realtime Data Rate......................... 0 0
Scan Defer Priority.............................. 5,6
Scan Defer Time.................................. 100 milliseconds
WMM.............................................. Disabled
WMM UAPSD Compliant Client Support............... Disabled
Media Stream Multicast-direct.................... Disabled
CCX - AironetIe Support.......................... Enabled
CCX - Gratuitous ProbeResponse (GPR)............. Disabled
CCX - Diagnostics Channel Capability............. Disabled
Dot11-Phone Mode (7920).......................... Disabled
Wired Protocol................................... None
Passive Client Feature........................... Disabled
Peer-to-Peer Blocking Action..................... Disabled
Radio Policy..................................... All
DTIM period for 802.11a radio.................... 1
DTIM period for 802.11b radio.................... 1
Radius Servers
Authentication................................ 172.24.13.20 1812
Accounting.................................... Disabled
Dynamic Interface............................. Disabled
Dynamic Interface Priority.................... wlan
Local EAP Authentication......................... Disabled
--More-- or (q)uit
Security
802.11 Authentication:........................ Open System
FT Support.................................... Disabled
Static WEP Keys............................... Disabled
802.1X........................................ Disabled
Wi-Fi Protected Access (WPA/WPA2)............. Enabled
WPA (SSN IE)............................... Disabled
WPA2 (RSN IE).............................. Enabled
TKIP Cipher............................. Disabled
AES Cipher.............................. Enabled
Auth Key Management
802.1x.................................. Enabled
PSK..................................... Disabled
CCKM.................................... Disabled
FT-1X(802.11r).......................... Disabled
FT-PSK(802.11r)......................... Disabled
PMF-1X(802.11w)......................... Disabled
PMF-PSK(802.11w)........................ Disabled
FT Reassociation Timeout................... 20
FT Over-The-DS mode........................ Enabled
GTK Randomization.......................... Disabled
SKC Cache Support.......................... Disabled
--More-- or (q)uit
CCKM TSF Tolerance......................... 1000
WAPI.......................................... Disabled
Wi-Fi Direct policy configured................ Disabled
EAP-Passthrough............................... Disabled
CKIP ......................................... Disabled
Web Based Authentication...................... Disabled
Web-Passthrough............................... Disabled
Conditional Web Redirect...................... Disabled
Splash-Page Web Redirect...................... Disabled
Auto Anchor................................... Enabled
FlexConnect Local Switching................... Disabled
flexconnect Central Dhcp Flag................. Disabled
flexconnect nat-pat Flag...................... Disabled
flexconnect Dns Override Flag................. Disabled
FlexConnect Vlan based Central Switching ..... Disabled
FlexConnect Local Authentication.............. Disabled
FlexConnect Learn IP Address.................. Enabled
Client MFP.................................... Optional
PMF........................................... Disabled
PMF Association Comeback Time................. 1
PMF SA Query RetryTimeout..................... 200
Tkip MIC Countermeasure Hold-down Timer....... 60
AVC Visibilty.................................... Disabled
--More-- or (q)uit
AVC Profile Name................................. None
Flow Monitor Name................................ None
Call Snooping.................................... Disabled
Roamed Call Re-Anchor Policy..................... Disabled
SIP CAC Fail Send-486-Busy Policy................ Enabled
SIP CAC Fail Send Dis-Association Policy......... Disabled
KTS based CAC Policy............................. Disabled
Assisted Roaming Prediction Optimization......... Disabled
802.11k Neighbor List............................ Disabled
802.11k Neighbor List Dual Band.................. Disabled
Band Select...................................... Disabled
Load Balancing................................... Disabled
Multicast Buffer................................. Disabled
Mobility Anchor List
WLAN ID IP Address Status
1 172.24.13.251 Up
802.11u........................................ Disabled
MSAP Services.................................. Disabled -
One WLC 5508, Multiple Sites/Networks
So I'm trying to think this design out in my head. Here is what I have:
Corp Office with a WLC 5508 configured with a management port and a guest WLAN port for guest wireless etc to the corp Layer 3 switch in a wireless VLAN, using 802.1q trunk of course. The WLC is configured to be a DHCP server for the Guest WLAN.
(Side note: the sites are connected using WAN routers at each location configured with bundled T3's and all routes are setup and each network successfully traverses to the other)
First phase will be to install 30 APs. 5 at the corporate office and 25 and two other sites. I'm using a class A network but have subnetted the networks so to speak to make each site have multiple VLANs using class C networks. I want to be able to implement the WLC 5508 at the corporate office and manage the APs centrally at all locations. The APs are already configured for lightweight mode and I have successfully configured 5 of them and connected.
My question is if I install the other 25 APs at the other 2 offsite locations and connect them to the network, will it automatically contact the WLC and get a DHCP address from the Corporate WLAN DHCP even though it is at another site? Am I overlooking a step or configuration method for this type of implementation?
Thanks for all contributions!Ok so I have configured my environment as suggested. I can see the new IP Address lease to the AP at my remote site on
the DHCP Server (Windows Server DHCP at the remote site). I can ping that IP from the Central office to the remote site however the WIreless Controller is not associating the AP at all. Although I can ping the AP from the WLC. I checked the logs and I dont see any association attempt from that IP or MACt. So here is what I have:
Central Site-
WLC 5508 With Internal DHCP for local APs
APs associating successfully
Remote Site
Windows DHCP with Option 43 Configured per Cisco AP Option 43 Whitepaper
AP 1142-Light-Weight attached to switchport (Wireless Vlan configured) and reachable via ping through all of network.
AP obtained IP from Windows DHCP from Wireless Scope I configured successfully.
So it doesn't seem the CAPWAP tunnel was built successfully. I do have an ASA 5520 in the environment but all traffic to remote sites is wide open as I do not block any ports so CAPWAP traffic should flow well.
Mission a step?
Dee -
Guest Wireless Tunnelling - DHCP Issue
Hi,
I'm attempting to implement Guest Anchor tunnelling between two WLC's but I've run into an odd issue I cannot find a clear answer to.
We have two 5508 WLC's, both Running 7.4.100.0.
The Guest Anchor Controller obviously resides in a DMZ, it's functionality has been proven by connecting an AP directly to it, and connecting the the guest WLAN.
The two controllers have been configured as Mobility Peers, the Mobility Tunnel between them is up (mping and eping both successful, status is up).
The Guest WLAN has been replicated on both controllers, I have set the Mobility Anchor on the WLAN. The Guest Anchor has itself as the mobility anchor and the Internal Controller has the Guest Anchor set.
DHCP is provided by the Guest Anchor's internal DHCP Server. DHCP Proxy is enabled on both Controllers, with the Option 82 format set to AP-MAC. Both Controllers WLAN settings are set to DHCP Server Override, pointed to the Management IP of the Guest Anchor and DHCP Addr. Assignment required.
The problem I'm experiencing is with connecting clients through the Internal WLC. The Client Associates to the Internal WLC and obtains a lease from the Guest Anchor and connects to the network. A few seconds later the client is dessociated from the internal controller. On every subsequent connection attempt, the client does not recieve a response to it's DHCP Requests, and hence ends up with an apipa address.
The Message logs on two controllers return the following errors:
INTERNAL CONTROLLER:
*apfReceiveTask: Jun 27 14:03:25.839: #APF-4-HANDOFF_END_RCVD: apf_mm.c:1626 Handoff end received in wrong role (peer Ip: 0.0.0.0, sender:GUEST_ANCHOR_IP, Role:0) for mobile Client_MAC
GUEST ANCHOR CONTROLLER:
*DHCP Server: Jun 27 14:03:14.466: #DHCP-4-REQIP_NOT_PRESENT: dhcpd.c:559 Received a packet without a requested ip!.
Has anyone else seen similar behaviour? Does anyone have an ideas what might be causing this?
Many Thanks,
PaulHi George,
Thanks for the reply.
The Guest WLAN on the Internal Controller is Anchored to the WLC in the DMZ. The Guest Anchor is anchored to itself.
There are only two controllers in the configuration, so breaking off one of the Anchors isn't really an option.
I have tested the Guest Anchor as a Standalone WLC by connecting an AP directly to it, in that configuration DHCP works as expected. -
WLC 5508: 802.1 AAA override; Authenication success no dynamic vlan assignment
WLC 5508: software version 7.0.98.0
Windows 7 Client
Radius Server: Fedora Core 13 / Freeradius with LDAP storage backend
I have followed the guide at http://www.cisco.com/en/US/tech/tk722/tk809/technologies_configuration_example09186a008076317c.shtml with respective to building the LDAP and free radius server. 802.1x authorization and authenication correctly work. The session keys are returned from the radius server and the wlc send the appropriate information for the client to generate the WEP key.
However, the WLC does not override the VLAN assignment, even though I was to believe I set everything up correctly. From the packet capture, you can see that verfication of client is authorized to use the WLAN returns the needed attributes:
AVP: l=4 t=Tunnel-Private-Group-Id(81): 10
AVP: l=6 t=Tunnel-Medium-Type(65): IEEE-802(6)
AVP: l=6 t=Tunnel-Type(64): VLAN(13)
I attached a packet capture and wlc config, any guidance toward the attributes that may be missing or not set correctly in the config would be most appreciated.Yes good catch, so I had one setting left off in freeradius that allowed the inner reply attributes back to the outer tunneled accept. I wrote up a medium high level config for any future viewers of this thread:
The following was tested and verified on a fedora 13 installation. This is a minimal setup; not meant for a "live" network (security issues with cleartext passwords, ldap not indexed properly for performance)
Install Packages
1. Install needed packages.
yum install openldap*
yum install freeradius*
2. Set the services to automatically start of system startup
chkconfig --level 2345 slapd on
chkconfig --level 2345 radiusd on
Configure and start LDAP
1. Copy the needed ladp schemas for radius. Your path may vary a bit
cp /usr/share/doc/freeradius*/examples/openldap.schema /etc/openldap/schema/radius.schema
2. Create a admin password for slapd. Record this password for later use when configuring the slapd.conf file
slappasswd
3. Add the ldap user and group; if it doesn't exisit. Depending on the install rpm, it may have been created
useradd ldap
groupadd ldap
4. Create the directory and assign permissions for the database files
mkdir /var/lib/ldap
chmod 700 /var/lib/ldap
chown ldap:ldap /var/lib/ldap
5. Edit the slapd.conf file.
cd /etc/openldap
vi slapd.conf
# See slapd.conf(5) for details on configuration options.
# This file should NOT be world readable.
#Default needed schemas
include /etc/openldap/schema/corba.schema
include /etc/openldap/schema/core.schema
include /etc/openldap/schema/cosine.schema
include /etc/openldap/schema/duaconf.schema
include /etc/openldap/schema/dyngroup.schema
include /etc/openldap/schema/inetorgperson.schema
include /etc/openldap/schema/java.schema
include /etc/openldap/schema/misc.schema
include /etc/openldap/schema/nis.schema
include /etc/openldap/schema/openldap.schema
include /etc/openldap/schema/ppolicy.schema
include /etc/openldap/schema/collective.schema
#Radius include
include /etc/openldap/schema/radius.schema
#Samba include
#include /etc/openldap/schema/samba.schema
# Allow LDAPv2 client connections. This is NOT the default.
allow bind_v2
# Do not enable referrals until AFTER you have a working directory
# service AND an understanding of referrals.
#referral ldap://root.openldap.org
pidfile /var/run/openldap/slapd.pid
argsfile /var/run/openldap/slapd.args
# ldbm and/or bdb database definitions
#Use the berkely database
database bdb
#dn suffix, domain components read in order
suffix "dc=cisco,dc=com"
checkpoint 1024 15
#root container node defined
rootdn "cn=Manager,dc=cisco,dc=com"
# Cleartext passwords, especially for the rootdn, should
# be avoided. See slappasswd(8) and slapd.conf(5) for details.
# Use of strong authentication encouraged.
# rootpw secret
rootpw
{SSHA}
cVV/4zKquR4IraFEU7NTG/PIESw8l4JI
# The database directory MUST exist prior to running slapd AND
# should only be accessible by the slapd and slap tools. (chown ldap:ldap)
# Mode 700 recommended.
directory /var/lib/ldap
# Indices to maintain for this database
index objectClass eq,pres
index uid,memberUid eq,pres,sub
# enable monitoring
database monitor
# allow onlu rootdn to read the monitor
access to *
by dn.exact="cn=Manager,dc=cisco,dc=com" read
by * none
6. Remove the slapd.d directory
cd /etc/openldap
rm -rf slapd.d
7. Hopefully if everything is correct, should be able to start up slapd with no problem
service slapd start
8. Create the initial database in a text file called /tmp/initial.ldif
dn: dc=cisco,dc=com
objectClass: dcobject
objectClass: organization
o: cisco
dc: cisco
dn: ou=people,dc=cisco,dc=com
objectClass: organizationalunit
ou: people
description: people
dn: uid=jonatstr,ou=people,dc=cisco,dc=com
objectClass: top
objectClass: radiusprofile
objectClass: inetOrgPerson
cn: jonatstr
sn: jonatstr
uid: jonatstr
description: user Jonathan Strickland
radiusTunnelType: VLAN
radiusTunnelMediumType: 802
radiusTunnelPrivateGroupId: 10
userPassword: ggsg
9. Add the file to the database
ldapadd -h localhost -W -D "cn=Manager, dc=cisco,dc=com" -f /tmp/initial.ldif
10. Issue a basic query to the ldap db, makes sure that we can request and receive results back
ldapsearch -h localhost -W -D cn=Manager,dc=cisco,dc=com -b dc=cisco,dc=com -s sub "objectClass=*"
Configure and Start FreeRadius
1. Configure ldap.attrmap, if needed. This step is only needed if we need to map and pass attributes back to the authenicator (dynamic vlan assignments as an example). Below is an example for dynamic vlan addresses
cd /etc/raddb
vi ldap.attrmap
For dynamic vlan assignments, verify the follow lines exist:
replyItem Tunnel-Type radiusTunnelType
replyItem Tunnel-Medium-Type radiusTunnelMediumType
replyItem Tunnel-Private-Group-Id radiusTunnelPrivateGroupId
Since we are planning to use the userpassword, we will let the mschap module perform the NT translations for us. Add the follow line to check ldap object for userpassword and store as Cleartext-Password:
checkItem Cleartext-Password userPassword
2. Configure eap.conf. The following sections attributes below should be verified. You may change other attributes as needed, they are just not covered in this document.
eap
{ default_eap_type = peap ..... }
tls {
#I will not go into details here as this is beyond scope of setting up freeradisu. The defaults will work, as freeradius comes with generated self signed certificates.
peap {
default_eap_type = mschapv2
#you will have to set this to allowed the inner tls tunnel attributes into the final accept message
use_tunneled_reply = yes
3. Change the authenication and authorization modules and order.
cd /etc/raddb/sites-enabled
vi default
For the authorize section, uncomment the ldap module.
For the authenicate section, uncomment the ldap module
vi inner-tunnel
Very importants, for the authorize section, ensure the ldap module is first, before mschap. Thus authorize will look like:
authorize
{ ldap mschap ...... }
4. Configure ldap module
cd /etc/raddb/modules
ldap
{ server=localhost identify = "cn=Manager,dc=cisco,dc=com" password=admin basedn="dc=cisco,dc=com" base_filter = "(objectclass=radiusprofile)" access_attr="uid" ............ }
5. Start up radius in debug mode on another console
radiusd -X
6. radtest localhost 12 testing123
You should get a Access-Accept back
7. Now to perform an EAP-PEAP test. This will require a wpa_supplicant test libarary called eapol_test
First install openssl support libraries, required to compile
yum install openssl*
yum install gcc
wget http://hostap.epitest.fi/releases/wpa_supplicant-0.6.10.tar.gz
tar xvf wpa_supplicant-0.6.10.tar.gz
cd wpa_supplicant-0.6.10/wpa_supplicant
vi defconfig
Uncomment CONFIG_EAPOL_TEST = y and save/exit
cp defconfig .config
make eapol_test
cp eapol_test /usr/local/bin
chmod 755 /usr/local/bin/eapol_test
8. Create a test config file named eapol_test.conf.peap
network=
{ eap=PEAP eapol_flags=0 key_mgmt=IEEE8021X identity="jonatstr" password="ggsg" \#If you want to verify the Server certificate the below would be needed \#ca_cert="/root/ca.pem" phase2="auth=MSCAHPV2" }
9. Run the test
eapol_test -c ~/eapol_test.conf.peap -a 127.0.0.1 -p 1812 -s testing123 -
Deployment of WLC-5508 with 2702i-D have performance issue.
Hi Team,
We have centrally deployed WLC-5508 with 50 AP licence along with HA scenario. we have 3 locations.
1- HQ. have 26 AP with POWINJ5.
2- Branch location A- 8 AP with POWINJ5.
3. Branch location B have 8 AP with POWINJ4.
my exception is to achieve that single SSID with dynamic VLAN from group police (NPS). MY HO have 26 AP and those are working in local mode.
and branches are connected through flexconnect mode. and all are working with different-2 NPS.
Now i am facing a problem with this deployment are following.
1- branch A have performance issue.
2- HQ have performance issue.
3- i don't want to go with dedicated NPS for every location.
In order to achieve this deployment i want only single SSID with primary and secondary NPS at my HQ with dynamic VLAN for respective departmental users vlans..
above is my problem and concern. otherwise i am successfully achieving this solution with dedicated NPS with single group policy. but when i am going forward to achieve my expectation that time i am facing authentication issue at my HQ and sometimes am not able to get proper VLAN IPs. at my HQ.
kindly help me in that to understand where I am doing wrong things to achieve my expectation.
Thanks.
NalinI am facing 2 different problems.
1st issue- in existing setup we have throughput issue. (while downloading or uploading any data from the internet or Intranet, that time wireless clients are facing slowness of the Speed. and same time when i am trying from LAN i am not facing any issue)
2nd Issue- I want to achieve only single SSID with primary and secondary NPS (AD group is bind with vlan Attributes) with dynamic VLAN for respective departmental users.
for Issue no 2 i have created SSID to achieve the single ssid parameter for every location. in order to achieve i have change all access points mode local to Flexconnect mode after that i have created AP groups location wise and then create flexconnect Groups where i have mapped all the vlan through AAA VLAN-ACL mapping. created interface group and mapped all the vlans in that group.
for more understanding please go through the below mentioned CLI view.
Cisco Controller) >show wlan apgroups
Total Number of AP Groups........................ 4
Site Name........................................ GURGAON-AP-GROUP
Site Description................................. GURGAON-AP-GROUP
Venue Group Code................................. Unspecified
Venue Type Code.................................. Unspecified
NAS-identifier................................... Fractal-WLC1
Client Traffic QinQ Enable....................... FALSE
DHCPv4 QinQ Enable............................... FALSE
AP Operating Class............................... Not-configured
Capwap Prefer Mode............................... Not-configured
RF Profile
2.4 GHz band..................................... <none>
5 GHz band....................................... <none>
WLAN ID Interface Network Admission Control Radio Pol icy
3 gurgaon-interface Disabled None
--More-- or (q)uit
4 gurgaon-guest Disabled None
*AP3600 with 802.11ac Module will only advertise first 8 WLANs on 5GHz radios.
AP Name Slots AP Model Ethernet MAC Location Port Country Priority
GUR-AP-01 2 AIR-CAP2702I-D-K9 f4:4e:05:78:ae:e4 default location 1 IN 1
GUR-AP-05 2 AIR-CAP2702I-D-K9 f4:4e:05:80:b5:18 default location 1 IN 1
GUR-AP-03 2 AIR-CAP2702I-D-K9 bc:16:65:13:71:00 default location 1 IN 1
GUR-AP-07 2 AIR-CAP2702I-D-K9 f4:4e:05:80:b3:f8 default location 1 IN 1
GUR-AP-06 2 AIR-CAP2702I-D-K9 f4:4e:05:80:b3:e0 default location 1 IN 1
GUR-AP-08 2 AIR-CAP2702I-D-K9 f4:4e:05:45:78:98 default location 1 IN 1
GUR-AP-02 2 AIR-CAP2702I-D-K9 f4:4e:05:80:b3:2c default location 1 IN 1
GUR-AP-04 2 AIR-CAP2702I-D-K9 f4:4e:05:78:ae:64 default location 1 IN 1
GUR-AP-09 2 AIR-CAP2702I-D-K9 f4:4e:05:80:b4:44 default location 1 IN 1
Site Name........................................ MUMBAI-AP-GROUP
Site Description................................. MUMBAI-AP-GROUP
Venue Group Code................................. Unspecified
Venue Type Code.................................. Unspecified
--More-- or (q)uit
NAS-identifier................................... Fractal-WLC1
Client Traffic QinQ Enable....................... FALSE
DHCPv4 QinQ Enable............................... FALSE
AP Operating Class............................... Not-configured
Capwap Prefer Mode............................... Not-configured
RF Profile
2.4 GHz band..................................... <none>
5 GHz band....................................... <none>
WLAN ID Interface Network Admission Control Radio Policy
1 group for mumbai Disabled None
2 guest wifi Disabled None
*AP3600 with 802.11ac Module will only advertise first 8 WLANs on 5GHz radios.
AP Name Slots AP Model Ethernet MAC Location Port Country Priority
FAL-7-AP08 2 AIR-CAP2702I-D-K9 f0:7f:06:8d:24:d8 7th Floor 1 IN 3
--More-- or (q)uit
FAL-7-AP10 2 AIR-CAP2702I-D-K9 f0:7f:06:8d:25:18 7th Floor 1 IN 1
FAL-7-AP14 2 AIR-CAP2702I-D-K9 f0:7f:06:bf:ad:e8 7th Floor 1 IN 1
FAL-7-AP01 2 AIR-CAP2702I-D-K9 f0:7f:06:bf:b0:4c 7th Floor 1 IN 1
FAL-7-AP07 2 AIR-CAP2702I-D-K9 f0:7f:06:30:92:bc 7th Floor 1 IN 1
FAL-7-AP13 2 AIR-CAP2702I-D-K9 f0:7f:06:30:91:80 7th Floor 1 IN 1
FAL-7-AP02 2 AIR-CAP2702I-D-K9 f0:7f:06:30:91:94 7th Floor 1 IN 1
FAL-7-AP05 2 AIR-CAP2702I-D-K9 f0:7f:06:30:91:e8 7th Floor 1 IN 1
FAL-7-AP12 2 AIR-CAP2702I-D-K9 f0:7f:06:8d:25:f0 7th Floor 1 IN 3
FAL-7-AP03 2 AIR-CAP2702I-D-K9 f0:7f:06:8d:25:e4 7th Floor 1 IN 1
FAL-7-AP06 2 AIR-CAP2702I-D-K9 f0:7f:06:30:91:84 7th Floor 1 IN 3
FAL-7-AP04 2 AIR-CAP2702I-D-K9 f0:7f:06:bf:b0:14 7th Floor 1 IN 1
FAL-7-AP09 2 AIR-CAP2702I-D-K9 f0:7f:06:92:b4:c8 7th Floor 1 IN 3
FAL-7-AP11 2 AIR-CAP2702I-D-K9 f0:7f:06:30:93:08 7th Floor 1 IN 1
Site Name........................................ MUMBAI-THIRD-FLOOR-AP
Site Description................................. MUMBAI-THIRD-FLOOR-AP
Venue Group Code................................. Unspecified
Venue Type Code.................................. Unspecified
NAS-identifier................................... Fractal-WLC1
Client Traffic QinQ Enable....................... FALSE
--More-- or (q)uit
DHCPv4 QinQ Enable............................... FALSE
AP Operating Class............................... Not-configured
Capwap Prefer Mode............................... Not-configured
RF Profile
2.4 GHz band..................................... <none>
5 GHz band....................................... <none>
WLAN ID Interface Network Admission Control Radio Policy
1 group for mumbai Disabled None
2 guest wifi Disabled None
*AP3600 with 802.11ac Module will only advertise first 8 WLANs on 5GHz radios.
AP Name Slots AP Model Ethernet MAC Location Port Country Priority
FAL-3-AP07 2 AIR-CAP2702I-D-K9 f0:7f:06:30:91:a4 3rd Floor 1 IN 3
FAL-3-AP09 2 AIR-CAP2702I-D-K9 f0:7f:06:8d:25:94 3rd Floor 1 IN 3
FAL-3-AP11 2 AIR-CAP2702I-D-K9 f4:0f:1b:73:00:74 3rd Floor- Eurek 1 IN 3
FAL-3-AP06 2 AIR-CAP2702I-D-K9 f0:7f:06:bf:ae:d0 3rd Floor 1 IN 3
--More-- or (q)uit
FAL-3-AP10 2 AIR-CAP2702I-D-K9 f0:7f:06:92:b5:88 3rd Floor 1 IN 3
FAL-3-AP08 2 AIR-CAP2702I-D-K9 f0:7f:06:92:b4:9c 3rd Floor 1 IN 3
FAL-3-AP03 2 AIR-CAP2702I-D-K9 f0:7f:06:bf:af:a0 3rd Floor 1 IN 1
FAL-3-AP12 2 AIR-CAP2702I-D-K9 f0:7f:06:92:b3:fc 3rd Floor- Eurek 1 IN 3
FAL-3-AP02 2 AIR-CAP2702I-D-K9 f0:7f:06:8d:25:28 3rd Floor 1 IN 3
FAL-3-AP01 2 AIR-CAP2702I-D-K9 f0:7f:06:92:b4:f4 3rd Floor 1 IN 3
FAL-3-AP04 2 AIR-CAP2702I-D-K9 f0:7f:06:30:92:8c 3rd Floor 1 IN 2
FAL-3-AP05 2 AIR-CAP2702I-D-K9 f0:7f:06:30:91:f4 3rd Floor 1 IN 3
Site Name........................................ RAHEJA-AP-GROUP
Site Description................................. RAHEJA-AP-GROUP
Venue Group Code................................. Unspecified
Venue Type Code.................................. Unspecified
NAS-identifier................................... Fractal-WLC1
Client Traffic QinQ Enable....................... FALSE
DHCPv4 QinQ Enable............................... FALSE
AP Operating Class............................... Not-configured
Capwap Prefer Mode............................... Not-configured
RF Profile
--More-- or (q)uit
2.4 GHz band..................................... <none>
5 GHz band....................................... <none>
WLAN ID Interface Network Admission Control Radio Policy
5 raheja-interface Disabled None
2 raheja-guest Disabled None
*AP3600 with 802.11ac Module will only advertise first 8 WLANs on 5GHz radios.
AP Name Slots AP Model Ethernet MAC Location Port Country Priority
FAL-RAHEJA-AP04 2 AIR-CAP2702I-D-K9 f0:7f:06:8d:24:1c Near Meeting Roo 1 IN 3
FAL-RAHEJA-AP02 2 AIR-CAP2702I-D-K9 f0:7f:06:8d:37:3c Confrennce Room 1 IN 3
FAL-RAHEJA-AP03 2 AIR-CAP2702I-D-K9 f0:7f:06:30:93:48 Near Confrence R 1 IN 3
FAL-RAHEJA-AP05 2 AIR-CAP2702I-D-K9 f0:7f:06:bf:ae:c0 Near Meeting Roo 1 IN 3
FAL-RAHEJA-AP06 2 AIR-CAP2702I-D-K9 f0:7f:06:92:b3:a0 Near Server Room 1 IN 3
FAL-RAHEJA-AP01 2 AIR-CAP2702I-D-K9 f0:7f:06:92:b3:20 Reception Area 1 IN 3
FAL-RAHEJA-AP08 2 AIR-CAP2702I-D-K9 f0:7f:06:8d:25:68 USER BAY ROAD si 1 IN 1
FAL-RAHEJA-AP09 2 AIR-CAP2702I-D-K9 f0:7f:06:92:b4:d4 Training Room 1 IN 1
--More-- or (q)uit
Site Name........................................ default-group
Site Description................................. <none>
NAS-identifier................................... Fractal-WLC1
Client Traffic QinQ Enable....................... FALSE
DHCPv4 QinQ Enable............................... FALSE
AP Operating Class............................... Not-configured
Capwap Prefer Mode............................... Not-configured
RF Profile
2.4 GHz band..................................... <none>
5 GHz band....................................... <none>
WLAN ID Interface Network Admission Control Radio Policy
1 group for mumbai Disabled None
2 guest wifi Disabled None
3 gurgaon-interface Disabled None
4 gurgaon-guest Disabled None
5 raheja-interface Disabled None
6 test Disabled None
Cisco Controller) >show flexconnect group summary
FlexConnect Group Summary: Count: 4
Group Name # Aps
Gurgaon-AP 9
HQ-3RD-FLR-AP-GROUP 12
HQ-7THFLR-AP-GROUP 14
Raheja-AP-Group 8
(Cisco Controller) >show flexconnect group detail Gurgaon-AP
Number of AP's in Group: 9
bc:16:65:13:71:00 GUR-AP-03 Joined Flexconnect
f4:4e:05:45:78:98 GUR-AP-08 Joined Flexconnect
f4:4e:05:78:ae:64 GUR-AP-04 Joined Flexconnect
f4:4e:05:78:ae:e4 GUR-AP-01 Joined Flexconnect
f4:4e:05:80:b3:2c GUR-AP-02 Joined Flexconnect
f4:4e:05:80:b3:e0 GUR-AP-06 Joined Flexconnect
f4:4e:05:80:b3:f8 GUR-AP-07 Joined Flexconnect
f4:4e:05:80:b4:44 GUR-AP-09 Joined Flexconnect
f4:4e:05:80:b5:18 GUR-AP-05 Joined Flexconnect
Efficient AP Image Upgrade ..... Disabled
Master-AP-Mac Master-AP-Name Model Manual
Group Radius Servers Settings:
Type Server Address Port
Primary Unconfigured Unconfigured
Secondary Unconfigured Unconfigured
--More-- or (q)uit
Group Radius AP Settings:
AP RADIUS server............ Disabled
EAP-FAST Auth............... Disabled
LEAP Auth................... Disabled
EAP-TLS Auth................ Disabled
EAP-TLS CERT Download....... Disabled
PEAP Auth................... Disabled
Server Key Auto Generated... No
Server Key.................. <hidden>
Authority ID................ 436973636f0000000000000000000000
Authority Info.............. Cisco A_ID
PAC Timeout................. 0
Multicast on Overridden interface config: Disabled
DHCP Broadcast Overridden interface config: Disabled
Number of User's in Group: 0
Vlan :........................................... 203
Ingress ACL :................................... None
Egress ACL :.................................... None
Vlan :........................................... 205
Ingress ACL :................................... None
Egress ACL :.................................... None
Vlan :........................................... 204
--More-- or (q)uit
Ingress ACL :................................... None
Egress ACL :.................................... None
Vlan :........................................... 206
Ingress ACL :................................... None
Egress ACL :.................................... None
Vlan :........................................... 207
Ingress ACL :................................... None
Egress ACL :.................................... None
Vlan :........................................... 208
Ingress ACL :................................... None
Egress ACL :.................................... None
Vlan :........................................... 209
Ingress ACL :................................... None
Egress ACL :.................................... None
Vlan :........................................... 210
Ingress ACL :................................... None
Egress ACL :.................................... None
Vlan :........................................... 211
Ingress ACL :................................... None
Egress ACL :.................................... None
Vlan :........................................... 212
Ingress ACL :................................... None
Egress ACL :.................................... None
--More-- or (q)uit
Vlan :........................................... 216
Ingress ACL :................................... None
Egress ACL :.................................... None
Vlan :........................................... 217
Ingress ACL :................................... None
Egress ACL :.................................... None
Vlan :........................................... 218
Ingress ACL :................................... None
Egress ACL :.................................... None
Group-Specific FlexConnect Wlan-Vlan Mapping:
WLAN ID Vlan ID
WLAN ID SSID Central-Dhcp Dns-Override Nat-Pat
(Cisco Controller) >
(Cisco Controller) >show wlan summary
Number of WLANs.................................. 6
WLAN ID WLAN Profile Name / SSID Status Interface Name PMIPv6 Mobility
1 FRACTAL-EMP-MUMBAI / FRACTAL Enabled group for mumbai none
2 FRACTAL-GUEST / FRACTAL-GUEST Enabled guest wifi none
3 FRACTAL-EMP-GURGAON / FRACTAL-GURGAON Enabled gurgaon-interface none
4 GURGAON-GUEST / FRACTAL-GUEST-GURGAON Enabled gurgaon-guest none
5 RAHEJA-EMP-WIRELESS / FRACTAL-R Enabled raheja-interface none
6 TEST-SSID / TEST-SSID Enabled test none
hope this will give you proper understanding.
Maybe you are looking for
-
CRM 7.0 - Restrict Available BP Roles in Account Maintenance
Dear Experts, During BP Maintenance in CRM 7.0 Web UI, how can we restrict the BP role values that are available in the BP Role assignment block i.e. we want to limit only to "Sold-To Party" and "Contact Person." UI Component: BP_ROLES View: BP_ROLES
-
List view threshold and columns manage metadata problems
Hi We have problem in our company since we have more files in library than is set in List view Threshold. I have created index on column "year" and create view filter: Year is equal 2015. and I get famous error: this view cannot be displayed because.
-
does siri works on ipad 3?
-
Providing a common Connection from 1_WIRE_LO_REF
I am testing the continuity of several cables with DMM 4060 and SCXI 1127 in 1 wire mode. Since i can't connect the wires in the cable at the other end, i'm trying to use a saline solution and insert the cables in it with it's electrode connected to
-
When I installed itunes it went smooth untill quicktime had to install, the error 3 came up and said quciktime couln't be installed. This prevents me from opening itunes. Anyway, I have tried to uninstall my old version of quicktime but the uninstall