WLC-5508 License Moves
Hello,
My network has 26 WLC's. 11 of them are 4402's, the rest are 5508's. 4 of the 5508's are the mobility anchors for the guest traffic. This summer we are removing the 4402's and re-arranging. 6 of the locations will be converted to Meraki. The goal at the end of the summer is to have these locations switched to Meraki and the 5508's consolidated. They will be set up at 4 sites. 1 site just a guest controller. The other 3 will have 3 5508's. 1 for mobility anchor, 1 for the AP's in the sector, 1 as a failover. I have been planning this setup and came upon a question. How do I consolidate the licenses on the 5508's? I have enough from the Meraki locations to comfortably support our AP's, just not per 5508.
Indeed. The only possibilities are 100/100 or 100/0.
100/100 means, it's a 100 ap license and it's activated.
100/0 means that it's a 100 ap liecnse but it's not activated on the WLC.
I don't see a way of only activating half of the AP count of one license (100/50 for example). I don't think that this is possible.
Nicolas
Similar Messages
-
WLC 5508 Base-Ap-Count License Inactive
Hello,
I have two licenses on a WLC 5508 "base-ap-count permenant 100 Count medium Inactive" and "base-ap-count permanent 150 count medium In Use". Should both the 100 and 150 be added up to make 250? Why is the 100 license inactive? There is no option to make it active.Here is my status:
show license summary
License Store: Primary License Storage
StoreIndex: 0 Feature: base-ap-count Version: 1.0
License Type: Permanent
License State: Inactive
License Count: 5 / 0 (Active/In-use)
License Priority: Medium
License Store: Primary License Storage
StoreIndex: 1 Feature: wlc-virtual Version: 1.0
License Type: Permanent
License State: Active, In Use
License Count: 1 /1 (Active/In-use)
License Priority: Medium
License Store: Primary License Storage
StoreIndex: 2 Feature: base-ap-count Version: 1.0
License Type: Permanent
License State: Inactive
License Count: 10 / 0 (Active/In-use)
License Priority: Medium
License Store: Primary License Storage
StoreIndex: 3 Feature: base-ap-count Version: 1.0
License Type: Permanent
License State: Active, In Use
License Count: 15 /15 (Active/In-use)
License Priority: Medium
Both 5 license and 10 license have the dropdown arrow available to delete. Is it ok to delete them?
vWLC came with 5 AP then I added two 5 AP licenses. -
Redundant WLC-5508 Deployment Licensing
I am deploying a redundant WLC-5508. We purchased 2, each with the base license of 50 AP's. After the survey, we determined that we need an additional 9 access points. Do we have to purchase 2 upgrade licenses? If so, can we get them in increments of 5, similar to the 2500 series WLC's?
After the survey, we determined that we need an additional 9 access points. Do we have to purchase 2 upgrade licenses?
Yes. You need to purchase TWO (2) licenses.
Here's the difficulty with your scenario:
For unknown reason, someone in Cisco has determine that, in your case, you have an appliance with 50 bases license and you need to add 9 WAPs. Logic dictates that you could potentially get a 25-base license right? Not in this case. Your minimum license you can get is 100-base license.
Because of this, I would recommend that you raise a TAC Case and potentially get both of the WLC RMA-ed. Tell TAC that you want to get a 25-base license ADDED to both units. (Bringing the total to 75.)
Message was edited by: Leo Laohoo -
Hi,
I don't undestand this document
http://www.cisco.com/c/en/us/td/docs/wireless/technology/hi_avail/N1_High_Availability_Deployment_Guide/N1_HA_Overview.html
How can the third 5508 (suport max 500 AP) backup all other WLC ? n+1 how ?
With secondary wlc configured in HA-SKU (without AP SSO) the 500 licenze are permanent ?
who can explain me.. this is a document bug ??What they're describing is HA N+1, not HA 1:1 AP SSO. This option, which is "NON-AP-SSO", allows you to use an HA-SKU or > -50-k9 SKU coverted, to operate as a dedicated +1 WLC in HA. When using this configuration, this WLC allows the use of the "hardware maximum" of the device: Thus 500 APs for WLC 5508, or 1000APs for a WISM2 (as an example). Since this WLC can wait as a backup to multiple WLCs, that's why it's not capable of the AP SSO, which requires a 1:1 pairing of the HA WLC with an Active HA WLC.
When using the HA N+1 the WLC acts the same as the pre AP-SSO "HA" concept; where you had Primary, Secondary Tertiary configs on your APs (which you may still have). All it is saying is that the N+1 HA WLC can act as one of these Secondary/Tertiary WLCs, much like a WLC you had licenesed for 250 or 500 APs could do previously.
In the past you would use, lets say a 250 WLC AP as this backup WLC. Many people were frustrated that they had to have a $60,000 WLC just sitting there "waiting for something to fail". But that's what it did. If a WLC failed, lets say one with 100 APs, this backup WLC would take on the APs and use 100 of it's 250 AP license count. If additional WLCs failed, the process continued until this backup WLC was filled.
The idea of using the HA-SKU in an N+1 is that while yes, you don't get the 1:1 AP SSO configuration, you are getting more bang for your buck in that this WLC can sit as a backup (as it did in the past) but it can accept up to the maximum it's hardware can handle in terms of AP count, not only what it was permanently licensed for. Rather than spending $100,00 on a 500 AP count WLC to backup your 2x250 AP count WLCs, why not look at a $50,000 HA-SKU that can "handle" up to 500 APs.
So given this scenario, this WLC is "backuping up all other WLCs" for whom it is a Secondary/Tertiary WLC backup.
As far as the HA-SKU "licenese", it's not "permanent" per se. With an HA SKU in N+1 you have a 90 day timer which will then "nag you" (via console) that this HA WLC is not truly intended to permanently house these APs. The idea is that if the Primary WLC failed, you would get it back online and then move your APs back to where they belong and return the HA N+1 WLC back to 0 APs. -
WLC upgrade license and access point
Hi everyone,
I need suggestion regarding wlc 5508 upgrade license. Right now i have 150 license for access points. There will be upgrade around 300 access points. So we are planning to buy new license until the maximum capacity of 5508 (500 licenses).
Our management ip address is 192.168.50.x/24 . so all the access point are pointed to this management ip address (in the same subnet)
First question,
Because there will be an upgrade to around 450 access point. The current management ip address will not be enough.
Please, give me the best suggestion ?
Should i create another management ip address ? or I need to make a bigger subnet using the current management ip address ?
if i create a bigger ip address, the current access points must be set again yups ?
Second question
There will be a new link connected to the wlc, and i want to create new user subnets.
what is the best practices for this matter ?
if there are better suggestion, please let me know, i am still learning about wireless
I have attached the topology.
Thank you
FanieFor an example, a 5508 can support up to 500 AP's, and the AP's can be in one large subnet or be in many different subnets and or even different locations. As long as the ap knows how to discover the WLC or the ap already had joined the WLC, then the AP's don't have to be on the same subnet as the WLC. The easiest way to have AP's join is to stage them on the same subnet as the WLC management and then move them to a different subnet. I would probably have no more than 100 AP's per subnet, but that's me. Stage some AP's on the management subnet that the WLC is on and then when the AP's join and complete downloading code, change the switch port Vlan and shut and no shut the port. The ap will come back up and join the WLC.
Sent from Cisco Technical Support iPhone App -
Converged Access Design Help (Catalyst 3850 and WLC 5508...Mobility Oracle)
Hello,
I am an engineer working with a Cisco Gold Partner in Saudi Arabia. We have a large university as our client where they are constructing a new
building and require our services to build the network infrastructure. Therefore, we are to implement the routing and switching infrastructure as
well as the Wireless solution.
At present, I have no issues in implementing the R&S infrastructure as it is very straight forward but it has implications on the deployment of
the wireless solution which I explain further below. The R&S infrastructure comprises of the typical Core, Distribution, and Access layers and we
are focusing on the local distribution and access switches with regards to the new building. The client has a converged Layer 3 network spanning
from distribution layer to core layer and they are running EIGRP for this convergence. This is not a problem and has already been implemented.
Yet, the challenge arises in deploying the WLAN infrastructure. The client already has a Cisco WLAN infrastructure in place where they have a
large number of LAPs that are registered with their controllers in the Data Center. They have two WLC 5508 where one is the Primary and the other
the Secondary. The local distribution switch to which the WLC are connected also is the gateway for the SVIs for the SSIDs that are configured on
the controllers. This means that once the packets from the AP come in to the WLC, they are tagged with the correct VLAN and sent to the directly
connected distribution switch which then routes it into the rest of the Layer 3 network. Interestingly, the WLC 5508 are running AireOS 7.6 and
support the "New Mobility" feature. The two controllers have formed a Mobility Group (MG) between each other.
Now, the new building will have two Catalyst 3850 switches installed where each one has a total of 40 AP licenses pre-installed and activated
i.e. a total of 80 APs can be supported by the two switches. A total of 67 LAPs will be deployed in the new building which can be accommodated
between the two switches and their integrated controller.
Yet, based on my understanding and research about Converged Access is that, ideally, the Catalyst 3850 will only run the Mobility Agent (MA)
feature while a central controller would provide the Mobility Controller (MC) service. unfortunately, there are not enough licenses on the
existing WLC 5508 nor can we migrate the new licenses that will facilitate such a split deployment.
This means that I would need to configure the two Catalyst 3850 as independent MC and form a MG between them. I have done this and tested this
already and the mobility is working fine. But my concern is not about getting the Catalyst 3850 to work as this is simple but rather it is
focused on creating a common Mobility Domain (MD) so that clients can roam from this new building to the rest of the campus while maintaining the
state of their connections to the WLAN infrastructure.
To make things more complicated, since the new building will have its own Layer 3 distribution switch and the Catalyst 3850 switches will connect
to this distribution switch, it means that new VLANs and SVIs need to be created for the SSIDs broadcast in the new building. This means that new
subnets need to be assigned to the SSIDs.
As such, I have the following questions:
Q1) If we create new SVIs for the SSIDs (same SSIDs names will be used in the new building as in the rest of the university campus) this means
that new subnets will be assigned to these SSIDs. Now, I believe I have two options...one is to make the new Catalyst 3850s to be in the same MG
as the existing WLC 5508 which then cater for Layer 3 client roaming or I have to treat this as a totally seperate WLAN network and follow on to
the solution as per the next question. Please advise which is a better option?
Q2) I could create separate MG i.e. the new building Catalyst 3850s can be in one MG and the existing controllers can be in another MG. I can
then have one of the existing WLC 5508 (the primary one) to run the Mobility Oracle (MO) feature so as to create a single Mobility Domain (MD).
Would this facilitate in Layer 3 client roaming and RRM for all the controllers in the same MD?
Q3) If I do create a MD, how is this accomplished in such an environment since the documentation is severely limited in this regard?
Please advise at your earliest. To assist further, I have attached a topology diagram which may aid in explaining the situation with more
clarity. If these things are clarified, I will be better able to wrap my head around the technology and in turn service my clients better.
Regards,
AmirHi Amir,
Q1) If we create new SVIs for the SSIDs (same SSIDs names will be used in the new building as in the rest of the university campus) this means that new subnets will be assigned to these SSIDs. Now, I believe I have two options...one is to make the new Catalyst 3850s to be in the same MG as the existing WLC 5508 which then cater for Layer 3 client roaming or I have to treat this as a totally seperate WLAN network and follow on to the solution as per the next question. Please advise which is a better option?
I would configure them in the same mobility group. Also configure same SPG for those two 3850 stacks if users are frequently roaming within these two buildings.
Q2) I could create separate MG i.e. the new building Catalyst 3850s can be in one MG and the existing controllers can be in another MG. I can then have one of the existing WLC 5508 (the primary one) to run the Mobility Oracle (MO) feature so as to create a single Mobility Domain (MD). Would this facilitate in Layer 3 client roaming and RRM for all the controllers in the same MD?
MO is not required (it is only for very large scale deployments)
Q3) If I do create a MD, how is this accomplished in such an environment since the documentation is severely limited in this regard?
Yes, documents are hard to find :(
These notes may be useful to you based on my experience. I am running IOS-XE 3.6.1 in my production.
http://mrncciew.com/2014/05/06/configuring-new-mobility/
http://mrncciew.com/2013/12/14/3850ma-with-5760mc/
HTH
Rasika
*** Pls rate all useful responses **** -
Cisco ISE 1.2 & Cisco WLC 5508 v7.6
Hi all,
we are planning to upgrade our WLC to 7.6 to fix a bug with FlexConnect Client ACLs but I have just seen on the Cisco ISE Compatibility table that the it only recommends up to v7.5 of the WLC 5508...
Cisco have told me to steer clear of 7.5 as it is in a defferred status, so does anyone know, or have running in a lab or production, ISE1.2 with a 5508 WLC v7.6 NAD ?
I would much rather know of any issues people are experiencing before hand than to have to go through a software upgrade and then rollback.
Thanks all
Mario De RosaHi Neno,
right I have this almost working now.
I have simplified the setup. I am not going to do any client provisioning at the moment.
So I can connect to the corporate SSID using EAP-TLS and I can successfully push the branch data VLAN upon successful authorisation.
Now I am trying to introduce the posture element & per user ACLs.
I have defined the redirect ACL & Flex ACL on the vWLC however the NAC agent will not pop-up. The client is in the right VLAN and the redirect ACL seems to be getting applied as the client does get an IP through DHCP. However, the client cannot ping the ISE or access the guest portal when I open the browser.
DNS resolution seems to be working fine.
VLAN220 is my datacentre VLAN which the Management Interface on the controller is plugged in to.
VLAN10 is the branch DATA VLAN.
below is some output to give you some more details...
(Cisco Controller) >show client detail 00:24:d6:97:b3:be
Client MAC Address............................... 00:24:d6:97:b3:be
Client Username ................................. [email protected]
AP MAC Address................................... 18:33:9d:f0:21:80
AP Name.......................................... test-flex-ap
AP radio slot Id................................. 0
Client State..................................... Associated
Client NAC OOB State............................. Access
Wireless LAN Id.................................. 2
Hotspot (802.11u)................................ Not Supported
BSSID............................................ 18:33:9d:f0:21:81
Connected For ................................... 128 secs
Channel.......................................... 6
IP Address....................................... 10.130.130.120
Gateway Address.................................. 10.130.130.1
Netmask.......................................... 255.255.255.0
IPv6 Address..................................... fe80::f524:1910:69f0:9482
Association Id................................... 1
Authentication Algorithm......................... Open System
Reason Code...................................... 1
Status Code...................................... 0
Client CCX version............................... 4
Client E2E version............................... 1
--More-- or (q)uit
Re-Authentication Timeout........................ 1651
QoS Level........................................ Silver
Avg data Rate.................................... 0
Burst data Rate.................................. 0
Avg Real time data Rate.......................... 0
Burst Real Time data Rate........................ 0
802.1P Priority Tag.............................. disabled
CTS Security Group Tag........................... Not Applicable
KTS CAC Capability............................... No
WMM Support...................................... Enabled
APSD ACs....................................... BK BE VI VO
Power Save....................................... OFF
Current Rate..................................... m13
Supported Rates.................................. 1.0,2.0,5.5,11.0,6.0,9.0,
............................................. 12.0,18.0,24.0,36.0,48.0,
............................................. 54.0
Mobility State................................... Local
Mobility Move Count.............................. 0
Security Policy Completed........................ No
Policy Manager State............................. POSTURE_REQD
Policy Manager Rule Created...................... Yes
AAA Override ACL Name............................ POSTURE_REDIRECT_ACL
AAA Override ACL Applied Status.................. Yes
--More-- or (q)uit
AAA Override Flex ACL Name....................... POSTURE_REDIRECT_ACL
AAA Override Flex ACL Applied Status............. Yes
AAA URL redirect................................. https://pdc-ise-man01.kier.group:8443/guestportal/gateway?sessionId=c8dc800a00000005b3e7e953&action=cpp
Audit Session ID................................. c8dc800a00000005b3e7e953
AAA Role Type.................................... none
Local Policy Applied............................. none
IPv4 ACL Name.................................... none
FlexConnect ACL Applied Status................... Yes
IPv4 ACL Applied Status.......................... Unavailable
IPv6 ACL Name.................................... none
IPv6 ACL Applied Status.......................... Unavailable
Layer2 ACL Name.................................. none
Layer2 ACL Applied Status........................ Unavailable
mDNS Status...................................... Disabled
mDNS Profile Name................................ none
No. of mDNS Services Advertised.................. 0
Policy Type...................................... WPA2
Authentication Key Management.................... 802.1x
Encryption Cipher................................ CCMP (AES)
Protected Management Frame ...................... No
Management Frame Protection...................... No
EAP Type......................................... EAP-TLS
FlexConnect Data Switching....................... Local
--More-- or (q)uit
FlexConnect Dhcp Status.......................... Local
FlexConnect Vlan Based Central Switching......... No
FlexConnect Authentication....................... Central
Quarantine VLAN.................................. 0
Access VLAN...................................... 220
Client Capabilities:
CF Pollable................................ Not implemented
CF Poll Request............................ Not implemented
Short Preamble............................. Implemented
PBCC....................................... Not implemented
Channel Agility............................ Not implemented
Listen Interval............................ 10
Fast BSS Transition........................ Not implemented
Client Wifi Direct Capabilities:
WFD capable................................ No
Manged WFD capable......................... No
Cross Connection Capable................... No
Support Concurrent Operation............... No
Fast BSS Transition Details:
Client Statistics:
Number of Bytes Received................... 33698
Number of Bytes Sent....................... 19397
Total Number of Bytes Sent................. 19397
--More-- or (q)uit
Total Number of Bytes Recv................. 33698
Number of Bytes Sent (last 90s)............ 19397
Number of Bytes Recv (last 90s)............ 33698
Number of Packets Received................. 283
Number of Packets Sent..................... 147
Number of Interim-Update Sent.............. 0
Number of EAP Id Request Msg Timeouts...... 0
Number of EAP Id Request Msg Failures...... 0
Number of EAP Request Msg Timeouts......... 0
Number of EAP Request Msg Failures......... 0
Number of EAP Key Msg Timeouts............. 0
Number of EAP Key Msg Failures............. 0
Number of Data Retries..................... 53
Number of RTS Retries...................... 0
Number of Duplicate Received Packets....... 2
Number of Decrypt Failed Packets........... 0
Number of Mic Failured Packets............. 0
Number of Mic Missing Packets.............. 0
Number of RA Packets Dropped............... 0
Number of Policy Errors.................... 0
Radio Signal Strength Indicator............ -42 dBm
Signal to Noise Ratio...................... 41 dB
Client Rate Limiting Statistics:
--More-- or (q)uit
Number of Data Packets Recieved............ 0
Number of Data Rx Packets Dropped.......... 0
Number of Data Bytes Recieved.............. 0
Number of Data Rx Bytes Dropped............ 0
Number of Realtime Packets Recieved........ 0
Number of Realtime Rx Packets Dropped...... 0
Number of Realtime Bytes Recieved.......... 0
Number of Realtime Rx Bytes Dropped........ 0
Number of Data Packets Sent................ 0
Number of Data Tx Packets Dropped.......... 0
Number of Data Bytes Sent.................. 0
Number of Data Tx Bytes Dropped............ 0
Number of Realtime Packets Sent............ 0
Number of Realtime Tx Packets Dropped...... 0
Number of Realtime Bytes Sent.............. 0
Number of Realtime Tx Bytes Dropped........ 0
Nearby AP Statistics:
test-flex-ap(slot 0)
antenna0: 14 secs ago.................... -51 dBm
antenna1: 14 secs ago.................... -37 dBm
test-flex-ap(slot 1)
antenna0: 14 secs ago.................... -51 dBm
antenna1: 14 secs ago.................... -54 dBm
--More-- or (q)uit
DNS Server details:
DNS server IP ............................. 10.0.17.31
DNS server IP ............................. 10.0.17.43
Assisted Roaming Prediction List details:
Client Dhcp Required: False
Allowed (URL)IP Addresses
(Cisco Controller) >
(Cisco Controller) >show wlan 2
WLAN Identifier.................................. 2
Profile Name..................................... Demo1x
Network Name (SSID).............................. Demo1x
Status........................................... Enabled
MAC Filtering.................................... Disabled
Broadcast SSID................................... Enabled
AAA Policy Override.............................. Enabled
Network Admission Control
Client Profiling Status
Radius Profiling ............................ Disabled
DHCP ....................................... Disabled
HTTP ....................................... Disabled
Local Profiling ............................. Disabled
DHCP ....................................... Disabled
HTTP ....................................... Disabled
Radius-NAC State............................... Enabled
SNMP-NAC State................................. Disabled
Quarantine VLAN................................ 0
Maximum number of Associated Clients............. 0
Maximum number of Clients per AP Radio........... 200
--More-- or (q)uit
Number of Active Clients......................... 1
Exclusionlist Timeout............................ 60 seconds
Session Timeout.................................. 1800 seconds
User Idle Timeout................................ Disabled
Sleep Client..................................... disable
Sleep Client Timeout............................. 12 hours
User Idle Threshold.............................. 0 Bytes
NAS-identifier................................... mario-test-flex-vwlc
CHD per WLAN..................................... Enabled
Webauth DHCP exclusion........................... Disabled
Interface........................................ management
Multicast Interface.............................. Not Configured
WLAN IPv4 ACL.................................... unconfigured
WLAN IPv6 ACL.................................... unconfigured
WLAN Layer2 ACL.................................. unconfigured
mDNS Status...................................... Disabled
mDNS Profile Name................................ unconfigured
DHCP Server...................................... Default
DHCP Address Assignment Required................. Disabled
Static IP client tunneling....................... Disabled
Quality of Service............................... Silver
Per-SSID Rate Limits............................. Upstream Downstream
Average Data Rate................................ 0 0
--More-- or (q)uit
Average Realtime Data Rate....................... 0 0
Burst Data Rate.................................. 0 0
Burst Realtime Data Rate......................... 0 0
Per-Client Rate Limits........................... Upstream Downstream
Average Data Rate................................ 0 0
Average Realtime Data Rate....................... 0 0
Burst Data Rate.................................. 0 0
Burst Realtime Data Rate......................... 0 0
Scan Defer Priority.............................. 4,5,6
Scan Defer Time.................................. 100 milliseconds
WMM.............................................. Allowed
WMM UAPSD Compliant Client Support............... Disabled
Media Stream Multicast-direct.................... Disabled
CCX - AironetIe Support.......................... Enabled
CCX - Gratuitous ProbeResponse (GPR)............. Disabled
CCX - Diagnostics Channel Capability............. Disabled
Dot11-Phone Mode (7920).......................... Disabled
Wired Protocol................................... None
Passive Client Feature........................... Disabled
Peer-to-Peer Blocking Action..................... Disabled
Radio Policy..................................... All
DTIM period for 802.11a radio.................... 1
DTIM period for 802.11b radio.................... 1
--More-- or (q)uit
Radius Servers
Authentication................................ 10.0.16.111 1812
Accounting.................................... 10.131.16.111 1813
Interim Update............................. Disabled
Framed IPv6 Acct AVP ...................... Prefix
Dynamic Interface............................. Disabled
Dynamic Interface Priority.................... wlan
Local EAP Authentication......................... Disabled
Security
802.11 Authentication:........................ Open System
FT Support.................................... Disabled
Static WEP Keys............................... Disabled
802.1X........................................ Disabled
Wi-Fi Protected Access (WPA/WPA2)............. Enabled
WPA (SSN IE)............................... Disabled
WPA2 (RSN IE).............................. Enabled
TKIP Cipher............................. Disabled
AES Cipher.............................. Enabled
Auth Key Management
802.1x.................................. Enabled
PSK..................................... Disabled
CCKM.................................... Disabled
--More-- or (q)uit
FT-1X(802.11r).......................... Disabled
FT-PSK(802.11r)......................... Disabled
PMF-1X(802.11w)......................... Disabled
PMF-PSK(802.11w)........................ Disabled
FT Reassociation Timeout................... 20
FT Over-The-DS mode........................ Enabled
GTK Randomization.......................... Disabled
SKC Cache Support.......................... Disabled
CCKM TSF Tolerance......................... 1000
WAPI.......................................... Disabled
Wi-Fi Direct policy configured................ Disabled
EAP-Passthrough............................... Disabled
CKIP ......................................... Disabled
Web Based Authentication...................... Disabled
Web-Passthrough............................... Disabled
Conditional Web Redirect...................... Disabled
Splash-Page Web Redirect...................... Disabled
Auto Anchor................................... Disabled
FlexConnect Local Switching................... Enabled
flexconnect Central Dhcp Flag................. Disabled
flexconnect nat-pat Flag...................... Disabled
flexconnect Dns Override Flag................. Disabled
flexconnect PPPoE pass-through................ Disabled
--More-- or (q)uit
flexconnect local-switching IP-source-guar.... Disabled
FlexConnect Vlan based Central Switching ..... Disabled
FlexConnect Local Authentication.............. Disabled
FlexConnect Learn IP Address.................. Enabled
Client MFP.................................... Optional
PMF........................................... Disabled
PMF Association Comeback Time................. 1
PMF SA Query RetryTimeout..................... 200
Tkip MIC Countermeasure Hold-down Timer....... 60
Eap-params.................................... Disabled
AVC Visibilty.................................... Disabled
AVC Profile Name................................. None
Flow Monitor Name................................ None
Split Tunnel (Printers).......................... Disabled
Call Snooping.................................... Disabled
Roamed Call Re-Anchor Policy..................... Disabled
SIP CAC Fail Send-486-Busy Policy................ Disabled
SIP CAC Fail Send Dis-Association Policy......... Disabled
KTS based CAC Policy............................. Disabled
Assisted Roaming Prediction Optimization......... Disabled
802.11k Neighbor List............................ Disabled
802.11k Neighbor List Dual Band.................. Disabled
Band Select...................................... Disabled
--More-- or (q)uit
Load Balancing................................... Disabled
Multicast Buffer................................. Disabled
Mobility Anchor List
WLAN ID IP Address Status
802.11u........................................ Disabled
MSAP Services.................................. Disabled
Local Policy
Priority Policy Name
(Cisco Controller) >
when debugging the client during redirect, this is the output and I cannot spot anything wrong here...
(Cisco Controller) >*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Adding mobile on LWAPP AP 18:33:9d:f0:21:80(1)
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Association received from mobile on BSSID 18:33:9d:f0:21:8e
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Global 200 Clients are allowed to AP radio
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Max Client Trap Threshold: 0 cur: 0
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Rf profile 600 Clients are allowed to AP wlan
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be override for default ap group, marking intgrp NULL
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Applying Interface policy on Mobile, role Unassociated. Ms NAC State 0 Quarantine Vlan 0 Access Vlan 0
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Re-applying interface policy for client
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be 0.0.0.0 START (0) Changing IPv4 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2219)
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be 0.0.0.0 START (0) Changing IPv6 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2240)
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be apfApplyWlanPolicy: Retaining the ACL recieved in AAA attributes 255 on mobile
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be apfApplyWlanPolicy: Apply WLAN Policy over PMIPv6 Client Mobility Type
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be In processSsidIE:4850 setting Central switched to FALSE
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Applying site-specific Local Bridging override for station 00:24:d6:97:b3:be - vapId 2, site 'default-group', interface 'management'
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Applying Local Bridging Interface Policy for station 00:24:d6:97:b3:be - vlan 220, interface id 0, interface 'management'
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be processSsidIE statusCode is 0 and status is 0
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be processSsidIE ssid_done_flag is 0 finish_flag is 0
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be STA - rates (8): 140 18 152 36 176 72 96 108 0 0 0 0 0 0 0 0
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be suppRates statusCode is 0 and gotSuppRatesElement is 1
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Processing RSN IE type 48, length 22 for mobile 00:24:d6:97:b3:be
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Received RSN IE with 0 PMKIDs from mobile 00:24:d6:97:b3:be
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Setting active key cache index 8 ---> 8
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be unsetting PmkIdValidatedByAp
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Updating AID for REAP AP Client 18:33:9d:f0:21:80 - AID ===> 1
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be 0.0.0.0 START (0) Initializing policy
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be 0.0.0.0 START (0) Change state to AUTHCHECK (2) last state START (0)
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be 0.0.0.0 AUTHCHECK (2) Change state to 8021X_REQD (3) last state AUTHCHECK (2)
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Central switch is FALSE
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be 0.0.0.0 8021X_REQD (3) DHCP required on AP 18:33:9d:f0:21:80 vapId 2 apVapId 2for this client
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Not Using WMM Compliance code qosCap 00
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be 0.0.0.0 8021X_REQD (3) Plumbed mobile LWAPP rule on AP 18:33:9d:f0:21:80 vapId 2 apVapId 2 flex-acl-name:
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be apfMsAssoStateInc
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be apfPemAddUser2 (apf_policy.c:333) Changing state for mobile 00:24:d6:97:b3:be on AP 18:33:9d:f0:21:80 from Idle to Associated
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be apfPemAddUser2:session timeout forstation 00:24:d6:97:b3:be - Session Tout 0, apfMsTimeOut '0' and sessionTimerRunning flag is 0
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Stopping deletion of Mobile Station: (callerId: 48)
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Func: apfPemAddUser2, Ms Timeout = 0, Session Timeout = 0
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Sending Assoc Response to station on BSSID 18:33:9d:f0:21:8e (status 0) ApVapId 2 Slot 1
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be apfProcessAssocReq (apf_80211.c:8294) Changing state for mobile 00:24:d6:97:b3:be on AP 18:33:9d:f0:21:80 from Associated to Associated
*spamApTask6: Aug 12 10:58:24.016: 00:24:d6:97:b3:be Sent 1x initiate message to multi thread task for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.016: 00:24:d6:97:b3:be EAP-PARAM Debug - eap-params for Wlan-Id :2 is disabled - applying Global eap timers and retries
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.016: 00:24:d6:97:b3:be Station 00:24:d6:97:b3:be setting dot1x reauth timeout = 1800
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.016: 00:24:d6:97:b3:be dot1x - moving mobile 00:24:d6:97:b3:be into Connecting state
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.016: 00:24:d6:97:b3:be Sending EAP-Request/Identity to mobile 00:24:d6:97:b3:be (EAP Id 1)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.016: 00:24:d6:97:b3:be mscb->apfMsLwappLradNhMac = 00:00:0c:07:ac:dc mscb->apfMsLradSlotId = 1 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.016: 00:24:d6:97:b3:be mscb->apfMsBssid = 18:33:9d:f0:21:80 mscb->apfMsAddress = 00:24:d6:97:b3:be mscb->apfMsApVapId = 2
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.016: 00:24:d6:97:b3:be dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 220 mscb->apfMsLwappMwarInet.ipv4.addr = 176217288
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.016: 00:24:d6:97:b3:be mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = 176325157 mscb->apfMsLwappLradPort = 9385
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.083: 00:24:d6:97:b3:be Received EAPOL EAPPKT from mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.083: 00:24:d6:97:b3:be Received Identity Response (count=1) from mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.083: 00:24:d6:97:b3:be Resetting reauth count 1 to 0 for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.083: 00:24:d6:97:b3:be EAP State update from Connecting to Authenticating for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.083: 00:24:d6:97:b3:be dot1x - moving mobile 00:24:d6:97:b3:be into Authenticating state
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.083: 00:24:d6:97:b3:be Entering Backend Auth Response state for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.086: 00:24:d6:97:b3:be Processing Access-Challenge for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.086: 00:24:d6:97:b3:be Entering Backend Auth Req state (id=214) for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.086: 00:24:d6:97:b3:be WARNING: updated EAP-Identifier 1 ===> 214 for STA 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.086: 00:24:d6:97:b3:be Sending EAP Request from AAA to mobile 00:24:d6:97:b3:be (EAP Id 214)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.086: 00:24:d6:97:b3:be Allocating EAP Pkt for retransmission to mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.086: 00:24:d6:97:b3:be mscb->apfMsLwappLradNhMac = 00:00:0c:07:ac:dc mscb->apfMsLradSlotId = 1 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.086: 00:24:d6:97:b3:be mscb->apfMsBssid = 18:33:9d:f0:21:80 mscb->apfMsAddress = 00:24:d6:97:b3:be mscb->apfMsApVapId = 2
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.086: 00:24:d6:97:b3:be dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 220 mscb->apfMsLwappMwarInet.ipv4.addr = 176217288
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.086: 00:24:d6:97:b3:be mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = 176325157 mscb->apfMsLwappLradPort = 9385
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.090: 00:24:d6:97:b3:be Received EAPOL EAPPKT from mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.090: 00:24:d6:97:b3:be Received EAP Response from mobile 00:24:d6:97:b3:be (EAP Id 214, EAP Type 13)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.090: 00:24:d6:97:b3:be Resetting reauth count 0 to 0 for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.090: 00:24:d6:97:b3:be Entering Backend Auth Response state for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.091: 00:24:d6:97:b3:be Processing Access-Challenge for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.091: 00:24:d6:97:b3:be Entering Backend Auth Req state (id=215) for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.091: 00:24:d6:97:b3:be Sending EAP Request from AAA to mobile 00:24:d6:97:b3:be (EAP Id 215)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.091: 00:24:d6:97:b3:be Reusing allocated memory for EAP Pkt for retransmission to mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.091: 00:24:d6:97:b3:be mscb->apfMsLwappLradNhMac = 00:00:0c:07:ac:dc mscb->apfMsLradSlotId = 1 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.091: 00:24:d6:97:b3:be mscb->apfMsBssid = 18:33:9d:f0:21:80 mscb->apfMsAddress = 00:24:d6:97:b3:be mscb->apfMsApVapId = 2
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.091: 00:24:d6:97:b3:be dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 220 mscb->apfMsLwappMwarInet.ipv4.addr = 176217288
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.091: 00:24:d6:97:b3:be mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = 176325157 mscb->apfMsLwappLradPort = 9385
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.095: 00:24:d6:97:b3:be Received EAPOL EAPPKT from mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.095: 00:24:d6:97:b3:be Received EAP Response from mobile 00:24:d6:97:b3:be (EAP Id 215, EAP Type 13)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.095: 00:24:d6:97:b3:be Resetting reauth count 0 to 0 for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.095: 00:24:d6:97:b3:be Entering Backend Auth Response state for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.096: 00:24:d6:97:b3:be Processing Access-Challenge for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.096: 00:24:d6:97:b3:be Entering Backend Auth Req state (id=216) for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.096: 00:24:d6:97:b3:be Sending EAP Request from AAA to mobile 00:24:d6:97:b3:be (EAP Id 216)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.096: 00:24:d6:97:b3:be Reusing allocated memory for EAP Pkt for retransmission to mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.096: 00:24:d6:97:b3:be mscb->apfMsLwappLradNhMac = 00:00:0c:07:ac:dc mscb->apfMsLradSlotId = 1 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.096: 00:24:d6:97:b3:be mscb->apfMsBssid = 18:33:9d:f0:21:80 mscb->apfMsAddress = 00:24:d6:97:b3:be mscb->apfMsApVapId = 2
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.096: 00:24:d6:97:b3:be dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 220 mscb->apfMsLwappMwarInet.ipv4.addr = 176217288
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.096: 00:24:d6:97:b3:be mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = 176325157 mscb->apfMsLwappLradPort = 9385
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.100: 00:24:d6:97:b3:be Received EAPOL EAPPKT from mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.100: 00:24:d6:97:b3:be Received EAP Response from mobile 00:24:d6:97:b3:be (EAP Id 216, EAP Type 13)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.100: 00:24:d6:97:b3:be Resetting reauth count 0 to 0 for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.100: 00:24:d6:97:b3:be Entering Backend Auth Response state for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.101: 00:24:d6:97:b3:be Processing Access-Challenge for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.101: 00:24:d6:97:b3:be Entering Backend Auth Req state (id=217) for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.101: 00:24:d6:97:b3:be Sending EAP Request from AAA to mobile 00:24:d6:97:b3:be (EAP Id 217)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.101: 00:24:d6:97:b3:be Reusing allocated memory for EAP Pkt for retransmission to mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.101: 00:24:d6:97:b3:be mscb->apfMsLwappLradNhMac = 00:00:0c:07:ac:dc mscb->apfMsLradSlotId = 1 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.101: 00:24:d6:97:b3:be mscb->apfMsBssid = 18:33:9d:f0:21:80 mscb->apfMsAddress = 00:24:d6:97:b3:be mscb->apfMsApVapId = 2
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.101: 00:24:d6:97:b3:be dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 220 mscb->apfMsLwappMwarInet.ipv4.addr = 176217288
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.101: 00:24:d6:97:b3:be mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = 176325157 mscb->apfMsLwappLradPort = 9385
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.105: 00:24:d6:97:b3:be Received EAPOL EAPPKT from mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.105: 00:24:d6:97:b3:be Received EAP Response from mobile 00:24:d6:97:b3:be (EAP Id 217, EAP Type 13)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.105: 00:24:d6:97:b3:be Resetting reauth count 0 to 0 for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.105: 00:24:d6:97:b3:be Entering Backend Auth Response state for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.106: 00:24:d6:97:b3:be Processing Access-Challenge for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.106: 00:24:d6:97:b3:be Entering Backend Auth Req state (id=218) for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.106: 00:24:d6:97:b3:be Sending EAP Request from AAA to mobile 00:24:d6:97:b3:be (EAP Id 218)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.106: 00:24:d6:97:b3:be Reusing allocated memory for EAP Pkt for retransmission to mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.106: 00:24:d6:97:b3:be mscb->apfMsLwappLradNhMac = 00:00:0c:07:ac:dc mscb->apfMsLradSlotId = 1 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.106: 00:24:d6:97:b3:be mscb->apfMsBssid = 18:33:9d:f0:21:80 mscb->apfMsAddress = 00:24:d6:97:b3:be mscb->apfMsApVapId = 2
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.106: 00:24:d6:97:b3:be dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 220 mscb->apfMsLwappMwarInet.ipv4.addr = 176217288
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.106: 00:24:d6:97:b3:be mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = 176325157 mscb->apfMsLwappLradPort = 9385
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.110: 00:24:d6:97:b3:be Received EAPOL EAPPKT from mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.110: 00:24:d6:97:b3:be Received EAP Response from mobile 00:24:d6:97:b3:be (EAP Id 218, EAP Type 13)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.110: 00:24:d6:97:b3:be Resetting reauth count 0 to 0 for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.110: 00:24:d6:97:b3:be Entering Backend Auth Response state for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.111: 00:24:d6:97:b3:be Processing Access-Challenge for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.111: 00:24:d6:97:b3:be Entering Backend Auth Req state (id=219) for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.111: 00:24:d6:97:b3:be Sending EAP Request from AAA to mobile 00:24:d6:97:b3:be (EAP Id 219)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.111: 00:24:d6:97:b3:be Reusing allocated memory for EAP Pkt for retransmission to mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.111: 00:24:d6:97:b3:be mscb->apfMsLwappLradNhMac = 00:00:0c:07:ac:dc mscb->apfMsLradSlotId = 1 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.111: 00:24:d6:97:b3:be mscb->apfMsBssid = 18:33:9d:f0:21:80 mscb->apfMsAddress = 00:24:d6:97:b3:be mscb->apfMsApVapId = 2
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.111: 00:24:d6:97:b3:be dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 220 mscb->apfMsLwappMwarInet.ipv4.addr = 176217288
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.111: 00:24:d6:97:b3:be mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = 176325157 mscb->apfMsLwappLradPort = 9385
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.115: 00:24:d6:97:b3:be Received EAPOL EAPPKT from mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.115: 00:24:d6:97:b3:be Received EAP Response from mobile 00:24:d6:97:b3:be (EAP Id 219, EAP Type 13)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.115: 00:24:d6:97:b3:be Resetting reauth count 0 to 0 for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.115: 00:24:d6:97:b3:be Entering Backend Auth Response state for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.116: 00:24:d6:97:b3:be Processing Access-Challenge for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.116: 00:24:d6:97:b3:be Entering Backend Auth Req state (id=220) for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.116: 00:24:d6:97:b3:be Sending EAP Request from AAA to mobile 00:24:d6:97:b3:be (EAP Id 220)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.116: 00:24:d6:97:b3:be Reusing allocated memory for EAP Pkt for retransmission to mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.116: 00:24:d6:97:b3:be mscb->apfMsLwappLradNhMac = 00:00:0c:07:ac:dc mscb->apfMsLradSlotId = 1 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.116: 00:24:d6:97:b3:be mscb->apfMsBssid = 18:33:9d:f0:21:80 mscb->apfMsAddress = 00:24:d6:97:b3:be mscb->apfMsApVapId = 2
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.116: 00:24:d6:97:b3:be dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 220 mscb->apfMsLwappMwarInet.ipv4.addr = 176217288
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.116: 00:24:d6:97:b3:be mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = 176325157 mscb->apfMsLwappLradPort = 9385
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.352: 00:24:d6:97:b3:be Received EAPOL EAPPKT from mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.352: 00:24:d6:97:b3:be Received EAP Response from mobile 00:24:d6:97:b3:be (EAP Id 220, EAP Type 13)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.352: 00:24:d6:97:b3:be Resetting reauth count 0 to 0 for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.352: 00:24:d6:97:b3:be Entering Backend Auth Response state for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.354: 00:24:d6:97:b3:be Processing Access-Challenge for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.354: 00:24:d6:97:b3:be Entering Backend Auth Req state (id=221) for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.354: 00:24:d6:97:b3:be Sending EAP Request from AAA to mobile 00:24:d6:97:b3:be (EAP Id 221)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.354: 00:24:d6:97:b3:be Reusing allocated memory for EAP Pkt for retransmission to mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.354: 00:24:d6:97:b3:be mscb->apfMsLwappLradNhMac = 00:00:0c:07:ac:dc mscb->apfMsLradSlotId = 1 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.354: 00:24:d6:97:b3:be mscb->apfMsBssid = 18:33:9d:f0:21:80 mscb->apfMsAddress = 00:24:d6:97:b3:be mscb->apfMsApVapId = 2
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.354: 00:24:d6:97:b3:be dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 220 mscb->apfMsLwappMwarInet.ipv4.addr = 176217288
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.354: 00:24:d6:97:b3:be mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = 176325157 mscb->apfMsLwappLradPort = 9385
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.359: 00:24:d6:97:b3:be Received EAPOL EAPPKT from mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.359: 00:24:d6:97:b3:be Received EAP Response from mobile 00:24:d6:97:b3:be (EAP Id 221, EAP Type 13)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.359: 00:24:d6:97:b3:be Resetting reauth count 0 to 0 for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.359: 00:24:d6:97:b3:be Entering Backend Auth Response state for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.360: 00:24:d6:97:b3:be Processing Access-Challenge for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.360: 00:24:d6:97:b3:be Entering Backend Auth Req state (id=222) for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.360: 00:24:d6:97:b3:be Sending EAP Request from AAA to mobile 00:24:d6:97:b3:be (EAP Id 222)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.360: 00:24:d6:97:b3:be Reusing allocated memory for EAP Pkt for retransmission to mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.360: 00:24:d6:97:b3:be mscb->apfMsLwappLradNhMac = 00:00:0c:07:ac:dc mscb->apfMsLradSlotId = 1 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.360: 00:24:d6:97:b3:be mscb->apfMsBssid = 18:33:9d:f0:21:80 mscb->apfMsAddress = 00:24:d6:97:b3:be mscb->apfMsApVapId = 2
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.360: 00:24:d6:97:b3:be dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 220 mscb->apfMsLwappMwarInet.ipv4.addr = 176217288
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.360: 00:24:d6:97:b3:be mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = 176325157 mscb->apfMsLwappLradPort = 9385
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.365: 00:24:d6:97:b3:be Received EAPOL EAPPKT from mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.365: 00:24:d6:97:b3:be Received EAP Response from mobile 00:24:d6:97:b3:be (EAP Id 222, EAP Type 13)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.365: 00:24:d6:97:b3:be Resetting reauth count 0 to 0 for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.365: 00:24:d6:97:b3:be Entering Backend Auth Response state for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.366: 00:24:d6:97:b3:be Processing Access-Challenge for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.366: 00:24:d6:97:b3:be Entering Backend Auth Req state (id=223) for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.366: 00:24:d6:97:b3:be Sending EAP Request from AAA to mobile 00:24:d6:97:b3:be (EAP Id 223)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.366: 00:24:d6:97:b3:be Reusing allocated memory for EAP Pkt for retransmission to mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.366: 00:24:d6:97:b3:be mscb->apfMsLwappLradNhMac = 00:00:0c:07:ac:dc mscb->apfMsLradSlotId = 1 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.366: 00:24:d6:97:b3:be mscb->apfMsBssid = 18:33:9d:f0:21:80 mscb->apfMsAddress = 00:24:d6:97:b3:be mscb->apfMsApVapId = 2
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.366: 00:24:d6:97:b3:be dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 220 mscb->apfMsLwappMwarInet.ipv4.addr = 176217288
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.366: 00:24:d6:97:b3:be mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = 176325157 mscb->apfMsLwappLradPort = 9385
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.371: 00:24:d6:97:b3:be Received EAPOL EAPPKT from mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.371: 00:24:d6:97:b3:be Received EAP Response from mobile 00:24:d6:97:b3:be (EAP Id 223, EAP Type 13)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.371: 00:24:d6:97:b3:be Resetting reauth count 0 to 0 for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.371: 00:24:d6:97:b3:be Entering Backend Auth Response state for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.372: 00:24:d6:97:b3:be Processing Access-Challenge for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.372: 00:24:d6:97:b3:be Entering Backend Auth Req state (id=224) for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.372: 00:24:d6:97:b3:be Sending EAP Request from AAA to mobile 00:24:d6:97:b3:be (EAP Id 224)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.372: 00:24:d6:97:b3:be Reusing allocated memory for EAP Pkt for retransmission to mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.372: 00:24:d6:97:b3:be mscb->apfMsLwappLradNhMac = 00:00:0c:07:ac:dc mscb->apfMsLradSlotId = 1 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.372: 00:24:d6:97:b3:be mscb->apfMsBssid = 18:33:9d:f0:21:80 mscb->apfMsAddress = 00:24:d6:97:b3:be mscb->apfMsApVapId = 2
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.372: 00:24:d6:97:b3:be dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 220 mscb->apfMsLwappMwarInet.ipv4.addr = 176217288
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.372: 00:24:d6:97:b3:be mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = 176325157 mscb->apfMsLwappLradPort = 9385
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.375: 00:24:d6:97:b3:be Received EAPOL EAPPKT from mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.375: 00:24:d6:97:b3:be Received EAP Response from mobile 00:24:d6:97:b3:be (EAP Id 224, EAP Type 13)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.375: 00:24:d6:97:b3:be Resetting reauth count 0 to 0 for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.375: 00:24:d6:97:b3:be Entering Backend Auth Response state for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.389: 00:24:d6:97:b3:be Processing Access-Challenge for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.389: 00:24:d6:97:b3:be Entering Backend Auth Req state (id=225) for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.389: 00:24:d6:97:b3:be Sending EAP Request from AAA to mobile 00:24:d6:97:b3:be (EAP Id 225)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.389: 00:24:d6:97:b3:be Reusing allocated memory for EAP Pkt for retransmission to mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.389: 00:24:d6:97:b3:be mscb->apfMsLwappLradNhMac = 00:00:0c:07:ac:dc mscb->apfMsLradSlotId = 1 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.389: 00:24:d6:97:b3:be mscb->apfMsBssid = 18:33:9d:f0:21:80 mscb->apfMsAddress = 00:24:d6:97:b3:be mscb->apfMsApVapId = 2
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.389: 00:24:d6:97:b3:be dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 220 mscb->apfMsLwappMwarInet.ipv4.addr = 176217288
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.389: 00:24:d6:97:b3:be mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = 176325157 mscb->apfMsLwappLradPort = 9385
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.391: 00:24:d6:97:b3:be Received EAPOL EAPPKT from mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.391: 00:24:d6:97:b3:be Received EAP Response from mobile 00:24:d6:97:b3:be (EAP Id 225, EAP Type 13)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.391: 00:24:d6:97:b3:be Resetting reauth count 0 to 0 for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.391: 00:24:d6:97:b3:be Entering Backend Auth Response state for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Processing Access-Accept for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Resetting web IPv4 acl from 255 to 255
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Resetting web IPv4 Flex acl from 65535 to 65535
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Username entry ([email protected]) created for mobile, length = 253
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Username entry ([email protected]) created in mscb for mobile, length = 253
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be override for default ap group, marking intgrp NULL
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Applying Interface policy on Mobile, role Unassociated. Ms NAC State 2 Quarantine Vlan 0 Access Vlan 220
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Re-applying interface policy for client
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be 0.0.0.0 8021X_REQD (3) Changing IPv4 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2219)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be 0.0.0.0 8021X_REQD (3) Changing IPv6 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2240)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be apfApplyWlanPolicy: Retaining the ACL recieved in AAA attributes 1 on mobile
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be apfApplyWlanPolicy: Apply WLAN Policy over PMIPv6 Client Mobility Type
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Inserting AAA Override struct for mobile
MAC: 00:24:d6:97:b3:be, source 4
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Setting re-auth timeout to 1800 seconds, got from WLAN config.
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Station 00:24:d6:97:b3:be setting dot1x reauth timeout = 1800
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Creating a PKC PMKID Cache entry for station 00:24:d6:97:b3:be (RSN 2)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Resetting MSCB PMK Cache Entry 0 for station 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Setting active key cache index 8 ---> 8
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Setting active key cache index 8 ---> 0
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Adding BSSID 18:33:9d:f0:21:8e to PMKID cache at index 0 for station 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: New PMKID: (16)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: [0000] 6f d1 ce 84 08 74 41 a5 06 6b 89 02 c9 e9 f8 c8
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Disabling re-auth since PMK lifetime can take care of same.
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be unsetting PmkIdValidatedByAp
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Client in Posture Reqd state. PMK cache not updated.
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Sending EAP-Success to mobile 00:24:d6:97:b3:be (EAP Id 225)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be mscb->apfMsLwappLradNhMac = 00:00:0c:07:ac:dc mscb->apfMsLradSlotId = 1 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be mscb->apfMsBssid = 18:33:9d:f0:21:80 mscb->apfMsAddress = 00:24:d6:97:b3:be mscb->apfMsApVapId = 2
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 220 mscb->apfMsLwappMwarInet.ipv4.addr = 176217288
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = 176325157 mscb->apfMsLwappLradPort = 9385
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Freeing AAACB from Dot1xCB as AAA auth is done for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be EAPOL Header:
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00000000: 02 03 5f 00 .._.
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Found an cache entry for BSSID 18:33:9d:f0:21:8e in PMKID cache at index 0 of station 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Found an cache entry for BSSID 18:33:9d:f0:21:8e in PMKID cache at index 0 of station 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: Including PMKID in M1 (16)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: [0000] 6f d1 ce 84 08 74 41 a5 06 6b 89 02 c9 e9 f8 c8
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Starting key exchange to mobile 00:24:d6:97:b3:be, data packets will be dropped
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Sending EAPOL-Key Message to mobile 00:24:d6:97:b3:be
state INITPMK (message 1), replay counter 00.00.00.00.00.00.00.00
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Sending EAPOL-Key Message to mobile 00:24:d6:97:b3:be
state INITPMK (message 1), replay counter 00.00.00.00.00.00.00.00
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Reusing allocated memory for EAP Pkt for retransmission to mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be mscb->apfMsLwappLradNhMac = 00:00:0c:07:ac:dc mscb->apfMsLradSlotId = 1 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be mscb->apfMsBssid = 18:33:9d:f0:21:80 mscb->apfMsAddress = 00:24:d6:97:b3:be mscb->apfMsApVapId = 2
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 220 mscb->apfMsLwappMwarInet.ipv4.addr = 176217288
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = 176325157 mscb->apfMsLwappLradPort = 9385
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Entering Backend Auth Success state (id=225) for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Received Auth Success while in Authenticating state for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be dot1x - moving mobile 00:24:d6:97:b3:be into Authenticated state
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.414: 00:24:d6:97:b3:be Received EAPOL-Key from mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.414: 00:24:d6:97:b3:be Received EAPOL-key in PTK_START state (message 2) from mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.414: 00:24:d6:97:b3:be PMK: Sending cache add
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.414: 00:24:d6:97:b3:be Stopping retransmission timer for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.414: 00:24:d6:97:b3:be EAPOL Header:
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.414: 00000000: 02 03 5f 00 .._.
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.414: 00:24:d6:97:b3:be Sending EAPOL-Key Message to mobile 00:24:d6:97:b3:be
state PTKINITNEGOTIATING (message 3), replay counter 00.00.00.00.00.00.00.01
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.414: 00:24:d6:97:b3:be Sending EAPOL-Key Message to mobile 00:24:d6:97:b3:be
state PTKINITNEGOTIATING (message 3), replay counter 00.00.00.00.00.00.00.01
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.414: 00:24:d6:97:b3:be Reusing allocated memory for EAP Pkt for retransmission to mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.414: 00:24:d6:97:b3:be mscb->apfMsLwappLradNhMac = 00:00:0c:07:ac:dc mscb->apfMsLradSlotId = 1 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.414: 00:24:d6:97:b3:be mscb->apfMsBssid = 18:33:9d:f0:21:80 mscb->apfMsAddress = 00:24:d6:97:b3:be mscb->apfMsApVapId = 2
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.414: 00:24:d6:97:b3:be dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 220 mscb->apfMsLwappMwarInet.ipv4.addr = 176217288
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.414: 00:24:d6:97:b3:be mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = 176325157 mscb->apfMsLwappLradPort = 9385
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be Received EAPOL-Key from mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be Received EAPOL-key in PTKINITNEGOTIATING state (message 4) from mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be Stopping retransmission timer for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be Freeing EAP Retransmit Bufer for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be apfMs1xStateInc
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be 0.0.0.0 8021X_REQD (3) Change state to L2AUTHCOMPLETE (4) last state 8021X_REQD (3)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be Central switch is FALSE
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be Sending the Central Auth Info
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be Central Auth Info Allocated PMKLen = 32
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: EapolReplayCounter: 00 00 00 00 00 00 00 01
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: EapolReplayCounter: 00 00 00 00 00 00 00 01
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be PMK: pmkActiveIndex = 0
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be EapolReplayCounter: 00 00 00 00 00 00 00 01
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be msAssocTypeFlagsMsb = 0 msAssocTypeFlagsLsb = 2
apfMsEntryType = 0 apfMsEapType = 13
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be 0.0.0.0 L2AUTHCOMPLETE (4) DHCP required on AP 18:33:9d:f0:21:80 vapId 2 apVapId 2for this client
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be Not Using WMM Compliance code qosCap 00
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be 0.0.0.0 L2AUTHCOMPLETE (4) Plumbed mobile LWAPP rule on AP 18:33:9d:f0:21:80 vapId 2 apVapId 2 flex-acl-name:POSTURE_REDIRECT_ACL
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be 0.0.0.0 L2AUTHCOMPLETE (4) Change state to DHCP_REQD (7) last state L2AUTHCOMPLETE (4)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be 0.0.0.0 DHCP_REQD (7) pemAdvanceState2 6166, Adding TMP rule
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be 0.0.0.0 DHCP_REQD (7) Adding Fast Path rule
type = Airespace AP - Learn IP address
on AP 18:33:9d:f0:21:80, slot 1, interface = 1, QOS = 0
IPv4 ACL ID = 255, IPv
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be 0.0.0.0 DHCP_REQD (7) Fast Path rule (contd...) 802.1P = 0, DSCP = 0, TokenID = 64206 Local Bridging Vlan = 220, Local Bridging intf id = 0
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be 0.0.0.0 DHCP_REQD (7) Successfully plumbed mobile rule (IPv4 ACL ID 255, IPv6 ACL ID 255, L2 ACL ID 255)
*apfReceiveTask: Aug 12 10:58:24.418: 00:24:d6:97:b3:be 0.0.0.0 DHCP_REQD (7) State Update from Mobility-Incomplete to Mobility-Complete, mobility role=Local, client state=APF_MS_STATE_ASSOCIATED
*apfReceiveTask: Aug 12 10:58:24.418: 00:24:d6:97:b3:be 0.0.0.0 DHCP_REQD (7) pemAdvanceState2 5761, Adding TMP rule
*apfReceiveTask: Aug 12 10:58:24.418: 00:24:d6:97:b3:be 0.0.0.0 DHCP_REQD (7) Replacing Fast Path rule
type = Airespace AP - Learn IP address
on AP 18:33:9d:f0:21:80, slot 1, interface = 1, QOS = 0
IPv4 ACL ID = 255,
*apfReceiveTask: Aug 12 10:58:24.418: 00:24:d6:97:b3:be 0.0.0.0 DHCP_REQD (7) Fast Path rule (contd...) 802.1P = 0, DSCP = 0, TokenID = 64206 Local Bridging Vlan = 220, Local Bridging intf id = 0
*apfReceiveTask: Aug 12 10:58:24.418: 00:24:d6:97:b3:be 0.0.0.0 DHCP_REQD (7) Successfully plumbed mobile rule (IPv4 ACL ID 255, IPv6 ACL ID 255, L2 ACL ID 255)
*pemReceiveTask: Aug 12 10:58:24.418: 00:24:d6:97:b3:be 0.0.0.0 Added NPU entry of type 9, dtlFlags 0x0
*pemReceiveTask: Aug 12 10:58:24.418: 00:24:d6:97:b3:be 0.0.0.0 Added NPU entry of type 9, dtlFlags 0x0
*spamApTask6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be spamEncodeCentralAuthInoMsPayload: msAssocTypeFlagsMsb = 0 msAssocTypeFlagsLsb = 2
apfMsEntryType = 0 pmkLen = 32
*DHCP Socket Task: Aug 12 10:58:24.546: 00:24:d6:97:b3:be DHCP received op BOOTREPLY (2) (len 325,vlan 220, port 1, encap 0xec03)
*DHCP Socket Task: Aug 12 10:58:24.546: 00:24:d6:97:b3:be DHCP setting server from ACK (server 10.0.17.85, yiaddr 10.130.130.120)
*DHCP Socket Task: Aug 12 10:58:24.548: 00:24:d6:97:b3:be 10.130.130.120 DHCP_REQD (7) Change state to WEBAUTH_REQD (8) last state DHCP_REQD (7)
*DHCP Socket Task: Aug 12 10:58:24.548: 00:24:d6:97:b3:be 10.130.130.120 WEBAUTH_REQD (8) pemAdvanceState2 6671, Adding TMP rule
*DHCP Socket Task: Aug 12 10:58:24.548: 00:24:d6:97:b3:be 10.130.130.120 WEBAUTH_REQD (8) Replacing Fast Path rule
type = Airespace AP Client - ACL passthru
on AP 18:33:9d:f0:21:80, slot 1, interface = 1, QOS = 0
IPv4 A
*DHCP Socket Task: Aug 12 10:58:24.548: 00:24:d6:97:b3:be 10.130.130.120 WEBAUTH_REQD (8) Fast Path rule (contd...) 802.1P = 0, DSCP = 0, TokenID = 64206 Local Bridging Vlan = 220, Local Bridging intf id = 0
*DHCP Socket Task: Aug 12 10:58:24.548: 00:24:d6:97:b3:be 10.130.130.120 WEBAUTH_REQD (8) Successfully plumbed mobile rule (IPv4 ACL ID 1, IPv6 ACL ID 255, L2 ACL ID 255)
*DHCP Socket Task: Aug 12 10:58:24.548: 00:24:d6:97:b3:be Plumbing web-auth redirect rule due to user logout
*DHCP Socket Task: Aug 12 10:58:24.548: 00:24:d6:97:b3:be Assigning Address 10.130.130.120 to mobile
*DHCP Socket Task: Aug 12 10:58:24.548: 00:24:d6:97:b3:be DHCP success event for client. Clearing dhcp failure count for interface management.
*DHCP Socket Task: Aug 12 10:58:24.548: 00:24:d6:97:b3:be DHCP success event for client. Clearing dhcp failure count for interface management.
*pemReceiveTask: Aug 12 10:58:24.548: 00:24:d6:97:b3:be 10.130.130.120 Added NPU entry of type 2, dtlFlags 0x0
*IPv6_Msg_Task: Aug 12 10:58:25.330: 00:24:d6:97:b3:be Pushing IPv6 Vlan Intf ID 0: fe80:0000:0000:0000:f524:1910:69f0:9482 , and MAC: 00:24:D6:97:B3:BE , Binding to Data Plane. SUCCESS !! dhcpv6bitmap 0
*IPv6_Msg_Task: Aug 12 10:58:25.330: 00:24:d6:97:b3:be Link Local address fe80::f524:1910:69f0:9482 updated to mscb. Not Advancing pem state.Current state: mscb in apfMsMmInitial mobility state and client state APF_MS_STATE_A
*DHCP Socket Task: Aug 12 10:58:28.581: 00:24:d6:97:b3:be DHCP received op BOOTREPLY (2) (len 308,vlan 220, port 1, encap 0xec03)
*DHCP Socket Task: Aug 12 10:58:28.589: 00:24:d6:97:b3:be DHCP received op BOOTREPLY (2) (len 308,vlan 220, port 1, encap 0xec03)
*DHCP Socket Task: Aug 12 11:00:07.959: 00:24:d6:97:b3:be DHCP received op BOOTREPLY (2) (len 308,vlan 220, port 1, encap 0xec03)
*DHCP Socket Task: Aug 12 11:00:07.967: 00:24:d6:97:b3:be DHCP received op BOOTREPLY (2) (len 308,vlan 220, port 1, encap 0xec03)
*DHCP Socket Task: Aug 12 11:01:59.153: 00:24:d6:97:b3:be DHCP received op BOOTREPLY (2) (len 308,vlan 220, port 1, encap 0xec03)
Can you see any obvious reason why the NAC agent wont pop up?
Thanks
Mario -
WLC 5508, SW 6.0.199.4, 1142 AP: Clients getting dropped intermittently
We have deployed a WLC 5508 w/ SW version 6.0.199.4, 1142 AP's & open authentication w/ MAC filtering. Clients are randomly getting dropped with "Limited Access" shown in Win 7. In this state, the client machine is unable to ping the gateway and sometimes lose their DHCP assigned IP as well. A manual disconnect/re-connect to the SSID is required everytime.
I ran a debug on one the clients stuck in the "Limited Access" state (debug client xx:xx:xx:xx):
*Apr 15 16:59:23.205: e0:91:53:60:1f:e4 Adding mobile on LWAPP AP 3c:ce:73:c5:1e:b0(0)
*Apr 15 16:59:23.205: e0:91:53:60:1f:e4 Scheduling deletion of Mobile Station: (callerId: 23) in 5 seconds
*Apr 15 16:59:23.205: e0:91:53:60:1f:e4 apfProcessProbeReq (apf_80211.c:4722) Changing state for mobile e0:91:53:60:1f:e4 on AP 3c:ce:73:c5:1e:b0 from Idle to Probe
*Apr 15 16:59:23.205: e0:91:53:60:1f:e4 Scheduling deletion of Mobile Station: (callerId: 24) in 5 seconds
*Apr 15 16:59:23.225: e0:91:53:60:1f:e4 Scheduling deletion of Mobile Station: (callerId: 24) in 5 seconds
*Apr 15 16:59:23.225: e0:91:53:60:1f:e4 Scheduling deletion of Mobile Station: (callerId: 24) in 5 seconds
*Apr 15 16:59:23.646: e0:91:53:60:1f:e4 Scheduling deletion of Mobile Station: (callerId: 24) in 5 seconds
*Apr 15 16:59:23.646: e0:91:53:60:1f:e4 Scheduling deletion of Mobile Station: (callerId: 24) in 5 seconds
*Apr 15 16:59:23.666: e0:91:53:60:1f:e4 Scheduling deletion of Mobile Station: (callerId: 24) in 5 seconds
*Apr 15 16:59:23.666: e0:91:53:60:1f:e4 Scheduling deletion of Mobile Station: (callerId: 24) in 5 seconds
*Apr 15 16:59:28.553: e0:91:53:60:1f:e4 apfMsExpireCallback (apf_ms.c:418) Expiring Mobile!
*Apr 15 16:59:28.554: e0:91:53:60:1f:e4 0.0.0.0 START (0) Deleted mobile LWAPP rule on AP [3c:ce:73:c5:1e:b0]
*Apr 15 16:59:28.554: e0:91:53:60:1f:e4 Deleting mobile on AP 3c:ce:73:c5:1e:b0(0)
On doing a manual re-connect, got the following logs:
*Apr 15 17:01:38.143: e0:91:53:60:1f:e4 Association received from mobile on AP b8:62:1f:e9:9f:30
*Apr 15 17:01:38.143: e0:91:53:60:1f:e4 Applying site-specific IPv6 override for station e0:91:53:60:1f:e4 - vapId 7, site 'Academy', interface 'students'
*Apr 15 17:01:38.143: e0:91:53:60:1f:e4 Applying IPv6 Interface Policy for station e0:91:53:60:1f:e4 - vlan 15, interface id 14, interface 'students'
*Apr 15 17:01:38.143: e0:91:53:60:1f:e4 Applying site-specific override for station e0:91:53:60:1f:e4 - vapId 7, site 'Academy', interface 'students'
*Apr 15 17:01:38.143: e0:91:53:60:1f:e4 0.0.0.0 START (0) Changing ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:1276)
*Apr 15 17:01:38.143: e0:91:53:60:1f:e4 STA - rates (8): 130 132 139 150 12 18 24 36 0 0 0 0 0 0 0 0
*Apr 15 17:01:38.143: e0:91:53:60:1f:e4 STA - rates (12): 130 132 139 150 12 18 24 36 48 72 96 108 0 0 0 0
*Apr 15 17:01:38.143: e0:91:53:60:1f:e4 0.0.0.0 START (0) Deleted mobile LWAPP rule on AP [b8:62:1f:e5:6a:90]
*Apr 15 17:01:38.144: e0:91:53:60:1f:e4 Updated location for station old AP b8:62:1f:e5:6a:90-0, new AP b8:62:1f:e9:9f:30-0
*Apr 15 17:01:38.144: e0:91:53:60:1f:e4 apfProcessAssocReq (apf_80211.c:4268) Changing state for mobile e0:91:53:60:1f:e4 on AP b8:62:1f:e9:9f:30 from Probe to AAA Pending
*Apr 15 17:01:38.144: e0:91:53:60:1f:e4 Scheduling deletion of Mobile Station: (callerId: 20) in 10 seconds
*Apr 15 17:01:38.144: e0:91:53:60:1f:e4 0.0.0.0 START (0) Initializing policy
*Apr 15 17:01:38.144: e0:91:53:60:1f:e4 0.0.0.0 START (0) Change state to AUTHCHECK (2) last state AUTHCHECK (2)
*Apr 15 17:01:38.144: e0:91:53:60:1f:e4 0.0.0.0 AUTHCHECK (2) Change state to L2AUTHCOMPLETE (4) last state L2AUTHCOMPLETE (4)
*Apr 15 17:01:38.144: e0:91:53:60:1f:e4 0.0.0.0 L2AUTHCOMPLETE (4) Plumbed mobile LWAPP rule on AP b8:62:1f:e9:9f:30 vapId 7 apVapId 2
*Apr 15 17:01:38.144: e0:91:53:60:1f:e4 0.0.0.0 L2AUTHCOMPLETE (4) Change state to DHCP_REQD (7) last state DHCP_REQD (7)
*Apr 15 17:01:38.144: e0:91:53:60:1f:e4 apfPemAddUser2 (apf_policy.c:213) Changing state for mobile e0:91:53:60:1f:e4 on AP b8:62:1f:e9:9f:30 from AAA Pending to Associated
*Apr 15 17:01:38.145: e0:91:53:60:1f:e4 Scheduling deletion of Mobile Station: (callerId: 49) in 65535 seconds
*Apr 15 17:01:38.145: e0:91:53:60:1f:e4 Including FT Mobility Domain IE (length 5) in Initial assoc Resp to mobile
*Apr 15 17:01:38.145: e0:91:53:60:1f:e4 Sending Assoc Response to station on BSSID b8:62:1f:e9:9f:30 (status 0) Vap Id 2 Slot 0
*Apr 15 17:01:38.145: e0:91:53:60:1f:e4 apfProcessRadiusAssocResp (apf_80211.c:1957) Changing state for mobile e0:91:53:60:1f:e4 on AP b8:62:1f:e9:9f:30 from Associated to Associated
*Apr 15 17:01:38.189: e0:91:53:60:1f:e4 DHCP received op BOOTREQUEST (1) (len 308, port 13, encap 0xec03)
*Apr 15 17:01:38.189: e0:91:53:60:1f:e4 DHCP dropping packet due to ongoing mobility handshake exchange, (siaddr 0.0.0.0, mobility state = 'apfMsMmQueryRequested'
*Apr 15 17:01:39.953: e0:91:53:60:1f:e4 0.0.0.0 DHCP_REQD (7) State Update from Mobility-Incomplete to Mobility-Complete, mobility role=Local, client state=APF_MS_STATE_ASSOCIATED
*Apr 15 17:01:39.954: e0:91:53:60:1f:e4 0.0.0.0 DHCP_REQD (7) pemAdvanceState2 4166, Adding TMP rule
*Apr 15 17:01:39.954: e0:91:53:60:1f:e4 0.0.0.0 DHCP_REQD (7) Adding Fast Path rule
type = Airespace AP - Learn IP address
on AP b8:62:1f:e9:9f:30, slot 0, interface = 13, QOS = 0
ACL Id = 255, Jumbo F
*Apr 15 17:01:39.954: e0:91:53:60:1f:e4 0.0.0.0 DHCP_REQD (7) Successfully plumbed mobile rule (ACL ID 255)
*Apr 15 17:01:39.954: e0:91:53:60:1f:e4 0.0.0.0 Added NPU entry of type 9, dtlFlags 0x0
*Apr 15 17:01:39.954: e0:91:53:60:1f:e4 Sent an XID frame
*Apr 15 17:01:40.807: e0:91:53:60:1f:e4 Orphan Packet from STA - IP 169.254.201.128
*Apr 15 17:01:43.234: e0:91:53:60:1f:e4 DHCP received op BOOTREQUEST (1) (len 308, port 13, encap 0xec03)
*Apr 15 17:01:43.234: e0:91:53:60:1f:e4 DHCP processing DHCP DISCOVER (1)
*Apr 15 17:01:43.234: e0:91:53:60:1f:e4 DHCP op: BOOTREQUEST, htype: Ethernet, hlen: 6, hops: 0
*Apr 15 17:01:43.234: e0:91:53:60:1f:e4 DHCP xid: 0x9b24c896 (2602879126), secs: 1280, flags: 0
*Apr 15 17:01:43.234: e0:91:53:60:1f:e4 DHCP chaddr: e0:91:53:60:1f:e4
*Apr 15 17:01:43.234: e0:91:53:60:1f:e4 DHCP ciaddr: 0.0.0.0, yiaddr: 0.0.0.0
*Apr 15 17:01:43.234: e0:91:53:60:1f:e4 DHCP siaddr: 0.0.0.0, giaddr: 0.0.0.0
*Apr 15 17:01:43.234: e0:91:53:60:1f:e4 DHCP successfully bridged packet to DS
*Apr 15 17:01:43.234: e0:91:53:60:1f:e4 DHCP received op BOOTREPLY (2) (len 308, port 13, encap 0xec00)
*Apr 15 17:01:43.234: e0:91:53:60:1f:e4 DHCP processing DHCP OFFER (2)
*Apr 15 17:01:43.234: e0:91:53:60:1f:e4 DHCP op: BOOTREPLY, htype: Ethernet, hlen: 6, hops: 0
*Apr 15 17:01:43.234: e0:91:53:60:1f:e4 DHCP xid: 0x9b24c896 (2602879126), secs: 0, flags: 0
*Apr 15 17:01:43.234: e0:91:53:60:1f:e4 DHCP chaddr: e0:91:53:60:1f:e4
*Apr 15 17:01:43.235: e0:91:53:60:1f:e4 DHCP ciaddr: 0.0.0.0, yiaddr: 10.6.2.160
*Apr 15 17:01:43.235: e0:91:53:60:1f:e4 DHCP siaddr: 0.0.0.0, giaddr: 0.0.0.0
*Apr 15 17:01:43.235: e0:91:53:60:1f:e4 DHCP server id: 10.6.15.254 rcvd server id: 10.6.15.254
*Apr 15 17:01:43.235: e0:91:53:60:1f:e4 DHCP successfully bridged packet to STA
*Apr 15 17:01:43.240: e0:91:53:60:1f:e4 DHCP received op BOOTREQUEST (1) (len 316, port 13, encap 0xec03)
*Apr 15 17:01:43.241: e0:91:53:60:1f:e4 DHCP processing DHCP REQUEST (3)
*Apr 15 17:01:43.241: e0:91:53:60:1f:e4 DHCP op: BOOTREQUEST, htype: Ethernet, hlen: 6, hops: 0
*Apr 15 17:01:43.241: e0:91:53:60:1f:e4 DHCP xid: 0x9b24c896 (2602879126), secs: 1280, flags: 0
*Apr 15 17:01:43.241: e0:91:53:60:1f:e4 DHCP chaddr: e0:91:53:60:1f:e4
*Apr 15 17:01:43.241: e0:91:53:60:1f:e4 DHCP ciaddr: 0.0.0.0, yiaddr: 0.0.0.0
*Apr 15 17:01:43.241: e0:91:53:60:1f:e4 DHCP siaddr: 0.0.0.0, giaddr: 0.0.0.0
*Apr 15 17:01:43.241: e0:91:53:60:1f:e4 DHCP requested ip: 10.6.2.160
*Apr 15 17:01:43.241: e0:91:53:60:1f:e4 DHCP server id: 10.6.15.254 rcvd server id: 10.6.15.254
*Apr 15 17:01:43.241: e0:91:53:60:1f:e4 DHCP successfully bridged packet to DS
*Apr 15 17:01:43.241: e0:91:53:60:1f:e4 DHCP received op BOOTREPLY (2) (len 308, port 13, encap 0xec00)
*Apr 15 17:01:43.241: e0:91:53:60:1f:e4 DHCP processing DHCP ACK (5)
*Apr 15 17:01:43.241: e0:91:53:60:1f:e4 DHCP op: BOOTREPLY, htype: Ethernet, hlen: 6, hops: 0
*Apr 15 17:01:43.241: e0:91:53:60:1f:e4 DHCP xid: 0x9b24c896 (2602879126), secs: 0, flags: 0
*Apr 15 17:01:43.241: e0:91:53:60:1f:e4 DHCP chaddr: e0:91:53:60:1f:e4
*Apr 15 17:01:43.241: e0:91:53:60:1f:e4 DHCP ciaddr: 0.0.0.0, yiaddr: 10.6.2.160
*Apr 15 17:01:43.241: e0:91:53:60:1f:e4 DHCP siaddr: 0.0.0.0, giaddr: 0.0.0.0
*Apr 15 17:01:43.241: e0:91:53:60:1f:e4 DHCP server id: 10.6.15.254 rcvd server id: 10.6.15.254
*Apr 15 17:01:43.242: e0:91:53:60:1f:e4 10.6.2.160 DHCP_REQD (7) Change state to RUN (20) last state RUN (20)
*Apr 15 17:01:43.242: e0:91:53:60:1f:e4 10.6.2.160 RUN (20) Reached PLUMBFASTPATH: from line 4972
*Apr 15 17:01:43.242: e0:91:53:60:1f:e4 10.6.2.160 RUN (20) Replacing Fast Path rule
type = Airespace AP Client
on AP b8:62:1f:e9:9f:30, slot 0, interface = 13, QOS = 0
ACL Id = 255, Jumbo Frames = NO,
*Apr 15 17:01:43.242: e0:91:53:60:1f:e4 10.6.2.160 RUN (20) Successfully plumbed mobile rule (ACL ID 255)
*Apr 15 17:01:43.242: e0:91:53:60:1f:e4 Assigning Address 10.6.2.160 to mobile
*Apr 15 17:01:43.242: e0:91:53:60:1f:e4 DHCP successfully bridged packet to STA
*Apr 15 17:01:43.242: e0:91:53:60:1f:e4 10.6.2.160 Added NPU entry of type 1, dtlFlags 0x0
*Apr 15 17:01:43.242: e0:91:53:60:1f:e4 Sending a gratuitous ARP for 10.6.2.160, VLAN Id 15
*Apr 15 17:01:46.428: e0:91:53:60:1f:e4 DHCP received op BOOTREQUEST (1) (len 308, port 13, encap 0xec03)
*Apr 15 17:01:46.428: e0:91:53:60:1f:e4 DHCP processing DHCP INFORM (8)
*Apr 15 17:01:46.429: e0:91:53:60:1f:e4 DHCP op: BOOTREQUEST, htype: Ethernet, hlen: 6, hops: 0
*Apr 15 17:01:46.429: e0:91:53:60:1f:e4 DHCP xid: 0xbb0d5d87 (3138215303), secs: 0, flags: 0
*Apr 15 17:01:46.429: e0:91:53:60:1f:e4 DHCP chaddr: e0:91:53:60:1f:e4
*Apr 15 17:01:46.429: e0:91:53:60:1f:e4 DHCP ciaddr: 10.6.2.160, yiaddr: 0.0.0.0
*Apr 15 17:01:46.429: e0:91:53:60:1f:e4 DHCP siaddr: 0.0.0.0, giaddr: 0.0.0.0
*Apr 15 17:01:46.429: e0:91:53:60:1f:e4 DHCP successfully bridged packet to DS
*Apr 15 17:01:46.429: e0:91:53:60:1f:e4 DHCP received op BOOTREPLY (2) (len 308, port 13, encap 0xec00)
*Apr 15 17:01:46.429: e0:91:53:60:1f:e4 DHCP processing DHCP ACK (5)
*Apr 15 17:01:46.429: e0:91:53:60:1f:e4 DHCP op: BOOTREPLY, htype: Ethernet, hlen: 6, hops: 0
*Apr 15 17:01:46.429: e0:91:53:60:1f:e4 DHCP xid: 0xbb0d5d87 (3138215303), secs: 0, flags: 0
*Apr 15 17:01:46.429: e0:91:53:60:1f:e4 DHCP chaddr: e0:91:53:60:1f:e4
*Apr 15 17:01:46.429: e0:91:53:60:1f:e4 DHCP ciaddr: 10.6.2.160, yiaddr: 0.0.0.0
*Apr 15 17:01:46.429: e0:91:53:60:1f:e4 DHCP siaddr: 0.0.0.0, giaddr: 0.0.0.0
*Apr 15 17:01:46.429: e0:91:53:60:1f:e4 DHCP server id: 10.6.15.254 rcvd server id: 10.6.15.254
show client e0:91:53:60:1f:e4 (after re-connect)
(Cisco Controller) >show client detail e0:91:53:60:1f:e4
Client MAC Address............................... e0:91:53:60:1f:e4
Client Username ................................. N/A
AP MAC Address................................... b8:62:1f:e9:9f:30
Client State..................................... Associated
Client NAC OOB State............................. Access
Wireless LAN Id.................................. 7
BSSID............................................ b8:62:1f:e9:9f:31
Connected For ................................... 105 secs
Channel.......................................... 11
IP Address....................................... 10.6.2.160
Association Id................................... 8
Authentication Algorithm......................... Open System
Reason Code...................................... 1
Status Code...................................... 0
Session Timeout.................................. 65535
Client CCX version............................... No CCX support
QoS Level........................................ Silver
Diff Serv Code Point (DSCP)...................... disabled
802.1P Priority Tag.............................. disabled
WMM Support...................................... Enabled
U-APSD Support................................... Disabled
Power Save....................................... OFF
Current Rate..................................... m7
Supported Rates.................................. 1.0,2.0,5.5,11.0,6.0,9.0,
............................................. 12.0,18.0,24.0,36.0,48.0,
............................................. 54.0
Mobility State................................... Local
Mobility Move Count.............................. 0
Security Policy Completed........................ Yes
Policy Manager State............................. RUN
Policy Manager Rule Created...................... Yes
ACL Name......................................... none
ACL Applied Status............................... Unavailable
Policy Type...................................... N/A
Encryption Cipher................................ None
Management Frame Protection...................... No
EAP Type......................................... Unknown
Interface........................................ students
VLAN............................................. 15
Quarantine VLAN.................................. 0
Access VLAN...................................... 15
Client Capabilities:
CF Pollable................................ Not implemented
CF Poll Request............................ Not implemented
Short Preamble............................. Implemented
PBCC....................................... Not implemented
Channel Agility............................ Not implemented
Listen Interval............................ 1
Fast BSS Transition........................ Not implemented
Fast BSS Transition Details:
Client Statistics:
Number of Bytes Received................... 36509
Number of Bytes Sent....................... 32902
Number of Packets Received................. 300
Number of Packets Sent..................... 66
Number of EAP Id Request Msg Timeouts...... 0
Number of EAP Request Msg Timeouts......... 0
Number of EAP Key Msg Timeouts............. 0
Number of Data Retries..................... 95
Number of RTS Retries...................... 0
Number of Duplicate Received Packets....... 1
Number of Decrypt Failed Packets........... 0
Number of Mic Failured Packets............. 0
Number of Mic Missing Packets.............. 0
Number of Policy Errors.................... 0
Radio Signal Strength Indicator............ -66 dBm
Signal to Noise Ratio...................... 29 dB
Nearby AP Statistics:
APSOEBFF_COR3(slot 0) .....................
antenna0: 50 seconds ago -91 dBm................. antenna1: 50 seconds ago -76 dBm
APSOEAFF_FAC(slot 0) ......................
antenna0: 108 seconds ago -89 dBm................ antenna1: 108 seconds ago -87 dBm
APSOEBGF_FAC(slot 0) ......................
antenna0: 50 seconds ago -82 dBm................. antenna1: 50 seconds ago -71 dBm
APSOEBGF_STAFF(slot 0) ....................
antenna0: 49 seconds ago -74 dBm................. antenna1: 49 seconds ago -58 dBm
WLAN config
WLAN Identifier.................................. 9
Profile Name..................................... STAFF
Network Name (SSID).............................. STAFF
Status........................................... Enabled
MAC Filtering.................................... Enabled
Broadcast SSID................................... Enabled
AAA Policy Override.............................. Disabled
Network Admission Control
NAC-State...................................... Disabled
Quarantine VLAN................................ 0
Number of Active Clients......................... 32
Exclusionlist.................................... Disabled
Session Timeout.................................. Infinity
CHD per WLAN..................................... Disabled
Webauth DHCP exclusion........................... Disabled
Interface........................................ staff
WLAN ACL......................................... unconfigured
DHCP Server...................................... Default
DHCP Address Assignment Required................. Disabled
Quality of Service............................... Silver (best effort)
Scan Defer Priority.............................. 5,6
Scan Defer Time.................................. 100 milliseconds
WMM.............................................. Allowed
Media Stream Multicast-direct.................... Disabled
CCX - AironetIe Support.......................... Enabled
CCX - Gratuitous ProbeResponse (GPR)............. Disabled
CCX - Diagnostics Channel Capability............. Disabled
Dot11-Phone Mode (7920).......................... Disabled
Wired Protocol................................... None
IPv6 Support..................................... Disabled
Peer-to-Peer Blocking Action..................... Disabled
Radio Policy..................................... All
DTIM period for 802.11a radio.................... 1
DTIM period for 802.11b radio.................... 1
Radius Servers
Authentication................................ Disabled
Accounting.................................... Disabled
Dynamic Interface............................. Disabled
Local EAP Authentication......................... Disabled
Security
802.11 Authentication:........................ Open System
Static WEP Keys............................... Disabled
802.1X........................................ Disabled
Wi-Fi Protected Access (WPA/WPA2)............. Disabled
CKIP ......................................... Disabled
Web Based Authentication...................... Disabled
Web-Passthrough............................... Disabled
Conditional Web Redirect...................... Disabled
Splash-Page Web Redirect...................... Disabled
Auto Anchor................................... Disabled
H-REAP Local Switching........................ Disabled
H-REAP Learn IP Address....................... Enabled
Infrastructure MFP protection................. Enabled (Global Infrastructure MFP Disabled)
Client MFP.................................... Optional but inactive (WPA2 not configured)
Tkip MIC Countermeasure Hold-down Timer....... 60
Call Snooping.................................... Disabled
Band Select...................................... Disabled
Load Balancing................................... Disabled
HELPPPP!We have 75 evenly distributed AP's servicing the 500 odd users. Found the below traps on WLC. I was making some changes in the WLAN settings at the time:
Tue Apr 16 00:03:45 2013 Client Excluded: MACAddress:8c:a9:82:5d:d2:dc Base Radio MAC :3c:ce:73:c6:fe:00 Slot: 0 User Name: unknown Ip Address: unknown Reason:802.11 Association failed repeatedly. ReasonCode: 2
106 Tue Apr 16 00:03:45 2013 Client Excluded: MACAddress:58:94:6b:f2:24:c8 Base Radio MAC :c8:f9:f9:4c:01:30 Slot: 1 User Name: unknown Ip Address: unknown Reason:802.11 Association failed repeatedly. ReasonCode: 2
107 Tue Apr 16 00:03:45 2013 Client Excluded: MACAddress:bc:77:37:72:dc:0b Base Radio MAC :3c:ce:73:c6:53:10 Slot: 0 User Name: unknown Ip Address: unknown Reason:802.11 Association failed repeatedly. ReasonCode: 2
108 Tue Apr 16 00:03:45 2013 Client Excluded: MACAddress:00:26:c7:7d:12:76 Base Radio MAC :3c:ce:73:c4:79:80 Slot: 0 User Name: unknown Ip Address: unknown Reason:802.11 Association failed repeatedly. ReasonCode: 2
109 Tue Apr 16 00:03:45 2013 Client Excluded: MACAddress:bc:77:37:75:1f:93 Base Radio MAC :c8:f9:f9:2b:85:30 Slot: 0 User Name: unknown Ip Address: unknown Reason:802.11 Association failed repeatedly. ReasonCode: 2
110 Tue Apr 16 00:03:45 2013 Client Excluded: MACAddress:ac:72:89:58:8e:b9 Base Radio MAC :3c:ce:73:c6:53:10 Slot: 0 User Name: unknown Ip Address: unknown Reason:802.11 Association failed repeatedly. ReasonCode: 2
111 Tue Apr 16 00:03:44 2013 Client Excluded: MACAddress:bc:77:37:26:cd:e3 Base Radio MAC :3c:ce:73:c5:1f:10 Slot: 0 User Name: unknown Ip Address: unknown Reason:802.11 Association failed repeatedly. ReasonCode: 2
112 Tue Apr 16 00:03:44 2013 Client Excluded: MACAddress:ac:72:89:25:ea:e0 Base Radio MAC :3c:ce:73:c6:77:70 Slot: 0 User Name: unknown Ip Address: unknown Reason:802.11 Association failed repeatedly. ReasonCode: 2
113 Tue Apr 16 00:03:44 2013 Client Excluded: MACAddress:00:24:2c:6a:85:3d Base Radio MAC :3c:ce:73:c6:6a:50 Slot: 0 User Name: unknown Ip Address: unknown Reason:802.11 Association failed repeatedly. ReasonCode: 2
114 Tue Apr 16 00:03:44 2013 Client Excluded: MACAddress:68:5d:43:61:16:51 Base Radio MAC :3c:ce:73:f6:0c:20 Slot: 0 User Name: unknown Ip Address: unknown Reason:802.11 Association failed repeatedly. ReasonCode: 2
115 Tue Apr 16 00:03:44 2013 Client Excluded: MACAddress:7c:d1:c3:8a:64:f6 Base Radio MAC :3c:ce:73:c4:74:20 Slot: 1 User Name: unknown Ip Address: unknown Reason:802.11 Association failed repeatedly. ReasonCode: 2 -
WLC 5508 running 7.4.110.0 unable to tftp upload config from controller
Hi,
Two WLC 5508 running identical code version. One is 50 license Primary, the second is HA. Identical config on both. HA WLC can upload its config to the TFTP or FTP server but Primary cannot. The operation fails for both CLI and GUI and for different protocols i.e. TFTP, FTP.
#### Primary Controller
(Cisco Controller) >show sysinfo
Manufacturer's Name.............................. Cisco Systems Inc.
Product Name..................................... Cisco Controller
Product Version.................................. 7.4.110.0
Bootloader Version............................... 1.0.20
Field Recovery Image Version..................... 7.6.95.16
Firmware Version................................. FPGA 1.7, Env 1.8, USB console 2.2
Build Type....................................... DATA + WPS
System Name...................................... PRODWC7309
System Location..................................
System Contact...................................
System ObjectID.................................. 1.3.6.1.4.1.9.1.1069
Redundancy Mode.................................. Disabled
IP Address....................................... 10.1.30.210
Last Reset....................................... Power on reset
System Up Time................................... 18 days 18 hrs 51 mins 35 secs
System Timezone Location......................... (GMT+10:00) Sydney, Melbourne, Canberra
System Stats Realtime Interval................... 5
System Stats Normal Interval..................... 180
Configured Country............................... AU - Australia
Operating Environment............................ Commercial (0 to 40 C)
--More-- or (q)uit
Internal Temp Alarm Limits....................... 0 to 65 C
Internal Temperature............................. +34 C
External Temperature............................. +17 C
Fan Status....................................... OK
State of 802.11b Network......................... Enabled
State of 802.11a Network......................... Enabled
Number of WLANs.................................. 8
Number of Active Clients......................... 138
Memory Current Usage............................. Unknown
Memory Average Usage............................. Unknown
CPU Current Usage................................ Unknown
CPU Average Usage................................ Unknown
Burned-in MAC Address............................ 3C:08:F6:CA:52:20
Power Supply 1................................... Present, OK
Power Supply 2................................... Present, OK
Maximum number of APs supported.................. 50
(Cisco Controller) >debug transfer trace enable
(Cisco Controller) >transfer upload start
Mode............................................. TFTP
TFTP Server IP................................... 10.1.22.2
TFTP Path........................................ /
TFTP Filename.................................... PRODWC7309-tmp.cfg
Data Type........................................ Config File
Encryption....................................... Disabled
*** WARNING: Config File Encryption Disabled ***
Are you sure you want to start? (y/N) Y
*TransferTask: Jun 02 10:41:15.183: Memory overcommit policy changed from 0 to 1
*TransferTask: Jun 02 10:41:15.183: RESULT_STRING: TFTP Config transfer starting.
TFTP Config transfer starting.
*TransferTask: Jun 02 10:41:15.183: RESULT_CODE:1
*TransferTask: Jun 02 10:41:24.309: Locking tftp semaphore, pHost=10.1.22.2 pFilename=/PRODWC7309-tmp.cfg
*TransferTask: Jun 02 10:41:24.393: Semaphore locked, now unlocking, pHost=10.1.22.2 pFilename=/PRODWC7309-tmp.cfg
*TransferTask: Jun 02 10:41:24.393: Semaphore successfully unlocked, pHost=10.1.22.2 pFilename=/PRODWC7309-tmp.cfg
*TransferTask: Jun 02 10:41:24.394: tftp rc=-1, pHost=10.1.22.2 pFilename=/PRODWC7309-tmp.cfg
pLocalFilename=/mnt/application/xml/clis/clifile
*TransferTask: Jun 02 10:41:24.394: RESULT_STRING: % Error: Config file transfer failed - Unknown error - refer to log
*TransferTask: Jun 02 10:41:24.394: RESULT_CODE:12
*TransferTask: Jun 02 10:41:24.394: Memory overcommit policy restored from 1 to 0
% Error: Config file transfer failed - Unknown error - refer to log
(Cisco Controller) >show logging
*TransferTask: Jun 02 10:41:24.393: #UPDATE-3-FILE_OPEN_FAIL: updcode.c:4579 Failed to open file /mnt/application/xml/clis/clifile.
*sshpmReceiveTask: Jun 02 10:41:24.315: #OSAPI-3-MUTEX_FREE_INFO: osapi_sem.c:1087 Sema 0x2b32def8 time=142 ulk=1621944 lk=1621802 Locker(sshpmReceiveTask sshpmrecv.c:1662 pc=0x10b07938) unLocker(sshpmReceiveTask sshpmReceiveTaskEntry:1647 pc=0x10b07938)
-Traceback: 0x10af9500 0x1072517c 0x10b07938 0x12020250 0x12080bfc
*TransferTask: Jun 02 10:39:01.789: #UPDATE-3-FILE_OPEN_FAIL: updcode.c:4579 Failed to open file /mnt/application/xml/clis/clifile.
*sshpmReceiveTask: Jun 02 10:39:01.713: #OSAPI-3-MUTEX_FREE_INFO: osapi_sem.c:1087 Sema 0x2b32def8 time=5598 ulk=1621801 lk=1616203 Locker(sshpmReceiveTask sshpmrecv.c:1662 pc=0x10b07938) unLocker(sshpmReceiveTask sshpmReceiveTaskEntry:1647 pc=0x10b07938)
-Traceback: 0x10af9500 0x1072517c 0x10b07938 0x12020250 0x12080bfc
#### HA Controller
(Cisco Controller) >show sysinfo
Manufacturer's Name.............................. Cisco Systems Inc.
Product Name..................................... Cisco Controller
Product Version.................................. 7.4.110.0
Bootloader Version............................... 1.0.20
Field Recovery Image Version..................... 7.6.95.16
Firmware Version................................. FPGA 1.7, Env 1.8, USB console 2.2
Build Type....................................... DATA + WPS
System Name...................................... PRODWC7310
System Location..................................
System Contact...................................
System ObjectID.................................. 1.3.6.1.4.1.9.1.1069
Redundancy Mode.................................. Disabled
IP Address....................................... 10.1.31.210
Last Reset....................................... Software reset
System Up Time................................... 18 days 19 hrs 1 mins 27 secs
System Timezone Location......................... (GMT+10:00) Sydney, Melbourne, Canberra
System Stats Realtime Interval................... 5
System Stats Normal Interval..................... 180
Configured Country............................... AU - Australia
Operating Environment............................ Commercial (0 to 40 C)
--More-- or (q)uit
Internal Temp Alarm Limits....................... 0 to 65 C
Internal Temperature............................. +34 C
External Temperature............................. +17 C
Fan Status....................................... OK
State of 802.11b Network......................... Enabled
State of 802.11a Network......................... Enabled
Number of WLANs.................................. 4
Number of Active Clients......................... 0
Memory Current Usage............................. Unknown
Memory Average Usage............................. Unknown
CPU Current Usage................................ Unknown
CPU Average Usage................................ Unknown
Burned-in MAC Address............................ 3C:08:F6:CA:53:C0
Power Supply 1................................... Present, OK
Power Supply 2................................... Present, OK
Maximum number of APs supported.................. 500
(Cisco Controller) >debug transfer trace enable
(Cisco Controller) >transfer upload start
Mode............................................. FTP
FTP Server IP.................................... 10.1.22.2
FTP Server Port.................................. 21
FTP Path......................................... /
FTP Filename..................................... 10_1_31_210_140602_1050.cfg
FTP Username..................................... ftpuser
FTP Password..................................... *********
Data Type........................................ Config File
Encryption....................................... Disabled
*** WARNING: Config File Encryption Disabled ***
Are you sure you want to start? (y/N) y
*TransferTask: Jun 02 10:51:31.278: Memory overcommit policy changed from 0 to 1
*TransferTask: Jun 02 10:51:31.278: RESULT_STRING: FTP Config transfer starting.
FTP Config transfer starting.
*TransferTask: Jun 02 10:51:31.278: RESULT_CODE:1
*TransferTask: Jun 02 10:52:05.468: ftp operation returns 0
*TransferTask: Jun 02 10:52:05.477: RESULT_STRING: File transfer operation completed successfully.
*TransferTask: Jun 02 10:52:05.477: RESULT_CODE:11
File transfer operation completed successfully.
Not upgrading to 7.4.121.0 because of bug CSCuo63103. Have not restarted the controller yet.
Any one else had this issue ? Is there a workaround ?
Thanks,
Rick.Thanks Stephen, In my deployments of 7.4.110.0 version I have not seen this issue so may be controller reboot will fix it (we do have HA to minimize the impact). I will keep the thread updated with findings and may request TAC for the special release 7.4.121.0 if the still not happy with 7.4.110.0
Rick. -
2 Cisco WLC 5508 controllers and software upgrade 7.6.130 + FUS 1.9
Hi
I have two WLC 5508 controllers that need 7.6.130 and FUS 1.9 installed. (Current version 7.3 and FUS 1.7)
Configuration: One controller is at Site A and the other controller is at Site B (two different states..)
They're configured so that if Site A goes down, Site A AP's will failover to Site B and vice versa ..
- What would be the recommended approach for upgrading the software to 7.6.130.0 (from 7.3) and also upgrading FUS 1.9 (from 1.7)?
My plan was to download 7.6.130.0 to both controllers and pre-download the software to all AP's (about 100 total between both sites) and then reboot the controllers at night at the same time? Or one before the other?
Step 2. Install FUS 1.9 to each controller.
I'm concerned over what might happen during the upgrade and AP failover etc..
ThanksThis is what I would do:
Upload v7.6.130.0 to all WLCs and then use the pre image download to push the image to all access points.
Dont reboot the wlc
Image swap in the access points so that v7.6.130.0 is primary
Move all access point to one of the WLCs (A)
Enable ap AAA authentication on the WLC that has no access points and the one you will work on first. This prevents access points from joining
Reboot the WLC (A)
Upload the FUS 1.9.0.0
Reboot WLC (A) this takes up to 45 minutes
When the WLC (A) comes back online, uncheck ap AAA authentication
Move access points from WLC (B) to WLC (A)
Enable ap AAA authentication on WLC (B)
Perform all the other task you did earlier on WLC (A)
That's it.
-Scott -
WLC 5508 Internal DHCP server issues
Hi,
I am hoping to get your feedback around the dhcp issues I am facing with Two Centrally Switched Wireless LANs. I have tried to explain the setup and the problems below and would appreciate it if anyone can suggest a solution for the problems I am facing:
The setup is as follows:
- I have a WLC 5508 which has been configured with 4 SSIDs, out of which 2 are using Central Authentication and Switching.
- I have an LWAP connected to the WLC in HREAP mode.
- WLC is configured as the DHCP server for clients connecting to the SSID 'Guest'. For the rest, I am using external dhcp server.
- Only one scope for Guest Interface is setup on the WLC.
Problems:
1. As far as I know, for WLC to act as internal dhcp server, it is mandatory to have the proxy enabled, but the Clients connecting to SSID 'Internet' are
unable to get an ip address from the external dhcp server, if dhcp proxy is enabled on the WLC. If i disable the proxy, it all works fine.
2. DHCP does not release the ip addresses assigned to clients even after they are logged out.
3. If a machine which was earlier connected to 'Guest' SSID connects to the 'Internet' SSID, it requests the same ip it was assigned by the WLC which it was assigned under 'Guest', but gets tagged with the Vlan configured on the management interface.
************Output from the Controller********************
(Cisco Controller) >show sysinfo
Manufacturer's Name.............................. Cisco Systems Inc.
Product Name..................................... Cisco Controller
Product Version.................................. 7.0.116.0
Bootloader Version............................... 1.0.1
Field Recovery Image Version..................... 6.0.182.0
Firmware Version................................. FPGA 1.3, Env 1.6, USB console 1.27
Build Type....................................... DATA + WPS + LDPE
(Cisco Controller) >show interface summary
Interface Name Port Vlan Id IP Address Type Ap Mgr Gu
est
guest 1 301 10.255.255.30 Dynamic No No
management 1 100 172.17.1.30 Static Yes No
service-port N/A N/A 192.168.0.1 Static No No
virtual N/A N/A 10.0.0.1 Static No No
(Cisco Controller) >show wlan summary
Number of WLANs.................................. 4
WLAN ID WLAN Profile Name / SSID Status Interface Name
1 LAN Enabled management
2 Internet Enabled management
3 Managment Assets Enabled management
4 Guest Enabled guest
(Cisco Controller) >show dhcp detailed guest
Scope: guest
Enabled.......................................... Yes
Lease Time....................................... 86400 (1 day )
Pool Start....................................... 10.255.255.31
Pool End......................................... 10.255.255.254
Network.......................................... 10.255.255.0
Netmask.......................................... 255.255.255.0
Default Routers.................................. 10.255.255.1 0.0.0.0 0.0.0.0
DNS Domain.......................................
DNS.............................................. 8.8.8.8 8.8.4.4 0.0.0.0
Netbios Name Servers............................. 0.0.0.0 0.0.0.0 0.0.0.0
(Cisco Controller) >show interface detailed management
Interface Name................................... management
MAC Address...................................... e8:b7:48:9b:84:20
IP Address....................................... 172.17.1.30
IP Netmask....................................... 255.255.255.0
IP Gateway....................................... 172.17.1.1
External NAT IP State............................ Disabled
External NAT IP Address.......................... 0.0.0.0
VLAN............................................. 100
Quarantine-vlan.................................. 0
Active Physical Port............................. 1
Primary Physical Port............................ 1
Backup Physical Port............................. Unconfigured
Primary DHCP Server.............................. 172.30.50.1
Secondary DHCP Server............................ Unconfigured
DHCP Option 82................................... Disabled
ACL.............................................. Unconfigured
AP Manager....................................... Yes
Guest Interface.................................. No
L2 Multicast..................................... Enabled
(Cisco Controller) >show interface detailed guest
Interface Name................................... guest
MAC Address...................................... e8:b7:48:9b:84:24
IP Address....................................... 10.255.255.30
IP Netmask....................................... 255.255.255.0
IP Gateway....................................... 10.255.255.1
External NAT IP State............................ Disabled
External NAT IP Address.......................... 0.0.0.0
VLAN............................................. 301
Quarantine-vlan.................................. 0
Active Physical Port............................. 1
Primary Physical Port............................ 1
Backup Physical Port............................. Unconfigured
Primary DHCP Server.............................. Unconfigured
Secondary DHCP Server............................ Unconfigured
DHCP Option 82................................... Disabled
ACL.............................................. Unconfigured
AP Manager....................................... No
Guest Interface.................................. No
L2 Multicast..................................... Enabled
(Cisco Controller) >show dhcp leases
MAC IP Lease Time Remaining
00:21:6a:9c:03:04 10.255.255.46 23 hours 52 minutes 42 seconds <<<<<<< lease remains even when the client is disconnected.
*********Example of Client connected to the right Vlan with an ip address from the incorrect interface. *************
(Cisco Controller) >show client detail 00:21:6a:9c:03:04
Client MAC Address............................... 00:21:6a:9c:03:04
Client Username ................................. N/A
AP MAC Address................................... a0:cf:5b:00:49:c0
AP Name.......................................... mel
Client State..................................... Associated
Client NAC OOB State............................. Access
Wireless LAN Id.................................. 2 <<<<<<<< 'Internet' SSID
BSSID............................................ a0:cf:5b:00:49:ce
Connected For ................................... 319 secs
Channel.......................................... 36
IP Address....................................... 10.255.255.46 <<<<<<< IP address assigned from the 'Guest' Interface or dhcp scope on the WLC
Association Id................................... 1
Authentication Algorithm......................... Open System
Reason Code...................................... 1
Status Code...................................... 0
Session Timeout.................................. 1800
Client CCX version............................... 4
Client E2E version............................... 1
QoS Level........................................ Silver
802.1P Priority Tag.............................. disabled
WMM Support...................................... Enabled
Power Save....................................... OFF
Mobility State................................... Local
Mobility Move Count.............................. 0
Security Policy Completed........................ Yes
Policy Manager State............................. RUN
Policy Manager Rule Created...................... Yes
ACL Name......................................... none
ACL Applied Status............................... Unavailable
Policy Type...................................... N/A
Encryption Cipher................................ None
Management Frame Protection...................... No
EAP Type......................................... Unknown
H-REAP Data Switching............................ Central <<<<<<<<<
H-REAP Authentication............................ Central <<<<<<<<<<
Interface........................................ management
VLAN............................................. 100 <<<<<<<<<<< right Vlan
Quarantine VLAN.................................. 0
Access VLAN...................................... 100Hi All,
I have a similar issue where Wireless clients are not receiving automatic addressing from an internal DHCP server. I have multiple interfaces configured on the WLC which are connected to separate VLANS. The manually specified DHCP primary server entry is the same on all interfaces. Some clients are able to authenticate and receive automatic IP configuration but some clients are failing the address assignment process. I have checked connectivity between the WLC and DHCP server, this is confirmed as working. When I carry out a "debug dhcp packet enable", I get the following outputs which seems as if the DHCP discover request from the client is skipped. Your thoughts and inputs on this are appreciated.
DHCP Socket Task: Nov 07 11:16:09.174: 00:22:fb:7b:37:32 DHCP option len (including the magic cookie) 76
*DHCP Socket Task: Nov 07 11:16:09.174: 00:22:fb:7b:37:32 DHCP option: message type = DHCP DISCOVER
*DHCP Socket Task: Nov 07 11:16:09.174: 00:22:fb:7b:37:32 DHCP option: 116 (len 1) - skipping
*DHCP Socket Task: Nov 07 11:16:09.174: 00:22:fb:7b:37:32 DHCP option: 61 (len 7) - skipping
*DHCP Socket Task: Nov 07 11:16:09.174: 00:22:fb:7b:37:32 DHCP option: requested ip = 169.254.223.5
*DHCP Socket Task: Nov 07 11:16:09.174: 00:22:fb:7b:37:32 DHCP option: 12 (len 13) - skipping
*DHCP Socket Task: Nov 07 11:16:09.174: 00:22:fb:7b:37:32 DHCP option: vendor class id = MSFT 5.0 (len 8)
*DHCP Socket Task: Nov 07 11:16:09.174: 00:22:fb:7b:37:32 DHCP option: 55 (len 11) - skipping
*DHCP Socket Task: Nov 07 11:16:09.174: 00:22:fb:7b:37:32 DHCP option: 43 (len 2) - skipping
*DHCP Socket Task: Nov 07 11:16:09.174: 00:22:fb:7b:37:32 DHCP options end, len 76, actual 68
*DHCP Socket Task: Nov 07 11:16:09.174: 00:22:fb:7b:37:32 DHCP Forwarding DHCP packet (332 octets) packet DHCP Socket Task: Nov 07 11:16:09.174: 00:22:fb:7b:37:32 DHCP option len (including the magic cookie) 76
Thanks,
Raj Sandhu -
WLC 5508 HA Problem Soft.ver 7.4.100
Dear Support,
we are using two WLC 5508 software ver.7.4.100 with first 50AP license and in the next day we add 50AP license again to the primary WLC. when we activate HA base in the following guiden http://www.cisco.com/c/en/us/td/docs/wireless/controller/technotes/7-5/High_Availability_DG.html but when we doing test the failover we found a couple log message on the Secondary WLC like below and not for long time all AP on the Secondary WLC was drop off.
1. DP Critical Error
2. *RRM-DCLNT-2_4: May 23 07:43:53.204: #RRM-3-RRM_LOGMSG: rrmTables.c:682 RRM LOG: Could not retrieve RRM Coverage Measurement DataKey BSSID:34:db:fd:dd:3e:20,Key SlotId:0
*RRM-DCLNT-2_4: May 23 07:43:53.164: #RRM-3-RRM_LOGMSG: rrmTables.c:682 RRM LOG: Could not retrieve RRM Coverage Measurement DataKey BSSID:34:db:fd:dd:3e:20,Key SlotId:0
*RRM-DCLNT-2_4: May 23 07:43:52.854: #RRM-3-RRM_LOGMSG: rrmTables.c:682 RRM LOG: Could not retrieve RRM Coverage Measurement DataKey BSSID:2c:36:f8:72:fc:c0,Key SlotId:0
I also send a complete log for both problem above and enclose it with pdf file. need you advice and assistance,
regard, afriansyahI agree go to version 7.4.121.0 I has some strange issues on prior releases. Personally I am running 7.6.120.0 right now but that's mainly due to support for the 3702 access points.
http://www.cisco.com/c/en/us/td/docs/wireless/controller/technotes/7-5/High_Availability_DG.html#pgfId-74573
that's a good guide just to double check yourself just in case. - -
Upgrade WLC 5508 Ver. 7.0.98.0 to Ver 7.6.110.0
i will upgrade WLC 5508 Ver 7.0.98.0 with License 50 AP. to Ver 7.6.110.0 will it ask to install license ?
No, It will not ask for again.
Just upgrade the software.
Regards
Dont forget to rate helpful posts -
WLC 5508 7.3.112.0 System Crash
hi i got this situation.
model : wlc 5508
verstion : 7.3.112.0
our controllers working WLC1-active, WLC2-active, suddenly WLC1 went down and up (two times).
and normally working now. I cant figure out.
crash info
==============================================================================
Number of files present is: 5
Beginning of Crash File: mwar_dump2.crash
Dumping registers
CPU Registers:
$ 0 : 00000000 1000cce1 00000002 00000000
$ 4 : ffffffff 00000001 00000001 00000000
$ 8 : 00000000 12800f70 12800f70 4b263328
$12 : 00000000 80000010 8117d240 10a1cfa8
$16 : 481596f8 4b263350 00000001 00000005
$20 : 4b263328 4b26332c 00010000 00000000
$24 : 00000070 11d53520
$28 : 131d1ce8 4b2632f0 1013c078 1013cb58
Hi : 0000001f
Lo : 33333362
Stack :
00000000 00000001 00000000 48159848
00000000 00000001 00000000 00000000
00000004 00000000 000001a7 00000001
4b4520f1 00000002 00000004 0025a6b5
315ebc72 b1d6aebd 010d0000 00000000
00000000 00000000 48159848 481597e0
481598b0 48159918 48159980 481599e8
48159a50 48159ab8 48159b20 48159b88
48159bf0 48159c58 48159cc0 48159d28
48159d90 48159df8 00000000 3381c438
00000000 00000001 00000003 4b263320
13201ce8 131f1ce8 131e1ce8 131d1ce8
131f1ce8 131d1ce8 131e1ce8 131d1ce8
13201ce8 131d1ce8 00000000 d8a5a096
00000000 481596f8 00000000 00000001
00000000 14114854 00000000 4b263a5c
* Start Cisco Crash Handler *
Sys Name: Controller#1
Model: AIR-CT5508-K9
Version: 7.3.112.0
Timestamp: Tue Jan 28 20:43:09 2014
SystemUpTime: 351 days 19 hrs 6 mins 8 secs
signal: 11
pid: 1075
TID: 1260798800
Task Name: apfRogueTask_3
Reason: System Crash
si_signo: 11
si_errno: 0
si_code: 1
si_addr: 0x779
timer tcb: 0xa1f
timer cb: 0x10588ab0 ('rrmTimerInit+592')
timer arg1: 0x1bbd0530
timer arg2: 0x0
Long time taken timer call back inforamtion:
Time Stamp: Tue Jan 28 20:43:09 2014
timer cb : 10588ab0p('rrmTimerInit+592')
Duration : 768804 usecs, cbCount= 2
Analysis of Failure:
Software Failed on instruction at :
pc = 0x1013cc14 (DebugPrintRogueRRMneighbor+8480), ra = 0x1013cb58 (DebugPrintRogueRRMneighbor+8480)
Software Failed while accessing the data located at :0x779
=============================================================================
anyone can know about failed reason? now we processing in rma. we going to change hardware 5days away.Hi
Only Cisco TAC can analysis this & tells you exact reason of this reload. It looks like a software related crash..
I would suggest to move onto a later code (like 7.4.121.0) rather staying in 7.3 code when you get the new hardware.
HTH
Rasika
**** Pls rate all useful responses **** -
WLC 5508 in HA pair (7.4.121.0) sudden reload
I have a pair of WLC 5508 in HA pair running version 7.4.121.0, last week I have two sudden reload on my active WLC. Here's the error from my syslog server on the first sudden reload. The second reload has almost the same logs.
10.x.x.234 - active
10.x.x.237 - standby
2014-01-30 17:52:20 Local0.Error 10.x.x.237 WLC-HA01: *rmgrMain: Jan 30 17:52:24.498: #RMGR-3-RED_HEARTBEAT_TMOUT: rmgr_main.c:242 rmgrTmoHeartbeat: Recved GW ping count 6 phyMgr ping count 0.
2014-01-30 17:52:20 Local0.Emerg 10.x.x.237 WLC-HA01: *rmgrMain: Jan 30 17:52:24.555: #RMGR-0-RED_HA_RELOAD: rmgr_utils.c:198 System reboot: reason: category Sanity check object Self
2014-01-30 17:52:21 Local0.Emerg 10.x.x.234 WLC-HA01: *rmgrMain: Jan 30 17:52:24.989: #RMGR-0-RED_HA_RELOAD: rmgr_utils.c:188 System reboot: reason: category Peer reload req object Peer
2014-01-30 17:52:21 Local0.Alert 10.x.x.234 WLC-HA01: *dtlArpTask: Jan 30 17:52:25.106: #DTL-1-IP_CONFLICT_DETECTED: dtl_net.c:4857 Network device with mac addr 7c:ad:74:8d:6b:0f using IP address of local interface
Cisco TAC recommends to disable monitoring the default gateway.
--> config redundancy management-gateway-failover disable
I was wondering if someone has the issue with what I have.
Second issue I have is when it fails over to the standby WLC, I do get a web-auth certificate error from the WLC when clients login. This only happens after a sudden reload. If I do a redundancy force-switchover during maintenance window, the certificate error doesn't show up. To fix the certificate error I have to bounce both WLCs one after the other.
Thanks in advance.Hi,
I exeprienced a reload problem in standby WLC, with HA in release 7.6.100.0.
I use a dedicated VLAN to transport the redundancy sync and info, 'cause the two WLCs are in different buildings.
The standby WLC reload continuously 'cause it doesn,t find the default gateway.
(Cisco Controller-Standby) >show redundancy summary
Redundancy Mode = SSO ENABLED
Local State = STANDBY HOT
Peer State = ACTIVE
Unit = Secondary - HA SKU (Inherited AP License Count = 500)
Unit ID = 00:06:F6:DB:E3:E0
Redundancy State = SSO (Both AP and Client SSO)
Mobility MAC = 58:8D:09:CD:81:C0
Management Gateway Failover = ENABLED (Management GW failover would be operational in few moments)
Average Redundancy Peer Reachability Latency = 621 usecs
Average Management Gateway Reachability Latency = 0 usecs
Redundancy Management IP Address................. 40.231.36.6
Peer Redundancy Management IP Address............ 40.231.36.5
Redundancy Port IP Address....................... 169.254.36.6
Peer Redundancy Port IP Address.................. 169.254.36.5
Rebooting as default GW is not reachable from Standby Controller
Restarting system. Reason: Default Gateway is not reachable ..
The problem is that the WLC tries to ping the DGW using the primary IP management address belonging to the active WLC, so we have duplicated IP problem, ARP problem and so on .....
The standby WLC should use the redundancy managemet address to ping the default gateway, instead the primary IP management address!!!!!!
So the workaround is the CLI command :
config redundancy management-gateway-failover disable
on the primary WLC, via console or in SSH.
When the standby will reload it will inherit the config from the active primary WLC
(Cisco Controller-Standby) >show redundancy summary
Redundancy Mode = SSO ENABLED
Local State = STANDBY HOT
Peer State = ACTIVE
Unit = Secondary - HA SKU (Inherited AP License Count = 500)
Unit ID = 00:06:F6:DB:E3:E0
Redundancy State = SSO (Both AP and Client SSO)
Mobility MAC = 58:8D:09:CD:81:C0
Management Gateway Failover = ENABLED (Management GW failover is disabled as it is DISABLED on the Peer)
Average Redundancy Peer Reachability Latency = 666 usecs
Average Management Gateway Reachability Latency = 0 usecs
Redundancy Management IP Address................. 40.231.36.6
Peer Redundancy Management IP Address............ 40.231.36.5
Redundancy Port IP Address....................... 169.254.36.6
Peer Redundancy Port IP Address.................. 169.254.36.5
The workaround works in my experience.
Maybe you are looking for
-
I have tried clearing my cache but this hasnt made any difference. I haven't made any changes to my settings. The posts simply dont appear on my timeline or in my activity log. A few of my friends had the same problem and have had to downgrade to an
-
Skype crashes when clicking a contact (External ex...
Hi Skype Community, So this issue appeared suddenly upon booting my computer today. I can login to Skype and it opens normally as it would, but whenever I click on any contact, it promptly freezes, gives me the generic "Skype has stopped working" err
-
P20-102 Satellite - Remote Receiver not working after running recovery CD
Hi, I'm running Windows Media Center Edition and on my P20-102 Satellite notebook. I recently needed to run the recovery CD, the process went fine except that my external remote receiver box supplied with my notebook no longer works. The box was work
-
Several months ago, I installed LR5 as an upgrade to LR4. About a week ago, I started using LR5. For the first few days all went well and I imported about a thousand pix. The next time I sat down to import more pix, the LR5 Import module couldn't see
-
sorry, seems my title is a little long, says it all though, cant boot from usb, cant boot from disc, any thoughts? need my mac bac!!!