Wlc 5508: windows 8 can't connect using wpa+wpa2

Dear All,
I need your help.
My customer have Cisco WLC 5508 (cisco wlc 7.0.116.0) .
We create ssid with layer 2 security wpa+wpa2.
Using Windows 8, it's can't connect to the wireless lan.
But if I change, the ssid, with layer 2 security wep.
It can connect / connected.
Please help.
Thanks,
Jerri

This is a known issue with Windows 8. You need to upgrade your firmware to 7.0.250.X for wireless clients running Win8.
Another thing, choose one: Either WPA or WPA2. Don't enable one and "hope" the wireless client will make the choice because most of the time, they won't.

Similar Messages

IOS 5 can't connect to WPA/WPA2 Enterprise Wireless Network

After upgrading multiple iPhone 4 (CDMA versions) to IOS 5.0, I have not been able to get them to connect to our WPA/WPA2 Enterprise wirless network. We use a Cisco Wireless LAN Controller. The wireless network is capable of doing WPA or WPA2 Enterprise with PEAP. These phones all connected to this network fine before the upgrade.
When connecteding to the network, it prompts me for the username and password and when I tap join it sits for about 10-15 seconds then says "Unable to join the network" with a Dismiss button.
It connects to non-Enterprise networks just fine. I have tested it on WPA Personal and WPA2 Personal networks and it has worked on several without issue.
I have tried "forget this network" with no success.
Is anyone else having this problem? I know of at least three Verizon iPhone 4's that have this exact same problem. I haven't seen one working with this configuration yet.

I have the same problem:
Cisco WLC's -> WPA2 Enterprise AES + EAP-PEAP 802.1x with CCKM
Pre 5.0 - all worked fine
Post 5.0 - it tries to connect and after few moments i get error - couldn't connect.
Info from controller:
10/17/2011 12:16:37 CEST           INFO           172.16.16.X           Sending EAP request to client from radius server. 6.f. ..l
10/17/2011 12:16:38 CEST           ERROR           172.16.16.X           Retransmitting EAP-ID request to client,retransmission timer expired. 5.y. ..l
10/17/2011 12:16:39 CEST           ERROR           172.16.16.X           Retransmitting EAP-ID request to client,retransmission timer expired. 5.y. ..l
10/17/2011 12:16:40 CEST           ERROR           172.16.16.X           Authentication failed for client as EAP ID request from AP reached maxmium retransmissions. 5.yp ..l
10/17/2011 12:16:40 CEST           ERROR           172.16.16.X           De-authentication sent to client. 5.oP ..l
10/17/2011 12:16:40 CEST           ERROR           172.16.16.X           5.yp ..l
10/17/2011 12:16:40 CEST           ERROR           172.16.16.X           EAPOL-key is invalid, scheduling client for deletion. 5.yp ..l
On the Radius server i don't see any activity regarding this device.
I had this network configured on my iPhone - after upgrade and restore it remembered it. Every time i was in vicinity of my Enterprise WLAN it tried to connect - resulting int express battery drain - 6-7 hrs and battery was empty from 100%

MacOSX 10.3.8 system with original Airport card can't connect via WPA/WPA2

Hi all,
My WiFi network consists of an Airport Express running a WPA/WPA2 Personal network and 802.11b/g compatibility, upon which 3 Macs (all with Airport Extreme/G or /Draft-N cards) and 2 PCs (both G compatible) merrily connect to.
I have an old PowerMac G4 which I've just fitted with an original non-Extreme Airport card, and having updated MacOSX 10.3.8 with Airport 4.2 to enable WPA access, it still refuses to connect to the network; I get the "There was an error joining the Airport network ..." when the correct password is entered.
My understanding is that while the old Airport cards don't support WPA2, they do support WPA and thus if the Airport Express network is set to WPA/WPA2 and b/g compatibility (which I'm assuming is some kind of all encompassing compatibility mode, given there's also sole WPA2 options) then it shouldn't have any problems connecting to the network. What am I missing here?
Cheers, Ben.

I am having the exact same problem. Powerbook G4; original factory installed airport card; with Panther 10.3.9 OS plus updated 4.2 Airport Admin. Utility. It will NOT connect to my Airport Express set to the WPA/WPA2, which is working fine with my iPod touch.
When I get to the screen requesting password for my chosen airport network ("Wireless Security: WPA Personal), the "OK" button is grayed out and it will not even let me submit a password to connect. Can somebody help?

Windows laptops can't connect to Macbook Pro shared internet when WEP security is on

As the title states, my Windows laptops can't connect to Macbook Pro shared internet when WEP security is on. My iPhone has no problem asking for the password when I try to access the shared internet my MacBook Pro on Mountain Lion is sending, but my Samsung Slate on Windows 8 sees the network and only succeeds in connecting when no password is required. When security is on, it just tries for a moment and says it can't connect to the network without ever prompting me for the password. The same thing occurs on my Asus Netbook running Windows XP. Since all the reviews about OS X's internet sharing mentions "any wifi device" can access it, I haven't assumed it's only compatible with Apple products. I want my MacBook Pro to save me from needing an external router.

I would post a new question, outline the specific problem you are having and skip all the extra. Outline any steps you have taken already to try and solve the problem. Post the question in the forum most likely to have followers who can answer your question. Give your topic a good title such as: My MacBook Pro cannot connect to my WEP-enabled PC.
Provide any hardware information that may be relevant such as the make and model of your router and method of connection - wired or wireless.
I'm no authority, but have you tried using WPA2/Personal on your PCs? This method is most compatible with Macs.
If the WEP password is a hexadecimal password then on the Mac you need to preceed the number with a $ sign or the hex digits, 0x.
These links may be useful:
AirPort- Joining an encrypted WEP or WPA Wi-Fi network
AirPort Express- Difficulty joining 3rd-party network that is using WEP

Windows 8 can not connect RemoteApp on W2K12 RDS, but Windows 7 can connect. Why?

Hi!
Windows 8 can not connect RemoteApp (W2K12 RDS), but Windows 7 can connect. Why?
External and internal DNS name is different, the public Cert is mapped to RD Web Access and a RD GateWay Role.
The internal cert (issued by enterprise ca) is mapped to RD Connection Broker roles (SSO and Publishing).
These certifications also be installed on client computers (Personal and Trusted Root Certification Authorities).
The internal CA revocation list is publicated to a website and this web site is accessible from internet. Ports (3389,3391,443) forwarded to RDS server.
On windows 7 everything works fine, but Windows 8 can not connect to Remote Apps. Windows 8 can connect to RDS server via Remote Desktop Connection.
The error:
Thank you for your answers.

Check this thread ->
http://social.technet.microsoft.com/Forums/windowsserver/en-US/0c0d7c4a-e422-4a6c-99eb-66df26a1ffc6/rdp8-your-computer-cant-connect-to-the-remote-computer-because-an-error-occurred?forum=winserverTS
and this
http://support.microsoft.com/kb/2903333
HTH,
JB

HT1899 I have Lion 10.7. To install Windows 7 can I just use MozyHome 6.2.1.515, or do I really need a CD or DVD disc? Do I have to purchase anything (licensed) Windows from Microsoft?

Friday 18 May, 2012 6:35 PM (Atlantic Time)
I have Lion 10.7. To install Windows 7 can I just use MozyHome 6.2.1.515, or do I really need a separate CD or DVD disc? Do I have to purchase anything (licensed) Windows from Microsoft?
Thanks, anybody.
Sincerely,
Steven L.Hamilton, M.D.
Halifax CANADA

Microsoft is not in the business of giving software away for free, they sell it instead.
Buy a copy of Windows 7 Home premium or Professional, then install it using the method of your choice.

MacBook Pro Can't connect to WPA protected network

Just got my new MBP this week. I am in love with it but I have this problem, I can't connect to WPA network, every time I try to connect and type the WPA password it take time and then comes back with "There was an error joining the AirPort network "Intersys"
I removed the WPA from the router and try to connect and it work fine. Change to WPA and no connections.
any suggestions? Thanks in advance

I was actually logging into the forums for this exact reason.
I bought a new router ( Linksys http://tinyurl.com/fkrt9 )last night and wanted to set up WPA/WPA2 encryption on it.
My choices after that we AES and TKIP. I know more about AES so I selected that and set up my key.
Well after that I got the same error that you got. SO I went back and selected TKIP instead and I've been able to conenct, I'm also using 64 character key.
I would still like to use AES, but for now I'm happy with TKIP.
For more info:
TKIP http://en.wikipedia.org/wiki/TKIP
WPA http://en.wikipedia.org/wiki/Wi-FiProtectedAccess
MBP Mac OS X (10.4.4)

HT4718 would i be able to use the lion internet recovery since my college uses WPA/WPA2 Enterprise wifi?

would i be able to use the lion internet recovery since my college uses WPA/WPA2 Enterprise wifi? Im confused becasue this exact one is not listed under apples page about os x recovery.

Probably not. You'd need to go somewhere that Internet isn't on a locked-down wireless network.
See this for specifics. "It depends."
http://support.apple.com/kb/HT4718

VPN to a Windows Network - can't connect to server using RDC

I'm trying to connect to my office's windows network.
I can connect using Cisco VPN but can't when I try to Connect to Server when specifying AFP or SMB as the path. I was told SMB is not supported and that I should just be able to use RDC once the VPN is established. RDC however is not connecting for me either. Any suggestions are greatly appreciated. Thnx

Check your System Preference settings under sharing,
if your firewall is on it may cause issues. Turn it
off and see if that solves it for you. If not make
sure you're using the latest client (4.9).
Hi. Problem occurs with and without firewall on. I'm using Cisco VPN 4.9 too. I've been able to use RDC before which is weird. I'm not sure, but ever since the last Apple Security Update last week...I have been having this problem. But I'm not ruling out anything the IT dept. may be doing. :\

WLC 5508 & Windows Server 2008 radius

Hello guys, I need some bailout here. I have a WLC 5508 which i have configured for AP's but i would like to use the windows server 2008 as the radius server to authenticate the Active directory users.
Can i use a separate windows server 2008 as the radius server or I have to use the same server working as the Active directory?
I don't want to request unnecessary server from my client.
Rgds,
Anthony

I am trying to take my WLC 5508 and have backend authentication through LDAP using web auth. i have tried and tried to set this up but it fails everytime.
http://www.cisco.com/en/US/tech/tk722/tk809/technologies_configuration_example09186a008067489f.shtml
I used that document to get me most of the way there but i cant get the part in the WLC where i go to SECURITY>AAA>LDAP, from here i click on the SERVER index that I want to use which is 1 and not sure what creditenals to put in some of those fields on there. the fields are USER BASE DN: , USER ATTRIBUTE: , and USER OBJECT TYPE: . I have tried to do it as the link says from above but it just does not work.

WLC 5508 disable wlan client still connected

I have one wlc 5508 running on latest IOS 7.116, there is one wlan abc which i have disable status and disable broadcast, but randomly still i can see from wlc dashboard there is one client connected to this wlan abc. The moment i check on the client details, there is no client connected to that wlan and when return to dashboard, no more client connected to that wlan abc. This happened in randomly, it is bug or something else?

I would guess that the client entry also indicates "probing" as status. It means that the client is not connected. It is actually probing, so it"s looking for that SSID that it probably associated to in the past (so it remembers about it)

Can't connect using SMB, but can with CIFS

I'm trying to connect to a windows share from my PB running tiger. I can connect fine in finder going 'Network/Workgroup/PC_Name/' but if I us the 'Go > connect to server' in finder I cannot.
I click go, connect to server and type "//192.168.0.3/My Documents/' it says cannot find sever. Same if is use the smb prefix.
When I get info on the share it says CIFS://WORKGROUP;MARK@PC_NAME/My Documents/
so I can't understand why I cant connect using SMB, I've checked directory access and SMB is enabled, workgroup is set. I know I've been able to connect via SMB before, not sure why I can't now?

For the longest time I have had an Alias of all my remote PC servers in the Dock. One click and I'm connected. As of 10.4.5 those Alias' no longer work. When I click on them instead of getting the volume mounted and ready, I get a the login window with the Workgroup and User Name asking for the password that should be in the Keychain. I enter the password and click connect and get nothing. No errors, no pings, just the Network icon in the Dock turns into a ?.
I go to the Network Browser and the servers show up in their proper workgroups. I click the server, get the login window, put in the password and get an error that the "Server" could not be opened, because the original item cannot be found. With three buttons "Delete Alias", Fix Alias", and "OK". If it can't be found, then what is it showing me in the browser?
I have 10.4.4 on another partition for emergency backup use in the event 10.4.5 fails (and it is). I went to 10.4.4 and all works just fine. All this started in 10.4.5.
G4 FW800 Mac OS X (10.4.5) Totally Stuffed/Max'd Out with lots of great toys.

Solution for Windows 7 can not connect to Time Capsule Guest network

Problem: Sony Vaio running Windows 7 (64bit) will not connect to my Time Capsule Guest network
For added security, I set up a guest network at home. My friend brought over a Vaio and was unable to get an internet connection via my Guest network. The Vaio connected to the Time Capsule with no problem, with full bars, but was not able to get on the internet.
After way too many hours going through useless online suggestions and even calling Apple tech support to see if there might be a known compatibility issue (where I was told they had no idea and I should call Mr Softy) I discovered that the Vaio had somehow set itself to use the DNS Server address of the Time Capsule, main network, not the guest network. (ie Main network uses 10.1...., Guest uses 172.1....) so once I set the Vaio to Obtain DNS server address automatically it fixed the problem and connected to the internet via the Guest network.
Detailed solution:
Configure Time Capsule Guest as follows:
Network Name: fill in the blank
Allow Guest Network to communicate: left unchecked
Guest Network Security: WPA/WPA2 Personal
Password: fill in the blank
Configure Vaio:
Set up new connection from the Network and Sharing center using the name given to Guest network
(for password chose WPA2-Personal>AES>then your Guest Password)
Select Manage wireless networks from left column in main Network and Sharing center window
Select Adapter Properties
Click on Internet Protocol Version 4 (TCP/IPv4) to highlight it, and Select Properties
Make sure both Obtain an IP address automatically and Obtain DNS server address automatically are selected then OK & go back to Network and Sharing center
Connection is active.
Hope this helps those condemned to playing system admin for their windows brethren

Great post!
Here are a couple of more methods to add to your bag of tricks:
Method #1: Use Win7's built-in diagnostics to remedy network maladies
• Start > Start Search > type in: ncpa.cpl <Enter>
• Select current active connection.
• Click Diagnose this connection
• Select Reset the network adapter
Method #2: Use the ipconfig tool to renew the DHCP-provided IP address information
• Start, then click Run, and then, type: cmd, and then, press <enter>
• At the prompt, enter the following commands; press <enter> after entering each one:
ipconfig /release
ipconfig /renew

E3000 - WVC210 Cam - Can't Connect Using IP Address

I've searched here and on portforward.com and have read all FAQ's for a solution to my problem with now luck. Prior to contacting Tech Support via telephone thought that I'd try a post here first.
I've had a Linksys WVC54GCA IP Camera running through my E3000 wireless router with zero issues for quite some time. I just added a Cisco WVC210 PTZ IP Cam. My setup went flawlessly and both cameras are operatng independently of one and other and I am able to view both cameras using my DYNDNS.com supplied Web Host URL's away from home and both camera's are working great on my iPhone 3GS.
I have assigned fixed IP addresses to both camera's. 192.168.1.200 for the the WVC54GCA and 192.168.1.201 for the WVC210. I have setup the Port Range Forward as follows:
Cam1 80 to 80 Both 192.168.200
Cam1 1024 to 1024 Both 192.168.1.200
Cam2 1025 to 1025 Both 192.168.1.201
Here's the thing I don't understand. Again, both cams do what they're supposed to, except; on my home network I can connect directly to the older WVC54GCA using its 192.168.1.200 fixed ip address. I CAN NOT connect directly to the new WVC210 using its fixed ip address of 192.168.1.201. I get an IE error.
I have a feeling that there's something I'm not doing on the router or it has something to do with being on port 1025. Any help would be greatly appreciated.

I don't think there is any issue with the port 1025 for the second camera.
The port 1025 will be used to see the camera from outside.
If you are able to see both the cameras from out side that means both the cameras are configured properly and working fine.
What error message do you get when you try to see the camera using the IP address of the camera?
Try using another browser and check if you can see the camera in the network.
Try to ping the IP address of the camera. if you get replies from the camera IP address then your computer is able to communicate with the camera.
What is the operating system on your computer?

My iMac 5.1 with Windows XP can't connect with Time Capsule

The iMac can connect with Mac OS but not with Win XP.
Can see the signal, but can't connect.

The TC uses names that are not SMB compatible by default.
Change all names.. TC itself and wireless if you use it to short.. no spaces.. pure alphanumeric.
Use WPA2 Personal security with passkey of 8-12 characters and same rules.. no spaces pure alphanumeric.

Wlc 5508: windows 8 can't connect using wpa+wpa2

Similar Messages

Maybe you are looking for