WLC 5508 with version 7.0.98.0 and AIR-LAP1242ag

hi, recently i have deployed wlc 5508 with ap 1262. initially i had trouble with the existing version on the wlc (6..0.199.0) which AIR-LAP1262N-E-K9 was not registering with wlc. i have upgraded the wlc to 6.0.199.4 ver still it was not registering. finally i have upgraded to 7.0.98.0 and all the 40 AP's ( AIR-LAP1262N-E-K9 ) are addedd and its working fine.
Now my issue is, at the same site i have 12 nos of AIR-LAP1242ag autnomous AP's which i need to convert to lightweight ap and register with wlc. where i am stuck currently. after loading the recovery image (c1240-rcvk9w8-tar.123-7.JX9.tar) the ap reboots and can see it register with wlc within seconds contollers pushed the new image and once the ap reboots, never register again.
does anyone has any idea?

After adding the country codes GB and RU.. in my test setup 1242 is registered...i will have it run for couple hours and see the result
ref: below
(Cisco Controller) >show ap uptime
Number of APs.................................... 2
Global AP User Name.............................. Not Configured
Global AP Dot1x User Name........................ Not Configured
AP Name              Ethernet MAC       AP Up Time               Association Up Time
AP1cdf.0f66.79ca     1c:df:0f:66:79:ca 0 days, 00 h 43 m 35 s   0 days, 00 h 42 m 36 s
AP001e.be27.a7e6     00:1e:be:27:a7:e6 0 days, 00 h 16 m 56 s   0 days, 00 h 07 m 15
This issue sorted...thanks

Similar Messages

Cisco WLC 5508 with 3702APs - mobile hotspot for 2000 Guest users

Cisco WLC 5508 with 3702APs - mobile hotspot for 2000 Guest users
I've been given a fantastic "opportunity" by my boss to use our existing wireless infrastructure to provide internet access to potentially upto 2000 VIP guests arriving with BYOD devices, in a very densely populated area for a 3 day event. We are talking an area of approx 200m x 15m. Think of it as an awards ceremony/concert. The solution will also be mobile so we will be using internet breakout from different telcos as it will move to approx 20 countries. The area is also incredibly densely populated with other wifi APs. I did a brief site survey and AirMagnet could detect over 2500 other 'rogue' APs from where I was stood! I hope CleanAir works!
We need a simple authentication method for them to connect with zero admin from our side. We don't want to just offer up a rolling daily PSK as that's a bit amateur and we don't really want the VIP guests sharing the PSK with others during their stay. Ideally they could self-provision by providing an email address.
I know the WLC can handle webauth for local users but I don't think it scales very well. ie I don't think I can offer the account to several hundred people.
Cisco ISE looks a very expansive (and expensive) product but I don't think we need all it's capabilities (do I?). It would be nice to just ask a potential user for their email address and grant them access and email them next year. I've seen Cisco NAC but that looks over the top too for just guest users who will only be accessing a shared internet connection.
I've seen 3rd party supposed software solutions from Kiosk Antamedia etc do they work with Cisco Enterprise WLC solutions?
We'd like to limit users to a certain (low) bandwidth and block (say) torrent traffic to keep the general user experience worthwhile.
Does anybody have any case study documents or experience of such a project? As well as the authentication it's how well the APs will handle the dense potential number of clients trying to connect in such a confined space.
Any suggestions would be gratefully appreciated from the knowledgeable community.
Cheers,
Mike

Hi Rasika,
We are having WLC 5508 model with software version running 7.4.121.0. AP Models are AIR-CAP2602I.
Normally our WAN links are good even while the issue pertains. We are connected to remote offices over ipsec site to site vpn for WAN. The link latency in WLC between the AP and the controller shows <1ms.
currently the Guest network is using WPA2-PSK auth given in the controller. we are trying to find a option to make the Guest wireless auth local to the office, and see if this solves the problem.
any suggestions,
Thank you,
Arjun

WLC 5508 with LAP-1142n - Several Errors

Hello all,
I had installed a WLC 5508 with 7 LAP 1142n and 2 converted AP 1131abg.
I am seeing some errors relating 2 issues.
1st- One particular AP 1142 is disassociating and reseting the radios.
/* Style Definitions */
table.MsoNormalTable
{mso-style-name:"Table Normal";
mso-tstyle-rowband-size:0;
mso-tstyle-colband-size:0;
mso-style-noshow:yes;
mso-style-priority:99;
mso-style-qformat:yes;
mso-style-parent:"";
mso-padding-alt:0cm 5.4pt 0cm 5.4pt;
mso-para-margin:0cm;
mso-para-margin-bottom:.0001pt;
mso-pagination:widow-orphan;
font-size:10.0pt;
font-family:"Times New Roman","serif";}
Thu Oct 28 11:50:49 2010
AP's Interface:0(802.11b)   Operation State Up: Base Radio MAC:e8:04:62:23:ac:e0 Cause=Radio interface   reset. Status:NA
Thu Oct 28 11:50:49 2010
AP's Interface:0(802.11b)   Operation State Down: Base Radio MAC:e8:04:62:23:ac:e0 Cause=Radio interface   reset. Status:NA
Thu Oct 28 11:50:49 2010
AP's Interface:1(802.11a)   Operation State Up: Base Radio MAC:e8:04:62:23:ac:e0 Cause=Radio interface   reset. Status:NA
Thu Oct 28 11:50:49 2010
AP's Interface:1(802.11a)   Operation State Down: Base Radio MAC:e8:04:62:23:ac:e0 Cause=Radio interface   reset. Status:NA
Thu Oct 28 11:50:46 2010
AP's Interface:1(802.11a) Operation   State Up: Base Radio MAC:e8:04:62:23:ac:e0 Cause=Radio reset due to Init.   Status:NA
Thu Oct 28 11:50:46 2010
AP's Interface:0(802.11b)   Operation State Up: Base Radio MAC:e8:04:62:23:ac:e0 Cause=Radio reset due to   Init. Status:NA
Thu Oct 28 11:50:46 2010
AP 'AP3', MAC:   e8:04:62:23:ac:e0 disassociated previously due to AP Reset. Uptime: 1 days,   10 h 24 m 23 s . Last reset reason: operator changed 11g mode.
Thu Oct 28 11:50:35 2010
AP Disassociated. Base Radio   MAC:e8:04:62:23:ac:e0
Thu Oct 28 11:50:35 2010
AP's Interface:1(802.11a)   Operation State Down: Base Radio MAC:e8:04:62:23:ac:e0 Cause=New Discovery Status:NA
Thu Oct 28 11:50:35 2010
AP's Interface:0(802.11b) Operation   State Down: Base Radio MAC:e8:04:62:23:ac:e0 Cause=New Discovery Status:NA
I had some search, and the new discovery cause, might be that the AP didnt know what WLC do associate, in a multi-controller environment. This is not the case. I only have one WLC in the same management vlan.
2st-The Radius server is beeing related in the logs as been deactivated. I raise the server time-out on Radius configuration option, but it still continues to do it.
/* Style Definitions */
table.MsoNormalTable
{mso-style-name:"Table Normal";
mso-tstyle-rowband-size:0;
mso-tstyle-colband-size:0;
mso-style-noshow:yes;
mso-style-priority:99;
mso-style-qformat:yes;
mso-style-parent:"";
mso-padding-alt:0cm 5.4pt 0cm 5.4pt;
mso-para-margin:0cm;
mso-para-margin-bottom:.0001pt;
mso-pagination:widow-orphan;
font-size:10.0pt;
font-family:"Times New Roman","serif";}
Thu Oct 28 10:24:41 2010
RADIUS server 10.67.128.36:1812 deactivated in global list
Thu Oct 28 10:24:41 2010
RADIUS server 10.67.128.36:1812 failed to respond to request (ID 172)   for client e8:06:88:51:c0:2b / user 'unknown'
Is this meaning the WLC stop sending request to the Radius Server ? We dont have BackUp Radius.
As far as i know, its always the same mac-address client that is associated to that error, maybe a iphone.
I had so many clients in that SSID and they are all working good.
The Radius server is a NPS from windows Server 2008
/* Style Definitions */
table.MsoNormalTable
{mso-style-name:"Table Normal";
mso-tstyle-rowband-size:0;
mso-tstyle-colband-size:0;
mso-style-noshow:yes;
mso-style-priority:99;
mso-style-qformat:yes;
mso-style-parent:"";
mso-padding-alt:0cm 5.4pt 0cm 5.4pt;
mso-para-margin:0cm;
mso-para-margin-bottom:.0001pt;
mso-pagination:widow-orphan;
font-size:10.0pt;
font-family:"Times New Roman","serif";}
, and the client says that the medium response time is 0,02 sec, so im wondering why the controller is not getting response from Radius for a particular client?! My client also says, that didnt found any log related to that mac-address client ... what is weird...
WLC with last software available 7.0.164
Hope some one help me here.
Best Regards,
Bruno Petrónio

Thanks Scott,
I understand what you are mentioning, and i really didnt do it yet.
I realize that the primary controller was not configured on the
/* Style Definitions */
table.MsoNormalTable
{mso-style-name:"Table Normal";
mso-tstyle-rowband-size:0;
mso-tstyle-colband-size:0;
mso-style-noshow:yes;
mso-style-priority:99;
mso-style-qformat:yes;
mso-style-parent:"";
mso-padding-alt:0cm 5.4pt 0cm 5.4pt;
mso-para-margin:0cm;
mso-para-margin-bottom:.0001pt;
mso-pagination:widow-orphan;
font-size:10.0pt;
font-family:"Times New Roman","serif";}
Wireless –> All APs –> High Availability tab, and did it only to the AP that is taking this beahviour.
Is this mandatory for a 1 controller only ?
No mather what the manual say, after that the AP is rebooting 2 mins in 2 mins... with the same kind of messages.
The interface on the switch is getting a few input errors and the same numbers of crc... but are so few...
Next step ... i will change it to another one's place/pathing cable.
Regarding the Radius messages... any ideas ?
I'm already on 30 sec's of server timeout.
Best Regards,
Bruno Petrónio

Deployment of WLC-5508 with 2702i-D have performance issue.

Hi Team,
We have centrally deployed WLC-5508 with 50 AP licence along with HA scenario. we have 3 locations.
1- HQ. have 26 AP with POWINJ5.
2- Branch location A- 8 AP with POWINJ5.
3. Branch location B have 8 AP with POWINJ4.
my exception is to achieve that single SSID with dynamic VLAN from group police (NPS). MY HO have 26 AP and those are working in local mode.
and branches are connected through flexconnect mode. and all are working with different-2 NPS.
Now i am facing a problem with this deployment are following.
1- branch A have performance issue.
2- HQ have performance issue.
3- i don't want to go with dedicated NPS for every location.
In order to achieve this deployment i want only single SSID with primary and secondary NPS at my HQ with dynamic VLAN for respective departmental users vlans..
above is my problem and concern. otherwise i am successfully achieving this solution with dedicated NPS with single group policy. but when i am going forward to achieve my expectation that time i am facing authentication issue at my HQ and sometimes am not able to get proper VLAN IPs. at my HQ.
kindly help me in that to understand where I am doing wrong things to achieve my expectation.
Thanks.
Nalin

I am facing 2 different problems.
1st issue- in existing setup we have throughput issue. (while downloading or uploading any data from the internet or Intranet, that time wireless clients are facing slowness of the Speed. and same time when i am trying from LAN i am not facing any issue)
2nd Issue- I want to achieve only single SSID with primary and secondary NPS (AD group is bind with vlan Attributes) with dynamic VLAN for respective departmental users.
for Issue no 2 i have created SSID to achieve the single ssid parameter for every location. in order to achieve i have change all access points mode local to Flexconnect mode after that i have created AP groups location wise and then create flexconnect Groups where i have mapped all the vlan through AAA VLAN-ACL mapping. created interface group and mapped all the vlans in that group.
for more understanding please go through the below mentioned CLI view.
Cisco Controller) >show wlan apgroups
Total Number of AP Groups........................ 4
Site Name........................................ GURGAON-AP-GROUP
Site Description................................. GURGAON-AP-GROUP
Venue Group Code................................. Unspecified
Venue Type Code.................................. Unspecified
NAS-identifier................................... Fractal-WLC1
Client Traffic QinQ Enable....................... FALSE
DHCPv4 QinQ Enable............................... FALSE
AP Operating Class............................... Not-configured
Capwap Prefer Mode............................... Not-configured
RF Profile
2.4 GHz band..................................... <none>
5 GHz band....................................... <none>
WLAN ID Interface Network Admission Control Radio Pol icy
3 gurgaon-interface Disabled None
--More-- or (q)uit
4 gurgaon-guest Disabled None
*AP3600 with 802.11ac Module will only advertise first 8 WLANs on 5GHz radios.
AP Name Slots AP Model Ethernet MAC Location Port Country Priority
GUR-AP-01 2 AIR-CAP2702I-D-K9 f4:4e:05:78:ae:e4 default location 1 IN 1
GUR-AP-05 2 AIR-CAP2702I-D-K9 f4:4e:05:80:b5:18 default location 1 IN 1
GUR-AP-03 2 AIR-CAP2702I-D-K9 bc:16:65:13:71:00 default location 1 IN 1
GUR-AP-07 2 AIR-CAP2702I-D-K9 f4:4e:05:80:b3:f8 default location 1 IN 1
GUR-AP-06 2 AIR-CAP2702I-D-K9 f4:4e:05:80:b3:e0 default location 1 IN 1
GUR-AP-08 2 AIR-CAP2702I-D-K9 f4:4e:05:45:78:98 default location 1 IN 1
GUR-AP-02 2 AIR-CAP2702I-D-K9 f4:4e:05:80:b3:2c default location 1 IN 1
GUR-AP-04 2 AIR-CAP2702I-D-K9 f4:4e:05:78:ae:64 default location 1 IN 1
GUR-AP-09 2 AIR-CAP2702I-D-K9 f4:4e:05:80:b4:44 default location 1 IN 1
Site Name........................................ MUMBAI-AP-GROUP
Site Description................................. MUMBAI-AP-GROUP
Venue Group Code................................. Unspecified
Venue Type Code.................................. Unspecified
--More-- or (q)uit
NAS-identifier................................... Fractal-WLC1
Client Traffic QinQ Enable....................... FALSE
DHCPv4 QinQ Enable............................... FALSE
AP Operating Class............................... Not-configured
Capwap Prefer Mode............................... Not-configured
RF Profile
2.4 GHz band..................................... <none>
5 GHz band....................................... <none>
WLAN ID Interface Network Admission Control Radio Policy
1 group for mumbai Disabled None
2 guest wifi Disabled None
*AP3600 with 802.11ac Module will only advertise first 8 WLANs on 5GHz radios.
AP Name Slots AP Model Ethernet MAC Location Port Country Priority
FAL-7-AP08 2 AIR-CAP2702I-D-K9 f0:7f:06:8d:24:d8 7th Floor 1 IN 3
--More-- or (q)uit
FAL-7-AP10 2 AIR-CAP2702I-D-K9 f0:7f:06:8d:25:18 7th Floor 1 IN 1
FAL-7-AP14 2 AIR-CAP2702I-D-K9 f0:7f:06:bf:ad:e8 7th Floor 1 IN 1
FAL-7-AP01 2 AIR-CAP2702I-D-K9 f0:7f:06:bf:b0:4c 7th Floor 1 IN 1
FAL-7-AP07 2 AIR-CAP2702I-D-K9 f0:7f:06:30:92:bc 7th Floor 1 IN 1
FAL-7-AP13 2 AIR-CAP2702I-D-K9 f0:7f:06:30:91:80 7th Floor 1 IN 1
FAL-7-AP02 2 AIR-CAP2702I-D-K9 f0:7f:06:30:91:94 7th Floor 1 IN 1
FAL-7-AP05 2 AIR-CAP2702I-D-K9 f0:7f:06:30:91:e8 7th Floor 1 IN 1
FAL-7-AP12 2 AIR-CAP2702I-D-K9 f0:7f:06:8d:25:f0 7th Floor 1 IN 3
FAL-7-AP03 2 AIR-CAP2702I-D-K9 f0:7f:06:8d:25:e4 7th Floor 1 IN 1
FAL-7-AP06 2 AIR-CAP2702I-D-K9 f0:7f:06:30:91:84 7th Floor 1 IN 3
FAL-7-AP04 2 AIR-CAP2702I-D-K9 f0:7f:06:bf:b0:14 7th Floor 1 IN 1
FAL-7-AP09 2 AIR-CAP2702I-D-K9 f0:7f:06:92:b4:c8 7th Floor 1 IN 3
FAL-7-AP11 2 AIR-CAP2702I-D-K9 f0:7f:06:30:93:08 7th Floor 1 IN 1
Site Name........................................ MUMBAI-THIRD-FLOOR-AP
Site Description................................. MUMBAI-THIRD-FLOOR-AP
Venue Group Code................................. Unspecified
Venue Type Code.................................. Unspecified
NAS-identifier................................... Fractal-WLC1
Client Traffic QinQ Enable....................... FALSE
--More-- or (q)uit
DHCPv4 QinQ Enable............................... FALSE
AP Operating Class............................... Not-configured
Capwap Prefer Mode............................... Not-configured
RF Profile
2.4 GHz band..................................... <none>
5 GHz band....................................... <none>
WLAN ID Interface Network Admission Control Radio Policy
1 group for mumbai Disabled None
2 guest wifi Disabled None
*AP3600 with 802.11ac Module will only advertise first 8 WLANs on 5GHz radios.
AP Name Slots AP Model Ethernet MAC Location Port Country Priority
FAL-3-AP07 2 AIR-CAP2702I-D-K9 f0:7f:06:30:91:a4 3rd Floor 1 IN 3
FAL-3-AP09 2 AIR-CAP2702I-D-K9 f0:7f:06:8d:25:94 3rd Floor 1 IN 3
FAL-3-AP11 2 AIR-CAP2702I-D-K9 f4:0f:1b:73:00:74 3rd Floor- Eurek 1 IN 3
FAL-3-AP06 2 AIR-CAP2702I-D-K9 f0:7f:06:bf:ae:d0 3rd Floor 1 IN 3
--More-- or (q)uit
FAL-3-AP10 2 AIR-CAP2702I-D-K9 f0:7f:06:92:b5:88 3rd Floor 1 IN 3
FAL-3-AP08 2 AIR-CAP2702I-D-K9 f0:7f:06:92:b4:9c 3rd Floor 1 IN 3
FAL-3-AP03 2 AIR-CAP2702I-D-K9 f0:7f:06:bf:af:a0 3rd Floor 1 IN 1
FAL-3-AP12 2 AIR-CAP2702I-D-K9 f0:7f:06:92:b3:fc 3rd Floor- Eurek 1 IN 3
FAL-3-AP02 2 AIR-CAP2702I-D-K9 f0:7f:06:8d:25:28 3rd Floor 1 IN 3
FAL-3-AP01 2 AIR-CAP2702I-D-K9 f0:7f:06:92:b4:f4 3rd Floor 1 IN 3
FAL-3-AP04 2 AIR-CAP2702I-D-K9 f0:7f:06:30:92:8c 3rd Floor 1 IN 2
FAL-3-AP05 2 AIR-CAP2702I-D-K9 f0:7f:06:30:91:f4 3rd Floor 1 IN 3
Site Name........................................ RAHEJA-AP-GROUP
Site Description................................. RAHEJA-AP-GROUP
Venue Group Code................................. Unspecified
Venue Type Code.................................. Unspecified
NAS-identifier................................... Fractal-WLC1
Client Traffic QinQ Enable....................... FALSE
DHCPv4 QinQ Enable............................... FALSE
AP Operating Class............................... Not-configured
Capwap Prefer Mode............................... Not-configured
RF Profile
--More-- or (q)uit
2.4 GHz band..................................... <none>
5 GHz band....................................... <none>
WLAN ID Interface Network Admission Control Radio Policy
5 raheja-interface Disabled None
2 raheja-guest Disabled None
*AP3600 with 802.11ac Module will only advertise first 8 WLANs on 5GHz radios.
AP Name Slots AP Model Ethernet MAC Location Port Country Priority
FAL-RAHEJA-AP04 2 AIR-CAP2702I-D-K9 f0:7f:06:8d:24:1c Near Meeting Roo 1 IN 3
FAL-RAHEJA-AP02 2 AIR-CAP2702I-D-K9 f0:7f:06:8d:37:3c Confrennce Room 1 IN 3
FAL-RAHEJA-AP03 2 AIR-CAP2702I-D-K9 f0:7f:06:30:93:48 Near Confrence R 1 IN 3
FAL-RAHEJA-AP05 2 AIR-CAP2702I-D-K9 f0:7f:06:bf:ae:c0 Near Meeting Roo 1 IN 3
FAL-RAHEJA-AP06 2 AIR-CAP2702I-D-K9 f0:7f:06:92:b3:a0 Near Server Room 1 IN 3
FAL-RAHEJA-AP01 2 AIR-CAP2702I-D-K9 f0:7f:06:92:b3:20 Reception Area 1 IN 3
FAL-RAHEJA-AP08 2 AIR-CAP2702I-D-K9 f0:7f:06:8d:25:68 USER BAY ROAD si 1 IN 1
FAL-RAHEJA-AP09 2 AIR-CAP2702I-D-K9 f0:7f:06:92:b4:d4 Training Room 1 IN 1
--More-- or (q)uit
Site Name........................................ default-group
Site Description................................. <none>
NAS-identifier................................... Fractal-WLC1
Client Traffic QinQ Enable....................... FALSE
DHCPv4 QinQ Enable............................... FALSE
AP Operating Class............................... Not-configured
Capwap Prefer Mode............................... Not-configured
RF Profile
2.4 GHz band..................................... <none>
5 GHz band....................................... <none>
WLAN ID Interface Network Admission Control Radio Policy
1 group for mumbai Disabled None
2 guest wifi Disabled None
3 gurgaon-interface Disabled None
4 gurgaon-guest Disabled None
5 raheja-interface Disabled None
6 test Disabled None
Cisco Controller) >show flexconnect group summary
FlexConnect Group Summary: Count: 4
Group Name # Aps
Gurgaon-AP 9
HQ-3RD-FLR-AP-GROUP 12
HQ-7THFLR-AP-GROUP 14
Raheja-AP-Group 8
(Cisco Controller) >show flexconnect group detail Gurgaon-AP
Number of AP's in Group: 9
bc:16:65:13:71:00 GUR-AP-03 Joined Flexconnect
f4:4e:05:45:78:98 GUR-AP-08 Joined Flexconnect
f4:4e:05:78:ae:64 GUR-AP-04 Joined Flexconnect
f4:4e:05:78:ae:e4 GUR-AP-01 Joined Flexconnect
f4:4e:05:80:b3:2c GUR-AP-02 Joined Flexconnect
f4:4e:05:80:b3:e0 GUR-AP-06 Joined Flexconnect
f4:4e:05:80:b3:f8 GUR-AP-07 Joined Flexconnect
f4:4e:05:80:b4:44 GUR-AP-09 Joined Flexconnect
f4:4e:05:80:b5:18 GUR-AP-05 Joined Flexconnect
Efficient AP Image Upgrade ..... Disabled
Master-AP-Mac Master-AP-Name Model Manual
Group Radius Servers Settings:
Type Server Address Port
Primary Unconfigured Unconfigured
Secondary Unconfigured Unconfigured
--More-- or (q)uit
Group Radius AP Settings:
AP RADIUS server............ Disabled
EAP-FAST Auth............... Disabled
LEAP Auth................... Disabled
EAP-TLS Auth................ Disabled
EAP-TLS CERT Download....... Disabled
PEAP Auth................... Disabled
Server Key Auto Generated... No
Server Key.................. <hidden>
Authority ID................ 436973636f0000000000000000000000
Authority Info.............. Cisco A_ID
PAC Timeout................. 0
Multicast on Overridden interface config: Disabled
DHCP Broadcast Overridden interface config: Disabled
Number of User's in Group: 0
Vlan :........................................... 203
Ingress ACL :................................... None
Egress ACL :.................................... None
Vlan :........................................... 205
Ingress ACL :................................... None
Egress ACL :.................................... None
Vlan :........................................... 204
--More-- or (q)uit
Ingress ACL :................................... None
Egress ACL :.................................... None
Vlan :........................................... 206
Ingress ACL :................................... None
Egress ACL :.................................... None
Vlan :........................................... 207
Ingress ACL :................................... None
Egress ACL :.................................... None
Vlan :........................................... 208
Ingress ACL :................................... None
Egress ACL :.................................... None
Vlan :........................................... 209
Ingress ACL :................................... None
Egress ACL :.................................... None
Vlan :........................................... 210
Ingress ACL :................................... None
Egress ACL :.................................... None
Vlan :........................................... 211
Ingress ACL :................................... None
Egress ACL :.................................... None
Vlan :........................................... 212
Ingress ACL :................................... None
Egress ACL :.................................... None
--More-- or (q)uit
Vlan :........................................... 216
Ingress ACL :................................... None
Egress ACL :.................................... None
Vlan :........................................... 217
Ingress ACL :................................... None
Egress ACL :.................................... None
Vlan :........................................... 218
Ingress ACL :................................... None
Egress ACL :.................................... None
Group-Specific FlexConnect Wlan-Vlan Mapping:
WLAN ID Vlan ID
WLAN ID SSID Central-Dhcp Dns-Override Nat-Pat
(Cisco Controller) >
(Cisco Controller) >show wlan summary
Number of WLANs.................................. 6
WLAN ID WLAN Profile Name / SSID Status Interface Name PMIPv6 Mobility
1 FRACTAL-EMP-MUMBAI / FRACTAL Enabled group for mumbai none
2 FRACTAL-GUEST / FRACTAL-GUEST Enabled guest wifi none
3 FRACTAL-EMP-GURGAON / FRACTAL-GURGAON Enabled gurgaon-interface none
4 GURGAON-GUEST / FRACTAL-GUEST-GURGAON Enabled gurgaon-guest none
5 RAHEJA-EMP-WIRELESS / FRACTAL-R Enabled raheja-interface none
6 TEST-SSID / TEST-SSID Enabled test none
hope this will give you proper understanding.

HT4962 I have an Ipod Touch 2nd generation with version 4.2.1 IOS and it no longer seems to be recognized as a device when I plug into my computer. I want to update my sync settings but can't do this without being able to select the device. Any suggestion

I have an Ipod touch 2nd generation with version 4.2.1 IOs and it is no longer recognized as a device when I plug into my computer. This means I can not change synch settings - any ideas on what I need to do ?

See:
iOS: Device not recognized in iTunes for Windows
I would start with:
Removing and reinstalling iTunes, QuickTime, and other software components for Windows Vista or Windows 7
or
Removing and Reinstalling iTunes, QuickTime, and other software components for Windows XP

WLC 5508 software version working with ISE1.1.2

Hi,
My understanding is that for fully WLC 5508 integration with ISE 1.1.2, it needs Version 7.2.103.0. Question is if customer has 5508 with either 7.0.230 or 7.0.98, and ISE 1.1.2, can AAA part work? what part will not work, any potential issue if they don't upgrade 5508 to 7.2.103?
Thanks in advance!
Tina

Please check the below Table:
Table 1 Supported Network Access Devices
Device
Minimum OS Version
MAB
802.1X
Web Auth
Session CoA
VLAN
DACL
SGA
IOS Sensor
CWA
LWA
Wireless LAN Controller (WLC) 2500, 5500
7.2.103.0
No6
Yes
Yes
Yes
Yes
Yes
Yes
Yes
No
Ref. Link: http://www.cisco.com/en/US/docs/security/ise/1.1.1/compatibility/ise_sdt.html#wp55038

Emergency Version for WLC 5508 with 6.0.188

The release notes for 6.0.188 talks abt 5.2.157.0 ER.aes. But 5508 does not like the file AIR-WLC4400-K9-5-2-157-0-ER.aes.
How can I get the boot loader on WLC 5508?
On WLC 5508...
Product Version.................................. 6.0.188.0
Bootloader Version............................... 1.0.1
Field Recovery Image Version..................... 6.0.182.0
On WLC 4404
Product Version.................................. 6.0.188.0
RTOS Version..................................... 6.0.188.0
Bootloader Version............................... 4.2.205.0
Emergency Image Version.......................... N/A ----------> Even though I installed 5-2-157-0-ER.aes it does not show here... Bug???

Ok. In the release notes of 6.0.188 they should have seperated for 5508.
On WLC 4404
Product Version.................................. 6.0.188.0
RTOS Version..................................... 6.0.188.0
Bootloader Version............................... 4.2.205.0
Emergency Image Version.......................... N/A
When u say "The n/a issue is a bug but its with the primary image, not the ER image"
Do you mean that because my primary image is 6.0.188 which has bug to not take or show the ER image?

WLC 5508 with 7.4.100.0 software

Hi All,
One of my client has a wireless setup with WLC 5508 and 1142N APs. It was running with a good coverage for access points when WLC was running with 7.0 software version. Last week I upgraded the software to latest 7.4.100.0 version. After that the coverage of APs are very low.
Can someone help me regarding this issue.
Thanks
Sadiq

I didn't have coverage issues per say, but my 1142 APs kept disassociating randomly
TAC suggested running these commands. Which has stopped the APs leaving the building.
> config 802.11a disable network
> config 802.11a 11nSupport a-mpdu tx priority all disable
> config 802.11a 11nSupport a-mpdu tx scheduler disable
> config 802.11a enable network
> config 802.11b disable network
> config 802.11b 11nSupport a-mpdu tx priority all disable
> config 802.11b 11nSupport a-mpdu tx scheduler disable
> config 802.11b enable network
Aggregation is the process of grouping packet data frames together rather than transmitting them separately. Two aggregation methods are available: Aggregated MAC Protocol Data Unit (A-MPDU) and Aggregated MAC Service Data Unit (A-MSDU). A-MPDU is performed in the software whereas A-MSDU is performed in the hardware.
Disables the 802.11n-5 GHz A-MPDU transmit aggregation scheduler.

DEBUG-4-INVALID_MODULE on the WLC 2504 with version 7.6.100????

Hi!!! Please help with the solution.
I have one WLC 2504, 4 Cisco 1141 APs and one AP 1602.
Yesterday, I upgrade the WLC with version 7.5.102 to version 7.6.100.
After the upgrade in Message Logs on the WLC at the same time see the following message:
*RRM-MGR-5_0-GRP: Jan 23 08:44:25.449: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 08:35:41.189: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 08:34:17.373: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 08:25:32.125: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 08:24:09.309: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 08:15:23.013: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 08:14:01.213: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 08:05:13.949: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 08:03:53.149: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 07:55:04.905: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 07:53:45.086: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 07:44:55.813: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 07:43:37.010: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 07:34:46.749: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 07:33:28.930: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 07:24:37.669: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 07:23:20.865: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 07:14:28.593: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 07:13:12.789: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 07:04:19.529: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 07:03:04.729: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 06:54:10.493: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 06:52:56.689: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 06:44:01.445: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 06:42:48.645: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.
*sntpReceiveTask: Jan 23 06:35:22.218: #LOG-4-Q_IND: debug.c:2636 Unhandled debug module 5005.[...It occurred 19 times.!]
*RRM-MGR-2_4-GRP: Jan 23 06:33:48.070: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 06:32:36.266: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 06:23:39.030: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 06:22:28.226: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 06:13:29.986: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 06:12:20.186: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 06:03:20.930: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 06:02:12.130: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 05:53:11.890: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 05:52:04.090: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 05:43:02.838: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 05:41:56.039: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 05:32:53.790: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 05:31:47.986: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 05:22:44.758: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 05:21:39.950: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 05:12:35.718: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 05:11:31.910: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 05:02:26.670: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 05:01:23.859: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 04:52:17.606: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 04:51:15.794: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 04:42:08.566: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 04:41:07.750: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 04:31:59.506: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 04:30:59.703: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 04:21:50.450: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 04:20:51.646: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 04:11:41.402: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 04:10:43.598: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 04:01:32.326: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 04:00:35.522: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 03:51:23.258: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 03:50:27.442: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 03:41:14.182: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 03:40:19.378: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 03:31:05.106: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 03:30:11.302: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 03:20:56.042: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 03:20:03.242: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 03:10:46.978: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 03:09:55.178: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 03:00:37.902: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 02:59:47.102: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 02:50:28.826: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 02:49:39.026: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 02:40:19.782: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 02:39:30.983: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 02:30:10.742: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 02:29:22.942: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 02:20:01.698: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 02:19:14.886: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 02:09:52.646: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 02:09:06.842: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 01:59:43.587: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 01:58:58.783: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 01:49:34.546: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 01:48:50.742: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 01:39:25.494: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 01:38:42.687: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 01:29:16.454: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 01:28:34.642: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 01:19:07.402: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 01:18:26.594: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 01:08:58.362: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 01:08:18.554: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 00:58:49.322: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 00:58:10.514: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 00:48:40.266: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 00:48:02.467: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 00:38:31.222: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 00:37:54.411: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 00:28:22.174: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 00:27:46.374: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 00:18:13.106: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 00:17:38.306: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 00:08:04.062: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 00:07:30.262: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 22 23:57:55.022: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 22 23:57:22.222: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 22 23:47:45.958: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 22 23:47:14.158: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 22 23:37:36.906: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 22 23:37:06.106: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 22 23:27:27.826: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 22 23:26:58.026: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 22 23:17:18.762: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 22 23:16:49.962: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 22 23:07:09.686: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 22 23:06:41.870: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.
With what may be the problem exists? Any suggestion?

Have you upgraded the FUS to 1.8.0.0? What happens if you try to boot from v7.5 do you see the messages and maybe boot back to v7.6?
Here is what the doc mentions about the error
Error Message %DEBUG-4-INVALID_MODULE: Unhandled debug module [dec].
Explanation This module cannot be debugged.
Recommended Action Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.
http://www.cisco.com/en/US/docs/wireless/controller/message/guide/msgs4.html#wp1000708
Sent from Cisco Technical Support iPhone App

WLC 5508 with AD, NPS but without GPO, how?

Hi,
I didn't found anything related to what I'm trying to do so I though I would create a new discussion...
I would like to setup a new WLAN and to be able to connect, a user will have to enter his username/password that will be confirmed using NPS and Active Directory. The problem is, I don't want to use a GPO, I would like to only verify if the user is a member of a AD group, let's say "wlan_access".
I don't want to install anything ( certificate, GPO, creating a WLAN configuration ) on the user's PC/laptop, only AD validation using NPS as a Radius server.
If a user is part of that AD group, after he enter his credential he will have access to that WLAN.
Is it possible to setup that? How should I configured the WLAN in my WLC 5508 ( running 7.2.110.0 )? How should I configure NPS ( Windows 2008 R2 Enterprise )?
Thanks a lot for your help and answers.
Guillaume

Hi guys,
With the info Stephen Rodriguez gave, it looks like I won't be able to do what we want without doing config on the user's devices ( laptop, ipad, etc.. ).
@Joseph Vasanth Louis Yes the message is from the event viewer of the NPS server. In the connection request policies, there's not much config, I let the option "Authentication Methods" in the tab Settings uncheck, so it won't override the settings in the Network Policies.
I though it was possible to have authentication using NPS and Active Directoy without installing anything on the user's devices and still having a secured wireless network ( not like a hotspot ).
The solution I think is the most workable is with the PEAP or PSK, with a certificate but even that...the user will have to create the WLAN profil on his laptop, so I'm not sure we want to go that way. I'll check for the PSK option, to see if the "Web Authentication" could be done using NPS.
Thanks guys for all your time and help. I'll continue my tests and keep you posted.

Cisco WLC 5508 with Nexus 5048 CDP error

Hello,
We got cisco WLC 5508 running 74.121.0
The WLC is connected to Nexus 5548 with dual-homed.
We receive CDP duplex mismatch from the Nexus switches.
Any ideas?

Can you check the duplex info. of the neighbor using
router#show cdp neighbors detail

Cisco wlc 5508 with 30 Vlan

Hello
i need your help
i want to configure Cisco WLC 5508 whith 03 vlans, 3750 as core swich
- management Vlan
- local-user vlan
- Guest Vlan
i want to know all steps or config to do on WLC
thx

Hi,
Just check this.
It may help u.
Wireless LAN Controller and Lightweight Access Point Basic Configuration Example
http://www.cisco.com/c/en/us/support/docs/wireless/4400-series-wireless-lan-controllers/69719-wlc-lwap-config.html
http://rscciew.wordpress.com/2014/01/22/configure-dynamic-interface-on-wlc/
Webauth for guest users:
http://www.cisco.com/c/en/us/support/docs/wireless-mobility/wlan-security/69340-web-auth-config.html
http://rscciew.wordpress.com/2014/06/19/wlc-webauth-configuration/
Regards

Upgrade two WLC 5508 with HA SSO from 7.5.102.0 to 7.6.130.0 combined with FUS 1.9

The running config is:
- Two WLC5508's in HA SSO setup running version 7.5.102.0
- about 130 x 2602i APs
I need to upgrade to 7.6.130.0 using the pre-download feature to minimize the network downtime.
Is it possible to transfer the 7.6 to the controllers and pre-download 7.6 to all APs, then do the FUS 1.9 upgrade and finally start the actual controller upgrade to 7.6.
So the steps would be:
1. Transfer 7.6 image to primary controller (do not reboot!), so still running 7.4 as active image.
2. Start pre-download of 7.6 image to all APs and wait till all APs have the new image (do not know how long it takes for 130 APs).
3. Upgrade both controllers with FUS 1.9 (HA should upgrade both controllers automatically) (takes about 45 minutes?)
4. Make 7.6 image the active/primary image on controllers and APs and reset controllers.
If the steps above will not work, I would need to upgrade FUS 1.9 which means 1 hour downtime and then start the pre-download to all APs. The pre-download can take a long time I heard, so I need to wait and wait before I can start the 7.6 upgrade, which means another 1 hour downtime.
This way I need two maintenance windows instead of one. So would it be possible to combine the pre-download and FUS?
Regards,
Bjorn

>Do I need to upgrade the FUS 1.9 before the 7.6 image or can I do the FUS afterwards? If I can do it afterwards, I can do the upgrades in the same maintenance window. This way I can start the pre-download the day before, so I am pretty sure the APs have the image at the time of the maintenance window.
>I cannot find any remarks about the required order of installation (FUS -> image or image -> FUS).
Release Notes for Wireless LAN Controller Field Upgrade Software for Release 1.9.0.0 - p2 :
* This release of the Field Upgrade Software is applicable to CISCO WLC's that are installed with the controller software release 6.0 and later.
So strict reading implies that you have to run 7.6 first.
M.

Unable to add SNMP server in WLC 5508 with 7.4.110

hi
I am trying to add 0.0.0.0/0 as SNMP address and netmask and i am getting an error saying the netmask is invalid.
is there a different way to set this?

Hi Roy,
This is strange.
I do not have a test WLC with this code to test, but command syntax is correct. I have verified it on my test controller in 7.0.116.0 & it is happy to accept it. Even 7.4 config guides does not show any other command syntax for this.
http://www.cisco.com/en/US/docs/wireless/controller/7.4/configuration/guides/consolidated/b_cg74_CONSOLIDATED_chapter_0111.html
One good thing is, this is the default setting once you create a snmp-community. It should have 0.0.0.0/0 as subnet/net mask & you do not require any changes for the default config.
"show snmpcommunity" output should show the config values for your SNMP community.
If you are trying to change it from configured subnet to default value, then as a work around you can re-create the snmp commnuity from fresh (delete & recreate)
If you have Cisco TAC assistance then log a case with them to see why this command is not accepting in your code of WLC
HTH
Rasika
**** Pls rate all useful responses ****

Roaming problem with WLC 5508 with Phone 7921

Hi to all,
i have one WLC with several AP1231 2.4 GHz. Everything works fine with PC and 7921 in normal condition (last firmware release 1.4.3.4).
But with 7921 there is a little problem: if i walk quicky along the warehouse and along lanes while i'm at the phone everything works well.
But the operator often have a phone call while he is on a forklift and he moves fast with this during the conversation.
In this case of fast moving, during the call, the call doesn't fall but often i do not hear 2/3 words consecutively so i can't understand the phrase.
I have already done a study of radio environment but there aren't interference, and roaming works good with walk speed, so i think that the problem is the operator's speed in forklift (i think at the max about 10-12 Km/h)
The question is that in this case it is possible to modify parameters of Client Roaming in WLC, to reduce this issue?
If yes, somone knows what are the best values in this environment for
Hysteresis
Minimum RSSI
Transition time
Scan threshold
Or someone knows other parameters to modify or any ideas?
Thanks a lot.

The 1.4.3.4 firmware scans nicely - it will typically scan each channel every 5 seconds.
How big are your cells? What power level are you using? With very small cells, it is certainly possible that the forklift can drive out of and into cells faster than the phone can scan for them.
You may want to increase your cell size (increase power.) Of course this also means that you will run the risk of co-channel interference. In which case you may need to disable some 2.4GHz radios.
Also - be sure that your APs are placed where the forklift can hear an AP that it needs to roam to well before it has to roam to it. For example, if the forklift is rolling straight down a corridor like this:
          | x |            |    |
__________|    |____________|    |_____
a              >>> forklift >>>                   b
----------|    |------------|    |-----
          |    |            | y |
then make sure that the APs that the forklift needs to use are at locations a and b, not x and y (assuming metal partitions where the lines are.)
Aaron

WLC 5508 with version 7.0.98.0 and AIR-LAP1242ag

Similar Messages

Maybe you are looking for