WLC 5508 WLAN SSID Problem

Hi,
I recently got a 5508 controller. I use 1 SSID for the employees on the main site (using certificate authentication). On the Remote sites I want to use the same SSID with different DHCP Servers (AP are configuring with HREAP mode). So I tried to configure different WLAN ID using the same SSID (I override DHCP Server IP Address). When I try to activate SSID, I got the following error : "WLAN with duplicate SSID's and L2 security policy found". I tryed to use "AP Group" and put the different WLAN ID in different AP Group but it dosen't work.
Anyone as an idea?
Thanks in advance
Regards,
Eric

Hi,
This is the expected behaviour!! and there is no way to overcome issue as the error thats popping up is self explanatory!! if you are using Internal WEB AUTH page then the HREAP local switching supports the internal WEB AUTH, and another thing is.. a single WLAN will do the Job!! You just need to configure Local switching on the WLAN so that, the clients in the central site use ( AP in local mode will use central side DHCP) and the AP in the HREAP will use the mapped VLAN to grab the IP!!
here is the link to do the same!!
http://www.cisco.com/en/US/products/ps6087/products_tech_note09186a0080736123.shtml#webauth
http://www.cisco.com/en/US/tech/tk722/tk809/technologies_configuration_example09186a00807cc3b8.shtml
Lemme know if htis answered ur question and please dont forget to rate the usefull posts!!
Regards
Surendra

Similar Messages

WLC 5508 - wlan stability problems

Hi.
I have a WLC 5508 with half a dozen LAPs (AIR-CAP3502I-E-K9).
They have been working but sometimes clients detect conectivity problems with the wlan.
Here is the message log I can obtain from the controller:
Nov 09 12:16:31.886: [ERROR] pemTimers.c 330: invalid interface name (john_doe) in mscb!!!*dot1xMsgTask: Nov 09 12:16:10.286: %DOT1X-3-MAX_EAPOL_KEY_RETRANS: 1x_ptsm.c:444 Max EAPOL-key M1 retransmissions exceeded for client 00:26:c6:12:e8:32Previous message occurred 7 times.Nov 09 11:55:24.682: [ERROR] pemTimers.c 330: invalid interface name (john_doe) in mscb!!!*apfReceiveTask: Nov 09 11:51:30.788: %RRM-3-RRM_LOGMSG: rrmChanUtils.c:290 RRM LOG: Airewave Director: Could not find valid channel lists for 802.11bg *spamApTask2: Nov 09 11:51:20.144: %DTLS-3-HANDSHAKE_FAILURE: openssl_dtls.c:631 Failed to complete DTLS handshake with peer 10.23.1.118*dot1xMsgTask: Nov 09 11:50:44.878: %DOT1X-3-MAX_EAPOL_KEY_RETRANS: 1x_ptsm.c:444 Max EAPOL-key M1 retransmissions exceeded for client e0:ca:94:93:be:67*apfReceiveTask: Nov 09 11:50:40.672: %RRM-3-RRM_LOGMSG: rrmChanUtils.c:290 RRM LOG: Airewave Director: Could not find valid channel lists for 802.11bg *apfReceiveTask: Nov 09 11:50:38.625: %RRM-3-RRM_LOGMSG: rrmChanUtils.c:290 RRM LOG: Airewave Director: Could not find valid channel lists for 802.11bg *apfReceiveTask: Nov 09 11:50:35.531: %RRM-3-RRM_LOGMSG: rrmChanUtils.c:290 RRM LOG: Airewave Director: Could not find valid channel lists for 802.11bg *apfReceiveTask: Nov 09 11:50:31.068: %RRM-3-RRM_LOGMSG: rrmChanUtils.c:290 RRM LOG: Airewave Director: Could not find valid channel lists for 802.11bg *apfReceiveTask: Nov 09 11:50:29.257: %RRM-3-RRM_LOGMSG: rrmChanUtils.c:290 RRM LOG: Airewave Director: Could not find valid channel lists for 802.11bg *apfReceiveTask: Nov 09 11:50:28.707: %RRM-3-RRM_LOGMSG: rrmChanUtils.c:290 RRM LOG: Airewave Director: Could not find valid channel lists for 802.11bg *apfReceiveTask: Nov 09 11:50:24.065: %RRM-3-RRM_LOGMSG: rrmChanUtils.c:290 RRM LOG: Airewave Director: Could not find valid channel lists for 802.11bg
Can somebody help me to understand these messages?
1)
*apfReceiveTask: Nov 09 11:50:24.065: %RRM-3-RRM_LOGMSG: rrmChanUtils.c:290 RRM LOG: Airewave Director: Could not find valid channel lists for 802.11bg
2)
Nov 09 11:55:24.682: [ERROR] pemTimers.c 330: invalid interface name (john_doe) in mscb!!!
3)
*dot1xMsgTask: Nov 09 11:50:44.878: %DOT1X-3-MAX_EAPOL_KEY_RETRANS: 1x_ptsm.c:444 Max EAPOL-key M1 retransmissions exceeded for client e0:ca:94:93:be:67
Thanks

1)
*apfReceiveTask: Nov 09 11:50:24.065: %RRM-3-RRM_LOGMSG: rrmChanUtils.c:290 RRM LOG: Airewave Director: Could not find valid channel lists for 802.11bg
//APs are rebooting. don't panic, check the up time of AP. This message seen when AP rebooted/freshly joined and waiting for wlc to assign channel.
2)
Nov 09 11:55:24.682: [ERROR] pemTimers.c 330: invalid interface name (john_doe) in mscb!!!
//It is cosmetic and can be ignored.
3)
*dot1xMsgTask: Nov 09 12:16:10.286: %DOT1X-3-MAX_EAPOL_KEY_RETRANS: 1x_ptsm.c:444 Max EAPOL-key M1 retransmissions exceeded for client 00:26:c6:12:e8:32
//Keys M1-M5 used for wireless auth, here client having struggle completing the auth process.
get output of, WLC>debug client

WLC 5508 - WLANs disabled after reboot

Hi,
I'm running 3 WLC 5508, 2 of them running image AIR-CT5500-K9-7-0-116-0.aes, one AIR-CT5500-LDPE-K9-7-0-116-0.aes.
On the 5508 running the LDPE-image, I have 9 WLANs (170,171,180,181,190,191,281,282,283), all defined with admin status "ENABLED".
WLANs 180,181,281 belong to a defined AP-group, WLAN 190,191,282 belong to a different AP-group.
WLANs 180,181,190,191 are defined as H-REAP. The H-REAP APs registers without any problems at the backup WLC and switches back successfully to the primary controller after recovering from reboot.
Unfortunately the WLANs 180,181,190,191 show status "DISABLED" every time the primary controller comes back and I have to enable them manually.
Doing exactly the same procedure with one of the other WLC, running AIR-CT5500-K9-7-0-116-0, I never face this problem.
Has anyone faced something similar ? Any hints or tipps are very much appreciated

I would like to pick up the discussion again. I had to upgrade the 2 WLC's involved in the scenarion and the WLANs are staying enabled. The APs are registering in a perfect time at the secondary 5508 and so do the clients.
After the primary 5508 comes back the LWAPPs are registering back to that WLC seemless and so do the clients but sometimes (not always) not without loosing the connections for about 15 secs, which is unacceptable since the applications will drop.
We also get the following error-msg:
*Sep 12 13:39:05.598: %AAA-3-BADSERVERTYPEERROR: Cannot process authentication server type radius (UNKNOWN)
*Sep 12 13:39:05.598: %DOT11-7-AUTH_FAILED: Station 0026.c730.88ae Authentication failed
Hass anyone faced something similar ?

WLC 5508 WPA Authentication Problems

Hello,
We have a WLC 5508 with 7.4.100.0 Firmware.
We are using 1141 and 1142 APs and we are having authentication problems with clients that are connecting to our WLAN with WPA+AES autentication. The clients receive in her laptop a password error, and we receive the following log in wlc:
Client Excluded: MACAddress:f8:f1:eb:dd:ff:cd Base Radio MAC :08:ad:dd:76:4d:30 Slot: 0 User Name: unknown Ip Address: unknown Reason:802.1x Authentication failed 3 times. ReasonCode: 4
The strange thing is that the problem is solved restarting the Access-points.
Anyone had this problem previusly?
Thanks in advance.

I made the configuration using the Cisco Recommended settings, the strange thing its that the users connect normally, until they starts with authentication problems. I restart the access points and the problem its solved.
Cisco Recommended and not recommended Authentication Settings
Security encryption settings need to be identical for WPA and WPA2 for TKIP and AES as shown in this image:
These images provide examples of incompatible settings for TKIP and AES:
Note: Be aware that security settings permit unsupported features.
These images provide examples of compatible settings:

WLC 5508 - WLAN, changing the SSID ?

It doesnt seem I am able to change the SSID of an active or disabled wlan via the web interface ?
Any ideas ?
Cheers
dave

no you cannot change it, you need to delete the whole SSID and set it up again.

WLC 5508 WLAN Changes

Hello all,
I have a pair of 5508s running in HA with a number of WLANs active. Whenever I make a change to a single WLAN, it seemingly causes ALL the WLANs to reset, resulting in a downtime of roughly 10-15 seconds. I first noticed this when I was managing the WLC on my office wireless network, which is also controlled by the WLC. Once I made a small change in another WLAN, I briefly lost internet connectivity. Has anyone else run into this same problem? Is this intended as designed, or is there a way to get around it? The WLC is running 7.3.101.0 and all of the WLANs are on FlexConnect, and they do not all share the same interface.
Thanks,
Wilson

I don't think it is by design at all. Without HA, a change in the WLAN only affects that WLAN. Now I'm guessing you also understand that there are issues with HA and you are on the first version of code that supports HA. Now I'm not saying that upgrading will fix it, but it would be a bit more stable but not 100%. I would wait until the v7.4 MR1 comes out which might be this month or maybe a few... I don't know. Or I would look at maybe the latest v7.3 code to upgrade to.
Sent from Cisco Technical Support iPhone App

WLC 6 WLAN Override problem

works function WLAN Override in controller WLC6?, we have tried it and it does not work, is a software problem?

Professorguy,
Does having to match profile name to SSID name result in not being able to have multiple authentication methods per SSID? That was supposed to be a feature of 4.0.206.
Thanks,

Cisco WLC 5508 WLAN Controller

Hallöchen kennt sich jemand mit den Dingern tiefgründiger aus? Ich hätte da mal ein frage bzgl. der interface Groups.
Und Zwar kann man ja mehrere Vlans (somit auch IP Ranges) in eine Gruppe packen und diese dann wiederum ein SSID zu ordnen. Kann mir jemand erklären wie indem Falle die IP Adresse Zuweisung (DHCP der Clients unterschieden wird?
Und die 2. Frage wäre kann man verschiedene LAG Gruppen bauen oder oder nimmt er automatisch alle 8 in eine LAG Gruppe?
Danke für eure Hilfe schonmal.

is ist poosible the to create more than one LAG portgroup or binds the controller all 8 ports automatically in the same group? My idea is to cerate a 3 groups for 3 costumers with 2GB uplinks to the bachground network.
When it comes to WLC, it's either you turn on LAG or you don't. You can only have one LAG.
Here's what we've done in our deployment:
We have a single outbound interface, let's call it INTERNET. We have multiple sites. So we create multiple dynamic interface with specific DHCP server.
We have created a PERL script and it's attached to our LINUX RADIUS box which specifies that all traffic goes out the INTERNET dynamic interface, however, each client gets an IP address based on the site where they come from.

Cisco WLC 5508 - WLAN Per-User Bandwidth Contracts

Hi,
I setup per-user bandwidth contracts on my guest anchor controller. The controller model is 5508 and firmware is 7.4.121.0. No Qos settings were configured on the foreign controllers.
The bandwidth limits for the WLAN worked correctly for a couple of weeks, then speed reduced to almost nothing. I removed the WLAN bandwidth limits and speed was back to normal again.
Has anyone else run into this issue? Any ideas why it might have happened?
Thanks,

If Scott does not mind an add-on. The 3850 also supports per client QOS.
Page 16 -
http://www.cisco.com/c/dam/en/us/products/collateral/switches/catalyst-3850-series-switches/guide_c07-727066.pdf

Wlc 5508 invalid ipad mac address

Hello,
Help me pls,
While configuring mac address filter on a WLC 5508 there is problem with mac address beginning with 77:....
I cant add it to WLC mac filter.
Thanks in advance

If you are using dot1x then no, the mac address is sent since the client does not receive an ip address till authetication succeeds.
Sent from Cisco Technical Support Android App

Mapping Multiple VLANs to Multiple SSIDs as one-one in WLC 5508 via H-REAP?

Hi All,
Can anyone please show me how to map a SSID/WLAN ID to a local vlan of a LAP in WLC 5508 using H-REAP local switched? The reason of doing this is to separate Data subnet/traffic from Voice as currently all 7925 handsets using same SSID as PCs. I would like to create two VLANs on APs and map them to two SSIDs. I could not see any option in WLC5508 to do this. Also when I change the AP mode from H-REAP to local and configuring sub interface using dot1q on the interface Gi0 then unable write running-config to startup-config because I get NVRAM Verification Failed as WLC protects any local changes on any registered LAP at NVRAM.
Your help is much appreciated.

Mehdi:
I am talking about HREAP groups, not AP groups.
You can not achieve what you want if you are using the same SSID on same AP with only a WLC (same AP with same SSID is mapped to different VLANs). You may need a radius server to dynamically assign a VLAN to the clients if you are using same SSID for data and voice.
If you are using different SSIDs for voice and data, you can map each SSID to its corresponding VLAN on the remote site using the VLAN mapping option under HREAP tab in the AP config page.
You can not configure the AP from its console. Lightweight APs can only be configured from the controller. (a few exceptions are available that do not apply here) .
HTH
Amjad
Rating useful replies is more useful than saying "Thank you"

WLC 5508 disable wlan client still connected

I have one wlc 5508 running on latest IOS 7.116, there is one wlan abc which i have disable status and disable broadcast, but randomly still i can see from wlc dashboard there is one client connected to this wlan abc. The moment i check on the client details, there is no client connected to that wlan and when return to dashboard, no more client connected to that wlan abc. This happened in randomly, it is bug or something else?

I would guess that the client entry also indicates "probing" as status. It means that the client is not connected. It is actually probing, so it"s looking for that SSID that it probably associated to in the past (so it remembers about it)

Cisco WLC 5508 assigning different SSID to few APs

Hello Everyone,
I have a WLC 5508 runing 8.0
Presently one SSID is assigned to all th APs registered with my WLC.
I want a different SSID to 2 of APs. Can anyone tell me how to do this?

Depend on WLAN ID number as well.
1. if WLAN ID number is greater than 16, then those SSID not visible in "default ap-group" & only in the APs in particular AP Group.
2. if WLAN ID number is lower than 16 then, by default it will advertise in APs in "default ap-grop". So if you add that WLAN to particular AP Group, then that WLAN advertised by APs in both AP groups (default & specific AP group)
HTH
Rasika
**** Pls rate all useful responses ****

WLC 5508 Multiple Interfaces for Multiple SSIDs

Hello guys,
I am trying to build a new network from scratch, I have the WLC 5508 w/ Aironet 3600e APs connected to my Netgear Smart Switches and a Linksys RV082 router that I'm using as my DHCP server with several VLANs for several stuff on my Switches.
I have 2 questions:
1. Can I have 5 Interfaces configured on 5 different VLANs, each SSID on each a different Port:
Port 1: Controller management only=> 192.168.x.x /24
Port 2: SSID 1: WiFi Internal=> 172.16.x.x/12 (Radius Auth with no sharing)
Port 3: SSID 2: WiFi Internal w/ sharing=> 192.168.x.x/24 (Radius Auth with sharing)
Port 4 :SSID 3: WiFi Guest=> 10.0.x.x/8 (Web Auth)
Port 5: SSID 4: WiFi IT=> 192.168.x.x/24 ( Radius or certificate Auth with access to the controller management interface)
2. How can I use the Controller as the DHCP server for all the WiFi traffic, and how should that be configured to work with my other DHCP server?

Yes you can... but you have to disable LAG. Each post will need to be connected to a dot1q trunk and you will only allow the vlan that is required for that port. Also on the interface, you will define what port is primary and what is backup. I'm guessing you will not be using the backup port. For example... port 1 that connects to a trunk port will only allow the management vlan. Here is a link to setup dhcp on the WLC
http://www.cisco.com/en/US/products/ps6366/products_tech_note09186a0080af5d13.shtml
Thanks,
Scott
Help out other by using the rating system and marking answered questions as "Answered"

WLC 5508 Problem with #DOT1X-3-INVALID_REPLAY_CTR

Hi all,
I have WLC 5508 with version 7.4.110.0 and with 13 AccessPoints.So 12 of this AP are AIR-LAP1142N-E-K9 and 1 is AIR-CAP3602I-E-K9.
Logs of my WLC are:
*Dot1x_NW_MsgTask_1: Jan 11 01:15:05.167: #DOT1X-3-INVALID_REPLAY_CTR: 1x_eapkey.c:360 Invalid replay counter from client 90:c1:15:c6:c3:49 - got 00 00 00 00 00 00 00 01, expected 00 00 00 00 00 00 00 02
*Dot1x_NW_MsgTask_4: Jan 11 01:09:41.015: #DOT1X-3-INVALID_REPLAY_CTR: 1x_eapkey.c:360 Invalid replay counter from client 5c:0a:5b:c1:16:34 - got 00 00 00 00 00 00 00 01, expected 00 00 00 00 00 00 00 02
*Dot1x_NW_MsgTask_3: Jan 11 01:03:32.269: #DOT1X-3-INVALID_REPLAY_CTR: 1x_eapkey.c:360 Invalid replay counter from client 40:b3:95:13:da:cb - got 00 00 00 00 00 00 00 03, expected 00 00 00 00 00 00 00 04
*Dot1x_NW_MsgTask_3: Jan 11 01:03:32.266: #DOT1X-3-INVALID_REPLAY_CTR: 1x_eapkey.c:360 Invalid replay counter from client 40:b3:95:13:da:cb - got 00 00 00 00 00 00 00 02, expected 00 00 00 00 00 00 00 04
*Dot1x_NW_MsgTask_0: Jan 11 01:03:31.648: #DOT1X-3-INVALID_REPLAY_CTR: 1x_eapkey.c:360 Invalid replay counter from client 24:77:03:67:01:48 - got 00 00 00 00 00 00 00 02, expected 00 00 00 00 00 00 00 03
*Dot1x_NW_MsgTask_5: Jan 11 01:03:31.638: #DOT1X-3-INVALID_REPLAY_CTR: 1x_eapkey.c:360 Invalid replay counter from client 14:10:9f:da:c1:cd - got 00 00 00 00 00 00 00 02, expected 00 00 00 00 00 00 00 03
*Dot1x_NW_MsgTask_2: Jan 11 01:03:31.638: #DOT1X-3-INVALID_REPLAY_CTR: 1x_eapkey.c:360 Invalid replay counter from client cc:78:5f:29:cc:82 - got 00 00 00 00 00 00 00 02, expected 00 00 00 00 00 00 00 03
*Dot1x_NW_MsgTask_4: Jan 11 01:03:31.633: #DOT1X-3-INVALID_REPLAY_CTR: 1x_eapkey.c:360 Invalid replay counter from client 08:11:96:55:81:c4 - got 00 00 00 00 00 00 00 02, expected 00 00 00 00 00 00 00 03
*Dot1x_NW_MsgTask_0: Jan 11 01:03:31.631: #DOT1X-3-INVALID_REPLAY_CTR: 1x_eapkey.c:360 Invalid replay counter from client 84:3a:4b:56:36:50 - got 00 00 00 00 00 00 00 02, expected 00 00 00 00 00 00 00 03
*Dot1x_NW_MsgTask_1: Jan 11 01:03:31.630: #DOT1X-3-INVALID_REPLAY_CTR: 1x_eapkey.c:360 Invalid replay counter from client 14:10:9f:e2:d4:91 - got 00 00 00 00 00 00 00 02, expected 00 00 00 00 00 00 00 03
*Dot1x_NW_MsgTask_0: Jan 11 00:59:52.593: #DOT1X-3-INVALID_REPLAY_CTR: 1x_eapkey.c:360 Invalid replay counter from client a0:88:b4:60:20:f8 - got 00 00 00 00 00 00 00 01, expected 00 00 00 00 00 00 00 02
*apfRogueTask_3: Jan 11 00:59:32.168: #APF-1-UNABLE_TO_CONTAIN_ROGUE: apf_rogue.c:4414 Unable to contain rogue 40:01:C6:11:F9:F1 - Not enough Container AP(s). Number of Container AP(s) 2, Requested containment level 4
*apfRogueTask_3: Jan 11 00:58:38.635: #APF-1-UNABLE_TO_CONTAIN_ROGUE: apf_rogue.c:4414 Unable to contain rogue 40:01:C6:11:F9:F1 - Not enough Container AP(s). Number of Container AP(s) 1, Requested containment level 4
*Dot1x_NW_MsgTask_0: Jan 11 00:50:06.885: #DOT1X-3-INVALID_REPLAY_CTR: 1x_eapkey.c:360 Invalid replay counter from client 10:68:3f:46:4e:e8 - got 00 00 00 00 00 00 00 01, expected 00 00 00 00 00 00 00 02
*Dot1x_NW_MsgTask_0: Jan 11 00:50:06.883: #DOT1X-3-INVALID_REPLAY_CTR: 1x_eapkey.c:360 Invalid replay counter from client 10:68:3f:46:4e:e8 - got 00 00 00 00 00 00 00 00, expected 00 00 00 00 00 00 00 02
*dot1xMsgTask: Jan 11 00:49:05.842: #DOT1X-3-PSK_CONFIG_ERR: 1x_ptsm.c:618 Client c8:e0:eb:19:2a:97 may be using an incorrect PSK
*apfRogueTask_3: Jan 11 00:40:42.576: #APF-1-UNABLE_TO_CONTAIN_ROGUE: apf_rogue.c:4414 Unable to contain rogue 40:01:C6:11:F9:F1 - Not enough Container AP(s). Number of Container AP(s) 3, Requested containment level 4
*Dot1x_NW_MsgTask_3: Jan 11 00:40:17.471: #DOT1X-3-INVALID_REPLAY_CTR: 1x_eapkey.c:360 Invalid replay counter from client c4:43:8f:f1:8c:8b - got 00 00 00 00 00 00 00 01, expected 00 00 00 00 00 00 00 02
*Dot1x_NW_MsgTask_4: Jan 11 00:40:03.368: #DOT1X-3-INVALID_REPLAY_CTR: 1x_eapkey.c:360 Invalid replay counter from client f0:d1:a9:8e:1a:dc - got 00 00 00 00 00 00 00 02, expected 00 00 00 00 00 00 00 03
*Dot1x_NW_MsgTask_1: Jan 11 00:39:30.528: #DOT1X-3-INVALID_REPLAY_CTR: 1x_eapkey.c:360 Invalid replay counter from client 14:10:9f:d8:84:09 - got 00 00 00 00 00 00 00 01, expected 00 00 00 00 00 00 00 02
I already go to this link to check the Description of errors-
http://www.cisco.com/en/US/docs/wireless/controller/message/guide/msgs4.html#wp1000139
Appreciate all feedback. Thank you.

Hi Ruben,
a) After successful dot1x authentication, session keys are derived from pairwise master key.
b) When the AP transmits a key to a station by default, it expects a response back within a set timeframe.
c) If the station does not respond, the AP increments the counter and retransmits the key.
d) If the AP receives a response to first message just after the retransmission of the key, a mismatch occurs in the counter.
This in most of the cases will be a client driver problem.
Solution :
1) try to increase the EAPOL-Key Timeout ( config advanced eap ).
2) Upgrade the client driver.
*****Help out other by using the rating system and marking answered questions as "Answered"*****

WLC 5508 WLAN SSID Problem

Similar Messages

Maybe you are looking for