WLC and Air 1231G

I have a 4402 WLC configured on the management VLAN and 9 AP's that were converted to LWAPP. When the AP's attempt to connect to the WLC, they download the image then display the following error. "No more AP manager IP addresses remain." The AP's then reboot and go through the whole process again. It doesn't matter if I assign static IP's or set them to DHCP, the same error appears.

I tried both suggestions without success. The same thing continues to happen.
Looking at the logs, I see that APs are associating then immediately disassociating. If it helps here are 15 minutes or so of message logs from the WLC.
Jun 04 09:11:04.996 spam_lrad.c:4306 LWAPP-3-HDR_ENCAP_ERR: Unable to encapsulate LWAPP header for discovery response; AP 00:24:14:11:50:c0
Jun 04 09:11:04.996 apf_net.c:807 APF-3-PDU_ENCAP_FAILED: Failed to encapsulate a PDU for transmission to station00:00:00:00:00:00. Destination IP address not set in L3 mode.
Jun 04 09:10:59.321 spam_lrad.c:4306 LWAPP-3-HDR_ENCAP_ERR: Unable to encapsulate LWAPP header for discovery response; AP 00:24:14:11:4c:00
Jun 04 09:10:59.321 apf_net.c:807 APF-3-PDU_ENCAP_FAILED: Failed to encapsulate a PDU for transmission to station00:00:00:00:00:00. Destination IP address not set in L3 mode.
Jun 04 09:10:57.869 spam_lrad.c:4306 LWAPP-3-HDR_ENCAP_ERR: Unable to encapsulate LWAPP header for discovery response; AP 00:24:14:11:4d:40
Jun 04 09:10:57.869 apf_net.c:807 APF-3-PDU_ENCAP_FAILED: Failed to encapsulate a PDU for transmission to station00:00:00:00:00:00. Destination IP address not set in L3 mode.
Jun 04 09:03:41.137 spam_lrad.c:4306 LWAPP-3-HDR_ENCAP_ERR: Unable to encapsulate LWAPP header for discovery response; AP 00:24:14:11:50:c0
Jun 04 09:03:41.137 apf_net.c:807 APF-3-PDU_ENCAP_FAILED: Failed to encapsulate a PDU for transmission to station00:00:00:00:00:00. Destination IP address not set in L3 mode.
Jun 04 09:03:35.676 spam_lrad.c:4306 LWAPP-3-HDR_ENCAP_ERR: Unable to encapsulate LWAPP header for discovery response; AP 00:24:14:11:4c:00
Jun 04 09:03:35.676 apf_net.c:807 APF-3-PDU_ENCAP_FAILED: Failed to encapsulate a PDU for transmission to station00:00:00:00:00:00. Destination IP address not set in L3 mode.
Jun 04 09:03:33.689 spam_lrad.c:4306 LWAPP-3-HDR_ENCAP_ERR: Unable to encapsulate LWAPP header for discovery response; AP 00:24:14:11:4d:40
Jun 04 09:03:33.689 apf_net.c:807 APF-3-PDU_ENCAP_FAILED: Failed to encapsulate a PDU for transmission to station00:00:00:00:00:00. Destination IP address not set in L3 mode.
Jun 04 08:57:44.898 acl.c:244 ACL-3-ENTRY_DONOT_EXIST: Unable to find an ACL by name "".
Jun 04 08:54:59.294 spam_radius.c:105 LWAPP-3-RADIUS_ERR: Could not send join reply, AP authorization failed; AP:00:24:14:11:4c:00
Jun 04 08:54:34.373 spam_radius.c:105 LWAPP-3-RADIUS_ERR: Could not send join reply, AP authorization failed; AP:00:24:14:11:50:c0
Jun 04 08:54:26.790 spam_radius.c:105 LWAPP-3-RADIUS_ERR: Could not send join reply, AP authorization failed; AP:00:24:14:11:4d:40
Jun 04 08:54:01.664 spam_radius.c:105 LWAPP-3-RADIUS_ERR: Could not send join reply, AP authorization failed; AP:00:24:14:11:4c:70
Jun 04 08:53:56.648 spam_radius.c:105 LWAPP-3-RADIUS_ERR: Could not send join reply, AP authorization failed; AP:00:24:14:11:4c:70
Jun 04 08:52:28.307 spam_radius.c:105 LWAPP-3-RADIUS_ERR: Could not send join reply, AP authorization failed; AP:00:24:14:11:50:c0
Jun 04 08:52:21.897 spam_radius.c:105 LWAPP-3-RADIUS_ERR: Could not send join reply, AP authorization failed; AP:00:24:14:11:4c:00
Jun 04 08:52:20.498 spam_radius.c:105 LWAPP-3-RADIUS_ERR: Could not send join reply, AP authorization failed; AP:00:24:14:11:4d:40
Jun 04 08:50:22.411 spam_radius.c:105 LWAPP-3-RADIUS_ERR: Could not send join reply, AP authorization failed; AP:00:24:14:11:50:c0
Jun 04 08:50:16.030 spam_radius.c:105 LWAPP-3-RADIUS_ERR: Could not send join reply, AP authorization failed; AP:00:24:14:11:4c:00
Jun 04 08:50:15.042 spam_radius.c:105 LWAPP-3-RADIUS_ERR: Could not send join reply, AP authorization failed; AP:00:24:14:11:4d:40
Jun 04 08:48:16.760 spam_radius.c:105 LWAPP-3-RADIUS_ERR: Could not send join reply, AP authorization failed; AP:00:24:14:11:50:c0

Similar Messages

WLAN Clients not browsing on Cisco Wireless Controller WLC NME-AIR-WLC12-K9

HiI have a question and i need a solution and expert help.I have done a deployment which involves Security (ASA5540), Routing/voice gateway/wlc NME-AIR-WLC12-k9) and Switching (Cisco3845-ccme/k9)Below is the list of equipment used:1. Cisco ASA 5540 - which is connected at the edge to the ISP router
2. Core Switch WS-C4948E as core and DHCP Server for all VLANs
3. Access/Distribution Switches WS-C3560G-48PS-S connected as trunk to the core switch
4. Router/Voice Gateway/WLC Cisco3845-CCME/K9 - This is the voice gateway and also the WLC
5. Wireless APs AIR-LAP1242AG-E-K9 (12 qty)Here is the deployment scenario:1. G0/0 of the ASA is connected to a 7200 router from the ISP (Public IP Add)
2. G0/1 of the ASA is connected to gig 1/3 on the Core Switch on VLAN 2 which is the management VLAN (Local IP 10.1.1.2)
3. Port 3 of the Core switch is on vlan 2 connected to ASA - Management IP of Core Switch is 10.1.1.1. Core Switch is the DHCP Server for all VLANS on the network.
4. All the Access/Distribution switches are configured with IP Addresses on VLAN 2
5. Telephony Services is configured on the router and DHCP Pool for Access Points and Wireless Clients is running on the router.
6. Two DHCP pools were created on the router for APs and Wireless Clients.
7. G0/0 of the router is configured on the same network that issues dhcp ip to the AP and is connected to gig 1/1 on the core switch
8 G0/1 of the router is configured as the voice port for the IP Telephony Services and is connected to G 1/2 on the core switch1. Clients receiving DHCP IP on the Core Switch can communicate with all vlans and can browse to the Internet.
2. IP Telephony Services is running well.
3. Client on wireless can get IP from the DHCP on the router but cannot browse.I have pings from the router to the core switch and firewall, but clients connected to the wireless
cannot ping other vlans on the core switch and vice versa.The port connecting the router to the core switch is an Access Port, i have changed to to trunk but still no changes.My biggest problem now is how to make the clients on the wireless communicate with other clients on the network and be able to browse to the Internet.Below is the configs on the router and core switch.Router ConfigNimc_Voice_Router#sh run
Building configuration...
Current configuration : 10513 bytes
! Last configuration change at 13:03:55 Nigeria Mon Nov 29 2010 by admin
! NVRAM config last updated at 13:03:56 Nigeria Mon Nov 29 2010 by admin
version 12.4
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname Nimc_Voice_Router
boot-start-marker
boot-end-marker
! card type command needed for slot/vwic-slot 0/2
logging message-counter syslog
enable secret
aaa new-model
! aaa authentication login default local
aaa session-id common
clock timezone Nigeria 1
dot11 syslog
ip source-route
ip dhcp excluded-address 10.1.12.1 10.1.12.10
ip dhcp excluded-address 192.168.1.1 192.168.1.10
ip dhcp pool LWAAP-AP
network 10.1.12.0 255.255.255.0
default-router 10.1.12.1
option 43 hex f104.c0a8.0002
dns-server 83.229.88.30 4.2.2.2 193.238.28.249
option 60 ascii "Cisco AP c1240"
ip dhcp pool Wireless
network 192.168.1.0 255.255.255.0
default-router 192.168.1.1
dns-server 83.229.88.30 193.238.28.249 4.2.2.2
ip cef
no ip domain lookup
ip domain name nimc.gov.ng
ip name-server 83.229.88.30
ip name-server 193.238.28.249
ip name-server 4.2.2.2
no ipv6 cef
multilink bundle-name authenticated
voice-card 0
archive
log config
hidekeys
interface GigabitEthernet0/0
description Connection to AP
ip address 10.1.12.1 255.255.255.0
ip helper-address 192.168.0.2
load-interval 30
duplex auto
speed auto
media-type rj45
interface Service-Engine0/0
no ip address
shutdown
interface GigabitEthernet0/1
ip address 10.1.2.2 255.255.255.0
duplex auto
speed auto
media-type rj45
interface FastEthernet0/0/0
no ip address
shutdown
duplex auto
speed auto
interface Serial0/1/0
no ip address
shutdown
no fair-queue
clock rate 2000000
interface Serial0/1/1
no ip address
shutdown
clock rate 2000000
interface Integrated-Service-Engine1/0
ip address 192.168.0.1 255.255.255.0
no keepalive
interface Integrated-Service-Engine1/0.15
encapsulation dot1Q 15
ip address 192.168.1.1 255.255.255.0
interface Integrated-Service-Engine1/0.100
encapsulation dot1Q 100
ip forward-protocol nd
ip forward-protocol udp 12223
ip route 10.1.0.0 255.255.255.0 10.1.1.1
ip route 10.1.1.0 255.255.255.0 10.1.1.1
ip route 10.1.2.0 255.255.255.0 10.1.1.1
ip route 10.1.3.0 255.255.255.0 10.1.1.1
ip route 10.1.4.0 255.255.255.0 10.1.1.1
ip route 10.1.5.0 255.255.255.0 10.1.1.1
ip route 10.1.6.0 255.255.255.0 10.1.1.1
ip route 10.1.7.0 255.255.255.0 10.1.1.1
ip route 10.1.8.0 255.255.255.0 10.1.1.1
ip route 10.1.9.0 255.255.255.0 10.1.1.1
ip route 10.1.10.0 255.255.255.0 10.1.1.1
ip route 10.1.11.0 255.255.255.0 10.1.1.1
ip route 10.1.12.0 255.255.255.0 10.1.1.1
ip route 192.168.0.0 255.255.255.0 10.1.1.1
ip route 192.168.1.0 255.255.255.0 10.1.1.1
no ip http server
ip http secure-server
!Core Switch Configsh run
Building configuration...Current configuration : 10622 bytes
version 12.2
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
service compress-config
hostname Nimc_Core
boot-start-marker
boot-end-marker!
aaa new-model
aaa authentication login default local
aaa session-id common
storm-control broadcast include multicast
ip subnet-zero
no ip domain-lookup
ip domain-name nimc.gov.ng
ip dhcp excluded-address 10.1.2.1 10.1.2.10
ip dhcp excluded-address 10.1.4.1 10.1.4.10
ip dhcp excluded-address 10.1.5.1 10.1.5.10
ip dhcp excluded-address 10.1.6.1 10.1.6.10
ip dhcp excluded-address 10.1.7.1 10.1.7.10
ip dhcp excluded-address 10.1.8.1 10.1.8.10
ip dhcp excluded-address 10.1.9.1 10.1.9.10
ip dhcp excluded-address 10.1.10.1 10.1.10.10
ip dhcp excluded-address 10.1.3.1 10.1.3.10
ip dhcp pool Voice
network 10.1.2.0 255.255.255.0
next-server 10.1.2.1
option 150 ip 10.1.2.2
default-router 10.1.2.1
dns-server 83.229.88.30 193.238.28.249 4.2.2.2
ip dhcp pool SF_DGs_Office
network 10.1.3.0 255.255.255.0
domain-name nimc.gov.ng
default-router 10.1.3.1
dns-server 81.199.3.7
lease 10
ip dhcp pool Admin_Process_Fac_Mgt
network 10.1.4.0 255.255.255.0
domain-name nimc.gov.ng
default-router 10.1.4.1
dns-server 83.229.88.30 193.238.28.249 4.2.2.2
lease 10
ip dhcp pool SF_IDD
network 10.1.5.0 255.255.255.0
domain-name nimc.gov.ng
default-router 10.1.5.1
dns-server 83.229.88.30 193.238.28.249 4.2.2.2
lease 10
ip dhcp pool Finance_Fin_Inv
network 10.1.6.0 255.255.255.0
domain-name nimc.gov.ng
default-router 10.1.6.1
dns-server 83.229.88.30 193.238.28.249 4.2.2.2
lease 10
ip dhcp pool Finance_CS
network 10.1.7.0 255.255.255.0
domain-name nimc.gov.ng
default-router 10.1.7.1
dns-server 83.229.88.30 193.238.28.249 4.2.2.2
lease 10
ip dhcp pool FF_Human_Capital_Mgt
network 10.1.8.0 255.255.255.0
domain-name nimc.gov.ng
default-router 10.1.8.1
dns-server 83.229.88.30 193.238.28.249 4.2.2.2
lease 10
ip dhcp pool FF_Legal_Services
network 10.1.9.0 255.255.255.0
domain-name nimc.gov.ng
default-router 10.1.9.1
dns-server 83.229.88.30 193.238.28.249 4.2.2.2
lease 10
ip dhcp pool SF_Procurement_Serv
network 10.1.10.0 255.255.255.0
domain-name nimc.gov.ng
default-router 10.1.10.1
dns-server 83.229.88.30 193.238.28.249 4.2.2.2
lease 10
ip vrf mgmtVrf
errdisable recovery cause bpduguard
errdisable recovery interval 180
power redundancy-mode redundant
spanning-tree mode mst
spanning-tree portfast bpduguard default
spanning-tree extend system-id
spanning-tree mst configuration
name xxxx
revision 1
instance 1 vlan 1-20
spanning-tree mst 1 priority 0
spanning-tree vlan 1-20 priority 0
vlan internal allocation policy ascending
interface FastEthernet1
ip vrf forwarding mgmtVrf
no ip address
speed auto
duplex auto
interface GigabitEthernet1/1
switchport trunk encapsulation dot1q
switchport mode trunk
interface GigabitEthernet1/2
switchport access vlan 4
switchport mode access
spanning-tree portfast
interface GigabitEthernet1/3
switchport access vlan 2
switchport mode access
switchport voice vlan 4
spanning-tree portfast
interface GigabitEthernet1/4
switchport mode access
spanning-tree portfast
interface GigabitEthernet1/5
switchport access vlan 2
switchport mode access
switchport voice vlan 4
spanning-tree portfast
interface GigabitEthernet1/6
switchport access vlan 2
switchport mode access
switchport voice vlan 4
spanning-tree portfast
interface GigabitEthernet1/7
switchport access vlan 2
switchport mode access
switchport voice vlan 4
spanning-tree portfast
interface GigabitEthernet1/8
switchport access vlan 2
switchport mode access
switchport voice vlan 4
spanning-tree portfast!
interface GigabitEthernet1/9
switchport access vlan 2
switchport mode access
switchport voice vlan 4
spanning-tree portfast
interface GigabitEthernet1/10
switchport access vlan 2
switchport mode access
switchport voice vlan 4
spanning-tree portfast
interface GigabitEthernet1/11
switchport access vlan 2
switchport mode access
switchport voice vlan 4
spanning-tree portfast
interface GigabitEthernet1/12
switchport access vlan 2
switchport mode access
switchport voice vlan 4
spanning-tree portfast
interface GigabitEthernet1/13
switchport access vlan 2
switchport mode access
switchport voice vlan 4
spanning-tree portfast
interface GigabitEthernet1/14
switchport access vlan 2
switchport mode access
switchport voice vlan 4
spanning-tree portfast
interface GigabitEthernet1/15
switchport access vlan 2
switchport mode access
switchport voice vlan 4
spanning-tree portfast
interface GigabitEthernet1/16
switchport access vlan 2
switchport mode access
switchport voice vlan 4
spanning-tree portfast
interface GigabitEthernet1/17
switchport access vlan 2
switchport mode access
switchport voice vlan 4
spanning-tree portfast
interface GigabitEthernet1/18
switchport access vlan 2
switchport mode access
switchport voice vlan 4
spanning-tree portfast
interface GigabitEthernet1/19
switchport access vlan 2
switchport mode access
switchport voice vlan 4
spanning-tree portfast
interface GigabitEthernet1/20
switchport access vlan 2
switchport mode access
switchport voice vlan 4
spanning-tree portfast
interface GigabitEthernet1/21
switchport access vlan 2
switchport mode access
switchport voice vlan 4
spanning-tree portfast
interface GigabitEthernet1/22
switchport access vlan 2
switchport mode access
switchport voice vlan 4
spanning-tree portfast
interface GigabitEthernet1/23
switchport access vlan 2
switchport mode access
switchport voice vlan 4
spanning-tree portfast
interface GigabitEthernet1/24
switchport access vlan 2
switchport mode access
switchport voice vlan 4
spanning-tree portfast
interface GigabitEthernet1/25
switchport access vlan 2
switchport mode access
switchport voice vlan 4
spanning-tree portfast
interface GigabitEthernet1/26
switchport access vlan 2
switchport mode access
switchport voice vlan 4
spanning-tree portfast
interface GigabitEthernet1/27
switchport access vlan 2
switchport mode access
switchport voice vlan 4
spanning-tree portfast
interface GigabitEthernet1/28
switchport access vlan 2
switchport mode access
switchport voice vlan 4
spanning-tree portfast
interface GigabitEthernet1/29
switchport access vlan 2
switchport mode access
switchport voice vlan 4
spanning-tree portfast
interface GigabitEthernet1/30
switchport access vlan 2
switchport mode access
switchport voice vlan 4
spanning-tree portfast
interface GigabitEthernet1/31
switchport access vlan 2
switchport mode access
switchport voice vlan 4
spanning-tree portfastinterface GigabitEthernet1/32
switchport access vlan 2
switchport voice vlan 4
interface GigabitEthernet1/33
switchport mode access
interface GigabitEthernet1/34
switchport access vlan 2
switchport mode access
switchport voice vlan 4
spanning-tree portfast
interface GigabitEthernet1/35
switchport access vlan 2
switchport mode access
switchport voice vlan 4
spanning-tree portfast
interface GigabitEthernet1/36
switchport access vlan 2
switchport mode access
switchport voice vlan 4
spanning-tree portfast
interface GigabitEthernet1/37
switchport access vlan 2
switchport mode access
switchport voice vlan 4
spanning-tree portfast
interface GigabitEthernet1/38
switchport access vlan 2
switchport mode access
switchport voice vlan 4
spanning-tree portfast
interface GigabitEthernet1/39
switchport access vlan 2
switchport mode access
switchport voice vlan 4
spanning-tree portfast
interface GigabitEthernet1/40
switchport access vlan 2
switchport mode access
switchport voice vlan 4
spanning-tree portfast
interface GigabitEthernet1/41
switchport access vlan 2
switchport mode access
switchport voice vlan 4
spanning-tree portfast
interface GigabitEthernet1/42
switchport access vlan 2
switchport mode access
switchport voice vlan 4
spanning-tree portfast
interface GigabitEthernet1/43
switchport access vlan 2
switchport mode access
switchport voice vlan 4
spanning-tree portfast
interface GigabitEthernet1/44
switchport access vlan 2
switchport mode access
switchport voice vlan 4
spanning-tree portfast
interface GigabitEthernet1/45
switchport access vlan 2
switchport mode access
switchport voice vlan 4
spanning-tree portfast
interface GigabitEthernet1/46
switchport access vlan 2
switchport mode access
switchport voice vlan 4
spanning-tree portfast
interface GigabitEthernet1/47
switchport trunk encapsulation dot1q
switchport mode trunk
interface GigabitEthernet1/48
switchport trunk encapsulation dot1q
switchport mode trunk
interface Vlan1
no ip address
shutdown
interface Vlan2
description Management
ip address 10.1.1.1 255.255.255.0
interface Vlan3
description Enterprise
ip address 10.1.0.1 255.255.255.0
interface Vlan4
description Voice
ip address 10.1.2.1 255.255.255.0
interface Vlan5
description SS_DGs_Office
ip address 10.1.3.1 255.255.255.0
interface Vlan6
description Admin_Process_Fac_Management
ip address 10.1.4.1 255.255.255.0
interface Vlan7
description SF_National_Identity_Database
ip address 10.1.5.1 255.255.255.0
interface Vlan8
description Fin_Finance_Investment
ip address 10.1.6.1 255.255.255.0
interface Vlan9
description Fin_Corporate_Services
ip address 10.1.7.1 255.255.255.0
interface Vlan10
description FF_Human_Capital_Management
ip address 10.1.8.1 255.255.255.0
interface Vlan11
description FF_Legal_services
ip address 10.1.9.1 255.255.255.0
interface Vlan12
description SF_Procurement_Services
ip address 10.1.10.1 255.255.255.0
ip default-gateway 10.1.1.2
ip route 0.0.0.0 0.0.0.0 10.1.1.2
ip route 10.1.1.0 255.255.255.0 10.1.1.2
ip route 10.1.2.0 255.255.255.0 10.1.1.2
ip route 10.1.3.0 255.255.255.0 10.1.1.2
ip route 10.1.4.0 255.255.255.0 10.1.1.2
ip route 10.1.5.0 255.255.255.0 10.1.1.2
ip route 10.1.6.0 255.255.255.0 10.1.1.2
ip route 10.1.7.0 255.255.255.0 10.1.1.2
ip route 10.1.8.0 255.255.255.0 10.1.1.2
ip route 10.1.9.0 255.255.255.0 10.1.1.2
ip route 10.1.10.0 255.255.255.0 10.1.1.2
ip route 10.1.11.0 255.255.255.0 10.1.1.2
ip http server
--More--
control-plane
line con 0
stopbits 1
line vty 0 4
end
Please i need somebody to help me

I wouldn't configure an ip address on the service engine subinterface.
Try setting up a vlan interface on the router with that ip address and the subinterface will be linked to the vlan interface through the encapsulation command. A vlan interface will better work as a gateway for the wireless clients
Nicolas

WLC and WCS conflict

Hi I am currently using 21 X WLC with N+1 Redundancy and 1X WCS with 1000++ of LAP1020. If had been observed that the antenna type and power TX had been changed with no reason. Is there any settings that may affect with AP customized Tx Power and antenna settings other than using the WCS template to push the configure to the APs instead of the WLC.

Sorry for jumping in on the question with another question but it seemed the right place.
I have an AIR-CT5508-25-K9 WLC and +25AP license : L-LIC-CT5508-25A.
As far as I understand it the WLC should already have a 25AP license installed and with the adder license I should have a count of 50 APs.
However, after installing the adder license the count is still 25.
Could you please let me know if it's just something wrong in my reasoning or should a case be opened?
Thank you,
Barbara

WLC 4402 with 1231g

Hi!
I got a problem with a LWAPP 1231 and 4402 WLC. The convertion procedure goes fine, but when the AP tries to join to controller i find some errors on the AP and does not register on the WLC.
Errors on the AP:
*Mar 1 00:00:23.718: %LWAPP-5-CHANGED: LWAPP changed state to DISCOVERY
Mar 1 00:00:34.383: %LWAPP-5-CHANGED: LWAPP changed state to JOIN
Mar 1 00:00:40.395: LWAPP_CLIENT_ERROR_DEBUG: spamHandleJoinTimer: Did not rec
ieve the Join response
*Mar 1 00:00:40.395: LWAPP_CLIENT_ERROR_DEBUG: No more AP manager IP addresses remain.
Mar 1 00:00:40.447: %SYS-5-RELOAD: Reload requested by LWAPP CLIENT. Reload Reason: DID NOT GET JOIN RESPONSE.
*Mar 1 00:00:40.447: %LWAPP-5-CHANGED: LWAPP changed state to DOWNXmodem file s
ystem is available.
WLC version: AIR-WLC4400-K9-4-2-112-0.aes
AP version: c1200-rcvk9w8-tar.123-11JX1.tar
Hope it helps.
Thank you very much

Check out these other threads:
http://forum.cisco.com/eforum/servlet/NetProf?page=netprof&forum=Wireless%20-%20Mobility&topic=General&CommCmd=MB%3Fcmd%3Dpass_through%26location%3Doutline%40%5E1%40%40.2cc09a8d
http://forum.cisco.com/eforum/servlet/NetProf?page=netprof&forum=Wireless%20-%20Mobility&topic=Getting%20Started%20with%20Wireless&CommCmd=MB%3Fcmd%3Dpass_through%26location%3Doutline%40%5E1%40%40.2cc0cd51

2106 WLC and 4 LWAPP (1252G)

I have a 2106 WLC with 4 AP's (AIR-LAP1252AG-A-K9)
One of the AP's (port 4) is only connecting at 10Mbps, not 100Mbps and I don't know why?
All the ;ports are set on the controller to AUTO, When I try to force that port to 100Mbps, the link drops.
Could it be a cabling issue... or could I have a bad port on the 2106?    How to I troubleshoot this. It's odd, because
that particular AP is about 100ft from thte WLC and the closest to it.
Any ideas?
Joe
Primary Software Version   7.0.116.0
Predownload Retry Count
Boot Version   12.4.18.1
IOS Version   12.4(23c)JA2
Mini IOS Version 3.0.51.0
Primary Software Version   7.0.116.0
Predownload Retry Count
Boot Version   12.4.18.1
IOS Version   12.4(23c)JA2
Mini IOS Version 3.0.51.0

Interesting... I unplugged the LAP (data and power) and removed it from the wall of our training room 75ft from our computer room, walked the AP into the computer room and with a 15' patch cord and power supply plugged it back into the WLC 2106. Waited a min for the AP to reboot and now my port speed is showing 100Mbps connection.
The issue must be with the cable run...? Thanks for pointing out the obvious.   This now begs another questions regarding 2106 best practices and the idea of connecting our 4 AP's directly into network switches and not the WLC 2106 itself. That seems to be the recommendation. Any comments?
Joe

WLC and WCS licenses

How many APs does wireless controller 5508 and WCS (version 7.0) supports?
Cheers,

Sorry for jumping in on the question with another question but it seemed the right place.
I have an AIR-CT5508-25-K9 WLC and +25AP license : L-LIC-CT5508-25A.
As far as I understand it the WLC should already have a 25AP license installed and with the adder license I should have a count of 50 APs.
However, after installing the adder license the count is still 25.
Could you please let me know if it's just something wrong in my reasoning or should a case be opened?
Thank you,
Barbara

5760 WLC and 5760 HA WLC question

Hi everyone,
I assume this information must exist... I just cannot locate it. Customer purchasing two 5760 WLCs:
1     AIR-CT5760-500-K9
1     AIR-CT5760-HA-K9
I am looking for info on how to configure these 2 WLCs to work together. How do you inform the production WLC that a HA WLC is available to sync with? Do WLCs have to be L-2 adjacent, or will HA operate at L-3? How does this HA setup work? etc.
Any help would be really appreciated.

Hi,
Any news regarding this issue?
We've have the same scenario:
1     AIR-CT5760-500-K9
1     AIR-CT5760-HA-K9
Both running
IOS XE 03.03.01SE
I've activated Global AP Failover Priority in both WLC and from a total of 47 APs, i've configured 8 with Priority Critical, 7 APs with Priority High and 3 APs with Priority Medium.
We've issued an reload to the primary WLC and it took 7 minutes for the APs recover from the Secondary to the Primary
13:14 - reload issued on the primary WLC
13:15 - service granted by the secondary WLC (required an shut/no shut to the "Network Status" of the radio interfaces)
13:22 - service recovered to the primary WLC
Edit - Forgot to mention that the priority values mentioned above didn't show much improvement in the AP recovery time...

The difference between AIR-ANT5135D-R and AIR-ANT5135DB-R

Hi,
Anyone know what is the difference between AIR-ANT5135D-R and AIR-ANT5135DB-R ?
From the dynamic configuration tools for 1252 and 1242, AIR-ANT2422DB-R is inside one of the antenna option.
However, I can't find it in the "Cisco Aironet Antennas and Accessories Reference Guide"
http://www.cisco.com/en/US/prod/collateral/wireless/ps7183/ps469/product_data_sheet09186a008008883b.html
Inside the document there is only AIR-ANT5135D-R.
likewise for the 2.4 GHz, AIR-ANT2422DB-R is inside the dynamic configuration tools and not inside "Cisco Aironet Antennas and Accessories Reference Guide"
Any help would be appreciated
Thanks,
Richard

Found the difference, AIR-ANT5135DB-R and AIR-ANT2422DB-R are non-articulating antennas.
Thanks!
Richard

Purchase Order Dashboard using Adobe Flex and AIR

Hi ,
I have written a AIR apps for displaying the Purchase Order using OPen source Flex and AIR making Web Service calls to our SAP R3 6.20 Backend System . If anybody would be interested in taking a look at it and expanding the apps please free to post at those forum with the your email ID . I can send the AIR apps along with the source code .
Thnks
V

I have uploaded the zip file containing my code . If anybody is interested can download from this link .
http://www.mediafire.com/?8mfesdczsuv
Vinod

Hi, I'm using a Mac Pro here. I am trying to connect it with my NAS hard drive. But i could not connect to it because i have an ethernet which connects to the intranet in my company and Air Port for the internet.

Hi, I'm using a Mac Pro here. I am trying to connect it with my NAS hard drive. But i could not connect to it because i have an ethernet which connects to the intranet in my company and Air Port for the internet and it could not detect the the ip address after i input the correct address on "Connect to Server" window. Please help! Urgent! Thanks

I did not say it is not possible.
I said if your company networks are monopolizing both ports, you should talk to them about what options are available.
Maybe you can get the company Intranet over wireless if you change some configuration items such as Subnet Mask.
Maybe you can get on the Internet over Ethernet.
You really need to ask them, and do not let them blow you off because you have a Mac. If they balk, ask them how it would be done on a PC (becasue it will be the same on a Mac).

Iphoto continually quit on MBP and Air, now won't reinstall on Air

I have a MBP and Air with ilife 08 and all the latest apple software updates on each.
For about three weeks iphoto has been shutting down on either computer whenever i email a photo, or download and save a photo from the internet.
Today i removed iphoto from both computers and reinstalled.
After reinstalling my MBP it seemed to work fine, only shutting down once in about 15 emailed photos (as compared to every time previosuly). Thinking all was well (or at least acceptible) I went ahead and installed the three updates from apple via the software updater in system preferences. After i installed the automatic updates and used iphoto again, it shut down every time i emailed a photo. At that point I uninstalled the iphoto and reinstalled it without the latest apple updates. It seems to work fine now.
So, I tried doing the same thing on my air, but now iphoto won't reinstall, even though each time at the end of the process it tells me the install was successful. The first two times I only uninstalled (dragged to trash) iphoto, but the next two times i also dumped garageband, iweb, and idvd. Each time these programs were reinstalled, but not iphoto. When I search on iphoto no results.
Any ideas on how to get iphoto back on my air? I am using remote disk and have never had any previous problems with it, and obviously the other programs reinstalled fine.
Thoughts on why iphoto won't work with the latest apple updates installed?

fishbio:
Before reinstalling iPhoto make sure you've deleted all files with iPhoto in the file name that reside in the HD/Library/Receipts folder. Otherwise the installer will think that iPhoto already exists and doesn't need to install.
TIP: For insurance against the iPhoto database corruption that many users have experienced I recommend making a backup copy of the Library6.iPhoto (iPhoto.Library for iPhoto 5 and earlier) database file and keep it current. If problems crop up where iPhoto suddenly can't see any photos or thinks there are no photos in the library, replacing the working Library6.iPhoto file with the backup will often get the library back. By keeping it current I mean backup after each import and/or any serious editing or work on books, slideshows, calendars, cards, etc. That insures that if a problem pops up and you do need to replace the database file, you'll retain all those efforts. It doesn't take long to make the backup and it's good insurance.
I've created an Automator workflow application (requires Tiger), iPhoto dB File Backup, that will copy the selected Library6.iPhoto file from your iPhoto Library folder to the Pictures folder, replacing any previous version of it. It's compatible with iPhoto 6 and 7 libraries and Tiger and Leopard. iPhoto does not have to be closed to run the application, just idle. You can download it at Toad's Cellar. Be sure to read the Read Me pdf file.

Flex SDK and AIR runtime version in mobile

Hi, guys.
I'm trying to make my first Flex mobile app.
I'm a little confused about the relationship between Flex SDK and AIR runtime versions for mobile development.
In the "Developing Mobile Applications with ADOBE FLEX 4.6 and ADOBE FLASH BUILDER 4.6" pdf document, it says:
"AIR requirements
Flex mobile projects and ActionScript mobile projects require AIR 2.6 or a higher version. You can run mobile projects on physical devices that support AIR 2.6 or a higher version of AIR.
You can install AIR 2.6 or a higher version only on supported Android devices that run Android 2.2 or a higher version. For the complete list of supported Android devices, see Certified Devices. Also, review the minimum system requirements to run Adobe AIR on Android devices at Mobile System Requirements.
Note: If you do not have a device that supports AIR 2.6 or a higher version of AIR, you can use Flash Builder to launch and debug mobile applications on the desktop."
So, I go and check the Certified devices in http://www.adobe.com/devnet-apps/flashruntimes/certified-devices.html and find that the minimun FLASH PLAYER version accepted by ALL devices is FP 10.1
1. Does this mean that if I want to release an app to target ALL mobile devices, then I can only use Flex 4.5?
2. Do support for Flash Player mean the same than support for Adobe AIR? Or the application will prompt the user to install whatever version of the AIR runtime and all of them would be supported by the device, even in the FLASH PLAYER support is for a lesser version?
Thanks!

Thanks for your help, Flex harUI,
The first impression that comes to mind is that FP version is indeed only for the web browser plugin. Then, why does the official Flex 4.6 mobile development documentation have a link to that page that only speaks about the supported FP version in mobiles under the title "AIR requirements"??
This makes it way too confusing.
Do you know whether there is something like an equivalent matrix/list of mobile devices with their supported AIR runtime versions? I went a great deal in trying to keep my original app under 400kb... I didn't know that in the end it would end up weighing 9.5Mb... :S
Thanks again,

I downloaded the iOS7 system and lost connectivity to my in-ceiling speakers and Air Play. How do I get it back?

I downloaded the iOS7 system and lost connectivity to my in-ceiling speakers and Air Play. How do I get it back?

Use the iOS7 Control Center to select AirPlay, and then, choose the appropriate AirPlay speaker to stream to.

ISE 1.2 With WLC and AD

Hi everyone,
What is the steps and Procedure implement Wired and wireless authentication with ISE, WLC and AD for a LAB environment. currently the following are done.
The wireless network is configured with 2 SSID (Staff and Guest)
Active Directory, DNS, DHCP, and NTP configured & synced.
ISE and AD running on C220 VMs, and WLC is 5760 Appliance.
Please provide your thoughts and assistance.
Regards

You have to implement dot1x and radius between your NAD and ISE device.
Using the switch 3850, that are the steps:
username RADIUS-HEALTH password radiusKey1 privilege 15
aaa new-model
aaa authentication login default local
aaa authentication dot1x default group radius
aaa authorization network default group radius
aaa authorization auth-proxy default group radius
aaa accounting update periodic 5
aaa accounting auth-proxy default start-stop group radius
aaa accounting dot1x default start-stop group radius
!this password will be used to communicate with ISE and to verify reachability
!between ISE and Switch
aaa server radius dynamic-author
client 172.16.1.18 server-key 7 radiuskey
client 172.16.1.20 server-key 7 radiuskey
ip domain-name lab.local
ip name-server 172.16.1.1
dot1x system-auth-control
interface GigabitEthernet1/0/3
switchport mode access
switchport voice vlan 50
switchport access vlan 10
ip access-group ACL-ALLOW in
authentication event fail action next-method
authentication event server dead action authorize voice
authentication event server alive action reinitialize
authentication host-mode multi-auth
authentication open
authentication order dot1x mab
authentication priority dot1x mab
authentication port-control auto
authentication periodic
authentication timer reauthenticate server
authentication violation restrict
mab
dot1x pae authenticator
dot1x timeout tx-period 10
spanning-tree portfast
ip access-list extended ACL-ALLOW
permit ip any any
!the comm between radius and ise will occur on these Port
ip radius source-interface Vlan100
logging origin-id ip
logging source-interface Vlan100
logging host 172.16.1.20 transport udp port 20514
logging host 172.16.1.18 transport udp port 20514
ip radius source-interface Vlan100
logging origin-id ip
logging source-interface Vlan100
logging host 172.16.1.20 transport udp port 20514
logging host 172.16.1.18 transport udp port 20514
snmp-server community ciscoro RO
snmp-server community public RO
snmp-server trap-source Vlan100
snmp-server source-interface informs Vlan100
radius-server attribute 6 on-for-login-auth
radius-server attribute 8 include-in-access-req
radius-server attribute 25 access-request include
radius-server dead-criteria time 10 tries 3
radius-server vsa send accounting
radius-server vsa send authentication
!defining ISE servers
radius server ISE-RADIUS-1
address ipv4 172.16.1.20 auth-port 1812 acct-port 1813
automate-tester username RADIUS-HEALTH idle-time 15
key radiusKey
Please be sure that NTP servers and time are synchronized.
enable dot1X on windows machine, or using cisco NAM.
you can enable debugging on aaa authentication to see the events.
you have to create this user on ISE (RADIUS-HEALTH).
3850#test aaa group radius username password new-code
and observe the result. You are supposed to have user authenticated successfully.
You Must also have define these device in ISE on the radius interface.
ip radius source-interface ..... use this interface ip address to define Ip address of the NAD device in ISE.
administration-->network resources -->Network Devices-->Add
input the name
input the Ip address for radius communication
select the authentication settings and field the corresponding shared secret radius key
select snmp settings and select version 2c.
snmp community : ciscoro
you can customize the polling interval if you want and that all.
you are supposed to received message communication between your NAD and ISE.
After you can do the procedure for WLC device.
I will fill it after you have passed the first steps (3850 authentication).

What is best blue tooth presenter for macbook pro and air

What is best Blue Tooth presenter for MacBook Pro and Air?

You got lots of choices such as:
WD Studio
http://www.wdc.com/en/products/products.aspx?id=200
WD Studio 2
http://www.wdc.com/en/products/products.aspx?id=210
WD My Book
http://www.wdc.com/en/products/products.aspx?id=250
Lacie:
http://www.lacie.com/dk/products/range.htm?id=10007
http://www.lacie.com/dk/products/range.htm?id=10036
The are tons of external storage for mac out there but these are a few of them...
I personally like the WD Studio 2 and the LaCie 2big Network 2

WLC and Air 1231G

Similar Messages

Maybe you are looking for