WLC failed to connect to WCS by snmp

Hi fellows,
I've a solution implemented that contains 1 WCS and 3 WLC.
For some unknown reason, started from some point, one of the WLC started to fail to connect by snmp to the WCS, given the next error "
%AAA-3-LDAP_CONNECT_SERVER_FAILED: ldap_db.c:1037 Could not connect to LDAP server 2, reason: 49 (Invalid credentials)."
I've made upgrade for the last version of firmware on all WLC's, have rewritten the credentials of SNMP, but the problem remains with only one of the WLC's, all others are working fine.
The SNMP is v.3.
The version of WCS is 6.0.132.0.
Any ideias?
Best regards,
Luis Matos

Hi Scott Fella,
Thanks for your answer.
When the problem appears, the version of the wlc was 6.0.182. We 've made upgrade to version 7.0.116.0 to try to resolve the problem, but the problem remains.
The 2 others WLC that is working fine, have the version 6.0.182.
There isn't any FW between the WLC's and WCS.
Best Regards,
Luis Matos

Similar Messages

WLC 5508 - Failed to connect from LMS 3.2

Hello.
I am trying to include a WLC 5508 in our LMS 3.2.
I have defined the device and credentials, but the LMS server cannot get access to it.
If I try to check de device credentials from the Device Center I get a "failed to connect", but if I a try a telnet session, also from Device Center, I get a connection.
I checked the credentails are OK.
Thank you.

Hi,
You need to download and install the last package : WLC.RME431.v2-1.zip : http://www.cisco.com/cisco/software/cart.html?imageGuId=E3A42793DA29A1B6AC3024C088F9FBC2B324EC8B&i=rs
You must install : MDF 1.37
You must install packages before WLC.RME431.v2-1.zip:
SharedSwimWLC.RME431.v1-2.zip
SharedDcmaWLC.RME431.v1-1.zip
SharedSwimIOS.RME431.v2-5-4.zip
LibSwim.RME431.v2-5-3.zip
LibCommon.RME431.v2-4-2.zip
Elisabeth
WLC.RME431.v2-1.readme:
Supported Devices
=================
Device Type : Cisco 5500 Series Wireless LAN Controllers
Cisco 3750 Switch with Wireless LAN Controller
Devices/Modules Supported :
Cisco 5508 Wireless LAN Controller : 1.3.6.1.4.1.9.1.1069
Cisco 3750 24+2 port 10/100/1000 Switch with integrated Cisco 4402 Wireless Controller: 1.3.6.1.4.1.9.1.747
Features Supported:
Inventory Manager : Yes
Syslog Analyzer : Yes
Config.Mgmt : Yes
Software Mgmt : Yes
Minimum Software : 6.0.188.0
Hardware and Software Requirements
==================================
Hardware and software requirements are the same as those needed for Resource Manager
Essentials 4.3.1 installation.
You must install Resource Manager Essentials 4.3.1 and MDF 1.37 before installing the
device package.
For a detailed list of requirements, as well as instructions for installing Resource
Manager Essentials 4.3.1, go to Cisco.com.
For documentation on Resource Manager Essentials, see:
http://www.cisco.com/en/US/products/sw/cscowork/ps2073/tsd_products_support_series_home.html
Package Dependencies
====================
To install the WLC Package, you must install the
following dependent packages:
SharedSwimWLC.RME431.v1-2.zip
SharedDcmaWLC.RME431.v1-1.zip
SharedSwimIOS.RME431.v2-5-4.zip
LibSwim.RME431.v2-5-3.zip
LibCommon.RME431.v2-4-2.zip

[Fail] - failed to connect stream: invalid argument? pulseaudio

I have pulseaudio installed and i am trying with gstreamer its always failing. But this works when i try with Fedora live cd or Ubuntu live cd. But Archlinux failing.
GOAL: (to make this work)
======
$ gst-launch pulsesrc device="alsa_input.pci-0000_00_1b.0.analog-stereo" ! alsasink device=hw:0,0
Setting pipeline to PAUSED ...
ERROR: Pipeline doesn't want to pause.
ERROR: from element /GstPipeline:pipeline0/GstPulseSrc:pulsesrc0: Failed to connect stream: Invalid argument
Additional debug info:
pulsesrc.c(1480): gst_pulsesrc_prepare (): /GstPipeline:pipeline0/GstPulseSrc:pulsesrc0
Setting pipeline to NULL ...
Freeing pipeline ...
TRY 1: fail
======
$ pulseaudio -k; pulseaudio --daemonize=no -vvvvvvvvv ;
----- starts fine ---------
$ pacmd dump | grep alsa_input
set-source-volume alsa_input.pci-0000_00_1b.0.analog-stereo 0x8050
set-source-mute alsa_input.pci-0000_00_1b.0.analog-stereo no <<< this one
suspend-source alsa_input.pci-0000_00_1b.0.analog-stereo yes
set-default-source alsa_input.pci-0000_00_1b.0.analog-stereo
; alsa works fine
$ alsactl init Found hardware: "HDA-Intel" "Intel CougarPoint HDMI" "HDA:10ec0892,10280527,00100302 HDA:80862805,58862805,00100000" "0x1028" "0x0527" Hardware is initialized using a generic method
TRY 2: fail
=====
if [ ! -d "/etc/asound.conf" ]; then
cat > /etc/asound.conf << \EOF
pcm.pulse {
type pulse
ctl.pulse {
type pulse
pcm.!default {
type pulse
ctl.!default {
type pulse
EOF
fi
or
pcm.!default { type plug slave.pcm { type dmix ipc_key 1024 slave { pcm "hw:0,0" rate 44100 } }}
TRY 3: fail
======
options snd-hda-intel model=auto
Help!

Hi Scott Fella,
Thanks for your answer.
When the problem appears, the version of the wlc was 6.0.182. We 've made upgrade to version 7.0.116.0 to try to resolve the problem, but the problem remains.
The 2 others WLC that is working fine, have the version 6.0.182.
There isn't any FW between the WLC's and WCS.
Best Regards,
Luis Matos

JC onsole failed to connect

Hi,
I run java application with following args :
java -Dcom.sun.management.jmxremote.ssl=false -Dcom.sun.management.jmxremote.authenticate=false -Dcom.sun.management.jmxremote.port=60303 -Xdebug -Xrunjdwp:transport=dt_socket,address=50303,suspend=n,server=y
I am able to debug the application from eclipse using remote debug but when I run jconsole it failed to connect.
The apllication run on linux machine.
What can be the reason for that ?
How it can be debug ?
Thanks

There is a software incompatibility here: WCS 5.1 does NOT support WLC 4.1, as per the release notes:
http://www.cisco.com/en/US/docs/wireless/wcs/release/notes/WCS_RN5_1.html
I would suggest you the latest 4.2 WCS code if you are not planning to change the code on the WLC.
If you think about upgrading your WLC, then avoid WCS 5.1, and go to the latest 5.2 or 6.0.

Apex fails to connect after rebooting XE

Hi:
My environment is Apex 4.0.0, Oracle XE 10.2.0, Apex default Gateway, Windows 2008 32 bit.
After I reboot the database, Apex fails to connect.
If I check the Apex port number, it lists 8080, as expected. (SELECT DBMS_XDB.GETHTTPPORT FROM DUAL;)
Look at the Oracle Listener status below after the reboot, notice the host value in line
(DESCRIPTION=(ADDRESS=(PROTOCOL=tcp)(HOST=127.0.0.1)(PORT=8080))(Presentation=HTTP)(Session=RAW))
When I reset the Apex port number to 8080, I can then connect OK (EXEC DBMS_XDB.SETHTTPPORT(8080); )
Look at value of HOST in the Oracle Listener status below after the reset, the HOST lists the Server Name.
(DESCRIPTION=(ADDRESS=(PROTOCOL=tcp)(HOST=galapp13.bsci.bossci.com)(PORT=8080))(Presentation=HTTP)(Session=RAW))
This is a major problem, because if the Server is rebooted, nobody can connect to Apex.
I assume this is an Oracle Listener problem.
I have made no changes to the LISTENER.ora file, see values below.
Any suggestions on how to overcome this problem will be helpful.
Status of Oracle Listener after a reboot.
LSNRCTL> status
Connecting to (DESCRIPTION=(ADDRESS=(PROTOCOL=IPC)(KEY=EXTPROC_FOR_XE)))
STATUS of the LISTENER
Alias LISTENER
Version TNSLSNR for 32-bit Windows: Version 10.2.0.1.0 - Production
Start Date 02-JUN-2011 09:03:47
Uptime 42 days 22 hr. 31 min. 5 sec
Trace Level off
Security ON: Local OS Authentication
SNMP OFF
Default Service XE
Listener Parameter File D:\oraclexe\app\oracle\product\10.2.0\server\network\admin\listener.ora
Listener Log File D:\oraclexe\app\oracle\product\10.2.0\server\network\log\listener.log
Listening Endpoints Summary...
(DESCRIPTION=(ADDRESS=(PROTOCOL=ipc)(PIPENAME=\\.\pipe\EXTPROC_FOR_XEipc)))
(DESCRIPTION=(ADDRESS=(PROTOCOL=tcp)(HOST=galapp13.bsci.bossci.com)(PORT=1521)))
(DESCRIPTION=(ADDRESS=(PROTOCOL=tcp)(HOST=127.0.0.1)(PORT=8080))(Presentation=HTTP)(Session=RAW))
Status of Listener after resetting the Port number to 8080, notice the HOST = a ServerName in line:
(DESCRIPTION=(ADDRESS=(PROTOCOL=tcp)(HOST=galapp13.bsci.bossci.com)(PORT=8080))(Presentation=HTTP)(Session=RAW))
STATUS of the LISTENER
Alias LISTENER
Version TNSLSNR for 32-bit Windows: Version 10.2.0.1.0 - Production
Start Date 02-JUN-2011 09:03:47
Uptime 42 days 22 hr. 34 min. 40 sec
Trace Level off
Security ON: Local OS Authentication
SNMP OFF
Default Service XE
Listener Parameter File D:\oraclexe\app\oracle\product\10.2.0\server\network\admin\listener.ora
Listener Log File D:\oraclexe\app\oracle\product\10.2.0\server\network\log\listener.log
Listening Endpoints Summary...
(DESCRIPTION=(ADDRESS=(PROTOCOL=ipc)(PIPENAME=\\.\pipe\EXTPROC_FOR_XEipc)))
(DESCRIPTION=(ADDRESS=(PROTOCOL=tcp)(HOST=galapp13.bsci.bossci.com)(PORT=1521)))
(DESCRIPTION=(ADDRESS=(PROTOCOL=tcp)(HOST=galapp13.bsci.bossci.com)(PORT=8080))(Presentation=HTTP)(Session=RAW))
The parameters in LISTENER.ora
SID_LIST_LISTENER =
(SID_LIST =
(SID_DESC =
(SID_NAME = PLSExtProc)
(ORACLE_HOME = D:\oraclexe\app\oracle\product\10.2.0\server)
(PROGRAM = extproc)
(SID_DESC =
(SID_NAME = CLRExtProc)
(ORACLE_HOME = D:\oraclexe\app\oracle\product\10.2.0\server)
(PROGRAM = extproc)
LISTENER =
(DESCRIPTION_LIST =
(DESCRIPTION =
(ADDRESS = (PROTOCOL = IPC)(KEY = EXTPROC_FOR_XE))
(ADDRESS = (PROTOCOL = TCP)(HOST = galapp13.bsci.bossci.com)(PORT = 1521))
DEFAULT_SERVICE_LISTENER = (XE)

Hi
Where did you find the latest WLan driver?
Here on this Toshiba driver page you can find the latest Wlan driver:
http://aps2.toshiba-tro.de/wlan/
I recommend uninstalling firstly the old driver and then to install the newer version.
Furthermore its necessary to update the BIOS. I read in the forum that similar issues could be solved by BIOS update.
Greets

Error... Installing DSEE 11.1.1.7.0 - Failed to connect to "localhost:389"

Hi all, I'm installing DSEE 11.1.1.7.0 by the documentation given at [Oracle Documentation| http://docs.oracle.com/cd/E29127_01/doc.111170/e28973/installing--dsee.html]
Then I got the error when I executed following command.
C:\ofm_odsee_win_11.1.1.7.0_disk1_1of1\ODSEE_ZIP_Distribution\sun-dsee7\dsee7\bin> dsconf set-plugin-prop dssnmp argument:on argument:3995
Failed to connect to "localhost:389".
Make sure server is up and running.
The "set-plugin-prop" operation failed on "localhost:389".
However when i run the dsccagent info command the output is as follows -
C:\ofm_odsee_win_11.1.1.7.0_disk1_1of1\ODSEE_ZIP_Distribution\sun-dsee7\dsee7\bin>dsccagent info
Instance Path : C:\ofm_odsee_win_11.1.1.7.0_disk1_1of1\ODSEE_ZIP_Distribution\sun-dsee7\dsee7\var\dcc\agent
JMX port : 3997
SNMP port : 3996
DS port : 3995
State : Running
PID : 1724
DSCC hostname : WIN-3MIAU5A4G2O
DSCC non-secure port : 3998
DSCC secure port : 3999
SNMP v3 : Disabled
Instance version : A-A00
Edited by: Ranjeet Deshmukh on Mar 19, 2013 2:16 PM

Hi.
Intend of "dsconf set-plugin-prop dssnmp argument:on argument:3995" command is to configure a Directory Server so that it can be monitored through SNMP.
The error you got occurs as dsconf command is not able to connect to the Directory Server. By default dsconf tries to connect to port 389. If you Directory Server listens on another port, use the --port option of dsconf.
Regards,
Carole.

If a WLC fails?

Hi,
I've been asked to find out what happens if a WLC fails?
Do clients stay connected but can't connect new clients? Does everyone get kicked off?
Does the same happen with the Virtual WLC as does with a hardware box? Should I really have two WLC's ?
Thanks,

I've been asked to find out what happens if a WLC fails? Do clients stay connected but can't connect new clients?
Depends. If you don't have FlexConnect AND you don't have any redundant WLC, then clients get booted off.
Let say you don't have a redundant WLC but you have FlexConnect. If the WLC fails then the OLD client will stay connected. Unless you have a local authentication server at each site, then NO NEW clients will be able to authenticate. Another thing, when the WLC fails, the AP must NOT be reloaded. If it does, then no clients, old and new, will be able to join the wireless network
Let's say you don't have FlexConnect. When the primary WLC fails, the AP will join the secondary WLC. During the "move" from Primary to Seconday, the clients will loose connection.

Failed to connect Error - Need Help, Please

I installed , created the simple "Hello" program and it ran fine on the simulator.
Then, I click the run OTA and now I'm in deep yogurt!
I get the message:
*** Error ***
Failed to connect to device 0!
Reason:
Emulator 0 terminated while waiting for it to register!
BUILD SUCCESSFUL (total time: 4 seconds)
I just want to restore things to what they were before I selected Run OTA. I've been reading for the past 3 hours and haven't found out to restore. I even deleted and re-installed but, still get the same meassge (probably some saved java pref file...). Anyway, HOW TO RESTORE to a virgin setup????
Thanks

... I read somewhere I need to reboot - I did and it took care of it.

Remote app on ipod fails to connect to itunes 10

After upgrading to iTunes 10, my remote app on the ipod touch 4G fails to connect. I've reauthorized, which times out most times, but eventually when it works, it only continues to connect to iTunes until I close and restart the program. I've disabled all firewalls and still have the issue. iTunes 10/iPod Touch 4G/iOS 4.1/ancient remote.app do not play well together.
Anyone else unable to get the remote app working reliably with this combination?

Hello all,
I would like to get more details from people who are still having trouble getting Remote 2.0.1 to connect. If you are unable to connect, please email me <[email protected]> with the following information:
- A detailed description of the specific issue you are seeing.
- What OS is on the host computer? (the one with iTunes on it)
- What OS is on the affected iOS device(s)?
- A description of your network topology. Please be as detailed as you can, including hardware and firmware versions, if possible. Also please explain how everything is connected.
- Is the base station running default settings, or do you have any non-standard settings enabled? If so, please elaborate.
- Do you have the built-in firewall enabled on the host computer?
- Do you have any other firewall or Internet protection (anti-virus, etc) installed on the host computer?
- Were you able to connect with versions of Remote prior to 2.0?
- If you have multiple computers, can you get Remote to connect to any of them?
- Does Home Sharing work between computers on your network?
- Do you see any messages in Console (in Applications/Utilities) on the host computer that seem to coincide with the connection failures?
Thanks,
Roy
<[email protected]>

My iphone 5 won't make a call when i fail to connect to the internet via 3g

My iphone 5 won't call when i fail to connect to the internet via 3g.
At work i dont have wifi i have 3g, if i launch say the sky go app,or the iplayer, sometimes they work and everything is fine...sometimes they wont load as 3g for whatever reason cant get a connection at that particular time........ if i then try and make a call the call will fail. I've experimented 25 + times and this is definately the cause.
(note: when the 3g connection does work, the phone has absolutely no problem calling people)
Anyone had this problem?
Even better has anyone got a solution?
Thanks,
Nick.

Are you sure that the carrier's signal is strong where you are having this problem? Certain building structures and locations have poor cellular signal strength and this often results in the "No Service" indication. Are other users able to get service in the same locations where you have problems?

On Windows 2012 Terminal Server Outlook fails to connect to Exchange 2013

I have a new install of Windows 2012.  I have two physical servers. One is a W2012 std Domain Controller ("DC"). The Second is configured as W2012 HyperV  ("HV"). Under HV I have
two VMs. One VM is W2012/Exchange 2013 ("ExchVM) and the other is W2012/Terminal Server ("VMTS"). All systems are behind a firewall appliance. Exchange is working via Outlook and OWA internally and externally. The self
created SSL must be installed manually on external machines since it comes up as an untrusted certificate. Once installed remote outlook works and OWA works. I have configured the terminal server and I am able
to login remotely as various users under my "TS group". The problem is when ever I attempt to open Outlook for the 1st time, it fails to connect to the exchange server.   (Open Outlook 2013, click next
on the splash screen, "Yes" Add an Email Account splash screen, click next, Auto Account screen populates NAME and Email Address correctly, click next, Searching for mail server settings..., check on establishing network connection, check on searching
for alias@ domain, then fails the logging on to the mail server) The error reads: "Outlook cannot log on. Verify you are connected to the network and are using the proper server and mailbox name. The
connection to Microsoft Exchange is unavailable. Outlook must be online or connected to complete this action."   I am connected in RDS from offsite, and from the RD session I can access shared folders on ExchVM and DC. I have
tried have verified the server Exchange server name is correct via "Get=ClientAccessServer" command. I have also tried to use the guid via "Get-Mailbox
ALIAS | fl name, exchangeguid. Keep in mind all desktop users on the network are connecting to Outlook without issue.
I would appreciate any thoughts on solving this issue.

Hi,
According to your workaround, it seems that the Outlook Anywhere configuration in Outlook client is not correct when using the Autodiscover service.
Once you connected to Exchange server by manually settings, please run Test E-mail AutoConfiguration tool in external Outlook client to check the autodiscover service:
open Outlook - press CTRL key - right click on the Outlook icon from right bottom corner taskbar - Test Email AutoConfiguration. Put your email address - uncheck use guessmart and secure guessmart authentication - click Test to check your Autodiscover service.
Please check the Log tab and confirm whether the Autodiscover service is connected successfully. Also confirm if the connection issue happens to all external users when they open Outlook for the 1st time. In Exchange server, please make sure
autodiscover.domain.com has been included in your Exchange certificate which is assigned with IIS service.
Regards,
Winnie Liang
TechNet Community Support

My new i phone 5 wont sync with my laptop, keeps saying failed to connect to sync services. any help?

I just purchased a new i phone 5. when i go to connect with my laptop it says 'failed to connect to sync services, try again later' it shows my phone, and i can see my app screens, however it wont let me sync, back up or make changes. this is my first apple product, any help would be greatly appreciated.

Hello there, load dogg.
The following Knowledge Base article provides some in-depth steps to help troubleshoot the issue you are descibing:
iTunes for Windows: "Unable to load data class" or "Unable to load provider data" sync services alert
http://support.apple.com/kb/ts2690
Thanks for reaching out to Apple Support Communities for answers to your question.
Cheers,
Pedro D.

OBIEE 11g agents are failed to connect to Essbase

OBIEE 11g agents are failed to connect to Essbase. We are using :USER & :PASSWORD (SSO) in connection pool setting to connect to Essbase.
User account exists in both OBIEE and Essbase. OBIEE dashboards which are based on Essbase are working fine. Essbase variables in RPD are upto date.
Only agents are failing and error says invalid credentials, but dashboard pages are running without any issue.
OBIEE: 11.1.1.5 (BP4)
Essbase: 11.1.2.1
Error Codes: OPR4ONWY:U9IM8TAC:OI2DL65P
State: HY000. Code: 10058. [NQODBC] [SQL_STATE: HY000] [nQSError: 10058] A general error has occurred. [nQSError: 43113] Message returned from OBIS. [nQSError: 43119] Query Failed: [nQSError: 96002] Essbase Error: Login fails due to invalid login credentials (HY000)
Essbase and OBIEE services are up and running.
Any help will be appreciated.

We finally implemented CSS Token option and ended up with this error. We are unable to connect to essbase with CSS Token option.
We followed the Oracle document to implement this.
[nQSError: 43119] Query Failed: EPMCSS-00301: Failed to authenticate user. Invalid credentials. Enter valid credentials. (HY000)
We did update this property:
JAVA_PROPERTIES="-Dplatform.home=${WL_HOME} -Dwls.home=${WLS_HOME} -Dweblogic.home=${WLS_HOME} -Didstore.identityAttribute=objectguid"
Any help will be appreciated!

Fingerprint reader not working in IE and saying failed to connect to sensor

Hi all,
I bought a Qosmio x500 10t a couple of months back. For the first couple of weeks i had no probs using the fingerprint reader to log in to windows and to log in to websites in Internet exploer.
All of a sudden it would not work on any website stored. The green banner showed accross the top of site and asked to swipe finger but nothing happened when I swiped. I rebooted and it worked again but not for long before failing. This time a reboot didnt work so i deleted my finger prints and websites and started from scratch. That worked for a couple of attempts before probs started again. And on trying to get into Fingerprint utility it says failure to connect to sensor. So, I did a system restore. It worked for a couple of times again and then same probs. So I found the updated utility software, uninstalled the old and put on the new. Same again, worked for a couple of times then failed.
I could not find anything stuck in the registry but to be on the safe side i did a full system clean back to factory setup using backup discs. Hey presto i thought it had worked. Everything going ok for first 24hrs and then same problems start to occur. Only this time it is also prompting me to enroll fingerprints even though i already have. And when i try to get into the utilioty it says failed to read sensor again.
The fingerprint log on to windows always works as long as i dont close the fingerprint utility down before shutting down. If i do exit the utilty i cant reopen it as it just says failed to connect to sensor. And then i have to unistall and reinstall the utility software. Aty the moment it occasionally works on websites stored but most of the time it doesnt do anything.
Please help. Do I need to send laptop back to Toshiba??

Hi,
*I got a solution* for the problem that the fingerprint sensor "suddenly" does not work any more.
When starting the Toshiba Fingerprint Utility, it says "failed to connect to fingerprint sensor".
Is it possible that just before it stopped working there was a new firewall installed, or firewall settings had been changed?
*In my case, the problem was solved by changing my firewall settings* (Windows 7 Firewall Control) to ALLOW all traffic for
the Authentec Fingerprint Sensor Service (AFSS). It is the file "AtService.exe" in C:\Program files
The reason is simple:
The Toshiba Fingerprint utility communicates with the fingerprint sensor service via TCP/IP.
Therefore, any firewall that blocks traffic on the local computer will block the communication.
*After changing my firewall settings, fingerprint sensor works* on my R700 flawlessly now.

Error while connecting to an OData Feed from Excel 2013 PowerPivot . Error: Failed to connect to the server. Reason: The payload kind 'BinaryValue' of the given data feed is not supported

I am trying to connect to a Odata Data feed from Excel 2013 Power Pivot
The datasource is in sharepoint site eg: https://sitename/Shared%20Documents/datafeed.atomsvc
getting below error
Error message:
Failed to connect to the server. Reason: The payload kind 'BinaryValue' of the given data feed is not supported.
============================
Call Stack:
============================
   at Microsoft.Data.DataFeedClient.DataFeedODataReader.ValidatePayloadKind(ODataPayloadKind payloadKind, ODataMessageReader odataMessageReader)
   at Microsoft.Data.DataFeedClient.DataFeedODataReader.InterceptODataException(Action action)
   at Microsoft.Data.DataFeedClient.DataFeedODataReader..ctor(IODataResponseMessage responseMessage, Int64 maxReceivedMessageSize)
   at Microsoft.Data.DataFeedClient.DataFeedODataReader.CreateReader(IWebResponse webResponse, Int64 maxReceivedMessageSize, Boolean applySlashUpdatingBaseUriResolver)
   at Microsoft.Data.DataFeedClient.ODataHelper.GetCollectionsFromServiceDocumentUrl(Uri serviceDocumentUrl, DataFeedConnection connection)
   at Microsoft.Data.DataFeedClient.DataFeedConnection.Open()
   at Microsoft.AnalysisServices.BackEnd.RelationalDataSourceConnection.InitializeConnectionObject(String connectionIdentifier)
   at Microsoft.AnalysisServices.BackEnd.RelationalDataSourceConnection.InitializeConnectionObject(String connectionIdentifier)
   at Microsoft.AnalysisServices.BackEnd.RelationalDataSourceConnection.Open(String& connectionIdentifier)
   at Microsoft.AnalysisServices.BackEnd.RelationalDataSourceConnection.Open()
   at Microsoft.AnalysisServices.Common.DataSourceBasic.ClickTestConnection(Object progressControl)
Appreciate suggestions/answers
NOTE: The error is showing only while using Excel 2013 powerpivot
its working good with Excel 2010 powerpivot

Anita,
Please look into using Power Query to use OData as a source in Power Pivot.
Thanks!
Ed Price, Power BI & SQL Server Customer Program Manager (Blog,
Small Basic,
Wiki Ninjas,
Wiki)
Answer an interesting question?
Create a wiki article about it!

WLC failed to connect to WCS by snmp

Similar Messages

Maybe you are looking for