WLC HA 7.6.120

Hello all, I configured 2 WLC 5508 with version 7.6.120 in HA, one of them had the management trought management-port (the primary) and the other had the management trought the service-port.
When I setted SSO enable I lost the management to the secondary and when I finished to configure the HA I tested and I can access to the GUI only when the primary is active but if the primary goes down I can't access to the GUI but everything is working fine.
Thanks in advance

Restrictions for High Availability
An HA-SKU controller with an evaluation license cannot become a standby controller. However, an HA-SKU controller with zero license can become a standby controller.
It is not possible to access the standby-hot controller through the controller GUI, Cisco Prime Infrastructure, or Telnet. You can access the standby-hot controller only on its console.
After you enable SSO, you must access both the standby and active controller using:
The console connection
SSH facility on the service port
SSH facility on the redundant management interface
http://www.cisco.com/c/en/us/td/docs/wireless/controller/7-4/configuration/guides/consolidated/b_cg74_CONSOLIDATED/b_cg74_CONSOLIDATED_chapter_01110100.html#concept_6C8DB7891E764C869E5FC11349120C20

Similar Messages

  • Cannot add WLC 5508 v7.6.120.0 into Prime Infrastructure 2.1

    Hi everyone
    Hope you can help us with this issue.
    We already configure the WLC using this guide: http://mrncciew.com/2013/02/14/configuring-snmp-on-wlc/
    snmp v2: enable
    snmp v1: enable
    default port values
    community: incaenic with ip and mask 0.0.0.0 to allow access from any network or ip
    traps receiver:                   community: incaenic                 ip: 10.100.100.15
    when we try to discover the WLC with the PI it gave the error "SNMP Connectivity Fail"
    WLC is on subnet 10.100.102.0/24 and PI in 10.100.100.0/24; there is a Catalyst 3850 between then with no access list on then.
    Did someone can guide us with this?
    Best Regards.
    Alvaro Rugama

    Hi,
    Which version of SNMP are you using?
    If you are using v1/v2 you should be using community string rather than local database credentials?
    Regarding the service port what is the ip address assigned on the service port. From the configuration guide "Prime Infrastructure uses the preferred management IP address from the loop back interface. If the device does not have a loopback interface, Prime Infrastructure uses similar logic to the OSPF algorithm to select the router’s preferred management IP address."
    Hope that helps.
    Regards
    Najaf

  • 7925 Phones voice quality issues with wlc 5508 version 7.6

    Hi all,
    I have a mix environment with 1 WLC 5508  and more or less 6 sites with several Access Points ( all AIR-LAP1242AG and all in FlexConnect mode  Hreap ) and several wireless phones (all  CP7925G) . My Ap's have antennas 2.4GHz in all sites except 1 site ( the one i'm talking for now) with 2.4GHz and 5GHz , because of the problems we suggest to have all phone in A BAND (5Ghz) . In this site we force the phones just to A (802.11a only) , power safe NONE , Continuous scan mode , i fallow all in http://www.cisco.com/en/US/docs/voice_ip_comm/cuipph/7925g/7_0/english/deployment/guide/7925dply.pdf , one thing i didn’t do it was apply QoS because I can’t apply several ios commands in that 2960 with lan lite ios.
    So I have 3 SSID for data and 2 for VOICE  ( one is common to all environment and supports 2.4 and 5Ghz , and other just to test one site , with only 5Ghz  with “[WPA2][Auth(802.1X + CCKM)][Auth(FT 802.1X)]”, because I read that problem can be phone rooming , and in FlexConnect only have fast-roaming in a CCKM or a PKM  key-management solution , but even like this the problem still exist) .
    I have another sites with phones in 2.4GHz running well and others with problems.
    i read here in forums lots and lots of people with similar problems , i tried several solutions ( WLC  upgrades versions  and phones firmware's , ….  ) tried all my best of solving the problems mas now I’m running without any ideas , i did also some site surveys and detect some interferers that why I change phones to 5Ghz , and I run also WLC Config analyser to help me , but all without good success. Some changes solve temporarily problems , but after some time , people reclaim about problems.
    I can open a TAC case but first I want be sure if did all already.
    Can someone try to help me?
    ip phone 7925G firmware : CP7925G-1.4.5SR1.3      
    CUCM 8.6.2
    WLC    5508 : 7.6.120.0
    AP : AIR-LAP1242AG-E-K9    7.6.120.0       (flexconnect)
    Best Regards

    Hi Serge,
    Thanks for the suggestions. I have taken care of all the settings. Problem is , the user is seated in his office cabin and using the 7925 and there is around 50db signal strength in his room from an AP which is just outside the cabin. And this doesnt occur often, when we go to check and make calls, everything is fine whereas the user says it happens sometimes in the morning, evening etc... randomly... where the fone goes blank while in a call.... since the problem never happens when we go to troubleshoot the issue, we really dont know what is going on. This is happening when calling PSTN.
    AP's are not restarting and there is no logs indicating that. Wireless infrastructure looks very much OK cos there are other users who are not experiencing this problem and there is ample coverage all over the floor. I am baffled why only one user has this problem even when he is seated in his office cabin.
    Tried changing phones also, but still remains.
    Question  : i tried to do a linktest from WLC to his phone, but it failed, while linktest to laptops are working fine. Does wlc linktest not working for wireless phones ?
    regards
    Joe

  • Mac OSx/5508/3702i dropping issue

    Hi all,
    I have installed dozens of WLCs but with this one customer rollout I have hit an impasse.  The customer has a 98% MacOS device environment running a 5508 HA pair and 3702i APs.  The Mac OSx users randomly lose access even when their device sits in one place within 10 feet of a below ceiling tile hung AP. Disconnects can't be recreated as no particular behavior seems to trigger the drop.  Also for some clients there is severe latency(>1000ms) just pinging the WLAN gateway. Pings from Gateway SVI to AP are fine(<5ms) Debugs imply AP is too busy to handle an authentication request even thought the AP only has 10 users and an insignificant amount of traffic flowing through it. This issue is not dedicated to just one AP either as folks all over the 30 AP environment suffer similarly.  Air Magnet shows no coverage holes.  Windows devices appear ok.
    I am more interested if this is has happened to anyone else and if anyone has had something that has fixed this issue for them instead of troubleshooting.
    TAC case has been open over 4 months with escalation and Backbone TAC involvement with no luck.
    Details:
    - Mac OSx versions are random and those running Yosemite do have the latest patch.
    - WLC versions 7.6.120, 7.6.130, 8.0.102MR, and 8.0.110 have not corrected the problem.  (although fewer errors are seen in the debugs)
    - Although APs are actually local to the controller, the customer has them in Flexconnect for HA and Bandwidth reasons.
    - problem happens with Band Steering and also with Dedicated 5Ghz SSID (2.4 unusable due to density of APs using 2.4 in surrounding buildings)
    - Clear Air 5ghz report score above 97%
    - tried Legacy Beam forming, no joy.
    - EDRRM is on
    - Fast Transition is on
    - Fast SSID switching is on
    - Problem occurs with 20 and 40 Mhz channel bonding.
    - 802.11k sticky cache has been tried to no avail.
    - FUS is at 1.8 (I hear FUS 1.9.0.0 not only fixes the subsystem bugs but may iron out problems with the Operation side too)
    - SSID running dynamic vlan assignment from NPS Server
    - 6 SSIDs total
    - No DFS channels being used
    - SSID timeout has been turned off
    - Data rates below 9Mbit are disabled
    - APs are roughly 25 feet apart.

    Thanks Leo,
              Problem happens to multiple versions of OSx, those running Yosemite do have the latest patch.  Unfortunately I don't think disabling N is going to be feasible.  Due to the High density rate there is no b/g to fallback on (2.4 Ghz is completely saturated).  So that would leave users with basically just 802.11a?  I do have a customer with similar set up running 5508 (v7.6.130) with 3702 in flexconnect.  The difference is the1.9.0.0 FUS has been applied and they run Pre-shared key authentication. Where as the problem customer runs older FUS and Dynamic Radius based vlan assignment.

  • CPI Error: COMMON-1: Some unexpected internal error has occurred

    Prime Infrastructure version 1.4 (1.4.0.45)
    4 5508 WLC running 7.6.120
    I've been getting this COMMON-1 in CPI recently when making a configuration change to an AP or a WLC.  I think it happens the most when I'm making a change to an AP.  We have 1142, 3500s, and 3600 and I don't know if I get it with a particular model AP.
    Has anyone else received this message?  I attached a screen shot.

    You may need to look at upgrading PI. Take a look at the compatibility matrix. Some things will still work fine as far as monitoring, but templates and or features may not and it is limited with the PI version. 
    http://www.cisco.com/c/en/us/td/docs/wireless/compatibility/matrix/compatibility-matrix.html#31079
    -Scott

  • 7.6.130.0 or 8.0 ?

    Hi Wireless Experts,
    We have 5508 WLCs running 7.6.120.0 since July 2014.  No major issue so far but some inconvenience due to some little bug.
    Just noticed that 7.6.120.0 is not available to download on Cisco webiste any more because some critical bugs were found.
    It made us a bit nervous, even though there is only a very small portion of our environment might be impacted by these bugs.
    May I please ask your opinion, as of today, which version is stable enough and better, 7.6.130.0 or 8.0 (8.0.115.0  /  8.0.110.0  /  8.0.100.0)?
    Thanks,
    Cedar

    I would upgrade to 7.6.130.0 (after a proper bug scrub w/ your environment and used features in mind, of course). A seasoned veteran once advised me to avoid upgrading to any .0 release from Cisco. I've mostly followed that rule and been happier for it.

  • Voice over Wireless with Cisco phones 7921 and 7925

    Hello experts,
    I made an wireless audit for a company.
    They have 2 WLCs 5508 in HA mode, with APs 2602 for indoor and 1552. Version of the WLC : 7.6.120.0
    At the end of the day we noticed that the roaming between indoor and outdoor access points is sometimes failing and results to a complete disconnection of the wireless phone (7921 or 7925) from the network. When people go from the indoor to the outdoor area, there is no problem. The problem comes when people are coming from the outdoor to the indoor.
    Also, on the WLC, the power lvl of the outdoor APs are set to 1 ... Is it good or not ?
    My question is, is there any known issue about Voice over wireless with WLC 5508-7.6.120.0 with APs 2602 and 1552 ?
    Maybe it should be better to upgrade to 7.6.130.0 ?
    Thanks in advance,
    Alexis

    Normally yes.
    Is there a way to troubleshoot what's going on with the phones ? Maybe a "show client detail MAC address* on the WLC ?
    Here are some logs when the phones are losing the network :
    *Dot1x_NW_MsgTask_4: Apr 09 12:44:21.320: #DOT1X-3-INVALID_WPA_KEY_MSG_STATE: 1x_eapkey.c:957 Received invalid EAPOL-key M2 msg in START  state - invalid secure bit; KeyLen 40, Key type 1, client 00:24:d7:83:56:dc
    *apfMsConnTask_6: Apr 09 12:28:32.668: #APF-3-VALIDATE_CCKM_REASS_REQ_ELEMENT: apf_utils.c:2506 Could not validate the CCKM Reassociation request element.Received Timestamp deviation > 1sec in CCKM Info Element from mobile. Mobile:4c:00:82:85:6e:e1,  AP:1
    *Dot1x_NW_MsgTask_1: Apr 09 12:26:53.964: #DOT1X-3-INVALID_REPLAY_CTR: 1x_eapkey.c:445 Invalid replay counter from client 74:26:ac:63:8c:a9 - got 00 00 00 00 00 00 00 03, expected 00 00 00 00 00 00 00 04
    *Dot1x_NW_MsgTask_1: Apr 09 12:26:53.929: #DOT1X-3-INVALID_REPLAY_CTR: 1x_eapkey.c:445 Invalid replay counter from client 74:26:ac:63:8c:a9 - got 00 00 00 00 00 00 00 02, expected 00 00 00 00 00 00 00 04
    *apfMsConnTask_4: Apr 09 12:24:34.959: #APF-3-VALIDATE_CCKM_REASS_REQ_ELEMENT: apf_utils.c:2506 Could not validate the CCKM Reassociation request element.Received Timestamp deviation > 1sec in CCKM Info Element from mobile. Mobile:78:da:6e:f6:5f:89,  AP:5
    *Dot1x_NW_MsgTask_0: Apr 09 12:22:30.217: #DOT1X-3-INVALID_REPLAY_CTR: 1x_eapkey.c:445 Invalid replay counter from client 4c:00:82:85:1d:68 - got 00 00 00 00 00 00 00 03, expected 00 00 00 00 00 00 00 04
    *Dot1x_NW_MsgTask_4: Apr 09 12:22:30.206: #DOT1X-3-INVALID_REPLAY_CTR: 1x_eapkey.c:445 Invalid replay counter from client 4c:00:82:85:b3:ac - got 00 00 00 00 00 00 00 03, expected 00 00 00 00 00 00 00 04
    *Dot1x_NW_MsgTask_4: Apr 09 12:22:30.186: #DOT1X-3-INVALID_REPLAY_CTR: 1x_eapkey.c:445 Invalid replay counter from client 4c:00:82:85:b3:ac - got 00 00 00 00 00 00 00 02, expected 00 00 00 00 00 00 00 04
    *Dot1x_NW_MsgTask_0: Apr 09 12:22:30.167: #DOT1X-3-INVALID_REPLAY_CTR: 1x_eapkey.c:445 Invalid replay counter from client 4c:00:82:85:1d:68 - got 00 00 00 00 00 00 00 02, expected 00 00 00 00 00 00 00 04
    *Dot1x_NW_MsgTask_6: Apr 09 12:22:29.672: #DOT1X-3-INVALID_REPLAY_CTR: 1x_eapkey.c:445 Invalid replay counter from client 78:da:6e:f6:14:2e - got 00 00 00 00 00 00 00 03, expected 00 00 00 00 00 00 00 04
    *Dot1x_NW_MsgTask_6: Apr 09 12:22:29.638: #DOT1X-3-INVALID_REPLAY_CTR: 1x_eapkey.c:445 Invalid replay counter from client 78:da:6e:f6:14:2e - got 00 00 00 00 00 00 00 02, expected 00 00 00 00 00 00 00 04
    *apfMsConnTask_3: Apr 09 12:19:22.098: #APF-3-VALIDATE_CCKM_REASS_REQ_ELEMENT: apf_utils.c:2506 Could not validate the CCKM Reassociation request element.Received Timestamp deviation > 1sec in CCKM Info Element from mobile. Mobile:4c:00:82:85:6e:e1,  AP:5
    *osapiBsnTimer: Apr 09 12:13:36.031: #LOG-3-Q_IND: spam_lrad.c:53542 The system is unable to find WLAN 2 to be deleted

  • WLC update from 7.6.120.0 to 8.0.110.0 - speed and ms drops alot

    Hi,
    Just wanted to share incase someone ends up with the same problem as we did.
    I had to update our Wism2's and 5508's to 7.6.120.0 for 3702 support. One of the Wism2's started to hand/restart a few times per week after the update. Other than that the wireless was working good. So I made a TAC case via our Cisco partner. TAC couldnt find the error but some bugs that suited what they could read from the logs and told me to update to 8.
    So I did, and *smack* the wireless dropped to speeds around 5-10Mbits with 80+ ms. Yielding that exchange, fileservers and alot if not all programs did not function/lost connection.
    To make a longer story short.
    After the upgrade the upgrade. The upgrade itself had enabled interim update under the AAA accounting with a value of 0. I tried on our lab controller to turn on interim with the same value but the system wouldnt let me since its not an accepted value. So I turned the function off on one of the live controllers (that just had a few AP's heh) and immedietally the Wirelss were back delivering good speeds and answering times again.
    This bug might be connected to the problem https://supportforums.cisco.com/discussion/11894006/ise-12-wlc-5508-nas-sends-radius-accounting-update-messages-too-frequently
    Hope this post helps if you end up in the same position.
    Cheers,
    //Anders

    Thanks for posting this. We just upgraded to 8.0 as well and I noticed this being an issue on the AP I was connecting to. Quick Google search and that brought me to this post!
    Speeds are back to normal now!!

  • WLC 7.6.120.0 Radius problems with FreeRadius server

    Hi there
    we have 3 WLC 5508 with version 7.6.120.0 and 2 FreeRadius servers. In the WLC log we see a lot of "radius auth-server unavailable" messages and some users can not authenticate against our dot1x (PEAP).
    The problems occur most of the time, when there are a lot of WLAN clients trying to connect to the SSID at the same time.
    Does anybody have the same problems or are there any known bug for this phenomena?
    Thanks in advance and best regards
    Anna

    Hi Anna
    your problems seems to be this bug here: https://tools.cisco.com/bugsearch/bug/CSCuo96366
    Symptom:
    Clients are not able to Authenticate at Peak loads when using FreeRadius.
    Conditions:
    Using Freed radius (most susceptible), we observe at high auth rate and if Radius server is not responding to all Radius packets in seq order or if the server is slow, WLC when wraps around 0-255 Radius ID's, it does not do a check when posting new packet.
    So essentially you have 2 packets with same ID being presented to AAA server.
    Workaround:
    Recover's when load is reduced.
    Further Problem Description:
    So far, issue has not been brought to notice while using ISE/ACS/NPS.
    There are two possible solutions I see:
    1. Downgrade to an earlier WLC version <7.6 (e.g. 7.4.121.0)
    2. Try to have another radius server in between (radius proxy, e.g. Cisco ACS or Microsoft NPS)
    Best regards
    Dominic

  • 5508 WLC going to the 11ac level, any issues running ver 7.6.120?

    We do have 3850's to use. Do they have to be mobility members to the wireless system? or will the LAN base work for the connections?

    The 3850 must have IP Base or IP Services to terminate Access Points in a Converged Access wireless network.  If you are running a non-converged access network then you can use your 3850 to connect access points to the network like you would any other switch.
    You must also have RTU licenses for each AP you want to connect to your 3850/3650 switches.
    7.6.120 is non-converged access code so I am assuming you want to do the latter.
    John

  • Issue with 2504 WLC and 2602 AP. need help please.

    Somehow the AP does not associates with the 2504 controller.
    What could possibily be the issue.
    Thanks in advance.
    Anyway,  Here is the log from the AP.
    AP log
    ===========================================================
    *Mar  1 00:30:35.551: %CAPWAP-5-DHCP_OPTION_43: Controller address 192.168.120.4 obtained through DHCP
    *Mar  1 00:30:35.551: %CAPWAP-3-ERRORLOG: Did not get log server settings from DHCP.
    *Mar  1 00:30:44.551: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-CAPWAP-CONTROLLER
    *Mar  1 00:30:44.551: %CAPWAP-3-ERRORLOG: Discovery response from MWAR 'SNGNY-WLC1'running version 7.0.220.0 is rejected.
    *Mar  1 00:30:44.551: %CAPWAP-3-ERRORLOG: Failed to decode discovery response.
    *Mar  1 00:30:44.551: %CAPWAP-3-ERRORLOG: CAPWAP SM handler: Failed to process message type 2 state 2.
    *Mar  1 00:30:44.551: %CAPWAP-3-ERRORLOG: Failed to handle capwap control message from controller
    *Mar  1 00:30:44.551: %CAPWAP-3-ERRORLOG: Failed to process unencrypted capwap packet from 192.168.120.4
    ===========================================================
    show version output from the Access Point
    =========================================================
    AP0006.f6ec.be2a#show ver
    Cisco IOS Software, C2600 Software (AP3G2-RCVK9W8-M), Version 15.2(2)JB, RELEASE SOFTWARE (fc1)
    Technical Support: http://www.cisco.com/techsupport
    Copyright (c) 1986-2012 by Cisco Systems, Inc.
    Compiled Tue 11-Dec-12 00:07 by prod_rel_team
    ROM: Bootstrap program is C2600 boot loader
    BOOTLDR: C2600 Boot Loader (AP3G2-BOOT-M) LoaderVersion 12.4(25e)JA1, RELEASE SOFTWARE (fc1)
    AP0006.f6ec.be2a uptime is 33 minutes
    System returned to ROM by power-on
    System image file is "flash:/ap3g2-rcvk9w8-mx/ap3g2-rcvk9w8-xx"
    Last reload reason:
    This product contains cryptographic features and is subject to United
    States and local country laws governing import, export, transfer and
    use. Delivery of Cisco cryptographic products does not imply
    third-party authority to import, export, distribute or use encryption.
    Importers, exporters, distributors and users are responsible for
    compliance with U.S. and local country laws. By using this product you
    --More--
    *Mar  1 00:33:46.071: %CAPWAP-3-ERRORLOG: Invalid event 38 & state 2 combination.
    *Mar  1 00:33:46.171: %DHCP-6-ADDRESS_ASSIGN: Interface BVI1 assigned DHCP address 192.168.120.98, mask 255.255.255.0, hostname AP0006.f6ec.be2a
    agree to comply with applicable laws and regulations. If you are unable
    to comply with U.S. and local laws, return this product immediately.
    A summary of U.S. laws governing Cisco cryptographic products may be found at:
    http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
    If you require further assistance please contact us by sending email to
    [email protected].
    cisco AIR-CAP2602I-A-K9    (PowerPC) processor (revision A0) with 180214K/81920K bytes of memory.
    Processor board ID FGL1704ZC0Q
    PowerPC CPU at 800Mhz, revision number 0x2151
    Last reset from power-on
    LWAPP image version 7.4.1.37
    1 Gigabit Ethernet interface
    32K bytes of flash-simulated non-volatile configuration memory.
    Base ethernet MAC Address: 00:06:F6:EC:BE:2A
    Part Number                          : 73-14588-02
    PCA Assembly Number                  : 800-37899-01
    PCA Revision Number                  : A0
    PCB Serial Number                    : FOC165188Y4
    Top Assembly Part Number             : 800-38356-01
    Top Assembly Serial Number           : FGL1704ZC0Q
    Top Revision Number                  : A0
    Product/Model Number                 : AIR-CAP2602I-A-K9  
    Configuration register is 0xF
    ========================================================

    Blake's right.  Your WLC is running 7.0.X code which does not support the AP2600.  Check the Release Notes and look under Software Release Support for Access Points to determine what suitable firmware your WLC can support your AP.

  • LAP 1240 won't join WLC across subnets

    I am having a problem getting LAPs that are in other subnets to join our WLC. If I take the LAP and place it on the same VLAN/subnet as the WLC, it joins as expected. If I move it to another subnet, I get the following:
    *Mar 1 00:00:13.065: %SYS-5-RESTART: System restarted --
    Cisco IOS Software, C1200 Software (C1200-K9W8-M), Version 12.4(13d)JA, RELEASE SOFTWARE (fc2)
    Technical Support: http://www.cisco.com/techsupport
    Copyright (c) 1986-2008 by Cisco Systems, Inc.
    Compiled Fri 08-Feb-08 17:24 by prod_rel_team
    *Mar 1 00:00:13.119: %SSH-5-ENABLED: SSH 2.0 has been enabled
    *Mar 1 00:00:13.519: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset
    *Mar 1 00:00:14.519: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to down
    *Mar 1 00:00:14.536: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
    *Mar 1 00:00:14.545: %DOT11-6-FREQ_SCAN: Interface Dot11Radio0, Scanning frequencies for 24 seconds
    *Mar 1 00:00:15.536: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
    *Mar 1 00:00:28.133: %LWAPP-5-CHANGED: LWAPP changed state to DISCOVERY
    *Mar 1 00:00:28.171: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
    *Mar 1 00:00:28.177: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
    *Mar 1 00:00:28.192: SSC Load Current Size crypto_mykey 120, offset 9389, Saved Size soap_cert_crypto_mykey 124
    *Mar 1 00:00:28.390: %LINK-3-UPDOWN: Interface Dot11Radio1, changed state to up
    *Mar 1 00:00:28.892: Logging LWAPP message to 255.255.255.255.
    %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
    %SYS-6-LOGGINGHOST_STARTSTOP: Logging to host 255.255.255.255 started - CLI initiated
    %LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset
    %LINK-3-UPDOWN: Interface Dot11Radio1, changed state to up
    %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
    %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
    %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
    %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to up
    %DHCP-6-ADDRESS_ASSIGN: Interface FastEthernet0 assigned DHCP address 192.168.115.75, mask 255.255.255.192, hostname AP0013.c3a7.bf97
    Translating "CISCO-LWAPP-CONTROLLER.mydomain.here"...domain server (X.X.X.X) [OK]
    %LWAPP-3-CLIENTEVENTLOG: Did not get vendor specific options from DHCP.
    %LWAPP-3-CLIENTEVENTLOG: Did not get log server settings from DHCP.
    %LWAPP-3-CLIENTEVENTLOG: Performing DNS resolution for CISCO-LWAPP-CONTROLLER.mydomain.here
    %LWAPP-3-CLIENTEVENTLOG: Controller address Y.Y.Y.Y obtained through DNS
    %LWAPP-5-CHANGED: LWAPP changed state to JOIN
    %LINK-5-CHANGED: Interface Dot11Radio0, changed state to administratively down
    %LINK-5-CHANGED: Interface Dot11Radio1, changed state to administratively down
    %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
    %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to down
    %LWAPP-3-CLIENTERRORLOG: Join Timer: did not recieve join response (controller - 2169-WLC4402-1)
    %LWAPP-3-CLIENTERRORLOG: Set Transport Address: no more AP manager IP addresses remain
    %SYS-5-RELOAD: Reload requested by LWAPP CLIENT. Reload Reason: DID NOT GET JOIN RESPONSE.
    %LWAPP-5-CHANGED: LWAPP changed state to DOWN
    I have checked the WLC for any messages that look like crypto or other problems, but I don't see anything that stands out. Any suggestions or pointers would be greatfully accepted.

    %LWAPP-3-CLIENTERRORLOG: Set Transport Address: no more AP manager IP addresses remain
    Can you provide more information such as:
    1. How many APs can the WLC4402 support and how many are currently joined?
    2. What is your WLC's firmware?
    3. Is there a possibility of a duplicate IP address in your network?
    Troubleshoot a Lightweight Access Point Not Joining a Wireless LAN Controller
    http://www.cisco.com/en/US/products/ps6366/products_tech_note09186a00808f8599.shtml

  • Device issue with WLC (excluded client)

    I have a single client that is having issues staying connected to my WLC running code 7.0.220.0
    Here are the debugs, it just keeps on looping:
    *apfMsConnTask_0: Jul 18 10:41:06.352: 00:40:96:b8:78:7a Adding mobile on LWAPP AP 10:8c:cf:78:93:80(0)
    *apfMsConnTask_0: Jul 18 10:41:06.352: 00:40:96:b8:78:7a Association received from mobile on AP 10:8c:cf:78:93:80
    *apfMsConnTask_0: Jul 18 10:41:06.352: 00:40:96:b8:78:7a 0.0.0.0 START (0) Changing ACL 'none' (ACL ID 0) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:1626)
    *apfMsConnTask_0: Jul 18 10:41:06.352: 00:40:96:b8:78:7a Applying site-specific IPv6 override for station 00:40:96:b8:78:7a - vapId 11, site 'TWR-5', interface 'pharmwireless'
    *apfMsConnTask_0: Jul 18 10:41:06.352: 00:40:96:b8:78:7a Applying IPv6 Interface Policy for station 00:40:96:b8:78:7a - vlan 274, interface id 12, interface 'pharmwireless'
    *apfMsConnTask_0: Jul 18 10:41:06.352: 00:40:96:b8:78:7a Applying site-specific override for station 00:40:96:b8:78:7a - vapId 11, site 'TWR-5', interface 'pharmwireless'
    *apfMsConnTask_0: Jul 18 10:41:06.352: 00:40:96:b8:78:7a 0.0.0.0 START (0) Changing ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:1626)
    *apfMsConnTask_0: Jul 18 10:41:06.353: 00:40:96:b8:78:7a STA - rates (6): 24 36 48 72 96 108 0 0 0 0 0 0 0 0 0 0
    *apfMsConnTask_0: Jul 18 10:41:06.353: 00:40:96:b8:78:7a Processing RSN IE type 48, length 38 for mobile 00:40:96:b8:78:7a
    *apfMsConnTask_0: Jul 18 10:41:06.353: 00:40:96:b8:78:7a 0.0.0.0 START (0) Initializing policy
    *apfMsConnTask_0: Jul 18 10:41:06.353: 00:40:96:b8:78:7a 0.0.0.0 START (0) Change state to AUTHCHECK (2) last state AUTHCHECK (2)
    *apfMsConnTask_0: Jul 18 10:41:06.353: 00:40:96:b8:78:7a 0.0.0.0 AUTHCHECK (2) Change state to 8021X_REQD (3) last state 8021X_REQD (3)
    *apfMsConnTask_0: Jul 18 10:41:06.353: 00:40:96:b8:78:7a 0.0.0.0 8021X_REQD (3) DHCP Not required on AP 10:8c:cf:78:93:80 vapId 11 apVapId 8for this client
    *apfMsConnTask_0: Jul 18 10:41:06.353: 00:40:96:b8:78:7a Not Using WMM Compliance code qosCap 00
    *apfMsConnTask_0: Jul 18 10:41:06.353: 00:40:96:b8:78:7a 0.0.0.0 8021X_REQD (3) Plumbed mobile LWAPP rule on AP 10:8c:cf:78:93:80 vapId 11 apVapId 8
    *apfMsConnTask_0: Jul 18 10:41:06.353: 00:40:96:b8:78:7a apfMsAssoStateInc
    *apfMsConnTask_0: Jul 18 10:41:06.353: 00:40:96:b8:78:7a apfPemAddUser2 (apf_policy.c:223) Changing state for mobile 00:40:96:b8:78:7a on AP 10:8c:cf:78:93:80 from Idle to Associated
    *apfMsConnTask_0: Jul 18 10:41:06.353: 00:40:96:b8:78:7a Scheduling deletion of Mobile Station:  (callerId: 49) in 1800 seconds
    *apfMsConnTask_0: Jul 18 10:41:06.353: 00:40:96:b8:78:7a Sending Assoc Response to station on BSSID 10:8c:cf:78:93:80 (status 0) ApVapId 8 Slot 0
    *apfMsConnTask_0: Jul 18 10:41:06.353: 00:40:96:b8:78:7a apfProcessAssocReq (apf_80211.c:5237) Changing state for mobile 00:40:96:b8:78:7a on AP 10:8c:cf:78:93:80 from Associated to Associated
    *dot1xMsgTask: Jul 18 10:41:06.354: 00:40:96:b8:78:7a Creating a PKC PMKID Cache entry for station 00:40:96:b8:78:7a (RSN 2)
    *dot1xMsgTask: Jul 18 10:41:06.354: 00:40:96:b8:78:7a Adding BSSID 10:8c:cf:78:93:87 to PMKID cache for station 00:40:96:b8:78:7a
    *dot1xMsgTask: Jul 18 10:41:06.355: New PMKID: (16)
    *dot1xMsgTask: Jul 18 10:41:06.355:      [0000] 4a 0c ea 60 5c 8c 76 2a ee 47 50 bd ad 58 e0 d9
    *dot1xMsgTask: Jul 18 10:41:06.355: 00:40:96:b8:78:7a Initiating RSN PSK to mobile 00:40:96:b8:78:7a
    *dot1xMsgTask: Jul 18 10:41:06.355: 00:40:96:b8:78:7a dot1x - moving mobile 00:40:96:b8:78:7a into Force Auth state
    *dot1xMsgTask: Jul 18 10:41:06.355: 00:40:96:b8:78:7a Skipping EAP-Success to mobile 00:40:96:b8:78:7a
    *dot1xMsgTask: Jul 18 10:41:06.355: Including PMKID in M1  (16)
    *dot1xMsgTask: Jul 18 10:41:06.355:      [0000] 4a 0c ea 60 5c 8c 76 2a ee 47 50 bd ad 58 e0 d9
    *dot1xMsgTask: Jul 18 10:41:06.355: 00:40:96:b8:78:7a Starting key exchange to mobile 00:40:96:b8:78:7a, data packets will be dropped
    *dot1xMsgTask: Jul 18 10:41:06.355: 00:40:96:b8:78:7a Sending EAPOL-Key Message to mobile 00:40:96:b8:78:7a
                                  state INITPMK (message 1), replay counter 00.00.00.00.00.00.00.00
    *osapiBsnTimer: Jul 18 10:41:07.362: 00:40:96:b8:78:7a 802.1x 'timeoutEvt' Timer expired for station 00:40:96:b8:78:7a and for message = M2
    *dot1xMsgTask: Jul 18 10:41:07.362: 00:40:96:b8:78:7a Retransmit 1 of EAPOL-Key M1 (length 121) for mobile 00:40:96:b8:78:7a
    *apfLbsTask: Jul 18 10:41:07.762: 00:40:96:b8:78:7a Copy AP LOCP - mode:0 slotId:0, apMac 0x10:8c:cf:78:93:80
    *apfLbsTask: Jul 18 10:41:07.762: 00:40:96:b8:78:7a Copy WLAN LOCP EssIndex:11 aid:1 ssid:RUMCWireless-S
    *apfLbsTask: Jul 18 10:41:07.762: 00:40:96:b8:78:7a Copy Security LOCP ecypher:0x0 ptype:0x2, p:0x1, eaptype:0x6 w:0x1 aalg:0x0, PMState: 8021X_REQD
    *apfLbsTask: Jul 18 10:41:07.762: 00:40:96:b8:78:7a Copy 802.11 LOCP a:0x0 b:0x0 c:0x0 d:0x0 e:0x1 protocol2:0x2 statuscode 0, reasoncode 1, status 3
    *apfLbsTask: Jul 18 10:41:07.762: 00:40:96:b8:78:7a Copy CCX LOCP 5
    *apfLbsTask: Jul 18 10:41:07.762: 00:40:96:b8:78:7a Copy MobilityData LOCP status:0, anchorip:0x0
    *osapiBsnTimer: Jul 18 10:41:08.361: 00:40:96:b8:78:7a 802.1x 'timeoutEvt' Timer expired for station 00:40:96:b8:78:7a and for message = M2
    *dot1xMsgTask: Jul 18 10:41:08.361: 00:40:96:b8:78:7a Retransmit 2 of EAPOL-Key M1 (length 121) for mobile 00:40:96:b8:78:7a
    *osapiBsnTimer: Jul 18 10:41:09.361: 00:40:96:b8:78:7a 802.1x 'timeoutEvt' Timer expired for station 00:40:96:b8:78:7a and for message = M2
    *dot1xMsgTask: Jul 18 10:41:09.362: 00:40:96:b8:78:7a Retransmit failure for EAPOL-Key M1 to mobile 00:40:96:b8:78:7a, retransmit count 3, mscb deauth count 0
    *dot1xMsgTask: Jul 18 10:41:09.363: 00:40:96:b8:78:7a Sent Deauthenticate to mobile on BSSID 10:8c:cf:78:93:80 slot 0(caller 1x_ptsm.c:534)
    *dot1xMsgTask: Jul 18 10:41:09.363: 00:40:96:b8:78:7a Scheduling deletion of Mobile Station:  (callerId: 57) in 10 seconds
    *apfMsConnTask_0: Jul 18 10:41:12.953: 00:40:96:b8:78:7a Association received from mobile on AP 10:8c:cf:78:93:80
    *apfMsConnTask_0: Jul 18 10:41:12.953: 00:40:96:b8:78:7a 0.0.0.0 8021X_REQD (3) Changing ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:1626)
    *apfMsConnTask_0: Jul 18 10:41:12.953: 00:40:96:b8:78:7a Applying site-specific IPv6 override for station 00:40:96:b8:78:7a - vapId 11, site 'TWR-5', interface 'pharmwireless'
    *apfMsConnTask_0: Jul 18 10:41:12.953: 00:40:96:b8:78:7a Applying IPv6 Interface Policy for station 00:40:96:b8:78:7a - vlan 274, interface id 12, interface 'pharmwireless'
    *apfMsConnTask_0: Jul 18 10:41:12.953: 00:40:96:b8:78:7a Applying site-specific override for station 00:40:96:b8:78:7a - vapId 11, site 'TWR-5', interface 'pharmwireless'
    *apfMsConnTask_0: Jul 18 10:41:12.953: 00:40:96:b8:78:7a 0.0.0.0 8021X_REQD (3) Changing ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:1626)
    *apfMsConnTask_0: Jul 18 10:41:12.953: 00:40:96:b8:78:7a STA - rates (6): 24 36 48 72 96 108 0 0 0 0 0 0 0 0 0 0
    *apfMsConnTask_0: Jul 18 10:41:12.953: 00:40:96:b8:78:7a Processing RSN IE type 48, length 38 for mobile 00:40:96:b8:78:7a
    *apfMsConnTask_0: Jul 18 10:41:12.953: 00:40:96:b8:78:7a 0.0.0.0 8021X_REQD (3) Initializing policy
    *apfMsConnTask_0: Jul 18 10:41:12.953: 00:40:96:b8:78:7a 0.0.0.0 8021X_REQD (3) Change state to AUTHCHECK (2) last state 8021X_REQD (3)
    *apfMsConnTask_0: Jul 18 10:41:12.953: 00:40:96:b8:78:7a 0.0.0.0 AUTHCHECK (2) Change state to 8021X_REQD (3) last state 8021X_REQD (3)
    *apfMsConnTask_0: Jul 18 10:41:12.953: 00:40:96:b8:78:7a 0.0.0.0 8021X_REQD (3) DHCP Not required on AP 10:8c:cf:78:93:80 vapId 11 apVapId 8for this client
    *apfMsConnTask_0: Jul 18 10:41:12.953: 00:40:96:b8:78:7a Not Using WMM Compliance code qosCap 00
    *apfMsConnTask_0: Jul 18 10:41:12.953: 00:40:96:b8:78:7a 0.0.0.0 8021X_REQD (3) Plumbed mobile LWAPP rule on AP 10:8c:cf:78:93:80 vapId 11 apVapId 8
    *apfMsConnTask_0: Jul 18 10:41:12.953: 00:40:96:b8:78:7a apfPemAddUser2 (apf_policy.c:223) Changing state for mobile 00:40:96:b8:78:7a on AP 10:8c:cf:78:93:80 from Associated to Associated
    *apfMsConnTask_0: Jul 18 10:41:12.953: 00:40:96:b8:78:7a Scheduling deletion of Mobile Station:  (callerId: 49) in 1800 seconds
    *apfMsConnTask_0: Jul 18 10:41:12.954: 00:40:96:b8:78:7a Sending Assoc Response to station on BSSID 10:8c:cf:78:93:80 (status 0) ApVapId 8 Slot 0
    *apfMsConnTask_0: Jul 18 10:41:12.954: 00:40:96:b8:78:7a apfProcessAssocReq (apf_80211.c:5237) Changing state for mobile 00:40:96:b8:78:7a on AP 10:8c:cf:78:93:80 from Associated to Associated
    *dot1xMsgTask: Jul 18 10:41:12.955: 00:40:96:b8:78:7a Creating a PKC PMKID Cache entry for station 00:40:96:b8:78:7a (RSN 2)
    *dot1xMsgTask: Jul 18 10:41:12.955: 00:40:96:b8:78:7a Adding BSSID 10:8c:cf:78:93:87 to PMKID cache for station 00:40:96:b8:78:7a
    *dot1xMsgTask: Jul 18 10:41:12.955: New PMKID: (16)
    *dot1xMsgTask: Jul 18 10:41:12.956:      [0000] 4a 0c ea 60 5c 8c 76 2a ee 47 50 bd ad 58 e0 d9
    *dot1xMsgTask: Jul 18 10:41:12.956: 00:40:96:b8:78:7a Initiating RSN PSK to mobile 00:40:96:b8:78:7a
    *dot1xMsgTask: Jul 18 10:41:12.956: 00:40:96:b8:78:7a dot1x - moving mobile 00:40:96:b8:78:7a into Force Auth state
    *dot1xMsgTask: Jul 18 10:41:12.956: 00:40:96:b8:78:7a Skipping EAP-Success to mobile 00:40:96:b8:78:7a
    *dot1xMsgTask: Jul 18 10:41:12.956: Including PMKID in M1  (16)
    *dot1xMsgTask: Jul 18 10:41:12.956:      [0000] 4a 0c ea 60 5c 8c 76 2a ee 47 50 bd ad 58 e0 d9
    *dot1xMsgTask: Jul 18 10:41:12.956: 00:40:96:b8:78:7a Starting key exchange to mobile 00:40:96:b8:78:7a, data packets will be dropped
    *dot1xMsgTask: Jul 18 10:41:12.956: 00:40:96:b8:78:7a Sending EAPOL-Key Message to mobile 00:40:96:b8:78:7a
                                  state INITPMK (message 1), replay counter 00.00.00.00.00.00.00.00
    *osapiBsnTimer: Jul 18 10:41:13.961: 00:40:96:b8:78:7a 802.1x 'timeoutEvt' Timer expired for station 00:40:96:b8:78:7a and for message = M2
    *dot1xMsgTask: Jul 18 10:41:13.965: 00:40:96:b8:78:7a Retransmit 1 of EAPOL-Key M1 (length 121) for mobile 00:40:96:b8:78:7a
    *osapiBsnTimer: Jul 18 10:41:14.961: 00:40:96:b8:78:7a 802.1x 'timeoutEvt' Timer expired for station 00:40:96:b8:78:7a and for message = M2
    *dot1xMsgTask: Jul 18 10:41:14.962: 00:40:96:b8:78:7a Retransmit 2 of EAPOL-Key M1 (length 121) for mobile 00:40:96:b8:78:7a
    *apfLbsTask: Jul 18 10:41:15.762: 00:40:96:b8:78:7a Copy AP LOCP - mode:0 slotId:0, apMac 0x10:8c:cf:78:93:80
    *apfLbsTask: Jul 18 10:41:15.762: 00:40:96:b8:78:7a Copy WLAN LOCP EssIndex:11 aid:1 ssid:RUMCWireless-S
    *apfLbsTask: Jul 18 10:41:15.762: 00:40:96:b8:78:7a Copy Security LOCP ecypher:0x0 ptype:0x2, p:0x1, eaptype:0x6 w:0x1 aalg:0x0, PMState: 8021X_REQD
    *apfLbsTask: Jul 18 10:41:15.762: 00:40:96:b8:78:7a Copy 802.11 LOCP a:0x0 b:0x0 c:0x0 d:0x0 e:0x1 protocol2:0x2 statuscode 0, reasoncode 1, status 3
    *apfLbsTask: Jul 18 10:41:15.762: 00:40:96:b8:78:7a Copy CCX LOCP 5
    *apfLbsTask: Jul 18 10:41:15.762: 00:40:96:b8:78:7a Copy MobilityData LOCP status:0, anchorip:0x0
    *osapiBsnTimer: Jul 18 10:41:15.961: 00:40:96:b8:78:7a 802.1x 'timeoutEvt' Timer expired for station 00:40:96:b8:78:7a and for message = M2
    *dot1xMsgTask: Jul 18 10:41:15.965: 00:40:96:b8:78:7a Retransmit failure for EAPOL-Key M1 to mobile 00:40:96:b8:78:7a, retransmit count 3, mscb deauth count 1
    *dot1xMsgTask: Jul 18 10:41:15.967: 00:40:96:b8:78:7a Sent Deauthenticate to mobile on BSSID 10:8c:cf:78:93:80 slot 0(caller 1x_ptsm.c:534)
    *dot1xMsgTask: Jul 18 10:41:15.967: 00:40:96:b8:78:7a Scheduling deletion of Mobile Station:  (callerId: 57) in 10 seconds
    *apfMsConnTask_0: Jul 18 10:41:19.491: 00:40:96:b8:78:7a Association received from mobile on AP 10:8c:cf:78:93:80
    *apfMsConnTask_0: Jul 18 10:41:19.491: 00:40:96:b8:78:7a 0.0.0.0 8021X_REQD (3) Changing ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:1626)
    *apfMsConnTask_0: Jul 18 10:41:19.492: 00:40:96:b8:78:7a Applying site-specific IPv6 override for station 00:40:96:b8:78:7a - vapId 11, site 'TWR-5', interface 'pharmwireless'
    *apfMsConnTask_0: Jul 18 10:41:19.492: 00:40:96:b8:78:7a Applying IPv6 Interface Policy for station 00:40:96:b8:78:7a - vlan 274, interface id 12, interface 'pharmwireless'
    *apfMsConnTask_0: Jul 18 10:41:19.492: 00:40:96:b8:78:7a Applying site-specific override for station 00:40:96:b8:78:7a - vapId 11, site 'TWR-5', interface 'pharmwireless'
    *apfMsConnTask_0: Jul 18 10:41:19.492: 00:40:96:b8:78:7a 0.0.0.0 8021X_REQD (3) Changing ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:1626)
    *apfMsConnTask_0: Jul 18 10:41:19.492: 00:40:96:b8:78:7a STA - rates (6): 24 36 48 72 96 108 0 0 0 0 0 0 0 0 0 0
    *apfMsConnTask_0: Jul 18 10:41:19.492: 00:40:96:b8:78:7a Processing RSN IE type 48, length 38 for mobile 00:40:96:b8:78:7a
    *apfMsConnTask_0: Jul 18 10:41:19.492: 00:40:96:b8:78:7a 0.0.0.0 8021X_REQD (3) Initializing policy
    *apfMsConnTask_0: Jul 18 10:41:19.492: 00:40:96:b8:78:7a 0.0.0.0 8021X_REQD (3) Change state to AUTHCHECK (2) last state 8021X_REQD (3)
    *apfMsConnTask_0: Jul 18 10:41:19.492: 00:40:96:b8:78:7a 0.0.0.0 AUTHCHECK (2) Change state to 8021X_REQD (3) last state 8021X_REQD (3)
    *apfMsConnTask_0: Jul 18 10:41:19.492: 00:40:96:b8:78:7a 0.0.0.0 8021X_REQD (3) DHCP Not required on AP 10:8c:cf:78:93:80 vapId 11 apVapId 8for this client
    *apfMsConnTask_0: Jul 18 10:41:19.492: 00:40:96:b8:78:7a Not Using WMM Compliance code qosCap 00
    *apfMsConnTask_0: Jul 18 10:41:19.492: 00:40:96:b8:78:7a 0.0.0.0 8021X_REQD (3) Plumbed mobile LWAPP rule on AP 10:8c:cf:78:93:80 vapId 11 apVapId 8
    *apfMsConnTask_0: Jul 18 10:41:19.492: 00:40:96:b8:78:7a apfPemAddUser2 (apf_policy.c:223) Changing state for mobile 00:40:96:b8:78:7a on AP 10:8c:cf:78:93:80 from Associated to Associated
    *apfMsConnTask_0: Jul 18 10:41:19.492: 00:40:96:b8:78:7a Scheduling deletion of Mobile Station:  (callerId: 49) in 1800 seconds
    *apfMsConnTask_0: Jul 18 10:41:19.492: 00:40:96:b8:78:7a Sending Assoc Response to station on BSSID 10:8c:cf:78:93:80 (status 0) ApVapId 8 Slot 0
    *apfMsConnTask_0: Jul 18 10:41:19.492: 00:40:96:b8:78:7a apfProcessAssocReq (apf_80211.c:5237) Changing state for mobile 00:40:96:b8:78:7a on AP 10:8c:cf:78:93:80 from Associated to Associated
    *dot1xMsgTask: Jul 18 10:41:19.494: 00:40:96:b8:78:7a Creating a PKC PMKID Cache entry for station 00:40:96:b8:78:7a (RSN 2)
    *dot1xMsgTask: Jul 18 10:41:19.494: 00:40:96:b8:78:7a Adding BSSID 10:8c:cf:78:93:87 to PMKID cache for station 00:40:96:b8:78:7a
    *dot1xMsgTask: Jul 18 10:41:19.494: New PMKID: (16)
    *dot1xMsgTask: Jul 18 10:41:19.494:      [0000] 4a 0c ea 60 5c 8c 76 2a ee 47 50 bd ad 58 e0 d9
    *dot1xMsgTask: Jul 18 10:41:19.494: 00:40:96:b8:78:7a Initiating RSN PSK to mobile 00:40:96:b8:78:7a
    *dot1xMsgTask: Jul 18 10:41:19.494: 00:40:96:b8:78:7a dot1x - moving mobile 00:40:96:b8:78:7a into Force Auth state
    *dot1xMsgTask: Jul 18 10:41:19.494: 00:40:96:b8:78:7a Skipping EAP-Success to mobile 00:40:96:b8:78:7a
    *dot1xMsgTask: Jul 18 10:41:19.494: Including PMKID in M1  (16)
    *dot1xMsgTask: Jul 18 10:41:19.494:      [0000] 4a 0c ea 60 5c 8c 76 2a ee 47 50 bd ad 58 e0 d9
    *dot1xMsgTask: Jul 18 10:41:19.494: 00:40:96:b8:78:7a Starting key exchange to mobile 00:40:96:b8:78:7a, data packets will be dropped
    *dot1xMsgTask: Jul 18 10:41:19.494: 00:40:96:b8:78:7a Sending EAPOL-Key Message to mobile 00:40:96:b8:78:7a
                                  state INITPMK (message 1), replay counter 00.00.00.00.00.00.00.00
    *osapiBsnTimer: Jul 18 10:41:20.561: 00:40:96:b8:78:7a 802.1x 'timeoutEvt' Timer expired for station 00:40:96:b8:78:7a and for message = M2
    *dot1xMsgTask: Jul 18 10:41:20.561: 00:40:96:b8:78:7a Retransmit 1 of EAPOL-Key M1 (length 121) for mobile 00:40:96:b8:78:7a
    *osapiBsnTimer: Jul 18 10:41:21.561: 00:40:96:b8:78:7a 802.1x 'timeoutEvt' Timer expired for station 00:40:96:b8:78:7a and for message = M2
    *dot1xMsgTask: Jul 18 10:41:21.561: 00:40:96:b8:78:7a Retransmit 2 of EAPOL-Key M1 (length 121) for mobile 00:40:96:b8:78:7a
    *osapiBsnTimer: Jul 18 10:41:22.561: 00:40:96:b8:78:7a 802.1x 'timeoutEvt' Timer expired for station 00:40:96:b8:78:7a and for message = M2
    *dot1xMsgTask: Jul 18 10:41:22.562: 00:40:96:b8:78:7a Retransmit failure for EAPOL-Key M1 to mobile 00:40:96:b8:78:7a, retransmit count 3, mscb deauth count 2
    *dot1xMsgTask: Jul 18 10:41:22.563: 00:40:96:b8:78:7a Sent Deauthenticate to mobile on BSSID 10:8c:cf:78:93:80 slot 0(caller 1x_ptsm.c:534)
    *dot1xMsgTask: Jul 18 10:41:22.563: 00:40:96:b8:78:7a Scheduling deletion of Mobile Station:  (callerId: 57) in 10 seconds
    *apfLbsTask: Jul 18 10:41:23.762: 00:40:96:b8:78:7a Copy AP LOCP - mode:0 slotId:0, apMac 0x10:8c:cf:78:93:80
    *apfLbsTask: Jul 18 10:41:23.762: 00:40:96:b8:78:7a Copy WLAN LOCP EssIndex:11 aid:1 ssid:RUMCWireless-S
    *apfLbsTask: Jul 18 10:41:23.762: 00:40:96:b8:78:7a Copy Security LOCP ecypher:0x0 ptype:0x2, p:0x1, eaptype:0x6 w:0x1 aalg:0x0, PMState: 8021X_REQD
    *apfLbsTask: Jul 18 10:41:23.762: 00:40:96:b8:78:7a Copy 802.11 LOCP a:0x0 b:0x0 c:0x0 d:0x0 e:0x1 protocol2:0x2 statuscode 0, reasoncode 1, status 3
    *apfLbsTask: Jul 18 10:41:23.762: 00:40:96:b8:78:7a Copy CCX LOCP 5
    *apfLbsTask: Jul 18 10:41:23.762: 00:40:96:b8:78:7a Copy MobilityData LOCP status:0, anchorip:0x0
    *apfMsConnTask_0: Jul 18 10:41:26.116: 00:40:96:b8:78:7a Association received from mobile on AP 10:8c:cf:78:93:80
    *apfMsConnTask_0: Jul 18 10:41:26.117: 00:40:96:b8:78:7a 0.0.0.0 8021X_REQD (3) Changing ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:1626)
    *apfMsConnTask_0: Jul 18 10:41:26.117: 00:40:96:b8:78:7a Applying site-specific IPv6 override for station 00:40:96:b8:78:7a - vapId 11, site 'TWR-5', interface 'pharmwireless'
    *apfMsConnTask_0: Jul 18 10:41:26.117: 00:40:96:b8:78:7a Applying IPv6 Interface Policy for station 00:40:96:b8:78:7a - vlan 274, interface id 12, interface 'pharmwireless'
    *apfMsConnTask_0: Jul 18 10:41:26.117: 00:40:96:b8:78:7a Applying site-specific override for station 00:40:96:b8:78:7a - vapId 11, site 'TWR-5', interface 'pharmwireless'
    *apfMsConnTask_0: Jul 18 10:41:26.117: 00:40:96:b8:78:7a 0.0.0.0 8021X_REQD (3) Changing ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:1626)
    *apfMsConnTask_0: Jul 18 10:41:26.117: 00:40:96:b8:78:7a STA - rates (6): 24 36 48 72 96 108 0 0 0 0 0 0 0 0 0 0
    *apfMsConnTask_0: Jul 18 10:41:26.117: 00:40:96:b8:78:7a Processing RSN IE type 48, length 38 for mobile 00:40:96:b8:78:7a
    *apfMsConnTask_0: Jul 18 10:41:26.117: 00:40:96:b8:78:7a 0.0.0.0 8021X_REQD (3) Initializing policy
    *apfMsConnTask_0: Jul 18 10:41:26.117: 00:40:96:b8:78:7a 0.0.0.0 8021X_REQD (3) Change state to AUTHCHECK (2) last state 8021X_REQD (3)
    *apfMsConnTask_0: Jul 18 10:41:26.117: 00:40:96:b8:78:7a 0.0.0.0 AUTHCHECK (2) Change state to 8021X_REQD (3) last state 8021X_REQD (3)
    *apfMsConnTask_0: Jul 18 10:41:26.117: 00:40:96:b8:78:7a 0.0.0.0 8021X_REQD (3) DHCP Not required on AP 10:8c:cf:78:93:80 vapId 11 apVapId 8for this client
    *apfMsConnTask_0: Jul 18 10:41:26.117: 00:40:96:b8:78:7a Not Using WMM Compliance code qosCap 00
    *apfMsConnTask_0: Jul 18 10:41:26.117: 00:40:96:b8:78:7a 0.0.0.0 8021X_REQD (3) Plumbed mobile LWAPP rule on AP 10:8c:cf:78:93:80 vapId 11 apVapId 8
    *apfMsConnTask_0: Jul 18 10:41:26.117: 00:40:96:b8:78:7a apfPemAddUser2 (apf_policy.c:223) Changing state for mobile 00:40:96:b8:78:7a on AP 10:8c:cf:78:93:80 from Associated to Associated
    *apfMsConnTask_0: Jul 18 10:41:26.117: 00:40:96:b8:78:7a Scheduling deletion of Mobile Station:  (callerId: 49) in 1800 seconds
    *apfMsConnTask_0: Jul 18 10:41:26.117: 00:40:96:b8:78:7a Sending Assoc Response to station on BSSID 10:8c:cf:78:93:80 (status 0) ApVapId 8 Slot 0
    *apfMsConnTask_0: Jul 18 10:41:26.117: 00:40:96:b8:78:7a apfProcessAssocReq (apf_80211.c:5237) Changing state for mobile 00:40:96:b8:78:7a on AP 10:8c:cf:78:93:80 from Associated to Associated
    *dot1xMsgTask: Jul 18 10:41:26.120: 00:40:96:b8:78:7a Creating a PKC PMKID Cache entry for station 00:40:96:b8:78:7a (RSN 2)
    *dot1xMsgTask: Jul 18 10:41:26.120: 00:40:96:b8:78:7a Adding BSSID 10:8c:cf:78:93:87 to PMKID cache for station 00:40:96:b8:78:7a
    *dot1xMsgTask: Jul 18 10:41:26.120: New PMKID: (16)
    *dot1xMsgTask: Jul 18 10:41:26.120:      [0000] 4a 0c ea 60 5c 8c 76 2a ee 47 50 bd ad 58 e0 d9
    *dot1xMsgTask: Jul 18 10:41:26.120: 00:40:96:b8:78:7a Initiating RSN PSK to mobile 00:40:96:b8:78:7a
    *dot1xMsgTask: Jul 18 10:41:26.120: 00:40:96:b8:78:7a dot1x - moving mobile 00:40:96:b8:78:7a into Force Auth state
    *dot1xMsgTask: Jul 18 10:41:26.120: 00:40:96:b8:78:7a Skipping EAP-Success to mobile 00:40:96:b8:78:7a
    *dot1xMsgTask: Jul 18 10:41:26.120: Including PMKID in M1  (16)
    *dot1xMsgTask: Jul 18 10:41:26.120:      [0000] 4a 0c ea 60 5c 8c 76 2a ee 47 50 bd ad 58 e0 d9
    *dot1xMsgTask: Jul 18 10:41:26.120: 00:40:96:b8:78:7a Starting key exchange to mobile 00:40:96:b8:78:7a, data packets will be dropped
    *dot1xMsgTask: Jul 18 10:41:26.120: 00:40:96:b8:78:7a Sending EAPOL-Key Message to mobile 00:40:96:b8:78:7a
                                  state INITPMK (message 1), replay counter 00.00.00.00.00.00.00.00
    *osapiBsnTimer: Jul 18 10:41:27.161: 00:40:96:b8:78:7a 802.1x 'timeoutEvt' Timer expired for station 00:40:96:b8:78:7a and for message = M2
    *dot1xMsgTask: Jul 18 10:41:27.162: 00:40:96:b8:78:7a Retransmit 1 of EAPOL-Key M1 (length 121) for mobile 00:40:96:b8:78:7a
    *osapiBsnTimer: Jul 18 10:41:28.161: 00:40:96:b8:78:7a 802.1x 'timeoutEvt' Timer expired for station 00:40:96:b8:78:7a and for message = M2
    *dot1xMsgTask: Jul 18 10:41:28.162: 00:40:96:b8:78:7a Retransmit 2 of EAPOL-Key M1 (length 121) for mobile 00:40:96:b8:78:7a
    *osapiBsnTimer: Jul 18 10:41:29.161: 00:40:96:b8:78:7a 802.1x 'timeoutEvt' Timer expired for station 00:40:96:b8:78:7a and for message = M2
    *dot1xMsgTask: Jul 18 10:41:29.162: 00:40:96:b8:78:7a Retransmit failure for EAPOL-Key M1 to mobile 00:40:96:b8:78:7a, retransmit count 3, mscb deauth count 3
    *dot1xMsgTask: Jul 18 10:41:29.162: 00:40:96:b8:78:7a Blacklisting (if enabled) mobile 00:40:96:b8:78:7a
    *dot1xMsgTask: Jul 18 10:41:29.162: 00:40:96:b8:78:7a apfBlacklistMobileStationEntry2 (apf_ms.c:4294) Changing state for mobile 00:40:96:b8:78:7a on AP 10:8c:cf:78:93:80 from Associated to Exclusion-list (1)
    *dot1xMsgTask: Jul 18 10:41:29.162: 00:40:96:b8:78:7a Scheduling deletion of Mobile Station:  (callerId: 44) in 10 seconds
    *dot1xMsgTask: Jul 18 10:41:29.163: 00:40:96:b8:78:7a 0.0.0.0 8021X_REQD (3) Change state to START (0) last state 8021X_REQD (3)
    *dot1xMsgTask: Jul 18 10:41:29.163: 00:40:96:b8:78:7a 0.0.0.0 START (0) Reached FAILURE: from line 4025
    *dot1xMsgTask: Jul 18 10:41:29.164: 00:40:96:b8:78:7a Scheduling deletion of Mobile Station:  (callerId: 9) in 10 seconds
    *apfLbsTask: Jul 18 10:41:31.766: 00:40:96:b8:78:7a Copy AP LOCP - mode:0 slotId:0, apMac 0x10:8c:cf:78:93:80
    *apfLbsTask: Jul 18 10:41:31.766: 00:40:96:b8:78:7a Copy WLAN LOCP EssIndex:11 aid:1 ssid:RUMCWireless-S
    *apfLbsTask: Jul 18 10:41:31.766: 00:40:96:b8:78:7a Copy Security LOCP ecypher:0x0 ptype:0x2, p:0x1, eaptype:0x6 w:0x1 aalg:0x0, PMState:      START
    *apfLbsTask: Jul 18 10:41:31.766: 00:40:96:b8:78:7a Copy 802.11 LOCP a:0x0 b:0x0 c:0x0 d:0x0 e:0x1 protocol2:0x2 statuscode 0, reasoncode 1, status 8
    *apfLbsTask: Jul 18 10:41:31.766: 00:40:96:b8:78:7a Copy CCX LOCP 5
    *apfLbsTask: Jul 18 10:41:31.766: 00:40:96:b8:78:7a Copy MobilityData LOCP status:0, anchorip:0x0
    *osapiBsnTimer: Jul 18 10:41:39.165: 00:40:96:b8:78:7a apfMsExpireCallback (apf_ms.c:608) Expiring Mobile!
    *apfReceiveTask: Jul 18 10:41:39.166: 00:40:96:b8:78:7a Scheduling deletion of Mobile Station:  (callerId: 46) in 60 seconds
    *apfReceiveTask: Jul 18 10:41:39.166: 00:40:96:b8:78:7a apfMsExpireMobileStation (apf_ms.c:5131) Changing state for mobile 00:40:96:b8:78:7a on AP 10:8c:cf:78:93:80 from Exclusion-list (1) to Exclusion-list (2)
    *apfReceiveTask: Jul 18 10:41:39.166: 00:40:96:b8:78:7a 0.0.0.0 START (0) Deleted mobile LWAPP rule on AP [10:8c:cf:78:93:80]
    *apfMsConnTask_0: Jul 18 10:41:51.799: 00:40:96:b8:78:7a Ignoring assoc request due to mobile in exclusion list or marked for deletion
    *apfMsConnTask_0: Jul 18 10:41:52.313: 00:40:96:b8:78:7a Ignoring assoc request due to mobile in exclusion list or marked for deletion
    *apfMsConnTask_0: Jul 18 10:41:53.316: 00:40:96:b8:78:7a Ignoring assoc request due to mobile in exclusion list or marked for deletion
    *apfMsConnTask_0: Jul 18 10:41:54.320: 00:40:96:b8:78:7a Ignoring assoc request due to mobile in exclusion list or marked for deletion
    *apfMsConnTask_0: Jul 18 10:41:55.323: 00:40:96:b8:78:7a Ignoring assoc request due to mobile in exclusion list or marked for deletion
    *apfMsConnTask_0: Jul 18 10:41:56.326: 00:40:96:b8:78:7a Ignoring assoc request due to mobile in exclusion list or marked for deletion
    *apfMsConnTask_6: Jul 18 10:41:59.292: 00:40:96:b8:78:7a Ignoring assoc request due to mobile in exclusion list or marked for deletion
    *apfMsConnTask_6: Jul 18 10:41:59.339: 00:40:96:b8:78:7a Ignoring assoc request due to mobile in exclusion list or marked for deletion
    *apfMsConnTask_6: Jul 18 10:42:00.342: 00:40:96:b8:78:7a Ignoring assoc request due to mobile in exclusion list or marked for deletion
    *apfMsConnTask_6: Jul 18 10:42:01.346: 00:40:96:b8:78:7a Ignoring assoc request due to mobile in exclusion list or marked for deletion
    *apfMsConnTask_6: Jul 18 10:42:02.349: 00:40:96:b8:78:7a Ignoring assoc request due to mobile in exclusion list or marked for deletion
    *apfMsConnTask_6: Jul 18 10:42:03.352: 00:40:96:b8:78:7a Ignoring assoc request due to mobile in exclusion list or marked for deletion
    *spamApTask0: Jul 18 10:42:07.907: 00:40:96:b8:78:7a Received Idle-Timeout from AP 10:8c:cf:78:93:80, slot 0 for STA 00:40:96:b8:78:7a
    *spamApTask0: Jul 18 10:42:07.907: 00:40:96:b8:78:7a Ignoring delete request from AP due to mobile in exclusion list or marked for deletion already
    *apfMsConnTask_0: Jul 18 10:42:08.127: 00:40:96:b8:78:7a Ignoring assoc request due to mobile in exclusion list or marked for deletion
    *apfMsConnTask_0: Jul 18 10:42:08.370: 00:40:96:b8:78:7a Ignoring assoc request due to mobile in exclusion list or marked for deletion
    *apfMsConnTask_0: Jul 18 10:42:09.373: 00:40:96:b8:78:7a Ignoring assoc request due to mobile in exclusion list or marked for deletion
    *apfMsConnTask_0: Jul 18 10:42:10.377: 00:40:96:b8:78:7a Ignoring assoc request due to mobile in exclusion list or marked for deletion
    *apfMsConnTask_0: Jul 18 10:42:11.380: 00:40:96:b8:78:7a Ignoring assoc request due to mobile in exclusion list or marked for deletion
    *apfMsConnTask_0: Jul 18 10:42:12.383: 00:40:96:b8:78:7a Ignoring assoc request due to mobile in exclusion list or marked for deletion
    *apfMsConnTask_5: Jul 18 10:42:27.323: 00:40:96:b8:78:7a Ignoring assoc request due to mobile in exclusion list or marked for deletion
    *apfMsConnTask_5: Jul 18 10:42:28.438: 00:40:96:b8:78:7a Ignoring assoc request due to mobile in exclusion list or marked for deletion
    *apfMsConnTask_5: Jul 18 10:42:29.441: 00:40:96:b8:78:7a Ignoring assoc request due to mobile in exclusion list or marked for deletion
    *apfMsConnTask_5: Jul 18 10:42:30.445: 00:40:96:b8:78:7a Ignoring assoc request due to mobile in exclusion list or marked for deletion
    *apfMsConnTask_5: Jul 18 10:42:31.448: 00:40:96:b8:78:7a Ignoring assoc request due to mobile in exclusion list or marked for deletion
    *apfMsConnTask_4: Jul 18 10:42:36.045: 00:40:96:b8:78:7a Ignoring assoc request due to mobile in exclusion list or marked for deletion
    *apfMsConnTask_4: Jul 18 10:42:36.467: 00:40:96:b8:78:7a Ignoring assoc request due to mobile in exclusion list or marked for deletion
    *apfMsConnTask_4: Jul 18 10:42:37.470: 00:40:96:b8:78:7a Ignoring assoc request due to mobile in exclusion list or marked for deletion
    *apfMsConnTask_4: Jul 18 10:42:38.474: 00:40:96:b8:78:7a Ignoring assoc request due to mobile in exclusion list or marked for deletion
    *osapiBsnTimer: Jul 18 10:42:39.169: 00:40:96:b8:78:7a apfMsExpireCallback (apf_ms.c:608) Expiring Mobile!
    *apfReceiveTask: Jul 18 10:42:39.170: 00:40:96:b8:78:7a apfMsAssoStateDec
    *apfReceiveTask: Jul 18 10:42:39.170: 00:40:96:b8:78:7a Deleting mobile on AP 10:8c:cf:78:93:80(0)
    Can anyone tell me why this is happening?
    Thank You

    Auth succeeded from AAA server side but there is a problem with 4-way handshake. It is obvious the problem is with the client because it does not reply the message 2 of the handshake.
    What is this client?
    Try upgrading the driver or the firmware. That sort it out.
    Sent from Cisco Technical Support iPad App

  • Cisco ISE 1.2 & Cisco WLC 5508 v7.6

    Hi all,
    we are planning to upgrade our WLC to 7.6 to fix a bug with FlexConnect Client ACLs but I have just seen on the Cisco ISE Compatibility table that the it only recommends up to v7.5 of the WLC 5508...
    Cisco have told me to steer clear of 7.5 as it is in a defferred status, so does anyone know, or have running in a lab or production, ISE1.2 with a 5508 WLC v7.6 NAD ?
    I would much rather know of any issues people are experiencing before hand than to have to go through a software upgrade and then rollback.
    Thanks all
    Mario De Rosa

    Hi Neno,
    right I have this almost working now.
    I have simplified the setup. I am not going to do any client provisioning at the moment.
    So I can connect to the corporate SSID using EAP-TLS and I can successfully push the branch data VLAN upon successful authorisation.
    Now I am trying to introduce the posture element & per user ACLs.
    I have defined the redirect ACL & Flex ACL on the vWLC however the NAC agent will not pop-up. The client is in the right VLAN and the redirect ACL seems to be getting applied as the client does get an IP through DHCP. However, the client cannot ping the ISE or access the guest portal when I open the browser.
    DNS resolution seems to be working fine.
    VLAN220 is my datacentre VLAN which the Management Interface on the controller is plugged in to.
    VLAN10 is the branch DATA VLAN.
    below is some output to give you some more details...
    (Cisco Controller) >show client detail 00:24:d6:97:b3:be
    Client MAC Address............................... 00:24:d6:97:b3:be
    Client Username ................................. [email protected]
    AP MAC Address................................... 18:33:9d:f0:21:80
    AP Name.......................................... test-flex-ap
    AP radio slot Id................................. 0
    Client State..................................... Associated
    Client NAC OOB State............................. Access
    Wireless LAN Id.................................. 2
    Hotspot (802.11u)................................ Not Supported
    BSSID............................................ 18:33:9d:f0:21:81
    Connected For ................................... 128 secs
    Channel.......................................... 6
    IP Address....................................... 10.130.130.120
    Gateway Address.................................. 10.130.130.1
    Netmask.......................................... 255.255.255.0
    IPv6 Address..................................... fe80::f524:1910:69f0:9482
    Association Id................................... 1
    Authentication Algorithm......................... Open System
    Reason Code...................................... 1
    Status Code...................................... 0
    Client CCX version............................... 4
    Client E2E version............................... 1
    --More-- or (q)uit
    Re-Authentication Timeout........................ 1651
    QoS Level........................................ Silver
    Avg data Rate.................................... 0
    Burst data Rate.................................. 0
    Avg Real time data Rate.......................... 0
    Burst Real Time data Rate........................ 0
    802.1P Priority Tag.............................. disabled
    CTS Security Group Tag........................... Not Applicable
    KTS CAC Capability............................... No
    WMM Support...................................... Enabled
      APSD ACs.......................................  BK  BE  VI  VO
    Power Save....................................... OFF
    Current Rate..................................... m13
    Supported Rates.................................. 1.0,2.0,5.5,11.0,6.0,9.0,
        ............................................. 12.0,18.0,24.0,36.0,48.0,
        ............................................. 54.0
    Mobility State................................... Local
    Mobility Move Count.............................. 0
    Security Policy Completed........................ No
    Policy Manager State............................. POSTURE_REQD
    Policy Manager Rule Created...................... Yes
    AAA Override ACL Name............................ POSTURE_REDIRECT_ACL
    AAA Override ACL Applied Status.................. Yes
    --More-- or (q)uit
    AAA Override Flex ACL Name....................... POSTURE_REDIRECT_ACL
    AAA Override Flex ACL Applied Status............. Yes
    AAA URL redirect................................. https://pdc-ise-man01.kier.group:8443/guestportal/gateway?sessionId=c8dc800a00000005b3e7e953&action=cpp
    Audit Session ID................................. c8dc800a00000005b3e7e953
    AAA Role Type.................................... none
    Local Policy Applied............................. none
    IPv4 ACL Name.................................... none
    FlexConnect ACL Applied Status................... Yes
    IPv4 ACL Applied Status.......................... Unavailable
    IPv6 ACL Name.................................... none
    IPv6 ACL Applied Status.......................... Unavailable
    Layer2 ACL Name.................................. none
    Layer2 ACL Applied Status........................ Unavailable
    mDNS Status...................................... Disabled
    mDNS Profile Name................................ none
    No. of mDNS Services Advertised.................. 0
    Policy Type...................................... WPA2
    Authentication Key Management.................... 802.1x
    Encryption Cipher................................ CCMP (AES)
    Protected Management Frame ...................... No
    Management Frame Protection...................... No
    EAP Type......................................... EAP-TLS
    FlexConnect Data Switching....................... Local
    --More-- or (q)uit
    FlexConnect Dhcp Status.......................... Local
    FlexConnect Vlan Based Central Switching......... No
    FlexConnect Authentication....................... Central
    Quarantine VLAN.................................. 0
    Access VLAN...................................... 220
    Client Capabilities:
          CF Pollable................................ Not implemented
          CF Poll Request............................ Not implemented
          Short Preamble............................. Implemented
          PBCC....................................... Not implemented
          Channel Agility............................ Not implemented
          Listen Interval............................ 10
          Fast BSS Transition........................ Not implemented
    Client Wifi Direct Capabilities:
          WFD capable................................ No
          Manged WFD capable......................... No
          Cross Connection Capable................... No
          Support Concurrent Operation............... No
    Fast BSS Transition Details:
    Client Statistics:
          Number of Bytes Received................... 33698
          Number of Bytes Sent....................... 19397
          Total Number of Bytes Sent................. 19397
    --More-- or (q)uit
          Total Number of Bytes Recv................. 33698
          Number of Bytes Sent (last 90s)............ 19397
          Number of Bytes Recv (last 90s)............ 33698
          Number of Packets Received................. 283
          Number of Packets Sent..................... 147
          Number of Interim-Update Sent.............. 0
          Number of EAP Id Request Msg Timeouts...... 0
          Number of EAP Id Request Msg Failures...... 0
          Number of EAP Request Msg Timeouts......... 0
          Number of EAP Request Msg Failures......... 0
          Number of EAP Key Msg Timeouts............. 0
          Number of EAP Key Msg Failures............. 0
          Number of Data Retries..................... 53
          Number of RTS Retries...................... 0
          Number of Duplicate Received Packets....... 2
          Number of Decrypt Failed Packets........... 0
          Number of Mic Failured Packets............. 0
          Number of Mic Missing Packets.............. 0
          Number of RA Packets Dropped............... 0
          Number of Policy Errors.................... 0
          Radio Signal Strength Indicator............ -42 dBm
          Signal to Noise Ratio...................... 41 dB
    Client Rate Limiting Statistics:
    --More-- or (q)uit
          Number of Data Packets Recieved............ 0
          Number of Data Rx Packets Dropped.......... 0
          Number of Data Bytes Recieved.............. 0
          Number of Data Rx Bytes Dropped............ 0
          Number of Realtime Packets Recieved........ 0
          Number of Realtime Rx Packets Dropped...... 0
          Number of Realtime Bytes Recieved.......... 0
          Number of Realtime Rx Bytes Dropped........ 0
          Number of Data Packets Sent................ 0
          Number of Data Tx Packets Dropped.......... 0
          Number of Data Bytes Sent.................. 0
          Number of Data Tx Bytes Dropped............ 0
          Number of Realtime Packets Sent............ 0
          Number of Realtime Tx Packets Dropped...... 0
          Number of Realtime Bytes Sent.............. 0
          Number of Realtime Tx Bytes Dropped........ 0
    Nearby AP Statistics:
          test-flex-ap(slot 0)
            antenna0: 14 secs ago.................... -51 dBm
            antenna1: 14 secs ago.................... -37 dBm
          test-flex-ap(slot 1)
            antenna0: 14 secs ago.................... -51 dBm
            antenna1: 14 secs ago.................... -54 dBm
    --More-- or (q)uit
    DNS Server details:
          DNS server IP ............................. 10.0.17.31
          DNS server IP ............................. 10.0.17.43
    Assisted Roaming Prediction List details:
     Client Dhcp Required:     False
    Allowed (URL)IP Addresses
    (Cisco Controller) >
    (Cisco Controller) >show wlan 2
    WLAN Identifier.................................. 2
    Profile Name..................................... Demo1x
    Network Name (SSID).............................. Demo1x
    Status........................................... Enabled
    MAC Filtering.................................... Disabled
    Broadcast SSID................................... Enabled
    AAA Policy Override.............................. Enabled
    Network Admission Control
    Client Profiling Status
        Radius Profiling ............................ Disabled
         DHCP ....................................... Disabled
         HTTP ....................................... Disabled
        Local Profiling ............................. Disabled
         DHCP ....................................... Disabled
         HTTP ....................................... Disabled
      Radius-NAC State............................... Enabled
      SNMP-NAC State................................. Disabled
      Quarantine VLAN................................ 0
    Maximum number of Associated Clients............. 0
    Maximum number of Clients per AP Radio........... 200
    --More-- or (q)uit
    Number of Active Clients......................... 1
    Exclusionlist Timeout............................ 60 seconds
    Session Timeout.................................. 1800 seconds
    User Idle Timeout................................ Disabled
    Sleep Client..................................... disable
    Sleep Client Timeout............................. 12 hours
    User Idle Threshold.............................. 0 Bytes
    NAS-identifier................................... mario-test-flex-vwlc
    CHD per WLAN..................................... Enabled
    Webauth DHCP exclusion........................... Disabled
    Interface........................................ management
    Multicast Interface.............................. Not Configured
    WLAN IPv4 ACL.................................... unconfigured
    WLAN IPv6 ACL.................................... unconfigured
    WLAN Layer2 ACL.................................. unconfigured
    mDNS Status...................................... Disabled
    mDNS Profile Name................................ unconfigured
    DHCP Server...................................... Default
    DHCP Address Assignment Required................. Disabled
    Static IP client tunneling....................... Disabled
    Quality of Service............................... Silver
    Per-SSID Rate Limits............................. Upstream      Downstream
    Average Data Rate................................   0             0
    --More-- or (q)uit
    Average Realtime Data Rate.......................   0             0
    Burst Data Rate..................................   0             0
    Burst Realtime Data Rate.........................   0             0
    Per-Client Rate Limits........................... Upstream      Downstream
    Average Data Rate................................   0             0
    Average Realtime Data Rate.......................   0             0
    Burst Data Rate..................................   0             0
    Burst Realtime Data Rate.........................   0             0
    Scan Defer Priority.............................. 4,5,6
    Scan Defer Time.................................. 100 milliseconds
    WMM.............................................. Allowed
    WMM UAPSD Compliant Client Support............... Disabled
    Media Stream Multicast-direct.................... Disabled
    CCX - AironetIe Support.......................... Enabled
    CCX - Gratuitous ProbeResponse (GPR)............. Disabled
    CCX - Diagnostics Channel Capability............. Disabled
    Dot11-Phone Mode (7920).......................... Disabled
    Wired Protocol................................... None
    Passive Client Feature........................... Disabled
    Peer-to-Peer Blocking Action..................... Disabled
    Radio Policy..................................... All
    DTIM period for 802.11a radio.................... 1
    DTIM period for 802.11b radio.................... 1
    --More-- or (q)uit
    Radius Servers
       Authentication................................ 10.0.16.111 1812
       Accounting.................................... 10.131.16.111 1813
          Interim Update............................. Disabled
          Framed IPv6 Acct AVP ...................... Prefix
       Dynamic Interface............................. Disabled
       Dynamic Interface Priority.................... wlan
    Local EAP Authentication......................... Disabled
    Security
       802.11 Authentication:........................ Open System
       FT Support.................................... Disabled
       Static WEP Keys............................... Disabled
       802.1X........................................ Disabled
       Wi-Fi Protected Access (WPA/WPA2)............. Enabled
          WPA (SSN IE)............................... Disabled
          WPA2 (RSN IE).............................. Enabled
             TKIP Cipher............................. Disabled
             AES Cipher.............................. Enabled
                                                                   Auth Key Management
             802.1x.................................. Enabled
             PSK..................................... Disabled
             CCKM.................................... Disabled
    --More-- or (q)uit
             FT-1X(802.11r).......................... Disabled
             FT-PSK(802.11r)......................... Disabled
             PMF-1X(802.11w)......................... Disabled
             PMF-PSK(802.11w)........................ Disabled
          FT Reassociation Timeout................... 20
          FT Over-The-DS mode........................ Enabled
          GTK Randomization.......................... Disabled
          SKC Cache Support.......................... Disabled
          CCKM TSF Tolerance......................... 1000
       WAPI.......................................... Disabled
       Wi-Fi Direct policy configured................ Disabled
       EAP-Passthrough............................... Disabled
       CKIP ......................................... Disabled
       Web Based Authentication...................... Disabled
       Web-Passthrough............................... Disabled
       Conditional Web Redirect...................... Disabled
       Splash-Page Web Redirect...................... Disabled
       Auto Anchor................................... Disabled
       FlexConnect Local Switching................... Enabled
       flexconnect Central Dhcp Flag................. Disabled
       flexconnect nat-pat Flag...................... Disabled
       flexconnect Dns Override Flag................. Disabled
       flexconnect PPPoE pass-through................ Disabled
    --More-- or (q)uit
       flexconnect local-switching IP-source-guar.... Disabled
       FlexConnect Vlan based Central Switching ..... Disabled
       FlexConnect Local Authentication.............. Disabled
       FlexConnect Learn IP Address.................. Enabled
       Client MFP.................................... Optional
       PMF........................................... Disabled
       PMF Association Comeback Time................. 1
       PMF SA Query RetryTimeout..................... 200
       Tkip MIC Countermeasure Hold-down Timer....... 60
       Eap-params.................................... Disabled
    AVC Visibilty.................................... Disabled
    AVC Profile Name................................. None
    Flow Monitor Name................................ None
    Split Tunnel (Printers).......................... Disabled
    Call Snooping.................................... Disabled
    Roamed Call Re-Anchor Policy..................... Disabled
    SIP CAC Fail Send-486-Busy Policy................ Disabled
    SIP CAC Fail Send Dis-Association Policy......... Disabled
    KTS based CAC Policy............................. Disabled
    Assisted Roaming Prediction Optimization......... Disabled
    802.11k Neighbor List............................ Disabled
    802.11k Neighbor List Dual Band.................. Disabled
    Band Select...................................... Disabled
    --More-- or (q)uit
    Load Balancing................................... Disabled
    Multicast Buffer................................. Disabled
     Mobility Anchor List
     WLAN ID     IP Address            Status
    802.11u........................................ Disabled
    MSAP Services.................................. Disabled
    Local Policy
    Priority  Policy Name
    (Cisco Controller) >
    when debugging the client during redirect, this is the output and I cannot spot anything wrong here...
    (Cisco Controller) >*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Adding mobile on LWAPP AP 18:33:9d:f0:21:80(1) 
    *apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Association received from mobile on BSSID 18:33:9d:f0:21:8e
    *apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Global 200 Clients are allowed to AP radio
    *apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Max Client Trap Threshold: 0  cur: 0
    *apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Rf profile 600 Clients are allowed to AP wlan
    *apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be override for default ap group, marking intgrp NULL
    *apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Applying Interface policy on Mobile, role Unassociated. Ms NAC State 0 Quarantine Vlan 0 Access Vlan 0
    *apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Re-applying interface policy for client 
    *apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be 0.0.0.0 START (0) Changing IPv4 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2219)
    *apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be 0.0.0.0 START (0) Changing IPv6 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2240)
    *apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be apfApplyWlanPolicy: Retaining the ACL recieved in AAA attributes 255 on mobile 
    *apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be apfApplyWlanPolicy: Apply WLAN Policy over PMIPv6 Client Mobility Type
    *apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be In processSsidIE:4850 setting Central switched to FALSE
    *apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Applying site-specific Local Bridging override for station 00:24:d6:97:b3:be - vapId 2, site 'default-group', interface 'management'
    *apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Applying Local Bridging Interface Policy for station 00:24:d6:97:b3:be - vlan 220, interface id 0, interface 'management'
    *apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be processSsidIE  statusCode is 0 and status is 0 
    *apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be processSsidIE  ssid_done_flag is 0 finish_flag is 0
    *apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be STA - rates (8): 140 18 152 36 176 72 96 108 0 0 0 0 0 0 0 0
    *apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be suppRates  statusCode is 0 and gotSuppRatesElement is 1 
    *apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Processing RSN IE type 48, length 22 for mobile 00:24:d6:97:b3:be
    *apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Received RSN IE with 0 PMKIDs from mobile 00:24:d6:97:b3:be
    *apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Setting active key cache index 8 ---> 8
    *apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be unsetting PmkIdValidatedByAp
    *apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Updating AID for REAP AP Client 18:33:9d:f0:21:80 - AID ===> 1
    *apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be 0.0.0.0 START (0) Initializing policy
    *apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be 0.0.0.0 START (0) Change state to AUTHCHECK (2) last state START (0)
    *apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be 0.0.0.0 AUTHCHECK (2) Change state to 8021X_REQD (3) last state AUTHCHECK (2)
    *apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Central switch is FALSE
    *apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be 0.0.0.0 8021X_REQD (3) DHCP required on AP 18:33:9d:f0:21:80 vapId 2 apVapId 2for this client
    *apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Not Using WMM Compliance code qosCap 00
    *apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be 0.0.0.0 8021X_REQD (3) Plumbed mobile LWAPP rule on AP 18:33:9d:f0:21:80 vapId 2 apVapId 2 flex-acl-name: 
    *apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be apfMsAssoStateInc
    *apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be apfPemAddUser2 (apf_policy.c:333) Changing state for mobile 00:24:d6:97:b3:be on AP 18:33:9d:f0:21:80 from Idle to Associated
    *apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be apfPemAddUser2:session timeout forstation 00:24:d6:97:b3:be - Session Tout 0, apfMsTimeOut '0' and sessionTimerRunning flag is  0 
    *apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Stopping deletion of Mobile Station: (callerId: 48)
    *apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Func: apfPemAddUser2, Ms Timeout = 0, Session Timeout = 0
    *apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Sending Assoc Response to station on BSSID 18:33:9d:f0:21:8e (status 0) ApVapId 2 Slot 1
    *apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be apfProcessAssocReq (apf_80211.c:8294) Changing state for mobile 00:24:d6:97:b3:be on AP 18:33:9d:f0:21:80 from Associated to Associated
    *spamApTask6: Aug 12 10:58:24.016: 00:24:d6:97:b3:be Sent 1x initiate message to multi thread task for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.016: 00:24:d6:97:b3:be EAP-PARAM Debug - eap-params for Wlan-Id :2 is disabled - applying Global eap timers and retries
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.016: 00:24:d6:97:b3:be Station 00:24:d6:97:b3:be setting dot1x reauth timeout = 1800
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.016: 00:24:d6:97:b3:be dot1x - moving mobile 00:24:d6:97:b3:be into Connecting state
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.016: 00:24:d6:97:b3:be Sending EAP-Request/Identity to mobile 00:24:d6:97:b3:be (EAP Id 1)
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.016: 00:24:d6:97:b3:be mscb->apfMsLwappLradNhMac = 00:00:0c:07:ac:dc mscb->apfMsLradSlotId = 1 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.016: 00:24:d6:97:b3:be  mscb->apfMsBssid = 18:33:9d:f0:21:80 mscb->apfMsAddress = 00:24:d6:97:b3:be mscb->apfMsApVapId = 2
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.016: 00:24:d6:97:b3:be  dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 220 mscb->apfMsLwappMwarInet.ipv4.addr = 176217288
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.016: 00:24:d6:97:b3:be  mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = 176325157 mscb->apfMsLwappLradPort = 9385
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.083: 00:24:d6:97:b3:be Received EAPOL EAPPKT from mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.083: 00:24:d6:97:b3:be Received Identity Response (count=1) from mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.083: 00:24:d6:97:b3:be Resetting reauth count 1 to 0 for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.083: 00:24:d6:97:b3:be EAP State update from Connecting to Authenticating for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.083: 00:24:d6:97:b3:be dot1x - moving mobile 00:24:d6:97:b3:be into Authenticating state
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.083: 00:24:d6:97:b3:be Entering Backend Auth Response state for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.086: 00:24:d6:97:b3:be Processing Access-Challenge for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.086: 00:24:d6:97:b3:be Entering Backend Auth Req state (id=214) for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.086: 00:24:d6:97:b3:be WARNING: updated EAP-Identifier 1 ===> 214 for STA 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.086: 00:24:d6:97:b3:be Sending EAP Request from AAA to mobile 00:24:d6:97:b3:be (EAP Id 214)
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.086: 00:24:d6:97:b3:be Allocating EAP Pkt for retransmission to mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.086: 00:24:d6:97:b3:be mscb->apfMsLwappLradNhMac = 00:00:0c:07:ac:dc mscb->apfMsLradSlotId = 1 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.086: 00:24:d6:97:b3:be  mscb->apfMsBssid = 18:33:9d:f0:21:80 mscb->apfMsAddress = 00:24:d6:97:b3:be mscb->apfMsApVapId = 2
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.086: 00:24:d6:97:b3:be  dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 220 mscb->apfMsLwappMwarInet.ipv4.addr = 176217288
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.086: 00:24:d6:97:b3:be  mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = 176325157 mscb->apfMsLwappLradPort = 9385
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.090: 00:24:d6:97:b3:be Received EAPOL EAPPKT from mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.090: 00:24:d6:97:b3:be Received EAP Response from mobile 00:24:d6:97:b3:be (EAP Id 214, EAP Type 13)
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.090: 00:24:d6:97:b3:be Resetting reauth count 0 to 0 for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.090: 00:24:d6:97:b3:be Entering Backend Auth Response state for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.091: 00:24:d6:97:b3:be Processing Access-Challenge for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.091: 00:24:d6:97:b3:be Entering Backend Auth Req state (id=215) for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.091: 00:24:d6:97:b3:be Sending EAP Request from AAA to mobile 00:24:d6:97:b3:be (EAP Id 215)
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.091: 00:24:d6:97:b3:be Reusing allocated memory for  EAP Pkt for retransmission to mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.091: 00:24:d6:97:b3:be mscb->apfMsLwappLradNhMac = 00:00:0c:07:ac:dc mscb->apfMsLradSlotId = 1 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.091: 00:24:d6:97:b3:be  mscb->apfMsBssid = 18:33:9d:f0:21:80 mscb->apfMsAddress = 00:24:d6:97:b3:be mscb->apfMsApVapId = 2
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.091: 00:24:d6:97:b3:be  dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 220 mscb->apfMsLwappMwarInet.ipv4.addr = 176217288
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.091: 00:24:d6:97:b3:be  mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = 176325157 mscb->apfMsLwappLradPort = 9385
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.095: 00:24:d6:97:b3:be Received EAPOL EAPPKT from mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.095: 00:24:d6:97:b3:be Received EAP Response from mobile 00:24:d6:97:b3:be (EAP Id 215, EAP Type 13)
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.095: 00:24:d6:97:b3:be Resetting reauth count 0 to 0 for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.095: 00:24:d6:97:b3:be Entering Backend Auth Response state for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.096: 00:24:d6:97:b3:be Processing Access-Challenge for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.096: 00:24:d6:97:b3:be Entering Backend Auth Req state (id=216) for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.096: 00:24:d6:97:b3:be Sending EAP Request from AAA to mobile 00:24:d6:97:b3:be (EAP Id 216)
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.096: 00:24:d6:97:b3:be Reusing allocated memory for  EAP Pkt for retransmission to mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.096: 00:24:d6:97:b3:be mscb->apfMsLwappLradNhMac = 00:00:0c:07:ac:dc mscb->apfMsLradSlotId = 1 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.096: 00:24:d6:97:b3:be  mscb->apfMsBssid = 18:33:9d:f0:21:80 mscb->apfMsAddress = 00:24:d6:97:b3:be mscb->apfMsApVapId = 2
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.096: 00:24:d6:97:b3:be  dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 220 mscb->apfMsLwappMwarInet.ipv4.addr = 176217288
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.096: 00:24:d6:97:b3:be  mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = 176325157 mscb->apfMsLwappLradPort = 9385
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.100: 00:24:d6:97:b3:be Received EAPOL EAPPKT from mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.100: 00:24:d6:97:b3:be Received EAP Response from mobile 00:24:d6:97:b3:be (EAP Id 216, EAP Type 13)
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.100: 00:24:d6:97:b3:be Resetting reauth count 0 to 0 for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.100: 00:24:d6:97:b3:be Entering Backend Auth Response state for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.101: 00:24:d6:97:b3:be Processing Access-Challenge for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.101: 00:24:d6:97:b3:be Entering Backend Auth Req state (id=217) for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.101: 00:24:d6:97:b3:be Sending EAP Request from AAA to mobile 00:24:d6:97:b3:be (EAP Id 217)
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.101: 00:24:d6:97:b3:be Reusing allocated memory for  EAP Pkt for retransmission to mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.101: 00:24:d6:97:b3:be mscb->apfMsLwappLradNhMac = 00:00:0c:07:ac:dc mscb->apfMsLradSlotId = 1 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.101: 00:24:d6:97:b3:be  mscb->apfMsBssid = 18:33:9d:f0:21:80 mscb->apfMsAddress = 00:24:d6:97:b3:be mscb->apfMsApVapId = 2
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.101: 00:24:d6:97:b3:be  dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 220 mscb->apfMsLwappMwarInet.ipv4.addr = 176217288
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.101: 00:24:d6:97:b3:be  mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = 176325157 mscb->apfMsLwappLradPort = 9385
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.105: 00:24:d6:97:b3:be Received EAPOL EAPPKT from mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.105: 00:24:d6:97:b3:be Received EAP Response from mobile 00:24:d6:97:b3:be (EAP Id 217, EAP Type 13)
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.105: 00:24:d6:97:b3:be Resetting reauth count 0 to 0 for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.105: 00:24:d6:97:b3:be Entering Backend Auth Response state for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.106: 00:24:d6:97:b3:be Processing Access-Challenge for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.106: 00:24:d6:97:b3:be Entering Backend Auth Req state (id=218) for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.106: 00:24:d6:97:b3:be Sending EAP Request from AAA to mobile 00:24:d6:97:b3:be (EAP Id 218)
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.106: 00:24:d6:97:b3:be Reusing allocated memory for  EAP Pkt for retransmission to mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.106: 00:24:d6:97:b3:be mscb->apfMsLwappLradNhMac = 00:00:0c:07:ac:dc mscb->apfMsLradSlotId = 1 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.106: 00:24:d6:97:b3:be  mscb->apfMsBssid = 18:33:9d:f0:21:80 mscb->apfMsAddress = 00:24:d6:97:b3:be mscb->apfMsApVapId = 2
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.106: 00:24:d6:97:b3:be  dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 220 mscb->apfMsLwappMwarInet.ipv4.addr = 176217288
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.106: 00:24:d6:97:b3:be  mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = 176325157 mscb->apfMsLwappLradPort = 9385
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.110: 00:24:d6:97:b3:be Received EAPOL EAPPKT from mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.110: 00:24:d6:97:b3:be Received EAP Response from mobile 00:24:d6:97:b3:be (EAP Id 218, EAP Type 13)
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.110: 00:24:d6:97:b3:be Resetting reauth count 0 to 0 for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.110: 00:24:d6:97:b3:be Entering Backend Auth Response state for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.111: 00:24:d6:97:b3:be Processing Access-Challenge for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.111: 00:24:d6:97:b3:be Entering Backend Auth Req state (id=219) for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.111: 00:24:d6:97:b3:be Sending EAP Request from AAA to mobile 00:24:d6:97:b3:be (EAP Id 219)
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.111: 00:24:d6:97:b3:be Reusing allocated memory for  EAP Pkt for retransmission to mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.111: 00:24:d6:97:b3:be mscb->apfMsLwappLradNhMac = 00:00:0c:07:ac:dc mscb->apfMsLradSlotId = 1 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.111: 00:24:d6:97:b3:be  mscb->apfMsBssid = 18:33:9d:f0:21:80 mscb->apfMsAddress = 00:24:d6:97:b3:be mscb->apfMsApVapId = 2
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.111: 00:24:d6:97:b3:be  dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 220 mscb->apfMsLwappMwarInet.ipv4.addr = 176217288
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.111: 00:24:d6:97:b3:be  mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = 176325157 mscb->apfMsLwappLradPort = 9385
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.115: 00:24:d6:97:b3:be Received EAPOL EAPPKT from mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.115: 00:24:d6:97:b3:be Received EAP Response from mobile 00:24:d6:97:b3:be (EAP Id 219, EAP Type 13)
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.115: 00:24:d6:97:b3:be Resetting reauth count 0 to 0 for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.115: 00:24:d6:97:b3:be Entering Backend Auth Response state for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.116: 00:24:d6:97:b3:be Processing Access-Challenge for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.116: 00:24:d6:97:b3:be Entering Backend Auth Req state (id=220) for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.116: 00:24:d6:97:b3:be Sending EAP Request from AAA to mobile 00:24:d6:97:b3:be (EAP Id 220)
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.116: 00:24:d6:97:b3:be Reusing allocated memory for  EAP Pkt for retransmission to mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.116: 00:24:d6:97:b3:be mscb->apfMsLwappLradNhMac = 00:00:0c:07:ac:dc mscb->apfMsLradSlotId = 1 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.116: 00:24:d6:97:b3:be  mscb->apfMsBssid = 18:33:9d:f0:21:80 mscb->apfMsAddress = 00:24:d6:97:b3:be mscb->apfMsApVapId = 2
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.116: 00:24:d6:97:b3:be  dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 220 mscb->apfMsLwappMwarInet.ipv4.addr = 176217288
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.116: 00:24:d6:97:b3:be  mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = 176325157 mscb->apfMsLwappLradPort = 9385
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.352: 00:24:d6:97:b3:be Received EAPOL EAPPKT from mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.352: 00:24:d6:97:b3:be Received EAP Response from mobile 00:24:d6:97:b3:be (EAP Id 220, EAP Type 13)
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.352: 00:24:d6:97:b3:be Resetting reauth count 0 to 0 for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.352: 00:24:d6:97:b3:be Entering Backend Auth Response state for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.354: 00:24:d6:97:b3:be Processing Access-Challenge for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.354: 00:24:d6:97:b3:be Entering Backend Auth Req state (id=221) for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.354: 00:24:d6:97:b3:be Sending EAP Request from AAA to mobile 00:24:d6:97:b3:be (EAP Id 221)
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.354: 00:24:d6:97:b3:be Reusing allocated memory for  EAP Pkt for retransmission to mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.354: 00:24:d6:97:b3:be mscb->apfMsLwappLradNhMac = 00:00:0c:07:ac:dc mscb->apfMsLradSlotId = 1 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.354: 00:24:d6:97:b3:be  mscb->apfMsBssid = 18:33:9d:f0:21:80 mscb->apfMsAddress = 00:24:d6:97:b3:be mscb->apfMsApVapId = 2
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.354: 00:24:d6:97:b3:be  dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 220 mscb->apfMsLwappMwarInet.ipv4.addr = 176217288
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.354: 00:24:d6:97:b3:be  mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = 176325157 mscb->apfMsLwappLradPort = 9385
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.359: 00:24:d6:97:b3:be Received EAPOL EAPPKT from mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.359: 00:24:d6:97:b3:be Received EAP Response from mobile 00:24:d6:97:b3:be (EAP Id 221, EAP Type 13)
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.359: 00:24:d6:97:b3:be Resetting reauth count 0 to 0 for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.359: 00:24:d6:97:b3:be Entering Backend Auth Response state for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.360: 00:24:d6:97:b3:be Processing Access-Challenge for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.360: 00:24:d6:97:b3:be Entering Backend Auth Req state (id=222) for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.360: 00:24:d6:97:b3:be Sending EAP Request from AAA to mobile 00:24:d6:97:b3:be (EAP Id 222)
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.360: 00:24:d6:97:b3:be Reusing allocated memory for  EAP Pkt for retransmission to mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.360: 00:24:d6:97:b3:be mscb->apfMsLwappLradNhMac = 00:00:0c:07:ac:dc mscb->apfMsLradSlotId = 1 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.360: 00:24:d6:97:b3:be  mscb->apfMsBssid = 18:33:9d:f0:21:80 mscb->apfMsAddress = 00:24:d6:97:b3:be mscb->apfMsApVapId = 2
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.360: 00:24:d6:97:b3:be  dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 220 mscb->apfMsLwappMwarInet.ipv4.addr = 176217288
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.360: 00:24:d6:97:b3:be  mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = 176325157 mscb->apfMsLwappLradPort = 9385
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.365: 00:24:d6:97:b3:be Received EAPOL EAPPKT from mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.365: 00:24:d6:97:b3:be Received EAP Response from mobile 00:24:d6:97:b3:be (EAP Id 222, EAP Type 13)
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.365: 00:24:d6:97:b3:be Resetting reauth count 0 to 0 for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.365: 00:24:d6:97:b3:be Entering Backend Auth Response state for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.366: 00:24:d6:97:b3:be Processing Access-Challenge for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.366: 00:24:d6:97:b3:be Entering Backend Auth Req state (id=223) for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.366: 00:24:d6:97:b3:be Sending EAP Request from AAA to mobile 00:24:d6:97:b3:be (EAP Id 223)
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.366: 00:24:d6:97:b3:be Reusing allocated memory for  EAP Pkt for retransmission to mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.366: 00:24:d6:97:b3:be mscb->apfMsLwappLradNhMac = 00:00:0c:07:ac:dc mscb->apfMsLradSlotId = 1 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.366: 00:24:d6:97:b3:be  mscb->apfMsBssid = 18:33:9d:f0:21:80 mscb->apfMsAddress = 00:24:d6:97:b3:be mscb->apfMsApVapId = 2
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.366: 00:24:d6:97:b3:be  dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 220 mscb->apfMsLwappMwarInet.ipv4.addr = 176217288
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.366: 00:24:d6:97:b3:be  mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = 176325157 mscb->apfMsLwappLradPort = 9385
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.371: 00:24:d6:97:b3:be Received EAPOL EAPPKT from mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.371: 00:24:d6:97:b3:be Received EAP Response from mobile 00:24:d6:97:b3:be (EAP Id 223, EAP Type 13)
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.371: 00:24:d6:97:b3:be Resetting reauth count 0 to 0 for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.371: 00:24:d6:97:b3:be Entering Backend Auth Response state for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.372: 00:24:d6:97:b3:be Processing Access-Challenge for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.372: 00:24:d6:97:b3:be Entering Backend Auth Req state (id=224) for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.372: 00:24:d6:97:b3:be Sending EAP Request from AAA to mobile 00:24:d6:97:b3:be (EAP Id 224)
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.372: 00:24:d6:97:b3:be Reusing allocated memory for  EAP Pkt for retransmission to mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.372: 00:24:d6:97:b3:be mscb->apfMsLwappLradNhMac = 00:00:0c:07:ac:dc mscb->apfMsLradSlotId = 1 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.372: 00:24:d6:97:b3:be  mscb->apfMsBssid = 18:33:9d:f0:21:80 mscb->apfMsAddress = 00:24:d6:97:b3:be mscb->apfMsApVapId = 2
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.372: 00:24:d6:97:b3:be  dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 220 mscb->apfMsLwappMwarInet.ipv4.addr = 176217288
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.372: 00:24:d6:97:b3:be  mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = 176325157 mscb->apfMsLwappLradPort = 9385
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.375: 00:24:d6:97:b3:be Received EAPOL EAPPKT from mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.375: 00:24:d6:97:b3:be Received EAP Response from mobile 00:24:d6:97:b3:be (EAP Id 224, EAP Type 13)
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.375: 00:24:d6:97:b3:be Resetting reauth count 0 to 0 for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.375: 00:24:d6:97:b3:be Entering Backend Auth Response state for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.389: 00:24:d6:97:b3:be Processing Access-Challenge for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.389: 00:24:d6:97:b3:be Entering Backend Auth Req state (id=225) for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.389: 00:24:d6:97:b3:be Sending EAP Request from AAA to mobile 00:24:d6:97:b3:be (EAP Id 225)
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.389: 00:24:d6:97:b3:be Reusing allocated memory for  EAP Pkt for retransmission to mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.389: 00:24:d6:97:b3:be mscb->apfMsLwappLradNhMac = 00:00:0c:07:ac:dc mscb->apfMsLradSlotId = 1 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.389: 00:24:d6:97:b3:be  mscb->apfMsBssid = 18:33:9d:f0:21:80 mscb->apfMsAddress = 00:24:d6:97:b3:be mscb->apfMsApVapId = 2
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.389: 00:24:d6:97:b3:be  dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 220 mscb->apfMsLwappMwarInet.ipv4.addr = 176217288
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.389: 00:24:d6:97:b3:be  mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = 176325157 mscb->apfMsLwappLradPort = 9385
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.391: 00:24:d6:97:b3:be Received EAPOL EAPPKT from mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.391: 00:24:d6:97:b3:be Received EAP Response from mobile 00:24:d6:97:b3:be (EAP Id 225, EAP Type 13)
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.391: 00:24:d6:97:b3:be Resetting reauth count 0 to 0 for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.391: 00:24:d6:97:b3:be Entering Backend Auth Response state for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Processing Access-Accept for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Resetting web IPv4 acl from 255 to 255
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Resetting web IPv4 Flex acl from 65535 to 65535
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Username entry ([email protected]) created for mobile, length = 253 
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Username entry ([email protected]) created in mscb for mobile, length = 253 
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be override for default ap group, marking intgrp NULL
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Applying Interface policy on Mobile, role Unassociated. Ms NAC State 2 Quarantine Vlan 0 Access Vlan 220
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Re-applying interface policy for client 
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be 0.0.0.0 8021X_REQD (3) Changing IPv4 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2219)
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be 0.0.0.0 8021X_REQD (3) Changing IPv6 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2240)
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be apfApplyWlanPolicy: Retaining the ACL recieved in AAA attributes 1 on mobile 
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be apfApplyWlanPolicy: Apply WLAN Policy over PMIPv6 Client Mobility Type
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Inserting AAA Override struct for mobile
        MAC: 00:24:d6:97:b3:be, source 4
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Setting re-auth timeout to 1800 seconds, got from WLAN config.
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Station 00:24:d6:97:b3:be setting dot1x reauth timeout = 1800
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Creating a PKC PMKID Cache entry for station 00:24:d6:97:b3:be (RSN 2)
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Resetting MSCB PMK Cache Entry 0 for station 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Setting active key cache index 8 ---> 8
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Setting active key cache index 8 ---> 0
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Adding BSSID 18:33:9d:f0:21:8e to PMKID cache at index 0 for station 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: New PMKID: (16)
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410:      [0000] 6f d1 ce 84 08 74 41 a5 06 6b 89 02 c9 e9 f8 c8
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Disabling re-auth since PMK lifetime can take care of same.
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be unsetting PmkIdValidatedByAp
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Client in Posture Reqd state. PMK cache not updated.
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Sending EAP-Success to mobile 00:24:d6:97:b3:be (EAP Id 225)
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be mscb->apfMsLwappLradNhMac = 00:00:0c:07:ac:dc mscb->apfMsLradSlotId = 1 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be  mscb->apfMsBssid = 18:33:9d:f0:21:80 mscb->apfMsAddress = 00:24:d6:97:b3:be mscb->apfMsApVapId = 2
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be  dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 220 mscb->apfMsLwappMwarInet.ipv4.addr = 176217288
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be  mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = 176325157 mscb->apfMsLwappLradPort = 9385
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Freeing AAACB from Dot1xCB as AAA auth is done for  mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be EAPOL Header: 
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00000000: 02 03 5f 00                                       .._.
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Found an cache entry for BSSID 18:33:9d:f0:21:8e in PMKID cache at index 0 of station 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Found an cache entry for BSSID 18:33:9d:f0:21:8e in PMKID cache at index 0 of station 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: Including PMKID in M1  (16)
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410:      [0000] 6f d1 ce 84 08 74 41 a5 06 6b 89 02 c9 e9 f8 c8
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Starting key exchange to mobile 00:24:d6:97:b3:be, data packets will be dropped
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Sending EAPOL-Key Message to mobile 00:24:d6:97:b3:be
       state INITPMK (message 1), replay counter 00.00.00.00.00.00.00.00
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Sending EAPOL-Key Message to mobile 00:24:d6:97:b3:be
       state INITPMK (message 1), replay counter 00.00.00.00.00.00.00.00
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Reusing allocated memory for  EAP Pkt for retransmission to mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be mscb->apfMsLwappLradNhMac = 00:00:0c:07:ac:dc mscb->apfMsLradSlotId = 1 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be  mscb->apfMsBssid = 18:33:9d:f0:21:80 mscb->apfMsAddress = 00:24:d6:97:b3:be mscb->apfMsApVapId = 2
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be  dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 220 mscb->apfMsLwappMwarInet.ipv4.addr = 176217288
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be  mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = 176325157 mscb->apfMsLwappLradPort = 9385
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Entering Backend Auth Success state (id=225) for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Received Auth Success while in Authenticating state for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be dot1x - moving mobile 00:24:d6:97:b3:be into Authenticated state
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.414: 00:24:d6:97:b3:be Received EAPOL-Key from mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.414: 00:24:d6:97:b3:be Received EAPOL-key in PTK_START state (message 2) from mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.414: 00:24:d6:97:b3:be PMK: Sending cache add
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.414: 00:24:d6:97:b3:be Stopping retransmission timer for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.414: 00:24:d6:97:b3:be EAPOL Header: 
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.414: 00000000: 02 03 5f 00                                       .._.
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.414: 00:24:d6:97:b3:be Sending EAPOL-Key Message to mobile 00:24:d6:97:b3:be
       state PTKINITNEGOTIATING (message 3), replay counter 00.00.00.00.00.00.00.01
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.414: 00:24:d6:97:b3:be Sending EAPOL-Key Message to mobile 00:24:d6:97:b3:be
       state PTKINITNEGOTIATING (message 3), replay counter 00.00.00.00.00.00.00.01
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.414: 00:24:d6:97:b3:be Reusing allocated memory for  EAP Pkt for retransmission to mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.414: 00:24:d6:97:b3:be mscb->apfMsLwappLradNhMac = 00:00:0c:07:ac:dc mscb->apfMsLradSlotId = 1 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.414: 00:24:d6:97:b3:be  mscb->apfMsBssid = 18:33:9d:f0:21:80 mscb->apfMsAddress = 00:24:d6:97:b3:be mscb->apfMsApVapId = 2
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.414: 00:24:d6:97:b3:be  dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 220 mscb->apfMsLwappMwarInet.ipv4.addr = 176217288
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.414: 00:24:d6:97:b3:be  mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = 176325157 mscb->apfMsLwappLradPort = 9385
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be Received EAPOL-Key from mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be Received EAPOL-key in PTKINITNEGOTIATING state (message 4) from mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be Stopping retransmission timer for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be Freeing EAP Retransmit Bufer for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be apfMs1xStateInc
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be 0.0.0.0 8021X_REQD (3) Change state to L2AUTHCOMPLETE (4) last state 8021X_REQD (3)
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be Central switch is FALSE
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be Sending the Central Auth Info
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be Central Auth Info Allocated PMKLen = 32
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: EapolReplayCounter: 00 00 00 00 00 00 00 01
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: EapolReplayCounter: 00 00 00 00 00 00 00 01
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be PMK: pmkActiveIndex = 0
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be EapolReplayCounter: 00 00 00 00 00 00 00 01
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be msAssocTypeFlagsMsb = 0 msAssocTypeFlagsLsb = 2
    apfMsEntryType = 0 apfMsEapType = 13
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be 0.0.0.0 L2AUTHCOMPLETE (4) DHCP required on AP 18:33:9d:f0:21:80 vapId 2 apVapId 2for this client
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be Not Using WMM Compliance code qosCap 00
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be 0.0.0.0 L2AUTHCOMPLETE (4) Plumbed mobile LWAPP rule on AP 18:33:9d:f0:21:80 vapId 2 apVapId 2 flex-acl-name:POSTURE_REDIRECT_ACL 
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be 0.0.0.0 L2AUTHCOMPLETE (4) Change state to DHCP_REQD (7) last state L2AUTHCOMPLETE (4)
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be 0.0.0.0 DHCP_REQD (7) pemAdvanceState2 6166, Adding TMP rule
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be 0.0.0.0 DHCP_REQD (7) Adding Fast Path rule
      type = Airespace AP - Learn IP address
      on AP 18:33:9d:f0:21:80, slot 1, interface = 1, QOS = 0
      IPv4 ACL ID = 255, IPv
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be 0.0.0.0 DHCP_REQD (7) Fast Path rule (contd...) 802.1P = 0, DSCP = 0, TokenID = 64206  Local Bridging Vlan = 220, Local Bridging intf id = 0
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be 0.0.0.0 DHCP_REQD (7) Successfully plumbed mobile rule (IPv4 ACL ID 255, IPv6 ACL ID 255, L2 ACL ID 255)
    *apfReceiveTask: Aug 12 10:58:24.418: 00:24:d6:97:b3:be 0.0.0.0 DHCP_REQD (7) State Update from Mobility-Incomplete to Mobility-Complete, mobility role=Local, client state=APF_MS_STATE_ASSOCIATED
    *apfReceiveTask: Aug 12 10:58:24.418: 00:24:d6:97:b3:be 0.0.0.0 DHCP_REQD (7) pemAdvanceState2 5761, Adding TMP rule
    *apfReceiveTask: Aug 12 10:58:24.418: 00:24:d6:97:b3:be 0.0.0.0 DHCP_REQD (7) Replacing Fast Path rule
      type = Airespace AP - Learn IP address
      on AP 18:33:9d:f0:21:80, slot 1, interface = 1, QOS = 0
      IPv4 ACL ID = 255, 
    *apfReceiveTask: Aug 12 10:58:24.418: 00:24:d6:97:b3:be 0.0.0.0 DHCP_REQD (7) Fast Path rule (contd...) 802.1P = 0, DSCP = 0, TokenID = 64206  Local Bridging Vlan = 220, Local Bridging intf id = 0
    *apfReceiveTask: Aug 12 10:58:24.418: 00:24:d6:97:b3:be 0.0.0.0 DHCP_REQD (7) Successfully plumbed mobile rule (IPv4 ACL ID 255, IPv6 ACL ID 255, L2 ACL ID 255)
    *pemReceiveTask: Aug 12 10:58:24.418: 00:24:d6:97:b3:be 0.0.0.0 Added NPU entry of type 9, dtlFlags 0x0
    *pemReceiveTask: Aug 12 10:58:24.418: 00:24:d6:97:b3:be 0.0.0.0 Added NPU entry of type 9, dtlFlags 0x0
    *spamApTask6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be spamEncodeCentralAuthInoMsPayload: msAssocTypeFlagsMsb = 0 msAssocTypeFlagsLsb = 2
    apfMsEntryType = 0 pmkLen = 32
    *DHCP Socket Task: Aug 12 10:58:24.546: 00:24:d6:97:b3:be DHCP received op BOOTREPLY (2) (len 325,vlan 220, port 1, encap 0xec03)
    *DHCP Socket Task: Aug 12 10:58:24.546: 00:24:d6:97:b3:be DHCP setting server from ACK (server 10.0.17.85, yiaddr 10.130.130.120)
    *DHCP Socket Task: Aug 12 10:58:24.548: 00:24:d6:97:b3:be 10.130.130.120 DHCP_REQD (7) Change state to WEBAUTH_REQD (8) last state DHCP_REQD (7)
    *DHCP Socket Task: Aug 12 10:58:24.548: 00:24:d6:97:b3:be 10.130.130.120 WEBAUTH_REQD (8) pemAdvanceState2 6671, Adding TMP rule
    *DHCP Socket Task: Aug 12 10:58:24.548: 00:24:d6:97:b3:be 10.130.130.120 WEBAUTH_REQD (8) Replacing Fast Path rule
      type = Airespace AP Client - ACL passthru
      on AP 18:33:9d:f0:21:80, slot 1, interface = 1, QOS = 0
      IPv4 A
    *DHCP Socket Task: Aug 12 10:58:24.548: 00:24:d6:97:b3:be 10.130.130.120 WEBAUTH_REQD (8) Fast Path rule (contd...) 802.1P = 0, DSCP = 0, TokenID = 64206  Local Bridging Vlan = 220, Local Bridging intf id = 0
    *DHCP Socket Task: Aug 12 10:58:24.548: 00:24:d6:97:b3:be 10.130.130.120 WEBAUTH_REQD (8) Successfully plumbed mobile rule (IPv4 ACL ID 1, IPv6 ACL ID 255, L2 ACL ID 255)
    *DHCP Socket Task: Aug 12 10:58:24.548: 00:24:d6:97:b3:be Plumbing web-auth redirect rule due to user logout
    *DHCP Socket Task: Aug 12 10:58:24.548: 00:24:d6:97:b3:be Assigning Address 10.130.130.120 to mobile 
    *DHCP Socket Task: Aug 12 10:58:24.548: 00:24:d6:97:b3:be DHCP success event for client. Clearing dhcp failure count for interface management.
    *DHCP Socket Task: Aug 12 10:58:24.548: 00:24:d6:97:b3:be DHCP success event for client. Clearing dhcp failure count for interface management.
    *pemReceiveTask: Aug 12 10:58:24.548: 00:24:d6:97:b3:be 10.130.130.120 Added NPU entry of type 2, dtlFlags 0x0
    *IPv6_Msg_Task: Aug 12 10:58:25.330: 00:24:d6:97:b3:be Pushing IPv6 Vlan Intf ID 0: fe80:0000:0000:0000:f524:1910:69f0:9482 , and MAC: 00:24:D6:97:B3:BE , Binding to Data Plane. SUCCESS !! dhcpv6bitmap 0
    *IPv6_Msg_Task: Aug 12 10:58:25.330: 00:24:d6:97:b3:be Link Local address fe80::f524:1910:69f0:9482 updated to mscb. Not Advancing pem state.Current state: mscb in apfMsMmInitial mobility state and client state APF_MS_STATE_A
    *DHCP Socket Task: Aug 12 10:58:28.581: 00:24:d6:97:b3:be DHCP received op BOOTREPLY (2) (len 308,vlan 220, port 1, encap 0xec03)
    *DHCP Socket Task: Aug 12 10:58:28.589: 00:24:d6:97:b3:be DHCP received op BOOTREPLY (2) (len 308,vlan 220, port 1, encap 0xec03)
    *DHCP Socket Task: Aug 12 11:00:07.959: 00:24:d6:97:b3:be DHCP received op BOOTREPLY (2) (len 308,vlan 220, port 1, encap 0xec03)
    *DHCP Socket Task: Aug 12 11:00:07.967: 00:24:d6:97:b3:be DHCP received op BOOTREPLY (2) (len 308,vlan 220, port 1, encap 0xec03)
    *DHCP Socket Task: Aug 12 11:01:59.153: 00:24:d6:97:b3:be DHCP received op BOOTREPLY (2) (len 308,vlan 220, port 1, encap 0xec03)
    Can you see any obvious reason why the NAC agent wont pop up?
    Thanks
    Mario

  • WLC 5508 - EAP-TLS - Windows 8.1 Third Party PKI

    Hello,
    Does anybody know what could prevent a Windows 8/8.1 system to connect to a WLC via EAP-TLS? Windows 7/XP do not have any problems here.The radius server accepts the request, but WIndows 8 still tries to authenticate.
    Software is updated to 7.6.120.0, I tried to setup timeout values, but no success at all.
    Did anyone have similar problems with Windows 8/81?
    *Dot1x_NW_MsgTask_7: Jun 24 12:43:10.604: 0c:8b:fd:eb:16:17 Starting key exchange to mobile 0c:8b:fd:eb:16:17, data packets will be dropped
    *Dot1x_NW_MsgTask_7: Jun 24 12:43:10.604: 0c:8b:fd:eb:16:17 Sending EAPOL-Key Message to mobile 0c:8b:fd:eb:16:17
       state INITPMK (message 1), replay counter 00.00.00.00.00.00.00.00
    *Dot1x_NW_MsgTask_7: Jun 24 12:43:10.604: 0c:8b:fd:eb:16:17 Sending EAPOL-Key Message to mobile 0c:8b:fd:eb:16:17
       state INITPMK (message 1), replay counter 00.00.00.00.00.00.00.00
    *Dot1x_NW_MsgTask_7: Jun 24 12:43:10.604: 0c:8b:fd:eb:16:17 Reusing allocated memory for  EAP Pkt for retransmission to mobile 0c:8b:fd:eb:16:17
    *Dot1x_NW_MsgTask_7: Jun 24 12:43:10.604: 0c:8b:fd:eb:16:17 mscb->apfMsLwappLradNhMac = 00:24:97:52:87:d6 mscb->apfMsLradSlotId = 0 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 13
    *Dot1x_NW_MsgTask_7: Jun 24 12:43:10.604: 0c:8b:fd:eb:16:17  mscb->apfMsBssid = 00:24:97:70:9a:00 mscb->apfMsAddress = 0c:8b:fd:eb:16:17 mscb->apfMsApVapId = 1
    *Dot1x_NW_MsgTask_7: Jun 24 12:43:10.604: 0c:8b:fd:eb:16:17  dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId =
    0 mscb->apfMsLwappMwarInet.ipv4.addr = -1407817979
    *Dot1x_NW_MsgTask_7: Jun 24 12:43:10.604: 0c:8b:fd:eb:16:17  mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = -1407817773 mscb->apfMsLwappLradPort = 10367
    *Dot1x_NW_MsgTask_7: Jun 24 12:43:10.604: 0c:8b:fd:eb:16:17 Entering Backend Auth Success state (id=6) for mobile 0c:8b:fd:eb:16:17
    *Dot1x_NW_MsgTask_7: Jun 24 12:43:10.604: 0c:8b:fd:eb:16:17 Received Auth Success while in Authenticating state for mobile 0c:8b:fd:eb:16:17
    *Dot1x_NW_MsgTask_7: Jun 24 12:43:10.604: 0c:8b:fd:eb:16:17 dot1x - moving mobile 0c:8b:fd:eb:16:17 into Authenticated state
    *osapiBsnTimer: Jun 24 12:43:13.801: 0c:8b:fd:eb:16:17 802.1x 'timeoutEvt' Timer expired for station 0c:8b:fd:eb:16:17 and for message = M2
    *dot1xMsgTask: Jun 24 12:43:13.801: 0c:8b:fd:eb:16:17 Retransmit 1 of EAPOL-Key M1 (length 121) for mobile 0c:8b:fd:eb:16:17
    *dot1xMsgTask: Jun 24 12:43:13.802: 0c:8b:fd:eb:16:17 mscb->apfMsLwappLradNhMac = 00:24:97:52:87:d6 mscb->apfMsLradSlotId = 0 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 13
    *dot1xMsgTask: Jun 24 12:43:13.802: 0c:8b:fd:eb:16:17  mscb->apfMsBssid = 00:24:97:70:9a:00 mscb->apfMsAddress = 0c:8b:fd:eb:16:17 mscb->apfMsApVapId = 1
    *dot1xMsgTask: Jun 24 12:43:13.802: 0c:8b:fd:eb:16:17  dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 0 mscb->apfMsLwappMwarInet.ipv4.addr = -1407817979
    *dot1xMsgTask: Jun 24 12:43:13.802: 0c:8b:fd:eb:16:17  mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = -1407817773 mscb->apfMsLwappLradPort = 10367
    *osapiBsnTimer: Jun 24 12:43:16.801: 0c:8b:fd:eb:16:17 802.1x 'timeoutEvt' Timer expired for station 0c:8b:fd:eb:16:17 and for message = M2
    *dot1xMsgTask: Jun 24 12:43:16.802: 0c:8b:fd:eb:16:17 Retransmit 2 of EAPOL-Key M1 (length 121) for mobile 0c:8b:fd:eb:16:17
    *dot1xMsgTask: Jun 24 12:43:16.802: 0c:8b:fd:eb:16:17 mscb->apfMsLwappLradNhMac = 00:24:97:52:87:d6 mscb->apfMsLradSlotId = 0 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 13
    *dot1xMsgTask: Jun 24 12:43:16.802: 0c:8b:fd:eb:16:17  mscb->apfMsBssid = 00:24:97:70:9a:00 mscb->apfMsAddress = 0c:8b:fd:eb:16:17 mscb->apfMsApVapId = 1
    *dot1xMsgTask: Jun 24 12:43:16.802: 0c:8b:fd:eb:16:17  dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 0 mscb->apfMsLwappMwarInet.ipv4.addr = -1407817979
    *dot1xMsgTask: Jun 24 12:43:16.802: 0c:8b:fd:eb:16:17  mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = -1407817773 mscb->apfMsLwappLradPort = 10367
    *osapiBsnTimer: Jun 24 12:43:19.801: 0c:8b:fd:eb:16:17 802.1x 'timeoutEvt' Timer expired for station 0c:8b:fd:eb:16:17 and for message = M2
    *dot1xMsgTask: Jun 24 12:43:19.801: 0c:8b:fd:eb:16:17 Retransmit failure for EAPOL-Key M1 to mobile 0c:8b:fd:eb:16:17, retransmit count 3, mscb deauth count 0
    Any hint would be great .... Thank you...

    Hello Dino,
      thanks very much for your reply.
      The client uses a machine-certificate, the PKI is not a microsoft one, but a third party PKI.   The certificate is fresh and valid, the root-cert is installed and checked to be validated against it for the login.
    Clock is correct too. The same setup works flawlessly in Windows 7 and XP.
    EKU is set on the certificate (1.3.6.1.5.5.7.3.2)
    I suspect the cert-setup itself, but don't get a clue where this might stuck...
    Björn

Maybe you are looking for