WLC is ARPing but will not receive answer from vlan-switch

Hi - this is my first posting in theese forums - hope I get it right
Setup: a procurve-vlan-switch (2915) is connected directly to a cisco-wlc (2504) on two ports.
     Port 1 on the wlc has the management- and apmanager-interface, untagged, connected to untagged port on procurveswitch.
     Port 2 on the wlc has a dynamic interface (vlan 100) connected to tagged (vlan100) port on the switch.
Port 1 I can ping, and everything works as it should, LAP connects and so on.
Port 2 I can't ping, and it will not let clients get an ip-address i the vlan100 segment.
     Wireshark tells me, that wlc sends arp-requests to the vlan-gateway on the procurve switch, and also that the switch replies in the same vlan (with tagged packets). But the WLC will not pick theese answers up and keeps ARPing for the gateway. Result is = no dhcp-answer to the clients.
Workaround: If I first ping from the wlc to the gateway, everything works for 5 minutes, i.e. I can ping the dynamic interface on the wlc and clients get ip-addresses, but when the arp-cache times out, everything goes black again.
BIG question: Can anyone help me with this? Why will the wlc not pick the arp-answer from the switch? The wlc asks with tagged packets and get tagged replies imediatly but will not listen
Sincerely
Nicholas Wolf Haamann

Is there a reason you are using two separate ports on the WLC?
Generally you would just create a Trunk port to the WLC and all traffic would pass over it.
The fact it works for 5 minutes makes me wonder if the WLC is somehow using the same MAC for both ports. What MAC addresses does the MAC address table on the HP switch show for both ports?

Similar Messages

  • My Ipad will not receive signal from new home Xfinity modem.  I reset Pad but still doesnt work.

    My Ipad will not receive signal from new home Xfinity modem.  I reset Pad but still doen't get WIFI

    Does it not show the presence of a wifi signal, or just not connect?
    Some things to try first:
    1. Turn Off your iPad. Then turn Off (disconnect power cord for 30 seconds or longer) the wireless router & then back On. Now boot your iPad. Hopefully it will see the WiFi.
    2. Go to Settings>Wi-Fi and turn Off. Then while at Settings>Wi-Fi, turn back On and chose a Network.
    3. Change the channel on your wireless router (Auto or Channel 6 is best). Instructions at http://macintoshhowto.com/advanced/how-to-get-a-good-range-on-your-wireless-netw ork.html
    4. Go into your router security settings and change from WEP to WPA with AES.
    5.  Renew IP Address: (especially if you are droping internet connection)
        •    Launch Settings app
        •    Tap on Wi-Fi
        •    Tap on the blue arrow of the Wi-Fi network that you connect to from the list
        •    In the window that opens, tap on the Renew Lease button
    6. Potential Quick Fixes When Your iPad Won’t Connect to Your Wifi Network
    http://ipadinsight.com/ipad-tips-tricks/potential-quick-fixes-when-your-ipad-won t-connect-to-your-wifi-network/
    ~~~~~~~~~~~~~~~~~~~~~~~~~
    Wi-Fi Fix for iOS 6
    https://discussions.apple.com/thread/4823738?tstart=240
    iOS 6 Wifi Problems/Fixes
    How To: Workaround iPad Wi-Fi Issues
    http://www.theipadfan.com/workaround-ipad-wifi-issues/
    Another Fix For iOS 6 WiFi Problems
    http://tabletcrunch.com/2012/10/27/fix-ios-6-wifi-problems-ssid/
    Wifi Doesn't Connect After Waking From Sleep - Sometimes increasing screen brightness prevents the failure to reconnect after waking from sleep. According to Apple, “If brightness is at lowest level, increase it by moving the slider to the right and set auto brightness to off.”
    Fix For iOS 6 WiFi Problems?
    http://tabletcrunch.com/2012/09/27/fix-ios-6-wifi-problems/
    Did iOS 6 Screw Your Wi-Fi? Here’s How to Fix It
    http://gizmodo.com/5944761/does-ios-6-have-a-wi+fi-bug
    How To Fix Wi-Fi Connectivity Issue After Upgrading To iOS 6
    http://www.iphonehacks.com/2012/09/fix-wi-fi-connectivity-issue-after-upgrading- to-ios-6.html
    iOS 6 iPad 3 wi-fi "connection fix" for netgear router
    http://www.youtube.com/watch?v=XsWS4ha-dn0
    Apple's iOS 6 Wi-Fi problems
    http://www.zdnet.com/apples-ios-6-wi-fi-problems-linger-on-7000004799/
    ~~~~~~~~~~~~~~~~~~~~~~~
    How to Boost Your Wi-Fi Signal
    http://ipad.about.com/od/iPad_Troubleshooting/a/How-To-Boost-Your-Wi-Fi-Signal.h tm
    Troubleshooting a Weak Wi-Fi Signal
    http://ipad.about.com/od/iPad_Troubleshooting/a/Troubleshooting-A-Weak-Wi-Fi-Sig nal.htm
    How to Fix a Poor Wi-Fi Signal on Your iPad
    http://ipad.about.com/od/iPad_Troubleshooting/a/How-To-Fix-A-Poor-Wi-Fi-Signal-O n-Your-iPad.htm
    iOS Troubleshooting Wi-Fi networks and connections  http://support.apple.com/kb/TS1398
    iPad: Issues connecting to Wi-Fi networks  http://support.apple.com/kb/ts3304
    WiFi Connecting/Troubleshooting http://www.apple.com/support/ipad/wifi/
    How to Fix: My iPad Won't Connect to WiFi
    http://ipad.about.com/od/iPad_Troubleshooting/ss/How-To-Fix-My-Ipad-Wont-Connect -To-Wi-Fi.htm
    iOS: Connecting to the Internet http://support.apple.com/kb/HT1695
    iOS: Recommended settings for Wi-Fi routers and access points  http://support.apple.com/kb/HT4199
    How to Quickly Fix iPad 3 Wi-Fi Reception Problems
    http://osxdaily.com/2012/03/21/fix-new-ipad-3-wi-fi-reception-problems/
    iPad Wi-Fi Problems: Comprehensive List of Fixes
    http://appletoolbox.com/2010/04/ipad-wi-fi-problems-comprehensive-list-of-fixes/
    Connect iPad to Wi-Fi (with troubleshooting info)
    http://thehowto.wikidot.com/wifi-connect-ipad
    Fix iPad Wifi Connection and Signal Issues  http://www.youtube.com/watch?v=uwWtIG5jUxE
    Fix Slow WiFi Issue https://discussions.apple.com/thread/2398063?start=60&tstart=0
    How To Fix iPhone, iPad, iPod Touch Wi-Fi Connectivity Issue http://tinyurl.com/7nvxbmz
    Unable to Connect After iOS Update - saw this solution on another post.
    https://discussions.apple.com/thread/4010130
    Note - When troubleshooting wifi connection problems, don't hold your iPad by hand. There have been a few reports that holding the iPad by hand, seems to attenuate the wifi signal.
    Wi-Fi or Bluetooth settings grayed out or dim
    http://support.apple.com/kb/TS1559
    ~~~~~~~~~~~~~~~
    If any of the above solutions work, please post back what solved your problem. It will help others with the same problem.
     Cheers, Tom

  • Calendar schedule blank. All appts disappeared from 3g iphone calendar synced to yahoo. After Yahoo corrected error message on their website and I re-synced my iphone, calendar reappears but will not allow edit from iphone. I can't find settings to change

    Calendar schedule blank. All appts disappeared from 3g iphone calendar synced to yahoo. After Yahoo corrected error message on their website and I re-synced my iphone, calendar reappears but will not allow edit from iphone. I can't find settings within Yahoo or within my iphone to alter editing options.
    How can I get access to edit and delete the Yahoo calendar from my iphone? I never schedule anything from the Yahoo webpage. All my appointments and reminders are scheduled from the iphone.
    iOS 4.2.1 (8C148a)

    My Yahoo email account worked just fine on my iPhone 4S  for the last 2 months. Then this morning I started receiving the apple.imap.mail,yahoo error.  I tried all of the steps above in solving the yahoo email issue including numerous hard re-sets and deletions of my yahoo account settings without any success. So I gave up trying to use the default Yahoo setup option.  I added my Yahoo account back as an "other" type email account and then had the option to choose to set it up as a "POP" account instead of an IMAP type. I then just used the server settings recommended from Yahoo Help for a Yahoo Plus Email POP (or just google yahoo plus email pop settings). This works and I am back in business.
    I'm not sure if this will work for yahoo mail classic accounts.
    Frustrating that this issue seems to have been going on for quite awhile and Apple still as not made any acknowledgement of this issue or proposed a fix for those of us that can not resolve the issue with a reset.

  • TS4002 Hello, icloud receive messages from gilly hicks, but does not receive messages from another personal account... this is happening me since one week and i dont know how to solve this.... error in the mail delivery system says not valid IPv4 SMTP err

    Hello, icloud receive messages from gilly hicks, but does not receive messages from another personal account... this is happening me since one week and i dont know how to solve this.... error in the mail delivery system says not valid IPv4
    SMTP error from remote mail server after RCPT TO:<[email protected]>:
       host mx6.me.com.akadns.net [17.158.8.114]: 550 5.7.0 Blocked - see https://support.proofpoint.com/dnsbl-lookup.cgi?ip=184.173.9.56:
       [email protected]
    i do alse receive from gmail....
    please help... what is happening!!!!

    Just to recap, this is a collection of ports I have collected over time for people who needed this information when setting up the HP ePrint app so that they could view their email from within the app.  I am certain other applications also need this information.  Although lengthy, I could not find a more comprehensive place to retrieve this information.  Feel free to post additional information, faulty information, or other related topics below as this is simply a collection of data and it would be practically impossible to test all of them. Thank you!
    Don't forgot to say thanks by giving "Kudos" if I helped solve your problem.
    When a solution is found please mark the post that solves your issue.
    Every problem has a solution!

  • Have just loaded Safari 5.1.  4 times.  It presents a blank page but will not load anything from the web.

    Have just loaded Safari 5.1.  4 times.  It presents a blank page but will not load anything from the web.   What do I have to do to get it to work.   It worked fine until the update was offered.

    Funny thing, even this page was loaded and then quickly turned blank for me (I'm writing from Chrome).
    Hope they fix it soon!

  • My IPod nano 6 connects to my library but will not receive new music and playlists

    My ipod 6th generation will not receive new songs and playlists from my library on my PC. My ipod shows up in the itunes library when I connect it. It syncs when it is plugged in to computer but the sync is very short. I changed to a new computer back in September 2013. My old one crashed.  I have synced my ipad 2 and my iPhone 4S to itunes library on the new computer.  All these devices show up in the "manage my devices" list except my ipod 6th generation. There is no "add device" to this itunes account, only an option to deauthorize the computer, the iPhone or the ipad.
    The ipod downloaded songs that I added to my computer library on my new computer, but will not add new purchased songs nor library playlists.
    My computer is shared with my husband. His user account on the same computer shows up in my "manage devices" section of my itunes account. He doesn't use it. I thought I had to add my itunes on his part of the computer because his is the "main user". 
    I'm not sure what to do.  Should I take my computer, iPhone, ipad and nano to an appointment at the Genius Bar at the Apple Store?  Any help is appreciated. Thank you.

    I kept working at this after posting. On the sync page for the ipod on itunes library I chose to remove the iPods association with my old computer. It erased all the old content from the old computer and then put all my checked songs from the new computer on my iPod nano.

  • 3702i AP's not Joining WLC - Layer 3 discovery request not received on management VLAN

    Hi Guys, 
    This is a follow up post to this thread: https://supportforums.cisco.com/discussion/12400481/3702i-not-joint-2504
    Have been playing around with my AP's and made sure the time is correct on all the devices ( WLC and Switch). I have also moved the AP's to the same Vlan as the management IP of the WLC. 
    if I move the AP's to the same Vlan as the WLC they join and are happy, as soon as I move them to a different Vlan they cant join and there time goes back to the default plus they do not seem to save the WLC details to flash but still remember the test names I give them.
    it appears that option 43 is working fine as I can see it look for the WLC IP and I have done some trouble shooting on the WLC and it looks like it see's the AP but doesn't except it.
    please see below for the boot up of the AP and the WLC logs: 
    AP 
    IIOS Bootloader - Starting system.
    *** deleted for breverity ***** 
    Loading "flash:/ap3g2-k9w8-mx.153-3.JA1/ap3g2-k9w8-mx.153-3.JA1"...#########################
    File "flash:/ap3g2-k9w8-mx.153-3.JA1/ap3g2-k9w8-mx.153-3.JA1" uncompressed and installed, entry point: 0x2003000
    executing...
    Secondary Bootloader - Starting system.
    Montserrat Board
    *** deleted for breverity ***** 
    Boot CMD: 'boot  flash:/ap3g2-k9w8-mx.153-3.JA1/ap3g2-k9w8-xx.153-3.JA1;flash:/ap3g2-k9w8-mx.153-3.JA1/ap3g2-k9w8-xx.153-3.JA1'
    Loading "flash:/ap3g2-k9w8-mx.153-3.JA1/ap3g2-k9w8-xx.153-3.JA1"...###############################################
    File "flash:/ap3g2-k9w8-mx.153-3.JA1/ap3g2-k9w8-xx.153-3.JA1" uncompressed and installed, entry point: 0x1003000
    executing...
                  *** deleted for breverity ***** 
    cisco AIR-CAP3702I-Z-K9 (PowerPC) processor (revision A0) with 376810K/134656K bytes of memory.
    Processor board ID FGL1838X4T1
    PowerPC CPU at 800Mhz, revision number 0x2151
    Last reset from power-on
    LWAPP image version 8.0.110.0
    1 Gigabit Ethernet interface
    2 802.11 Radios
    32K bytes of flash-simulated non-volatile configuration memory.
    Base ethernet MAC Address: F4:4E:05:B7:1E:84
    Part Number                          : 73-15243-01
    PCA Assembly Number                  : 000-00000-00
    PCA Revision Number                  :
    PCB Serial Number                    : FOC18343WPR
    Top Assembly Part Number             : 068-05054-03
    Top Assembly Serial Number           : FGL1838X4T1
    Top Revision Number                  : A0
    Product/Model Number                 : AIR-CAP3702I-Z-K9
    % Please define a domain-name first.
    Press RETURN to get started!
    *Mar  1 00:00:19.295: %SOAP_FIPS-2-SELF_TEST_IOS_SUCCESS: IOS crypto FIPS self test passed (15)
    *Mar  1 00:00:19.755: Registering HW DTLS
    *Mar  1 00:00:19.763: APAVC: Initial WLAN Buffers Given to System is  2500
    *Mar  1 00:00:19.815: APAVC:  WlanPAKs 42878 RadioPaks  42270
    *Mar  1 00:00:22.127: %LINK-6-UPDOWN: Interface GigabitEthernet0, changed state to up
    *Mar  1 00:00:26.055: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 0 (4)
    *Mar  1 00:00:26.167: Loading Power Tables from ram:/Q2.bin. Class = A
    *Mar  1 00:00:26.167:  record size of 3ss: 1168 read_ptr: 4F9698E
    *Mar  1 00:00:31.207: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 1 (4)
    *Mar  1 00:00:31.251: Loading Power Tables from ram:/Q5.bin. Class = Z
    *Mar  1 00:00:31.251:  record size of vht: 2904 read_ptr: 4F9698E
    *Mar  1 00:00:31.407: Wait until the stile protocol list is initialized.
    *Mar  1 00:00:32.651: Start STILE Activation
    *Mar  1 00:00:34.571: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0, changed state to down
    *Mar  1 00:00:35.447: %SYS-5-RESTART: System restarted --
    Cisco IOS Software, C3700 Software (AP3G2-K9W8-M), Version 15.3(3)JA1, RELEASE SOFTWARE (fc1)
    Technical Support: http://www.cisco.com/techsupport
    Copyright (c) 1986-2014 by Cisco Systems, Inc.
    Compiled Fri 19-Dec-14 11:20 by prod_rel_team
    *Mar  1 00:00:35.447: %SNMP-5-COLDSTART: SNMP agent on host Test_1 is undergoing a cold start
    *Mar  1 00:00:36.563: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, changed state to up
    *Mar  1 00:00:37.787: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to uplwapp_crypto_init: MIC Present and Parsed Successfully
    *Mar  1 00:00:37.939: %SSH-5-ENABLED: SSH 2.0 has been enabled
    *Mar  1 00:00:37.939: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to up
    *Mar  1 00:00:38.987: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
    *Mar  1 00:00:38.987: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to down
    *Mar  1 00:00:47.567: %LINK-6-UPDOWN: Interface BVI1, changed state to down
    *Mar  1 00:00:48.567: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, changed state to down
    *Mar  1 00:00:50.431: %SOAP_FIPS-2-SELF_TEST_HW_SUCCESS: HW crypto FIPS self test passed (2-16)
    *Mar  1 00:00:50.431: DPAA Initialization Complete
    *Mar  1 00:00:50.431: %SYS-3-HARIKARI: Process DPAA INIT top-level routine exited
    *Mar  1 00:00:51.431: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0, changed state to up
    *Mar  1 00:00:53.435: %LINK-6-UPDOWN: Interface BVI1, changed state to up
    *Mar  1 00:00:53.867: Currently running a Release Image
    *Mar  1 00:00:54.287: Incorrect certificate in SHA2 PB !
    *Mar  1 00:00:54.287: Using SHA-1 signed certificate for image signing validation.
    *Mar  1 00:00:54.575: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, changed state to up
    *Mar  1 00:00:59.787: %DHCP-6-ADDRESS_ASSIGN: Interface BVI1 assigned DHCP address 10.1.20.2, mask 255.255.255.0, hostname Test_1
    *Mar  1 00:01:02.707: APAVC: Succeeded to activate all the STILE protocols.
    *Mar  1 00:01:02.707: APAVC: Registering with CFT
    *Mar  1 00:01:02.707: APAVC: CFT registration of delete callback succeeded
    *Mar  1 00:01:02.707: APAVC: Reattaching  Original Buffer pool for system use
    *Mar  1 00:01:02.707: Pool-ReAtach: paks 42878 radio42270
    %Default route without gateway, if not a point-to-point interface, may impact performance
    *Mar  1 00:01:10.103: AP image integrity check PASSED
    *Mar  1 00:01:10.187: Incorrect certificate in SHA2 PB !
    *Mar  1 00:01:10.203: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
    *Mar  1 00:01:10.203: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset
    *Mar  1 00:01:11.591: %CDP_PD-4-POWER_OK: 15.4 W power - NEGOTIATED inline power source
    *Mar  1 00:01:12.691: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to up
    *Mar  1 00:01:13.691: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
    *Mar  1 00:01:13.947: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to up
    *Mar  1 00:01:14.947: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to up
    *Mar  1 00:01:20.211: %SYS-6-LOGGINGHOST_STARTSTOP: Logging to host 255.255.255.255 port 514 CLI Request Triggered
    Translating "CISCO-CAPWAP-CONTROLLER"...domain server (255.255.255.255)
    *Mar  1 00:01:31.215: %CAPWAP-5-DHCP_OPTION_43: Controller address 10.1.1.231 obtained through DHCP
    *Mar  1 00:02:11.599: %CDP_PD-4-POWER_OK: Full power - NEGOTIATED inline power source
    *Mar  1 00:02:11.603: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to down
    *Mar  1 00:02:11.611: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
    *Mar  1 00:02:12.603: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
    *Mar  1 00:02:12.639: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to up
    *Mar  1 00:02:12.647: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to down
    *Mar  1 00:02:12.655: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset
    *Mar  1 00:02:13.639: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
    *Mar  1 00:02:13.647: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to down
    *Mar  1 00:02:13.699: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to up
    *Mar  1 00:02:14.699: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to up
    Not in Bound state.
    *Mar  1 00:02:44.719: %CAPWAP-3-DHCP_RENEW: Could not discover WLC. Either IP address is not assigned or assigned IP is wrong. Renewing DHCP IP.
    *Mar  1 00:02:49.839: %DHCP-6-ADDRESS_ASSIGN: Interface BVI1 assigned DHCP address 10.1.20.3, mask 255.255.255.0, hostname Test_1
    Translating "CISCO-CAPWAP-CONTROLLER"...domain server (255.255.255.255)
    *Mar  1 00:02:55.719: %CAPWAP-5-DHCP_OPTION_43: Controller address 10.1.1.231 obtained through DHCP
    Not in Bound state.
    *Mar  1 00:03:59.219: %CAPWAP-3-DHCP_RENEW: Could not discover WLC. Either IP address is not assigned or assigned IP is wrong. Renewing DHCP IP.
    *Mar  1 00:04:04.343: %DHCP-6-ADDRESS_ASSIGN: Interface BVI1 assigned DHCP address 10.1.20.4, mask 255.255.255.0, hostname Test_1
    Translating "CISCO-CAPWAP-CONTROLLER"...domain server (255.255.255.255)
    *Mar  1 00:04:10.223: %CAPWAP-5-DHCP_OPTION_43: Controller address 10.1.1.231 obtained through DHCP
    WLC: 
    isco Controller) >show time
    Time............................................. Tue Jan 27 17:44:47 2015
    Timezone delta................................... 0:0
    Timezone location................................ (GMT +8:00) HongKong, Bejing, Chongquing
    NTP Servers
        NTP Polling Interval.........................     3600
         Index     NTP Key Index                  NTP Server                  NTP Msg Auth Status
           1              0                             150.101.176.226       AUTH DISABLED
    (Cisco Controller) >show ap join stats summary  
    Incorrect input! Use 'show ap join stats summary [all/<ap-mac>]'
    (Cisco Controller) >show ap join stats summary all 
    Number of APs.............................................. 2 
    Base Mac             AP EthernetMac       AP Name                 IP Address         Status
    f4:4e:05:aa:a6:a0    f4:4e:05:94:c3:98    APf44e.0594.c398        10.1.1.22          Joined    
    f4:4e:05:b6:ce:f0    N A                  Test_1                  10.1.20.7          Not Joined
    (Cisco Controller) >show ap join stats detailed f4:4e:05:b6:ce:f0
    Sync phase statistics
    - Time at sync request received............................ Not applicable
    - Time at sync completed................................... Not applicable
    Discovery phase statistics
    - Discovery requests received.............................. 45
    - Successful discovery responses sent...................... 21
    - Unsuccessful discovery request processing................ 24
    - Reason for last unsuccessful discovery attempt........... Layer 3 discovery request not received on management VLAN
    - Time at last successful discovery attempt................ Jan 27 17:45:49.705
    - Time at last unsuccessful discovery attempt.............. Jan 27 17:45:49.705
    Join phase statistics
    - Join requests received................................... 0
    - Successful join responses sent........................... 0
    - Unsuccessful join request processing..................... 0
    - Reason for last unsuccessful join attempt................ Not applicable
    - Time at last successful join attempt..................... Not applicable
    - Time at last unsuccessful join attempt................... Not applicable
    Configuration phase statistics
    --More-- or (q)uit
    - Configuration requests received.......................... 0
    - Successful configuration responses sent.................. 0
    - Unsuccessful configuration request processing............ 0
    - Reason for last unsuccessful configuration attempt....... Not applicable
    - Time at last successful configuration attempt............ Not applicable
    - Time at last unsuccessful configuration attempt.......... Not applicable
    Last AP message decryption failure details
    - Reason for last message decryption failure............... Not applicable
    Last AP disconnect details
    - Reason for last AP connection failure.................... Not applicable
    - Last AP disconnect reason................................ Not applicable
    Last join error summary
    - Type of error that occurred last......................... Lwapp discovery request rejected
    - Reason for error that occurred last...................... Layer 3 discovery request not received on management VLAN
    - Time at which the last join error occurred............... Jan 27 17:45:49.705
    AP disconnect details
    - Reason for last AP connection failure.................... Not applicable
                                                                               Ethernet Mac : 00:00:00:00:00:00  Ip Address : 10.1.20.7
    (Cisco Controller) >show interface summary 
     Number of Interfaces.......................... 4
    Interface Name                   Port Vlan Id  IP Address      Type    Ap Mgr Guest
    ap                               LAG  20       10.1.20.231     Dynamic No     No   
    guest                            LAG  30       10.1.30.231     Dynamic No     No   
    management                       LAG  10       10.1.1.231      Static  Yes    No   
    virtual                          N/A  N/A      1.1.1.1         Static  No     No   
    SWITCH
    witch#show run
    Building configuration...
    *** deleted for breverity ***** 
    no aaa new-model
    clock timezone AWST 8
    system mtu routing 1500
    ip routing
    ip dhcp pool WAP_Pool
       network 10.1.20.0 255.255.255.0
       default-router 10.1.20.1 
       option 43 hex f104.0a01.01e7
    ip dhcp pool Clients
       network 10.1.30.0 255.255.255.0
       default-router 10.1.30.1 
       dns-server 203.0.178.191 
    ip dhcp pool test
       network 10.1.1.0 255.255.255.0
       default-router 10.1.1.1 
    crypto pki trustpoint TP-self-signed-4082587776
     enrollment selfsigned
     subject-name cn=IOS-Self-Signed-Certificate-4082587776
     revocation-check none
     rsakeypair TP-self-signed-4082587776
    *** deleted for breverity ***** 
    *** deleted for breverity ***** !
    interface FastEthernet0/3
     description *** WLC ****
     switchport trunk encapsulation dot1q
     switchport mode trunk
    interface FastEthernet0/4
     description **** AP *****
     switchport access vlan 20
     switchport mode access
     spanning-tree portfast
    interface FastEthernet0/5
     description **** AP ****
     switchport access vlan 20
     switchport mode access
     spanning-tree portfast
    interface FastEthernet0/6
    i*** deleted for breverity ***** !
    interface Vlan10
     description *** Managment ***
     ip address 10.1.1.230 255.255.255.0
    interface Vlan20
     description *** WIRELESS APS ***
     ip address 10.1.20.1 255.255.255.0
    interface Vlan30
     ip address 10.1.30.1 255.255.255.0
    ip classless
    ip route 0.0.0.0 0.0.0.0 10.1.1.1
    ip http server
    ip http secure-server
    ip sla enable reaction-alerts
    l*** deleted for breverity ***** 
    ntp clock-period 36028827
    ntp source FastEthernet0/1
    ntp server 121.0.0.42
    ntp server 202.127.210.37
    end
    I have also placed a Device in Vlan 20 and it is able to ping the WLC and the WLC can ping it s routing is working. 
    Thanks 

    Hey Scott, 
    I gave that a shot and still no luck, log's from AP boot up:
    IIOS Bootloader - Starting system.
    flash is writable
    Tide XL MB - 40MB of flash
    Xmodem file system is available.
    flashfs[0]: 67 files, 9 directories
    flashfs[0]: 0 orphaned files, 0 orphaned directories
    flashfs[0]: Total bytes: 41158656
    flashfs[0]: Bytes used: 20894208
    flashfs[0]: Bytes available: 20264448
    flashfs[0]: flashfs fsck took 20 seconds.
    Base Ethernet MAC address: f4:4e:05:b7:1e:84
    Ethernet speed is 100 Mb - FULL Duplex
    Loading "flash:/ap3g2-k9w8-mx.153-3.JA1/ap3g2-k9w8-mx.153-3.JA1"...#########################
    File "flash:/ap3g2-k9w8-mx.153-3.JA1/ap3g2-k9w8-mx.153-3.JA1" uncompressed and installed, entry point: 0x2003000
    executing...
    Secondary Bootloader - Starting system.
    Montserrat Board
    40MB format
    Tide XL MB - 40MB of flash
    Xmodem file system is available.
    flashfs[0]: 67 files, 9 directories
    flashfs[0]: 0 orphaned files, 0 orphaned directories
    flashfs[0]: Total bytes: 41158656
    flashfs[0]: Bytes used: 20894208
    flashfs[0]: Bytes available: 20264448
    flashfs[0]: flashfs fsck took 21 seconds.
    flashfs[1]: 0 files, 1 directories
    flashfs[1]: 0 orphaned files, 0 orphaned directories
    flashfs[1]: Total bytes: 12257280
    flashfs[1]: Bytes used: 1024
    flashfs[1]: Bytes available: 12256256
    flashfs[1]: flashfs fsck took 1 seconds.
    Base Ethernet MAC address: f4:4e:05:b7:1e:84
    Boot CMD: 'boot  flash:/ap3g2-k9w8-mx.153-3.JA1/ap3g2-k9w8-xx.153-3.JA1;flash:/ap3g2-k9w8-mx.153-3.JA1/ap3g2-k9w8-xx.153-3.JA1'
    Loading "flash:/ap3g2-k9w8-mx.153-3.JA1/ap3g2-k9w8-xx.153-3.JA1"...###############################################
    File "flash:/ap3g2-k9w8-mx.153-3.JA1/ap3g2-k9w8-xx.153-3.JA1" uncompressed and installed, entry point: 0x1003000
    executing...
                  Restricted Rights Legend
    Use, duplication, or disclosure by the Government is
    subject to restrictions as set forth in subparagraph
    (c) of the Commercial Computer Software - Restricted
    Rights clause at FAR sec. 52.227-19 and subparagraph
    (c) (1) (ii) of the Rights in Technical Data and Computer
    Software clause at DFARS sec. 252.227-7013.
               cisco Systems, Inc.
               170 West Tasman Drive
               San Jose, California 95134-1706
    Cisco IOS Software, C3700 Software (AP3G2-K9W8-M), Version 15.3(3)JA1, RELEASE SOFTWARE (fc1)
    Technical Support: http://www.cisco.com/techsupport
    Copyright (c) 1986-2014 by Cisco Systems, Inc.
    Compiled Fri 19-Dec-14 11:20 by prod_rel_team
    Montserrat Board
    40MB format
    Tide XL MB - 40MB of flash
    Initializing flashfs...
    flashfs[2]: 67 files, 9 directories
    flashfs[2]: 0 orphaned files, 0 orphaned directories
    flashfs[2]: Total bytes: 40900608
    flashfs[2]: Bytes used: 20894208
    flashfs[2]: Bytes available: 20006400
    flashfs[2]: flashfs fsck took 14 seconds.
    flashfs[2]: Initialization complete.
    flashfs[4]: 0 files, 1 directories
    flashfs[4]: 0 orphaned files, 0 orphaned directories
    flashfs[4]: Total bytes: 11999232
    flashfs[4]: Bytes used: 1024
    flashfs[4]: Bytes available: 11998208
    flashfs[4]: flashfs fsck took 0 seconds.
    flashfs[4]: Initialization complete.
    Copying radio files from flash: to ram:
    Copy in progress...CCCCC
    Copy in progress...CCC
    Copy in progress...CCCC
    Copy in progress...CCCC
    Copy in progress...CC
    Copy in progress...CCCC
    Copy in progress...CC
    Copy in progress...CCCCC
    Copy in progress...CCCC
    Copy in progress...CC
    Uncompressing radio files...
    ...done Initializing flashfs.
    Radio0  present 8764 8000 0 A8000000 A8010000 0
    Rate table has 650 entries (20 legacy/224 11n/406 11ac)
    POWER TABLE FILENAME = ram:/Q2.bin
    Radio1  present 8864 8000 0 80000000 80100000 4
    POWER TABLE FILENAME = ram:/Q5.bin
    Radio2 not present 0 0 0 0 0 8
    This product contains cryptographic features and is subject to United
    States and local country laws governing import, export, transfer and
    use. Delivery of Cisco cryptographic products does not imply
    third-party authority to import, export, distribute or use encryption.
    Importers, exporters, distributors and users are responsible for
    compliance with U.S. and local country laws. By using this product you
    agree to comply with applicable laws and regulations. If you are unable
    to comply with U.S. and local laws, return this product immediately.
    A summary of U.S. laws governing Cisco cryptographic products may be found at:
    http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
    If you require further assistance please contact us by sending email to
    [email protected].
    cisco AIR-CAP3702I-Z-K9 (PowerPC) processor (revision A0) with 376810K/134656K bytes of memory.
    Processor board ID FGL1838X4T1
    PowerPC CPU at 800Mhz, revision number 0x2151
    Last reset from power-on
    LWAPP image version 8.0.110.0
    1 Gigabit Ethernet interface
    2 802.11 Radios
    32K bytes of flash-simulated non-volatile configuration memory.
    Base ethernet MAC Address: F4:4E:05:B7:1E:84
    Part Number                          : 73-15243-01
    PCA Assembly Number                  : 000-00000-00
    PCA Revision Number                  :
    PCB Serial Number                    : FOC18343WPR
    Top Assembly Part Number             : 068-05054-03
    Top Assembly Serial Number           : FGL1838X4T1
    Top Revision Number                  : A0
    Product/Model Number                 : AIR-CAP3702I-Z-K9
    % Please define a domain-name first.
    Press RETURN to get started!
    *Mar  1 00:00:19.295: %SOAP_FIPS-2-SELF_TEST_IOS_SUCCESS: IOS crypto FIPS self test passed (15)
    *Mar  1 00:00:19.755: Registering HW DTLS
    *Mar  1 00:00:19.763: APAVC: Initial WLAN Buffers Given to System is  2500
    *Mar  1 00:00:19.815: APAVC:  WlanPAKs 42878 RadioPaks  42270
    *Mar  1 00:00:22.127: %LINK-6-UPDOWN: Interface GigabitEthernet0, changed state to up
    *Mar  1 00:00:26.055: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 0 (4)
    *Mar  1 00:00:26.167: Loading Power Tables from ram:/Q2.bin. Class = A
    *Mar  1 00:00:26.167:  record size of 3ss: 1168 read_ptr: 4F9698E
    *Mar  1 00:00:31.207: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 1 (4)
    *Mar  1 00:00:31.251: Loading Power Tables from ram:/Q5.bin. Class = Z
    *Mar  1 00:00:31.251:  record size of vht: 2904 read_ptr: 4F9698E
    *Mar  1 00:00:31.407: Wait until the stile protocol list is initialized.
    *Mar  1 00:00:32.651: Start STILE Activation
    *Mar  1 00:00:34.571: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0, changed state to down
    *Mar  1 00:00:35.447: %SYS-5-RESTART: System restarted --
    Cisco IOS Software, C3700 Software (AP3G2-K9W8-M), Version 15.3(3)JA1, RELEASE SOFTWARE (fc1)
    Technical Support: http://www.cisco.com/techsupport
    Copyright (c) 1986-2014 by Cisco Systems, Inc.
    Compiled Fri 19-Dec-14 11:20 by prod_rel_team
    *Mar  1 00:00:35.447: %SNMP-5-COLDSTART: SNMP agent on host Test_1 is undergoing a cold start
    *Mar  1 00:00:36.563: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, changed state to up
    *Mar  1 00:00:37.787: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to uplwapp_crypto_init: MIC Present and Parsed Successfully
    *Mar  1 00:00:37.939: %SSH-5-ENABLED: SSH 2.0 has been enabled
    *Mar  1 00:00:37.939: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to up
    *Mar  1 00:00:38.987: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
    *Mar  1 00:00:38.987: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to down
    *Mar  1 00:00:47.567: %LINK-6-UPDOWN: Interface BVI1, changed state to down
    *Mar  1 00:00:48.567: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, changed state to down
    *Mar  1 00:00:50.431: %SOAP_FIPS-2-SELF_TEST_HW_SUCCESS: HW crypto FIPS self test passed (2-16)
    *Mar  1 00:00:50.431: DPAA Initialization Complete
    *Mar  1 00:00:50.431: %SYS-3-HARIKARI: Process DPAA INIT top-level routine exited
    *Mar  1 00:00:51.431: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0, changed state to up
    *Mar  1 00:00:53.435: %LINK-6-UPDOWN: Interface BVI1, changed state to up
    *Mar  1 00:00:53.867: Currently running a Release Image
    *Mar  1 00:00:54.287: Incorrect certificate in SHA2 PB !
    *Mar  1 00:00:54.287: Using SHA-1 signed certificate for image signing validation.
    *Mar  1 00:00:54.575: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, changed state to up
    *Mar  1 00:00:59.787: %DHCP-6-ADDRESS_ASSIGN: Interface BVI1 assigned DHCP address 10.1.20.2, mask 255.255.255.0, hostname Test_1
    *Mar  1 00:01:02.707: APAVC: Succeeded to activate all the STILE protocols.
    *Mar  1 00:01:02.707: APAVC: Registering with CFT
    *Mar  1 00:01:02.707: APAVC: CFT registration of delete callback succeeded
    *Mar  1 00:01:02.707: APAVC: Reattaching  Original Buffer pool for system use
    *Mar  1 00:01:02.707: Pool-ReAtach: paks 42878 radio42270
    %Default route without gateway, if not a point-to-point interface, may impact performance
    *Mar  1 00:01:10.103: AP image integrity check PASSED
    *Mar  1 00:01:10.187: Incorrect certificate in SHA2 PB !
    *Mar  1 00:01:10.203: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
    *Mar  1 00:01:10.203: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset
    *Mar  1 00:01:11.591: %CDP_PD-4-POWER_OK: 15.4 W power - NEGOTIATED inline power source
    *Mar  1 00:01:12.691: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to up
    *Mar  1 00:01:13.691: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
    *Mar  1 00:01:13.947: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to up
    *Mar  1 00:01:14.947: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to up
    *Mar  1 00:01:20.211: %SYS-6-LOGGINGHOST_STARTSTOP: Logging to host 255.255.255.255 port 514 CLI Request Triggered
    Translating "CISCO-CAPWAP-CONTROLLER"...domain server (255.255.255.255)
    *Mar  1 00:01:31.215: %CAPWAP-5-DHCP_OPTION_43: Controller address 10.1.1.231 obtained through DHCP
    *Mar  1 00:02:11.599: %CDP_PD-4-POWER_OK: Full power - NEGOTIATED inline power source
    *Mar  1 00:02:11.603: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to down
    *Mar  1 00:02:11.611: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
    *Mar  1 00:02:12.603: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
    *Mar  1 00:02:12.639: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to up
    *Mar  1 00:02:12.647: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to down
    *Mar  1 00:02:12.655: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset
    *Mar  1 00:02:13.639: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
    *Mar  1 00:02:13.647: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to down
    *Mar  1 00:02:13.699: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to up
    *Mar  1 00:02:14.699: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to up
    Not in Bound state.
    *Mar  1 00:02:44.719: %CAPWAP-3-DHCP_RENEW: Could not discover WLC. Either IP address is not assigned or assigned IP is wrong. Renewing DHCP IP.
    *Mar  1 00:02:49.839: %DHCP-6-ADDRESS_ASSIGN: Interface BVI1 assigned DHCP address 10.1.20.3, mask 255.255.255.0, hostname Test_1
    Translating "CISCO-CAPWAP-CONTROLLER"...domain server (255.255.255.255)
    *Mar  1 00:02:55.719: %CAPWAP-5-DHCP_OPTION_43: Controller address 10.1.1.231 obtained through DHCP
    Not in Bound state.
    *Mar  1 00:03:59.219: %CAPWAP-3-DHCP_RENEW: Could not discover WLC. Either IP address is not assigned or assigned IP is wrong. Renewing DHCP IP.
    *Mar  1 00:04:04.343: %DHCP-6-ADDRESS_ASSIGN: Interface BVI1 assigned DHCP address 10.1.20.4, mask 255.255.255.0, hostname Test_1
    Translating "CISCO-CAPWAP-CONTROLLER"...domain server (255.255.255.255)
    *Mar  1 00:04:10.223: %CAPWAP-5-DHCP_OPTION_43: Controller address 10.1.1.231 obtained through DHCP

  • After I did a reset my gps app will not receive signals from my remote G PS device. I have an iPad 2 wi-if only. The remote GPS device is pared and has a strong signal. I reinstalled my gps app, no luck.

    After I did a reset my gps apps will not receive a signal from my remote GPS receiver. The GPS app wa working fine before. I reloaded the app but no luck. My remote GPS receiver is paired to my iPad and has a strong signal.

    Hi there.
    Thank you very much for your quick reply, it's really appreciated.
    No need to apologize, I actually found the phrase "If your iPad ever craps the bed" amusing under the circumstances
    I checked the list of installed apps like you suggested (Settings>General>Usage>Storage>Show all apps) but this problem app is not in the list. I have also swiped down on the home screen to search for it, but again it does not show.
    While it has not let me download the app (and I just tried it again) it has helped me to eliminate a few things from the list of what to try, and I can definitely conclude that it has not downloaded.
    I guess I need to fire up my PC and download it / sync my iPad.
    Thanks again for your help

  • Firefox 5 with Fedora 15 prints text, but will not print images from web pages.

    I have a Pentium 3 laptop running Fedora 15 and using Firefox 5.0. Firefox will print the text from a website, but will not print the images. It just leaves the spaces blank where the images should be. Print preview shows the same results. I have a AMD desktop and a Pentium 4 laptop running the same software, except that the desktop is running the 64-bit version of Fedora 15 and the second laptop is running the 32-bit version. The desktop prints the text and images without very many problems, but both laptops will print the text, but ''not'' the images.
    As a test, I downgraded Firefox from version 5.0 to 4.0.1 on the Pentium 4 laptop and encountered the same problem. So, since I do not print much from either laptop, I had not before seen this problem. The desktop has never seen it.
    I figure it may be an about:config problem, but I do not know what the parameter may be that is causing the problem.

    See this: <br />
    http://kb.mozillazine.org/Problems_printing_web_pages

  • My desktop m8407c powers up, but will not wake monitor from sleep.

    I have a pavilion desktop m8407c running vista 64 that turns the fan on and sounds like it is running, but will not alert the keyboard or monitor.  It hums and powers up to some extent, but the hum does not stop or wake the monitor from sleep.  I have tried unplugging and disconnecting everything, but it continues to do the same thing.  Any help would be appreciated.

    Hello sap22
    Follow the steps outlined in the article below. Let me know if the problem persists.
    Monitor or TV is Blank after Starting the Computer
    Don't forgot to say thanks by giving "Kudos" to those that help solve your problems.
    When a solution is found please mark the post that solves your issue.

  • Mail sends but will not receive gmail

    I just upgraded to a new iMac and transferred all my data via Time Machine.  My mail app will send emails but not recieve them.  yesterday after reading on here that making a new account, I could fix this, I found that I I now cannot see any of my past received emails.  That's very troubling. 
    Anyway, any ideas on why mail would send but not receive gmail? 
    Thanks!

    Bruce Bridges wrote:
    any ideas on why mail would send but not receive gmail?
    What do you see for that account if you invoke Mail's menu option Window > Connection Doctor?
    Pay particular attention to the settings under the "Advanced" tab for that account in the Mail preference "Accounts" panel.

  • ICal on MacBook Pro will not receive dates from iPhone, but iPhone will receive dates from iCal on MacBook

    I recently got a MacBook Pro after having an iPhone and iPad since last year.  I have iCloud set up on all devices to share calendar dates.  However, when I input an event on iCal on the MacBook everything is fine and the event shows up on my iPhone and iPad calendars, but when I input an appointment on my iPhone, it will not update to the iCal on MacBook.
    Help please?

    First check that all your settings are correct, that calendar syncing is checked on all devices (system preferences > iCloud on a mac and settings > iCloud on a iPhone, iPad or iPod).
    Make sure the calendars you are using are in your 'iCloud' account and not an 'On My Mac', 'On My Phone' or other non iCloud account (you can do this by clicking/tapping the calendar button in the top left corner of the application ), non iCloud calendars will not sync.
    If you are sure that everything is set up correctly and your calendars are in the iCloud account, you might try unchecking calendar syncing in the iCloud settings, restarting your device and then re-enabling calendar syncing settings.

  • Thunderbird will not receive attachments from my Yahoo email

    I frequently mail attachments from my Yahoo address to Thunderbird address. Recently these messages stopped arriving in my inbox. Thunderbird receives attachments from other sources, mostly sending to myself for testing. Yahoo sends attachments to other addresses as I have tested on several friends. It appears that the Yahoo account is performing as it should. One other clue I worry about is that I never ever see spam or junk emails in Thunderbird and I have no idea where they go.
    Thanks to anyone willing to give advice. Roger

    You don't have a Thunderbird account. You do have an account, probably provided by your ISP, which you access via Thunderbird. Go to your email provider's website and look there for Spam settings and maybe any limits or blocks that might prevent you getting attachments.

  • My mail account is set up correctly but will not receive or send email?

    My outlook email account works fine and it has automatically synchronised the set up / account information to my iphone 4s via itunes when syncing. However I cannot receive or send emails! Anyone know of the reason for this?

    Do not attempt to sync email accounts. Security features hardly ever allow this to work without any edditing. Contact your email provider to find out the settings and servers they are using for mobile devices and then remove the existing account from settings, mail contacts calendars and create a new acccount there. After the setup is finished check all the settings of the crated acccount to ensure all sections are populated with information. Especialöly it might be neccessary to fill some fields in the smtp primary ßerver settings that are rated as optional.

  • HT4796 my mac has showed up with the passcode but will not move on from there what do i do?

    help i dont know what im doing?!

    These are iTunes purchases?
    You are doing this in iTunes (keep me guessing here...)?
    You double click on a track (in iTunes?) and absolutely nothing happens?
    If these are not iTunes purchases then we will need to know a lot more about the file type.

Maybe you are looking for

  • Is the canvas something like "the final output"? Or is that the viewer?

    I am making a video of my HD footage i shot with my Full HD Camcorder (Sony HDR-SR12). When i go through te timeline and play something, it shows fully in my viewer, but in the canvas i get only a selection of the full image (it seems that it is zoom

  • Cable, seems to be stuck in step 2?

    I purchased a CA-53 CA53 USB DATA CABLE and driver.  The driver seemed to install perfectly and I can open the PC Suite main options center.  I have tried several times unsuccessfully to connect my Nokia (6126) to the computer using the data cable to

  • EBP Business Packages

    Hi does somebody know whether EBP business packages are still available for EP 6.20? I have not found anything. Thanks

  • Please help. Cannot find symbol Error!

    I have been working on this code for days now. It keeps coming up with errors. The error says cannot find symbol. I will bold the areas that say that. I got it down to 23 from 42 but now I have no idea what the problem is. any help is greatly appreci

  • 60i AVCHD footage transfer in with jagged edges.  What am I missing?

    I'm logging and transfering in Final Cut Express.  The Canon C100 I just got uses AVCHD in the .mts files.  Express has no problem recognizing the card in my SD card reader.  I select AVCHD - Apple Intermediate Codec 1920x1080i60 in the easy setup.