WLC redundancy with prime
Hi all,
We are going to implement high availabilty in 5508 WLC with version of 7.3.101 . We will be using Prime infrastructure 1.2 for monitoring purpose.
With Prime , whether we can monitor and manage redundant WLC also or only active WLC?...
Thanks for your help.......
I just know from experience. You can only GUI/ssh into the primary WLC when you enable AP-SSO. So once the pairs are in HA, that is it.... You have only the primary WLC IP address available. You learn things the hard way sometimes because there are things not documented.
Sent from Cisco Technical Support iPhone App
Similar Messages
-
Hello,
I have question regarding N+1 redundancy with 2504-HA WLC.
Can I use 2504-HA unit for H+1 redundancy? SSO is not needed
I have two wireless network:
1. With WLC 5508 with about 40 AP(1262), all them are A regulatory domain
2. With WLC 2504, with about 30 Mesh AP(1552), all of them are E regulatory domain
I plan to use two 2504-HA units for backups, one for network with WLC5508 and second for network with WLC2504.
In case N+1 redundancy is management with Prime mandatory ?Hi,
Better to use same model and same software.
Case1: You have 5508WLC
Solution from my side: You must buy a another WLC with HA SKU license(Zero AP license). This wlc can work as N+1 and AP SSO as well as Client SSO but with higher version of code(7.5 or higher).
Case2: You have 2504 WLC
Solution: You must buy a another 2504 HA WLC: AIR-CT2504-HA-K9, that only supports N+1(No AP SSO and NO Client SSO)
http://www.cisco.com/c/en/us/td/docs/wireless/technology/hi_avail/N1_High_Availability_Deployment_Guide/N1_HA_Overview.html
More info:
http://www.cisco.com/c/en/us/products/collateral/wireless/aironet-1130-ag-series/qa_c67-714540.pdf
Regards
Dont forget to rate helpful posts -
Cannot add WLC 5508 to Prime Infrastructure 2.1
Regards,
I've been migrating / implementing a WCS to PI 2.1. I had several problems at first to add the 11 WLC we have to PI which I could be solving by trying and testing as I have not found many references by Cisco when it comes to troubleshooting when deploying PI.
I have several queries:
1. The WCS was added 11 WLC using different SNMP communities are configured on each of them. At first when trying to add the WLC had PI SNMP communication problems. I performed the test to eliminate any of the WLC added to WCS and add it again with some communities already existing R / W without any problem. At the end, I could not add the WLC so I had to create an SNMP community with the IP of Prime in the WLC so that they can be added. Does anyone know what is the cause of this?
2. I could not add a WLC 5508 IOS 7.3 using this method, even creating an SNMP community and IP mask 0.0.0.0 / 0. No access list or FW in between the WLC These WLC are spread over several countries but i was able to add the other WLC adding a community in each WLC pointing to the IP of Prime. It is similar to this case:
https://supportforums.cisco.com/discussion/12232506/cannot-add-wlc-5508-v761200-prime-infrastructure-21
Thanks for the help.It turns out that this situation was caused by a bug in 7.6.120.0 (CSCuo73572).
TAC handed me an escalation image (7.6.120.16) that fixed this.
Added the controllers sucessfully on the first try.
Phill -
I have a Problem with Romming Between SSIDs withing the same WLC but with deferent VLAN .
HI All,
I have a Problem with Romming Between SSIDs withing the same WLC but with deferent VLAN . the WLC are providing the HQ and one of the Branches the Wireless services .
Am using all the available 9 SSIDs at the HQ , and am using only 4 of it at the Brnche.
The problem that i have are happening only at the Branch office as i cant room between the SSIDs within Diferent VLANs but i can do it with the one that pointing to the same VLAN. Once the client ( Laptop/Phone ) connected to one of the SSIDs. it imposiible to have him connected to the other ones with Different VLAN. meanwhile, It says its connected to the other SSID but its not getting IP from that pool.
here is the Show Run-Config from my WLC .. and the Problem happening between the SSID AMOBILE and ASTAFF. i have the Debug while am switching between the SSIDs if needed .
=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2013.11.04 10:20:47 =~=~=~=~=~=~=~=~=~=~=~=
show run-config
Press Enter to continue...
System Inventory
NAME: "Chassis" , DESCR: "Cisco 5500 Series Wireless LAN Controller"
PID: AIR-CT5508-K9, VID: V01, SN: FCW1535L01G
Burned-in MAC Address............................ 30:E4:DB:1B:99:80
Power Supply 1................................... Present, OK
Power Supply 2................................... Absent
Maximum number of APs supported.................. 12
Press Enter to continue or <ctrl-z> to abort
System Information
Manufacturer's Name.............................. Cisco Systems Inc.
Product Name..................................... Cisco Controller
Product Version.................................. 7.0.235.0
Bootloader Version............................... 1.0.1
Field Recovery Image Version..................... 6.0.182.0
Firmware Version................................. FPGA 1.3, Env 1.6, USB console 1.27
Build Type....................................... DATA + WPS
System Name...................................... WLAN Controller 5508
System Location..................................
System Contact...................................
System ObjectID.................................. 1.3.6.1.4.1.9.1.1069
IP Address....................................... 10.125.18.15
Last Reset....................................... Software reset
System Up Time................................... 41 days 5 hrs 14 mins 42 secs
System Timezone Location......................... (GMT -5:00) Eastern Time (US and Canada)
Current Boot License Level....................... base
Current Boot License Type........................ Permanent
Next Boot License Level.......................... base
Next Boot License Type........................... Permanent
Configured Country............................... US - United States
--More or (q)uit current module or <ctrl-z> to abort
Operating Environment............................ Commercial (0 to 40 C)
Internal Temp Alarm Limits....................... 0 to 65 C
Internal Temperature............................. +36 C
External Temperature............................. +20 C
Fan Status....................................... OK
State of 802.11b Network......................... Enabled
State of 802.11a Network......................... Enabled
Number of WLANs.................................. 10
Number of Active Clients......................... 61
Burned-in MAC Address............................ 30:E4:DB:1B:99:80
Power Supply 1................................... Present, OK
Power Supply 2................................... Absent
Maximum number of APs supported.................. 12
Press Enter to continue or <ctrl-z> to abort
AP Bundle Information
Primary AP Image Size
ap3g1 5804
ap801 5192
ap802 5232
c1100 3096
c1130 4972
c1140 4992
c1200 3364
c1240 4812
c1250 5512
c1310 3136
c1520 6412
c3201 4324
c602i 3716
Secondary AP Image Size
ap801 4964
c1100 3036
--More or (q)uit current module or <ctrl-z> to abort
c1130 4884
c1140 4492
c1200 3316
c1240 4712
c1250 5064
c1310 3084
c1520 5244
c3201 4264
Press Enter to continue or <ctrl-z> to abort
Switch Configuration
802.3x Flow Control Mode......................... Disable
FIPS prerequisite features....................... Disabled
secret obfuscation............................... Enabled
Strong Password Check Features:
case-check ...........Enabled
consecutive-check ....Enabled
default-check .......Enabled
username-check ......Enabled
Press Enter to continue or <ctrl-z> to abort
Network Information
RF-Network Name............................. OGR
Web Mode.................................... Disable
Secure Web Mode............................. Enable
Secure Web Mode Cipher-Option High.......... Disable
Secure Web Mode Cipher-Option SSLv2......... Enable
OCSP........................................ Disabled
OCSP responder URL..........................
Secure Shell (ssh).......................... Enable
Telnet...................................... Disable
Ethernet Multicast Forwarding............... Disable
Ethernet Broadcast Forwarding............... Disable
AP Multicast/Broadcast Mode................. Unicast
IGMP snooping............................... Disabled
IGMP timeout................................ 60 seconds
IGMP Query Interval......................... 20 seconds
User Idle Timeout........................... 300 seconds
ARP Idle Timeout............................ 300 seconds
Cisco AP Default Master..................... Enabled
AP Join Priority............................ Disable
Mgmt Via Wireless Interface................. Disable
Mgmt Via Dynamic Interface.................. Disable
--More or (q)uit current module or <ctrl-z> to abort
Bridge MAC filter Config.................... Enable
Bridge Security Mode........................ EAP
Mesh Full Sector DFS........................ Enable
AP Fallback ................................ Enable
Web Auth Redirect Ports .................... 80
Web Auth Proxy Redirect ................... Disable
Fast SSID Change ........................... Enabled
AP Discovery - NAT IP Only ................. Enabled
IP/MAC Addr Binding Check .................. Enabled
Press Enter to continue or <ctrl-z> to abort
Port Summary
STP Admin Physical Physical Link Link
Pr Type Stat Mode Mode Status Status Trap POE SFPType
1 Normal Forw Enable Auto 1000 Full Up Enable N/A 1000BaseTX
2 Normal Disa Enable Auto Auto Down Enable N/A Not Present
3 Normal Disa Enable Auto Auto Down Enable N/A Not Present
4 Normal Disa Enable Auto Auto Down Enable N/A Not Present
5 Normal Disa Enable Auto Auto Down Enable N/A Not Present
6 Normal Disa Enable Auto Auto Down Enable N/A Not Present
7 Normal Disa Enable Auto Auto Down Enable N/A Not Present
8 Normal Disa Enable Auto Auto Down Enable N/A Not Present
Press Enter to continue or <ctrl-z> to abort
AP Summary
Number of APs.................................... 8
Global AP User Name.............................. Not Configured
Global AP Dot1x User Name........................ Not Configured
AP Name Slots AP Model Ethernet MAC Location Port Country Priority
KNOWLOGY_DC01 2 AIR-LAP1131AG-A-K9 00:1d:45:86:ed:4e KNOWLOGY_DC_Serv 1 US 1
KNOWLOGY_DC02 2 AIR-LAP1131AG-A-K9 00:21:d8:36:c5:c4 KNOWLOGY_DC_Serv 1 US 1
KN1252_AP01 2 AIR-LAP1252AG-A-K9 00:21:d8:ef:06:50 Knowlogy Confere 1 US 1
KN1252_AP02 2 AIR-LAP1252AG-A-K9 00:22:55:8e:2e:d4 Server Room Side 1 US 1
Anham_AP03 2 AIR-LAP1142N-A-K9 70:81:05:88:15:b5 default location 1 US 1
ANHAM_AP01 2 AIR-LAP1142N-A-K9 70:81:05:b0:e4:62 Small Conference 1 US 1
ANHAM_AP04 2 AIR-LAP1131AG-A-K9 00:1d:45:86:e1:b8 Conference room 1 US 1
ANHAM_AP02 2 AIR-LAP1142N-A-K9 70:81:05:96:7a:49 Copy Room 1 US 1
AP Tcp-Mss-Adjust Info
AP Name TCP State MSS Size
KNOWLOGY_DC01 disabled -
KNOWLOGY_DC02 disabled -
--More or (q)uit current module or <ctrl-z> to abort
KN1252_AP01 disabled -
KN1252_AP02 disabled -
Anham_AP03 disabled -
ANHAM_AP01 disabled -
ANHAM_AP04 disabled -
ANHAM_AP02 disabled -
Press Enter to continue or <ctrl-z> to abort
AP Location
Total Number of AP Groups........................ 3
Site Name........................................ ANHAM8075
Site Description................................. ANHAM 8075 Location
WLAN ID Interface Network Admission Control Radio Policy
1 knowlogy_ogr Disabled None
6 knowlogy_ogr Disabled None
9 knowlogy_ogr Disabled None
7 knowlogy_ogr Disabled None
AP Name Slots AP Model Ethernet MAC Location Port Country Priority
Anham_AP03 2 AIR-LAP1142N-A-K9 70:81:05:88:15:b5 default location 1 US 1
ANHAM_AP01 2 AIR-LAP1142N-A-K9 70:81:05:b0:e4:62 Small Conference 1 US 1
ANHAM_AP04 2 AIR-LAP1131AG-A-K9 00:1d:45:86:e1:b8 Conference room 1 US 1
ANHAM_AP02 2 AIR-LAP1142N-A-K9 70:81:05:96:7a:49 Copy Room 1 US 1
Site Name........................................ Knowlogy_DC
--More or (q)uit current module or <ctrl-z> to abort
Site Description................................. DC Center Access points
WLAN ID Interface Network Admission Control Radio Policy
2 knowlogy_ogr Disabled None
4 knowlogy_ogr Disabled None
3 knowlogy_ogr Disabled None
AP Name Slots AP Model Ethernet MAC Location Port Country Priority
KNOWLOGY_DC01 2 AIR-LAP1131AG-A-K9 00:1d:45:86:ed:4e KNOWLOGY_DC_Serv 1 US 1
KNOWLOGY_DC02 2 AIR-LAP1131AG-A-K9 00:21:d8:36:c5:c4 KNOWLOGY_DC_Serv 1 US 1
Site Name........................................ OGR
Site Description................................. 1934 OGR Office
WLAN ID Interface Network Admission Control Radio Policy
1 knowlogy_ogr Disabled None
2 knowlogy_ogr Disabled None
4 knowlogy_ogr Disabled None
6 knowlogy_ogr Disabled None
--More or (q)uit current module or <ctrl-z> to abort
7 knowlogy_ogr Disabled None
9 knowlogy_ogr Disabled None
8 knowlogy_ogr Disabled None
AP Name Slots AP Model Ethernet MAC Location Port Country Priority
KN1252_AP01 2 AIR-LAP1252AG-A-K9 00:21:d8:ef:06:50 Knowlogy Confere 1 US 1
KN1252_AP02 2 AIR-LAP1252AG-A-K9 00:22:55:8e:2e:d4 Server Room Side 1 US 1
Site Name........................................ default-group
Site Description................................. <none>
WLAN ID Interface Network Admission Control Radio Policy
1 knowlogy_ogr Disabled None
2 knowlogy_ogr Disabled None
3 knowlogy_ogr Disabled None
4 knowlogy_ogr Disabled None
5 knowlogy_ogr Disabled None
6 knowlogy_ogr Disabled None
7 knowlogy_ogr Disabled None
8 knowlogy_ogr Disabled None
--More or (q)uit current module or <ctrl-z> to abort
9 knowlogy_ogr Disabled None
10 management Disabled None
AP Name Slots AP Model Ethernet MAC Location Port Country Priority
Press Enter to continue or <ctrl-z> to abort
AP Config
Cisco AP Identifier.............................. 6
Cisco AP Name.................................... KNOWLOGY_DC01
Country code..................................... US - United States
Regulatory Domain allowed by Country............. 802.11bg:-A 802.11a:-A
AP Country code.................................. US - United States
AP Regulatory Domain............................. -A
Switch Port Number .............................. 1
MAC Address...................................... 00:1d:45:86:ed:4e
IP Address Configuration......................... DHCP
IP Address....................................... 10.22.1.100
Gateway IP Addr.................................. 10.22.1.1
NAT External IP Address.......................... None
CAPWAP Path MTU.................................. 1485
Telnet State..................................... Disabled
Ssh State........................................ Disabled
Cisco AP Location................................ KNOWLOGY_DC_ServerRoom
Cisco AP Group Name.............................. Knowlogy_DC
Primary Cisco Switch Name........................ wireless.knowlogy.com
Primary Cisco Switch IP Address.................. 10.125.18.15
Secondary Cisco Switch Name......................
Secondary Cisco Switch IP Address................ Not Configured
--More or (q)uit current module or <ctrl-z> to abortIP Address.................. 10.125.18.15
Tertiary Cisco Switch Name.......................
Tertiary Cisco Switch IP Address................. Not Configured
Administrative State ............................ ADMIN_ENABLED
Operation State ................................. REGISTERED
Mirroring Mode .................................. Disabled
AP Mode ......................................... H-Reap
Public Safety ................................... Disabled
AP SubMode ...................................... Not Configured
Remote AP Debug ................................. Disabled
Logging trap severity level ..................... informational
Logging syslog facility ......................... kern
S/W Version .................................... 7.0.235.0
Boot Version ................................... 12.3.8.0
Mini IOS Version ................................ 3.0.51.0
Stats Reporting Period .......................... 180
LED State........................................ Enabled
PoE Pre-Standard Switch.......................... Disabled
PoE Power Injector MAC Addr...................... Disabled
Power Type/Mode.................................. Power injector / Normal mode
Number Of Slots.................................. 2
AP Model......................................... AIR-LAP1131AG-A-K9
AP Image......................................... C1130-K9W8-M
IOS Version...................................... 12.4(23c)JA5
--More or (q)uit current module or <ctrl-z> to abort
Reset Button..................................... Enabled
AP Serial Number................................. FTX1134T0QG
AP Certificate Type.............................. Manufacture Installed
H-REAP Vlan mode :............................... Enabled
Native ID :..................................... 22
WLAN 2 :........................................ 21
WLAN 4 :........................................ 25
WLAN 3 :........................................ 25
H-REAP Backup Auth Radius Servers :
Static Primary Radius Server.................... Disabled
Static Secondary Radius Server.................. Disabled
Group Primary Radius Server..................... Disabled
Group Secondary Radius Server................... Disabled
AP User Mode..................................... AUTOMATIC
AP User Name..................................... Not Configured
AP Dot1x User Mode............................... Not Configured
AP Dot1x User Name............................... Not Configured
Cisco AP system logging host..................... 255.255.255.255
AP Up Time....................................... 48 days, 20 h 19 m 18 s
AP LWAPP Up Time................................. 40 days, 13 h 58 m 18 s
Join Date and Time............................... Tue Sep 24 21:24:33 2013
Join Taken Time.................................. 0 days, 00 h 10 m 47 s
--More or (q)uit current module or <ctrl-z> to abort
Attributes for Slot 0
Radio Type................................... RADIO_TYPE_80211b
Administrative State ........................ ADMIN_ENABLED
Operation State ............................. UP
Radio Role .................................. ACCESS
CellId ...................................... 0
Station Configuration
Configuration ............................. AUTOMATIC
Number Of WLANs ........................... 3
Medium Occupancy Limit .................... 100
CFP Period ................................ 4
CFP MaxDuration ........................... 60
BSSID ..................................... 00:1d:71:09:8f:90
Operation Rate Set
1000 Kilo Bits........................... MANDATORY
2000 Kilo Bits........................... MANDATORY
5500 Kilo Bits........................... MANDATORY
11000 Kilo Bits.......................... MANDATORY
Beacon Period ............................. 100
Fragmentation Threshold ................... 2346
Multi Domain Capability Implemented ....... TRUE
--More or (q)uit current module or <ctrl-z> to abort
Multi Domain Capability Enabled ........... TRUE
Country String ............................ US
Multi Domain Capability
Configuration ............................. AUTOMATIC
First Chan Num ............................ 1
Number Of Channels ........................ 11
MAC Operation Parameters
Configuration ............................. AUTOMATIC
Fragmentation Threshold ................... 2346
Packet Retry Limit ........................ 64
Tx Power
Num Of Supported Power Levels ............. 8
Tx Power Level 1 .......................... 20 dBm
Tx Power Level 2 .......................... 17 dBm
Tx Power Level 3 .......................... 14 dBm
Tx Power Level 4 .......................... 11 dBm
Tx Power Level 5 .......................... 8 dBm
Tx Power Level 6 .......................... 5 dBm
Tx Power Level 7 .......................... 2 dBm
Tx Power Level 8 .......................... -1 dBm
--More or (q)uit current module or <ctrl-z> to abort
Tx Power Configuration .................... AUTOMATIC
Current Tx Power Level .................... 1
Phy DSSS parameters
Configuration ............................. AUTOMATIC
Current Channel ........................... 11
Extension Channel ......................... NONE
Channel Width.............................. 20 Mhz
Allowed Channel List....................... 1,2,3,4,5,6,7,8,9,10,11
Current CCA Mode .......................... 0
ED Threshold .............................. -50
Antenna Type............................... INTERNAL_ANTENNA
Internal Antenna Gain (in .5 dBi units).... 8
Diversity.................................. DIVERSITY_ENABLED
Performance Profile Parameters
Configuration ............................. AUTOMATIC
Interference threshold..................... 10 %
Noise threshold............................ -70 dBm
RF utilization threshold................... 80 %
Data-rate threshold........................ 1000000 bps
Client threshold........................... 12 clients
Coverage SNR threshold..................... 12 dB
--More or (q)uit current module or <ctrl-z> to abort
Coverage exception level................... 25 %
Client minimum exception level............. 3 clients
Rogue Containment Information
Containment Count............................ 0
CleanAir Management Information
CleanAir Capable......................... No
Cisco AP Identifier.............................. 6
Cisco AP Name.................................... KNOWLOGY_DC01
Country code..................................... US - United States
Regulatory Domain allowed by Country............. 802.11bg:-A 802.11a:-A
AP Country code.................................. US - United States
AP Regulatory Domain............................. -A
Switch Port Number .............................. 1
MAC Address...................................... 00:1d:45:86:ed:4e
IP Address Configuration......................... DHCP
IP Address....................................... 10.22.1.100
Gateway IP Addr.................................. 10.22.1.1
NAT External IP Address.......................... None
CAPWAP Path MTU.................................. 1485
Telnet State..................................... Disabled
Ssh State........................................ Disabled
--More or (q)uit current module or <ctrl-z> to abort
Cisco AP Location................................ KNOWLOGY_DC_ServerRoom
Cisco AP Group Name.............................. Knowlogy_DC
Primary Cisco Switch Name........................ wireless.knowlogy.com
Primary Cisco Switch Secondary Cisco Switch Name......................
Secondary Cisco Switch IP Address................ Not Configured
Tertiary Cisco Switch Name.......................
Tertiary Cisco Switch IP Address................. Not Configured
Administrative State ............................ ADMIN_ENABLED
Operation State ................................. REGISTERED
Mirroring Mode .................................. Disabled
AP Mode ......................................... H-Reap
Public Safety ................................... Disabled
AP SubMode ...................................... Not Configured
Remote AP Debug ................................. Disabled
Logging trap severity level ..................... informational
Logging syslog facility ......................... kern
S/W Version .................................... 7.0.235.0
Boot Version ................................... 12.3.8.0
Mini IOS Version ................................ 3.0.51.0
Stats Reporting Period .......................... 180
LED State........................................ Enabled
PoE Pre-Standard Switch.......................... Disabled
PoE Power Injector MAC Addr...................... Disabled
--More or (q)uit current module or <ctrl-z> to abort
Power Type/Mode.................................. Power injector / Normal mode
Number Of Slots.................................. 2
AP Model......................................... AIR-LAP1131AG-A-K9
AP Image......................................... C1130-K9W8-M
IOS Version...................................... 12.4(23c)JA5
Reset Button..................................... Enabled
AP Serial Number................................. FTX1134T0QG
AP Certificate Type.............................. Manufacture Installed
H-REAP Vlan mode :............................... Enabled
Native ID :..................................... 22
WLAN 2 :........................................ 21
WLAN 4 :........................................ 25
WLAN 3 :........................................ 25
H-REAP Backup Auth Radius Servers :
Static Primary Radius Server.................... Disabled
Static Secondary Radius Server.................. Disabled
Group Primary Radius Server..................... Disabled
Group Secondary Radius Server................... Disabled
AP User Mode..................................... AUTOMATIC
AP User Name..................................... Not Configured
AP Dot1x User Mode............................... Not Configured
AP Dot1x User Name............................... Not Configured
Cisco AP system logging host..................... 255.255.255.255
--More or (q)uit current module or <ctrl-z> to abort
AP Up Time....................................... 48 days, 20 h 19 m 18 s
AP LWAPP Up Time................................. 40 days, 13 h 58 m 18 s
Join Date and Time............................... Tue Sep 24 21:24:33 2013
Join Taken Time.................................. 0 days, 00 h 10 m 47 s
Attributes for Slot 1
Radio Type................................... RADIO_TYPE_80211a
Radio Subband................................ RADIO_SUBBAND_ALL
Administrative State ........................ ADMIN_ENABLED
Operation State ............................. UP
Radio Role .................................. ACCESS
CellId ...................................... 0
Station Configuration
Configuration ............................. AUTOMATIC
Number Of WLANs ........................... 3
Medium Occupancy Limit .................... 100
CFP Period ................................ 4
CFP MaxDuration ........................... 60
BSSID ..................................... 00:1d:71:09:8f:90
Operation Rate Set
6000 Kilo Bits........................... MANDATORY
--More or (q)uit current module or <ctrl-z> to abort
9000 Kilo Bits........................... SUPPORTED
12000 Kilo Bits.......................... MANDATORY
18000 Kilo Bits.......................... SUPPORTED
24000 Kilo Bits.......................... MANDATORY
36000 Kilo Bits.......................... SUPPORTED
48000 Kilo Bits.......................... SUPPORTED
54000 Kilo Bits.......................... SUPPORTED
Beacon Period ............................. 100
Fragmentation Threshold ................... 2346
Multi Domain Capability Implemented ....... TRUE
Multi Domain Capability Enabled ........... TRUE
Country String ............................ US
Multi Domain Capability
Configuration ............................. AUTOMATIC
First Chan Num ............................ 36
Number Of Channels ........................ 20
MAC Operation Parameters
Configuration ............................. AUTOMATIC
Fragmentation Threshold ................... 2346
Packet Retry Limit ........................ 64
--More or (q)uit current module or <ctrl-z> to abort
Tx Power
Num Of Supported Power Levels ............. 7
Tx Power Level 1 .......................... 15 dBm
Tx Power Level 2 .......................... 14 dBm
Tx Power Level 3 .......................... 11 dBm
Tx Power Level 4 .......................... 8 dBm
Tx Power Level 5 .......................... 5 dBm
Tx Power Level 6 .......................... 2 dBm
Tx Power Level 7 .......................... -1 dBm
Tx Power Configuration .................... AUTOMATIC
Current Tx Power Level .................... 1
Phy OFDM parameters
Configuration ............................. AUTOMATIC
Current Channel ........................... 44
Extension Channel ......................... NONE
Channel Width.............................. 20 Mhz
Allowed Channel List....................... 36,40,44,48,52,56,60,64,100,
......................................... 104,108,112,116,132,136,140,
......................................... 149,153,157,161
TI Threshold .............................. -50
Antenna Type............................... INTERNAL_ANTENNA
Internal Antenna Gain (in .5 dBi units).... 8
--More or (q)uit current module or <ctrl-z> to abort
Diversity.................................. DIVERSITY_ENABLED
Performance Profile Parameters
Configuration ............................. AUTOMATIC
Interference threshold..................... 10 %
Noise threshold............................ -70 dBm
RF utilization threshold................... 80 %
Data-rate threshold........................ 1000000 bps
Client threshold........................... 12 clients
Coverage SNR threshold..................... 16 dB
Coverage exception level................... 25 %
Client minimum exception level............. 3 clients
Rogue Containment Information
Containment Count............................ 0
CleanAir Management Information
CleanAir Capable......................... No
Press Enter to continue or <ctrl-z> to abort
Cisco AP Identifier.............................. 3
Cisco AP Name.................................... KNOWLOGY_DC02
Country code..................................... US - United States
Regulatory Domain allowed by Country............. 802.11bg:-A 802.11a:-A
AP Country code.................................. US - United States
AP Regulatory Domain............................. -A
Switch Port Number .............................. 1
MAC Address...................................... 00:21:d8:36:c5:c4
IP Address Configuration......................... DHCP
IP Address....................................... 10.22.1.101
Gateway IP Addr.................................. 10.22.1.1
NAT External IP Address.......................... None
CAPWAP Path MTU.................................. 1485
Telnet State..................................... Disabled
Ssh State........................................ Disabled
Cisco AP Location................................ KNOWLOGY_DC_ServerRoom
Cisco AP Group Name.............................. Knowlogy_DC
Primary Cisco Switch Name........................
Primary Cisco Switch IP Address.................. Not Configured
Secondary Cisco Switch Name......................
Secondary Cisco Switch IP Address................ Not Configured
Tertiary Cisco Switch Name.......................
--More or (q)uit current module or <ctrl-z> to abort
Tertiary Cisco Switch IP Address................. Not Configured
Administrative State ............................ ADMIN_ENABLED
Operation State ................................. REGISTERED
Mirroring Mode .................................. Disabled
AP Mode ......................................... H-Reap
Public Safety ................................... Disabled
AP SubMode ...................................... Not Configured
Remote AP Debug ................................. Disabled
Logging trap severity level ..................... informational
Logging syslog facility ......................... kern
S/W Version .................................... 7.0.235.0
Boot Version ................................... 12.3.8.0
Mini IOS Version ................................ 3.0.51.0
Stats Reporting Period .......................... 180
LED State........................................ Enabled
PoE Pre-Standard Switch.......................... Enabled
PoE Power Injector MAC Addr...................... Disabled
Power Type/Mode.................................. Power injector / Normal mode
Number Of Slots.................................. 2
AP Model......................................... AIR-LAP1131AG-A-K9
AP Image......................................... C1130-K9W8-M
IOS Version...................................... 12.4(23c)JA5
Reset Button..................................... Enabled
--More or (q)uit current module or <ctrl-z> to abort
AP Serial Number................................. FTX1230T24F
AP Certificate Type.............................. Manufacture Installed
H-REAP Vlan mode :............................... Enabled
Native ID :..................................... 22
WLAN 2 :........................................ 21
WLAN 4 :........................................ 25
WLAN 3 :........................................ 25
H-REAP Backup Auth Radius Servers :
Static Primary Radius Server.................... Disabled
Static Secondary Radius Server.................. Disabled
Group Primary Radius Server..................... Disabled
Group Secondary Radius Server................... Disabled
AP User Mode..................................... AUTOMATIC
AP User Name..................................... Not Configured
AP Dot1x User Mode............................... Not Configured
AP Dot1x User Name............................... Not Configured
Cisco AP system logging host..................... 255.255.255.255
AP Up Time....................................... 48 days, 20 h 24 m 41 s
AP LWAPP Up Time................................. 40 days, 13 h 58 m 18 s
Join Date and Time............................... Tue Sep 24 21:24:35 2013
Join Taken Time.................................. 0 days, 00 h 10 m 48 s
--More or (q)uit current module or <ctrl-z> to abort
Attributes for Slot 0
Radio Type................................... RADIO_TYPE_80211b
Administrative State ........................ ADMIN_ENABLED
Operation State ............................. UP
Radio Role .................................. ACCESS
CellId ...................................... 0
Station Configuration
Configuration ............................. AUTOMATIC
Number Of WLANs ........................... 3
Medium Occupancy Limit .................... 100
CFP Period ................................ 4
CFP MaxDuration ........................... 60
BSSID ..................................... 00:22:55:a5:0c:30
Operation Rate Set
1000 Kilo Bits........................... MANDATORY
2000 Kilo Bits........................... MANDATORY
5500 Kilo Bits........................... MANDATORY
11000 Kilo Bits.......................... MANDATORY
Beacon Period ............................. 100
Fragmentation Threshold ................... 2346
Multi Domain Capability Implemented ....... TRUE
Multi Domain Capability Enabled ........... TRUE
--More or (q)uit current module or <ctrl-z> to abort
Country String ............................ US
Multi Domain Capability
Configuration ............................. AUTOMATIC
First Chan Num ............................ 1
Number Of Channels ........................ 11
MAC Operation Parameters
Configuration ............................. AUTOMATIC
Fragmentation Threshold ................... 2346
Packet Retry Limit ........................ 64
Tx Power
Num Of Supported Power Levels ............. 8
Tx Power Level 1 .......................... 20 dBm
Tx Power Level 2 .......................... 17 dBm
Tx Power Level 3 .......................... 14 dBm
Tx Power Level 4 .......................... 11 dBm
Tx Power Level 5 .......................... 8 dBm
Tx Power Level 6 .......................... 5 dBm
Tx Power Level 7 .......................... 2 dBm
Tx Power Level 8 .......................... -1 dBm
Tx Power Configuration .................... AUTOMATIC
--More or (q)uit current module or <ctrl-z> to abort
Current Tx Power Level .................... 1
Phy DSSS parameters
Configuration ............................. AUTOMATIC
Current Channel ........................... 1
Extension Channel ......................... NONE
Channel Width.............................. 20 Mhz
Allowed Channel List....................... 1,2,3,4,5,6,7,8,9,10,11
Current CCA Mode .......................... 0
ED Threshold .............................. -50
Antenna Type............................... INTERNAL_ANTENNA
Internal Antenna Gain (in .5 dBi units).... 8
Diversity.................................. DIVERSITY_ENABLED
Performance Profile Parameters
Configuration ............................. AUTOMATIC
Interference threshold..................... 10 %
Noise threshold............................ -70 dBm
RF utilization threshold................... 80 %
Data-rate threshold........................ 1000000 bps
Client threshold........................... 12 clients
Coverage SNR threshold..................... 12 dB
Coverage exception level................... 25 %
--More or (q)uit current module or <ctrl-z> to abort
Client minimum exception level............. 3 clients
Rogue Containment Information
Containment Count............................ 0
CleanAir Management Information
CleanAir Capable......................... No
Cisco AP Identifier.............................. 3
Cisco AP Name.................................... KNOWLOGY_DC02
Country code..................................... US - United States
Regulatory Domain allowed by Country............. 802.11bg:-A 802.11a:-A
AP Country code.................................. US - United States
AP Regulatory Domain............................. -A
Switch Port Number .............................. 1
MAC Address...................................... 00:21:d8:36:c5:c4
IP Address Configuration......................... DHCP
IP Address....................................... 10.22.1.101
Gateway IP Addr.................................. 10.22.1.1
NAT External IP Address.......................... None
CAPWAP Path MTU.................................. 1485
Telnet State..................................... Disabled
Ssh State........................................ Disabled
Cisco AP Location................................ KNOWLOGY_DC_ServerRoom
--More or (q)uit current module or <ctrl-z> to abort
Cisco AP Group Name.............................. Knowlogy_DC
Primary Cisco Switch Name........................
Primary Cisco Switch IP Address.................. Not Configured
Secondary Cisco Switch Name......................
Secondary Cisco Switch IP Address................ Not Configured
Tertiary Cisco Switch Name.......................
Tertiary Cisco Switch IP Address................. Not Configured
Administrative State ............................ ADMIN_ENABLED
Operation State ................................. REGISTERED
Mirroring Mode .................................. Disabled
AP Mode ......................................... H-Reap
Public Safety ................................... Disabled
AP SubMode ...................................... Not Configured
Remote AP Debug ................................. Disabled
Logging trap severity level ..................... informational
Logging syslog facility ......................... kern
S/W Version .................................... 7.0.235.0
Boot Version ................................... 12.3.8.0
Mini IOS Version ................................ 3.0.51.0
Stats Reporting Period .......................... 180
LED State........................................ Enabled
PoE Pre-Standard Switch.......................... Enabled
PoE Power Injector MAC Addr...................... Disabled
--More or (q)uit current module or <ctrl-z> to abort
Power Type/Mode.................................. Power injector / Normal mode
Number Of Slots.................................. 2
AP Model......................................... AIR-LAP1131AG-A-K9
AP Image......................................... C1130-K9W8-M
IOS Version...................................... 12.4(23c)JA5
Reset Button..................................... Enabled
AP Serial Number................................. FTX1230T24F
AP Certificate Type.............................. Manufacture Installed
H-REAP Vlan mode :............................... Enabled
Native ID :..................................... 22
WLAN 2 :........................................ 21
WLAN 4 :........................................ 25
WLAN 3 :........................................ 25
H-REAP Backup Auth Radius Servers :
Static Primary Radius Server.................... Disabled
Static Secondary Radius Server.................. Disabled
Group Primary Radius Server..................... Disabled
Group Secondary Radius Server................... Disabled
AP User Mode..................................... AUTOMATIC
AP User Name..................................... Not Configured
AP Dot1x User Mode............................... Not Configured
AP Dot1x User Name............................... Not Configured
Cisco AP system logging host..................... 255.255.255.255
--More or (q)uit current module or <ctrl-z> to abort
AP Up Time....................................... 48 days, 20 h 24 m 41 s
AP LWAPP Up Time................................. 40 days, 13 h 58 m 18 s
Join Date and Time............................... Tue Sep 24 21:24:35 2013
Join Taken Time.................................. 0 days, 00 h 10 m 48 s
Attributes for Slot 1
Radio Type................................... RADIO_TYPE_80211a
Radio Subband................................ RADIO_SUBBAND_ALL
Administrative State ........................ ADMIN_ENABLED
Operation State ............................. UP
Radio Role .................................. ACCESS
CellId ...................................... 0
Station Configuration
Configuration ............................. AUTOMATIC
Number Of WLANs ........................... 3
Medium Occupancy Limit .................... 100
CFP Period ................................ 4
CFP MaxDuration ........................... 60
BSSID ..................................... 00:22:55:a5:0c:30
Operation Rate Set
6000 Kilo Bits........................... MANDATORY
--More or (q)uit current module or <ctrl-z> to abort
9000 Kilo Bits........................... SUPPORTED
12000 Kilo Bits.......................... MANDATORY
18000 Kilo Bits.......................... SUPPORTED
24000 Kilo Bits.......................... MANDATORY
36000 Kilo Bits.......................... SUPPORTED
48000 Kilo Bits.......................... SUPPORTED
54000 Kilo Bits.......................... SUPPORTED
Beacon Period ............................. 100
Fragmentation Threshold ................... 2346
Multi Domain Capability Implemented ....... TRUE
Multi Domain Capability Enabled ........... TRUE
Country String ............................ US
Multi Domain Capability
Configuration ............................. AUTOMATIC
First Chan Num ............................ 36
Number Of Channels ........................ 20
MAC Operation Parameters
Configuration ............................. AUTOMATIC
Fragmentation Threshold ................... 2346
Packet Retry Limit ........................ 64
--More or (q)uit current module or <ctrl-z> to abort
Tx Power
Num Of Supported Power Levels ............. 7
Tx Power Level 1 .......................... 15 dBm
Tx Power Level 2 .......................... 14 dBm
Tx Power Level 3 .......................... 11 dBm
Tx Power Level 4 .......................... 8 dBm
Tx Power Level 5 .......................... 5 dBm
Tx Power Level 6 .......................... 2 dBm
Tx Power Level 7 .......................... -1 dBm
Tx Power Configuration .................... AUTOMATIC
Current Tx Power Level .................... 1
Phy OFDM parameters
Configuration ............................. AUTOMATIC
Current Channel ........................... 36
Extension Channel ......................... NONE
Channel Width.............................. 20 Mhz
Allowed Channel List....................... 36,40,44,48,52,56,60,64,100,
......................................... 104,108,112,116,132,136,140,
......................................... 149,153,157,161
TI Threshold .............................. -50
Antenna Type............................... INTERNAL_ANTENNA
Internal Antenna Gain (in .5 dBi units).... 8
--More or (q)uit current module or <ctrl-z> to abort
Diversity.................................. DIVERSITY_ENABLED
Performance Profile Parameters
Configuration ............................. AUTOMATIC
Interference threshold..................... 10 %
Noise threshold............................ -70 dBm
RF utilization threshold................... 80 %
Data-rate threshold........................ 1000000 bps
Client threshold........................... 12 clients
Coverage SNR threshold..................... 16 dB
Coverage exception level................... 25 %
Client minimum exception level............. 3 clients
Rogue Containment Information
Containment Count............................ 0
CleanAir Management Information
CleanAir Capable......................... No
Press Enter to continue or <ctrl-z> to abort
Cisco AP Identifier.............................. 5
Cisco AP Name.................................... KN1252_AP01
Country code..................................... US - United States
Regulatory Domain allowed by Country............. 802.11bg:-A 802.11a:-A
AP Country code.................................. US - United States
AP Regulatory Domain............................. -A
Switch Port Number .............................. 1
MAC Address...................................... 00:21:d8:ef:06:50
IP Address Configuration......................... DHCP
IP Address....................................... 10.125.18.101
IP NetMask....................................... 255.255.255.0
Gateway IP Addr.................................. 10.125.18.1
NAT External IP Address.......................... None
CAPWAP Path MTU.................................. 1485
Telnet State..................................... Enabled
Ssh State........................................ Disabled
Cisco AP Location................................ Knowlogy Conference Rooms Side
Cisco AP Group Name.............................. OGR
Primary Cisco Switch Name........................
Primary Cisco Switch IP Address.................. Not Configured
Secondary Cisco Switch Name......................
Secondary Cisco Switch IP Address................ Not Configured
--More or (q)uit current module or <ctrl-z> to abort
Tertiary Cisco Switch Name.......................
Tertiary Cisco Switch IP Address................. Not Configured
Administrative State ............................ ADMIN_ENABLED
Operation State ................................. REGISTERED
Mirroring Mode .................................. Disabled
AP Mode ......................................... H-Reap
Public Safety ................................... Disabled
AP SubMode ...................................... Not Configured
Remote AP Debug ................................. Disabled
Logging trap severity level ..................... informational
Logging syslog facility ......................... kern
S/W Version .................................... 7.0.235.0
Boot Version ................................... 12.4.10.0
Mini IOS Version ................................ 3.0.51.0
Stats Reporting Period .......................... 180
LED State........................................ Enabled
PoE Pre-Standard Switch.......................... Disabled
PoE Power Injector MAC Addr...................... Disabled
Power Type/Mode.................................. PoE/Medium Power (15.4 W)
Number Of Slots.................................. 2
AP Model......................................... AIR-LAP1252AG-A-K9
AP Image......................................... C1250-K9W8-M
IOS Version...................................... 12.4(23c)JA5
--More or (q)uit current module or <ctrl-z> to abort
Reset Button..................................... Enabled
AP Serial Number................................. FTX122990L5
AP Certificate Type.............................. Manufacture Installed
H-REAP Vlan mode :............................... Enabled
Native ID :..................................... 118
WLAN 1 :........................................ 111
WLAN 2 :........................................ 111
WLAN 4 :........................................ 112
WLAN 6 :........................................ 112
WLAN 7 :........................................ 111
WLAN 9 :........................................ 112
WLAN 8 :........................................ 112
H-REAP Backup Auth Radius Servers :
Static Primary Radius Server.................... Disabled
Static Secondary Radius Server.................. Disabled
Group Primary Radius Server..................... Disabled
Group Secondary Radius Server................... Disabled
AP User Mode..................................... AUTOMATIC
AP User Name..................................... Not Configured
AP Dot1x User Mode............................... Not Configured
AP Dot1x User Name............................... Not Configured
Cisco AP system logging host..................... 255.255.255.255
AP Up Time....................................... 26 days, 00 h 24 m 39 s
--More or (q)uit current module or <ctrl-z> to abort
AP LWAPP Up Time................................. 26 days, 00 h 23 m 48 s
Join Date and Time............................... Wed Oct 9 10:59:07 2013
Join Taken Time.................................. 0 days, 00 h 00 m 50 s
Attributes for Slot 0
Radio Type................................... RADIO_TYPE_80211n-2.4
Administrative State ........................ ADMIN_ENABLED
Operation State ............................. UP
Radio Role .................................. ACCESS
CellId ...................................... 0
Station Configuration
Configuration ............................. AUTOMATIC
Number Of WLANs ........................... 7
Medium Occupancy Limit .................... 100
CFP Period ................................ 4
CFP MaxDuration ........................... 60
BSSID ..................................... 00:22:55:df:a5:90
Operation Rate Set
1000 Kilo Bits........................... MANDATORY
2000 Kilo Bits........................... MANDATORY
5500 Kilo Bits........................... MANDATORY
--More or (q)uit current module or <ctrl-z> to abort
11000 Kilo Bits.......................... MANDATORY
MCS Set
MCS 0.................................... SUPPORTED
MCS 1.................................... SUPPORTED
MCS 2.................................... SUPPORTED
MCS 3.................................... SUPPORTED
MCS 4.................................... SUPPORTED
MCS 5.................................... SUPPORTED
MCS 6.................................... SUPPORTED
MCS 7.................................... SUPPORTED
MCS 8.................................... SUPPORTED
MCS 9.................................... SUPPORTED
MCS 10................................... SUPPORTED
MCS 11................................... SUPPORTED
MCS 12................................... SUPPORTED
MCS 13................................... SUPPORTED
MCS 14................................... SUPPORTED
MCS 15................................... SUPPORTED
Beacon Period ............................. 100
Fragmentation Threshold ................... 2346
Multi Domain Capability Implemented ....... TRUE
Multi Domain Capability Enabled ........... TRUE
Country String ............................ US
--More or (q)uit current module or <ctrl-z> to abort
Multi Domain Capability
Configuration ............................. AUTOMATIC
First Chan Num ............................ 1
Number Of Channels ........................ 11
MAC Operation Parameters
Configuration ............................. AUTOMATIC
Fragmentation Threshold ................... 2346
Packet Retry Limit ........................ 64
Tx Power
Num Of Supported Power Levels ............. 8
Tx Power Level 1 .......................... 20 dBm
Tx Power Level 2 .......................... 17 dBm
Tx Power Level 3 .......................... 14 dBm
Tx Power Level 4 ..........Well you need to understand the behavior of h-reap or what it's called now, FlexConnect. In this mode, the clients are still remembers on the WLC until the session timer/idle timer expires. So switching between SSID's in h-reap will not be the same when switching when the AP's are in local mode.
Take a look at the client when connected in FlexConnect in the WLC GUI monitor tab. Thus will show you what ssid and vlan the client is on. Now switch to a different ssid and compare this. It's probably the same because the client has not timed out. Now go back to the other ssid and look again. Now on the WLC, remove or delete the client and then switch to the other ssid at the same time. Or switch SSID's and then remove the client. The client will join the new ssid and in the monitor tab, you should see the info.
There is no need to have clients have multiple SSID's unless your testing. Devices should only have one ssid profile configured to eliminate any connectivity issues from the device wanting to switch SSID's.
Sent from Cisco Technical Support iPhone App -
Ask the Expert: One Management with Prime Infrastructure 1.2
With Tejas Shah
Welcome to the Cisco Support Community Ask the Expert conversation. This is an opportunity to learn and ask questions from Cisco expert Tejas Shah on One Management with Prime Infrastructure 1.2 Combining the wireless functionality of Cisco Prime Network Control System (NCS) with the wired functionality of Cisco Prime LAN Management Solution (LMS), Cisco Prime Infrastructure simplifies and automates many of the day-to-day tasks associated with maintaining and managing the end-to-end network infrastructure from a single pane of glass. The new converged solution delivers all of the existing wireless capabilities for RF management, user access visibility, reporting, and troubleshooting along with wired lifecycle functions such as discovery, inventory, configuration and image management, automated deployment, compliance reporting, integrated best practices, and reporting.
Tejas Shah is a senior technical marketing engineer for Cisco Prime Infrastructure and Collaboration products. He has deployed Cisco Prime Collaboration Manager at various customer sites to help customers monitor and troubleshoot their video infrastructure. In addition, he is part of the Network Operations Center team at Cisco Live events for six years. Shah joined Cisco in 1995 and was in the Technical Assistance Center team supporting various network management system products for more than six years.
Remember to use the rating system to let Tejas know if you have received an adequate response.
Tejas might not be able to answer each question due to the volume expected during this event. Remember that you can continue the conversation on the Wireless Mobility sub-community discussion forum shortly after the event. This event lasts through Sept 21, 2012. Visit this forum often to view responses to your questions and the questions of other community members.Raun, please see my responses inline:
Can you go over the licensing method with Prime Infrastructure 1.2 please?
Raun, you can check out the following link for ordering guide at
http://www.cisco.com/en/US/products/ps12239/products_data_sheets_list.html
I currently have NCS and do NOT currently have LMS. I know I can move to Prime Infrastructure through Cisco Product Upgrade Tool. However, what I am confused about is do I still have to buy LMS to have LMS functionality in Prime Infrastructure 1.2?
==> Not at all. The converged product will give you basic management capability for routers and switches that LMS provided in this release. Feature/Functionality will keep on growing with upcoming releases.
If not, do the licenses I transfer into Prime Infrastructure 1.2 from NCS also work for devices to work under LMS?
==> Licensing is different than NCS or LMS. You don't have to transfer the license. Each install of Prime Infrastructure will have a unique UID string on which the licenses are based. A new license will be applied to the product.
Mean, can my currently 350 licenses be used for AP's as in NCS and routers in the LMS portion of Prime Infrastructure 1.2?
==> I would recommend getting a total count of your wired and wireless devices and match the right SKU based on that.
Hope this helps.. Let me know if you have any further questions,
Tejas -
WLC 5508 with LAP-1142n - Several Errors
Hello all,
I had installed a WLC 5508 with 7 LAP 1142n and 2 converted AP 1131abg.
I am seeing some errors relating 2 issues.
1st- One particular AP 1142 is disassociating and reseting the radios.
/* Style Definitions */
table.MsoNormalTable
{mso-style-name:"Table Normal";
mso-tstyle-rowband-size:0;
mso-tstyle-colband-size:0;
mso-style-noshow:yes;
mso-style-priority:99;
mso-style-qformat:yes;
mso-style-parent:"";
mso-padding-alt:0cm 5.4pt 0cm 5.4pt;
mso-para-margin:0cm;
mso-para-margin-bottom:.0001pt;
mso-pagination:widow-orphan;
font-size:10.0pt;
font-family:"Times New Roman","serif";}
Thu Oct 28 11:50:49 2010
AP's Interface:0(802.11b) Operation State Up: Base Radio MAC:e8:04:62:23:ac:e0 Cause=Radio interface reset. Status:NA
Thu Oct 28 11:50:49 2010
AP's Interface:0(802.11b) Operation State Down: Base Radio MAC:e8:04:62:23:ac:e0 Cause=Radio interface reset. Status:NA
Thu Oct 28 11:50:49 2010
AP's Interface:1(802.11a) Operation State Up: Base Radio MAC:e8:04:62:23:ac:e0 Cause=Radio interface reset. Status:NA
Thu Oct 28 11:50:49 2010
AP's Interface:1(802.11a) Operation State Down: Base Radio MAC:e8:04:62:23:ac:e0 Cause=Radio interface reset. Status:NA
Thu Oct 28 11:50:46 2010
AP's Interface:1(802.11a) Operation State Up: Base Radio MAC:e8:04:62:23:ac:e0 Cause=Radio reset due to Init. Status:NA
Thu Oct 28 11:50:46 2010
AP's Interface:0(802.11b) Operation State Up: Base Radio MAC:e8:04:62:23:ac:e0 Cause=Radio reset due to Init. Status:NA
Thu Oct 28 11:50:46 2010
AP 'AP3', MAC: e8:04:62:23:ac:e0 disassociated previously due to AP Reset. Uptime: 1 days, 10 h 24 m 23 s . Last reset reason: operator changed 11g mode.
Thu Oct 28 11:50:35 2010
AP Disassociated. Base Radio MAC:e8:04:62:23:ac:e0
Thu Oct 28 11:50:35 2010
AP's Interface:1(802.11a) Operation State Down: Base Radio MAC:e8:04:62:23:ac:e0 Cause=New Discovery Status:NA
Thu Oct 28 11:50:35 2010
AP's Interface:0(802.11b) Operation State Down: Base Radio MAC:e8:04:62:23:ac:e0 Cause=New Discovery Status:NA
I had some search, and the new discovery cause, might be that the AP didnt know what WLC do associate, in a multi-controller environment. This is not the case. I only have one WLC in the same management vlan.
2st-The Radius server is beeing related in the logs as been deactivated. I raise the server time-out on Radius configuration option, but it still continues to do it.
/* Style Definitions */
table.MsoNormalTable
{mso-style-name:"Table Normal";
mso-tstyle-rowband-size:0;
mso-tstyle-colband-size:0;
mso-style-noshow:yes;
mso-style-priority:99;
mso-style-qformat:yes;
mso-style-parent:"";
mso-padding-alt:0cm 5.4pt 0cm 5.4pt;
mso-para-margin:0cm;
mso-para-margin-bottom:.0001pt;
mso-pagination:widow-orphan;
font-size:10.0pt;
font-family:"Times New Roman","serif";}
Thu Oct 28 10:24:41 2010
RADIUS server 10.67.128.36:1812 deactivated in global list
Thu Oct 28 10:24:41 2010
RADIUS server 10.67.128.36:1812 failed to respond to request (ID 172) for client e8:06:88:51:c0:2b / user 'unknown'
Is this meaning the WLC stop sending request to the Radius Server ? We dont have BackUp Radius.
As far as i know, its always the same mac-address client that is associated to that error, maybe a iphone.
I had so many clients in that SSID and they are all working good.
The Radius server is a NPS from windows Server 2008
/* Style Definitions */
table.MsoNormalTable
{mso-style-name:"Table Normal";
mso-tstyle-rowband-size:0;
mso-tstyle-colband-size:0;
mso-style-noshow:yes;
mso-style-priority:99;
mso-style-qformat:yes;
mso-style-parent:"";
mso-padding-alt:0cm 5.4pt 0cm 5.4pt;
mso-para-margin:0cm;
mso-para-margin-bottom:.0001pt;
mso-pagination:widow-orphan;
font-size:10.0pt;
font-family:"Times New Roman","serif";}
, and the client says that the medium response time is 0,02 sec, so im wondering why the controller is not getting response from Radius for a particular client?! My client also says, that didnt found any log related to that mac-address client ... what is weird...
WLC with last software available 7.0.164
Hope some one help me here.
Best Regards,
Bruno PetrónioThanks Scott,
I understand what you are mentioning, and i really didnt do it yet.
I realize that the primary controller was not configured on the
/* Style Definitions */
table.MsoNormalTable
{mso-style-name:"Table Normal";
mso-tstyle-rowband-size:0;
mso-tstyle-colband-size:0;
mso-style-noshow:yes;
mso-style-priority:99;
mso-style-qformat:yes;
mso-style-parent:"";
mso-padding-alt:0cm 5.4pt 0cm 5.4pt;
mso-para-margin:0cm;
mso-para-margin-bottom:.0001pt;
mso-pagination:widow-orphan;
font-size:10.0pt;
font-family:"Times New Roman","serif";}
Wireless –> All APs –> High Availability tab, and did it only to the AP that is taking this beahviour.
Is this mandatory for a 1 controller only ?
No mather what the manual say, after that the AP is rebooting 2 mins in 2 mins... with the same kind of messages.
The interface on the switch is getting a few input errors and the same numbers of crc... but are so few...
Next step ... i will change it to another one's place/pathing cable.
Regarding the Radius messages... any ideas ?
I'm already on 30 sec's of server timeout.
Best Regards,
Bruno Petrónio -
Deployment of WLC-5508 with 2702i-D have performance issue.
Hi Team,
We have centrally deployed WLC-5508 with 50 AP licence along with HA scenario. we have 3 locations.
1- HQ. have 26 AP with POWINJ5.
2- Branch location A- 8 AP with POWINJ5.
3. Branch location B have 8 AP with POWINJ4.
my exception is to achieve that single SSID with dynamic VLAN from group police (NPS). MY HO have 26 AP and those are working in local mode.
and branches are connected through flexconnect mode. and all are working with different-2 NPS.
Now i am facing a problem with this deployment are following.
1- branch A have performance issue.
2- HQ have performance issue.
3- i don't want to go with dedicated NPS for every location.
In order to achieve this deployment i want only single SSID with primary and secondary NPS at my HQ with dynamic VLAN for respective departmental users vlans..
above is my problem and concern. otherwise i am successfully achieving this solution with dedicated NPS with single group policy. but when i am going forward to achieve my expectation that time i am facing authentication issue at my HQ and sometimes am not able to get proper VLAN IPs. at my HQ.
kindly help me in that to understand where I am doing wrong things to achieve my expectation.
Thanks.
NalinI am facing 2 different problems.
1st issue- in existing setup we have throughput issue. (while downloading or uploading any data from the internet or Intranet, that time wireless clients are facing slowness of the Speed. and same time when i am trying from LAN i am not facing any issue)
2nd Issue- I want to achieve only single SSID with primary and secondary NPS (AD group is bind with vlan Attributes) with dynamic VLAN for respective departmental users.
for Issue no 2 i have created SSID to achieve the single ssid parameter for every location. in order to achieve i have change all access points mode local to Flexconnect mode after that i have created AP groups location wise and then create flexconnect Groups where i have mapped all the vlan through AAA VLAN-ACL mapping. created interface group and mapped all the vlans in that group.
for more understanding please go through the below mentioned CLI view.
Cisco Controller) >show wlan apgroups
Total Number of AP Groups........................ 4
Site Name........................................ GURGAON-AP-GROUP
Site Description................................. GURGAON-AP-GROUP
Venue Group Code................................. Unspecified
Venue Type Code.................................. Unspecified
NAS-identifier................................... Fractal-WLC1
Client Traffic QinQ Enable....................... FALSE
DHCPv4 QinQ Enable............................... FALSE
AP Operating Class............................... Not-configured
Capwap Prefer Mode............................... Not-configured
RF Profile
2.4 GHz band..................................... <none>
5 GHz band....................................... <none>
WLAN ID Interface Network Admission Control Radio Pol icy
3 gurgaon-interface Disabled None
--More-- or (q)uit
4 gurgaon-guest Disabled None
*AP3600 with 802.11ac Module will only advertise first 8 WLANs on 5GHz radios.
AP Name Slots AP Model Ethernet MAC Location Port Country Priority
GUR-AP-01 2 AIR-CAP2702I-D-K9 f4:4e:05:78:ae:e4 default location 1 IN 1
GUR-AP-05 2 AIR-CAP2702I-D-K9 f4:4e:05:80:b5:18 default location 1 IN 1
GUR-AP-03 2 AIR-CAP2702I-D-K9 bc:16:65:13:71:00 default location 1 IN 1
GUR-AP-07 2 AIR-CAP2702I-D-K9 f4:4e:05:80:b3:f8 default location 1 IN 1
GUR-AP-06 2 AIR-CAP2702I-D-K9 f4:4e:05:80:b3:e0 default location 1 IN 1
GUR-AP-08 2 AIR-CAP2702I-D-K9 f4:4e:05:45:78:98 default location 1 IN 1
GUR-AP-02 2 AIR-CAP2702I-D-K9 f4:4e:05:80:b3:2c default location 1 IN 1
GUR-AP-04 2 AIR-CAP2702I-D-K9 f4:4e:05:78:ae:64 default location 1 IN 1
GUR-AP-09 2 AIR-CAP2702I-D-K9 f4:4e:05:80:b4:44 default location 1 IN 1
Site Name........................................ MUMBAI-AP-GROUP
Site Description................................. MUMBAI-AP-GROUP
Venue Group Code................................. Unspecified
Venue Type Code.................................. Unspecified
--More-- or (q)uit
NAS-identifier................................... Fractal-WLC1
Client Traffic QinQ Enable....................... FALSE
DHCPv4 QinQ Enable............................... FALSE
AP Operating Class............................... Not-configured
Capwap Prefer Mode............................... Not-configured
RF Profile
2.4 GHz band..................................... <none>
5 GHz band....................................... <none>
WLAN ID Interface Network Admission Control Radio Policy
1 group for mumbai Disabled None
2 guest wifi Disabled None
*AP3600 with 802.11ac Module will only advertise first 8 WLANs on 5GHz radios.
AP Name Slots AP Model Ethernet MAC Location Port Country Priority
FAL-7-AP08 2 AIR-CAP2702I-D-K9 f0:7f:06:8d:24:d8 7th Floor 1 IN 3
--More-- or (q)uit
FAL-7-AP10 2 AIR-CAP2702I-D-K9 f0:7f:06:8d:25:18 7th Floor 1 IN 1
FAL-7-AP14 2 AIR-CAP2702I-D-K9 f0:7f:06:bf:ad:e8 7th Floor 1 IN 1
FAL-7-AP01 2 AIR-CAP2702I-D-K9 f0:7f:06:bf:b0:4c 7th Floor 1 IN 1
FAL-7-AP07 2 AIR-CAP2702I-D-K9 f0:7f:06:30:92:bc 7th Floor 1 IN 1
FAL-7-AP13 2 AIR-CAP2702I-D-K9 f0:7f:06:30:91:80 7th Floor 1 IN 1
FAL-7-AP02 2 AIR-CAP2702I-D-K9 f0:7f:06:30:91:94 7th Floor 1 IN 1
FAL-7-AP05 2 AIR-CAP2702I-D-K9 f0:7f:06:30:91:e8 7th Floor 1 IN 1
FAL-7-AP12 2 AIR-CAP2702I-D-K9 f0:7f:06:8d:25:f0 7th Floor 1 IN 3
FAL-7-AP03 2 AIR-CAP2702I-D-K9 f0:7f:06:8d:25:e4 7th Floor 1 IN 1
FAL-7-AP06 2 AIR-CAP2702I-D-K9 f0:7f:06:30:91:84 7th Floor 1 IN 3
FAL-7-AP04 2 AIR-CAP2702I-D-K9 f0:7f:06:bf:b0:14 7th Floor 1 IN 1
FAL-7-AP09 2 AIR-CAP2702I-D-K9 f0:7f:06:92:b4:c8 7th Floor 1 IN 3
FAL-7-AP11 2 AIR-CAP2702I-D-K9 f0:7f:06:30:93:08 7th Floor 1 IN 1
Site Name........................................ MUMBAI-THIRD-FLOOR-AP
Site Description................................. MUMBAI-THIRD-FLOOR-AP
Venue Group Code................................. Unspecified
Venue Type Code.................................. Unspecified
NAS-identifier................................... Fractal-WLC1
Client Traffic QinQ Enable....................... FALSE
--More-- or (q)uit
DHCPv4 QinQ Enable............................... FALSE
AP Operating Class............................... Not-configured
Capwap Prefer Mode............................... Not-configured
RF Profile
2.4 GHz band..................................... <none>
5 GHz band....................................... <none>
WLAN ID Interface Network Admission Control Radio Policy
1 group for mumbai Disabled None
2 guest wifi Disabled None
*AP3600 with 802.11ac Module will only advertise first 8 WLANs on 5GHz radios.
AP Name Slots AP Model Ethernet MAC Location Port Country Priority
FAL-3-AP07 2 AIR-CAP2702I-D-K9 f0:7f:06:30:91:a4 3rd Floor 1 IN 3
FAL-3-AP09 2 AIR-CAP2702I-D-K9 f0:7f:06:8d:25:94 3rd Floor 1 IN 3
FAL-3-AP11 2 AIR-CAP2702I-D-K9 f4:0f:1b:73:00:74 3rd Floor- Eurek 1 IN 3
FAL-3-AP06 2 AIR-CAP2702I-D-K9 f0:7f:06:bf:ae:d0 3rd Floor 1 IN 3
--More-- or (q)uit
FAL-3-AP10 2 AIR-CAP2702I-D-K9 f0:7f:06:92:b5:88 3rd Floor 1 IN 3
FAL-3-AP08 2 AIR-CAP2702I-D-K9 f0:7f:06:92:b4:9c 3rd Floor 1 IN 3
FAL-3-AP03 2 AIR-CAP2702I-D-K9 f0:7f:06:bf:af:a0 3rd Floor 1 IN 1
FAL-3-AP12 2 AIR-CAP2702I-D-K9 f0:7f:06:92:b3:fc 3rd Floor- Eurek 1 IN 3
FAL-3-AP02 2 AIR-CAP2702I-D-K9 f0:7f:06:8d:25:28 3rd Floor 1 IN 3
FAL-3-AP01 2 AIR-CAP2702I-D-K9 f0:7f:06:92:b4:f4 3rd Floor 1 IN 3
FAL-3-AP04 2 AIR-CAP2702I-D-K9 f0:7f:06:30:92:8c 3rd Floor 1 IN 2
FAL-3-AP05 2 AIR-CAP2702I-D-K9 f0:7f:06:30:91:f4 3rd Floor 1 IN 3
Site Name........................................ RAHEJA-AP-GROUP
Site Description................................. RAHEJA-AP-GROUP
Venue Group Code................................. Unspecified
Venue Type Code.................................. Unspecified
NAS-identifier................................... Fractal-WLC1
Client Traffic QinQ Enable....................... FALSE
DHCPv4 QinQ Enable............................... FALSE
AP Operating Class............................... Not-configured
Capwap Prefer Mode............................... Not-configured
RF Profile
--More-- or (q)uit
2.4 GHz band..................................... <none>
5 GHz band....................................... <none>
WLAN ID Interface Network Admission Control Radio Policy
5 raheja-interface Disabled None
2 raheja-guest Disabled None
*AP3600 with 802.11ac Module will only advertise first 8 WLANs on 5GHz radios.
AP Name Slots AP Model Ethernet MAC Location Port Country Priority
FAL-RAHEJA-AP04 2 AIR-CAP2702I-D-K9 f0:7f:06:8d:24:1c Near Meeting Roo 1 IN 3
FAL-RAHEJA-AP02 2 AIR-CAP2702I-D-K9 f0:7f:06:8d:37:3c Confrennce Room 1 IN 3
FAL-RAHEJA-AP03 2 AIR-CAP2702I-D-K9 f0:7f:06:30:93:48 Near Confrence R 1 IN 3
FAL-RAHEJA-AP05 2 AIR-CAP2702I-D-K9 f0:7f:06:bf:ae:c0 Near Meeting Roo 1 IN 3
FAL-RAHEJA-AP06 2 AIR-CAP2702I-D-K9 f0:7f:06:92:b3:a0 Near Server Room 1 IN 3
FAL-RAHEJA-AP01 2 AIR-CAP2702I-D-K9 f0:7f:06:92:b3:20 Reception Area 1 IN 3
FAL-RAHEJA-AP08 2 AIR-CAP2702I-D-K9 f0:7f:06:8d:25:68 USER BAY ROAD si 1 IN 1
FAL-RAHEJA-AP09 2 AIR-CAP2702I-D-K9 f0:7f:06:92:b4:d4 Training Room 1 IN 1
--More-- or (q)uit
Site Name........................................ default-group
Site Description................................. <none>
NAS-identifier................................... Fractal-WLC1
Client Traffic QinQ Enable....................... FALSE
DHCPv4 QinQ Enable............................... FALSE
AP Operating Class............................... Not-configured
Capwap Prefer Mode............................... Not-configured
RF Profile
2.4 GHz band..................................... <none>
5 GHz band....................................... <none>
WLAN ID Interface Network Admission Control Radio Policy
1 group for mumbai Disabled None
2 guest wifi Disabled None
3 gurgaon-interface Disabled None
4 gurgaon-guest Disabled None
5 raheja-interface Disabled None
6 test Disabled None
Cisco Controller) >show flexconnect group summary
FlexConnect Group Summary: Count: 4
Group Name # Aps
Gurgaon-AP 9
HQ-3RD-FLR-AP-GROUP 12
HQ-7THFLR-AP-GROUP 14
Raheja-AP-Group 8
(Cisco Controller) >show flexconnect group detail Gurgaon-AP
Number of AP's in Group: 9
bc:16:65:13:71:00 GUR-AP-03 Joined Flexconnect
f4:4e:05:45:78:98 GUR-AP-08 Joined Flexconnect
f4:4e:05:78:ae:64 GUR-AP-04 Joined Flexconnect
f4:4e:05:78:ae:e4 GUR-AP-01 Joined Flexconnect
f4:4e:05:80:b3:2c GUR-AP-02 Joined Flexconnect
f4:4e:05:80:b3:e0 GUR-AP-06 Joined Flexconnect
f4:4e:05:80:b3:f8 GUR-AP-07 Joined Flexconnect
f4:4e:05:80:b4:44 GUR-AP-09 Joined Flexconnect
f4:4e:05:80:b5:18 GUR-AP-05 Joined Flexconnect
Efficient AP Image Upgrade ..... Disabled
Master-AP-Mac Master-AP-Name Model Manual
Group Radius Servers Settings:
Type Server Address Port
Primary Unconfigured Unconfigured
Secondary Unconfigured Unconfigured
--More-- or (q)uit
Group Radius AP Settings:
AP RADIUS server............ Disabled
EAP-FAST Auth............... Disabled
LEAP Auth................... Disabled
EAP-TLS Auth................ Disabled
EAP-TLS CERT Download....... Disabled
PEAP Auth................... Disabled
Server Key Auto Generated... No
Server Key.................. <hidden>
Authority ID................ 436973636f0000000000000000000000
Authority Info.............. Cisco A_ID
PAC Timeout................. 0
Multicast on Overridden interface config: Disabled
DHCP Broadcast Overridden interface config: Disabled
Number of User's in Group: 0
Vlan :........................................... 203
Ingress ACL :................................... None
Egress ACL :.................................... None
Vlan :........................................... 205
Ingress ACL :................................... None
Egress ACL :.................................... None
Vlan :........................................... 204
--More-- or (q)uit
Ingress ACL :................................... None
Egress ACL :.................................... None
Vlan :........................................... 206
Ingress ACL :................................... None
Egress ACL :.................................... None
Vlan :........................................... 207
Ingress ACL :................................... None
Egress ACL :.................................... None
Vlan :........................................... 208
Ingress ACL :................................... None
Egress ACL :.................................... None
Vlan :........................................... 209
Ingress ACL :................................... None
Egress ACL :.................................... None
Vlan :........................................... 210
Ingress ACL :................................... None
Egress ACL :.................................... None
Vlan :........................................... 211
Ingress ACL :................................... None
Egress ACL :.................................... None
Vlan :........................................... 212
Ingress ACL :................................... None
Egress ACL :.................................... None
--More-- or (q)uit
Vlan :........................................... 216
Ingress ACL :................................... None
Egress ACL :.................................... None
Vlan :........................................... 217
Ingress ACL :................................... None
Egress ACL :.................................... None
Vlan :........................................... 218
Ingress ACL :................................... None
Egress ACL :.................................... None
Group-Specific FlexConnect Wlan-Vlan Mapping:
WLAN ID Vlan ID
WLAN ID SSID Central-Dhcp Dns-Override Nat-Pat
(Cisco Controller) >
(Cisco Controller) >show wlan summary
Number of WLANs.................................. 6
WLAN ID WLAN Profile Name / SSID Status Interface Name PMIPv6 Mobility
1 FRACTAL-EMP-MUMBAI / FRACTAL Enabled group for mumbai none
2 FRACTAL-GUEST / FRACTAL-GUEST Enabled guest wifi none
3 FRACTAL-EMP-GURGAON / FRACTAL-GURGAON Enabled gurgaon-interface none
4 GURGAON-GUEST / FRACTAL-GUEST-GURGAON Enabled gurgaon-guest none
5 RAHEJA-EMP-WIRELESS / FRACTAL-R Enabled raheja-interface none
6 TEST-SSID / TEST-SSID Enabled test none
hope this will give you proper understanding. -
Managing vty ACLs with Prime Infrastructure?
I have a number of devices -- various models of Nexus, (2k - 7k), 6500s and some 1U stackables.
I'm trying to come up with a good way to leverage PI (2.1) to apply a vty ACL to the switches. There does not appear to be a template for this. The problem of course is not only the order of operation (remove ACL from vty if there is one so Prime doesn't lock itself out, only then do the rest of the stuff) but that the syntax seems to differ very aggravatingly -- some require "line vty 0 1509," some "line vty 0 1510," some platforms accept named ACLs for vty ACLs, some don't...
Any tips, tricks, or best practices on how to install and update vty ACLs on IOS and/or NX-OS devices with Prime Infrastructure?I am also interested in this topic. We have vty ACLs in place but with different names. Would like to be able to find and update the ACL's and vty config. Using PI 2.1.
-
Can I create a predictive AP layout in a MAP with Prime if I only bought a L-PI2X-BASE license?
Can I create a predictive AP layout in a MAP with Prime if I only bought a L-PI2X-BASE license?
Welcome to the discussions!
Sorry, can't help on the Vista front, but you might consider the Express as a first step and add the Extreme at a later time to replace the D-Link. The Express will be quick and easy to configure with a cable modem and if you are traveling, you can also use it to create a wireless network in your hotel room, providing ethernet jacks are available in the room.
Compatibility of the Apple stuff with other manufacturers, wireless wise is non-existent, so don't plan to use it to extend or broaden the wireless network created by the D-Link at home. Won't work.
You would have the option of creating a second wireless network at home with the Express if you plugged it into one of the ethernet ports on your D-Link router. The only change you would need to make in setup would be to switch Connection Sharing to Off (Bridge Mode) from the default setting of Share a single IP address. This would take less than a minute. -
Revision: 12883
Revision: 12883
Author: [email protected]
Date: 2009-12-12 15:53:50 -0800 (Sat, 12 Dec 2009)
Log Message:
Remove the skin classes from the halo theme project to avoid redundancy with the airframework/framework swcs.
QE notes: No
Doc notes: No
Bugs: SDK-24293
Reviewer: Glenn
Tests run: Checkintests, smattering of Halo and AIR mustella tests
Is noteworthy for integration: Yes
Ticket Links:
http://bugs.adobe.com/jira/browse/SDK-24293
Modified Paths:
flex/sdk/trunk/frameworks/projects/framework/src/FrameworkClasses.as
flex/sdk/trunk/frameworks/projects/halo/build.xml
Added Paths:
flex/sdk/trunk/frameworks/projects/framework/src/mx/skins/halo/WindowBackground.as
Removed Paths:
flex/sdk/trunk/frameworks/projects/halo/assets/
flex/sdk/trunk/frameworks/projects/halo/src/HaloClasses.as
flex/sdk/trunk/frameworks/projects/halo/src/mx/skins/ -
WLC integration with LDAP to authenticate domain users without Radius
Dear All,
I have a WLC 4404 with LWAPs, the customer has a microsoft LDAP and all users are joined to the domain and he wants the users to be authenticated against their domain accounts and this should be done automatically so that when users login to windows they are also authenticated and joined the WLAN.
so how we can do that with the simplest way, without Radius server using only the LDAP and wwithout envolving any certificates.
also i need to know when i add LDAP server to the WLC, how can i know that this LDAP is properly inegrated with the WLC ?
thanks and BRHi,
I have followed the following document to make users authenticate against their AD domain accounts:
http://www.cisco.com/en/US/products/ps6366/products_configuration_example09186a008093f1b9.shtml
the device and the root of PKI certificates for the WLC were generated and installed successfully on the WLC, and now we are in the client (end user) part starting from the section "Generating a device certificate for the client" page 17, which as per the document to be done from the client PC using the client domain account, which consequently means this process is to be repeated for each end user separately, so my question is there any way to generate some sort of general certificate for all clients to be pushed through group policy to all client instead of making it PC by PC ? -
WLC 5508 with version 7.0.98.0 and AIR-LAP1242ag
hi, recently i have deployed wlc 5508 with ap 1262. initially i had trouble with the existing version on the wlc (6..0.199.0) which AIR-LAP1262N-E-K9 was not registering with wlc. i have upgraded the wlc to 6.0.199.4 ver still it was not registering. finally i have upgraded to 7.0.98.0 and all the 40 AP's ( AIR-LAP1262N-E-K9 ) are addedd and its working fine.
Now my issue is, at the same site i have 12 nos of AIR-LAP1242ag autnomous AP's which i need to convert to lightweight ap and register with wlc. where i am stuck currently. after loading the recovery image (c1240-rcvk9w8-tar.123-7.JX9.tar) the ap reboots and can see it register with wlc within seconds contollers pushed the new image and once the ap reboots, never register again.
does anyone has any idea?After adding the country codes GB and RU.. in my test setup 1242 is registered...i will have it run for couple hours and see the result
ref: below
(Cisco Controller) >show ap uptime
Number of APs.................................... 2
Global AP User Name.............................. Not Configured
Global AP Dot1x User Name........................ Not Configured
AP Name Ethernet MAC AP Up Time Association Up Time
AP1cdf.0f66.79ca 1c:df:0f:66:79:ca 0 days, 00 h 43 m 35 s 0 days, 00 h 42 m 36 s
AP001e.be27.a7e6 00:1e:be:27:a7:e6 0 days, 00 h 16 m 56 s 0 days, 00 h 07 m 15
This issue sorted...thanks -
Cisco WLC 5508 with 3702APs - mobile hotspot for 2000 Guest users
Cisco WLC 5508 with 3702APs - mobile hotspot for 2000 Guest users
I've been given a fantastic "opportunity" by my boss to use our existing wireless infrastructure to provide internet access to potentially upto 2000 VIP guests arriving with BYOD devices, in a very densely populated area for a 3 day event. We are talking an area of approx 200m x 15m. Think of it as an awards ceremony/concert. The solution will also be mobile so we will be using internet breakout from different telcos as it will move to approx 20 countries. The area is also incredibly densely populated with other wifi APs. I did a brief site survey and AirMagnet could detect over 2500 other 'rogue' APs from where I was stood! I hope CleanAir works!
We need a simple authentication method for them to connect with zero admin from our side. We don't want to just offer up a rolling daily PSK as that's a bit amateur and we don't really want the VIP guests sharing the PSK with others during their stay. Ideally they could self-provision by providing an email address.
I know the WLC can handle webauth for local users but I don't think it scales very well. ie I don't think I can offer the account to several hundred people.
Cisco ISE looks a very expansive (and expensive) product but I don't think we need all it's capabilities (do I?). It would be nice to just ask a potential user for their email address and grant them access and email them next year. I've seen Cisco NAC but that looks over the top too for just guest users who will only be accessing a shared internet connection.
I've seen 3rd party supposed software solutions from Kiosk Antamedia etc do they work with Cisco Enterprise WLC solutions?
We'd like to limit users to a certain (low) bandwidth and block (say) torrent traffic to keep the general user experience worthwhile.
Does anybody have any case study documents or experience of such a project? As well as the authentication it's how well the APs will handle the dense potential number of clients trying to connect in such a confined space.
Any suggestions would be gratefully appreciated from the knowledgeable community.
Cheers,
MikeHi Rasika,
We are having WLC 5508 model with software version running 7.4.121.0. AP Models are AIR-CAP2602I.
Normally our WAN links are good even while the issue pertains. We are connected to remote offices over ipsec site to site vpn for WAN. The link latency in WLC between the AP and the controller shows <1ms.
currently the Guest network is using WPA2-PSK auth given in the controller. we are trying to find a option to make the Guest wireless auth local to the office, and see if this solves the problem.
any suggestions,
Thank you,
Arjun -
Using CWUTU 2.0 with Prime 2.2, How to?
I don't suppose anyone is using the ol' Cisco Works User Tracking Utility 2.0 with Prime.
Moving our LMS 4.2 to Prime 2.2 shortly and I pointed the CWUTU at the existing Prime 2.2 install (wireless) to see if could get a handshake. While certs were exchanged, the utility advisees to verify IP:port as no other response to query..Sorry but it can't be done.
UTU was a lightweight tool that, under the covers, talked directly to Prime LMS's Sybase SQL Anywhere database. Similarly the Prime LMS Widget did as well.
Prime Infrastructure uses an entirely different Oracle database and is thus not compatible with UTU.
There's currently no equivalent tool for the desktop and I've not heard of plans to introduce one. :(
There was the Cisco Prime iOS app that offers a "clients and users" view. It may be of use to you - I haven't had the chance to try it on a live system.
It appears Cisco has abandoned this app though since I can't find it on the app store anymore after looking just now. I do have it on my iPhone. :) -
ISE integration with Prime Infrastructure,
Hi Team,
I would like to know what are the advantages and Disadvantages of the ISE integration with Prime Infrastructre.Also how the LAN, wifi, and identity management part (guest access etc) will work together.
Cheers!!!
MinakshiPrime Infrastructure manages the wired and the wireless clients in the network. When Cisco ISE is used as a RADIUS server to authenticate clients, Prime Infrastructure collects additional information about these clients from Cisco ISE and provides all client relevant information to Prime Infrastructure to be visible in a single console.
When posture profiling is enforced in the network, Prime Infrastructure talks to Cisco ISE to get the posture data for the clients and displays it along with other client attributes. When Cisco ISE is used to profile the clients or an endpoint in the network, Prime Infrastructure collects the profiled data to determine what type of client it is, whether it is an iPhone, iPad, an Android device, or any other device.
Cisco ISE is assisting Prime Infrastructure to monitor and troubleshoot client information, and displays all the relevant information for a client in a single console.
Maybe you are looking for
-
Can I install my trail on an external drive?
can i download the trail CC onto an external drive if i don't have sufficient storage on my mac HD?
-
Saving a document using webdynpro application
Dear All, I am new in webdynpro development and I have a requirement to develop a webdynpro application which can save a document in a specified file directory. Can somebody please suggest or give sample code as to how to develope this application ..
-
BADI or Exits for Transaction FBL5N
HI All, I want any BADI or Exits for transaction FBL5N. Please help me out asap. <<Text removed>> Thanks in advance. Regards, Seevangi Edited by: Matt on Jan 13, 2009 11:25 AM - do not offer points
-
Hi For one finished product manufacturing one child part is required and is availble in storrage location. while creation of productin order system reserved this one child part. For the same finished product one more production order created by other
-
Time Capsule as Wireless Base Station...
I'll start with my current network map to give you the logistics - then ask my question. I think that might be easier! My Time Capsule is currently connected to my ISP modem. Wireless capabilities are turned off. I then have an Asus router hardlin