WLC release 7.4.110.0 and CPI 1.2.1

Hi fellows.
I need a quick answer regarding upgrading 5508 wireless controllers currently running 7.3.112 to 7.4.110
The answer is needed to asess if I MUST or mustn't do the CPI upgrade beforehand.
SInce this is for testing the functionality for apple devices and it is rather urgent I'm wondering what will or wont work if we dont upgrade CPI.
- I'm aware that 7.4.110.0 release notes states that CPI 1.3 is required - I need to klnow what function won't work
Appreciate you feedback.
Sincere Regards
/Mats

Here's a compatiblity Matrix...
http://www.cisco.com/en/US/partner/docs/wireless/controller/5500/tech_notes/Wireless_Software_Compatibility_Matrix.html#wp100373
ou didn't mention but I'm guessing you have 1.2 Prime Infrastructure now. You are correct 7.4 WLCs support doesn't show as supported for 1.2.
As Rasika above mentioned, go for the controller upgrade 1st then upgrade Prime second.
My guess is you probably won't lose anything but if you run into problems, it won't be supported.

Similar Messages

WLC 5508 and 7.4.110.0 and AP Blackhole?

So large customer had WLCs running 7.4.110.0 and it appears there was either a 3500/3600 AP memory leak or a CCKM roaming issue. The APs would occasionally blackhole traffic. You could see 2+ APs at -67dbm in 5GHz. Phones are locked to 5GHz, data rates matched. . Phone showed good strong signal, but 7925 users would report every couple days the phone dropping/DHCP timeout, re-registering, etc. We had a large CSE/TAC group onsite audit the 7925 Deployment Guide and setup, and we did a lot of cleanup but never hit the silver bullet.
After upgrading the 5508 to 7.4.121.4 (TAC special not on Cisco.com) they reported the 7925 problems have improved. Only been 1 day so far.
There is also a WPA2 with Preshared Key CCKM bug with the 7925s that roaming takes 2s. Use either strong WEP or buy 7926s, or use EAP/certificates, etc. https://tools.cisco.com/bugsearch/bug/CSCtt38270
7.4.121.0 Release Notes
http://www.cisco.com/c/en/us/td/docs/wireless/controller/release/notes/crn74mr02.html#wp1142453
We are running daily Traffic Stream Metrics (TSM) reports from Prime/WLC, and exporting the CallManager Diagnositc LQK records (export via CAR) to show if things are improving/etc.

Thanks Stephen, In my deployments of 7.4.110.0 version I have not seen this issue so may be controller reboot will fix it (we do have HA to minimize the impact). I will keep the thread updated with findings and may request TAC for the special release 7.4.121.0 if the still not happy with 7.4.110.0
Rick.

Announcing General Availability of PowerShell Connector and Release Candidate of Generic SQL and SAP Roles/Users

The FIM team is pleased to announce the availability of some additional Connectors for FIM2010R2.
General Availability of PowerShell Connector
The PowerShell Connector can be used to communicate with a system through PowerShell scripts. This allows an easy and flexible way to communicate with other systems but also to pre-/post-process data and files before handed over to the FIM Synchronization
Service. We believe the community will help providing scripts for this Connector for various systems and will open a place where scripts can be published for reuse.
TechNet docs:
http://go.microsoft.com/fwlink/?LinkID=393057
Download:
http://go.microsoft.com/fwlink/?LinkID=393056
Release Candidate of Generic SQL Connector
The Generic SQL Connector will allow you to connect to any database where you have an ODBC driver available. It enables new features compared to the built-in MA such as support for Stored Procedures, running SQL scripts, built-in delta import support, import
multiple object types, connect to multiple tables, and much more. This Connector is built on ECMA2.3 which allows schema discoverability to be customized in the Sync Engine UI. A pre-release of the next Sync Engine hotfix is included with the Connector download
and is required for the Connector to work.
Download:
https://connect.microsoft.com/site433/Downloads/DownloadDetails.aspx?DownloadID=52652
Release Candidate of SAP Users and Roles/Groups
The updated SAP templates for Users and Roles/Groups allows you to manage Users, Roles, and Groups in SAP. This also include password sync for Users to SAP. The Connector will make sure roles are represented as groups to make it possible to manage these
with bhold. This template will require the previously published WebService Connector:
http://go.microsoft.com/fwlink/?LinkID=235883.
Download:
https://connect.microsoft.com/site433/Downloads/DownloadDetails.aspx?DownloadID=52651
If you have participated in any other Connector preview program you will have access to the Release Candidate downloads. If you have not participated before then to get access to the preview programs on Connect either join the program “Identity and Access
Management”, “FIM Synchronization Service Connectors Pre-release” on
http://connect.microsoft.com/directory or follow this link
http://connect.microsoft.com/site433/SelfNomination.aspx?ProgramID=6709&pageType=1
We have also published an update to the Generic LDAP Connector adding support for some additional LDAP directories, see
http://support.microsoft.com/kb/2936070/. If you have additional LDAP directories you think we should support, please feel free to contact me.
                On behalf of the FIM Sync team,
                /Andreas Kjellman

On Tue, 18 Mar 2014 08:09:43 +0000, David Burghgraeve wrote:
We've been using the OpenLDAPXMA to be able to connect to ACF2 CA-LDAP (from Computer Associates) running on a IBM Z-OS Mainframe System. We've been using it for password synchronization since 2004 on MIIS. Today it's still used via the
OpenLDAPXMA (64bit) on FIM 2010 R2.
We had to tweak the password management component in the OpenLDAPXMA to support the error messages we get from the ACF2 System, as we support a multi-master password setup between Mainframe and Active Directory (one can change the password on
MF and/or on Windows). by example "LDP0406E ACF2 error modifying lid(ACF00155 NEW PASSWORD CANNOT BE THE SAME AS CURRENT PASSWORD)".
Additionally, we cannot get the delta import to work with the CA-LDAP, there's no capability in it and we tried to use the time attribute to use in the query for recent changes, but it does not work. (I think we need it in a large integer format
or unix time integer).
Would be great to have Microsofts' support in this :)
In a case like this where your follow-up has nothing to do with the
original post you should create a new thread.
Having said that, neither of the MAs to which you refer are official
Microsoft MAs and as such there is no support from Microsoft available.
Also, keep in mind that the ECMA1/XMA extensibility framework has been
deprecated and replaced by the ECMA 2.0. You should plan on replacing
existing ECMA1 management agents with ECMA2.0 connectors.
Paul Adare - FIM CM MVP
"It's 106 light-years to Chicago, we've got a full chamber of anti-matter,
a half a pack of cigarettes, it's dark, and we're wearing visors."
"Hotsync." -- Paul Tomblin & Peter da Silva

11/12/2013 - Release - AIR 3.9 Runtime and SDK

Today we're pleased to announce that the next version of AIR is available for immediate download. This update includes the following new features and improvements:
New Features:
Mobile Workers (concurrency) BETA - Android
Our hugely popular desktop feature, AIR Workers, is now making its debut on mobile! We have added support on Android devices so that you will be able to execute code in the background without interrupting your application’s main code. Your UI will remain responsive, enhancing the user experience. We haven’t forgotten about iOS! Look for news on iOS workers in an upcoming release (NOTE: this feature will undergo an extended beta period.)
AIR Mobile Support for Background Execution in “Direct” Render Mode
AIR now supports background execution on iOS and Android when render mode is set to “direct”. This will allow your applications to perform tasks such as audio playback even when invisible to the user. Due to power and CPU considerations, we recommend reviewing our release notes for additional details and guidance.
In the past AIR on iOS and Android did not support background execution when render mode direct was set. Due to this restriction, Stage3D based apps were not able to execute background tasks like audio playback, location updates, network upload/download etc. iOS does not allow OpenGLES/rendering calls in the background. Applications which attempt to make OpenGL calls in the background are terminated by the iOS. Android does not restrict applications from either making OpenGLES in the background or other background task(like audio playback).
With this feature, we will now allow AIR mobile apps to execute in background when renderMode direct is set. AIR iOS runtime will throw an error if OpenGLES calls are made in background. However no error will be thrown on Android, as Android native apps are allowed to make OpenGLES calls in the background. It's recommended to not make rendering calls while your app is executing in the background as its important to utilize the mobile resources judicially. The following is a list of Stage APIs which may throw the error 3768 - The Stage3D API may not be used during background execution. The swf version should be 22 and above.
Context3D.clear
Context3D.present
Context3D.createVertexBuffer
Context3D.createIndexBuffer
Context3D.drawToBitmapData
IndexBuffer3D.uploadFromVector
IndexBuffer3D.uploadFromByteArray
VertexBuffer3D.uploadFromFloat
VectorVertexBuffer3D.uploadFromFloat4
VectorVertexBuffer3D.uploadFromByteArray
Program3D.upload
Texture.uploadCompressedTextureFromByteArray
Texture.uploadFromBitmapData
Texture.uploadFromByteArray
CubeTexture.uploadFromBitmapData
CubeTexture.uploadFromByteArray
CubeTexture.uploadCompressedTextureFromByteArray
RectangleTexture.uploadFromBitmapData
RectangleTexture.uploadFromByteArray
AIR Support for iOS7
iOS7 has launched and we are making sure that AIR is compatible and performs as expected.
AIR Mac OS 10.9 Support
We have tested against the latest developer releases of OS X 10.9 and are making sure that your applications support the latest technologies such as “App Nap”.
AIR XXHDPI (144 x 144) Icon Support for Android
With this feature we have added support for beautiful, high resolution icons on devices such as the Nexus 10.
Notable bug fixes:
[3650590] [OSX] - App Updater Crashes on MacOS with Air 3.9
[3648442] [iOS7] - Leftmost part of the text in spark TextArea and stageText get clipped when mulitline property is true.
[3640207] [Android] [Captive Application] - orientationChange event handler fetches wrong stage.orientation values.
Known Issues:
[3616981] [iOS] - Sound gets stop on clicking Power button even when UIBackground tag value set to Audio in application.xml
For further information please see our release notes.
Download Locations:
AIR 3.9.0.1210 runtime for Windows: 3.9 Runtime Download
AIR 3.9.0.1210 runtime for Macintosh: 3.9 Runtime Download
AIR 3.9.0.1210 SDK & Compiler for Windows: 3.9 SDK & Compiler Download
AIR 3.9.0.1210 SDK & Compiler for Macintosh: 3.9 SDK & Compiler Download
Note: To provide all the all the necessary tools for our developers in one place and avoid having to download multiple components, we are packaging Adobe AIR 3.9 SDK and ActionScript Compiler 2.0 in a single SDK called “Adobe AIR 3.9 SDK & Compiler”.
AIR SDK 3.9.0.1210 (Compatible with Flex) for Windows: 3.9 SDK Windows Download
AIR SDK 3.9.0.1210 (Compatible with Flex) for Macintosh: 3.9 SDK Macintosh Download
Previous versions of the AIR runtime and SDK can be found on the Archived AIR SDK and Runtimes page

110/220V and 60/50 Hz on SONY

I'd like to buy a Sony TV from your website to use it in the U.S.A for a couple of years and the to be able to go back to Europe with the TV.
I can see on the specifications:
Power Requirements (voltage): AC 120V for UL,cUL; AC 110-240V for other
Power Requirements (frequency): 60Hz for UL,cUL; 50/60Hz for other
does it mean that I can use the TV with 50 Hz and 220V (Europe) as well as in the USA (dual voltage and dual frequency)?
Thank you guys.

No; The power specifications cover all available models, but any model that you purchase for North American use will be 110/120 and 60Hz. It will also be compatible with NTSC only, and will not be compattible with PAL and SECAM, both of which are used in various parts of Europe.
If you find my post useful or informative, please click the icon below with the plus sign and star to give kudos. Thank you!

So apple just released its iphone 5 c and iphone 5s but will apple be releasing an ipod touch 6th generation this yr??

so apple just released its iphone 5 c and iphone 5s but will apple be releasing an ipod touch 6th generation this yr??

Apple has not said anything about that so no one on here would now. All we can do is wait and see.

I want to download an album but its only been released in the US site and im in Australia, how do i get it d

I want to download an album but its only been released on the US site and im in Australia, how do i get it

You can't.
If you have a US-address credit card, you could use it to set up a new account, but you'll runs into all sorts of other problems.

New patch releases: JE 5.0.48 and 4.1.20

All,
Please note that new patch releases for JE 5.0 and 4.1 are now available.
The JE 5.0.48 update contains a number of critical bug fixes that can cause corruption (data loss) under certain circumstances. We strongly recommend that anyone using JE 5 upgrade immediately to 5.0.48. This update also contains fixes for issues that prevent upgrading to JE 5 from an earlier release, or cause problems after upgrading.
Note that running the pre-upgrade utility is mandatory before upgrading to JE 5 from an earlier release, and the pre-upgrade utility must be run using JE 4.0.20. The JE 4.0.20 update contains fixes to the pre-upgrade utility as well as one critical bug fix. See the first section in the JE 5.0.48 change log for detailed information on upgrading and running the pre-upgrade utility.
We'd like to thank all the users who reported problems and especially those who worked with us over email, in some cases for long periods of time, to diagnose problems and test fixes. Some, but not all, of those who helped are mentioned in the change log. Thank you for contributing to the reliability of the product!
Complete information can be found in the JE documentation. The release is available via the download site or Maven.
--mark

Hi,
the biggest problem is that we are using bought application not made in our company. I have tried out this java application with JRE 1.4 and 1.5 and it just doesn't work. So the only solution is using JRE 1.3 on all intranet computers. This application uses digital certificate so why doesn't Sun allow digital signet java programs to run on older versions of JRE?
There could also be one more solution. I exactly know md5sum (or sha1sum) of 3 JAR files used by applet needing JRE 1.3. So if this sum would be enabled manualy (or I could send batch file to make this in registry or any other storage this would be good).
http://en.wikipedia.org/wiki/Md5sum
http://en.wikipedia.org/wiki/Sha1sum
Thanks,
Grofaty

Release dates of nteweaver 2004 and netweaver 2004's and XI 3.0 and PI 7.0

Hi,
i would like to know the information of the following:
release dates of NetWeaver 2004 and NetWeaver 2004's and SAP XI 3.0 and SAP PI 7.0
kalyan.

Kalyan,
NetWeaver 2004 released on April 2004.
source -http://www.sap.info/index.php4?ACTION=noframe&url=http://www.sap.info/public/INT/int/index/PrintEdition-98954086245278b01-int/-1/articleContainer-1887240879c3b1916e
NetWeaver 2004's released on June 2006.
Source -/people/michael.eacrett/blog/2006/06/07/whats-new-in-sap-netweaver-702004s--an-introduction-to-the-functionality-deltas-and-major-changes
Best regards,
raj.

Abap Lists - Printing - defining font and CPI and applying to printed text

Hi,
I am trying to define some forms for matrix printing. I should change the font type, and CPI.
We will print ABAP Lists.
I see my fonts (courier, 100, 12CPI, Prnt.Ctrl SF005) are defined in SE73.
In SPAD - device type (choose spec. one) u2013 Print Controls (tab) I can see SF005, marked u201EDirectu201C column, as well as u201EHexadecimalu201C. Control Character Sequence is 1B6B001B4D121B57001B461B35.
I can see 31 more SFxxx Print controls here.
How do I apply specific Print Controls (SF005) from this list to a printed document? (I assume this is the list of available prnt.ctrls that can be used for printing, but how do I "select" specific ones and apply them to document print?)
How do I choose u201ECOL0N: Color off, normal fontu201D (intensified OFF u2013 I heard that sap print in bold by default)?
Thanks in advance,
cheers,
Nenad
P.s. u2013 in printer settings the default font is Coourier 10, 12CPI, draft output. If I change this settings on printer directly, no effect is applied on printed documents... Printing from ECC 6.0
Edited by: Nenad Nikolic on Oct 26, 2010 4:49 PM - details...

hi again,
more info:
In Formats (Z_fakt1) - Formats (tab): u201EPrinter initializationu201C, I can see some predefined settings, but it is copied from some IBM printer, and I wonder is it correct. There is nothing about font type:
#reset
\e\0x40
select US-ASCII character set
\e\0x52\0x00
set line spacing 6 LPI
\e\0x32
set page length to 12 inch (=72 lines at 6 LPI)
\e\0x43\0x48
cancel bottom margin
\e\0x4F
set left margin to 0
\e\0x6C\0x00
select draft quality
\e\0x78\0x00
select non-proportional spacing
\e\0x70\0x00
cancel condensed printing
\0x12
disable double-width printing
\e\0x57\0x00
select 10 CPI
\e\0x50
Result here is: 11CPI. Bold. Looks like "Times New Roman"
The exact copy from IBM printer is used for another format (Z_fakt2), nothing is different except:
select 12 CPI
\e\0x4D
Result here is: 10CPI. Bold. I am under BIG impression that the font type is different. But it is possible the font looks different just due to a size difference. Looks like "Courier New"
In both cases I print predefined text with same output device, same device type.
When I set 15CPI (0x67) u2013 I still get 10CPI, just the font looks more plain, more "draft" then before - like once in DOS. I am certain that these font type is definitely different then before (for example, here "W" have parallel endings). These fonts are even more suitable for these reports...
Shouldn't the fonts be SMALLER and more of them in 1 inch (15 characters per inch) now then 10CPI (10 character per inch - less characters to fill 1 inch)??
If I set 1CPI - shouldn't there be just 1 big character on 24,5mm?
When I delete all entry (except # reset \e\0x40) from "Printer initialization" for one Format, the print output looks exact as before deleting (and saving)?!
I would like to set Courier font, (really 12CPI), plain text, no bold.
Where should I set this options?
Thanks and sorry for long input, but the more info you have, the more insight ou have in my problem...
Cheers,
N
Edited by: Nenad Nikolic on Oct 26, 2010 5:30 PM - update

Preview Release of WebLogic Portal 9 and Workshop 9

I would like to get my hands on a developer preview release of WebLogic Portal 9 and Workshop 9. I can't seem to find it online so I'm hoping someone can point me in the right direction. We're currently evaluating portal products and I would hate to decide against BEA based on the lack of availability of the forthcoming version.
Anybody know where a developer release of either of these two products can be found?

The Technology Preview for WLP 9.x and WLW 9.x will be available in early December. Please contact your BEA account team to let them know that you are interested.
At present the plan is to have a GroupSpace community site for use by all customers participating in the Technology Preview. A BEA technical field staff member (SE, PS, etc.) assigned to your account will use this site to send you an invitation, and when you join you will have access to the installation. Questions, discussions, etc. for the Technology Preview will all go through the GroupSpace site. If you don't know who your BEA technical account member(s) are, you should find out as they will be the key to obtaining the Technology Preview.
If you can't wait for the Technology Preview, please ask your BEA acount team to contact myself or others in Product Management. We'll be happy to go over the product features, show you demos from current builds, etc.
Thanks,
Skip Sauls
Senior Product Manager, WebLogic Portal

HT4889 can you stop in the middle I am transferring 600gb wirelessly and it says 110 hours and it has been working all night? I need my computer for work?

I am transferring my 2009 27" iMac to a new 27" 768gb flash drvie with 32gb ram via wireless and it is taking 110 hours and has been on overnight. I have the thrunderbolt to firewired adapter but I could not get it to mount my
buffalo thunderbolt external even though it mounts my firewire Lacie 800 which is why I am doing it wirelessy I do not have 110 hours it is work related computer I run three companies.
can i plut in the thunderbolt and try it with the firewire adapter in the middle of migration and remove the ethernet cable it was only 50 hours when it was doing it wireleslly and now 110 with the ethernet cable I am going to try removing it at least.
<Email Edited By Host>

VikingOSX wrote:
You run three companies. That means that the cost of your time exceeds what should be invested to migrate your data. It also means that a keen business mind quite often does not have the patience for this sort of thing. Pay someone you trust $100 to do this migration for you, and repurpose your current stress levels into new 2013 business opportunities.
$100?
That is a very small price for such a high value migration.
Re-assess your rates

Why is apple releasing the ipad4 witha new and inproved wifi attena without addressing the wifi issue in the ipad3

Why is apple releasing the ipad4 witha new and inproved wifi attena without addressing the wifi issue in the ipad3

Jim Level 5 person ....I am very happy for you that your usage will not be affected, please accept my congratulations.
Now I have to point out that going ballistic has certain connotations but posting on an internet forum is not one of them.
I appear to be one of thousands who are all expressing their outrage in a rational and intelligent manner which cannot be said for your lebvel 4 + collegues on this forum.
Finally there has been an ongoing issue wiith the iPad 3 Wifi on certain wifi only models , I have not encountered it and it seems clear neither have you. That of course does not discount the fact that many others have experienced this issue , an issue which may reveal itself to you or I in the future particularly as I have only been using mine for a fortnight.
The following is a relevant link for your information :
http://9to5mac.com/2012/04/04/apple-investigating-new-ipad-wifi-issues-tells-app lecare-to-replace-affected-units/

I have just bought iphone 5 and i have a problem in charging it , firstly it took a long time to charge when i opened it to the first time , and its nearly dont charge on 110 output, and its taking a long time to charge on 220 reaches 50% in 1 hour

I have just bought iphone 5 and i have a problem in charging it , firstly it took a long time to charge when i opened it to the first time , and its nearly dont charge on 110 output, and its taking a long time to charge on 220 reaches 50% in 1 hour is this normal?

The charger block is universal and is able to handle multiple votages. One hour to reach 50% seems fine to me if the phone was completely flat to start with. Just leave it on charge for as long as it takes to reach 100%. I leave mine connected overnight all the time and it does not harm the battery

My iphone is showing the apple pic so i Pressed both home and sleep/wake buttons until the Apple logo appears, then release the sleep/wake button and continue pressing the home button alone until iTunes detects and Recoveys but it is gives an error 1051

my phone was showing the apple pic when i eraseed all content and settings so i did Pressed both home and sleep/wake buttons until the Apple logo appeared, then released the sleep/wake button and continued pressing the home button alone until iTunes detected the phone in Recovery Mode but an error is coming (1015) plz help me!!!!

plug into itunes and take it from there
http://support.apple.com/kb/HT1808

WLC release 7.4.110.0 and CPI 1.2.1

Similar Messages

Maybe you are looking for