WLC with AP´s different ap´s brands

The Cisco WLC it´s able to handle aps of differents brands?

Although CAPWAP is an industry standard the CIsco WLC product line will only support Cisco APs.

Similar Messages

  • Client Roaming Within Single WLC with Different AP Groups

    I am trying to setup a 4400 WLC with 2 different AP Groups mapped to its respective Dynamic Interfaces / Vlans. AP's are equally mapped to both the AP groups by Floor wise ex: First floor AP's connect to one AP group and the Second Floor AP's connecting to other AP group.
    Goal is to create separate Network policy for each Floor using ACL's and apply to their respective Vlans on Layer 3 Switch. Wireless Raoming should happen seamlessly between these Ap groups making the DHCP changes by not disconnecting and connecting every time user roam across the Floors.
    Problem is When Clients Roam between Floors i,e moving between AP Groups, they still maintain their old DHCP IP addresses when moved to new AP group even after Client re-authetication. This defies our goal of creating a Wireless Network Policy using single WLC.
    Knobs i have tuned in WLC to acheive our goal includes....
    1. WLAN Session Timeout - No use
    2. DHCP Proxy Disable - No Use
    3. ARP Time out - No use
    Looks like WLC is storing the IP address and MAC information of the Client unconditonally during roaming and clearing out untill a manual or forced disconnect or disassociation is done.
    Did anyone tried to implement this setup and made it running? Any help or suggestion would be higly appreciated.
    Thanks
    Guru

    abit late for a reply but....try going to the SSID>Advanced and ticking the "DHCP Addr. Assignment" Required checkbox and test again.
    What does the DHCP Required field under a WLAN signify?
    A. DHCP Required is an option that can be enabled for a WLAN. It       necessitates that all clients that associate to that particular WLAN obtain IP       addresses through DHCP. Clients with static IP addresses are not allowed to       associate to the WLAN. This option is found under the Advanced tab of a WLAN.       WLC allows the traffic to/from a client only if its IP address is present in       the MSCB table of the WLC. WLC records the IP address of a client during its       DHCP Request or DHCP Renew. This requires that a client renews its IP address       every time it re-associates to the WLC because every time the client       disassociates as a part of its roam process or session timeout, its entry is       erased from the MSCB table. The client must again re-authenticate and       reassociate to the WLC, which again makes the client entry in the table.

  • Does anyone get a vibration sound when talking on the iPhone6? It doesn't happen all the time and happens with talking to different people.

    Does anyone get a vibration sound when talking on the iPhone6? It doesn't happen all the time and happens with talking to different people. I have tried to troubleshoot it, but can't find a answer.

    Hey CEVYNBARRY!
    Here is an article for you that will help you address this issue:
    Troubleshooting "A connection failure has occurred", "The specified server could not be found" or similar messages
    http://support.apple.com/kb/ts1843
    Take care, and thanks for visiting the Apple Support Communities.
    -Braden

  • Okay so my IPod touch 4 won't play music through any headphone I put into the port. I've tried it with 4-5 different headphones but it still won't work.  How can I fix this?

    Okay so my IPod touch 4 won't play music through any headphone I put into the port. I've tried it with 4-5 different headphones but it still won't work.  How can I fix this? This isn't the first time something like this has happened but it has never stayed this way for such a long time. If I have to send it in for repairs I will but I'm not sure if its under warranty

    To check for warranty coverage:
    https://selfsolve.apple.com/agreementWarrantyDynamic.do
    - Try cleaning out/blowing out the headphone jack. Try inserting/removing the plug a dozen times or so. There is a little switch in the headphone jack that disconnects the speaker when the headphone jack is inserted.
    Try the following to rule out a software problem
    - Reset the iOS device. Nothing will be lost
    Reset iPod touch: Hold down the On/Off button and the Home button at the same time for at
    least ten seconds, until the Apple logo appears.
    - Reset all settings
    Go to Settings > General > Reset and tap Reset All Settings.
    All your preferences and settings are reset. Information (such as contacts and calendars) and media (such as songs and videos) aren’t affected.
    - Restore from backup
    - Restore to factory settings/new iOS device.
    - Make an appointment at the Genius Bar of an Apple store. Seems you have a bad headphone jack.
    Apple Retail Store - Genius Bar
    If not under warranty Apple will exchange your iPod for a refurbished one for $199 for 64 GB 4G and $99 for theother 4Gs. They do not fix yours.
    Apple - iPod Repair price                  
    A third-party place like the following will replace the jack for less. Google for more.
    iPhone Repair, Service & Parts: iPod Touch, iPad, MacBook Pro Screens
    Replace the jack yourself
    iPod Touch Repair – iFixit

  • Why does a new desktop creation unexpectedly initiate with a background differing from the originating desktop? How can I control or eliminate this behavior?

    Why does a new desktop creation unexpectedly initiate with a background differing from the originating desktop? How can I control or eliminate this behavior?

    CT, I suspect that I either mistated the question or don't understand how to set the default back ground.  In any case, with the background that I have set in system settings, and this is the background to which my sessions consistantly boot, new desktops come up for the second or up to the third background with this initially set background. Then in the third or fourth desktop creation (I seldom go beyond four), the background for the new desktop, is one that I was using one or two months ago...

  • Can i Match invoices with a currency different from the purchase order curr

    Dear Valued Consultant,
    Can i Match invoices with a currency different from the purchase order curr
    Thanks

    Hi,
    As a functionality, Payables will not allow matching an invoice to a purchase order that is in a different currency.
    Refer Oracle Public sector payables user guide for 11i (page 4-94).
    I understand that there is an enhancement request (3286623) logged for this functionality.
    Please refer Note:172291.1
    - Thiagu

  • Wlc with redirect-acl

                       Hi, I'm using ISE and I want to redirect https traffics to one web-page.
    so I used cisco-av-pair = url-redirect=test123
    also, test123 is existed in WLC with
    deny https any
    deny any https
    permit ip any any
    however, it does not redirect to the web-page.
    after client is accessed to wifi, when I see client on wlc, redirect-url is not applied but aaa-overide acl is applied to test123
    anyone know why ?
    I'm using ISE 1.2.0.899 with 1,2,3,4,5 patches
    and wlc 7.4.115

    Please refer below:
    http://www.cisco.com/c/en/us/support/docs/security/identity-services-engine/115732-central-web-auth-00.html

  • Place one order with Products from different sales orgs

    Hello,
    We are in CRM 7.0 EHP2 connected to ECC 6.0. We have Internet
    sales/Webchannel Application.
    We are rolling out Internet sales for a new country but they want the option to
    place one single order with products from different sales
    organizations.
    Currently Customers send fax/email to customer
    representative(CR) with list of products. The CR identifies and places
    multiple orders if products belong to different sales orgs.
    Currently customers don't have idea about sales orgs and they don't
    have a clue which product belongs to which sales orgs. So, for them to
    use Internet sales, we have to provide them an option to place one
    order with products from different sales orgs.
    I understand SAP doesn't support this. But, is there any way we can achieve this through some custom/out of the box solutions?
    Thanks,
    Ravi

    Hi Ravi,
    Please have a below help link, it may help you to explain the role of Distribution Channel and if it fits to your requirement.
    Organizational Data Determination in CRM E-Commerce - E-Commerce - SAP Library
    Thanks,
    Hamendra

  • Does WLC with 4.1support 350 WGB

    Hi all,
    can anyone tell me if it is also possible to connect a 350 WGB to a WLC with version 4.1.171.0?

    Hi UWE-HEINZ ,
    The 350 is not going to work due to the required IOS needed to function with the WLC 4.1.171.0. Have a look;
    Workgroup bridge (WGB) support - Cisco Aironet autonomous access points operating in WGB mode can now associate to Cisco Aironet lightweight access points (except Cisco Airespace AP1000 series access points) to provide an 802.11 wireless connection to wired devices. The WGB is supported only in client mode and not in infrastructure mode and must run Cisco IOS Release 12.4(3g)JA or later (on 32-MB access points) or Cisco IOS Release 12.3(8)JEB or later (on 16-MB access points). WGB functionality is not supported for use with hybrid REAP.
    The autonomous WGB access point learns the MAC address of the wired client and then informs the lightweight access point and controller that the device is operating on the wireless network. This scenario provides transparent bridging for wired clients and secure roaming.
    From these release notes;
    http://www.cisco.com/en/US/products/ps6366/prod_release_note09186a008082d849.html#wp147320
    Release Notes for Cisco Aironet Access Points for Cisco IOS Release 12.3(8)JEB
    April 26, 2007
    These release notes describe minor features and caveats for Cisco IOS Maintenance Release 12.3(8)JEB. They also provide important information about Cisco Aironet 1100, 1200, and 1230 series autonomous access points. The Cisco Aironet 350 series is no longer supported in this release or any future release.
    http://www.cisco.com/en/US/docs/wireless/access_point/ios/release/notes/b38jebrn.html#wp23144
    Release Notes for Cisco Aironet Access Points for Cisco IOS Release 12.4(3g)JA
    April 26, 2007
    These release notes describe features, enhancements, and caveats for special technology early deployment release Cisco IOS Release 12.4(3g)JA. Release 12.4(3g)JA supports 32 Mb Cisco autonomous access points including Cisco Aironet 1100, 1130, and 1240 series access points, 1300 series access point/bridges, and 1400 series bridges.
    http://www.cisco.com/en/US/docs/wireless/access_point/ios/release/notes/b41jarnh.html#wp23144
    Hope this helps!
    Rob

  • WLC With ASA as gateway

    Hi ALL,
    Has any one configured a WLC with ASA as the gateway, I have 3 interface 70, 80 and 90 ( 70 is the management vlan ) in the WLC, with all the gateway in the ASA. But I can ping only the gateway for vlan 70 from my wlc, none of the other gateway's are reachable.
    Let me know if any one have faced this issue before
    Thanks
    NikhiL

    Probably the other ASA interfaces are configured to be non pingable ? that's quite common.

  • Cisco WLC with ISE - need to restrict access during non-business hours

    Hello,
    We have a requirement to turn off our wireless during non-business hours.  We have a 5508 WLC with ISE.  What is the best way to accomplish this task?  
    Thank you in advance.
    Beth

    Aside from Steve's respond, there are several methods of doing this and this will all depend on how complex your network is and how technical you want to do this.  
    1.  As what Steve said, use PI and you can define several schedules when to turn off/on the SSID; 
    2.  If you have corporate access, you can use AD to schedule non-business hours; 
    3.  If you have Cisco PoE switches, you can enable EnergyWise to power off the APs; 
    4.  If you manage your core network, you can enable time-based ACL to disable the default gateway of the dynamic interface which is attached to your SSID.  
    The most "destructive" method is option #3, because there are chances that your AP won't power up properly, if not power up at all.  

  • Attach WAP4410N as WGB to Cisco 5760 WLC with LWAP 3702

    I have 5760 WLC with 3702 wireless infrastructure. Can i connect a WAP4410N AP as WGB to be attached to my current wifi network so i can provide connectivity to some wired devices? Any tips on doing so? And any limitation can be imposed for using this WAP instead of any other AP that are supported by WLC5760? If the wired clients are passive, configuring passive-client on WLC will work normally?

    Thanks Eric for the reply, however, this AP is not expected to be controlled by WLC as you mentioned since it is not lightweight and not supported by this WLC for compatibility. But in this scenario, i'm talking about operating it in WGB mode to be attached to the unified wireless infrastructure. In this scenario, it is just attached as a client that pass the traffic of its clients to the other side.
    I have noticed the below statement in this guide page (539)
    http://hcsdemo.com/c/en/us/td/docs/switches/lan/catalyst3650/software/release/37e/consolidated_guide/b_37e_consolidated_3650_cg.pdf
    When non-Cisco WGBs are used, the switch has no information about the IP address of the clients on the wired segment behind the WGB. Without this information, the switch drops the following types of messages:
    • ARP REQ from the distribution system for the WGB client.
    • ARP RPLY from the WGB client.
    • DHCP REQ from the WGB client.
    • DHCP RPLY for the WGB client.
    Accordingly, if the switch will drop all this traffic, then no traffic will be passed from the WGB clients to the network ! what I’m missing here?!!!

  • License in HA SSO WLC with 7.3 version

    Hi,
    We are looking at deploying two 5508 in new HA SSO scheme with version 7.3, now our actual scenario is  a wlc primary and secondary with 100 ap license each one. In this new scenario the two licenses are added in 200 ?
    Thanks,
    Marco Muñoz

    Hi,
    1. for the HA software used, please go for 7.4.110.0 NOT 7.3
    2.the license on the secondary will not be added to the primary, the way it works, you buy either an HA-SKU  part number WLC, or a normal 5508 WLC with 50 AP base license, you will lose the 100 license on the secondary, and will end up with only 100 AP license.
    i would really suggest that you read the following guide for clear information.
    http://www.cisco.com/en/US/products/ps10315/products_tech_note09186a0080bd3504.shtml

  • Issues with text on different OS

    Hi,
    On the "credits" section of my site,
    www.danielwaltermusic.com, I am having an issue with text appearing
    differently on OSX vs Windows. On OSX the text appears normally,
    with the links located exactly where they are supposed to be. On
    Windows XP and Ubuntu 2.22.3 (only systems I've been able to check
    it on) the links are located improperly like so:
    http://www.danielwaltermusic.com/awoa/siteexample.JPG
    If anyone can point me in the right direction, that would be
    great. My web designer is not using dynamic text so that is not the
    issue.
    Also, if someone could help us figure out how to get the web
    player to play songs sequentially (as it is, the player stops after
    one song) that would be great.
    Thank you so much!

    Hi - thanks for your reply.
    I try not to use Iphoto, although it does sometimes kick in before i can cancel it. Normally, i copy the records from the card to the Imac hard drive.
    I'm assuming the CF card may have been formatted by a previous windows machine at some point. Is this likely to be an issue?
    imac G5   Mac OS X (10.4.5)  

  • Duration of upgrade WLC with 75 AP

    I'm planning to upgrade a 4404 WLC with 75 LWAPP's, from 5.1 to 5.2.193.
    I read that after the WLC upgrade the AP's are automatically upgraded in groups of 10 and that the upgrade can last as long as 30 minutes. Does this mean some AP's are not functional for 30 minutes? Or do the AP's work while they still have the lower software version, and only are not functional during their own upgrade of about 3 minutes? And is there a way to choose these AP groups yourself? I can't find this in the documentation.
    Thanks in advance,
    Albert

    (Assuming you have one controller) I think the AP's will go offline when you reboot the controller after the controller upgrade. The APs will not come back online until they have upgraded their firmware and re-joined the controller. On our last upgrade (controllers running 4.2, upgrading to a later rev of 4.2, we use 1242 AP's), it took about 5 minutes for a given AP to complete an upgrade. 2 controllers and ~250 AP's took less than an hour.

Maybe you are looking for

  • Setting max length of the field when using Context Model Node

    I have created a model using Import Adaptive Web Service model option (a web service was a wrapper around SAP BAPI function module). There were no dictionary types created in the Local dictionary as a result of import. I have mapped the context of th

  • Removing Outer Single Quotes for WHERE IN Clause from Join(Parameters)

    Hello, I am passing a multi-valued parameter into a dataset from a TypeBusiness dropdown list: =join(Parameters!prmTypeBusiness.Value,",") Here is the dataset query behind the TypeBusiness dropdown parameter list: SELECT     type_bus_code, bus_desc F

  • Facetime isnt working properly

    My facetime keep cutting and dropping the call, wasn't like that before update's and this Icloud stuff, anyone know what i've to do?

  • 'Pages' is not emailing my doc

    Keeping it short and simple, I want to send my doc compiled on 'Pages' to my gmail and hotmail address. Pages acts as if it has sent it, although nothing comes through on the otherside. The email addresss are correct and my internet is fully function

  • Photoshop Elements 11.0 doesn't start.

    After download of Photoshop Elements 11.0 on hewlett packard XP computer, it will not run because ".exe" file cannot be found.  Why not?