WLC with LAG mode enable connected to a switch HP in LACP mode

I am trying to connect a WLC 4402 5.0.148.0 mode with an HP 2800 switch. The switch is configured thunk mode with LACP protocol.
The WLC in LAG mode uses the protocol LACP? How can configure them switch HP?
Thanks.
Mirko Severi.

not supported, Mirko. Refer to this for further detail:
http://www.cisco.com/en/US/docs/wireless/controller/4.0/configuration/guide/c40mint.html#wp1186245

Similar Messages

OEAP 600 cannot join WLC with auth-list enable

I've got a strange problem here. In the office, my OEAP 600 can join WLC if there is no MAC authentication. When i enable MAC authentication at WLC, AP will fail to register. However, I try it at home and it works with both MAC authentication enable or disable. I suspect it is because of firewall in my office, but there shouldn't have any different in discovery and joining procedure for AP with MAC authentication enable or disable. I'm confused here. Please help.

Justin,
Below is error summary from WLC:
Last Error Summary
Last AP Message Decryption Failure----
Last AP Connection Failure     ---------      Timed out while waiting for ECHO repsonse from the AP
Last Error Occurred                ---------      Lwapp join request rejected
Last Error Occurred Reason    ---------      RADIUS authorization is pending for the AP
The error reason is probaly because I haven't added AP MAC address to ACS. With the same AP, at home using ADSL link, i have no problem.
Thanks.

5508 WLC with LAG enabled

I enabled Lag on a 5508 controller. Now all the port numbers say 13. I thought they were supposed to be 29. Does this mean LAG isn't configured corecctly? Also how do you test to see that the LAG group is working correctly between the 6509 and WLC?

I'm the 5508 the lag port is 13 in the 4402 it shows as 29. The easiest way to test the lag is to shut down a port on the switch and make sure the traffic continues to flow
HTH,
Steve
Sent from Cisco Technical Support iPhone App

Building Small Network with Interconnected 2960Xs - No Connectivity

I am trying to create a network with a client connected to a 2960X, which connects to a second 2960X switch, which connects to a server. I have setup the switch connected to the client with an IP address of 10.0.1.1 for its vlan1. The second switch has an IP address of 10.0.2.1 set for its vlan1. I then interconnected the two switches using the GigabitEthernet1/0/1 interface in trunking mode on each switch. I was not able to ping the second switch, so I then configured the GigabitEthernet1/0/2 interface in access mode and connected the two switches. I am still not able to ping the second switch from either side.
What do I need to do to get this setup working? Should I be using a single VLAN that spans the two switches? Should I be using trunking or access mode for the interface that interconnects the two switches?

That is correct, each switch has only one vlan, vlan1.
Subnet mask is 255.255.255.0.
Thanks, will change all interswitch connections to trunk. Will leave all host to switch connections at access.
Unfortunately, I cannot post the output as it is from a terminal that cannot be connected to the Internet or even the Intranet and USB storage is not permitted in the area, so I cannot copy the output into a text file on a USB drive. I would have to type everything out. If there are parts of the sections of these commands that may be show the issue, please let me know and I can type up those sections.
vlan interfaces are both up.

Can this be done? Airport extreme connected wireless in extend mode to connect a wireless Mac Pro with an ethernet cable from the extended airport extreme..

Can this be done? Airport extreme connected wireless in extend mode to connect a wireless Mac Pro with an ethernet cable from the extended airport extreme.

This will work.....IF....you also have an Apple AirPort router configured to provide your wireless network.
In other words, you need to have two Apple AirPort routers to extend a wireless network.
When the AirPort Extreme is configured to "extend" the wireless of the "main" AirPort, it will provide more wireless coverage and the Ethernet ports are enabled, so you could connect your Mac Pro to any of the Ethernet ports and use that as a network and Internet connection.

HT1212 My ipod is disabled and the message requests to try again in 223004 minutes. I think it might have something to do with the date being set wrong before it went into disabled mode. Can you assist in enabling.

My ipod is disabled and the message requests to try again in 223004 minutes. I think it might have something to do with the date being set wrong before it went into disabled mode. Can you assist in enabling.

You'll need to connect it to the iTunes library you normally sync it with and restore it. If iTunes asks you for this passcode before it will let you proceed, connect the iPod to iTunes in recovery mode instead using the instructions in this Apple support document.
iOS: Unable to update or restore
B-rock

WLC 4402 LAG connection to 2 different chassis of 6509 VSS switch system

Hi,
I have inherited a 6509 VSS switch system as the network core and have the task of ensuring proper redundancy and redesign of the directly connected data center devices. One of the connected devices (WLC 4402) physically appears to be connected to both switches - the WLC is in the same rack as VSS-Chassis1 so I can trace the fiber from WLC port 1 to gi1/1/22, the other fiber from the WLC port 2 goes into the floor and presumably over to VSS-Chassis2 gi2/1/22 (there is fiber connected there, I have link lights on both sides, and the port channel, Po200, on the VSS switch which is configured on gi1/1/22 is also configured on gi2/1/22). My question pertains to the CDP neighbor output I get on the VSS switch: (truncated to include just the WLC)
NCMECHQWiFi1     Gig 1/1/22        137               H    AIR-WLC44 Gig 0/0/2
NCMECHQWiFi1     Gig 1/1/22        137               H    AIR-WLC44 LAGInterface0/3/1
NCMECHQWiFi1     Gig 1/1/22        137               H    AIR-WLC44 Gig 0/0/1
It looks like both WLC ports are physically connected to Gi1/1/22, which they are quite obviously not.
This is confirmed on the WLC's sho cdp entry all output:
(Cisco Controller) >show cdp entry all
Device ID: ncmec-vsscoresw1.ncmec.org
Entry address(es): 100.1.0.254
Platform: cisco WS-C6509-E, Capabilities: Router Switch IGMP
Interface: LAGInterface0/3/1, Port ID (outgoing port): GigabitEthernet1/1/22
Holdtime : 160 sec
I believe that the multi chassis etherchannel is set up correctly on the VSS:
vsscoresw1#sho run int gi1/1/22
interface GigabitEthernet1/1/22
description WLC-Management
switchport
switchport trunk encapsulation dot1q
switchport mode trunk
switchport nonegotiate
channel-group 200 mode on
end
vsscoresw1#sho run int gi2/1/22
interface GigabitEthernet2/1/22
description WLC-Management
switchport
switchport trunk encapsulation dot1q
switchport mode trunk
switchport nonegotiate
channel-group 200 mode on
end
vsscoresw1#sho run int po200
interface Port-channel200
description WLC-Management
switchport
switchport trunk encapsulation dot1q
switchport mode trunk
switchport nonegotiate
end
And yet when I show the details of port channel 200, I expect to see "mode on" but get instead see LACP which is unsupported on the WLC:
vsscoresw1#sho etherchannel 200 detail
Group state = L2
Ports: 2   Maxports = 8
Port-channels: 1 Max Port-channels = 1
Protocol:    -
Minimum Links: 0
                Ports in the group:
Port: Gi1/1/22
Port state    = Up Mstr In-Bndl
Channel group = 200         Mode = On      Gcchange = -
Port-channel = Po200       GC   =   -         Pseudo port-channel = Po200
Port index    = 0           Load = 0xFF        Protocol =    -
Mode = LACP
Age of the port in the current state: 180d:19h:47m:01s
Port: Gi2/1/22
Port state    = Up Mstr In-Bndl
Channel group = 200         Mode = On      Gcchange = -
Port-channel = Po200       GC   =   -         Pseudo port-channel = Po200
Port index    = 1           Load = 0xFF        Protocol =    -
Mode = LACP
Age of the port in the current state: 180d:19h:47m:02s
                Port-channels in the group:
Port-channel: Po200
Age of the Port-channel   = 354d:12h:47m:27s
Logical slot/port   = 46/19          Number of ports = 2
GC                  = 0x00000000      HotStandBy port = null
Port state          = Port-channel Ag-Inuse
Protocol            =    -
Fast-switchover     = disabled
Load share deferral = disabled
Ports in the Port-channel:
Index   Load      Port          EC state       No of bits
------+------+------------+------------------+-----------
0      FF       Gi1/1/22                 On   8
1      FF       Gi2/1/22                 On   8
Time since last port bundled:    173d:17h:06m:34s    Gi2/1/22
Time since last port Un-bundled: 173d:17h:06m:34s    Gi2/1/22
Last applied Hash Distribution Algorithm: Fixed
>>> So my question, arising at least partly from the apparently misleading CDP information, is this: How can I confirm that the WLC is correctly dual homed to both core switches? (short of tracing the cable) I ask because there are several other devices (not WLCs) that need to have the dual homed connections confirmed.
I tried a layer 2 trace route but for all macs associated with the WLC, the trace abborts with the error "Device has Multiple CDP neighbours on destination port."
Thanks in advance!
Sue

PS: It is critical that I confirm the redundancy, since as a part of the data center redesign we will be moving the second VSS chassis to the same rack with the first to simplify the dual connections. I need to verify all the redundant connections before I take it offline and move it. Thanks!

Reader X crashes after 30 secs with Protected mode enabled

Having just deployed Reader X to over 100 PC's via group policy I'm a little dishartened to find that Reader X crashes after 30 secs of being open when protected mode is enabled.
Current setup is as followed:-
Clients are XP SP3, Vista SP2 & Win7 (all crash)
Server 2003 R2 domain
Reader X deployed via MSI using GPO with a transform created using the Reader X customization wizard (only set to disable updates as I'll push these out via GPO also when available).
The problem occurs with standard domain users (doesn't happen if you use an admin account to login and run Reader X), once you disable the setting for "enable Protected mode at start up" and restart Reader X it doesn't crash. I've been reading also that the protected mode creats a sandbox environment that some AV products are currently having issues with, so I've also tested by removing my AV on a test client rebooting and running Reader X with protected mode enabled, the Pc will still crash, so that rules out my AV product.
After each crash the client logs an event in the application log
Event ID: 1000
Aource Application error
Description:
Faulting application AcroRd32.exe, version 10.0.0.396, time stamp 0x4cc5e97b, faulting module WININET.dll, version 8.0.6001.18999, time stamp 0x4ccfa98f, exception code 0xc0000005, fault offset 0x0002387b, process id 0xd54, application start time 0x01cbc2ec89ab4cba.
Anyone any ideas on why this happens?

I am seeing the same problem on Vista SP2 32-bit. I enabled the Protect Mode log and see a bunch of errors relating to registry entries. I am running Adobe Reader X 10.0.1 as a standard privilege user. The problem has been intermittent. Repeated attempts to open the same PDF will result in Adobe Reader X failing after 45 seconds, then the next attempt will work fine. I have had situations where an Adobe Reader X instance has been open for hours but a new instance crashed. I have not been able to identify any trigger that might explain the difference in behavior. The problem has gone away since disabling Protect Mode.
>>>
[05:31/19:10:43] Adobe Reader Protected Mode Logging Initiated
[05:31/19:10:43] NtCreateKey: STATUS_ACCESS_DENIED
[05:31/19:10:43] real path: \REGISTRY\MACHINE\Software\Adobe
[05:31/19:10:43] Consider modifying policy using this policy rule: REG_ALLOW_ANY
[05:31/19:10:43] NtCreateKey: STATUS_ACCESS_DENIED
[05:31/19:10:43] real path: \REGISTRY\MACHINE\SOFTWARE\Adobe
[05:31/19:10:43] Consider modifying policy using this policy rule: REG_ALLOW_ANY
[05:31/19:10:44] OpenEvent: STATUS_ACCESS_DENIED
[05:31/19:10:44] name: MSFT.VSA.COM.DISABLE.5900
[05:31/19:10:44] Consider modifying policy using these policy rules: EVENTS_ALLOW_ANY
[05:31/19:10:44] OpenEvent: STATUS_ACCESS_DENIED
[05:31/19:10:44] name: MSFT.VSA.IEC.STATUS.6c736db0
[05:31/19:10:44] Consider modifying policy using these policy rules: EVENTS_ALLOW_ANY

My macbook pro 2.0 early 2011 will not go to sleep with the power source connected. only enters sleep mode when running on battery. Someone did this happen, and it could solve?

Alo, my Macbook pro i7 2 GHz Intel Core i7 (early 2011) will not go to sleep with the power source connected. only enters sleep mode when running on battery. Someone did this happen, and it could solve?

There is no output from that command line? Maybe the pid changed.
I'll repeat what I am trying to find out...
1. You do a pmset -g on the terminal.
2. The output from that pmset should have a line that says "sleep 0 (imposed by n)" where n is some number.
3. The ps ax | grep n is supposed to display what the process associated with n is.
It's the output from step 3 that should indicate what is causing you not to sleep.
But speaking of sleep, that's where I am going.

Does anyone get the mouse lag with an external display connected via the display port?

does anyone get the mouse lag with an external display connected via the display port?

You don't describe the problem in great detail. Is this the issue you are describing?
https://discussions.apple.com/thread/4398076?start=0&tstart=0
If so, then, "Yes." I have the same problem. Note that this isn't a tracking speed problem for me, it's a lag between my hand moving and the pointer moving on the external display.
Andrew

Architecture Limitations with Replication of VM connected with Physical Mode RDM

what are Architecture Limitations with Replication of VM connected with Physical Mode RDM in vsphere replication. Why VMware is not supporting this?

vSphere Replication does not work with physical mode RDMs. This is because of the way that vSphere Replication and physical mode RDMs work.
As outlined in this: VMware KB: Difference between Physical compatibility RDMs and Virtual compatibility RDMs
It isn't currently possible for VR to do what it needs to do with physical mode RDMs.
Does this answer your question?

Why i cant watch youtube as youtube inform this "This video is unavailable with safety Mode enabled. To view this video, to need to disable safety mode" how can i turn off safety mode

Why i cant watch youtube as youtube inform this "This video is unavailable with safety Mode enabled. To view this video, to need to disable safety mode" how can i turn off safety mode
Why i cant watch youtube as youtube inform this "This video is unavailable with safety Mode enabled. To view this video, to need to disable safety mode" how can i turn off safety mode

You need to disable Safety Mode at the bottom of the YouTube page. More info here:
https://support.google.com/youtube/answer/174084?hl=en

Allow printing with protected mode enabled

Hi!
I distributed Adobe Reader XI within a GPO and I have a lot of users asking for remove the warning when they want to print the document.
With the protected mode enabled they should press the "activate all" button each time they want to print.
I know the protected mode it's for more security but this kind of bugging messages will force users to disable the "protected mode" to bypass the bugging messages, not regarding to the security issues below this.

Ok, I understand.
It seems there it's a bug in the spanish translation of Reader, because in the Enhaced Security zone it says protected mode instead of protected view on the three radios (All files, files from potentially unsafe .., Off)
Check this image:
I will look where to send this bug to Adobe.
Regards,

Low speed connection E4200 with both bands enabled

When I have both 2,4 and 5,0 GHz band enabled on the E4200 router my PC (WMP600N-PCI adapter) has max. 130Mbps.
When I enable only the 5,0 GHz band it has a speed of 270Mbps.
The same speed issue with my Dell laptop.
Router and PCI adapter are new (3 days old) and both have the latest firmware.
Both PC and laptop are running on W7.
Does someone has any idea how to increase the speed with both bands enabled?
Solved!
Go to Solution.

Thanks Expert,
The issue is indeed that with both bands enabled the PC connects on 2.4GHz and not 5GHz.
I don't know what the exact speed is but I can measure the differenses in speed between 130 Mbps and 300Mbps very good by copying files to my NAS.
I've did some more tests ans found out that two laptops in my home do the same thing. .
With both bands enabled in the router they connect at 130Mbps and with only 5 GHz it's between 240 and 300Mbps.
Could it be the router that switches off the 5GHz?
Aswel as in the router as in the wireless adapters I can not switch off one band.

WLC 5508 intermittent loss of connectivity

Hi.
I have a WLC 5508 connecting directly to a distribution switch (3850) via a layer 2 etherchannel trunk fibre link with LAG enabled on the WLC.
Whenever there is a loss of power to the server room where both devices are hosted & power later gets restored, the distribution switch & WLC lose Layer 2 & 3 connectivity. Connectivity only gets restored when the WLC is power cycled or the fibre cables connecting to its SFP ports are removed & plugged back in. When this is done connectivity is restored between them, APs associate etc. Once there is a loss of power to the room for whatsoever reason again, the loss of connectivity issue re-occurs.
Disabled the etherchannel at some point, using only a single fibre trunk link between them, but the issue persists.
Also check for interface errors, CRCs, etc on both ends but there are none.
Can anyone please advice me on what the issue is & what can be done to permanently resolve this?
Thanks in anticipation.
Ope.

Software version is 7.4.100.0
int gig1/0/5
switchport mode trunk
switchport trunk encapsulation dot1q
channel-group 1 mode on
int gig1/0/6
switchport mode trunk
switchport trunk encapsulation dot1q
channel-group 1 mode on
Port setting on the switch is set to auto-negotiate. Port setting on the controller is "auto". The link has been negotiated (& always negotiates) to 1000Mbps full duplex on both ends.
Presently in transit with no way of connecting to the device, but I checked the duplex & speed settings on both devices which was appropriately negotiated. Also checked for interface error counters on the switch, there was none. Checked the WLC logs too, there were no logs on issues with the interfaces or auto-negotiation.

WLC with LAG mode enable connected to a switch HP in LACP mode

Similar Messages

Maybe you are looking for