WLC2106 + LAP1131AG configuration help request

Greetings Everyone.
One of my customers asked me to configure a WLC 2106 and 2 LAP 1131AG (lightweight) for corporate/guest Wifi.
Basicly they want to implement a good wifi connection for internal use and a guest one with different QoS. The two lans
should both have dhcp but they must bet kept segregated so that none from the Guest wifi can access corporate resources.
Since i've never configured a WLC from scrath i lightly supposed it would be quite straigh forward as routers and switches from Cisco.
Unfortunately i was totally wrong.
I've downloaded the "Cisco Wireless LAN ControllerConfiguration Guide" (Soft.Release 6.0 June 2009) and after i red it i made up this workflow
for the configurations:
1) Configure Controller: (via serial)
     -     Set Management Interface parameters (IP- SM - Def GW - Dhcp server IP)
     -     Set Ap-Manager Interface parameters
     -     Virtual Interface parameters
     -     Set Admin Credentials
     -     Dhcp Configuration (internal and/or external)
2) Ap registration on the controller
     -     Configure vlan with dhcp request redirection to the dhcp server
3) Configure Wlan following customer's requests.
     -     Configure Wlan Auth for Corporate/Guest Wifi
     -     Configure QoS for both Wlans
Unfortunately i'm experiencing issue while trying joining the AP to the WLC.
It appers that the IT guy of my customer tried to configure one of the Ap.
In that Ap's flash i find files referring to a "mesh" configuration like:
mesh_cfg.txt - mesh_port_cfg.txt
which are not present on the other Ap.
I've tried to register both the Ap using:
1) Internal DHCP
2) External DHCP (microsoft W2k8 R2)
3) External DHCP (non cisco router)
But as a matter of fact they got the ip from dhcp but they don't show up in the WLC GUI.
So, resuming my issues sounds like:
1) Can't make Ap join the WLC
2) There are configuratin file on one Ap that i can't clear
3) DHCP configuration is probably wrong.
Since i'm quite lost, i'm ready to learn from anyone who could spare some time helping me out.
Thank you in advance!
Regards
Alessio
P.S.
Ap version is the following:
Cisco IOS Software, C1130 Software (C1130-K9W8-M), Version 12.4(21a)JHB1, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2010 by Cisco Systems, Inc.
Compiled Wed 11-Aug-10 15:39 by prod_rel_team
ROM: Bootstrap program is C1130 boot loader
BOOTLDR: C1130 Boot Loader (C1130-BOOT-M) Version 12.3(8)JEA, RELEASE SOFTWARE (fc2)

Good Day Everyone.
After a long fight, the insights of Stephen and Scott and:
https://supportforums.cisco.com/docs/DOC-13960 and
https://supportforums.cisco.com/thread/2003153
I finally managed to wipe the old configuration and to configure a LAP 1131 attached to one of the POE of the controller.
After having configured a Wlan and having set the correct DHCP redirection i'm able to connect and get an ip! (WHOA!)
I've had to set a manual ip address on the AP (let's call AP1 from now on) and to manually point it to the controller.
I was thinking about using this configuration at the customer's site getting ips from the internal DHCP and thus letting employees using the internal resources of the company.
With the same idea, i started to configure the second AP (AP2 from now on).
So i set up a dynamic interface, always on physical port 1 of the controller, gave it an ip address on another class.
Got into the antenna via console and set an ip accordingly.
I expected the controller and the antenna to communicate immediately as the AP1 did before BUT:
LWAPP_CLIENT_ERROR_DEBUG: spamHandleJoinTimer: Did not recieve the Join response
LWAPP_CLIENT_ERROR_DEBUG: No more AP manager IP addresses remain.
%SYS-5-RELOAD: Reload requested by LWAPP CLIENT. Reload Reason: DID NOT GET JOIN RESPONSE.
%LWAPP-5-CHANGED: LWAPP changed state to DOWNXmodem file system is available.
And keep reloading itself on, and on, and guess? Yes, on.
I'm sure i took a wrong step somewhere, could someone be so kind to enlighten me about it?
Thanks in advance!
Alessio

Similar Messages

RAID configuration help request

greetings
this is my current situation.
my k8n neo2 fx MOBO failled and my power blew up, so i had a replacement mobo and power.
i flashed the mobo to the latest firmware 1.C and continued configuring my system.
in my previous installation, i had my two western digital running on the MOBO raid with winxp sp2 + all hotfixes
i attempted to configure the raid with the same settings,
- enabled the raid device & selecting the disks that are made visible to the raid chips.
- made sure that the disks are found on boot (setting to auto thou when configuring the raid it always sets the disks to none having to set it back to auto, a bios bug that hasnt been fixed at least since version 1.9)
- made sure that the raid device is selected in the disk boot order
- recreated the raid array and made sure that it is bootable (pressing B)
now the issue is that when i hav ethe mentioned raid configuration in place, the raid does not boot
i get that disk not found ctrl-alt-del
but when i turn of the raid chip feature from the bios and boot of the first disk, it boots fine but runs lously since the
raid service deamon fails :P
any ideas on how this can be resolved? ive banged my head with this all day and i dont want to reinstall my **** OS :(
regards
Matice

i did brake and recreate the raid (not wiping the data of course ) but it didnt help, though i didnt try reordering the disks,
ill give that a try now.
as i said, when i disable the raid, the disk boot winxp fine, but xp is acting all bizare propably due to the failiure of the
raid service not running since the raid has been disabled..
Quote from: BOSSKILLER on 30-December-06, 03:13:17
can you boot from alternative location to see array is correctly assigned(etc: all data is there and so on...)
broke array and re-create it, but reverse HDD's position in array by adding into array. (1st, become 2nd, and 2nd become 1st)
re-test.

ACS Group Configuration Help Request

We currently have an underutilized ACS server and are trying to 'secure' more of our devices and the network in general utilizing the ACS 4.0 we have.
The problem, and I'm guessing it's a simple resolution, is that currently we have a Group called Remote_Access for vpn/citrix. It is mapped to an external database (Active Directory) group namped Remote_Access. Everything works fine there. The problem I'm having is, I created another group in ACS further down the list for TACACS_ADMIN. We also have this group mapped to an AD group called TACACSADM. However, it seems that due to the fact that I personally am a member of both RemoteAccess and TACACSADM, whenever I try to authenticate to a switch, it shows me hitting the RemoteAccess group.. not TACACS ADMIN. How do I tell the groups to ignore requests unless it comes from a certain AAA client? I tried doing a Define IP Based Restrictions and selecting the AAA NG that it could come from, but all that did was give me a 'user filtered' in the failed attempts log for RemoteAccess. Isn't there some way to have it skip the Remote Access group and go on to TACACS Admin group?
Confusing I know.

Hello,
you can solve your problem with the feature Network Access Profile. With this feature you can assign one user to different groups.
You must create two Network Access Profiles (profile_remote_access, profile_tacacs_admin)-
with different protocol types (radius for remote access, tacacs for administration).
Look at
http://www.cisco.com/en/US/products/sw/secursw/ps5338/products_user_guide_chapter09186a00805e879e.html
regards
alex

Help me configure Change request management !!!

Dear friends,
I am Going to Configure Change request Management, so just to ensure that the configuration is not erronous, i would need Expert advise..
Just want to know Clear few things before i proceed..
I am also refering SPRO and related notes
Scenario :
I have two SYSTEMS SAP ECC 6.0 with System id R03 and Soluiton manager with SYSTEM id SOL,
R03 has 3 clients, 300 600 700..
In R03 300 is the development client, 600 is quality client, 700 is the production client.
SOL has 2 clients, 100, 200
With 200 as the production client.
Q.1) Do i have to configure CHARM in both the client (100 and 200 of SOLMAN).
Q.2) Initially I had tried to set CHARM in client 100 of solman, but later on realized that it has to be set up in client 200.
When i logon to client 200 and Execute IMG activity Spro-> sap soltion manger->basic settings-> sap solution manager system->activate integration with change request management.
Then by default it take the previous client ( client 100) as the change request management client.
( as we know there are three steps in the above activity ), the other activity are executed properly, only prblem being that the default client is always set to 100, which should not be the case).
I do get the prompt saying ( "The change request clent is set to clent 100, do u want to change to client 200, on clicking yes, still it is always set the same client 100 as charm client ")
Plz let me know what do i do to set the change request client to 200??
Q.3) Regarding TMS, we have local domain controller in solman and local domain in R3.
We are planing to establish domain links between the two systems( ie both the domain controllers) ??
Is this the right strategy ??
Any other method that u can recommend ??
Q.4)One of the IMG activity says, Generate Destinations to client 000 of all the domain controllers..
Whenever i do this these, destinations are created with errors, i am not able to create trusted RFC destinations without errors.
When i logon to satellite domain controler and excecute sm59 there are 2 destinations created Trusted and BACK.
These destinations works well,
but when i logon to Solman, got to sm59 , when i test the TMW and TRUSTED rfc destinations i test these destinations using Remote Logon i get error,
" no authorization to logon as trusted system"
I went thru one note which recomended Kernel upgrades to solve the problem,
I r3 my kernel relaese is 700 with patch level 56, the note recomends to apply patch 80, did u have these problems??
what is your kernel patch levels in sateliite and solman systems.
Q.5) TO be able to raise tickets from R3 to solman we create RFC destinations.
We also create RFC destinations to client 000 of all the sateliite system,
dont u think these RFC destinations might interfere with each other??
Q.6) Is there anyone who has successfully configured CHARM. Can you plz share the configuration documents with me..
Please note :
All the contributors would be handesomely rewarded with points .

Hi,
Check this
Note 128447 - Trusted/Trusting Systems
For your Q4.
Q3.)
Establishing Domain link - That's the right way. Go ahead.
These are the steps.
1.Define Transport Routes for System Landscape
assign exactly one development system to a production system, and that these two systems are connected by exactly one unique transport track. If a development system and a production system are connected by more than one transport track, this may lead to inconsistencies within the transport distribution. This type of transport configuration cannot be supported by Change Request Management, and may cause inconsistencies within the tools involved.
2. Activate Extended Transport Control
The CTC parameter should be '1'
3.Configure Transport Strategy
Deactivate the QA Approval.
4. Activate Trusted Services.
5.Activate Domain Links.
You have to activate domain link between systems.
6. Generate RFC Destinations to Client 000
Hope this helps.
feel free to revert back.
--Ragu

The RADIUS request did not match any configured connection request policy (CRP)

I setup NPS server and added a RADIUS Client access point, my project is to get a wireless user to authenticate using his/her AD credientials, my problem is i can't seem to authenticate my user
my NPS server is giving me this error log under Event Viewer > Server Logs > Network Policy and Access Services
    Reason:                The RADIUS request did not match any configured connection request policy (CRP).
but from my understanding i don't need to setup Connection Request Policies because i am using Network Policy
Please Help!

thanks for your reply, i setup a new NPS policy here is my error log
Network Policy Server denied access to a user.
Contact the Network Policy Server administrator for more information.
User:
    Security ID:            NULL SID
    Account Name:            csdomain\rsingh
    Account Domain:            csdomain
    Fully Qualified Account Name:    csdomain\rsingh
Client Machine:
    Security ID:            NULL SID
    Account Name:            -
    Fully Qualified Account Name:    -
    OS-Version:            -
    Called Station Identifier:        0026.992f.6761
    Calling Station Identifier:        2477.0392.b0f8
NAS:
    NAS IPv4 Address:        192.50.2.2
    NAS IPv6 Address:        -
    NAS Identifier:            MYWAP
    NAS Port-Type:            Wireless - IEEE 802.11
    NAS Port:            35290
RADIUS Client:
    Client Friendly Name:        MYWAP
    Client IP Address:            192.50.2.2
Authentication Details:
    Connection Request Policy Name:    PEAP
    Network Policy Name:        -
    Authentication Provider:        Windows
    Authentication Server:        MYSERVER.csdomain.com
    Authentication Type:        EAP
    EAP Type:            -
    Account Session Identifier:        -
    Logging Results:            Accounting information was written to the local log file.
    Reason Code:            22
    Reason:                The client could not be authenticated because the Extensible Authentication Protocol (EAP) Type cannot be processed by the server.

AT selection-screen on ON HELP-REQUEST

Hi
What is normally done in the Selection Screen event :
AT selection-screen on ON HELP-REQUEST.
Normally pressing F1 helps gives Documentation present in Data Element assoicated with the field. Exactly in what cases would we be needing to use this event.

Hi,
That event is used for search.
at selection-screen on value-request for p_file.
call function 'F4_FILENAME'
       exporting
            field_name = 'p_file'
       importing
            file_name = p_file.
If you code in the same manner in the selection screen you will able to search and select a file from your work station, so that it will be uploaded in SAP.
I hope this will help you, if not plzzz be back.
CHEERS
If your problem is solved award points and close the thread.

PROCESS ON HELP-REQUEST

Hi
wat is importance of POH. what If there is no PROCESS ON HELP-REQUEST ?
Thanks and regards
- Puneet Sharma.

To display data element supplement documentation, you must code the following screen flow logic in the POH event:
PROCESS ON HELP-REQUEST.
FIELD <f> [MODULE <mod>] WITH <num>.
After PROCESS ON HELP-REQUEST, you can only use FIELD statements. If there is no PROCESS ON HELP-REQUEST keyword in the flow logic of the screen, the data element documentation for the current field, or no help at all is displayed when the user chooses F1. Otherwise, the next FIELD statement containing the current field <f> is executed.
If there is screen-specific data element supplement documentation for the field <f>, you can display it by specifying its number <num>. The number <num> can be a literal or a variable. The variable must be declared and filled in the corresponding ABAP program.
You can fill the variables, for example, by calling the module <mod> before the help is displayed. However, the FIELD statement does not transport the contents of the screen field <f> to the ABAP program in the PROCESS ON HELP-REQUEST event.

1941W configuration help needed

Our Deployment Scenario:-
1941W Gigabit Ethernet 0/0 is connected to the PPOE connection of the ISP.
Gigabit Ethernet 0/1 is connected to the wired LAN
I have created 2 wireless radio Cisco_Kamran_BGN which is operating at 2.4 Ghz Devices and Cisco_Kamran_A which is operating at 5Ghz Devices.
I have created 2 VLans for the Wireless.
Vlan 10 for Cisco_Kamran_A        192.168.10.x
Vlan 11 for Cisco _Kamran_BGN   192.168.11.X
The problem is the Wireless users are not getting the IP address from the respective DHCP server which has been configured on the Router.
Can please any from the community help me and show me where I am missing the configuration.
Please find my router & ap configuration below.
Router Configuration
Router#
sh run
Building configuration...
Current configuration : 3022 bytes
! No configuration change since last restart
version 15.1
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname Router
boot-start-marker
boot-end-marker
enable secret 5 $1$TdQt$npYeaf/W0kRElcfMggzJ31
no aaa new-model
service-module wlan-ap 0 bootimage autonomous
no ipv6 cef
ip source-route
ip cef
ip dhcp excluded-address 192.168.1.1 192.168.1.50
ip dhcp excluded-address 192.168.10.1 192.168.10.10
ip dhcp excluded-address 192.168.11.1 192.168.11.10
ip dhcp pool DHCP
network 192.168.1.0 255.255.255.0
default-router 192.168.1.1
dns-server 195.229.241.222 213.42.20.20
ip dhcp pool Cisco_Kamran_A
network 192.168.11.0 255.255.255.0
default-router 192.168.11.1
dns-server 195.229.241.222 213.42.20.20
ip dhcp pool Cisco_Kamran_BGN
network 192.168.10.0 255.255.255.0
default-router 192.168.10.1
dns-server 195.225.241.222 213.42.20.20
multilink bundle-name authenticated
crypto pki token default removal timeout 0
license udi pid CISCO1941W-E/K9 sn FCZ1553C1VK
hw-module ism 0
redundancy
bridge irb
interface Embedded-Service-Engine0/0
no ip address
shutdown
interface GigabitEthernet0/0
ip address 192.168.1.1 255.255.255.0
ip nat inside
ip virtual-reassembly in
duplex auto
speed auto
interface wlan-ap0
description Service module interface to manage the embedded AP
ip unnumbered GigabitEthernet0/0
arp timeout 0
no mop enabled
no mop sysid
interface GigabitEthernet0/1
no ip address
duplex auto
speed auto
pppoe enable group global
pppoe-client dial-pool-number 1
interface Wlan-GigabitEthernet0/0
description Internal switch interface connecting to the embedded AP
switchport mode trunk
no ip address
interface Vlan1
no ip address
interface Vlan10
ip address 192.168.10.1 255.255.255.0
ip access-group DSL_ACCESSLIST in
ip nat inside
ip virtual-reassembly in
interface Vlan11
ip address 192.168.11.1 255.255.255.0
ip access-group DSL_ACCESSLIST in
ip nat inside
ip virtual-reassembly in
interface Dialer1
ip address negotiated
ip nat outside
ip virtual-reassembly in
encapsulation ppp
dialer pool 1
ppp authentication pap callin
ppp pap sent-username xxxxxx password 0 xxxxxx
ppp ipcp route default
ip forward-protocol nd
no ip http server
no ip http secure-server
ip nat inside source list DSL_ACCESSLIST interface Dialer1 overload
ip access-list extended DSL_ACCESSLIST
permit ip 192.168.0.0 0.0.255.255 any
control-plane
line con 0
password xxxxxx
login
line aux 0
line 2
no activation-character
no exec
transport preferred none
transport input all
transport output pad telnet rlogin lapb-ta mop udptn v120 ssh
stopbits 1
line 67
no activation-character
no exec
transport preferred none
transport input all
transport output pad telnet rlogin lapb-ta mop udptn v120 ssh
line vty 0 4
password xxxxxx
login
transport input all
scheduler allocate 20000 1000
end
Router#
Router#
Router#
Access Point Configuration
ap#
ap#
ap#
sh run
Building configuration...
Current configuration : 2603 bytes
version 12.4
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
hostname ap
enable secret 5 $1$JxdQ$a2/00bWJuhUKP9QLC94YD/
no aaa new-model
dot11 syslog
dot11 ssid Cisco_Kamran_A
   authentication open
   authentication key-management wpa
   guest-mode
   wpa-psk ascii 7 1045081417161C5A555C7A7B
dot11 ssid Cisco_Kamran_BGN
   authentication open
   authentication key-management wpa
   guest-mode
   wpa-psk ascii 7 020D05561907017015165949
username Cisco password 7 14341B180F0B
bridge irb
interface Dot11Radio0
description 802.11bgn radio
no ip address
no ip route-cache
encryption mode ciphers aes-ccm
broadcast-key change 3600
ssid Cisco_Kamran_BGN
antenna gain 0
station-role root
bridge-group 11
bridge-group 11 subscriber-loop-control
bridge-group 11 block-unknown-source
no bridge-group 11 source-learning
no bridge-group 11 unicast-flooding
bridge-group 11 spanning-disabled
interface Dot11Radio1
description 802.11a radio
no ip address
no ip route-cache
encryption mode ciphers aes-ccm
ssid Cisco_Kamran_A
antenna gain 0
no dfs band block
channel dfs
station-role root
bridge-group 10
bridge-group 10 subscriber-loop-control
bridge-group 10 block-unknown-source
no bridge-group 10 source-learning
no bridge-group 10 unicast-flooding
bridge-group 10 spanning-disabled
interface GigabitEthernet0
description the embedded AP GigabitEthernet 0 is an internal interface connecting AP with the host router
no ip address
no ip route-cache
bridge-group 1
no bridge-group 1 source-learning
bridge-group 1 spanning-disabled
interface GigabitEthernet0.10
description 802.11a bridge
encapsulation dot1Q 10
no ip route-cache
bridge-group 10
bridge-group 10 subscriber-loop-control
bridge-group 10 block-unknown-source
no bridge-group 10 source-learning
no bridge-group 10 unicast-flooding
bridge-group 10 spanning-disabled
interface GigabitEthernet0.11
description 802.11bgn bridge
encapsulation dot1Q 11
no ip route-cache
bridge-group 11
bridge-group 11 subscriber-loop-control
bridge-group 11 block-unknown-source
no bridge-group 11 source-learning
no bridge-group 11 unicast-flooding
bridge-group 11 spanning-disabled
interface BVI1
ip address dhcp client-id GigabitEthernet0
no ip route-cache
ip http server
no ip http secure-server
ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
bridge 1 route ip
line con 0
no activation-character
line vty 0 4
login local
end
ap#
ap#
ap#

Hi Stepehen,
Did the configuration as per your advice but i am getting the below mentioned error which i have highlighted it in red. Please advice what needs to be done.
Home
Re: 1941W configuration help needed
created by Stephen Rodriguez in Getting     Started with Wireless - View the full discussion
conf t
interface     Dot11Radio0
no ssid     Cisco_Kamran_BGN
no encryption mode     ciphers aes-ccm
exit
interface     Dot11Radio1
no encryption mode     ciphers aes-ccm
no ssid     Cisco_Kamran_A
exit
dot11 ssid     Cisco_Kamran_A
vlan 10
dot11 ssid     Cisco_Kamran_BGN
vlan 11
exit
interface     Dot11Radio0
encryption vlan 11     mode ciphers aes
ssid     Cisco_Kamran_BGN
exit
interface     dot11radio0.1
encapsulation     dot1q 1 native
bridge-group 1
interface     dot11radio 0.11
encapsulation     dot1q 11
bridge-group 11
Configuration of     subinterfaces and main interface
within the same bridge     group is not permitted
exit
interface     Dot11Radio1
encryption vlan 10     mode ciphers aes-ccm
ssid     Cisco_Kamran_A
interface     dot11radio1.1
encapsulation     dot1q 1 native
bridge-group 1
interface     dot11radio1.10
encapuslation     dot1q 10
bridge-group 10
Configuration of subinterfaces and main     interface
within the same bridge     group is not permitted
end
wr
Reply to this message by going to Home
Start a new discussion in Getting Started with Wireless at Home

Process on Help request and Process on value request events examples

HI All,
Can anybody please give me some examples of Process on Help request and Process on value request events.
Thanks in advance

HI,
Check programs
demo_selection_screen_f1.
demo_selection_screen_f4.
Regards,
Sesh

Need configuration help on producing dial tone

Hello Experts,
I have a Cisco 2921 router with VWIC3-2MFT-T1/E1 card. On this card we have T1-CAS digital line connected. We have been provided with a set of DID numbers. We have a requirement where, when we dial a DID, the router should provide a dial tone, and should allow the user to dial to extension numbers. Not sure if this is feasible. If at all possible, will need to some configuration help.
Thanks
Arabinda

Sure it's possible. What's the T1 connected to? The router will offer two-stage dialing (aka dial tone) when the incoming POTS dial-peer does not have the 'direct-inward-dial' command on it. The router will accept any input and search for an outbound dial-peer (or ephone-dn for locally registered DNs) to match. Be careful if the T1 is connected to the PSTN as this is a toll fraud risk. You need to use CoR to reign in what outbound dial-peers are available to it.
Dial Peer Basics:
http://www.cisco.com/en/US/tech/tk652/tk90/technologies_tech_note09186a008010ae1c.shtml
Class of Restrictions:
http://www.cisco.com/en/US/tech/tk652/tk90/technologies_configuration_example09186a008019d649.shtml
Please remember to rate helpful responses and identify helpful or correct answers.

DCOM was unable to communicate with the computer xyz using any of the configured protocols; requested by PID 7b28 (C:\Program Files\Microsoft\Exchange Server\V15\Bin\MSExchangeHMWorker.exe).

Hi,
Previously I've two exchange server 2013 named : ABC and XYZ. After is decomm XYZ, i got this error :
DCOM was unable to communicate with the computer XYZ using any of the configured protocols; requested by PID 7b28 (C:\Program Files\Microsoft\Exchange Server\V15\Bin\MSExchangeHMWorker.exe).
EventID:10028
Source:DistributedCOM
May I know the reason why the server keep looking for the non-exist server and how to terminate this process?
Thanks in advance.

Hello,
It seems that error message occurs on the same machine with the previous Exchange Server you have decommissioned. Have you reinstall the Windows System after uninstall the Exchange
Server?
You need to check the registry keys but this is not efficient solution. The most efficient way is to reinstall the Windows if it is convenient.
Thanks,
Simon Wu
TechNet Community Support

Multiple ethernet network adaptors + MySQL/php5: configuration help needed

I would be grateful if someone could give me some advice on how to configure multiple ethernet adapters under OS X 10.5.6
I have set up my system to work nicely with two ethernet network adapters, each with its own fixed IP. This bit works just fine. The machine supports two separate servers - a mail server and the OS X Apache2 server. I have configured the mail server to only listen to one of the IPs, and the Apache2 server to listen to the other (via httpd.conf). The system also has MySQL and php5 installed / enabled, and these services are only used by the Apache2 server.
The problem I have is that when I start the machine, initially the php5 system cannot connect reliably to the MySQL database system. The fix I have found is to temporarily make the ethernet adapter connected to the mail server 'inactive'. While this is so, the php5/MySQL connection to Apache2 works. Curiously, once an initial connection between php5 and MySQL has been made, subsequently I can make the mail server's ethernet adapter active again without further problems.
I initially thought this might be due to 'service order' issues - but changing the service order (e.g. putting the Apache adapter 'above' the mail adapter in the service order does not help. The fix only works by making the mail adapter inactive temporarily.
I suspect that there is some configuration change I can make to clarify the setup I have. The MySQL and Apache installations only need to talk to the Apache server - but I am not sure how to record this configuration in the OS X system.
Thanks in advance for any assistance that you can provide.
Message was edited by: Gavin Lawrie

Hi Stepehen,
Did the configuration as per your advice but i am getting the below mentioned error which i have highlighted it in red. Please advice what needs to be done.
Home
Re: 1941W configuration help needed
created by Stephen Rodriguez in Getting     Started with Wireless - View the full discussion
conf t
interface     Dot11Radio0
no ssid     Cisco_Kamran_BGN
no encryption mode     ciphers aes-ccm
exit
interface     Dot11Radio1
no encryption mode     ciphers aes-ccm
no ssid     Cisco_Kamran_A
exit
dot11 ssid     Cisco_Kamran_A
vlan 10
dot11 ssid     Cisco_Kamran_BGN
vlan 11
exit
interface     Dot11Radio0
encryption vlan 11     mode ciphers aes
ssid     Cisco_Kamran_BGN
exit
interface     dot11radio0.1
encapsulation     dot1q 1 native
bridge-group 1
interface     dot11radio 0.11
encapsulation     dot1q 11
bridge-group 11
Configuration of     subinterfaces and main interface
within the same bridge     group is not permitted
exit
interface     Dot11Radio1
encryption vlan 10     mode ciphers aes-ccm
ssid     Cisco_Kamran_A
interface     dot11radio1.1
encapsulation     dot1q 1 native
bridge-group 1
interface     dot11radio1.10
encapuslation     dot1q 10
bridge-group 10
Configuration of subinterfaces and main     interface
within the same bridge     group is not permitted
end
wr
Reply to this message by going to Home
Start a new discussion in Getting Started with Wireless at Home

Quick upload not configured Help

Quick upload not configured Help Why and how do I configure? Host ?, username, password?

I have exactly the same question, using almost the same system: MacBook Pro, OS X Mountain Lion (10.8.3).
What to do? I cannot find an answer for how do I configure? Host, Username? Password?

IDOC Configuration Help

hello,
i have just started learning concepts of IDOC and ALE.
And found some docuemnts for the same.
WE have 2 clients in our dev server. 700 & 600.
I want to test idoc concepts on these clients of same servers.
Firstly i checked logical systems on client 700.
Have a look.
here 600 client is not shown but it exists in our system.
Moreover , 400 client is shown..but it does not exists in our system.
Here is the view of table T000
Please tell me...what this is all about.
Whether i need to create a new logical system or assign client to existing logical system
or nothing.In order to run idoc's?

Hi Abhishek,
Refer the steps below and let me know if it helped.
ALE configuration normally involves the seven basic steps which are:
1. Creating users for ALE Transfer
2. Creating Logical system and assign the client
3. Creating the RFC
4. Configuring Distribution Model
5. Configuring and checking the port
6. Configuring and checking the partner profile
7. Creating the message type
The steps to configure and use it is mentioned below:
Notes: 105 is Sender and 800 Receiver System in the example below:
1. Create Users for ALE transfer in both receiving and sending client/systems.
Create users in both the client/systems giving the same user name and proper authorizations. We need to use these user ids to logon through the remote connection and perform the IDOC transfers.
2. Creating Logical Systems
o       Create logical systems for both sending and receiving systems in both systems.
o       Login to Client 105 (SENDER)
o       Go to T. Code SALE
o       Expand Sending and Receiving Systems
o       Expand Logical Systems
o       Click on Define Logical System
o       Click on New Entries
o       Create Logical Systems with naming convention 'system name'+'CLNT'+client no . For example for sending system ex: SSPCLNT105
o       Create Logical Systems with naming convention 'system name'+'CLNT'+client no ex: example for receiving system ex SEDCLNT800
o       Save and come back
o       Click on Assign client 105 to Logical system SSPCLNT105
o       Now, logon to client 800, repeat the same above process to create logical systems SEDCLNT800 and SSPCLNT105
o       Save and come back
o       Click on Assign client 800 to Logical system SEDCLNT800
3. Creating the RFCs
o       In client 105, Go to T. Code SM59
o       Expand R/3 Connections
o       Enter RFC Name as SSPCLNT105 (give this name same as that of logical name created in step1 so that the ports are automatically created)
o       Connection Type as 3
o       Language as EN
o       Give the logon details for client 800 (usually, we create a new user with proper authorizations for this ALE data transfer)
o       Click on Remote logon button to test the RFC
o       Now, go to client 800 and repeat the same process to create the RFC connection to client 105, giving logon credentials to client 105
4. Creating Customer Distribution Model
(we usually create this in the original system(sending system) and then distribute it to other systems. The actual creation of the model requests that you mention a technical name for the model (unique identifier in the systems landscape), a sender system, a receiver system and message types to exchange between those systems.)
o In Client 105, Go to T. Code BD64
o       Click on change and Create model view button
o       Enter the short text and Technical name as ZSSP_SED
o       Select the model and click on Add Message Type Button,
o       Give the Sender as SSPCLNT105, Receiver as SEDCLNT800,
o       Give Message type as required, Ex: 'HRMD_A' for HR Module.(usually Message types given by SAP are available for a particular module, see this using tcode WE81, if not create a message type first)
o       Note: If we are performing this data transfer task for all modules at a Customer site, then we will need to use the appropriate message type and create a new Distribution model.
o       Select the above model view and click on Environment -> Generate Partner Profiles
o       Select Transfer IDOC Immediately and Trigger Immediately radio buttonsF
o       Click on Execute
o       You should get a list in green color which means it executed successfully.
o       Back to main screen, select the model view
o       Click Edit->Model view->Distribute
o       Click on continue
o       You should get a list saying model view is distributed successfully.
5. Checking the Port
o       In client 105, Go to T. Code WE21
o       Expand Transactional RFC
o       Find the port from the list which is created using BD64 for SEDCLNT800 (Receiving system) RFC Destination.
6. Checking the Partner Profiles.
o       In client 105, Go to T. Code WE20
o       Expand Partner Type LS
o       Select the Partner profile SEDCLNT800
o       Double click on Message Type (For Ex: In HR Module, HRMD_A in Outbound parameters.)
o       Check Receiver Port is assigned correctly
o       Check the Basic type as your Basic IDOC object.
o       In the sending system, select the option to transfer IDOCs immediately.
o       By default, in the receiving system IDOCS are bunched together and received.
7. Creating the Message Type
o       Message type defines the 'meaning' of data. It is just a logical entity that gets connected to the Idoc type (in tcode we82) or gets connected to the distribution model (in tcode BD64)
o       If necessary create a new message type. In client 105, go to tcode we81.
o       Click on change, continue
o       Click on New Entries button
o      Give message type in customer namespace Z* and description
o     Save and back
This should be helpful for ALE configurations.
Thanks,
Anupam

Help Requested - Agents/Scheduler/Bursting Mode/

Hello,
I have OBIEE 11G.
I have an automated email bursting requirement.
The details are -
I have one Table of people's names, address, email id and personal details. These people are not intended to be OBIEE users.
It is a table with people's names and email id.
Using each person's id(Pri key), I want to create a personalized email message and send it out to the intended email.
Sample rows-
Name: Vikram, Address: 123 abc st, Email: [email protected]
Name: Ram, Address: 345 xyz st, Email: [email protected]
message would be
Hello <vikram>
<Addr: 123 abc st>
Welcome!
Thanks
And it has to be sent to the email [email protected]
(( I'm researching more on using the SA system table .. but I really do not want to create them as OBIEE users.))
I want help in terms of what would be the best way to do that. I need direction to look into.
Further action:
Each time a new user is added to the table - the personalized email should be sent to that member. ((Maybe use flags??)
(I was thinking in terms of Triggers - & is there a way to use scripting for scheduling agents? command line?)
Please ask more details and I can answer them for help.
Thanks
Vikram

Hi! Thanks for the reply,
After much googling we've finally found a stable configuration.
java.args=-server -Xmx768m -Xss64k -Dsun.io.useCanonCaches=false -XX:MaxPermSize=512m -XX:+UseParallelGC -Dcoldfusion.rootDir={application.home}/ -verbose:gc -Xloggc:c:/Jrun4/logs/gc/gcInstance1b.log
I tried playing with the survivor ratio but came back to the default when I didn't notice much improvement. In the end what did it (pretty sure) is -Xss to reduce the requests size living on the stack. Our large initial heap, perm + overhead combined with the default request size was causing the JVM to go over and blow up I think.
We've been stable for over a month now, the next step for us is to reduce the MaxPermSize a little at a time to find our optimal range.

WLC2106 + LAP1131AG configuration help request

Similar Messages

Maybe you are looking for