WLC5508 with LAP1142N ignoring Radio Policy

Hi..
I've got a weird problem with the WLC5508 and LAP1142Ns..
We have a few WLANs using all radios.. And also one that is set to only use 802.11g.. however.. a lot of clients using that WLAN are shown as using 802.11a for connection.. (Apple iPad2 devices).. some use g, but most of them go in with a.
why?
I tried rebooting the iPad.. turning off and on the WiFi.. resetting the LAP that it was connected to.. resetting the Networksetting on the iPad..
all the things I could think of where a dormant setting might have hidden..
it just doesn't care.. always in the client list with protocol 802.11a...
help.. I want the iPads on g...
Thank you..
Thomas

Hi
I decided to create the same set up with 1131 and 1141 and found no problem connecting with the specified radio type. My controller is also on 7.2.103. Please take a look below. In my opinion probably there is an issue with 1142 APs, which is strange as the AP downloads its code and WLAN config from the Controller. Secondly, I would suggest that you take a look at the wireless adapter configuration of the client to ensure that it's radio type is set to Auto and not default to dot11a, b, or g.
(Cisco Controller) >show sysinfo
Manufacturer's Name.............................. Cisco Systems Inc.
Product Name..................................... Cisco Controller
Product Version.................................. 7.2.103.0
Bootloader Version............................... 1.0.1
Field Recovery Image Version..................... 6.0.182.0
(Cisco Controller) >show wlan 2
WLAN Identifier.................................. 2
Radio Policy..................................... 802.11g only
(Cisco Controller) >show client summary
Number of Clients................................ 21
MAC Address       AP Name           Status        WLAN/GLAN/RLAN Auth Protocol         Port Wired
00:1f                    xx-03             Associated   2              Yes 802.11g          13   No
Would you like to display more entries? (y/n)
(Cisco Controller) >show ap config general xx-03
AP Model......................................... AIR-LAP1141N-E-K9
(Cisco Controller) >show client summary
Number of Clients................................ 22
MAC Address       AP Name           Status        WLAN/GLAN/RLAN Auth Protocol         Port Wired
00:1f                  AP0007.xxx.xx04 Associated    2              Yes 802.11g          13   No
(Cisco Controller) >show ap config AP0007.xx.xx04
AP Model......................................... AIR-LAP1131AG-E-K9
(Cisco Controller) >show wlan 2
WLAN Identifier.................................. 2
Radio Policy..................................... 802.11a only
(Cisco Controller) >show client summary
Number of Clients................................ 24
MAC Address       AP Name           Status        WLAN/GLAN/RLAN Auth Protocol         Port Wired
00:1f:xx         AP0007.xxxx.xx04 Associated    2              Yes 802.11a         13   No
00:40:xx        AP0007.xxxx.xx04 Associated    2              Yes 802.11a          13   No

Similar Messages

Invoke a business service base in a WSDL with customer WS-Security Policy

Customer write a Web service (Refer to the attachment file “HTTPS_PartyServicePortType.WSDL”)which declare a WS-Security Policy and apply this it to WS binding ,How can I generate a business service base in this WSDL and invoke it successfully?
When create a business service in OSB, we get a error with below messages
[[OSB Kernel:398133]The service is based on WSDL with Web Services Security Policies that are not natively supported by Oracle Service Bus. Please select OWSM Policies - From OWSM Policy Store option and attach equivalent OWSM security policy. For the Business Service, either you can add the necessary client policies manually by clicking Add button or you can let Oracle Service Bus automatically pick and add compatible client policies by clicking Add Compatible button.
After enhanced the OSB domain with OWSM extension, we found the OOTB OWSM defined cannot support the HttpsToken and OSB cannot support below WS-Policy defined in OWSM, refer to http://docs.oracle.com/cd/E21764_01/doc.1111/e15866/owsm.htm#OSBDV1681
51.2.8.1 Unsupported Assertion
•     binding-permission-authorization
•     http-security
•     OptimizedMimeSerialization (MTOM)
•     RMAssertion (Reliable Messaging)
•     sca-component-authorization
•     sca-component-permission-authorization
•     UsingAddressing
•     wss-saml-token-bearer-over-ssl (Authentication)
it means that we cannot generate a web service with customer WS-security Policy
The WS-Security Policy is shown as below:
<wsp:Policy wsu:Id="WSHttpBinding_IPartyServicePortType_policy">
<wsp:ExactlyOne>
<wsp:All>
<sp:TransportBinding xmlns:sp="http://schemas.xmlsoap.org/ws/2005/07/securitypolicy">
<wsp:Policy>
<sp:TransportToken>
<wsp:Policy>
<sp:HttpsToken RequireClientCertificate="false"/>
</wsp:Policy>
</sp:TransportToken>
<sp:AlgorithmSuite>
<wsp:Policy><sp:Basic256/></wsp:Policy>
</sp:AlgorithmSuite>
<sp:Layout><wsp:Policy><sp:Strict/></wsp:Policy></sp:Layout>
</wsp:Policy>
</sp:TransportBinding>
<wsaw:UsingAddressing/>
</wsp:All>
</wsp:ExactlyOne>
</wsp:Policy>
BestRegards!
Simon

Hi
According to
http://e-docs.bea.com/wls/docs90/webserv/annotations.html#1050414
If you are going to publish the policy file in the Web Service archive, the policy XML file must be located in either the META-INF/policies or WEB-INF/policies directory of the EJB JAR file (for EJB implemented Web Services) or WAR file (for Java class implemented Web Services), respectively.
Can you make sure the policy file is in there?
Also there is a sample from the developer at http://dev2dev.bea.com/blog/jlee/archive/2005/09/how_to_use_anno.html
Vimala-

LDAP (openldap) authorization with DAP (dymamic access policy)

Hello,
We have a asa 5520 and we try to make a ldap (openLdap) authorization with DAP (Dynamic Access Policy). We have problem with logical expression. We need more example of logical expression and we need to know how debug logical expression. We try to use de Debug dap trace and debug dap error but we need more debug informations.

Hi
I guess you are using an ldap attribute map, to map the ad group to a group policy. This does not work as you may expect when the user is part of multiple groups, I.e. the user will always be mapped to the same group (first or last in the list, not sure).
Possible solution : remove the ldap attribute map, and configure dap rules that check the ldap.memberOf attribute instead
Hth
Herbert
Sent from Cisco Technical Support iPad App - sorry for the brief explanation, if you need more details let me know.

Pair iPhone with alpine car radio

My iPhone 5 won't pair with the Alpine radio in my car. The iPhone 4 did it with no problems.

I have an Alpine CDE-103BT, had an iphone 4 paired to it. When I got my iPhone 5 I couldn't get it paired. It saw the unit but using 0000 failed each time even though the Alpine manual said to use it and that worked with the iPhone 4. I bought the Stereo at Crutchfield which has lifetime support for anything you get from them. After several hours of searching and reading forums I broke down and called Crutchfield. Supplied my order number and explained what was happening. They told me even though the maunal say use 0000 , try 1234 . Did 1234 and I now have the iPhone5 paired to my Alpine.

XPERIA with integrated DAB+ radio

When will there be XPERIAs with integrated DAB+ radio available in Europe? For iOS there are at least accessories available. I would prefer to have built in DAB+. SONY has released DAB+ tuners in compact Hifi sets and in portable radios. Given that DAB+ is primarily targeted at mobile reception it seems weird that DAB+ is not available cell phones. It would also be a great way to differentiate the product given that other vendors do not have solutions at this point. For the UK it seems an imperative to have at least DAB included, for Germany DAB+ tuners would certainly raise awareness of teh XPERIA brand among younger people...
So when will there be XPERIAs with DAB+ (would like to have it with LTE in one set)?

Thank you for your feedback. Unfortunately we don't have any phones that supports DAB+ at the moment but I will forward your feedback about this.
- Community Manager Sony Xperia Support Forum
If you're new to our forums make sure that you have read our Discussion guidelines.
If you want to get in touch with the local support team for your country please visit our contact page.

Having problem with appletv iTunes Radio. Music stops, get spinning wheel, never restarts.

Having problem with appletv iTunes Radio. Music stops, get spinning wheel, never restarts. If I switch to another station it plays immediately, but it too sometimes stops for the same reason. Wait for 10 minutes for it to restart, then switch stations again. I've tested my download speed when it happens it's fine.

What was the connection speed when you tested
Make sure DNS is set to automatic
Reboot ATV and router
If on wifi try ethernet

I have a 2013 Dodge with a RHR radio system. I have paired my daughter's iPod to the system. However, when she wants to listen to it in the backseat via the VES it says that no device is available. Can you not listen to a paired device from the rear VES?

I have a 2013 Dodge with an RHR radio. I have paired my daughter's iPod touch to the system. When she wants to listen to it from the rear VES, it says that there is no device available even when it show connection on the iPod and on the front screen. Can you not listen to a paired device on the rear VES?

Mullaly75 wrote:
I assume u guys don't understand what open source software is
Yes, I think most of us do understand what open source software is. It sounds as if you don't. Here's some information:
Open-source software (OSS) is computer software that is available in source code form: the source code and certain other rights normally reserved forcopyright holders are provided under an open-source license that permits users to study, change, improve and at times also to distribute the software.
Open source software is very often developed in a public, collaborative manner. Open-source software is the most prominent example of open-sourcedevelopment and often compared to (technically defined) user-generated content or (legally defined) open content movements.
from http://en.wikipedia.org/wiki/Open_source_software
Yes, Tom Wu of Stanford wrote a paper on something called Secure Remote Access Protocol. It's a form of Asymetric Key Exchange and has nothing to do with hacking anything. It's actually intended to protect data.

WLC5508 with SW6500 VSS mode

Hi all,
Unfortunatelly, I haven't enough experience on CISCO wireless controller and I'm not able to find an official answer for this question:
My customer has two SW6500 on VSS mode connected via VSL. I wish to know if anyone have already connected WLC5508 with SW6500 VSS using LAG feature ?
I wish to connect one uplink from LAG to the first switch and the second uplink to the other. The two switches are considered like one logical software.
I have already read the best practice from CISCO when we connect a 5508 to a switch regarding the port-channel but nothing regarding VSS and VSL link.
Thanks in advance.

It does work as long as the two chassis are in vss:) Make sure the the etherchannel load balancing is configured for src--dst-ip
Thanks,
Scott
Help out other by using the rating system and marking answered questions as "Answered"

I'm having problem networking a Yamaha home theatre amp with vTuner (net radio) with my 2nd gen Time Capule. I only occasionally connect.

I'm having problem networking a Yamaha home theatre amp with vTuner (net radio) with my 2nd gen Time Capule. I only occasionally connect.

Remember everything outside Apple uses SMB type network protocol, not AFP..
That means all your names have to be SMB compatible.. ie
TC name, wireless names, hard disk name..
They must be short, no spaces, pure alphanumeric.
Explain how the whole network is connected.. which is the main router.. ?
How is TC2 connected to TC1?
What mode is it running in?

Non compatible with new car radio

I have a new car with a new radio made for iPods (MP Players). I have been using my other ipod, the one that looks like a stick of gum, and it works fine. I just tried my Touch and ...no sound. I can see it is charging the Touch but it won't play.
Any ideas. Didn't find any in my search of this topic.
Rob

Try putting it on music first.
The Touch is different from other iPods, so I'm not surprised that older, pre-Touch systems may not like it.
If you have an aux jack, that will work, but as you said, no charge.
I have a Scion tC with the iPod option, and it does work with the Touch - two years before the Touch was on the market, so I'm happy, but would understand if it didn't work.
Scott

How i replace default password policy with my custom password policy

Hi All,
can anybody help me to replace idm default password policy with my custom password policy?

1. Go to Security --> Policies
2. New --> String Quality Policy --> define rules --> save
3. New --> Identity System account policy --> define rules and set the policy created in step2 to for password policy --> save
4. Assign the policy created in step 3 to the user
a. when create a user, under the 'Security' tab , for the 'Account policy' select the policy created in step
b. Programattically, create /check out user view, assign the step 3 policy
<set name='user.waveset.assignedLhPolicy'>
<s>step 3 policy</s>
</set>
and checkin the view

IPod touch 2G does't work with Kenwood car radio anymore

Hi
since a few days ago, my iPod touch 2G does not work anymore with my car radio Kenwood KDC-W4544U.
When i connect the iPod to the radio, the radio display shows "Reading", which it normally shows for like 5 seconds. But now the "Reading" lasts forever, after 10 minutes of trying to let my radio read the iPod, i have no other possibility but listen to CD or radio...
I have already shut down and restarted the iPod, synched it, even restored it via iTunes. I also tried three different connection cables.
Is this a known problem and is there maybe a solution?
Thanks in advance for an answer

Problem could be solved by hard-resetting the radio

Is the iPod nano the only iPod with an FM radio receiver??

is the iPod nano the only iPod with an FM radio receiver??

You can check for yourself over on Apple's own website - http://www.apple.com/ipod/

Problems with the FM Radio after USB connection

I've been searching around for anyone else having this issue and I though I would ask before I sent my N97 phone in for repair.
Does anyone have or seen a problem with the FM radio loosing all its frequencies after it has been plugged into the USB charger? Everytime my phone is charged, my radio plays nothing by static. The radio stations are still there, but nothing but static can be heard. I have to reboot my phone to get it working. Since I listen to the radio everyday (the reason I got this phone and my n95) I am constantly rebooting this bloody thing.
Also, I have a problem rebooting my phone. Sometimes it just won't enable the buttons after the phone has been locked. The side toggle switch doesn't work, and when I touch the screen it says to unlock it. So I'm forced to remove the battery to reboot it. It doesn't happen all the time, happens about 30% of the time.
Please if anyone can help? I really don't want to send my phone in for repair.

Hello,
Try to remove the n97 battery and keep the "on" button pressed for a few seconds. Then reinsert the battery and turn the phone on. That should get rid of all the accumulated static electricity on the phone. As for your other problem, the only thing I can think of is reinstalling your current firmware and resetting your phone.

I want to buy a dock station with speakers and radio wich can support my ipad2 (30 pin connector) and also my iphone 5 (lightning)

I want to buy a dock station with speakers and radio wich can support my ipad2 (30 pin connector) and also my iphone 5 (lightning). I would be glad to get your help.

If you get the 30 pin dock get an Apple genuine adapter the rip-offs often do not work correctly
If you buy a lightning dock a company called Sandberg makes the reverse adapter ,I have one and it works correctly
As tonefox said i got the sandberg from Amazon

WLC5508 with LAP1142N ignoring Radio Policy

Similar Messages

Maybe you are looking for