WLSE 2.11, snmp and wds errors

Hello,
I try to use WLSE to manage our AP1131,1231 with different IOS version.. Some AP are in WDS domain with a WLSM, others in WDS with an AP configured to be wds master, and other are standalone without wds configured.
I have a lot of AP with error on WLSE, the most recurring ones are "Device was not reachable via SNMP" and "Inconsistent state found for query "interface.radio.basic"".
WLSE says that some device were not reachable by SNMP but snmp community is configured with a good access-list. Moreover, when I test snmp reachability from WLSE (admin>appliance>connectivity tools>SNMP Query Tool) it works fine. So I do not understand why I have this fault.
I do not understand the fault "Inconsistent state found for query "interface.radio.basic"", someone could help me perhaps ?
And the last question, some AP without wds configured have "Parent WDS for the Access Point" = 0.0.0.0.. I do not understand why..
If someone could help me for one of these troubles, it would be great
Thank You,
regards

All these faults are explained in detail at: http://www.cisco.com/univercd/cc/td/doc/product/rtrmgmt/cwparent/cw_1105/wlse/2_11/ts_gd/faults.htm
including the "Inconsistent state found for query...

Similar Messages

WLSE 2.9 and WDS AP's stuck in "Security Keys Setup"

Hey all,
I had to rebuild a WLSE, did a restore from a 2.9 CD. Restore went great, rediscovered all the devices. I am not however getting any rogue or adhoc detection.
I've found that all the WDS servers are stuck in "Security Key Setup". I've tried rebooting all the WDS servers, even the WLSE several times.
I believe that there must be some kind of key mismatch now between the WDS servers and the WLSE.
The usernames and passwords without a doubt match. It is however possible that during the rebuild setup of the WLSE that not all the same information was entered, ie domain name etc.
Does anyone know how to flush the AP's to try and negotiate a new key with the WLSE appliance?
I've tried "clear wlccp nm" and "clear wlccp ap"
Any ideas?
Thanks,
-Brian

Hey all,
Just an update for everyone.
"Security Key Setup" is a good thing, it means the WDS's have registered with the WLSE, so I was barking up the wrong tree there. I thought it meant it was trying to establish the keys.
After some more research I found my problem. Radio Monitoring was not enabled on the WLSE. I reconfigured it and everything is working great now.
Hope this helps someone.
Take care,
-Brian

Getting WDS Error

Hi, I've been having a problem with my wireless network the past couple of weeks. I have an AEBSn set up as a base station and an AEBSg and Airport Express set up as remote units in different parts of the house. This configuration worked great until about 2 weeks ago. Someone uplugged the Airport Express and after it was plugged back in I have been getting an amber flashing light indicating a WDS error on the AEBSn unit.
I look into Airport Utility and it sees all three units with the remote units coded green. At times, it seems to resolve itself and the status light goes green but after a few minutes it begins flashing amber again.
I'm getting a good signal throughout the house, it just is annoying to see the amber flashing light.
Thanks for any suggestions or hints.
Bob

There is no reason to suspect a "settings" problem here. My guess is that this error is being caused by an occasional drop in the wireless communication between the main and remote base stations.
For a start, you might try pulling power to all base stations, then plug the main base station into power and waiting for it to reboot, followed by both remote base stations. That might force the entire network to work on a different channel with a better connection than current.

Zone shutdown error - SNMP request returned error status 6 (no access)

When trying to shutdown a zone though SunMC it get the following error from the web page
SNMP request returned error status 6 (no access) snmp://xx.xx.com:nnnn/mod/scm-container/Zones/ZoneTable/ZoneEntry/zoneState#zonename
the log on the agent has
[0000008f 00a8 ]warning Nov 28 12:20:10 agent preValidateSetPDU: zoneState(zonename) [1.3.6.1.4.1.42.2
.12.2.2.85.6.1.1.10.10.98.111.116.97.110.105.120.45.97.100] - noAccess
I probably am missing a simple undocumented permissions problem.
Any help would be appreciated
Thanks

marcusj99 wrote:
When trying to shutdown a zone though SunMC it get the following error from the web page
SNMP request returned error status 6 (no access) snmp://xx.xx.com:nnnn/mod/scm-container/Zones/ZoneTable/ZoneEntry/zoneState#zonename
the log on the agent has
[0000008f 00a8 ]warning Nov 28 12:20:10 agent preValidateSetPDU: zoneState(zonename) [1.3.6.1.4.1.42.2
.12.2.2.85.6.1.1.10.10.98.111.116.97.110.105.120.45.97.100] - noAccess
I probably am missing a simple undocumented permissions problem.
Any help would be appreciatedSCM security can be tricky to get right the first time you use it. Have you performed these operations in the global zone?:
- run es-config to add your SunMC userID to the scm-container ACL?
- made sure the Project Managment and Pool Management entries are in /etc/security/prof_attr and exec_attr files?
- added your SunMC userID to the Zone/Pool/Project entries in /etc/user_attr (or used the 'usermod' command to add the entries for you)?
If any of those steps were missed then SunMC (or Solaris) may not believe you have permisson to make changes to zones/pools etc. There are a couple of SCM docs listed in with the SunMC doc set:
http://docs.sun.com/app/docs/coll/810.8?l=en
Regards,
[email protected]
http://www.HalcyonInc.com
New !! : http://forums.HalcyonInc.com !!

SCCM 2012R2 PXEboot enabled and WDS cannot install (0x80070643)

After the new year - I get back and find out WDS is missing from the SCCM server. I have tried many things and I am at the end, not sure what else I can try!
-uninstalled Windows assessment 8.1
-removed all boot images
-rebooted, installed Windows assessment 8.1, rebooted, imported default boot.wim, configured them be used with pxe, enabled pxe on the SCCM DP.
-Manually tried to install WDS, failed with the same error message (0x80070643)
What's odd is it seems like SCCM thinks PXE is up and running according to distmgr.log When I enable PXE on the DP, I get this:
ConfigureDP SMS_DISTRIBUTION_MANAGER 1/6/2014 3:01:33 AM 6520 (0x1978)
IISPortsList in the SCF is "80". SMS_DISTRIBUTION_MANAGER 1/6/2014 3:01:33 AM 6520 (0x1978)
IISSSLPortsList in the SCF is "443". SMS_DISTRIBUTION_MANAGER 1/6/2014 3:01:33 AM 6520 (0x1978)
IISWebSiteName in the SCF is "". SMS_DISTRIBUTION_MANAGER 1/6/2014 3:01:33 AM 6520 (0x1978)
IISSSLState in the SCF is 224. SMS_DISTRIBUTION_MANAGER 1/6/2014 3:01:33 AM 6520 (0x1978)
DP registry settings have been successfully updated on CO009017.starcatholic.local SMS_DISTRIBUTION_MANAGER 1/6/2014 3:01:34 AM 6520 (0x1978)
STATMSG: ID=9500 SEV=I LEV=M SOURCE="SMS Server" COMP="SMS_DISTRIBUTION_MANAGER" SYS=CO009017.starcatholic.local SITE=STT PID=1308 TID=6520 GMTDATE=Mon Jan 06 10:01:34.196 2014 ISTR0="["Display=\\CO009017.starcatholic.local\"]MSWNET:["SMS_SITE=STT"]\\CO009017.starcatholic.local\"
ISTR1="" ISTR2="" ISTR3="" ISTR4="" ISTR5="" ISTR6="" ISTR7="" ISTR8="" ISTR9="" NUMATTRS=1 AID0=404 AVAL0="["Display=\\CO009017.starcatholic.local\"]MSWNET:["SMS_SITE=STT"]\\CO009017.starcatholic.local\" SMS_DISTRIBUTION_MANAGER 1/6/2014
3:01:34 AM 6520 (0x1978)
STATMSG: ID=9503 SEV=I LEV=M SOURCE="SMS Server" COMP="SMS_DISTRIBUTION_MANAGER" SYS=CO009017.starcatholic.local SITE=STT PID=1308 TID=6520 GMTDATE=Mon Jan 06 10:01:34.238 2014 ISTR0="["Display=\\CO009017.starcatholic.local\"]MSWNET:["SMS_SITE=STT"]\\CO009017.starcatholic.local\"
ISTR1="" ISTR2="" ISTR3="" ISTR4="" ISTR5="" ISTR6="" ISTR7="" ISTR8="" ISTR9="" NUMATTRS=1 AID0=404 AVAL0="["Display=\\CO009017.starcatholic.local\"]MSWNET:["SMS_SITE=STT"]\\CO009017.starcatholic.local\" SMS_DISTRIBUTION_MANAGER 1/6/2014
3:01:34 AM 6520 (0x1978)
ConfigurePXE SMS_DISTRIBUTION_MANAGER 1/6/2014 3:01:34 AM 6520 (0x1978)
CcmInstallPXE SMS_DISTRIBUTION_MANAGER 1/6/2014 3:01:34 AM 6520 (0x1978)
PXE provider is already installed. SMS_DISTRIBUTION_MANAGER 1/6/2014 3:01:34 AM 6520 (0x1978)
DP monitoring task is disabed on server CO009017.starcatholic.local SMS_DISTRIBUTION_MANAGER 1/6/2014 3:01:34 AM 6520 (0x1978)
No need to initialize monitoring task on CO009017.starcatholic.local SMS_DISTRIBUTION_MANAGER 1/6/2014 3:01:34 AM 6520 (0x1978)
DP settings have been updated to CO009017.starcatholic.local. SMS_DISTRIBUTION_MANAGER 1/6/2014 3:01:34 AM 6520 (0x1978)
Initialize usage gathering task on CO009017.starcatholic.local SMS_DISTRIBUTION_MANAGER 1/6/2014 3:01:34 AM 6520 (0x1978)
IIS Version 7 SMS_DISTRIBUTION_MANAGER 1/6/2014 3:01:34 AM 6520 (0x1978)
context SMS_DISTRIBUTION_MANAGER 1/6/2014 3:01:35 AM 9248 (0x2420)
starcatholic\techstar SMS_DISTRIBUTION_MANAGER 1/6/2014 3:01:35 AM 9248 (0x2420)
Successfully saved iis settings. SMS_DISTRIBUTION_MANAGER 1/6/2014 3:01:35 AM 6520 (0x1978)
Log Location C:\inetpub\logs\LogFiles\W3SVC1 SMS_DISTRIBUTION_MANAGER 1/6/2014 3:01:35 AM 6520 (0x1978)
Successfully enabled usage gathering on the local distribution point. SMS_DISTRIBUTION_MANAGER 1/6/2014 3:01:35 AM 6520 (0x1978)
1998-01-01T00:00:00 SMS_DISTRIBUTION_MANAGER 1/6/2014 3:01:36 AM 6520 (0x1978)
Looking at the CBS.log after the failed attempt to install the WDS role:
https://skydrive.live.com/?cid=ba16ae946915e690&id=BA16AE946915E690%213120&action=Share
Here is the CBS file zipped up:
https://skydrive.live.com/?cid=ba16ae946915e690&id=BA16AE946915E690%213118&action=Share
Not sure if it's related or not but I am unable to install IE10 or KB2670838. The update goes, says all is well, server reboots, configures itself and then failed, reverts, reboots two times and comes back up with failed updates.
My CheckSUR.log looks clean:
=================================
Checking System Update Readiness.
Binary Version 6.1.7601.22471
Package Version 22.0
2014-01-08 13:52
Checking Windows Servicing Packages
Checking Package Manifests and Catalogs
Checking Package Watchlist
Checking Component Watchlist
Checking Packages
Checking Component Store
Summary:
Seconds executed: 841
No errors detected
I have run chkdsk /r /f, sfc /scannow - all reporting back clean.
I thought maybe it was .net 3.5 related, I uninstalled Windows Process Activation Services, tried installing updates, WDS, same issue. They all fail. Installed the latest .net 4.5.1 as well, same issue. Didn't help.
I fired up a backup from October and WDS was running on that, so it was working a few months back. Event viewer says it was working all the way up to Jan 2, 2014 and then the WDS events stop. It's like WDS got uninstalled or deleted and never to be heard
from again.
WDS Error on the day it 'left' was WDSIMGSRV Event ID 258.
The description for Event ID 258 from source WDSIMGSRV cannot be found. Either the component that raises this event is not installed on your local computer or the installation is corrupted. You can install or repair the component on the local computer.
If the event originated on another computer, the display information had to be saved with the event.
The following information was included with the event:
0xC1030104
I know there are two things here, a few updates (ie10 that cannot be installed) and WDS failing to come back up but I have a sneaky feeling they are related somehow. If one starts to work, they both do?
Server is Windows 2008 R2 SP1, hosted on a ESXi 5.1 box, VMNICs are intel based.

Thanks for the replys!
I have installed the hotfix and the server was running on 2012R2 for a month before this happened, WDS was running, I was imaging, had no issues.
I do have KB2905002 installed on the server, I did that the day after I upgraded from SP1 to R2 after I found it took 1+ hour to image a machine.
As for this:
C:\Windows\system32>wdsutil /initialize-server /REMINST:c:\remoteinstall
'wdsutil' is not recognized as an internal or external command,
operable program or batch file.
I don't have WDSUTIL on the server, it's gone. Nothing WDS related is in C:\Windows\System32 and I can't enable the role to get it going again.
Output from Powershell:
PS C:\Users\Admin> add-windowsfeature wds
add-windowsfeature : Installation of [Windows Deployment Services] Transport Server failed. Attempt to install
Transport Server failed with error code 0x80070643. Fatal error during installation
At line:1 char:1
+ add-windowsfeature wds
+ ~~~~~~~~~~~~~~~~~~~~~~
    + CategoryInfo          : OperationStopped: (:) [Add-WindowsFeature], Exception
    + FullyQualifiedErrorId : FeatureMessageDetail,Microsoft.Windows.ServerManager.Commands.AddWindowsFeatureCommand
add-windowsfeature : Installation of [Windows Deployment Services] Deployment Server failed. Attempt to install
Deployment Server failed with error code 0x80070643. Fatal error during installation
At line:1 char:1
+ add-windowsfeature wds
+ ~~~~~~~~~~~~~~~~~~~~~~
    + CategoryInfo          : OperationStopped: (:) [Add-WindowsFeature], Exception
    + FullyQualifiedErrorId : FeatureMessageDetail,Microsoft.Windows.ServerManager.Commands.AddWindowsFeatureCommand
Success Restart Needed Exit Code Feature Result
False   No             Failed    {Transport Server, Deployment Server}
I may have to end up calling Microsoft today - I don't know what to try anymore.

AEBS/relay/remote flashes WDS Errors

I am trying to set up a remote connection from the office to the gym using 3 Airport Extreme Base Stations. I currently have all 3 in a room the main connected to the DSL modem, and the remote connected to the main via ethernet.
The problem is that the main keeps flashing WDS Errors, then goes back to a Normal status. The relay would flash, then the remote. I removed the relay, and the remote seems to keep it Normal status better even as the main changes to WDS Error - it shows an error it is just for a blink. WDS Error is "This Apple wireless device is set up as part of a WDS network but no other Apple wireless devices were found." When ever the main changes status it drops it wireless clients.
If I use the main in "Create wireless network" it seems to work fine.
Anyone know why this might be happening? Can I just click ignore it since the remote is Normal most of the time?
I have set up the network following Apples Designing AirPort networks guide available online http://manuals.info.apple.com/en/DesigningAirPort_Networks10.5-Windows.pdf . I have entered the airport id in the proper place and set the WDS Mode to the proper mode for each device.
I have tried checking and unchecking the use interference robustness (makes no difference). I have checked and unchecked "Allow this network to be extended" and found there to be no difference. All three are set at Participate in a WDS network.
I have tried every channel and there is no difference.
Should the Wireless Mode on the relay/remote be Extend a wireless network? Should allow this network to be extended be checked or unchecked?
Any more ideas will be appreciated. Time to enjoy the 4th!

I have set on AEBS in the hall about 100 feet from the first. I am going though 2 steel framed drywalls and one block&brick wall. Still have about 1650kbps using iNetwork test. The problem has been getting into the gym. I can get from the hall through a glass window, courtyard, steel covered wooded door and into the kitchen. But the wall between the kitchen and gym is double thick with steel rods. I changed the location of the remote from the kitchen to the storage room, which houses the water heaters. The signal goes through the courtyard and a brick&block wall. The reading was about 400kbps and I am able to get through the wooden doors into the gym area with one bar showing on my Macbook.
I guess I will have to try something different.

WDS Error Event ID : 722

WDS & DHCP configured in same server. I getting error in WDS log file.
An error occurred while trying to create the UDP endpoint for WDSTFTP provider on interface 10.146.8.5:69. This can happen if the network interface was disabled or changed, or some other application is already using the port. The provider will not
be able to receive requests on this interface.
Error Information: 0x2740
How to reslove it

Also, please review
https://technet.microsoft.com/en-us/library/hh397405.aspx and make sure all steps are taken for running DHCP and WDS on the same server.
Jeff

SNMP and Forte

I tried to post an answer earlier, but it seems to have
gone astray.
There is shareware information and source code for
an SNMP interface on the Forte home page. Look
under "Technical Info" and then under "Shareware."
This will show you how to build an SNMP sub-agent
using tools from SNMP Research, and establish
a gateway between Forte and SNMP. The same
assembly of tools should enable you to generate
SNMP trap instructions from events generated by
your Forte programs.
Hope this helps!
All my best,
Geoff

configure: error: This build is using a GNU C compiler (gcc) while Perl has been compiled with a non-GNU (or non-working) compiler (cc). This likely won't work for building with Perl support. Either specify a different compiler (--with-cc=PATH), disable this check (--disable-perl-cc-checks) or build without Perl (--without-perl-modules).The perl supplied by Sun should be compiled with Sun Studio and the error mentioned above seems to reflect this.
So, either build perl first with sunfreeware's gcc and then move on to net-snmp or install and use Sun Studio instead of gcc so perl is happy.
alan

WDS error message

I am getting a WDS error message on my set up - saying station part of wds network but no other base stations found.
The network works fine so i could just ignore but i am interseted to understand more and the manual 'designing n network' does not help me
here is the set up: dsl modem>n base station>connected wirelessly to 3 aiport expresses (printer;itunes/hifi and ax in bedroom) and a g base station
The error message says set up N base station as a 'bridge' but if i do that the ax's and g base station don seem to connect. The raeson I am using a n base station in this is that i want to use a shared hard drive on the network
All thoughts gratefully received

Hi xhoffman,
This error can occur when you try to install Windows 7 or Windows Server 2008 R2 on a system if the following situation is true on your PC:
You are installing by using Windows 7 or Windows Server 2008 R2 RTM media.
Your system has an Intel storage controller that is configured to "RAID" mode in the BIOS. (This is a standard setting for many PC manufacturers).
The hard drive you are installing to an "Advanced Format" disk.
Please check your installation media and BIOS drive settings or download the appropriate drivers for your hard disk drive.
You could also check your setupact.log and setuperr.log for more failure details
https://technet.microsoft.com/en-us/library/hh825073.aspx?f=255&MSPPError=-2147217396
For more information or advanced methods
http://support.microsoft.com/en-us/kb/2466753
Regards
D. Wu

SCCM 2012 R2, DHCP and WDS and PXE same server

hi
I am using DHCP and PXE on same server and getting error PXE-E55: proxyDHCP did not reply to request on port 4011

HI,
To get WDS and DHCP to work on the same machine, you need to configure WDS to share the same server as DHCP, here is how it is done.
You must have a functioning DHCP server with an active scope. WDS will utilize PXE which requires a DHCP server.
Whether you plan to co-host WDS and DHCP on the same server or use two different servers you must configure WDS to listen on a specific port. DHCP and WDS both require port number 67. If you have co-hosted WDS and DHCP you can move DHCP or the PXE site role
to a separate server or use the procedure below to configure the WDS server to listen on a different port.
Modify the following registry key:
HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\WDSServer\Providers\WDSPXE
Set the registry value to:
UseDHCPPorts = 0
For the new configuration to take effect run the following command on the co-located DHCP and WDS server:
WDSUTIL /Set-Server /UseDHCPPorts:No /DHCPOption60:Yes
https://technet.microsoft.com/en-us/library/bb680753.aspx
-- My System Center blog ccmexec.com -- Twitter
@ccmexec

WDS error?

anyone else having an issue to get an Airport express to extend their Airport Extreme Network?
I did have 3 airport expresses located through out the house 1 master. and then 2 others for speakers. I replaced the master one with the new airport extreme. I got them connected and extended ok. until I went to set up the WPA2 passwords. as soon as I set up one of the express's as an WDS extender (with the password) the extreme comes back with WDS error
but I can get the expresses to connect ok with the passwords as a wireless client
Any idea's people??" (APPLEGUY)
http://forums.macrumors.com/showthread.php?t=288640
This was posted on another forum, but it was written so well and the exact problem/issue I am having....

Make sure you read this article:
Changing network security for a WDS network
The point made in that article relevant to your problem is this one:
"If you have a WDS network set up to use either no security, or 40 or 128-bit WEP, and you decide to upgrade the network security settings to WPA Personal, you will need to reset all of the base stations on the network, and then set up the WDS network again. "

Each time I try to synch photos from my Windows 7 PC to my iPad2, iTunes stops working, and the error report says Problem Event Name:     APPCRASH   Application Name:     iTunes.exe   Application Version:     10.3.1.55   Application Timestamp:     4deec35

Each time I try to synch photos from my Windows7 PC to my iPad2, iTunes stops working and the error message is:
Problem Event Name:                          APPCRASH
Application Name:                             iTunes.exe
Application Version:                           10.3.1.55
Application Timestamp:                    4deec351
Fault Module Name:                          ntdll.dll
Fault Module Version:                        6.1.7601.17514
Fault Module Timestamp:                 4ce7ba58
Exception Code:                                  c0000005
Exception Offset:                                0002e3fb
OS Version:                                          6.1.7601.2.1.0.768.3
Locale ID:                                             1033
Additional Information 1:                  0a9e
Additional Information 2:                  0a9e372d3b4ad19135b953a78882e789
Additional Information 3:                  0a9e
Additional Information 4:                  0a9e372d3b4ad19135b953a78882e789
I reloaded iTunes 10 (64 bit) successfully, but the problem remains the same.
Any suggestions?

I looked in the folder from which I want to synch photos, but there is no such thing as an "ipod photo cache" in that folder, or sub-folders, as suggested in the link which you were nice enough to provide.
I have also tried removing photos from my iPad2 Photos App, and "iTunes has stopped working" shows up again as soon as I click on the "Synch photos from" button.

2TB Ext. Hard Drive is corrupted?, error code -50 and then error code -35 when i try to empty out my trash

okay so a few days ago i received and email for one of my colleagues to do some final editing to a music video. the folder contained 2 videos a rough chops and the main which was about 2-3GB which i dragged on to my external hard drive . and at the time i was trying to install a trial version of parallel lines and me being a newbie to the software i didn't know i need windows installments for it to run lol but yeah... so i was just getting frustrated with the software i kept installing it uninstalling it and then i was thinking my the problem might be because my MacHD space is low (less then 40GBs on my MacHD), so.. i installed it on my hard drive where all my important files are (I'm a graphic designer and do light video editing) video projects and many photoshop projects form 2007 and logs and just a bunch of important files in my hard drive. so because i was so frustrated with the software i wasn't thinking and i installed it on my external 2TB hard drive. and when i realized parallel wasn't working i gave up, uninstalled the program form the hard drive and for some reason when i did that and i tried opening the video my friend had email to me and for some reason it did load up but a few seconds maybe about 10sec in the video is froze and closed my media app (VLC) and when i tried opening other video files it would freeze every few minutes but those specific files i had drag in last were not playing after at least 5 secs and eventually didn't open at all so i restart my computer login and now i get scared i see that my MacBook Pro isn't reading my external hard drive so i search threw forums... i unplug from the wall plug my external hard drive back in my computer and it loaded up but when i opened my external hard drive all my files had that plank white paper icon on my folders (because i have everything organized but subject when you open then drive folder. so... i go in to my projects and nothing, i open my edited photos and nothing... my hart feels like its about to drop and i keep opening files and there is nothing in them, but in "get info" of my drive it shows that there is filled so i go to "disk utility"... i "verify disk" passes ..."repair disk" doesn't past.... i look it up in forums... so i reboot my computer and go to the safe recovery menu. go threw the same ting "disk utility"... verify, pass... repair, pass... so now i feel relieved. i login files in the ext. hard drive load up i tried again to open the files and same thing happens... so now I'm thinking its the files i drag the files to the trash and try to empty and its gone i reboot the computer and my drive didn't load up so i tried unplugin it and back in... drive comes up i notice theres trash.. i tried emptying it and i get the error code -50. and no files are popping up on my external drive and i try to repair/unmount disk and the verify disk doesn't pass and when i click repair disk it doesn't past and another error code pops up -35.... so i felt my drive alone for a few days and yesterday i go the files deleted from the trash and now I'm not getting any codes but when i try to unmount.verify/repair the disk. keeps letting my tits need to be repaired so i click the repair button another error unable to unmount volume to repair...
what do i do? my files still don't show up. and I'm very sorry for the long paragraph but i have to be detailed for you to understand my situation

Read this.

Sender mail adapter : no messages and no error log

Hello,
I have configured a sender mail adapter to read mails from the inbox. I have used IMAP protocol. URL is specified as imap://EMHBSEXM01/Inbox. User name and password is also specified properly. I have kept poll interval to 1 minute. Messages in the inbox are in unread status. But the mail is not getting processed. I do not see anything after 1 minute. I tried using generate fetch report flag. But even then it does not create any message in SXMB_MONI. I checked runtime workbench for Mail adapter but I do not see any message for the same. Is there something that I am missing?
Thanks,
Dev

Hi All,
I chekced your responses and tried accordingly. Our basis team has given me new link now and the error message has changed. I am getting following error message.
exception caught during processing mail message; java.io.IOException: unexpected login response; read 001F BAD Command received in Invalid state.
Does anyone have any idea what this error is?
Thanks in advance,
Devendra

Plug-in errors and dependency errors with a CAF app in DS in NW CE 7.1

I am learining to build CAF apps in Developer Studio in NW CE 7.1. Here are my steps and the errors I am getting:
Open Developer Studio
Switch to the CA perspective
File->New->Project
Choose Development Component under Development Infrastructure
Press Next
Choose Composite Application under sap.com
Choose MyComponents[demo.sap.com] under 'Local Development'
Vendor: demo.sap.com
Name: carpool
Caption: Car Pool
Language: American English
Domain: SAP-xApps
Support Component: CAF-APP (typed in, not chosen)
Press Finish
The following error appears:
Status ERROR
Plugin : com.sap.ide.metamodel.core.services.eclipse
code=0
Internal error
   Plugin name: Metamodel Core
   Internal error : com.sap.ide.metamodel.core.services.eclipse
   Class      : com.sap.ide.mmservices.core.eclipse.project.ArchiveVersionChecker
   Method     : computeIdeJarProperties
   Message    : C:\Program Files\SAP\IDE\CE\eclipse\E:\Program Files\SAP\IDE\CE\eclipse\plugins\com.sap.dictionary.services_10.0.0.070821165456\lib\com.sap.dictionary.services_api.jar (The filename, directory name, or volume label syntax is incorrect)
   Exception : java.io.FileNotFoundException: C:\Program Files\SAP\IDE\CE\eclipse\E:\Program Files\SAP\IDE\CE\eclipse\plugins\com.sap.dictionary.services_10.0.0.070821165456\lib\com.sap.dictionary.services_api.jar (The filename, directory name, or volume label syntax is incorrect)
java.io.FileNotFoundException: C:\Program Files\SAP\IDE\CE\eclipse\E:\Program Files\SAP\IDE\CE\eclipse\plugins\com.sap.dictionary.services_10.0.0.070821165456\lib\com.sap.dictionary.services_api.jar (The filename, directory name, or volume label syntax is incorrect)
at java.util.zip.ZipFile.open(Native Method)
at java.util.zip.ZipFile.<init>(ZipFile.java:203)
at java.util.jar.JarFile.<init>(JarFile.java:132)
at java.util.jar.JarFile.<init>(JarFile.java:70)
at com.sap.ide.mmservices.core.eclipse.project.ArchiveVersionChecker.computeIdeJarProperties(ArchiveVersionChecker.java:296)
at com.sap.ide.mmservices.core.eclipse.project.ArchiveVersionChecker.doFullCheck(ArchiveVersionChecker.java:214)
at com.sap.ide.mmservices.core.eclipse.project.ArchiveVersionChecker.checkProject(ArchiveVersionChecker.java:125)
at com.sap.ide.mmservices.core.eclipse.generation.GenerationServiceEclipse.checkArchiveVersions(GenerationServiceEclipse.java:110)
at com.sap.dictionary.tools.generation.eclipse.GenerationBuilder.checkArchiveVersions(GenerationBuilder.java:335)
at com.sap.dictionary.tools.generation.eclipse.GenerationBuilder.build(GenerationBuilder.java:85)
at org.eclipse.core.internal.events.BuildManager$2.run(BuildManager.java:624)
at org.eclipse.core.runtime.SafeRunner.run(SafeRunner.java:37)
at org.eclipse.core.internal.events.BuildManager.basicBuild(BuildManager.java:166)
at org.eclipse.core.internal.events.BuildManager.basicBuild(BuildManager.java:197)
at org.eclipse.core.internal.events.BuildManager$1.run(BuildManager.java:246)
at org.eclipse.core.runtime.SafeRunner.run(SafeRunner.java:37)
at org.eclipse.core.internal.events.BuildManager.basicBuild(BuildManager.java:249)
at org.eclipse.core.internal.events.BuildManager.basicBuildLoop(BuildManager.java:302)
at org.eclipse.core.internal.events.BuildManager.build(BuildManager.java:334)
at org.eclipse.core.internal.events.AutoBuildJob.doBuild(AutoBuildJob.java:137)
at org.eclipse.core.internal.events.AutoBuildJob.run(AutoBuildJob.java:235)
at org.eclipse.core.internal.jobs.Worker.run(Worker.java:55)
I do not think I missed anything installing NW CE 7.1, but this error makes me think that some plug-in was erroneously left out of the install.
Incidentally, I can continue onward and build an app (this is obviously a tutorial), but when I try to deploy I get the following error:
The deployment of the archive failed with an exception!
([ERROR CODE DPL.DCAPI.1027]) DependenciesResolvingException.
Reason:[ERROR CODE DPL.DC.3033] An unresolved dependencies error
occurred while sorting the deployment batch items regarding the
dependencies.;nested exception is:
com.sap.engine.services.dc.cm.deploy.sdu_deps_resolver.UnresolvedDepen
denciesException:[ERROR CODE DPL.DC.3437]Unresolved dependencies
found for the following deployment items:
1. Component: name:'carpool~ear',vendor:'my.company',location:
'localDevelopment',version:'20080501110329',software type: 'J2EE',
dependencies:'[name:'cafruntimeear',vendor:'sap.com',name:
'cafcoreear',vendor:'sap.com']
Unresolved dependency:
name:'cafruntimeear',vendor:'sap.com'          (not found in the admitted
batch items and the repository)
Unresolved dependency:
name:'cafcoreear',vendor:'sap.com'          (not found in the admitted
batch items and the repository)
Please check the error log for further informations.
Again, this looks like I am missing some components.
Any assistance is greatly appreciated.
TB

Further developments: As you may note from the error message, DS is looking for com.sap.ide.metamodel.core.services.eclipse in both the C: and the E: drive at the same time. In fact, this file exists in the E: drive subdirectory listed, so I obviously have an error with two drive designations being concatenated. Does anyone know how I can change the lookup directory for this dependency (or any dependency)?
Thanks,
TB

WLSE 2.11, snmp and wds errors

Similar Messages

Maybe you are looking for