WLSE 2.7 Update

When is the WLSE 2.7 update going to be available for download. It was supposed to be available this past Monday but it's still not there.

It's there.
http://www.cisco.com/cgi-bin/tablebuild.pl/wlan-sol-eng
I loaded it about 2 weeks ago myself.

Similar Messages

WLSE error with new firmware 12.4-3g

when i update my 1131 APs, WLSE send this message ;
Inconsistent device state found:
CISCO-DOT11-IF-MIB cd11IfStationConfigTable.cd11IfStationRole must be in the range [1..11] (was 0)"

Hi,
Check this out,
http://tools.cisco.com/Support/BugToolKit/search/getBugDetails.do?method=fetchBugDetails&bugId=CSCsi58022
CSCsi58022 : IOD : Inconsistent Error messages in WLSE for 1130 and 1240
IOD : Inconsistent Error messages in WLSE for 1130 and 1240
Alternate Headline: IOD : Inconsistent Error messages in WLSE for 1130 and 1240
Symptom:
====================
WLSE reports a fault as follows.
Inconsistent device state found: Device "APXXXX": ifIndex=1, MAC=XX-XX-XX-XX-XX-XX: "CISCO-DOT11-IF-MIB cd11IfStationConfigTable.cd11IfStationRole must be in the range [1..11] (was 0)"
Condition:
===========
Reproducibility : unknown
Frequency : unknown
Components:
==================
WLSE Ver2.15
Aironet Ver12.4(3g)JA
Workaround:
==========
This phenomenon doesn't impact function.
Regards,
Prem

It is possible to darken the font in app Store Updates

This is just a minor thing but I am wondering if the font in Software Updates can be darkened. I am nearly blind and it is very difficult to see the font when Software Updatre is running or when it is done. I can see it by maginifiying the screen ro very large but hewn I can't see anything wlse until I reduce the maginfication to some extent.
Thanks
iMac 320, 4GB Ram, ML

Hi Charles,
Some of the Mac Accessibility features may help with your issue. You can also setup keyboard shortcuts to quickly toggle these settings on/off. For more information, see the following resource:
http://www.apple.com/support/accessibility/
Thanks,
Matt M.

Auto-Managed configurations via WLSE 2.15

I'm managing a very large roll out of AIR-AP1131AG access points, all in autonomous mode, using a WLSE running version 2.15.
Due to the current network environment, these are all being shipped out with a basic configuration as there is no dhcp service at the remote sites. I'm then using the WLSE to push out a full config to the newly installed access points.
I can manually create a configuration job and push out the final config to access points that have already been discovered and managed by the WLSE. However, I've never been able to get the Auto-Managed config option to work - the WLSE never attempts to push a config when the devices are first discovered and managed.
I hope I'm just missing something (not so) obvious in the WLSE config.
In the WLSE interface, under Configure->Auto Update->Auto-Managed Configuration->Assign Templates, I have a template created, the Enable box is checked, I have a known-good configuration template selected, and under Matching Criteria: I have Device Types checked with AP 1130 in the selection box. I also have Update device credentials checked and Copy Running configuration to Startup configuration checked.
Under Auto-Managed Configuration Options I have SSH selected as the protocol, and Email results of auto-managed configuration jobs to (my email address).
The WLSE never tries to push a config to access points when they're first managed, so I have to manually find the newly-discovered access points and create a configuration job to push the configs to them.
I have a TAC case open on this issue, but I'm having a tough time just getting the TAC engineer to respond.
What might I be missing here?
Thanks...

Such issues have happened occaisonally . I usually go about by resetting and reconfiguring WLSE from the beginning. Now I have plans to upgrade the software to see if it resolves the issue.

WLSE, WPA v1 and v2

Using
- WLSE 1130 Release 2.15.2
- AP1250 IOS 12.4(10b)XXX
Hi all,
When creating template with WLSE, we have to choose between WPA version 1 or 2, which generate IOS :
- authentication key-management wpa version 1
or
- authentication key-management wpa version 2
With Access point older than 1250, there is no consequence, Only the "Encryption settings" will be significant, and so we can use WPAv1 AND v2 simultaneously (AES CCMP+TKIP).
With an 1250 access point, In the SECURITY / SSID, for a SSID we have to choose between
- WPA
- WPA version 1
- WPA version 2
Th first one will permit to use v1 AND v2 simultaneously, whereas the second choice limit to version 1 and the third choice limit to version 2.
The problem is : In WLSE, we only have TWO CHOICES : v1 or v2 exclusively ! and not the only "WPA" choice ...
How can we specify in the template to configure the AP to use version 1 AND version 2 ?
Thanks.
SD.

V1 and V2 are workprocesses in which corresponding update bundles (by using calls to corresponding update FMs) are executed.
V1 is for primary updates (like txnl tables) while V2 is used for secondary (eg statistical LIS) updates.
You call an update FM in such task with
"call function ' ' in update task ..."
More details at http://help.sap.com/saphelp_nw04/helpdata/en/e5/de86f335cd11d3acb00000e83539c3/frameset.htm
cheers,
Ajay

WLSE Mail Alert Problem

Hi
we get alerts when there are rouge aps or ad hoc neterks. Problem is when the ssid is not broadcasted, in the wlse there is just /x/X os something like that instead of a ssid.
when i get an email from the wlse and the ssid is seen then its correct:
Subject: 020cf1f918b6[020cf1f918b6] P2 notification. FaultId : 145.
Unknown Station IBSSNetwork is: IBSSDetected. Ad-hoc network creation
detected: CMS
FaultId: 145
DeviceId: 3210
DeviceIP: 020cf1f918b6
DeviceName: 020cf1f918b6
MO: Unknown Station
Change: Ad-hoc network creation detected: CMS
ChangeSeverity: P2
StateChange: IBSSNetwork is IBSSDetected
AlarmState: Active
OverallSeverity: P2
DeviceType: L2Device
but when the ssid is not broadcasted:
Subject: 020cf1e8e5a8[020cf1e8e5a8] P2 notification. FaultId : 135.
Unknown Station IBSSNetwork is: IBSSDetected. Ad-hoc network creation
detected:
Mime-Version: 1.0
Content-Type: multipart/mixed;
boundary="29647319.1129639614015.JavaMail.casuser@wlse"
--29647319.1129639614015.JavaMail.casuser@wlse
Content-Type: text/plain; charset=us-ascii
Content-Transfer-Encoding: 7bit
FaultId: 135
DeviceId: 3067
DeviceIP: 020cf1e8e5a8
DeviceName: 020cf1e8e5a8
MO: Unknown Station
Change: Ad-hoc network creation detected:
ChangeSeverity: P2
StateChange: IBSSNetwork is IBSSDetected
AlarmState: Active
OverallSeverity: P2
DeviceType: L2Device
EstimatedLocation: Location could not be determined. Device was reported by client stations only.
--29647319.1129639614015.JavaMail.casuser@wlse--
so the mail get junked. is there a workaround that the email looks correct?
regards

I am not sure what Version of WLSE you are running, but I would recommend updating to 2.12.

WLSE 2.9 and WDS AP's stuck in "Security Keys Setup"

Hey all,
I had to rebuild a WLSE, did a restore from a 2.9 CD. Restore went great, rediscovered all the devices. I am not however getting any rogue or adhoc detection.
I've found that all the WDS servers are stuck in "Security Key Setup". I've tried rebooting all the WDS servers, even the WLSE several times.
I believe that there must be some kind of key mismatch now between the WDS servers and the WLSE.
The usernames and passwords without a doubt match. It is however possible that during the rebuild setup of the WLSE that not all the same information was entered, ie domain name etc.
Does anyone know how to flush the AP's to try and negotiate a new key with the WLSE appliance?
I've tried "clear wlccp nm" and "clear wlccp ap"
Any ideas?
Thanks,
-Brian

Hey all,
Just an update for everyone.
"Security Key Setup" is a good thing, it means the WDS's have registered with the WLSE, so I was barking up the wrong tree there. I thought it meant it was trying to establish the keys.
After some more research I found my problem. Radio Monitoring was not enabled on the WLSE. I reconfigured it and everything is working great now.
Hope this helps someone.
Take care,
-Brian

How to diable snmp in wlse (Wireless LAN Solution Engine)

Hi,
I have disabled snmp in wlse, but still snmp is showing active , when we do vunuralbility test,
can someone help me to disable this snmp in wlse.
wlse model no: Cisco 1030
software:
WLSE-2.13FCS

I checked the switch with the snmp query tool.(IP and hostname.domain-name) -works fine-.
All switches I'am interrested can be reached with the tool.cdp an snmp is enabled on all switches.
I discovered two switches:
1.cdp only discovered directly connected access points but switch 172.22.4.50. is missing.
Seed value entered: 172.22.4.50
Hop count defined: 1
CDP Discovery started at 2004-01-20 18:53:07.763 (UTC)
Device being updated :172.22.11.119 (a19.heraeus.com)
Device being updated :172.22.11.128 (a28.heraeus.com)
Device being updated :172.22.11.126 (a26.heraeus.com)
Device being updated :172.22.11.127 (a27.heraeus.com)
Number of devices (re)discovered: 4
Inventory collection does not run for updated devices, run on demand or wait for the next polling cycle.
CDP Discovery completed at 2004-01-20 18:53:08.462 (UTC)
2. cdp works fine!!! AP's and switch is discoverd.
Seed value entered: 172.22.4.42
Hop count defined: 1
CDP Discovery started at
Device being updated :172.22.11.136 (a36.heraeus.com)
Device being updated :172.22.4.42 switch.heraeus.com)
Number of devices (re)discovered: 2
CDP Discovery completed.

Wlse 2.7 and time zone

Hello
I don't find to option to set right time zone on the wlse gui. Is there an option to do that or do I have to do that with the cli?
any help welcome

You need to set the local time using the WLSE Web GUI under Administration->Appliance->Time/NTP/Webtimeout screen. Here you can also point it to a NTP server so that the time gets sync'ed automatically. There is no setting for Time Zone though.
Current local (browser) time appears in most WLSE displays. Universal Coordinated Time (UTC) is the system time and appears in log files.
To set the time that appears in the Web interface, use the above procedure. Because there is a single system clock, setting the time above also updates the UTC time.

WLSE templates

Hello,
I was trying to answer this question. It seems to me that the correct answer is B. Is this correct:
What is the primary purpose of a template in the WLSE?
A : A template is used to create a configuration model for Access Points in the network. : FALSE ?
B : Templates push out configuration files to the Access Points. TRUE ?
Thanks !

Hi Navid,
I'm going to go with B as well!
You can think of a configuration template as a configuration update file that you can apply to large numbers of devices at a time. This file might contain the update for only one parameter or a complete access point configuration.
http://www.cisco.com/en/US/products/sw/cscowork/ps3915/products_user_guide_chapter09186a0080527f41.html
Hope this helps!
Rob

Tecra M9-136 - BSOD during Vista SP2 update

Tecra M9-136 asked this morning to update to Vista SP2 and during the process the BSOD 0x0000007E arrived. Restarted in Safe Mode and the installer continued and then finally reported that the update had failed - and reverted to SP1. This took most of the morning.
It will start in Safe Mode but on a normal boot-up, Vista SP1 gets through the fingerprint recognition and then fails with the same BSOD (it doesn't get as far as displaying the desktop).
The laptop has BIOS level 1.80. I've tried in Safe mode to install 1.90 but it tells me that the battery has insufficient charge and the power adapter isn't attached. Both untrue.
Stuck - need advice. Could this be a hard fault? Can't see how I can update anything if it's a soft fault.
thanks

The message with the BSOD mentioned checking BIOS and driver versions. Anyway, no change made to that.,
I tried System Restore but the only available restore point was the SP2 installation. I thought Vista was supposed to save a restore point every 24 hours even if nothing new had been installed.
I've now found in System Information / Windows Error Reporting several messages like this:
28/09/2009 12:08 Windows Error Reporting Fault bucket 0x7E_NULL_IP_DRVNDDM+57bd, type 0
Event Name: BlueScreen
Response: None
Cab Id: 0

Problem signature:
P1: 
P2: 
P3: 
P4: 
P5: 
P6: 
P7: 
P8: 
P9: 
P10: 

Attached files:
C:\Windows\Minidump\Mini0928 09-04.dmp
C:\Users\me\AppData\Local\Te mp\WER-75660-0.sysdata.xml
C:\Users\me\AppData\L ocal\Temp\WER7D78.tmp.version.txt
& #x000d;
These files may be available here:
C:\Users\me\AppData\Local\Mic rosoft\Windows\WER\ReportArchive\Report06d1c4b5

Cannot open and update IPhoto after upgrading to OXYosemite

From the App store, I downloaded and installed OXYosemite. There are 2 more updates available: iPhoto and iMovie. When I try to upload them, the notice I get is "Update Unavailable with This Apple ID This update is not available for this Apple ID either because it was bought by a different user or the item was refunded or cancelled."
I have 2 apple IDs when I inquire about my ids. Signing in App Store with either of them, doesn't resolve the problem. I get the same notice. iTunes, Mac, mobile downloads, all use the same apple IP, only for the computer downloads from App Store isn't working.
What should I do?
Thanks, Sev

I have the same problem and can't find out how to correct it. Unable to update iPhoto or iMovie .. I get the same message as above user. Help!

Error message: "playlists selected for updating no longer exist"

I tried to update my ipod nano and I guess I had deleted a playlist, but since then, I have not been able to update. Every time I try, I get the following message:
"Cannot be updated because all of the playlists selected for updating no longer exist."
I haven't been able to highlight which playlists are selected to begin with.
I read through the manual and thought that maybe rebooting the whole system might work. So I deleted Itunes from my computer and re-installed.
Then I tried re-setting my ipod. So now I have nothing on my ipod.
I also deleted everything from my library, thinking it might help to start from scratch. Nothing has worked.
How do I "select" and "unselect" playlists so I can get up and running again?

Here you go.
http://discussions.apple.com/thread.jspa?messageID=607312&#607312

Error message iPod cannot update b/c all of the playlists no longer exist

Hello. I have been getting this error message. "Songs on the iPod "MAR(the name of my iPod)" cannot update because all of the playlists selecting for updating no longer exist." And my playlists are still on the left side in my iTunes. They do exist. I have a feeling ths might have to do with the fact that on vacation the person I was visiting gave me a gift of putting all of his music that would fit into the external hard drive part of my iPod, and for the past week or so I have been putting that music onto my 40 GB portable hard drive at home. I suspect I took a vital folder out of my iPod by accident. Right now I have the folder iPod_control if I open my iPod up in My Computer. Am I missing something? Right now my iPod is empty because iTunes made a composite playlist last week and I deleted it thinking I could get my real playlists back. Can you help me, or reccomend a site/someone who can? Thank you.
PC Windows XP

hiya!
And my playlists are still on the left side in my iTunes. They do exist.
let's just doublecheck this. folks get this message if they have "automatically update selected playlists only" selected in their itunes "ipod" preferences tab. so bring up that tab ("edit > preferences", click "ipod" while the ipod is showing up in the source list), and do a playlist by playlist crosscheck of the playlists selected in that tab, and the playlists showing up in the itunes sourcelist.
is there any playlist selected in the preferences tab that isn't showing up in the sourcelist?
love, b

Video IPOD no longer recognized by Itunes and wont Update

This is a long complicated issue. My Ipod has been working flawlessly until 2 weeks ago. Someone tried to plug it up to their computer to charge it and it wiped out my library and added their library. At first i was thinking no big deal, i will just reconnect it with my computer and it will load my library back on. However once connected to my computer it is not recognized by itunes. So i did a reset , which seemed to be working great and it started "updating" about 80% through that process it gave me an error message that says " This disc can not be written to or written from" now I have no idea why it would say that? and although it seems completely wiped out and useless, it still shows that much memeory is missing in the "about ipod" screen on the ipod. So i know the information is there somewhere , somehow?... Anyway I dont know what to do, Does anybody have any suggestions?
Oh and I have also uninstalled and reinstalled the Itunes program to make sure it is up to date. WOuld adding new songs to my library have caused this problem?

1. Try Resetting the iPod. Hold Select and Menu for 6-10 seconds - until you see the Apple Symbol.
2. Use iPod Updater to restore your iPod to factory settings.
See if those two steps clear up your problem.

WLSE 2.7 Update

Similar Messages

Maybe you are looking for