WLSE error with new firmware 12.4-3g

when i update my 1131 APs, WLSE send this message ;
Inconsistent device state found:
CISCO-DOT11-IF-MIB cd11IfStationConfigTable.cd11IfStationRole must be in the range [1..11] (was 0)"

Hi,
Check this out,
http://tools.cisco.com/Support/BugToolKit/search/getBugDetails.do?method=fetchBugDetails&bugId=CSCsi58022
CSCsi58022 : IOD : Inconsistent Error messages in WLSE for 1130 and 1240
IOD : Inconsistent Error messages in WLSE for 1130 and 1240
Alternate Headline: IOD : Inconsistent Error messages in WLSE for 1130 and 1240
Symptom:
====================
WLSE reports a fault as follows.
Inconsistent device state found: Device "APXXXX": ifIndex=1, MAC=XX-XX-XX-XX-XX-XX: "CISCO-DOT11-IF-MIB cd11IfStationConfigTable.cd11IfStationRole must be in the range [1..11] (was 0)"
Condition:
===========
Reproducibility : unknown
Frequency : unknown
Components:
==================
WLSE Ver2.15
Aironet Ver12.4(3g)JA
Workaround:
==========
This phenomenon doesn't impact function.
Regards,
Prem

Similar Messages

I tried updating my iphone 4s to the ios 7 but it said error with the firmware now my phone is stuck in recovery mode and i have no idea how to fix it any suggestions??

i tried updating my iphone 4s to the ios 7 but it said error with the firmware now my phone is stuck in recovery mode and i have no idea how to fix it any suggestions??

Try Restoring it 3 times in a row and see if that works.
If not that error can indicate one of two things: Your iPhone was at one time jailbroken, had the iOS version rolled back, or ran an unauthorized beta and if none of those things are true it is a hardware error.

Nokia N80 with NEW Firmware wont sync with PC Suit...

Hello everyone
i have my Nokia N80 on 02 network
i upgraded the old firmware to the new 4.0623 firmware without any problems at all...
now when i connect to latest version of PC Suite via bluetooth, which used to work fine with the old firmware..
PC Suite says its connected via bluetooth, but when you go to contacts, and then try tp UPDATE them, it just searches for over 15 minutes, and nothing happens..
have done everything i can, and nothing works!
why doesnt it work with new firmware?
even when i try and SYNC the phone with PC suite, it is having none of it! whats going on?

have you tried to syncronise with PC sync to see if the sync overall is in order in PC Suite.
Sometime the PC Sync might work, but the contacts folder sync in Nokia Phone Browser has zillion reasons to be stuck since it is Windwows Explorer inbedded.
By tryibg to use PC Sync you can narrow down the reasons what can go wrong

N95 photo shooting problem with new firmware V11

I have got a problem with photo shooting after upgrading my N95 (Product Code: 0534832) to the new firmware (v11.0.026) via Nokia Software Updater.
Before upgrading the firmware, I can turn off the loud and ugly snapping sound when shooting a photo; all I need to do is to change to Silent Profile (that has Warning tones OFF). But it seems that I can no longer turn that ugly sound off with the new firmware!
Is that a bug? Is there another way I can turn the sound off?

Actually I have 2 N95 phones, one is my GFs, both of them are bought and used in Hong Kong.
The way I test the differences between versions is directly comparing each feature with the two phones, where the one with new firmware has product code #0534832, and the one with old firmware has product code #0548445. Both of them has www.nokia.com.hk printed on the box and manuals, so I assume local law is not an issue.
By the way, I have just discovered that the one with product code #0548445 cannot update via Nokia Software Updater.

WRT54G v6 problems with new firmware

I performed the mandatory firmware update and soon began having problems such as DNS errors when trying to access web pages and no IP address assigned to secured wireless connections using DHCP. I reinstalled the earlier version and all of my problems vanished.
I tried reinstalling the new firmware several times with the same results each time. I ran with a backup D-Link DI-524 until I came up with the idea of rolling back the firmware.
Has anybody else experienced this??

Hello belbeebala
You should be able to find older versions at the Linksys ftp site below.
Just be sure to get the correct one.
For example, if you have the WRT54G v6, you'll want to be sure you find one that looks something like this:
wrt54gv5_v6_fw_1.00.9_US_code.zip
That version can be found down near the bottom of the link, and is just an example of the 1.00.9 Firmware made specifically for the WRT54G v5 and v6....look very carefully for the one you want/need.
Good luck.
ftp://ftp.linksys.com/pub/network

Time Capsule connecting to windows with new firmware

I have opgraded my TC´s firmware to 7.4.1, and now my PC cannot log on to the harddrive in it. I get this error message: The computer cannot connect to the TC, check that netbios is on.
This is translatet fra danish, but the meening is the same.
What is wrong???

The new firmware does not work with Windows XP. I had to revert to the last firmware, and the last version of Airport, but the good news is, you can't do that thru Windows either. You HAVE to boot thru MacOS because their instructions for Windows and the Airport do not work. You are unable to find previous versions of the firmware unless you use the Airport util thru native MacOS.

B2 Error with new MSI GTX 970 :(

Hi there team!
Just registered to try and get help. I spent around 6 hours researching + trying all the suggestions throughout many different forums, but the B2 error still persists. I am currently running the following spec:
Mobo - MSI Z68A-G43 (G3), with version 4.30 ( I flashed bios last night and still no help)
CPU - Intel® Core™ i5-2500K Processor, 3.5GHz etc.etc.
RAM - Corsair Vengeance 2x4gb at 1333MHz
GPU - MSI GTX 970 GAMING Twin Frozr V 4GB GDDR5
PSU - Cooler Master Silent Pro 700W
I have tried:
-Taking out the card and using the on-board graphics to flash the bios to later version, No help. (during this process, the B2 error does NOT show up)
-Upgraded the card to latest nVidia drivers, even uninstalled and re-installed them. No help.
-Upgraded all the drivers from MSI, i.e. chipset etc. through Live Update 6. No help.
When the card is in, I cannot even access bios, it just gets stuck at B2 screen for like a minute, and then carries on with the boot process. I am able to play games etc. after the booting, but this error for sure should not be there when the PC boots up. I didn't have any issues with my old GTX 560 TI. I've read different forums saying that it might have something to do with the mobo thinking that something has to be connected to the on-board graphics; or that flashing BIOS helped a lot of users, but not me :(.
I don't have a second PC to test the card on.
Literally, I would try anything, please someone just help :(( This card is a beast and I wanna be able to properly use it and not having to worry about this error.
Thank you very much guys, hope someone can help!

Quote from: gabe_dimitrov on 08-February-15, 20:40:51
Man thank you so much! It is finally working!!! Thank you!!!! ))) It is showing correct version in BIOS, does not show B2 error whatsoever, all done! )
Thanks for your time! You can close thread, but it's very useful for anyone that has this issue!
Wich version of BIOS do you have installed? Can you OC your processor with new BIOS?

Missing tracks with new firmware 2.11

I'm guessing that I can't be the only person on here who has had trouble managing the music on their Zen Touch after upgrading to 2..0, but I can't find any posts that mentions it. IMO the new firmware is terrible in the way it changes the way Mediasource shows the music on your player and even if you use Windows Media Player or the Windows Explorer type utitily the system of folders is rubbish as well.
Has anyone had issues with whole albums missing or ID3 tracks not showing correct information since moving to the latest firmware? When i connect my player to my PC I have a few albums which show on my PC as being on the player but when I'm using the player regularly when I'm out and about the albums are missing.
One other request. Can you guys tell me how you are transferring music to the player now? I would be interested to know if you do it through Mediasource or via copy and paste using explorer? If you do the latter where exactly do you put the music? Do you put it in the music folder under "media", and also do you put the artist folder in there or just dump the albums in there?

I could not believe how much of a **bleep** up the team at Creative had made upon installing the firmware update. Im not at all happy with the fact that it is not reversable either... It really blows ey mate?

Calendar Sync from iPhone 3G & Mobile.me to Outlook works with new firmware

YEAH - SOLUTION TO ONE PROBLEM FOUND !
Appointments I created on the Iphone do not get synced to Outlook via Mobile.me
*NO LONGER SO !*
I upgraded my firmware on my iPhone 3G to version 2.0 (5A347) by clicking on the Restore button in tha iTunes interface. It then downloads a new firmware to the iPhone and with this - I can sync all tha way !

I can't remember where I found this but it worked for me. To get appointments composed on the iPhone to sync with Outlook, the appointments must be recurring. So what I do now until Apple gets this problem fixed is make all of my appointments recurring with start and end date on the same day so they only show up once. Try it, it works for me.
Joe
Windows Parts-Pieces Windows XP Pro 3GB, 2.8GHZ
BJ Hammond
Posts: 1
From: Indiana
Registered: Jul 21, 2008
New! Re: Calendar Items Created on the iPhone do not sync to Outlook 2007
Posted: Jul 21, 2008 11:11 AM in response to: thejoeyz Reply Email
This worked for me. Thanks so much! It's still a pain in the "you know what!" Make sure you do the following.....
1. Repeat, Every Day, Save
2. End Repeat, Enter Same Date as above, Save

Still getting Javascript error with new version of UIX

I'm facing some problem after changing my UIX framework version (2.2.3030829.1626).
Currently I'm using UIX version (2.2.3030829.1626) . Paging with table is not working with new frame work .
It is giving me javacript error "object doesn't support property or method" when clicking 'Next' .
It's working fine with old version.
We had used proper cabo directory. These files are in sync with the version of the runtime
Here is our finding
I found a error in _updateFormActions() function from MarlinCoreb2.js file.
In this function it is giving error at
if(a8!=a6)
a7.action=a6 line (line # 1841,1842). If I comment out this two lines page is
working properly without any javascript error.
This problem is a bit tricky....
Because it seems to be a problem with the UIX framework that only occurs on some versions of the Internet Explorer. On some version (IE 6.0.2600.0000) it works fine
and it also works on the Mozilla Firefox browser.
Can any one advice on the same?
Thanks in advance
Anindya

I answered this question on a different thread.
Do NOT post the same question multiple times. If you require more complete or prompt assistance than you receive on these forums, contact Oracle Support.
-brian

Javascript error with new UIX framework

Hi,
I'm facing some problem after changing my UIX framework version (2.2.3030829.1626).
Currently I'm using UIX version (2.2.3030829.1626) . Paging with table is not working with new frame work .
It is giving me javacript error "object doesn't support property or method" when clicking 'Next' .
It's working fine with old version.
Any help is much appreciated.
Thanks and Regards,
Anindya

Thanks Brian for your prompt reply
We had used proper cabo directory. To confirm it we have done it once again.But we're still getting the same error.
here is our finding
I found a error in _updateFormActions() function from MarlinCoreb2.js file.
In this function it is giving error at
if(a8!=a6)
a7.action=a6 line (line # 1841,1842). If I comment out this two lines page is
working properly without any javascript error.
This problem is a bit tricky....
Because it seems to be a problem with the UIX framework that only occurs on some versions of the Internet Explorer. On some version (IE 6.0.2600.0000) it works fine
and it also works on the Mozilla Firefox browser.
can you please advice is there any solution
Thanks in advance
Anindya

Doesn't recognize my movies with new firmware

With the new firmware, I can't go to My Movies, where I have a few movies bought from Apple. I get a blank screen and I have to reboot Atv. All the rest works fine (music, tvshows, rent, etc). I guess there is a problem with that firmware and hope it will be solved soon.

is your appletv modified in any way ?

Nokia E71 problem with New Firmware 410.21.010

I have updated my Nokia E71 (RM-346) to new firmware 410.21.010. It creating a problem with battery that drain out quickly. Before update, for normal use, I need to charge once a week. But after upgrade new firmware 410.21.010. It finishes in 24 hour for normal use. I have read article that I can not downgrade, just only to wait for next firmware. Have some one any solution?
Solved!
Go to Solution.

I had a Nokia E71 running very happily on version 3 firmware. I updated the firnware to 410.21.010.
It worked fine until I switched the phone off and tried to re-start the phone. It stopped working.
It is my work phone. The messaage on the phone said take it back to my retailer. He tried to get it fixed but because Nokia say it is out of warranty I am out of a phone that is set up to use the Oki system.
It worked perfectly well until the software update.
It is now at my retailer waiting for me to collect.
This is very disappointing.
Especially as I am now considering not using a Nokia telephone ever again. Moreover, I am sure that Fair Trading would consider this matter very strange and might like ot investigate it further.
I want my E71 fixed for free by Nokia as it was working without any malfunctions until the firmware update - which was done after receiving notification from Nokia. I have not been able to use the Oki system for some weeks now and would like to contiue using Nokia. Otherwise I guess Nokia lose another customer to iPhone or HTC or Samsung. I await anyone's advice on this matter.

SRW224G4 - cant manage with new firmware thru Xmodem (dead after upgrade)

Hi All,
Before i wrote this msg, i saw few threads aboud "problem with upgrade firmware". Today i've upgraded my Linksys SRW224G4 to newest 1.2.2b and... after rebot, switch was still rebooting. I found on cisco site how to solve the problem regarding this: http://www.cisco.com/en/US/products/ps9967/products_qanda_item09186a0080a36371.shtml
So, i've made RS232 (because i don't have orginal one ; pinout 1-1 2-2 3-3 4-4 5-5) and connected to console
The problem is with hiting ESC on POST screen. My hyperterminal freezes So, i can't upload my files
Files: SRW224G4_fesm-12216.ros ; ls_106-12216.ros ; SRW224G4-1.0.0.61
------ Performing the Power-On Self Test (POST) ------
UART Channel Loopback Test........................PASS
Testing the System SDRAM..........................PASS
Boot1 Checksum Test...............................PASS
Boot2 Checksum Test...............................PASS
Flash Image Validation Test.......................PASS
BOOT Software Version 1.0.0.06 Built 23-May-2005 16:58:25
Linksys SmartSwitch based on 88E6218 with ARM946E-S.
32MByte SDRAM. I-Cache 8 KB. D-Cache 8 KB. Cache Enabled.
Autoboot in 2 seconds - press RETURN or Esc. to abort and enter prom.
Preparing to decompress...
100%
FAIL !!! Check image for valid file.
Please download a new image.
Downloading code using XMODEM.
Download failed
Perform WARM BOOT ...
------ Performing the Power-On Self Test (POST) ------
UART Channel Loopback Test........................PASS
Testing the System SDRAM..........................PASS
Boot1 Checksum Test...............................PASS
Boot2 Checksum Test...............................PASS
Flash Image Validation Test.......................PASS
BOOT Software Version 1.0.0.06 Built 23-May-2005 16:58:25
Linksys SmartSwitch based on 88E6218 with ARM946E-S.
32MByte SDRAM. I-Cache 8 KB. D-Cache 8 KB. Cache Enabled.
Autoboot in 2 seconds - press RETURN or Esc. to abort and enter prom.
Preparing to decompress...
100%
FAIL !!! Check image for valid file.
Please download a new image.
Downloading code using XMODEM.
When i try to send SRW224G4_fesm-12216.ros now, HT freezes too
Guys, what shall i do now ?
I think the RS232 cable is ok, pinout is linke normal DB9 one-to-one without crossing 2 with 3 pin.
Best regards, w8ing 4 any help.

So...
I've solved it
Problem was with settings in HT and sending ESC chacter
thank U ;D

How do you empty mail trash with new firmware

In 1.1.4 you could go to your email account click advanced and set the IPT to empty mail trash once a day. I upgraded to 2.0.1 and there is no longer a setting on that screen to set when trash is emptied. I get a lot of spam so I need to empty daily. Anyone know how to do this with the new firmware?
Thanks.

Also, you can move email to the trash folder directly from your inbox without even reading it. To do so from within your "inbox", click on "edit". You will notice there is a blue dot to the left of all new mail (shows you haven't looked at it.) When you click on edit, all the blue dots disappear.
Tap the same area where the blue dot was and a red circle will come up with a check in the center. Tap the Delete All button at the bottom and every red circled email will go directly to "trash".
In Trash, just do as the previous post says. Hit the edit button and then Delete All.
That's it and to me this is worth much more than the $9.95 for 2.0 that there is so much belly aching go on about on this forum.

WLSE error with new firmware 12.4-3g

Similar Messages

Maybe you are looking for