WM -Storage bin 3000711133 ( nothing but TO no) blocked for stock removal

Dear Friends,
1.User has created TO for 2 qty.
2.While confirming it , he has put 1 qty in qty diff - could be by mistake,
3.Now this one qty is went to stock differnece - Storage type 999 and the storage bin as "TO" number.
4.I suggested them to clear the differnces through LI21 , but they dont want to do it , as it will heat financial accounts too.
5.They want to transfer this one qty from 999 storage type to the required storage type
6.I tried with LT01 - user mvt type 999 , & also 201 , and used souce storage type as 999 and storage bin as TO no, but i am getting message -Storage bin 3000711133 ( this is nothing but TO no) blocked for stock removals
7.even i tried with LT09 - but it dosent work...
It should allow to move the material from 999 through lt01 , in our case it is not allowing, could you please help me to resolve this issue, if i need to do some customisation changes then where i have to do?
Thanks & Appreciates your earlier response.

Hello Om,
I request few corrections for my last post.
As understood now, you picked quantity was 2 pcs , while confirming user has mistakenly put 1 pc in qty difference field.
Here when user has entered 1 (reduced quantity that the delivery quantity in outbound delivery) then he has to enter difference indicator for reduced quantity which must have been configured in the system.
Now say that you have deliver the 1 pc which was confimred in TO to customer, at the same time your delivery must ahve been updated with pick and pack quantity as 1.
But still 1 qty lies in interim storage type (XXX) with stoareg bin as trsnfer order number.
Now to put this stock back in original stoarge type and bin.
You please try LT01 with movement type as 999 which is warehouse supervision.
Now in next screen you enter the stoare type (XXX) and stoareg bin i.e. your transfer order number in source data
and destination storage type and bin will be automatically picked.
Now Press Enter . 'You will get warning message as check you entries' ignore that message and save
Hope this will help you. Also if you are getting any erro message with above please give us the detailed escription of erro message
Br,
Tushar

Similar Messages

Block manual stock removal for a storage type

Hi,
Is there any configurational setting where in we can block manual stock removal (i.e creation of TO with mvt type 999) for a particular storage type.
Thanks
Prakash

Hi,
Try using the transaction LS05, give the storage type and the bin range to block all the existing bins.
But i am not sure if there is any setting at the movement type level.
Aktar

Putaway Block and Stock Removal Block en masse on Bins

Dear Gurus
Is there a way that we can put a Putaway block and Stock removal block on more than one Bin at once
Using LS11 - Change bin selectively, allows me to choose more than one bin to change, BUT the option is not there to allow me to put a putaway block and stock removal block collectively
Please advise
Many thanks
Tony

hi,
use LS06 and give the storage type and WH no...you can block all the bins for that storage type in one go for Stock removal and putaway.
Regards,
Vijay Kumar

Block upon stock removal indicator in Storage type master data

What is the significance of "Block upon stock removal" in storage type master data. Would it work if the storage type is bulk storage and SUT active?

The config setting with indicator 1 will stop you from creating more TOs for a bin in st type 425 if there are already open picking TO for that bin. In other words lets say you have a stock of material u201C79010460u201D in st type 425 u2013 B20B bin and you have created a picking TO from this bin unless you confirm this TO no more picking/stock removal TOs will be allowed and the bin will be blocked. You can see that block on bin in LS06 transaction. Once the TO is confirmed the block will be lifted automatically from the bin to create new Picking TOs.

How to put bin information to table T_QMAT thru user exit for stock remove?

Hi,
I have already use stock removal strategy 'F' and checked the flag 'User exit active', but the value in table T_QMAT filled by the standard system not include all vendors. So I need to use stock removal strategy " " and set up the table T_QMAT by the user exit.
Do you know what is the user exit and the ABAP coding to put bin information to table T_QMAT for stock removal?
Best Regards,
Chris.

Hi Chris,
You can use the exit: EXIT_SAPLL03A_005 to populate t_qmat table based on your requirements. As you have already mentioned, it is important to check the flag: User exit active in SPRO, but bear in mind the stock removal strategy has to be BLANK. If you use F, then standard SAP auto-populates the T_QMAT table.
Regards,
Narendra.

Cant get to photos so nothing but .MAc any good for photo sharing anymore !

It seems that as we cannot access the photos (easily) in iphoto 08 as it is in package that any photo sharing except .Mac is pretty well useless.. Is this correct ???
I have Flicr, Photobucket Picasa and Koffeephoto online photo sharing accounts and now I cannot upload to these because Apple seems to want hide our photos in a package . Funny that it works with .MAC but I am not paying for this service when alls I need has been available free for quite a while and my friends go there to see my photos. It almost feelings like I am being forced towards .Mac because of this.
Are other people having the same upload hassles to these other accounts because of this or is there an easy way to get this to work. I really hope I am not going to be forced to open the package and copy photos out of it and then go through the services upload programs. Have I missed something ?
Thanks

slipstream
There are three ways (at least) to get files from the iPhoto Window.
1. Drag and Drop: Drag a photo from the iPhoto Window to the desktop, there iPhoto will make a full-sized copy of the pic.
2. File -> Export: Select the files in the iPhoto Window and go File -> Export. The dialogue will give you various options, including altering the format, naming the files and changing the size. Again, producing a copy.
3. Show File: Right- (or Control-) Click on a pic and in the resulting dialogue choose 'Show File'. A Finder window will pop open with the file already selected.
To upload to MySpace or any site that does not have an iPhoto Export Plug-in the recommended way is to Select the Pic in the iPhoto Window and go File -> Export and export the pic to the desktop, then upload from there. After the upload you can trash the pic on the desktop. It's only a copy and your original is safe in iPhoto.
There are plug-ins for exporting directly to Flickr, perhaps there are for the other sites too. Search on MacUpdate
The change was made to the format of the iPhoto library because many users were inadvertently corrupting their library by browsing through it with other software or making changes in it themselves. If you're willing to risk database corruption, you can restore the older functionality simply by right clicking on the iPhoto Library and choosing 'Show Package Contents'. Then simply make an alias to the folders you require and put that alias on the desktop or where ever you want it. Be aware though, that this is a hack and not supported by Apple.
Regards
TD

Storage Location is not popullating in the PO(for stock materials)

Hi All,
we are facing a issue regarding the Storage location in SRM 5.0.(patching SAPKIBKT14) when we try to create a PO with Stock material then the PO will be created but without Storage location.But during the confirmation it will give error saying "Enter Stor. Location ".
if we enter the storage location manually it will work fine , but we need it should take automatically like other materials.Note:There is not problem if we do SC .. it will populate automatically.
Please help us.
Regards
Channappa Sajjanar

Hello Channappa,
Please maintain storage location in field "Storage loc. for EP" in MRP2 view via transaction code MM02. Once this is maintained the storage location here, it will automatically populate in the purchase order.
Hope this helps.
Thanks & Regards,
Sunil Katyare

Problem with storage Bin

Dear All,
My request is like
in material master i have assigned Storage bin ( WH2 view ) but at the time of creating Transfer Order if user put different storage bin then system accept that at post the material to other storage bin .... ( not puting material in storage bin mentioned in material master)
i want to block the TO if user mention any different storage bin at the time of creating TO
PL. HELP
With best regards
Suman

Hi
Thanks for your reply
I mention X to Addn to stock but system give same error message
If you have st.pl.str. "Fixed bin", add.to ex.st. must be allowed
MY STORAGE TYPE SETTING ARE AS FOLLOWS
1. OUTAWAY STRATEGY: F
2. STOCK REMOVAL STRATEGY : F
3. TICK ON STOCK REMOVAL REQD CONFIR
4.TICK ON FULL STK RMVL REQD. ACT
5.TICK ON RETURM MATL TO SAME STORAGE BIN
6. TICK ON SUT CHECK ACTIVE
7. TICK ON STORG.SEC.CHECK ACTIVE
please give your valuable suggestion
wuth best regards
Suman

Error storage bin

movement type 311
tcode mb1b
from sloc 00
to slco 01
quantity 20 pc
error is coming storage bin Z1 not found
settings i have done in warehouse
in 311
destination storage type   : 921
in material master : stock placement (maintianed)
                                stock removal (maintianed)
                               storage section (maintianed)
search atrategy for storage type (maintained for high rack and goods are to be removed from here )
search strategy removal and Putway BOTH ARE MAINTAINED FOR HIGH RACK AND SHELF STORAGE
Edited by: Rahul Tyagi on Feb 12, 2008 11:56 AM

i have created 4 storage types IN my warehouse Z1 and asigned this Z1 to plant and sotrage location SLOC 00 & SLOC 01 in spro>ep>assignment>le
now both the sloc are assigned to the same warehouse that is z1 so it means boththe sloc have same sotrage area avilable
goods are lying at high rack(storage area) for sloc 00
in material master storage indictor for stock placemnt mentioned sz1
entry in storage type seach is like this
Z1(WH)   E(STOCK REMOVE)    ZSI(STORAGE TYPE INDICATOR)     HIGH RACK (STORAGE TYPE)
FOR STOCK REMOVAL ENTERYS ARE IN STORAGE TYPE SEARCH LIKE THIS
Z1(WH)   A(STOCK PUTWAY)         ZRI(INDICATOR FOR STOCK PUTWAY)       SHELF STORAGE
I HAVE ALSO CREATED THE STORAGE BINS FOR ALL THE STORAGE TYPES
AND POINT TO NOTE IS Z1 IS NTO A BIN ITS THE NAME OF WAREHOUSE
IF ASSIGN INTERIM STORAGE AREA IN 311 N FIELD SOURCE THEN IT WORKS FINE
BUT IF I ASSIGN INTERIM AT DESTI THEN THE ERROR COMES AS GIVEN IN THE VERY BEGI.
AND THE RIGHT WAY IS TO ASSIGN THE SINTERIM IN THE DEST. IN 311
PLEASE SUGGEST THE SOLUTIONI CAN ALSO SEND U THE SCREEN SHOT IF U CAN PROVIDE U RMAIL ID (IF IT IS POSSIBLE FOR U)
Edited by: Rahul Tyagi on Feb 12, 2008 12:08 PM

Available stock shortfall of & in interim storage bin

Hi gurus,
I am doing the movement type 261 in MIGO with reference to a reservation.
I am working with Warehouse Management and I want to know why the system is defined in automatic the storage type 100?
When I am doing the movement 261, I know that I have stock in the storage type 007 and I am putting this, but, the system is showing the following error message:
100000000026; Available stock shortfall of 10.000 M2 in interim storage bin
Message no. L9040
Diagnosis
In Customizing, the setting is such that no negative stock is allowed in storage type 100. However, this posting will cause negative stock to exist in storage bin HE01 of storage type 100.
For my storage type 100 I do not have defined any strategy in the customising.
Could you help me with this, please?
Kind regards.
SP

Searching on the forum you can find threads about WM/PP interface settings.
(Re: WM Staging - Supply area to Production prder)
Whether WM/PP interface is active it depends on your config and master data as well.
You should check:
- config: SPRO > LE > WM > Interfaces > Define Production
- master data: routing (proper work center is assigned), work center (proper production supply area), material master(FG) (production scheduling profile), control cycle (components)
In standard system storage type 100 is defined as an interim storage type (you can compare it to storage type 902, 914, 916, etc). In control cycles (WM master data; LPK1/LPK2/LPK3) you define for each components which is the production storage type.
In standard system storage type 914 is not used with material staging. 914 s.t. related scenario: GI (261) --> stock removel from normal storage type to interim storage type (914).
100 s.t. related scenario: stock removal from normal s.t. to interim s.t. 100 --> GI (261).

Change of storage bin while cancellation of production order.

Hi Gurus,
The problem is while confirming the order the stock for that order is consuming from one storage bin (say 1ECMEL) , but when I cancel the same production order the same stock was returning to another storage bin (say 1MD01A) instead of the 1ECMEL from which it is consumed.
We want to re-move the stock after cancellation of production order to the same storage bin that from which the stock was consumed during the confirmation.
Please advise...
Thank you.
Naveen.A

Hi,
Please check the material master (mm02) in that if u have maintain default storage location in purchasing view for raw materail and workscheduling viewe for fert system will consider that as default storage bin at the time of confirmation and also for cancelation.
Please try with this.
Regards,
Nilesh

How to remove storage bin stock

our current client wants to empty out stock from storage bin. In inventory management there is no stock exist in storage location, but it is there in storage bin.
Pls suggest ASAP

Hey,
Have a look at LX23 .. might be able to help ?!
thanks,
A
Short text
Stock Comparison Inventory Management / Warehouse Management
Description
Using this report you can generate an inventory comparison between the IM System (Inventory Management) and the WM System (Warehouse Management).
On the selection screen, you can limit the area for comparison by entering the plant / storage location, plant / warehouse number or only the warehouse number.
In addition to specifying the area, you can also determine the extent of information to be issued. Here you have three options:
1. "With bin inventory"
In addition to generating the corresponding stock figures, you can also have a list of the corresponding WM bin quantities included.
2. "All data on material"
Even if only one difference occurs in one of the listed combinatations of material / batch / special stock indicator / supplier, all material combinations are listed. This can be very helpful when searching for errors.
3. "Clear differences"
If you mark this field, the system will generate a batch input session. By starting the batch input session, the differences to be cleared are removed in the IM system. Negative WM stock figures and stock differences in returns will not be cleared.
If you want to have a batch input file generated for the purpose of clearing the differences, it is important, for consistency reasons, that the materials in the respective warehouse are blocked in order that postings affecting stock figures can be prevented.
CAREFUL: If you generate this session, all the material stocks belonging to the respective warehouse number are blocked completely, that is, for the duration of the program, no postings affecting the stock in the warehouse will be possible!
Prerequisites
The comparison is also possible for warehosue numbers managed on a decentralized basis.
Output
You receive a list with various materials. The list contains the following information, for example:
The first line contains the plant, storage location, warehouse number, material number, total stock in inventory management, total stock in the warehouse, and the difference between the stocks.
The following line contains the first combination of batch / special stock indicator / supplier (or sales document and item number for sales order stock) and stock category (Q,R,S, ), the stock figures in Inventory Management, in Warehouse Management, and the difference.
If a batch input session is to be generated, the list contains a note in the log as to whether or not a session has been generated or behind the pushbutton "non-postable stocks", which materials could not be cleared because of negative stock figures or because they belong to returns stock.

Add no of quans to storage bin?

Hi,
Am an Abaper. I was using some seven quans to count for seven storage unit in a storage bin.
But i had some actions, which made storage unit availablle as 2.
Waht to do increase the storage unit , just like before.
Pls help me with the steps....
i had to do investigation on about seven storage units.. but i have only two.. hw to increase???
pls help..
Thanks in adv,
naveena.

Hi Naveena,
In general, whenever you do Goods Receipt the system will create a Quant in the storage bin. If you are doing GR for the second time, it will added to previous quant, if it is a different material, it will create a new quant, thats how Quant data will be updated in a storage bin.
In your case, i think, some one have created the deliveries and they may have done goods issue also, thats why no. of quants have been reduced.
If you want to increase the quants now, you need to do GR for the same material and the destination bin has to be the same.
Hope it is helpful

Report on Stock in storage bin

Dear Guru
My client wants a report where in MF60 they will get the required quantity to be transferred from raw storage location to production location.They want a report in which the stock to be transferred from raw storage location is in which storage bin.
Is there any standard report for this
regards
sam

Hi,
You can also use this report : LS26 to get an overview display per material.
Or you can use LS03n per WM,storage stpe, storage bin to get history.
Thanks
Silas

Create the stock in storage bin level

Hai all
     while i am doing transfer of order it is asking that storage unit type and the material stock is not maintained in storage bin .
can anybody tell me how to maintain the stock in bin level .please help me is there any tcode for that
regards
satish

Dear Satish
A storage type generally contains several storage spaces or slots. These are called storage bins in Warehouse Management (WM). The storage bin is the smallest available unit of space in a warehouse. The storage bin therefore describes the position in the warehouse where the goods are or can be stored.
Since the address of a storage bin is frequently derived from a coordinate system, a storage bin is often referred to as a coordinate. The coordinate 01-02-03 for example, can refer to a storage bin in row 1, stack 2, and level 3.
You assign each storage bin to a specific warehouse number and storage type according to its location. You must also assign each storage bin to a storage section.
You can also define the following additional characteristics of a storage bin:
         --> Maximum weight
         --> Total capacity
         --> Fire containment section
         --> Storage bin type (for example, for small or large pallets)
With certain stock placement strategies, the storage bin type plays a significant role in optimizing the automatic search for a storage bin in connection with the pallet type. For example, you can define the WM putaway strategy to place large industrial pallets into a specific large bin type and smaller pallets into small bins.
<i><b>For information on how to define storage bins, call up the Implementation Guide (IMG) for Warehouse Management and see under Master Data --> Storage Bins .</b></i>
Generally speaking, you can use any combination of letters and numbers for a storage bin coordinate with the exception of certain alphanumeric characters that are used for stock placement strategy P (according to pallet or storage unit type).
When goods are placed into storage, the system selects coordinates in ascending order according to specific sort criteria, and assigns the next available storage bin based on the coordinate structure you define for creating bins.
Thanks
G. Lakshmipathi

WM -Storage bin 3000711133 ( nothing but TO no) blocked for stock removal

Similar Messages

Maybe you are looking for