WMIC C3205: radio link break due to lower data rate

Hi,
I use a WMIC C3205 within a MAR3200 as workgroup bridge in a test bed environment. The other side of the radio link is made of LAP 1242AG controlled by a WLC2006. Only one AP is used for the time being and the link test results provide RSSI around -40dB.
Once the WMIC is associated, messages listed below are displayed when data traffic is started (IP camera, IP traffic generator).
When the WMIC is running the release 12.3(2)JL3, following traces are displayed once:
*Mar 1 00:19:18.873: %DOT11-4-UPLINK_DOWN: Interface Dot11Radio0, parent lost: Had to lower data rate
*Mar 1 00:19:21.950: %DOT11-4-UPLINK_ESTABLISHED: Interface Dot11Radio0, Associated To AP tdst_01_ap1 0018.74fb.e75f [None]
The link break duration is around 3s. When the WMIC is running the release 12.3(2)JL1, the same events occurred every 9s, but the link break duration is less than 200ms.
Does anybody know the source of this behaviour?
Best Regards,
Alain-Claude

Hi Sandesh,
Thanks for your answer. Normally, no other wlan are using the selected channel, but I will check again. My surprise is also coming from the unlike behaviour depending on the software release. I work still on this problem and will let you know.
Best Regards,
Alain-Claude

Similar Messages

  • Event Log: Interface Dot11Radio0, parent lost: Had to lower data rate

    Hi,
    AIR-AP1242
    Firmware: 12.3(8)JEB
    AP -> WGB mobil station
    The event log from WGB have often this warning:
    %DOT!!-4-UPLINK_DOWN: Interface Dot11Radio0, parent lost: Had to lower data rate
    Way?...
    It is the first installation with this description.

    Is the client able to associate to the AP and transfer data. This error message genrally indicate a weak signal strength or a bad link. Move the client to a different location and check if that works.

  • How do you fix error message "data rate for this file is too high for DVD.  You must replace this file with one of a lower data rate".

    When trying to burn a DVD it will go through the encoding step and at 98% we see the message 'data rate for this file is too high for DVD.  You must replace this file with one of a lower data rate".  We need help to correct this so we can complete burning to DVD. 

    What did you export from Premiere?
    Did you use the MPEG2-DVD preset... and did you make any changes to the preset?
    CS5-thru-CC PPro/Encore tutorial list http://forums.adobe.com/thread/1448923 may help

  • Lower Data Rates for VoWLAN

    When I take a look in the deployment guides I could see that I should not use data rates in the 802.11a network below 12mbit. We do not expect more than 6 calls and 8 phones on one access point but would like to raise the coverage by using 6mbit data rate. We could not place more access points. Is there someone with experience using lower data rates?
    Using:1252 Access Points and WISM Controller

    Allowing speeds from 6 Mbps can technically work, but the recommendation is also to avoid retries... the larger your cell, the more chances you have to have multipath issues making packets fail. With a voice deployment, if you have more than 1 % error rate, your MOS degrades below 4.1 (the quality of the call is affected and users start complaining that voice conversation is unstable, choppy etc).
    So allowing 6 Mbps is fine, but the result will depend on the quality of your RF environment...
    hope it helps
    Jerome

  • AVC INTRA 100 INGESTED CLIPS SHOWING MYSTERIOUSLY LOW DATA RATES

    Just finished my first P2 chroma key shoot using AVC Intra 100. I have ingested and transcoded using log and transfer using Pro Res 422 HQ (we shot 1080 25p) Each clip is showing a data rate of around 20mbps, yet the white paper on Pro Res suggests 200mbps data rates. Even the AVC intra files are showing data rates of around 20mbps-despite the 100mbps AVC Intra- IHow come the files are showing such low data rates? How come they are not reading 200mbps??? What did I do wrong or what am I not understanding about data rates??? Thanks

    Before all Hi Tom Hi Klaus and Hi String
    i was looking at the forum for some one that has having the same problem than i and found it!
    I'm using this new HPX-300 with the AVC-INTRA 100 codec. And when i import the content using log and transfer (final cut 7!!!) with avc-intra native plug-in, all that, to apple prores 422 hq compression the size of the video is like 14 mb/s is that right? and the quality doesn't look so good too, but this i fink is because of my computer.... AND THE INFORMATION OF THE VIDEO IN THE INFO WINDOW (more info part) IS SAYING:
    DIMENDION 1920x1080
    CODEC: AI16, LINEAR PMC, TIMECODE ---> why not apple Pro Res 422 (hq) ???
    COLOR PROFILE:HD (1-1-1) ---> This should't be 4-2-2 ?!?!?!?!?!
    If some one can explain to me who does this work i apreciate!
    And all ways Tanks for sharing!
    Message was edited by: Gustavo AVC-intra

  • IPhone convert songs to lower data rate bug

    When I use iTunes to convert my music to 128kBit/s before copying most of the covers are lost on my iPhone 4s.
    When I import the music without converting it, the covers of the songs are displayed correctly on my iPhone.
    So what can I do to fix it?
    I use the newest software on my mac and iPhone (OSX 10.7.3, iOS 5.1, iTunes 10.6)

    Also, as a note, I did everything I could to remove the other data in the past. However, it seems the files are corrupted, hence why i completely restored my iphone. Before, it took about 2.5gb space, after the restore, 700 mb, after the sync and resync, 1.28gb

  • Interoperability between MAR3200/WMIC C3205 and APC OmniAccess 4302 V2.5.3

    Hi,
    I perform interoperability test with a partner between a MAR3200 fitted with a WMIC C3205 and a APC OmniAccess 4302 running a V2.5.3 release. The association is not done.
    The WMIC generates an association request including the tags 0, 1, 133, 149 and 221. The APC association response includes only tags 0 and 1. I noticed that the association response provided by a Cisco WLC 2006 includes tags 0, 1, 133, 149 and 221 (See attached files displaying Airopeak traces).
    Does the WMIC need the 3 tags to associate? Could any of these tags be optional or at least a few fields in a tag?
    Best Regards,
    Alain-Claude

    Hi,
    The message displayed by the WMIC is the following:
    %DOT11-4-CANT_ASSOC: Interface Dot11Radio0, cannot associate: no wpa-v1 v2 chk needed
    I need urgently some information because tests are stopped until the association is not possible.
    Any link or contact would be appreciated.
    Best Regards,
    Alain-Claude

  • The radio link keeps dropping

    Hi,
    We have a pair of AP1242 setup as point to point. It was working for ages  then suddenly the radio link keeps dropping .There was no changes in the configurations and as well on the hardware and the way it setup.The signal strength values on both AP is good but one thing i have notice is on the other AP, the SNR values goes very low 3dB then it will go high more than 100,we replaced the AP and cable connected to the antenna  but we are still having the same issue.I am thinking that there might be some issue on the antenna or some interference going on that have cause this issue. is it normal for SNR value to change it value to very low and then high?
    Thanks.

    5+ D Man ...
    I agree . Also you can do a carrier busy test which could help identify interference ... Here you can read more about that on my blog ...
    http://www.my80211.com/cisco-auton-cli-commands/2010/6/20/autonomous-carrier-busy-test.html

  • Finder fails to open when starting up macbook pro due to low disk space (possibly)

    Dear forum,
    I have a Macbook Pro (13") running snow leopard and have a partitioned hard drive (half OS X and half Windows 7). This morning I was using the Mac side and was running low on disk space (very low) so I was moving desktop files into folders to free up some space. I restarted the computer to see what the free space was but the computer stopped/froze at the desktop image (no folders or dock appeared. I restarted the computer many times but the finder never opens and all I see is the desktop wallpaper. I donnected usb drives and put in dvds but the finder never appears so I cn do nothing but shut down and start up.
    I ran Disk Utility but it found no problems with the disk. I do not have a backup of the important file forlders on my drive and due to low disk space I am worried to reinstall and archive the OS since there may not be enough disk space to archive (only about 220 mb free on the apple side when I am in windows using bootcamp).
    Does anyone know what happeded to my machine? Is there such low disk space that finder had an issue? I have started on such low memory before.
    What does Archive actually do when reinstalling OS X? Does it make a copy of the HD files and folders or does it simply reinstall the operating system piece by piece while protecting the files and folders that I wish to save?
    Thanks for all your help and sorry for the length of the writing (I wanted you to understand all before replying).

    Solved
    By chance I got itunes to pop up (running hands over keys blindly) and with it the apple menu icon so I had access to my recently used items and so I could delete images from iphoto and thus bring the free disk space up above zero and then the dock/folders and finder came back....I have just backed up my important files......feeling better now
    Any advice on how to more quickly handle this type of issue next time?
    Thanks.

  • In the course of migration MacBook switched off due to low battery. After recharging progress bar doesn't change.

    In the course of migration MacBook switched off due to low battery. After recharging the progress bar doesn't move. How to continue the migration?

    I've never seen the Migration Assistant resume from sleep - for that matter I've never seen a computer go to sleep while MA was running. (If there's a next time, don't try this without the computer being plugged in.) You will probably have no choice but quit the migration and start over.

  • Communications problem with radio link

    A customer has a network composed from a LAN shared-media (with hub 8-ports), a router linked to three modems wich link to three 9.6 kbps radio links. These radio links have linked to another three modems and PC remotes. The problem is that in LAN side, we communicate with only one remote PC, and the other two remote PC can't do it. What could be the source of the problem? Maybe CSMA/CD?
    Thanks for the help.
    Filippo Ceruti

    Hi,
    r these three pc's are in the same subnet... or did u done any routing in the router...... Just chk whether u r getting atleast the mac-entries of those PC in router......
    rgs

  • Database Expert - Table Links breaking

    Hi,
    I have a set up tables and linked them... while i am designing the report i am adding new tables and command. When i do this the old links break and have to recreate all.
    Is there something to avoid this?
    Thanks

    I doubt it, version of CR you are using would help though?
    Also, don't link Tables and Commands in the same report connection, Read the warning message that pops up when you use more than one data sources as well as remove any SQLExpressions before adding more than one Source, the link goes away to create them but it does not remove them and will cause problems.
    If you have that many data sources and tables and commands I highly recommend you use a Stored Procedure and do all of your data collection server side, after all that's what DB server are designed to do and will do it much more efficient than CR ever will.
    Don

  • Links breaking once PDF documents packaged

    Good afternoon, I'm starting off with a word document that I create hyperlinks to files and folders on a shared drive.  I save the file as a PDF and all of the links work fine.  But once I package the individual PDF documents into one package all of the external hyperlinks break.  Internal links to bookmarks within the document itself work but anything pointing outside of the document or to other documents within the package break.
    I am able to use the "tools, advanced edit" to edit the hyperlink to correct the link that points to an individual document or file, but it won't allow me to point to a folder on a shared drive.  I have to select a file within the folder.
    Is it possible to package the PDF's without the links breaking to begin with?  If not how can I fix the links to point to a folder?
    Any help is greatly appreciated.
    thanks,
    Mark

    In Windows, a PDF link annotation's action does not support folders/directories as link targets.
    You mention making a "package" - is this an Acrobat 8 "Package"?
    If so, you would be creating an entirely new PDF that contains the selected files as attachments within the new PDF.
    Having changed the "environment" any external links that any of the attached files (within the "Package" PDF) have still have the explicit link syntax to a target external to the contents of the "Package" PDF.
    Or, restated - Any existing links within one attached PDF to another PDF attached within the "Package" do not have a link syntax pointing to the second PDF within the "Package".
    To have a link between files in a "Package" you'd have to make them manually with the Link tool.
    As to "Bookmarks" in MS Word - If within a Word file they will carry over into the output PDF.
    If from one MS Word file to another they do not. All you can get is a link to the target Word file.
    Note that if the link you make to the target MS Word file is explicitly to a *.doc or *.docx file that is what the target will be for the link in an output PDF.
    The Word to PDF process cannot/does not change the file extension form *.doc/*.docx to *.pdf.
    Be well...

  • Pragha: I can't play a streaming internet radio link

    I want to play an internet radio from this link: http://loudcity.com/stations/death-fm/
    But I keep getting an error "missing Gstreamer plug-in"
    I have most of the plug-ins already installed so I don't understand why its not playing. All of my other media will play with no problems, I only have an issue with streaming radio links or .pls files.
    Last edited by rg_arc (2013-03-05 22:38:19)

    Actually I've tried both ways and I get the same error.
    Just to be sure... can anyone try that link to see if it works with their Pragha setup?
    Last edited by rg_arc (2013-03-07 23:11:42)

  • I'm having problems with the reproduction of documents in Adobe X due to low reproduction quality ¿c

    I'm having problems with the reproduction of documents in Adobe X due to low reproduction quality ¿can you help me

    Some things to try...
    Using Windows Explorer navigate to C:\Program Files (x86)\Adobe\Reader 11.0\Reader, then double-click on Eula.exe and accept the license agreement
    Can you open Adobe Reader by itself?  If so, try disabling Protected Mode [Edit | Preferences | Security (Enhanced)].
    If you cannot open Reader by itself, try to disable Protected Mode in the registry; download, unzip, then run the attached registry script
    It could even be a malware issue; see http://helpx.adobe.com/acrobat/kb/reader-core-dll-error.html

Maybe you are looking for