Won't startup freezing
My iMac desktop computer won't startup anymore... Was freezing up intermittently lately, but now it gets stuck on the grey Apple logo.
I tried reinstalling OSX and no change. There are no abnormal sounds coming from it either. I am currently running the extended hardware test after reading the troubleshooting manual that came with the computer by inserting the original system disk1 in the drive and holding down the D key while powering on.
It has been running for about 6 minutes now and is almost 1/2 way done. Any ideas??? Suggestions???? Would be a great help.
Thank you in advance
And I can't find it. I'm going to leave it off and unplugged until the morning. We'll see what happens then. If nothing, I may be making an impromptu drive to the Apple Store.
Similar Messages
-
IMac won't startup - freezes on either white screen or Apple symbol
Got my 24" 2.4GHz iMac on release last year, with Tiger. Installed Leopard on it on release day.
The problem I have is that ever since a botched Boot Camp installation I've had endless problems with certain applications hanging during their startup (notably Image Capture) or refusing to quit (notably iTunes). Force Quit doesn't resolve these issues. Restarting doesn't work because Force Quit can't quit them so I have to pull the plug or otherwise force a shutdown.
Upon restarting I either get the grey screen that instantly appears, or, if I've pulled the plug and left it for a few minutes I can get to the Apple symbol but no spinner or any further start up action. Occasionally I get lucky, get back up and running, and all is well until the next crash.
All this started happening when I decided to try installing Windows on Boot Camp again. I've had it on here a couple of times since Leopard was released but usually end up deleting it eventually because either the Windows installation gets bogged down or I get bored with it and never use it. Anyway, this time, using the same discs I've always used (and yes, it's SP2, so it should be fine and anyway it's worked at least twice before) when I got to the 'restart to continue installing Windows' bit, I got the white screen and nothing happened. After an hour or so of praying and restarting endlessly trying to get a response, I finally got it to recognise my OSX installation and was up and running again. The Boot Camp volume didn't appear to be there and Disk Utility revealed zero problems whatsoever. Everything looked fine until these recurring hangs, refusals to quit apps and screwed up start-ups.
Any ideas? I don't have the expensive Apple support, but it's less than a year old! Of course, I realise that this means nothing to Apple, who seem to think I should pay a premium in order to have my machine warrantied by them for more than 90 days. Grr...
If I get it up and running I'm thinking I should just wipe the ENTIRE system absolutely clean and re-install Leopard and then use my Time Machine backup to put all my data back on (pricelessly valuable as I use the machine to work on my photography with), but I'm concerned that if there's a flaw in the System somewhere, a corruption, that installing the Time Machine backup will just reintroduce the error. On the other hand, if it's a deeply embedded and invisinle partition corruption from the bad Boot Camp installation attempt, that should be fixed by wiping the entire drive to reinstall Leopard, right?
Any ideas? I'm absolutely sick to the back teeth of this now.
Many thanks,
OwenBut service support means dragging my iMac down to an Apple Store after making an appointment that's no doubt a couple of days away. Taking a 24" iMac on public transport in London isn't something I particularly want to do.
It did actually start up eventually. I left it sitting on the Apple logo and after a few minutes it restarted itself and all was fine, until a couple of days later when two apps failed to quit, and force quit wouldn't do anything. Neither would Terminal, or Activity Monitor (it was BBEdit and Photo Mechanic this time).
I was forced to pull the plug and since then nothing whatsoever will get it past the Apple logo. Tried popping the original Tiger DVD in and running the hardware diagnostic and it says everything is fine, but trying to restart from the Tiger DVD, or the Leopard DVD, or any other DVD that's bootable, or the hard drive, or an external hard drive - all of them result in hanging at the Apple screen. Tried safe mode, tried holding Alt to choose a startup drive, everything.
What the heck do I do now?! -
What Can I do? Powerbook won't startup/Reinstall interupted/corrupted
Hi
1)imovie crashed and froze everything (finder too) on saving.
2)Now can't log in to my main admin account. Freezes after selecting it in the startup screen. It takes a LONG time to get to the users login screen.
3)Repaired Perms./Verified Disk using startup disk. No errors. Still No go.
4)I have a second account (also admin!)- It's ok.
I wouldn't be averse to deleteing an account but I need to get all my emails etc. from there.
Uh Oh
Well I made a fatal error!!!
I tried reinstalling OSX and archiving the users/settings...The installer couldn't finish.
Now the Mac won't startup
and won't work in Target disk mode!TDM just freezes both computers.
Hard drive test shows no errors. Can't check permissions though. This always stops with an error saying try again.
My only hope will be to go and buy disk warrior tomorrow and see if I can save something from the drive B4 a complete reinstall.
Any Suggestions? Please?First have you tried booting the computer from another hard drive (eg a firewire drive using the option button at startup) to see if it's a hardware problem or software problem (or a physical problem with teh internal hard drive)
based on you saying that it takes a long time to get to the login screen and target mode does not work i'd speculate that the hard drive might be on it's way out. This is what most users tend to say when there hard drive is failing. The next thing you usualy get is a horrible whiring sound. hardware test such as those in techtool don't allways show hard drive falure, my internal one recently died and techtool reports everything is within normal paramaters (even S.M.A.R.T !)
if you manage to gain access to your hard drive by whatever means then i'd suggest backing up everything you need and wiping it. then try a fresh install.
it may also help to reset the non volotile ram. to do this you need to hold commandoption+of to enter open firmware mode, then type "reset-nvram" followed by return and then "reset-all" followed by return. it will ask you for a password if you added one using the firmware utility. -
PowerMac G5 Dual 2mhz Won't startup - HELP!
Hi all,
I have a G5 (as stated above) running Tiger. Today it's totally fallen over and the fans are going crazy at every opportunity.
It started up fine this morning and then froze, so I tried re-starting it but I'm just getting as far as the Grey screen with the apple logo and 'clock' which spins until finally I get a 'no entry' symbol. I've tried re-setting the PRAM, the SMU and running disk utility. The first 2 made no difference and it crashed midway through running a verify on disk utility ('checking catalogue'). It's also frozen while starting up from the CD.
I'm entirely frustrated and about ready to throw it out of the window... or I would if I didn't have so much bloomin' work to do today that I can't get near! ARRGH!
Anyone have any suggestions please? I'm not hugely in touch with what to do when it all goes pear-shaped, so feel free to talk to me like I'm dense!
I have access to a bashed up G4 ibook in the meantime which gives me access online etc and I guess worst-case-scenario I could use as an alternative start-up disk (please advise!).
Any help gratefully received.
Cheers!
SarahArrgh! So it froze in safeboot and won't startup again... I shall persivere.
To answer your questions->
Have you tried disconnecting everything except display, and wired keyboard and mouse?
*Currently there's the G5 and monitor with the mouse and keyboard connected via the hub.*
If you Option boot - hold down the Option(alt) key on Startup - does Startup Manager find the boot DVD and internal boot drive, and regard them as viable Startup Discs?
*Yes, but... it'll sometimes allow me through to the 'choose your language' screen, sometimes as far as 'repair disk' on disk utility, or sometimes just crashing when I choose the DVD as the starter disk. It's bizarrely inconsistent. How do I just use it as a startup disk without upgrading OR repairing?*
Will the Apple Hardware Test run?
*I'm a bit of a novice (read: eejit!) at this, do you mean the Repair Disk in DU? Or the fsck command? I've done both, is this summit else I should try?*
Were any changes made to hardware or software just prior to the problem appearing?
*None that I can think of. No new software added. A few days ago (maybe a week?) there was a new 'security' update and safari upgrade that I carried out - the standard Apple variety.*
*For a wee while, every now and then the Wacom pad would freeze, but I found that by unplugging it from the hub and plugging it in again that would release it. (at the moment it's disconnected and I'm using an Apple mouse.)*
Thanks for your continued help. I am absolutely thick when it comes to repairing things when they go pear-shaped, so feel free to explain things in as basic a manner as possible.
cheers again,
Sarah -
Installed helpdesk to sles11sp1 vmware and won't startup
Hi,
I installed the service desk to sles11sp1 for vmware and it won't startup.
I am also running zenworks configuration mgmt 11 RC3 on the same server.
I installed with:
java -install install.jar -console
When prompted for a port I took the default 8700. It gave me a null and then prompted for a 1 to continue. So I selected 1 and continued.
If I http://ip:8700 I get nothing.
If I netstat -a -n|grep 8700 I get nothing.
What do I need to do to get this to work? Also I thought I could get this service desk integrated with zenworks configuration management?
GwenOriginally Posted by gleahy
got it. The startup.sh doesn't execute automatically.
How could I start the script automatically (may be by runlevel)?
I have no Idea -
Firefox won't startup so I can get to its preferences, profiles or anything else for that matter. This happens every time I try to start it up. I've recently reloaded my system software and transfered my systems settings from a backup hard drive that Time Machine (Mac app.) saved.
Firefox 4 versions and later do not run on a PowerPC Mac.
Firefox 4 and later require at least OS X 10.5 and an Intel Mac.
* http://www.mozilla.com/firefox/6.0/system-requirements/
For an Unofficial Firefox 4 compatible version (TenFourFox) that runs on PowerPC Macs with OS X 10.4.11 or OS X 10.5.8 you can look at:
* http://www.floodgap.com/software/tenfourfox/
* http://code.google.com/p/tenfourfox/
Firefox 3.6.x (Mac OS X 10.4 and later) can be found here:
* http://www.mozilla.com/en-US/firefox/all-older.html
Check and tell if its working. -
MacBook Pro 17" with Intel Core 2 Duo startup freeze with 10.6.8?
With my MacBook Pro 17" with Intel Core 2 Duo, 2.33 GHz startup freeze with 10.6.8 - I had problems after several SW upgrades. Startup ends every time in a freeze or a crash, nothing is running, i am not able to type in the password. it starts in beginning with thin colored disrupting lines on the display and this get more and more and than freeze the system.
"Save Boot", startup with shift shows no problems, display is ok, no freeze. So something must new in the video-driver. Is there any driver what I can delete or any new software to help in this issue?try to boot off the cd installazzione, when the screen appears to follow thePACKING screen viewing. If you've already looked in the manual are your problem?
-
Startup freeze 10.6.8 on macbook pro
With my MacBook Pro 17" with Intel Core 2 Duo, 2.33 GHz startup freeze with 10.6.8 -
I have problems after several Mac SW upgrades, I really use Apple SW & HW, only Microsoft Office as 3rd Party.
Startup ends every time in a freeze or a crash, nothing is running, i am not able to type in the password.
it starts in beginning with thin colored disrupting lines on the display and this get more and more and than freeze the system.
"Save Boot", startup with shift works without problems, display is ok, no freeze.
something must have changed in the video-driver? Is there any driver what I can delete or any new software to help in this issue?With my MacBook Pro 17" with Intel Core 2 Duo, 2.33 GHz startup freeze with 10.6.8 -
I have problems after several Mac SW upgrades, I really use Apple SW & HW, only Microsoft Office as 3rd Party.
Startup ends every time in a freeze or a crash, nothing is running, i am not able to type in the password.
it starts in beginning with thin colored disrupting lines on the display and this get more and more and than freeze the system.
"Save Boot", startup with shift works without problems, display is ok, no freeze.
something must have changed in the video-driver? Is there any driver what I can delete or any new software to help in this issue? -
2nd Gen iPad Mini stopped working yesterday. Won't startup under and configuration and is not recognized by my iMac. I believe it upgraded itself to iOS 8 (????)
Hey Kenneth,
So it sounds as if your iPad is not responding at all when you try to turn it on, is that correct? If so, I would suggest that you troubleshoot using the steps in this article -
If your iPhone, iPad, or iPod touch doesn't respond or doesn't turn on - Apple Support
If you get it to start up and it is still not recognized by iTunes on your Mac, use the steps in this article to troubleshoot that issue -
If you don't see your connected device in iTunes for Mac - Apple Support
Thanks for using Apple Support Communities.
Happy computing,
Brett L -
I was using my MacBook Pro Mid-2010 and then the screen went blank, I did a hard restart and went to restart again and it won't startup. The white light comes on and then the computer kinda "clicks" off!
Execute the procedures in this support article:
http://support.apple.com/kb/TS1367?viewlocale=en_US
Ciao. -
My TC won't startup with ethernet cables connected.
It will start up fine w/out ethernet cables, but with ethernet, it won't startup. I have two wired connections, my thunderbolt display/mbp and my cannon printer.
It will sit with amber light solid.
When I disconnect the two ethernet cables, it will startup fine. Then I connect the two cables and everything is good.
This is a new from apple store today 2tb TC. It's taken about 2 hours to get it setup until now I've figured out the ethernet cable issue. Is there a fix? I'm probably going to exchange it tomorrow or in the next couple of days if there's no fix provided.Well, it's working fine today. I'll continue to try it over the next couple of days and if it happens more, I'll take it back for an exchange. It happend quite a few times last night.
I have apple care for my mbp, so this should be covered on it. About 1.5 years left.
Thanks.
I'll update this post if I end up needing to exchange it. -
My G4 AGP won't startup after turning on firewire target disk mode
Can any one help me on this? I have a G4 AGP Graphics Mac running 10.4.11.
I turned on firewire target disk mode in the startup utilities to transfer files to my G5. The G4 started up in Firewire just fine and I could open it up as a drive on my G5, but the problem now is that the G4 won't startup in anything but firewire mode.
So my question is: How do you shut off the firewire target disk mode? I have tried all the keyboard commands at startup and inserted the Tiger install disk and holding the C key, but nothing will let me get me passed the Firewire Icon at startup.
Any help would be appeciated, Thanks.Hi Steve, and a warm welcome to the forums!
More things to try...
Does it boot into Open Firmware with CMDOption+of ?
http://docs.info.apple.com/article.html?artnum=42642
reset-nvram (press Enter)
set-defaults (press Enter)
reset-all (press Enter)
Have you done a PRAM reset...
http://docs.info.apple.com/article.html?artnum=2238
Tried resetting the PMU?
http://docs.info.apple.com/article.html?artnum=14449 -
My Macbook won't startup. After turn on, I get a white background screen with a folder icon (question mark inside) in the center. this icon even blinks
The battery is charging.It sounds like your hard drive is bad. If you can see it in Disk Utility you may still be able to get your files off of it. If you have one of the MacBooks with the removable battery it's very easy to put in a new hard drive.
Here's instructions on replacing your hard drive http://creativemac.digitalmedianet.com/articles/viewarticle.jsp?id=45088
To buy a hard drive try Newegg.com http://www.newegg.com/Store/SubCategory.aspx?SubCategory=380&name=Laptop-Hard-Dr ives
Here's a cheap SATA external hard drive case on eBay http://cgi.ebay.com/USB-2-5-SATA-HDD-HARD-DRIVE-EXTERNAL-ENCLOSURE-CASE-BOX-/120 636286623?pt=PCC_Drives_Storage_Internal&hash=item1c167ba69f
Put your old hard drive in an external case and after you've formatted your new hard drive and installed your operating system on it plug in your old hard drive and see if it is recognized by the new system. If so then transfer whatever files you want to the new hard drive -
IAS console and other services won´t startup after sucessfull install
Hello,
iAS 10g was successfully installed into a Suse Enterprise Linux 8. Both URLs (to the control console and to Apache) were initially working well. Just after the first reboot of the server, the services won´t startup:
ias@urano:~> $ORACLE_HOME/opmn/bin/opmnctl startall
opmnctl: starting opmn and all managed processes...
globalInitNLS: NLS boot file not found or invalid
-- default linked-in boot block used
XML parser init: error 201.
globalInitNLS: NLS boot file not found or invalid
-- default linked-in boot block used
XML parser init: error 201.
globalInitNLS: NLS boot file not found or invalid
-- default linked-in boot block used
XML parser init: error 201.
opmnctl: opmn start failed
ias@urano:~> $ORACLE_HOME/bin/emctl start iasconsole
TZ set to Etc/GMT+2
Oracle Enterprise Manager 10g Application Server Control 9.0.4.0.0
Copyright (c) 2002, 2003 Oracle Corporation. All rights reserved.
Starting Oracle 10g Application Server Control ...............
No response, checking logs for initialization activity.
waiting for response from console ............
No response, checking logs for initialization activity.
Console startup failed.
Tried to check all the logs I found but none of them seems to have registered valueable information. The enviroment variables are set as follow:
export ORACLE_SID=control
export ORACLE_BASE=/u01/app/oracle
export ORACLE_HOME=$ORACLE_BASE/product/ias
export LD_LIBRARY_PATH=$ORACLE_HOME/lib:/lib:/usr/lib:/usr/local/lib:/u01/app/product/oracle/ias/opmn/lib/
export TNS_ADMIN=/u01/app/oracle/product/9.2.0/network/admin
export NLS_LANG="BRAZILIAN PORTUGUESE_BRAZIL.WE8ISO8859P1"
export ORACLE_OWNER=ias
export ORACLE_TERM=xterm
export PATH=$PATH:/usr/bin/:$ORACLE_HOME/bin:/opt/bin:/usr/local/bin:/usr/sbin:/usr/X11R6/bin:/usr/j2sdk1.4.2_04/jre/bin:$ORACLE_HOME/opmn/bin/.
export JAVA_HOME=/usr/j2sdk1.4.2_04/
export JDK_HOME=/usr/j2sdk1.4.2_04/
export JRE_HOME=/usr/j2sdk1.4.2_04/jre
#export JAVA_HOME=/usr/java/jdk13113
#export JDK_HOME=/usr/java/jdk13113
#export JRE_HOME=/usr/java/jdk13113
export CLASSPATH=$ORACLE_HOME/jdbc/lib/classes12.zip:$ORACLE_HOME/JRE:$ORACLE_HOME/jlib:$ORACLE_HOME/rdbms/jlib:$ORACLE_HOME/network/jlib
Tried with 2 different versions of Java: JDK1.3.1.X and JDK1.4.2.X.
When I try to acess the console URL, the login window is prompted. Login and password are entered but an error is displayed:
An error has occurred!
IOException in sending Request :: Connection refused
Am I missing something? Any of you out there have already faced this problem and was able to solve it? Thanks in advance.Hello,
iAS 10g was successfully installed into a Suse Enterprise Linux 8. Both URLs (to the control console and to Apache) were initially working well. Just after the first reboot of the server, the services won´t startup:
ias@urano:~> $ORACLE_HOME/opmn/bin/opmnctl startall
opmnctl: starting opmn and all managed processes...
globalInitNLS: NLS boot file not found or invalid
-- default linked-in boot block used
XML parser init: error 201.
globalInitNLS: NLS boot file not found or invalid
-- default linked-in boot block used
XML parser init: error 201.
globalInitNLS: NLS boot file not found or invalid
-- default linked-in boot block used
XML parser init: error 201.
opmnctl: opmn start failed
ias@urano:~> $ORACLE_HOME/bin/emctl start iasconsole
TZ set to Etc/GMT+2
Oracle Enterprise Manager 10g Application Server Control 9.0.4.0.0
Copyright (c) 2002, 2003 Oracle Corporation. All rights reserved.
Starting Oracle 10g Application Server Control ...............
No response, checking logs for initialization activity.
waiting for response from console ............
No response, checking logs for initialization activity.
Console startup failed.
Tried to check all the logs I found but none of them seems to have registered valueable information. The enviroment variables are set as follow:
export ORACLE_SID=control
export ORACLE_BASE=/u01/app/oracle
export ORACLE_HOME=$ORACLE_BASE/product/ias
export LD_LIBRARY_PATH=$ORACLE_HOME/lib:/lib:/usr/lib:/usr/local/lib:/u01/app/product/oracle/ias/opmn/lib/
export TNS_ADMIN=/u01/app/oracle/product/9.2.0/network/admin
export NLS_LANG="BRAZILIAN PORTUGUESE_BRAZIL.WE8ISO8859P1"
export ORACLE_OWNER=ias
export ORACLE_TERM=xterm
export PATH=$PATH:/usr/bin/:$ORACLE_HOME/bin:/opt/bin:/usr/local/bin:/usr/sbin:/usr/X11R6/bin:/usr/j2sdk1.4.2_04/jre/bin:$ORACLE_HOME/opmn/bin/.
export JAVA_HOME=/usr/j2sdk1.4.2_04/
export JDK_HOME=/usr/j2sdk1.4.2_04/
export JRE_HOME=/usr/j2sdk1.4.2_04/jre
#export JAVA_HOME=/usr/java/jdk13113
#export JDK_HOME=/usr/java/jdk13113
#export JRE_HOME=/usr/java/jdk13113
export CLASSPATH=$ORACLE_HOME/jdbc/lib/classes12.zip:$ORACLE_HOME/JRE:$ORACLE_HOME/jlib:$ORACLE_HOME/rdbms/jlib:$ORACLE_HOME/network/jlib
Tried with 2 different versions of Java: JDK1.3.1.X and JDK1.4.2.X.
When I try to acess the console URL, the login window is prompted. Login and password are entered but an error is displayed:
An error has occurred!
IOException in sending Request :: Connection refused
Am I missing something? Any of you out there have already faced this problem and was able to solve it? Thanks in advance. -
Kernal Panic after update to 10.4.6/Missing HD Space/Won't Startup from DVD
Sorry to lump three problems together, but they may all be related.
First - I was getting random Kernal Panics while at 10.4.5, so I attempted to update to 10.4.6. The computer wouldn't even come close to starting up. I got a screen full of Kernal Panic info. I reinstalled Tiger 10.4.3, and that's where the system stands now. It's running fine.
Second - My computer suddenly announced that the startup drive was out of disk space. I looked and the window said 30g. I closed the window and opened it again only to see it at zero k. I dumped some items to get some disk space, but now I can't get my 30g back.
Third - I want to startup from the Tiger disk like I did when I reinstalled, but it won't startup from the DVD. I'd like to run Disk Repair on the main hard drive. It showed some errors when I ran a Test using the Disk Utility.
I'm hoping this is all related. The computer seems to be running fine, but I can't update or find my missing space. Any advice I can get on these issues would be appreciated. Thanks.
JonIs your computer saving a panic.log after each of the kernel panics? You can see by opening Console (in /Applications/Utilities) and looking for it. I'm not at my Mac now, so I can't tell you under what section to look for that log.
When you try to boot from the CD, are you holding down the 'C' key as the computer reboots? You can also try rebooting with the Option key pressed, which will present you with a list of bootable volumes. It will also give you access to the Apple Hardware Test (if this is the DVD that came with the computer). If you can select the Apple Hardware Test, I'd recommend doing the Extended Test, which will test the hardware, including the RAM.
For the disappearing disk space, you could have some process that is going bezerk and filling up the log files. In any event, to see where you disk space is being used, download and run Omni DiskSweeper.
Maybe you are looking for
-
HT3529 How do you turn off the voice in auto correct when messaging?
How do you turn off the voice when trying to write a message to someone?
-
Crystal XI Reports and Visual Foxpro Tables
Post Author: Pamela Vincent CA Forum: Data Connectivity and SQL I have installed XI and tried to add an ODBC connection for a database package written in Visual Foxpro 9.0 In online help there appears to be a Foxpro option in the connection info diag
-
Upgraded from DW MX 2004 to DW 8 - sites missing
when I run Dreamweaver 8 many of the sites from DW MX 2004 are missing. I tried copying the SiteCache folder from the Configuration directory, that didn't help... Shouldn't the install have found the old DW and copied over the data? sigh -terry
-
Whats the best settings for exporting a three camera youtube video on a mac book pro
I need help figureing out Whats the best settings for exporting a three camera youtube video on a mac book pro. I use 15 or 30 fps and aI cant figurwe it out [please help
-
Requesting focus for JTextField inside JPanel
I have an application with following containment hierarchy. JFrame --> JSplitPane --> JPanel. JPanel is itself a seperate class in a seperate file. I want to give focus to one of the JTextfields in JPanel, when the JPanel is intially loaded in the JF