Wont dial out

My droid will not dial out. I get a message like this "your call cannot be completed as dialed".. I know I'm dialing correctly.
I've taken the battery out and dialed #228 to program.. nothing has worked. Any idea?

Can it call other numbers and just not a specific number? If it's just 1 number I would suggest trying to call that number from another phone to see if it works. If it can't call any numbers make sure you have signal and are not in airplane mode.

Similar Messages

Phone wont dial out

I live in California, daughter is visiting New York and her phone will not dial out. Any suggestions she has tried dialing 1+ area code + number and it still wont work.

guys thanks for those who view my post.
the problem was a bad phone.

My N79 wont call out!! please help

can any one please help, my nokia n79 wont call out when i press the green button. it allows me to call out when i dial the number in manually but when go to my conacts and press the green botton it does nothing yet the green button works when i need to get on to my last numbers dialed!!
im so confused....please help!!

try the following
cred for rad 24
With all these operations I recommend you TAKE OUT MEMORY CARD and DO A BACK UP OF YOUR STUFF!!!
NOTE: In front of the hash key ( #) there is also a STAR key that people often miss and state that the code does not work.
1.. *#7780# - Restore factory settings - resets all the settings to the default ( you will not lose any data) Make sure you back up your data as you will lose all of it when you perform option 2 or 3 on this list. The default code for ALL operations listed here is 12345.
2.*#7370# - Reformat your phone (out of the box, tho keep in mind that most newer nokia phones at least n series, e series and s60 based phones have udp - user data preservation so not ALL data may be lost. still it is a good idea to always do a back up of your stuff.)3. This you perform as a last resort. Nothing else is working.If the phone is not showing any activity, proceed with hard formatting , turn off your phone, hold the following buttons while pressing the power button. (the default code is 12345)
3. hard reset - hold the following buttons * (star key), 3 (number button) and talk/green key. turn on the phone and do not release those buttons until you see the Nokia boot up screen. once you feel the phone power up you can let go off the power button while still holding all three buttons ( for Nokia 5800XM - use the following buttons to do a hard reset, /GREEN/RED/CAMERA keys pressed all at once on power up. this will only work on 5800's that have firmware version 20... and up. ) For Nokia N97 (unofficial version but works) is SHIFT /SPACE BAR / BACKSPACE while holding the power button. Again do not let go until you see the handshake screen.
If these codes are not working the only thing for you to do is contact your Nokia Care Center/Service for assistance
If i have helped at all a click on the white star below would be nice thanks.
Now using the Lumia 1520

Unity Connection 8.6 not able to forward from extension (dial out)

Dear all,
I'm having a problem at a customer where i'm not able to forward calls externally from the Unity (that's a wish too).
Basically here is the request for which I'm having an issue:
- I'm making a menu with a number XXX (CTI Port) with a System Call Handler
- Under that menu i've 3 choices which points to 3 internal numbers (YY1, YY2, YY3) (CTI Ports).
- All the CTI Ports are forwarded to international numbers which are the final destination
So the flow is the following:
NOT Working
- XXX --> Choice 1 --> YY1 --> Forwaded all to 000countrycode
Working
- XXX --> Choice 1 --> YY1 --> Forwarded all to 444 (internal number)
The strange thing is that I tested everything when I was on site by calling internally XXX from an internal number and it was able to forward all my call to the international number ...
If anyone have a clue about what I can do, I'll appreciate a lot ...
Thanks in advance
C.

Hi Taranjit,
The rules are not made to enable unity to dial out, my goal was to permit only internal calls, but in this specific case, the internal number, is a CTI Port forwarded all to the external international number...
I tried the Unity connection system handler from a internal phone and it was working perfectly, but not if the call is coming from outside apparently.
Kind regards
Christophe

MeetingPlace Express 2.1.1.2 Dial Out was not Successful

I'm configuring a MeetingPlace Express v.2.1.1.2 and I can't make the MPX do the call to the guests of a meeting.
I make the configuration test in: Services > Logs > Verify Configuration > Call configuration verification and show the following error:
==============================================================
==============================================================
Call-Config Report
Summary
WARNING:The H.323 ID should match the host name
Valid E.164 Address has been configured
H.323 gateway has been configured
Error: Dial Out was not Successful
Call-Config Report Details
H.323 Details
H.323 enabled : YES
E.164 address : 196
H.323 ID : mpxadmin
H.323 gateway 1 : 010.145.002.030
SIP enabled : YES
DialOut Session Summary
VUI Configuration: 250 Sessions, 250 Confs
*** VUI INTERNAL STATUS UTILITY ***
DebugMenu:
1) Quick Status of all Ports 4) Make Test Call
2) Verbose Status of Port Range 5) Show All Confs
3) Display complete Port Information 0) Quit
Enter the Command (0 -- 100) []: You entered 4.
Enter destination for your call: The Telephone Number is 196. Len is 3
Do you want specific ports? (t -- F): You entered f.
Placing Call .....Call was unsuccessful: Ring No Answer.
DebugMenu:
1) Quick Status of all Ports 4) Make Test Call
2) Verbose Status of Port Range 5) Show All Confs
3) Display complete Port Information 0) Quit
Enter the Command (0 -- 100) []: You entered 0.
==============================================================
==============================================================
That parameter could check?
Here I place information on the configuration of my network:
CUCM v.7.0 --> 10.145.2.10
Voice Gatweay --> 10.145.2.30
In CUCM > Device > Gateway --> Gateway: 10.145.2.20 | Description: Cisco MeetingPlace Express | Type: H.323 Gateway | IP: 10.145.2.20
Please expect your valuable help!
Thanks a lot!
ErnestoG

hi Ernesto,
As the problem you are facing is a dial out issue on MPE, go
through the checklist mentioned below in order to confirm the configuration
is intact.
Here is the checklist :
1.    Ensure that H323 GW is defined on CCM/CUCM.
Device > Gateway > find.
Look for a device name that equals either MPE's hostname, FQDN, or IP
Address.
2.    Ensure that h323 Gateways are configured on MPE.
MPE Administration Center > System Configuration > Call Configuration > H323
Configuration
Ensure that h323 is enabled.
Ensure that you have entered your CCM's IPs in h323 Gateway 1, 2
3.    Ensure that CCM's interface with MPE is up.
Ensure that MPE's IP Address is listed under the "IP Address" column.
Ensure that this IP Address is that of the FIRST NIC on MPE, not the second.
4.    Verify that MPE has the CSS required to call the destination.
FIRST, FIND MPE's CSS:
When MPE places a call, the CSS in question is Device > Gateway > MPE-GW >
Inbound
THEN the relevant config is under Device > "Call Routing Information -
Inbound Calls" > Calling Search Space
SECOND, FIND DESTINATION PATTERN's PARTITION:
If the destination is an IP Phone within the CCM/CUCM Cluster, then the
relevant config is under Device > Phone > click on Directory Number in CCM.
If the destination is a PSTN endpoint/phone, then the relevant config is
under Device > Route Pattern.
5.    Ensure that your user profile is set to allow outdials.
MPE Administration Center > User Configuration > User Profile Management >
Your User Profile > Can call out of meetings should be set to "Yes".
6.    When you place a call from from the CLI, the system applies permissions
from the "Guest" User profile since mpxadmin or root are not Users within
the MPX application. To allow this to work, you need to verify two
settings:
MPE Administration Center > User Configuration > User Profile Management >
Guest > Can call out of meetings should be set to "Yes".
Ensure that the Guest profile is not in a "locked" state.
MPE Administration Center > System Configuration > Usage Configuration >
Allow Guest outdials should be set to "Yes".
Hope this helps!
Thanks,
Karthik

Updated my Ipad and now it wont get out of recovery mode.

I have an Ipad 4 and I decided to download the latest update for it.
The download is fine until i pick it up a half hour later and it shows me the recovery mode image. Basically telling me to connect to my computer.
I go to my computer and plug it in, but then my itunes says that in order to connect I have to restore my Ipad.
I very rarely connect my ipad to my computer, and since the last sync I have reinstalled Windows 7, so its essentially a new computer and doesnt recognize my ipad.
Doesnt restore reset my ipad? I have all of my notes from my classes this symester. I cant restore!
No matter what I have done the ipad wont get out of recovery mode.
So please I need help!!
How do I get out of recovery mode?
If I cant, then dose restore wipe my files? (I dont have a backup, i rarely use my computer now, i just use my ipad)

A "Restore" WILL erase your files but you can save them. Read closely before you start.
Connect via cable to the computer that you intend to use for sync. From iTunes, select the iPad/iPod and then select the Summary tab. Follow the on-screen directions for Restore and be sure to say "yes" to the backup. You will be warned that all data (apps, music, movies, etc.) will be erased but, as the Restore finishes, you will be asked if you wish the contents of the backup to be copied to the iPad/iPod. Again, say "yes."
At the end of the basic Restore, you will be asked if you wish to sync the iPad/iPod. As before, say "yes." Note that that sync selection will disappear and the Restore will end if you do not respond within a reasonable time. If that happens, only the apps that are part of the IOS will appear on your device. Corrective action is simple - choose manual "Sync" from the bottom right of iTunes.

Problem with dial out

I have a SPA2002 adapter which I use with an asterisk server. On the asterisk I have configured call forwarding that can be enabled by dialing *21*number#. The problem is that the linksys adapter won't let me dial *21, it immediately gives a busy tone, I guess because it tries to process it as a service itself. How can I configure the adapter to dial out with *21*? I have tried to alter different parameters of the adapter configuration, but without luck.

You're mixing up two things.. there's the asterisk as in one of the button on your phone, and then there's the asterisk as in your PBX.
hwittenb was refering to the button on the phone.. your phone dialplan needs to allow dialling stuff like "*21*" - so if you can post the dialplan on your phone, we can see if it indeed allows that number to be dialled. I'm guessing it doesn't since the call never gets to your PBX.
There are two essential pieces to tracking down a problem with your VoIP equipment:
The configuration of every device involved
SIP protocol traces
And don't forget: there's no such thing as giving too much information when describing a problem.

How to turn off number sounds when dialing out?

? I have the keyboard sound off already, but, when I dial out the numbers are not silent.

The keyboard is just that, ...the keyboard, ....used only for text, email and web. The phone dialing screen is totally different and is uneffected by any changes you make to the keyboard settings. The only way to silence the phone when dialing out is to either turn the volume all the way down (not logical) or to engage the mute slide on the side of the phone. **Warning, ...both options also turn the ringer off or down. I would like to see apple address this in the next update. Users don't need to hear these loud numbers.

Ipod Touch Screen wont time out?

So about two days ago I noticed that my ipod's screen wont time out and turn off, if I for example decide to manually change a song rather then skip it from my headphones, it stays on, so i have to manually turn of the screen while I'm playing music..I don't know why I haven't changed any settings or droped it nor has any water gone in it. Is this normal? I mean its not too much of a problem but since I do use it most of the day at work it makes my battery run out much faster. Any help is much appreciated.

It might be one of two things.
I know you said you didn't change any thing but,
Check under settings, general, and autolock it might be on 'Never' change that
Or i might be misunderstanding.
You might be use a stereo base and i don't know but if you are, the ipod, if on the 'Now Playing' page is up, will not go to sleep automatically

Cannot Dial Out With a Cordless Phone

A month ago I had a phone line installed at my flat. It's a New Build so I was starting from scratch. I've tried two different cordless phones in the socket and neither will dial out. I get a dial tone, but when I punch in a number a voice tells me the number isn't recognised. Yesterday I plugged in a friend's phone which is a big old corded thing that's at least fifteen years old. It worked fine. Another friend says the only real difference is that the old phone isn't digital and that I can't use a digital phone on my phone line. Has anyone heard of this before? I'm not sure what to do. I've had nothing but trouble with BT getting my address and billing wrong and I'm sick of them. I don't want to call again and lose more of my precious life force if I don't have to.

Hi and welcome
Ensure you have unplugged all other equipment when you have tried a different phone.
Have you tried the phone (with no ADSL filter if you have Broadband) direct in the test point of your main socket?
This main socket looks like this.
remove the 2 screws each side of the socket and gently remove the bottom half, just in side the bit left on the wall you will find another socket on the right hand side, plug your phone directly into there and check if you can dial out now.
If you cant dial out correctly to here (i would try a couple of phones), there is a fault outside of your premises and you should report it to your comms provider.
If it works ok to the test socket you have a fault within your premises either on wiring or aparatus.
(If I have helped you in any way to say "Thank You" please click on the star next to the message. Thank You)
If I have solved your Issue please click the "Mark as accepted solution" button.

In Europe can't get 6126 to dial out

I unlocked my Nokia 6126 using AT&T instructions. Now I'm using a United Mobile international sim card. Every time I think I'm dialing out, I'm actually sending a text message. If I write a text, it works and gets to the person I want it to. But I can't figure out how to make a phone call. I ran through a prepaid sim card quick trying to call out and never have accomplished it. I've spoken with the sim card customer service folks and they say it's the phone. There's got to be somewhere within the menu where I can dial out, in other words make a phone call. I'm in rural Sweden if it makes a difference and my sim card is Liechtenstein. I am getting a strong signal. Help!

I think your phone is malfunctioning. Please have it fixed or replaced by a Nokia service agent.

Wont get out of recovery mode

wont come out of recovery mode tryed to downgrade cause i dont like 4.1.2 now it is stuck in rcovery mode and i cant get it out
Iphone 3g
no warrenty
stuck in recovery mode

See Here > http://support.apple.com/kb/HT1808
You may need to try this More than Once... Be sure to Follow ALL the Steps...
Take your time... Pay particular attention to Steps 3 and 4.
Some users have reported as many as 8 or 9 attempts were necessary before success.
After you have Recovered your Device...
Re-Sync your Content or Restore from the most recent Backup...
Restore from Backup > http://support.apple.com/kb/ht1766
If the issue persists...
Then a Visit to an Apple Store or AASP (Authorized Apple Service Provider) is the Next Step...
Be sure to make an appointment first...

HT4993 my phone dropped in sone water then dryed up but it still wont cme out of recovery mode.

Hi. My phone dropped in some water but now it wont come out of recovery mode.

No surprise
take it to Apple for an out of warranty exchange or you could put it in a bag of dry rice for 7 days then when it is still not working take it to Apple .
iPhone 4S is $199 US

Mobile site - can I have a web button to dial out

If a user has a mobile phone and browses the site - EG looking for a plumber....
Lets say this site says I am a plumber - here's my number......
Can we develop the page so that the user fat fingers the number and it dials out for them?
Thanks

Keep in mind that some smart phones will terminate the internet connection when the phone is dialing out.
If phone features are disabled, it won't do anything.
<a href="tel:13174562564">317-456-2564</a>
Nancy O.

My blackberry is dialing out on its own, explain how this is possible please :)

My blackberry curve dials out the same number without any attempt on my part, for instance I had left my phone on the table and it dialed out. It continued to dial out the same number until I deleted the number from my contacts.This occurred numerous times on separate occasions.
Not only did it dial out that number but also spelled out the name of the individual it dials out on a voice txt. How is this possible?
It does not dial out any other contact and ever since i've delted this contact the phone no longer dials out.
what are some explanations for this problem?

Better news my charger I was using appears to maybe be part of the thing. I wouldn't work so I got my brothers and it charges so is it possible the old charger was shorting it thus the safety bit killed the power? Maybe the angle is just happen stance.

Wont dial out

Similar Messages

Maybe you are looking for